mirror of
https://github.com/AuxXxilium/linux_dsm_epyc7002.git
synced 2024-12-22 19:54:40 +07:00
7b8f80d0ca
Update the nand flash binding to the new style. Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz> Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
119 lines
2.4 KiB
Plaintext
119 lines
2.4 KiB
Plaintext
// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
|
|
/*
|
|
* Device Tree file for DB-DXBC2 board
|
|
*
|
|
* Copyright (C) 2016 Allied Telesis Labs
|
|
*
|
|
* Based on armada-xp-db.dts
|
|
*
|
|
* Note: this Device Tree assumes that the bootloader has remapped the
|
|
* internal registers to 0xf1000000 (instead of the default
|
|
* 0xd0000000). The 0xf1000000 is the default used by the recent,
|
|
* DT-capable, U-Boot bootloaders provided by Marvell. Some earlier
|
|
* boards were delivered with an older version of the bootloader that
|
|
* left internal registers mapped at 0xd0000000. If you are in this
|
|
* situation, you should either update your bootloader (preferred
|
|
* solution) or the below Device Tree should be adjusted.
|
|
*/
|
|
|
|
/dts-v1/;
|
|
#include "armada-xp-98dx4251.dtsi"
|
|
|
|
/ {
|
|
model = "Marvell Bobcat2 Evaluation Board";
|
|
compatible = "marvell,db-dxbc2", "marvell,armadaxp-98dx4251", "marvell,armada-370-xp";
|
|
|
|
chosen {
|
|
bootargs = "console=ttyS0,115200 earlyprintk";
|
|
};
|
|
|
|
memory {
|
|
device_type = "memory";
|
|
reg = <0 0x00000000 0 0x20000000>; /* 512 MB */
|
|
};
|
|
|
|
};
|
|
|
|
&devbus_bootcs {
|
|
status = "okay";
|
|
|
|
/* Device Bus parameters are required */
|
|
|
|
/* Read parameters */
|
|
devbus,bus-width = <16>;
|
|
devbus,turn-off-ps = <60000>;
|
|
devbus,badr-skew-ps = <0>;
|
|
devbus,acc-first-ps = <124000>;
|
|
devbus,acc-next-ps = <248000>;
|
|
devbus,rd-setup-ps = <0>;
|
|
devbus,rd-hold-ps = <0>;
|
|
|
|
/* Write parameters */
|
|
devbus,sync-enable = <0>;
|
|
devbus,wr-high-ps = <60000>;
|
|
devbus,wr-low-ps = <60000>;
|
|
devbus,ale-wr-ps = <60000>;
|
|
};
|
|
|
|
&i2c0 {
|
|
clock-frequency = <100000>;
|
|
status = "okay";
|
|
};
|
|
|
|
&uart0 {
|
|
status = "okay";
|
|
};
|
|
|
|
&uart1 {
|
|
status = "okay";
|
|
};
|
|
|
|
&nand_controller {
|
|
status = "okay";
|
|
|
|
nand@0 {
|
|
reg = <0>;
|
|
label = "pxa3xx_nand-0";
|
|
nand-rb = <0>;
|
|
marvell,nand-keep-config;
|
|
nand-on-flash-bbt;
|
|
nand-ecc-strength = <4>;
|
|
nand-ecc-step-size = <512>;
|
|
};
|
|
};
|
|
|
|
&sdio {
|
|
pinctrl-0 = <&sdio_pins>;
|
|
pinctrl-names = "default";
|
|
status = "okay";
|
|
/* No CD or WP GPIOs */
|
|
broken-cd;
|
|
};
|
|
|
|
&spi0 {
|
|
status = "okay";
|
|
|
|
spi-flash@0 {
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
compatible = "m25p64";
|
|
reg = <0>; /* Chip select 0 */
|
|
spi-max-frequency = <20000000>;
|
|
m25p,fast-read;
|
|
|
|
partition@u-boot {
|
|
reg = <0x00000000 0x00100000>;
|
|
label = "u-boot";
|
|
};
|
|
partition@u-boot-env {
|
|
reg = <0x00100000 0x00040000>;
|
|
label = "u-boot-env";
|
|
};
|
|
partition@unused {
|
|
reg = <0x00140000 0x00ec0000>;
|
|
label = "unused";
|
|
};
|
|
|
|
};
|
|
};
|