linux_dsm_epyc7002/arch/arm/boot/dts/imx23-olinuxino.dts
Fabio Estevam 098e752289 ARM: dts: imx23-olinuxino: Use pinctrl for gpio-led
Since commit 8fe4554f (leds: leds-gpio: adopt pinctrl support) gpio-led driver
has pinctrl support, so setup the gpio led pin via pinctrl and avoid the
following warning:

leds-gpio leds.5: pins are not configured from the driver

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
2012-10-15 10:51:49 +08:00

112 lines
2.2 KiB
Plaintext

/*
* Copyright 2012 Freescale Semiconductor, Inc.
*
* Author: Fabio Estevam <fabio.estevam@freescale.com>
*
* The code contained herein is licensed under the GNU General Public
* License. You may obtain a copy of the GNU General Public License
* Version 2 or later at the following locations:
*
* http://www.opensource.org/licenses/gpl-license.html
* http://www.gnu.org/copyleft/gpl.html
*/
/dts-v1/;
/include/ "imx23.dtsi"
/ {
model = "i.MX23 Olinuxino Low Cost Board";
compatible = "olimex,imx23-olinuxino", "fsl,imx23";
memory {
reg = <0x40000000 0x04000000>;
};
apb@80000000 {
apbh@80000000 {
ssp0: ssp@80010000 {
compatible = "fsl,imx23-mmc";
pinctrl-names = "default";
pinctrl-0 = <&mmc0_4bit_pins_a &mmc0_pins_fixup>;
bus-width = <4>;
status = "okay";
};
pinctrl@80018000 {
pinctrl-names = "default";
pinctrl-0 = <&hog_pins_a>;
hog_pins_a: hog@0 {
reg = <0>;
fsl,pinmux-ids = <
0x2013 /* MX23_PAD_SSP1_DETECT__GPIO_2_1 */
>;
fsl,drive-strength = <0>;
fsl,voltage = <1>;
fsl,pull-up = <0>;
};
led_pin_gpio0_17: led_gpio0_17@0 {
reg = <0>;
fsl,pinmux-ids = <
0x0113 /* MX23_PAD_GPMI_ALE__GPIO_0_17 */
>;
fsl,drive-strength = <0>;
fsl,voltage = <1>;
fsl,pull-up = <0>;
};
};
};
apbx@80040000 {
duart: serial@80070000 {
pinctrl-names = "default";
pinctrl-0 = <&duart_pins_a>;
status = "okay";
};
auart0: serial@8006c000 {
pinctrl-names = "default";
pinctrl-0 = <&auart0_2pins_a>;
status = "okay";
};
usbphy0: usbphy@8007c000 {
status = "okay";
};
};
};
ahb@80080000 {
usb0: usb@80080000 {
vbus-supply = <&reg_usb0_vbus>;
status = "okay";
};
};
regulators {
compatible = "simple-bus";
reg_usb0_vbus: usb0_vbus {
compatible = "regulator-fixed";
regulator-name = "usb0_vbus";
regulator-min-microvolt = <5000000>;
regulator-max-microvolt = <5000000>;
enable-active-high;
startup-delay-us = <300>; /* LAN9215 requires a POR of 200us minimum */
gpio = <&gpio0 17 0>;
};
};
leds {
compatible = "gpio-leds";
pinctrl-names = "default";
pinctrl-0 = <&led_pin_gpio0_17>;
user {
label = "green";
gpios = <&gpio2 1 1>;
};
};
};