mirror of
https://github.com/AuxXxilium/linux_dsm_epyc7002.git
synced 2024-12-26 02:25:44 +07:00
30dd9fb924
The at24 driver allows to register I2C EEPROM chips using different vendor and devices, but the I2C subsystem does not take the vendor into account when matching using the I2C table since it only has device entries. But when matching using an OF table, both the vendor and device has to be taken into account so the driver defines only a set of compatible strings using the "atmel" vendor as a generic fallback for compatible I2C devices. So add this generic fallback to the device node compatible string to make the device to match the driver using the OF device ID table. Signed-off-by: Javier Martinez Canillas <javier@dowhile0.org> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
103 lines
2.2 KiB
Plaintext
103 lines
2.2 KiB
Plaintext
/*
|
|
* Copyright 2012 Sascha Hauer, Uwe Kleine-König, Steffen Trumtrar
|
|
* and Markus Pargmann, Pengutronix
|
|
*
|
|
* The code contained herein is licensed under the GNU General Public
|
|
* License. You may obtain a copy of the GNU General Public License
|
|
* Version 2 or later at the following locations:
|
|
*
|
|
* http://www.opensource.org/licenses/gpl-license.html
|
|
* http://www.gnu.org/copyleft/gpl.html
|
|
*/
|
|
|
|
/dts-v1/;
|
|
#include "imx27.dtsi"
|
|
|
|
/ {
|
|
model = "Phytec pca100";
|
|
compatible = "phytec,imx27-pca100", "fsl,imx27";
|
|
|
|
memory {
|
|
reg = <0xa0000000 0x08000000>; /* 128MB */
|
|
};
|
|
};
|
|
|
|
&cspi1 {
|
|
cs-gpios = <&gpio4 28 GPIO_ACTIVE_HIGH>,
|
|
<&gpio4 27 GPIO_ACTIVE_HIGH>;
|
|
status = "okay";
|
|
};
|
|
|
|
&fec {
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&pinctrl_fec1>;
|
|
status = "okay";
|
|
};
|
|
|
|
&i2c2 {
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&pinctrl_i2c2>;
|
|
status = "okay";
|
|
|
|
at24@52 {
|
|
compatible = "atmel,24c32";
|
|
pagesize = <32>;
|
|
reg = <0x52>;
|
|
};
|
|
};
|
|
|
|
&iomuxc {
|
|
imx27-phycard-s-som {
|
|
pinctrl_fec1: fec1grp {
|
|
fsl,pins = <
|
|
MX27_PAD_SD3_CMD__FEC_TXD0 0x0
|
|
MX27_PAD_SD3_CLK__FEC_TXD1 0x0
|
|
MX27_PAD_ATA_DATA0__FEC_TXD2 0x0
|
|
MX27_PAD_ATA_DATA1__FEC_TXD3 0x0
|
|
MX27_PAD_ATA_DATA2__FEC_RX_ER 0x0
|
|
MX27_PAD_ATA_DATA3__FEC_RXD1 0x0
|
|
MX27_PAD_ATA_DATA4__FEC_RXD2 0x0
|
|
MX27_PAD_ATA_DATA5__FEC_RXD3 0x0
|
|
MX27_PAD_ATA_DATA6__FEC_MDIO 0x0
|
|
MX27_PAD_ATA_DATA7__FEC_MDC 0x0
|
|
MX27_PAD_ATA_DATA8__FEC_CRS 0x0
|
|
MX27_PAD_ATA_DATA9__FEC_TX_CLK 0x0
|
|
MX27_PAD_ATA_DATA10__FEC_RXD0 0x0
|
|
MX27_PAD_ATA_DATA11__FEC_RX_DV 0x0
|
|
MX27_PAD_ATA_DATA12__FEC_RX_CLK 0x0
|
|
MX27_PAD_ATA_DATA13__FEC_COL 0x0
|
|
MX27_PAD_ATA_DATA14__FEC_TX_ER 0x0
|
|
MX27_PAD_ATA_DATA15__FEC_TX_EN 0x0
|
|
>;
|
|
};
|
|
|
|
pinctrl_i2c2: i2c2grp {
|
|
fsl,pins = <
|
|
MX27_PAD_I2C2_SDA__I2C2_SDA 0x0
|
|
MX27_PAD_I2C2_SCL__I2C2_SCL 0x0
|
|
>;
|
|
};
|
|
|
|
pinctrl_nfc: nfcgrp {
|
|
fsl,pins = <
|
|
MX27_PAD_NFRB__NFRB 0x0
|
|
MX27_PAD_NFCLE__NFCLE 0x0
|
|
MX27_PAD_NFWP_B__NFWP_B 0x0
|
|
MX27_PAD_NFCE_B__NFCE_B 0x0
|
|
MX27_PAD_NFALE__NFALE 0x0
|
|
MX27_PAD_NFRE_B__NFRE_B 0x0
|
|
MX27_PAD_NFWE_B__NFWE_B 0x0
|
|
>;
|
|
};
|
|
};
|
|
};
|
|
|
|
&nfc {
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&pinctrl_nfc>;
|
|
nand-bus-width = <8>;
|
|
nand-ecc-mode = "hw";
|
|
nand-on-flash-bbt;
|
|
status = "okay";
|
|
};
|