linux_dsm_epyc7002/arch/arm/boot/dts/omap4-sdp.dts
Russell King - ARM Linux 84fb6c7feb ARM: dts: Fix OMAP4430 SDP Ethernet startup
It was noticed that unbinding and rebinding the KSZ8851 ethernet
resulted in the driver reporting "failed to read device ID" at probe.
Probing the reset line with a 'scope while repeatedly attempting to
bind the driver in a shell loop revealed that the KSZ8851 RSTN pin is
constantly held at zero, meaning the device is held in reset, and
does not respond on the SPI bus.

Experimentation with the startup delay on the regulator set to 50ms
shows that the reset is positively released after 20ms.

Schematics for this board are not available, and the traces are buried
in the inner layers of the board which makes tracing where the RSTN pin
extremely difficult.  We can only guess that the RSTN pin is wired to a
reset generator chip driven off the ethernet supply, which fits the
observed behaviour.

Include this delay in the regulator startup delay - effectively
treating the reset as a "supply stable" indicator.

This can not be modelled as a delay in the KSZ8851 driver since the
reset generation is board specific - if the RSTN pin had been wired to
a GPIO, reset could be released earlier via the already provided support
in the KSZ8851 driver.

This also got confirmed by Peter Ujfalusi <peter.ujfalusi@ti.com> based
on Blaze schematics that should be very close to SDP4430:

TPS22902YFPR is used as the regulator switch (gpio48 controlled):
Convert arm boot_lock to raw The VOUT is routed to TPS3808G01DBV.
(SCH Note: Threshold set at 90%. Vsense: 0.405V).

According to the TPS3808 data sheet the RESET delay time when Ct is
open (this is the case in the schema): MIN/TYP/MAX: 12/20/28 ms.

Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
[tony@atomide.com: updated with notes from schematics from Peter]
Signed-off-by: Tony Lindgren <tony@atomide.com>
2018-12-07 09:10:49 -08:00

706 lines
16 KiB
Plaintext

/*
* Copyright (C) 2011 Texas Instruments Incorporated - http://www.ti.com/
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*/
/dts-v1/;
#include "omap443x.dtsi"
#include "elpida_ecb240abacn.dtsi"
/ {
model = "TI OMAP4 SDP board";
compatible = "ti,omap4-sdp", "ti,omap4430", "ti,omap4";
memory@80000000 {
device_type = "memory";
reg = <0x80000000 0x40000000>; /* 1 GB */
};
aliases {
display0 = &lcd0;
display1 = &lcd1;
display2 = &hdmi0;
};
vdd_eth: fixedregulator-vdd-eth {
compatible = "regulator-fixed";
regulator-name = "VDD_ETH";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
gpio = <&gpio2 16 GPIO_ACTIVE_HIGH>; /* gpio line 48 */
enable-active-high;
regulator-boot-on;
startup-delay-us = <25000>;
};
vbat: fixedregulator-vbat {
compatible = "regulator-fixed";
regulator-name = "VBAT";
regulator-min-microvolt = <3750000>;
regulator-max-microvolt = <3750000>;
regulator-boot-on;
};
leds {
compatible = "gpio-leds";
debug0 {
label = "omap4:green:debug0";
gpios = <&gpio2 29 GPIO_ACTIVE_HIGH>; /* 61 */
};
debug1 {
label = "omap4:green:debug1";
gpios = <&gpio1 30 GPIO_ACTIVE_HIGH>; /* 30 */
};
debug2 {
label = "omap4:green:debug2";
gpios = <&gpio1 7 GPIO_ACTIVE_HIGH>; /* 7 */
};
debug3 {
label = "omap4:green:debug3";
gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>; /* 8 */
};
debug4 {
label = "omap4:green:debug4";
gpios = <&gpio2 18 GPIO_ACTIVE_HIGH>; /* 50 */
};
user1 {
label = "omap4:blue:user";
gpios = <&gpio6 9 GPIO_ACTIVE_HIGH>; /* 169 */
};
user2 {
label = "omap4:red:user";
gpios = <&gpio6 10 GPIO_ACTIVE_HIGH>; /* 170 */
};
user3 {
label = "omap4:green:user";
gpios = <&gpio5 11 GPIO_ACTIVE_HIGH>; /* 139 */
};
};
pwmleds {
compatible = "pwm-leds";
kpad {
label = "omap4::keypad";
pwms = <&twl_pwm 0 7812500>;
max-brightness = <127>;
};
charging {
label = "omap4:green:chrg";
pwms = <&twl_pwmled 0 7812500>;
max-brightness = <255>;
};
};
backlight {
compatible = "pwm-backlight";
pwms = <&twl_pwm 1 7812500>;
brightness-levels = <
0 10 20 30 40
50 60 70 80 90
100 110 120 127
>;
default-brightness-level = <13>;
};
sound {
compatible = "ti,abe-twl6040";
ti,model = "SDP4430";
ti,jack-detection = <1>;
ti,mclk-freq = <38400000>;
ti,mcpdm = <&mcpdm>;
ti,dmic = <&dmic>;
ti,twl6040 = <&twl6040>;
/* Audio routing */
ti,audio-routing =
"Headset Stereophone", "HSOL",
"Headset Stereophone", "HSOR",
"Earphone Spk", "EP",
"Ext Spk", "HFL",
"Ext Spk", "HFR",
"Line Out", "AUXL",
"Line Out", "AUXR",
"Vibrator", "VIBRAL",
"Vibrator", "VIBRAR",
"HSMIC", "Headset Mic",
"Headset Mic", "Headset Mic Bias",
"MAINMIC", "Main Handset Mic",
"Main Handset Mic", "Main Mic Bias",
"SUBMIC", "Sub Handset Mic",
"Sub Handset Mic", "Main Mic Bias",
"AFML", "Line In",
"AFMR", "Line In",
"DMic", "Digital Mic",
"Digital Mic", "Digital Mic1 Bias";
};
/* regulator for wl12xx on sdio5 */
wl12xx_vmmc: wl12xx_vmmc {
pinctrl-names = "default";
pinctrl-0 = <&wl12xx_gpio>;
compatible = "regulator-fixed";
regulator-name = "vwl1271";
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
gpio = <&gpio2 22 GPIO_ACTIVE_HIGH>;
startup-delay-us = <70000>;
enable-active-high;
};
tpd12s015: encoder {
compatible = "ti,tpd12s015";
gpios = <&gpio2 28 GPIO_ACTIVE_HIGH>, /* 60, CT CP HPD */
<&gpio2 9 GPIO_ACTIVE_HIGH>, /* 41, LS OE */
<&gpio2 31 GPIO_ACTIVE_HIGH>; /* 63, HPD */
ports {
#address-cells = <1>;
#size-cells = <0>;
port@0 {
reg = <0>;
tpd12s015_in: endpoint {
remote-endpoint = <&hdmi_out>;
};
};
port@1 {
reg = <1>;
tpd12s015_out: endpoint {
remote-endpoint = <&hdmi_connector_in>;
};
};
};
};
hdmi0: connector {
compatible = "hdmi-connector";
label = "hdmi";
type = "c";
port {
hdmi_connector_in: endpoint {
remote-endpoint = <&tpd12s015_out>;
};
};
};
};
&omap4_pmx_core {
pinctrl-names = "default";
pinctrl-0 = <
&dss_hdmi_pins
&tpd12s015_pins
>;
uart2_pins: pinmux_uart2_pins {
pinctrl-single,pins = <
OMAP4_IOPAD(0x118, PIN_INPUT_PULLUP | MUX_MODE0) /* uart2_cts.uart2_cts */
OMAP4_IOPAD(0x11a, PIN_OUTPUT | MUX_MODE0) /* uart2_rts.uart2_rts */
OMAP4_IOPAD(0x11c, PIN_INPUT_PULLUP | MUX_MODE0) /* uart2_rx.uart2_rx */
OMAP4_IOPAD(0x11e, PIN_OUTPUT | MUX_MODE0) /* uart2_tx.uart2_tx */
>;
};
uart3_pins: pinmux_uart3_pins {
pinctrl-single,pins = <
OMAP4_IOPAD(0x140, PIN_INPUT_PULLUP | MUX_MODE0) /* uart3_cts_rctx.uart3_cts_rctx */
OMAP4_IOPAD(0x142, PIN_OUTPUT | MUX_MODE0) /* uart3_rts_sd.uart3_rts_sd */
OMAP4_IOPAD(0x144, PIN_INPUT | MUX_MODE0) /* uart3_rx_irrx.uart3_rx_irrx */
OMAP4_IOPAD(0x146, PIN_OUTPUT | MUX_MODE0) /* uart3_tx_irtx.uart3_tx_irtx */
>;
};
uart4_pins: pinmux_uart4_pins {
pinctrl-single,pins = <
OMAP4_IOPAD(0x15c, PIN_INPUT | MUX_MODE0) /* uart4_rx.uart4_rx */
OMAP4_IOPAD(0x15e, PIN_OUTPUT | MUX_MODE0) /* uart4_tx.uart4_tx */
>;
};
twl6040_pins: pinmux_twl6040_pins {
pinctrl-single,pins = <
OMAP4_IOPAD(0x120, PIN_OUTPUT | MUX_MODE3) /* hdq_sio.gpio_127 */
OMAP4_IOPAD(0x1a0, PIN_INPUT | MUX_MODE0) /* sys_nirq2.sys_nirq2 */
>;
};
mcpdm_pins: pinmux_mcpdm_pins {
pinctrl-single,pins = <
OMAP4_IOPAD(0x106, PIN_INPUT_PULLDOWN | MUX_MODE0) /* abe_pdm_ul_data.abe_pdm_ul_data */
OMAP4_IOPAD(0x108, PIN_INPUT_PULLDOWN | MUX_MODE0) /* abe_pdm_dl_data.abe_pdm_dl_data */
OMAP4_IOPAD(0x10a, PIN_INPUT_PULLUP | MUX_MODE0) /* abe_pdm_frame.abe_pdm_frame */
OMAP4_IOPAD(0x10c, PIN_INPUT_PULLDOWN | MUX_MODE0) /* abe_pdm_lb_clk.abe_pdm_lb_clk */
OMAP4_IOPAD(0x10e, PIN_INPUT_PULLDOWN | MUX_MODE0) /* abe_clks.abe_clks */
>;
};
dmic_pins: pinmux_dmic_pins {
pinctrl-single,pins = <
OMAP4_IOPAD(0x110, PIN_OUTPUT | MUX_MODE0) /* abe_dmic_clk1.abe_dmic_clk1 */
OMAP4_IOPAD(0x112, PIN_INPUT | MUX_MODE0) /* abe_dmic_din1.abe_dmic_din1 */
OMAP4_IOPAD(0x114, PIN_INPUT | MUX_MODE0) /* abe_dmic_din2.abe_dmic_din2 */
OMAP4_IOPAD(0x116, PIN_INPUT | MUX_MODE0) /* abe_dmic_din3.abe_dmic_din3 */
>;
};
mcbsp1_pins: pinmux_mcbsp1_pins {
pinctrl-single,pins = <
OMAP4_IOPAD(0x0fe, PIN_INPUT | MUX_MODE0) /* abe_mcbsp1_clkx.abe_mcbsp1_clkx */
OMAP4_IOPAD(0x100, PIN_INPUT_PULLDOWN | MUX_MODE0) /* abe_mcbsp1_dr.abe_mcbsp1_dr */
OMAP4_IOPAD(0x102, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* abe_mcbsp1_dx.abe_mcbsp1_dx */
OMAP4_IOPAD(0x104, PIN_INPUT | MUX_MODE0) /* abe_mcbsp1_fsx.abe_mcbsp1_fsx */
>;
};
mcbsp2_pins: pinmux_mcbsp2_pins {
pinctrl-single,pins = <
OMAP4_IOPAD(0x0f6, PIN_INPUT | MUX_MODE0) /* abe_mcbsp2_clkx.abe_mcbsp2_clkx */
OMAP4_IOPAD(0x0f8, PIN_INPUT_PULLDOWN | MUX_MODE0) /* abe_mcbsp2_dr.abe_mcbsp2_dr */
OMAP4_IOPAD(0x0fa, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* abe_mcbsp2_dx.abe_mcbsp2_dx */
OMAP4_IOPAD(0x0fc, PIN_INPUT | MUX_MODE0) /* abe_mcbsp2_fsx.abe_mcbsp2_fsx */
>;
};
mcspi1_pins: pinmux_mcspi1_pins {
pinctrl-single,pins = <
OMAP4_IOPAD(0x132, PIN_INPUT | MUX_MODE0) /* mcspi1_clk.mcspi1_clk */
OMAP4_IOPAD(0x134, PIN_INPUT | MUX_MODE0) /* mcspi1_somi.mcspi1_somi */
OMAP4_IOPAD(0x136, PIN_INPUT | MUX_MODE0) /* mcspi1_simo.mcspi1_simo */
OMAP4_IOPAD(0x138, PIN_INPUT | MUX_MODE0) /* mcspi1_cs0.mcspi1_cs0 */
>;
};
dss_hdmi_pins: pinmux_dss_hdmi_pins {
pinctrl-single,pins = <
OMAP4_IOPAD(0x09a, PIN_INPUT | MUX_MODE0) /* hdmi_cec.hdmi_cec */
OMAP4_IOPAD(0x09c, PIN_INPUT_PULLUP | MUX_MODE0) /* hdmi_scl.hdmi_scl */
OMAP4_IOPAD(0x09e, PIN_INPUT_PULLUP | MUX_MODE0) /* hdmi_sda.hdmi_sda */
>;
};
tpd12s015_pins: pinmux_tpd12s015_pins {
pinctrl-single,pins = <
OMAP4_IOPAD(0x062, PIN_OUTPUT | MUX_MODE3) /* gpmc_a17.gpio_41 */
OMAP4_IOPAD(0x088, PIN_OUTPUT | MUX_MODE3) /* gpmc_nbe1.gpio_60 */
OMAP4_IOPAD(0x098, PIN_INPUT_PULLDOWN | MUX_MODE3) /* hdmi_hpd.gpio_63 */
>;
};
i2c1_pins: pinmux_i2c1_pins {
pinctrl-single,pins = <
OMAP4_IOPAD(0x122, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c1_scl */
OMAP4_IOPAD(0x124, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c1_sda */
>;
};
i2c2_pins: pinmux_i2c2_pins {
pinctrl-single,pins = <
OMAP4_IOPAD(0x126, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c2_scl */
OMAP4_IOPAD(0x128, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c2_sda */
>;
};
i2c3_pins: pinmux_i2c3_pins {
pinctrl-single,pins = <
OMAP4_IOPAD(0x12a, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c3_scl */
OMAP4_IOPAD(0x12c, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c3_sda */
>;
};
i2c4_pins: pinmux_i2c4_pins {
pinctrl-single,pins = <
OMAP4_IOPAD(0x12e, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c4_scl */
OMAP4_IOPAD(0x130, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c4_sda */
>;
};
/* wl12xx GPIO output for WLAN_EN */
wl12xx_gpio: pinmux_wl12xx_gpio {
pinctrl-single,pins = <
OMAP4_IOPAD(0x07c, PIN_OUTPUT | MUX_MODE3) /* gpmc_nwp.gpio_54 */
>;
};
/* wl12xx GPIO inputs and SDIO pins */
wl12xx_pins: pinmux_wl12xx_pins {
pinctrl-single,pins = <
OMAP4_IOPAD(0x07a, PIN_INPUT | MUX_MODE3) /* gpmc_ncs3.gpio_53 */
OMAP4_IOPAD(0x148, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc5_clk.sdmmc5_clk */
OMAP4_IOPAD(0x14a, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc5_cmd.sdmmc5_cmd */
OMAP4_IOPAD(0x14c, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc5_dat0.sdmmc5_dat0 */
OMAP4_IOPAD(0x14e, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc5_dat1.sdmmc5_dat1 */
OMAP4_IOPAD(0x150, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc5_dat2.sdmmc5_dat2 */
OMAP4_IOPAD(0x152, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc5_dat3.sdmmc5_dat3 */
>;
};
};
&i2c1 {
pinctrl-names = "default";
pinctrl-0 = <&i2c1_pins>;
clock-frequency = <400000>;
twl: twl@48 {
reg = <0x48>;
/* SPI = 0, IRQ# = 7, 4 = active high level-sensitive */
interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>; /* IRQ_SYS_1N cascaded to gic */
};
twl6040: twl@4b {
compatible = "ti,twl6040";
#clock-cells = <0>;
reg = <0x4b>;
pinctrl-names = "default";
pinctrl-0 = <&twl6040_pins>;
/* SPI = 0, IRQ# = 119, 4 = active high level-sensitive */
interrupts = <GIC_SPI 119 IRQ_TYPE_LEVEL_HIGH>; /* IRQ_SYS_2N cascaded to gic */
ti,audpwron-gpio = <&gpio4 31 GPIO_ACTIVE_HIGH>; /* gpio line 127 */
vio-supply = <&v1v8>;
v2v1-supply = <&v2v1>;
enable-active-high;
/* regulators for vibra motor */
vddvibl-supply = <&vbat>;
vddvibr-supply = <&vbat>;
vibra {
/* Vibra driver, motor resistance parameters */
ti,vibldrv-res = <8>;
ti,vibrdrv-res = <3>;
ti,viblmotor-res = <10>;
ti,vibrmotor-res = <10>;
};
};
};
#include "twl6030.dtsi"
#include "twl6030_omap4.dtsi"
&i2c2 {
pinctrl-names = "default";
pinctrl-0 = <&i2c2_pins>;
clock-frequency = <400000>;
};
&i2c3 {
pinctrl-names = "default";
pinctrl-0 = <&i2c3_pins>;
clock-frequency = <400000>;
/*
* Temperature Sensor
* http://www.ti.com/lit/ds/symlink/tmp105.pdf
*/
tmp105@48 {
compatible = "ti,tmp105";
reg = <0x48>;
};
/*
* Ambient Light Sensor
* http://www.rohm.com/products/databook/sensor/pdf/bh1780gli-e.pdf
*/
bh1780@29 {
compatible = "rohm,bh1780";
reg = <0x29>;
};
};
&i2c4 {
pinctrl-names = "default";
pinctrl-0 = <&i2c4_pins>;
clock-frequency = <400000>;
/*
* 3-Axis Digital Compass
* http://www.sparkfun.com/datasheets/Sensors/Magneto/HMC5843.pdf
*/
hmc5843@1e {
compatible = "honeywell,hmc5843";
reg = <0x1e>;
};
};
&mcspi1 {
pinctrl-names = "default";
pinctrl-0 = <&mcspi1_pins>;
eth@0 {
compatible = "ks8851";
spi-max-frequency = <24000000>;
reg = <0>;
interrupt-parent = <&gpio2>;
interrupts = <2 IRQ_TYPE_LEVEL_LOW>; /* gpio line 34 */
vdd-supply = <&vdd_eth>;
};
};
&mmc1 {
vmmc-supply = <&vmmc>;
bus-width = <8>;
};
&mmc2 {
vmmc-supply = <&vaux1>;
bus-width = <8>;
ti,non-removable;
};
&mmc3 {
status = "disabled";
};
&mmc4 {
status = "disabled";
};
&mmc5 {
pinctrl-names = "default";
pinctrl-0 = <&wl12xx_pins>;
vmmc-supply = <&wl12xx_vmmc>;
non-removable;
bus-width = <4>;
cap-power-off-card;
#address-cells = <1>;
#size-cells = <0>;
wlcore: wlcore@2 {
compatible = "ti,wl1281";
reg = <2>;
interrupt-parent = <&gpio1>;
interrupts = <21 IRQ_TYPE_EDGE_RISING>; /* gpio 53 */
ref-clock-frequency = <26000000>;
tcxo-clock-frequency = <26000000>;
};
};
&emif1 {
cs1-used;
device-handle = <&elpida_ECB240ABACN>;
};
&emif2 {
cs1-used;
device-handle = <&elpida_ECB240ABACN>;
};
&keypad {
keypad,num-rows = <8>;
keypad,num-columns = <8>;
linux,keymap = <0x00000012 /* KEY_E */
0x00010013 /* KEY_R */
0x00020014 /* KEY_T */
0x00030066 /* KEY_HOME */
0x0004003f /* KEY_F5 */
0x000500f0 /* KEY_UNKNOWN */
0x00060017 /* KEY_I */
0x0007002a /* KEY_LEFTSHIFT */
0x01000020 /* KEY_D*/
0x01010021 /* KEY_F */
0x01020022 /* KEY_G */
0x010300e7 /* KEY_SEND */
0x01040040 /* KEY_F6 */
0x010500f0 /* KEY_UNKNOWN */
0x01060025 /* KEY_K */
0x0107001c /* KEY_ENTER */
0x0200002d /* KEY_X */
0x0201002e /* KEY_C */
0x0202002f /* KEY_V */
0x0203006b /* KEY_END */
0x02040041 /* KEY_F7 */
0x020500f0 /* KEY_UNKNOWN */
0x02060034 /* KEY_DOT */
0x0207003a /* KEY_CAPSLOCK */
0x0300002c /* KEY_Z */
0x0301004e /* KEY_KPLUS */
0x03020030 /* KEY_B */
0x0303003b /* KEY_F1 */
0x03040042 /* KEY_F8 */
0x030500f0 /* KEY_UNKNOWN */
0x03060018 /* KEY_O */
0x03070039 /* KEY_SPACE */
0x04000011 /* KEY_W */
0x04010015 /* KEY_Y */
0x04020016 /* KEY_U */
0x0403003c /* KEY_F2 */
0x04040073 /* KEY_VOLUMEUP */
0x040500f0 /* KEY_UNKNOWN */
0x04060026 /* KEY_L */
0x04070069 /* KEY_LEFT */
0x0500001f /* KEY_S */
0x05010023 /* KEY_H */
0x05020024 /* KEY_J */
0x0503003d /* KEY_F3 */
0x05040043 /* KEY_F9 */
0x05050072 /* KEY_VOLUMEDOWN */
0x05060032 /* KEY_M */
0x0507006a /* KEY_RIGHT */
0x06000010 /* KEY_Q */
0x0601001e /* KEY_A */
0x06020031 /* KEY_N */
0x0603009e /* KEY_BACK */
0x0604000e /* KEY_BACKSPACE */
0x060500f0 /* KEY_UNKNOWN */
0x06060019 /* KEY_P */
0x06070067 /* KEY_UP */
0x07000094 /* KEY_PROG1 */
0x07010095 /* KEY_PROG2 */
0x070200ca /* KEY_PROG3 */
0x070300cb /* KEY_PROG4 */
0x0704003e /* KEY_F4 */
0x070500f0 /* KEY_UNKNOWN */
0x07060160 /* KEY_OK */
0x0707006c>; /* KEY_DOWN */
linux,input-no-autorepeat;
};
&uart2 {
interrupts-extended = <&wakeupgen GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH
&omap4_pmx_core OMAP4_UART2_RX>;
pinctrl-names = "default";
pinctrl-0 = <&uart2_pins>;
};
&uart3 {
interrupts-extended = <&wakeupgen GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH
&omap4_pmx_core OMAP4_UART3_RX>;
pinctrl-names = "default";
pinctrl-0 = <&uart3_pins>;
};
&uart4 {
interrupts-extended = <&wakeupgen GIC_SPI 70 IRQ_TYPE_LEVEL_HIGH
&omap4_pmx_core OMAP4_UART4_RX>;
pinctrl-names = "default";
pinctrl-0 = <&uart4_pins>;
};
&mcbsp1 {
pinctrl-names = "default";
pinctrl-0 = <&mcbsp1_pins>;
status = "okay";
};
&mcbsp2 {
pinctrl-names = "default";
pinctrl-0 = <&mcbsp2_pins>;
status = "okay";
};
&dmic {
pinctrl-names = "default";
pinctrl-0 = <&dmic_pins>;
status = "okay";
};
&mcpdm {
pinctrl-names = "default";
pinctrl-0 = <&mcpdm_pins>;
clocks = <&twl6040>;
clock-names = "pdmclk";
status = "okay";
};
&twl_usb_comparator {
usb-supply = <&vusb>;
};
&usb_otg_hs {
interface-type = <1>;
mode = <3>;
power = <50>;
};
&dss {
status = "ok";
};
&dsi1 {
status = "ok";
vdd-supply = <&vcxio>;
port {
dsi1_out_ep: endpoint {
remote-endpoint = <&lcd0_in>;
lanes = <0 1 2 3 4 5>;
};
};
lcd0: display {
compatible = "tpo,taal", "panel-dsi-cm";
label = "lcd0";
reset-gpios = <&gpio4 6 GPIO_ACTIVE_HIGH>; /* 102 */
port {
lcd0_in: endpoint {
remote-endpoint = <&dsi1_out_ep>;
};
};
};
};
&dsi2 {
status = "ok";
vdd-supply = <&vcxio>;
port {
dsi2_out_ep: endpoint {
remote-endpoint = <&lcd1_in>;
lanes = <0 1 2 3 4 5>;
};
};
lcd1: display {
compatible = "tpo,taal", "panel-dsi-cm";
label = "lcd1";
reset-gpios = <&gpio4 8 GPIO_ACTIVE_HIGH>; /* 104 */
port {
lcd1_in: endpoint {
remote-endpoint = <&dsi2_out_ep>;
};
};
};
};
&hdmi {
status = "ok";
vdda-supply = <&vdac>;
port {
hdmi_out: endpoint {
remote-endpoint = <&tpd12s015_in>;
};
};
};