Arnd Bergmann 025792ca72 Merge tag 'renesas-arm64-dt-for-v4.15' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/soc ... Pull "Renesas ARM64 Based SoC DT Updates for v4.15" from Simon Horman: * r8a7795 (H3) - Use r8a7795-cpg-mssr and r8a7795-sysc bindings Hardcoded indicies are replaced with symbols now that they are available - Drop bogus HDMI node name suffixes Laurent Pinchart says: Node names should not use numerical suffixes if the nodes can be distinguished by unit-address - Update PFC node name to pin-controller Shimoda-san says the PFC node name is changed "from e6060000.pfc and pfc@e6060000 to e6060000.pin-controller and pin-controller@e6060000 like other Renesas SoCs." * r8a7795 (H3) ES1.0 - Drop extra zero from XHCI unit address This corrects a typo were ee0400000 rather than ee040000 was used as the unit address. * r8a7796 (M3-W) - Add FDP1 instance Laurent Pinchart says: The r8a7796 has a single FDP1 instance. * r8a7795 (H3) and r8a7796 (M3-W) SoCs - Add USB3.0 peripheral device nodes Shimoda-san says that this is not enabled on the Salvator-X/XS boards for now as: + we need a special cable (USB type-A to A cross cable). + we can swap the role by renesas_usb3 driver even if we use a normal cable and after usb3.0 host is running, but I think it's a special use case. * r8a7795 (H3) and r8a7796 (M3-W) ULCB boards - Enable display output Laurent Pinchart says: The DU is already wired up to the HDMI encoder, all we need to do is enable it. * r8a77995 (D3) Draak board - Enable EthernetAVB and , USB2.0 Host and PHY - Add serial console pins. This is safe to do now that r8a77995 PFC driver support is present * r8a77970 (V3M) - Add basic support for SoC and EtherAVB, [H]SCIF and SYS-DMAC nodes This is a step towards enabling EtherAVB and [H]SCIF with SYS-DMAC in the Eagle board support for which is under review * tag 'renesas-arm64-dt-for-v4.15' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas: (22 commits) arm64: dts: renesas: r8a7796: add USB3.0 peripheral device node arm64: dts: renesas: r8a7795: add USB3.0 peripheral device node arm64: dts: renesas: r8a77995: draak: enable EthernetAVB arm64: dts: renesas: r8a77995: draak: enable USB2.0 Host (EHCI/OHCI) arm64: dts: renesas: r8a77995: draak: enable USB2.0 PHY arm64: dts: renesas: r8a77995: add USB2.0 Host (EHCI/OHCI) device node arm64: dts: renesas: r8a77995: Add USB2.0 PHY device node arm64: dts: draak: Add serial console pins arm64: dts: renesas: r8a77970: add EtherAVB support arm64: dts: renesas: r8a77970: add [H]SCIF support arm64: dts: renesas: r8a77970: add SYS-DMAC support arm64: dts: renesas: initial R8A77970 SoC device tree arm64: dts: renesas: r8a77995: Add EthernetAVB device node arm64: dts: renesas: r8a77995: add GPIO device nodes arm64: dts: renesas: r8a77995: Use r8a7795-cpg-mssr binding definitions arm64: dts: renesas: r8a77995: Use r8a7795-sysc binding definitions arm64: renesas: Add Renesas R8A77970 Kconfig support arm64: dts: renesas: r8a7795: Drop bogus HDMI node names suffixes arm64: dts: renesas: ulcb: Enable display output arm64: dts: renesas: r8a77995: update PFC node name to pin-controller ...		2017-10-20 00:37:59 +02:00
..
dts	Merge tag 'renesas-arm64-dt-for-v4.15' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/soc	2017-10-20 00:37:59 +02:00
.gitignore	arm64: Build infrastructure	2012-09-17 13:42:21 +01:00
install.sh	arm64: kbuild: make "make install" not depend on vmlinux	2016-02-19 10:33:35 +00:00
Makefile	arm64: localise Image objcopy flags	2016-07-19 15:30:23 +01:00