mirror of
https://github.com/AuxXxilium/linux_dsm_epyc7002.git
synced 2024-12-05 08:16:49 +07:00
46fc133f95
DSS driver has not been "experimental" for many years now, so perhaps it's time to remove the text from Kconfig titles. Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
132 lines
3.5 KiB
Plaintext
132 lines
3.5 KiB
Plaintext
menuconfig OMAP2_DSS
|
|
tristate "OMAP2+ Display Subsystem support"
|
|
depends on ARCH_OMAP2PLUS
|
|
help
|
|
OMAP2+ Display Subsystem support.
|
|
|
|
if OMAP2_DSS
|
|
|
|
config OMAP2_VRAM_SIZE
|
|
int "VRAM size (MB)"
|
|
range 0 32
|
|
default 0
|
|
help
|
|
The amount of SDRAM to reserve at boot time for video RAM use.
|
|
This VRAM will be used by omapfb and other drivers that need
|
|
large continuous RAM area for video use.
|
|
|
|
You can also set this with "vram=<bytes>" kernel argument, or
|
|
in the board file.
|
|
|
|
config OMAP2_DSS_DEBUG_SUPPORT
|
|
bool "Debug support"
|
|
default y
|
|
help
|
|
This enables debug messages. You need to enable printing
|
|
with 'debug' module parameter.
|
|
|
|
config OMAP2_DSS_COLLECT_IRQ_STATS
|
|
bool "Collect DSS IRQ statistics"
|
|
depends on OMAP2_DSS_DEBUG_SUPPORT
|
|
default n
|
|
help
|
|
Collect DSS IRQ statistics, printable via debugfs.
|
|
|
|
The statistics can be found from
|
|
<debugfs>/omapdss/dispc_irq for DISPC interrupts, and
|
|
<debugfs>/omapdss/dsi_irq for DSI interrupts.
|
|
|
|
config OMAP2_DSS_DPI
|
|
bool "DPI support"
|
|
default y
|
|
help
|
|
DPI Interface. This is the Parallel Display Interface.
|
|
|
|
config OMAP2_DSS_RFBI
|
|
bool "RFBI support"
|
|
default n
|
|
help
|
|
MIPI DBI support (RFBI, Remote Framebuffer Interface, in Texas
|
|
Instrument's terminology).
|
|
|
|
DBI is a bus between the host processor and a peripheral,
|
|
such as a display or a framebuffer chip.
|
|
|
|
See http://www.mipi.org/ for DBI spesifications.
|
|
|
|
config OMAP2_DSS_VENC
|
|
bool "VENC support"
|
|
default y
|
|
help
|
|
OMAP Video Encoder support for S-Video and composite TV-out.
|
|
|
|
config OMAP4_DSS_HDMI
|
|
bool "HDMI support"
|
|
depends on ARCH_OMAP4
|
|
default y
|
|
help
|
|
HDMI Interface. This adds the High Definition Multimedia Interface.
|
|
See http://www.hdmi.org/ for HDMI specification.
|
|
|
|
config OMAP2_DSS_SDI
|
|
bool "SDI support"
|
|
depends on ARCH_OMAP3
|
|
default n
|
|
help
|
|
SDI (Serial Display Interface) support.
|
|
|
|
SDI is a high speed one-way display serial bus between the host
|
|
processor and a display.
|
|
|
|
config OMAP2_DSS_DSI
|
|
bool "DSI support"
|
|
depends on ARCH_OMAP3 || ARCH_OMAP4
|
|
default n
|
|
help
|
|
MIPI DSI (Display Serial Interface) support.
|
|
|
|
DSI is a high speed half-duplex serial interface between the host
|
|
processor and a peripheral, such as a display or a framebuffer chip.
|
|
|
|
See http://www.mipi.org/ for DSI spesifications.
|
|
|
|
config OMAP2_DSS_FAKE_VSYNC
|
|
bool "Fake VSYNC irq from manual update displays"
|
|
default n
|
|
help
|
|
If this is selected, DSI will generate a fake DISPC VSYNC interrupt
|
|
when DSI has sent a frame. This is only needed with DSI or RFBI
|
|
displays using manual mode, and you want VSYNC to, for example,
|
|
time animation.
|
|
|
|
config OMAP2_DSS_MIN_FCK_PER_PCK
|
|
int "Minimum FCK/PCK ratio (for scaling)"
|
|
range 0 32
|
|
default 0
|
|
help
|
|
This can be used to adjust the minimum FCK/PCK ratio.
|
|
|
|
With this you can make sure that DISPC FCK is at least
|
|
n x PCK. Video plane scaling requires higher FCK than
|
|
normally.
|
|
|
|
If this is set to 0, there's no extra constraint on the
|
|
DISPC FCK. However, the FCK will at minimum be
|
|
2xPCK (if active matrix) or 3xPCK (if passive matrix).
|
|
|
|
Max FCK is 173MHz, so this doesn't work if your PCK
|
|
is very high.
|
|
|
|
config OMAP2_DSS_SLEEP_AFTER_VENC_RESET
|
|
bool "Sleep 20ms after VENC reset"
|
|
default y
|
|
help
|
|
There is a 20ms sleep after VENC reset which seemed to fix the
|
|
reset. The reason for the bug is unclear, and it's also unclear
|
|
on what platforms this happens.
|
|
|
|
This option enables the sleep, and is enabled by default. You can
|
|
disable the sleep if it doesn't cause problems on your platform.
|
|
|
|
endif
|