mirror of
https://github.com/AuxXxilium/linux_dsm_epyc7002.git
synced 2024-12-27 15:25:02 +07:00
1004a2977b
Use the new EBI/NAND bindings to declare NAND chips and remove old NAND nodes along the way. Note that we keep using old bindings in at91rm9200.dtsi because this SoC is not supported by the EBI driver. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Tested-by: Peter Rosin <peda@axentia.se> Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
124 lines
2.1 KiB
Plaintext
124 lines
2.1 KiB
Plaintext
/*
|
|
* aks-cdu.dts - Device Tree file for AK signal CDU
|
|
*
|
|
* Copyright (C) 2012 AK signal Brno a.s.
|
|
* 2012 Jiri Prchal <jiri.prchal@aksignal.cz>
|
|
*
|
|
* Licensed under GPLv2 or later.
|
|
*/
|
|
|
|
/dts-v1/;
|
|
|
|
#include "ge863-pro3.dtsi"
|
|
|
|
/ {
|
|
chosen {
|
|
bootargs = "console=ttyS0,115200 ubi.mtd=4 root=ubi0:rootfs rootfstype=ubifs";
|
|
};
|
|
|
|
clocks {
|
|
slow_xtal {
|
|
clock-frequency = <32768>;
|
|
};
|
|
};
|
|
|
|
ahb {
|
|
apb {
|
|
usart0: serial@fffb0000 {
|
|
status = "okay";
|
|
};
|
|
|
|
usart1: serial@fffb4000 {
|
|
status = "okay";
|
|
linux,rs485-enabled-at-boot-time;
|
|
rs485-rts-delay = <0 0>;
|
|
};
|
|
|
|
usart2: serial@fffb8000 {
|
|
status = "okay";
|
|
linux,rs485-enabled-at-boot-time;
|
|
rs485-rts-delay = <0 0>;
|
|
};
|
|
|
|
usart3: serial@fffd0000 {
|
|
status = "okay";
|
|
linux,rs485-enabled-at-boot-time;
|
|
rs485-rts-delay = <0 0>;
|
|
};
|
|
|
|
macb0: ethernet@fffc4000 {
|
|
phy-mode = "rmii";
|
|
status = "okay";
|
|
};
|
|
|
|
usb1: gadget@fffa4000 {
|
|
atmel,vbus-gpio = <&pioC 15 GPIO_ACTIVE_HIGH>;
|
|
status = "okay";
|
|
};
|
|
};
|
|
|
|
usb0: ohci@500000 {
|
|
num-ports = <2>;
|
|
status = "okay";
|
|
};
|
|
|
|
ebi: ebi@10000000 {
|
|
nand_controller: nand-controller {
|
|
nand: nand@3 {
|
|
partitions {
|
|
bootstrap@0 {
|
|
label = "bootstrap";
|
|
reg = <0x0 0x40000>;
|
|
};
|
|
|
|
uboot@40000 {
|
|
label = "uboot";
|
|
reg = <0x40000 0x80000>;
|
|
};
|
|
|
|
ubootenv@c0000 {
|
|
label = "ubootenv";
|
|
reg = <0xc0000 0x40000>;
|
|
};
|
|
|
|
kernel@100000 {
|
|
label = "kernel";
|
|
reg = <0x100000 0x400000>;
|
|
};
|
|
|
|
rootfs@500000 {
|
|
label = "rootfs";
|
|
reg = <0x500000 0x7b00000>;
|
|
};
|
|
};
|
|
};
|
|
};
|
|
};
|
|
};
|
|
|
|
leds {
|
|
compatible = "gpio-leds";
|
|
|
|
red {
|
|
gpios = <&pioC 10 GPIO_ACTIVE_HIGH>;
|
|
linux,default-trigger = "none";
|
|
};
|
|
|
|
green {
|
|
gpios = <&pioA 5 GPIO_ACTIVE_LOW>;
|
|
linux,default-trigger = "none";
|
|
default-state = "on";
|
|
};
|
|
|
|
yellow {
|
|
gpios = <&pioB 20 GPIO_ACTIVE_LOW>;
|
|
linux,default-trigger = "none";
|
|
};
|
|
|
|
blue {
|
|
gpios = <&pioB 21 GPIO_ACTIVE_LOW>;
|
|
linux,default-trigger = "none";
|
|
};
|
|
};
|
|
};
|