/* * Copyright (C) 2005, 2006 IBM Corporation * Copyright (C) 2014, 2015 Intel Corporation * * Authors: * Leendert van Doorn * Kylene Hall * * Maintained by: * * Device driver for TCG/TCPA TPM (trusted platform module). * Specifications at www.trustedcomputinggroup.org * * This device driver implements the TPM interface as defined in * the TCG TPM Interface Spec version 1.2, revision 1.0. * * This program is free software; you can redistribute it and/or * modify it under the terms of the GNU General Public License as * published by the Free Software Foundation, version 2 of the * License. */ #include #include #include #include #include #include #include #include #include #include #include "tpm.h" enum tis_access { TPM_ACCESS_VALID = 0x80, TPM_ACCESS_ACTIVE_LOCALITY = 0x20, TPM_ACCESS_REQUEST_PENDING = 0x04, TPM_ACCESS_REQUEST_USE = 0x02, }; enum tis_status { TPM_STS_VALID = 0x80, TPM_STS_COMMAND_READY = 0x40, TPM_STS_GO = 0x20, TPM_STS_DATA_AVAIL = 0x10, TPM_STS_DATA_EXPECT = 0x08, }; enum tis_int_flags { TPM_GLOBAL_INT_ENABLE = 0x80000000, TPM_INTF_BURST_COUNT_STATIC = 0x100, TPM_INTF_CMD_READY_INT = 0x080, TPM_INTF_INT_EDGE_FALLING = 0x040, TPM_INTF_INT_EDGE_RISING = 0x020, TPM_INTF_INT_LEVEL_LOW = 0x010, TPM_INTF_INT_LEVEL_HIGH = 0x008, TPM_INTF_LOCALITY_CHANGE_INT = 0x004, TPM_INTF_STS_VALID_INT = 0x002, TPM_INTF_DATA_AVAIL_INT = 0x001, }; enum tis_defaults { TIS_MEM_BASE = 0xFED40000, TIS_MEM_LEN = 0x5000, TIS_SHORT_TIMEOUT = 750, /* ms */ TIS_LONG_TIMEOUT = 2000, /* 2 sec */ }; struct tpm_info { unsigned long start; unsigned long len; unsigned int irq; }; static struct tpm_info tis_default_info = { .start = TIS_MEM_BASE, .len = TIS_MEM_LEN, .irq = 0, }; /* Some timeout values are needed before it is known whether the chip is * TPM 1.0 or TPM 2.0. */ #define TIS_TIMEOUT_A_MAX max(TIS_SHORT_TIMEOUT, TPM2_TIMEOUT_A) #define TIS_TIMEOUT_B_MAX max(TIS_LONG_TIMEOUT, TPM2_TIMEOUT_B) #define TIS_TIMEOUT_C_MAX max(TIS_SHORT_TIMEOUT, TPM2_TIMEOUT_C) #define TIS_TIMEOUT_D_MAX max(TIS_SHORT_TIMEOUT, TPM2_TIMEOUT_D) #define TPM_ACCESS(l) (0x0000 | ((l) << 12)) #define TPM_INT_ENABLE(l) (0x0008 | ((l) << 12)) #define TPM_INT_VECTOR(l) (0x000C | ((l) << 12)) #define TPM_INT_STATUS(l) (0x0010 | ((l) << 12)) #define TPM_INTF_CAPS(l) (0x0014 | ((l) << 12)) #define TPM_STS(l) (0x0018 | ((l) << 12)) #define TPM_STS3(l) (0x001b | ((l) << 12)) #define TPM_DATA_FIFO(l) (0x0024 | ((l) << 12)) #define TPM_DID_VID(l) (0x0F00 | ((l) << 12)) #define TPM_RID(l) (0x0F04 | ((l) << 12)) struct priv_data { bool irq_tested; }; #if defined(CONFIG_PNP) && defined(CONFIG_ACPI) static int has_hid(struct acpi_device *dev, const char *hid) { struct acpi_hardware_id *id; list_for_each_entry(id, &dev->pnp.ids, list) if (!strcmp(hid, id->id)) return 1; return 0; } static inline int is_itpm(struct acpi_device *dev) { return has_hid(dev, "INTC0102"); } static inline int is_fifo(struct acpi_device *dev) { struct acpi_table_tpm2 *tbl; acpi_status st; /* TPM 1.2 FIFO */ if (!has_hid(dev, "MSFT0101")) return 1; st = acpi_get_table(ACPI_SIG_TPM2, 1, (struct acpi_table_header **) &tbl); if (ACPI_FAILURE(st)) { dev_err(&dev->dev, "failed to get TPM2 ACPI table\n"); return 0; } if (le32_to_cpu(tbl->start_method) != TPM2_START_FIFO) return 0; /* TPM 2.0 FIFO */ return 1; } #else static inline int is_itpm(struct acpi_device *dev) { return 0; } static inline int is_fifo(struct acpi_device *dev) { return 1; } #endif /* Before we attempt to access the TPM we must see that the valid bit is set. * The specification says that this bit is 0 at reset and remains 0 until the * 'TPM has gone through its self test and initialization and has established * correct values in the other bits.' */ static int wait_startup(struct tpm_chip *chip, int l) { unsigned long stop = jiffies + chip->vendor.timeout_a; do { if (ioread8(chip->vendor.iobase + TPM_ACCESS(l)) & TPM_ACCESS_VALID) return 0; msleep(TPM_TIMEOUT); } while (time_before(jiffies, stop)); return -1; } static int check_locality(struct tpm_chip *chip, int l) { if ((ioread8(chip->vendor.iobase + TPM_ACCESS(l)) & (TPM_ACCESS_ACTIVE_LOCALITY | TPM_ACCESS_VALID)) == (TPM_ACCESS_ACTIVE_LOCALITY | TPM_ACCESS_VALID)) return chip->vendor.locality = l; return -1; } static void release_locality(struct tpm_chip *chip, int l, int force) { if (force || (ioread8(chip->vendor.iobase + TPM_ACCESS(l)) & (TPM_ACCESS_REQUEST_PENDING | TPM_ACCESS_VALID)) == (TPM_ACCESS_REQUEST_PENDING | TPM_ACCESS_VALID)) iowrite8(TPM_ACCESS_ACTIVE_LOCALITY, chip->vendor.iobase + TPM_ACCESS(l)); } static int request_locality(struct tpm_chip *chip, int l) { unsigned long stop, timeout; long rc; if (check_locality(chip, l) >= 0) return l; iowrite8(TPM_ACCESS_REQUEST_USE, chip->vendor.iobase + TPM_ACCESS(l)); stop = jiffies + chip->vendor.timeout_a; if (chip->vendor.irq) { again: timeout = stop - jiffies; if ((long)timeout <= 0) return -1; rc = wait_event_interruptible_timeout(chip->vendor.int_queue, (check_locality (chip, l) >= 0), timeout); if (rc > 0) return l; if (rc == -ERESTARTSYS && freezing(current)) { clear_thread_flag(TIF_SIGPENDING); goto again; } } else { /* wait for burstcount */ do { if (check_locality(chip, l) >= 0) return l; msleep(TPM_TIMEOUT); } while (time_before(jiffies, stop)); } return -1; } static u8 tpm_tis_status(struct tpm_chip *chip) { return ioread8(chip->vendor.iobase + TPM_STS(chip->vendor.locality)); } static void tpm_tis_ready(struct tpm_chip *chip) { /* this causes the current command to be aborted */ iowrite8(TPM_STS_COMMAND_READY, chip->vendor.iobase + TPM_STS(chip->vendor.locality)); } static int get_burstcount(struct tpm_chip *chip) { unsigned long stop; int burstcnt; /* wait for burstcount */ /* which timeout value, spec has 2 answers (c & d) */ stop = jiffies + chip->vendor.timeout_d; do { burstcnt = ioread8(chip->vendor.iobase + TPM_STS(chip->vendor.locality) + 1); burstcnt += ioread8(chip->vendor.iobase + TPM_STS(chip->vendor.locality) + 2) << 8; if (burstcnt) return burstcnt; msleep(TPM_TIMEOUT); } while (time_before(jiffies, stop)); return -EBUSY; } static int recv_data(struct tpm_chip *chip, u8 *buf, size_t count) { int size = 0, burstcnt; while (size < count && wait_for_tpm_stat(chip, TPM_STS_DATA_AVAIL | TPM_STS_VALID, chip->vendor.timeout_c, &chip->vendor.read_queue, true) == 0) { burstcnt = get_burstcount(chip); for (; burstcnt > 0 && size < count; burstcnt--) buf[size++] = ioread8(chip->vendor.iobase + TPM_DATA_FIFO(chip->vendor. locality)); } return size; } static int tpm_tis_recv(struct tpm_chip *chip, u8 *buf, size_t count) { int size = 0; int expected, status; if (count < TPM_HEADER_SIZE) { size = -EIO; goto out; } /* read first 10 bytes, including tag, paramsize, and result */ if ((size = recv_data(chip, buf, TPM_HEADER_SIZE)) < TPM_HEADER_SIZE) { dev_err(chip->pdev, "Unable to read header\n"); goto out; } expected = be32_to_cpu(*(__be32 *) (buf + 2)); if (expected > count) { size = -EIO; goto out; } if ((size += recv_data(chip, &buf[TPM_HEADER_SIZE], expected - TPM_HEADER_SIZE)) < expected) { dev_err(chip->pdev, "Unable to read remainder of result\n"); size = -ETIME; goto out; } wait_for_tpm_stat(chip, TPM_STS_VALID, chip->vendor.timeout_c, &chip->vendor.int_queue, false); status = tpm_tis_status(chip); if (status & TPM_STS_DATA_AVAIL) { /* retry? */ dev_err(chip->pdev, "Error left over data\n"); size = -EIO; goto out; } out: tpm_tis_ready(chip); release_locality(chip, chip->vendor.locality, 0); return size; } static bool itpm; module_param(itpm, bool, 0444); MODULE_PARM_DESC(itpm, "Force iTPM workarounds (found on some Lenovo laptops)"); /* * If interrupts are used (signaled by an irq set in the vendor structure) * tpm.c can skip polling for the data to be available as the interrupt is * waited for here */ static int tpm_tis_send_data(struct tpm_chip *chip, u8 *buf, size_t len) { int rc, status, burstcnt; size_t count = 0; if (request_locality(chip, 0) < 0) return -EBUSY; status = tpm_tis_status(chip); if ((status & TPM_STS_COMMAND_READY) == 0) { tpm_tis_ready(chip); if (wait_for_tpm_stat (chip, TPM_STS_COMMAND_READY, chip->vendor.timeout_b, &chip->vendor.int_queue, false) < 0) { rc = -ETIME; goto out_err; } } while (count < len - 1) { burstcnt = get_burstcount(chip); for (; burstcnt > 0 && count < len - 1; burstcnt--) { iowrite8(buf[count], chip->vendor.iobase + TPM_DATA_FIFO(chip->vendor.locality)); count++; } wait_for_tpm_stat(chip, TPM_STS_VALID, chip->vendor.timeout_c, &chip->vendor.int_queue, false); status = tpm_tis_status(chip); if (!itpm && (status & TPM_STS_DATA_EXPECT) == 0) { rc = -EIO; goto out_err; } } /* write last byte */ iowrite8(buf[count], chip->vendor.iobase + TPM_DATA_FIFO(chip->vendor.locality)); wait_for_tpm_stat(chip, TPM_STS_VALID, chip->vendor.timeout_c, &chip->vendor.int_queue, false); status = tpm_tis_status(chip); if ((status & TPM_STS_DATA_EXPECT) != 0) { rc = -EIO; goto out_err; } return 0; out_err: tpm_tis_ready(chip); release_locality(chip, chip->vendor.locality, 0); return rc; } static void disable_interrupts(struct tpm_chip *chip) { u32 intmask; intmask = ioread32(chip->vendor.iobase + TPM_INT_ENABLE(chip->vendor.locality)); intmask &= ~TPM_GLOBAL_INT_ENABLE; iowrite32(intmask, chip->vendor.iobase + TPM_INT_ENABLE(chip->vendor.locality)); devm_free_irq(chip->pdev, chip->vendor.irq, chip); chip->vendor.irq = 0; } /* * If interrupts are used (signaled by an irq set in the vendor structure) * tpm.c can skip polling for the data to be available as the interrupt is * waited for here */ static int tpm_tis_send_main(struct tpm_chip *chip, u8 *buf, size_t len) { int rc; u32 ordinal; unsigned long dur; rc = tpm_tis_send_data(chip, buf, len); if (rc < 0) return rc; /* go and do it */ iowrite8(TPM_STS_GO, chip->vendor.iobase + TPM_STS(chip->vendor.locality)); if (chip->vendor.irq) { ordinal = be32_to_cpu(*((__be32 *) (buf + 6))); if (chip->flags & TPM_CHIP_FLAG_TPM2) dur = tpm2_calc_ordinal_duration(chip, ordinal); else dur = tpm_calc_ordinal_duration(chip, ordinal); if (wait_for_tpm_stat (chip, TPM_STS_DATA_AVAIL | TPM_STS_VALID, dur, &chip->vendor.read_queue, false) < 0) { rc = -ETIME; goto out_err; } } return len; out_err: tpm_tis_ready(chip); release_locality(chip, chip->vendor.locality, 0); return rc; } static int tpm_tis_send(struct tpm_chip *chip, u8 *buf, size_t len) { int rc, irq; struct priv_data *priv = chip->vendor.priv; if (!chip->vendor.irq || priv->irq_tested) return tpm_tis_send_main(chip, buf, len); /* Verify receipt of the expected IRQ */ irq = chip->vendor.irq; chip->vendor.irq = 0; rc = tpm_tis_send_main(chip, buf, len); chip->vendor.irq = irq; if (!priv->irq_tested) msleep(1); if (!priv->irq_tested) disable_interrupts(chip); priv->irq_tested = true; return rc; } struct tis_vendor_timeout_override { u32 did_vid; unsigned long timeout_us[4]; }; static const struct tis_vendor_timeout_override vendor_timeout_overrides[] = { /* Atmel 3204 */ { 0x32041114, { (TIS_SHORT_TIMEOUT*1000), (TIS_LONG_TIMEOUT*1000), (TIS_SHORT_TIMEOUT*1000), (TIS_SHORT_TIMEOUT*1000) } }, }; static bool tpm_tis_update_timeouts(struct tpm_chip *chip, unsigned long *timeout_cap) { int i; u32 did_vid; did_vid = ioread32(chip->vendor.iobase + TPM_DID_VID(0)); for (i = 0; i != ARRAY_SIZE(vendor_timeout_overrides); i++) { if (vendor_timeout_overrides[i].did_vid != did_vid) continue; memcpy(timeout_cap, vendor_timeout_overrides[i].timeout_us, sizeof(vendor_timeout_overrides[i].timeout_us)); return true; } return false; } /* * Early probing for iTPM with STS_DATA_EXPECT flaw. * Try sending command without itpm flag set and if that * fails, repeat with itpm flag set. */ static int probe_itpm(struct tpm_chip *chip) { int rc = 0; u8 cmd_getticks[] = { 0x00, 0xc1, 0x00, 0x00, 0x00, 0x0a, 0x00, 0x00, 0x00, 0xf1 }; size_t len = sizeof(cmd_getticks); bool rem_itpm = itpm; u16 vendor = ioread16(chip->vendor.iobase + TPM_DID_VID(0)); /* probe only iTPMS */ if (vendor != TPM_VID_INTEL) return 0; itpm = false; rc = tpm_tis_send_data(chip, cmd_getticks, len); if (rc == 0) goto out; tpm_tis_ready(chip); release_locality(chip, chip->vendor.locality, 0); itpm = true; rc = tpm_tis_send_data(chip, cmd_getticks, len); if (rc == 0) { dev_info(chip->pdev, "Detected an iTPM.\n"); rc = 1; } else rc = -EFAULT; out: itpm = rem_itpm; tpm_tis_ready(chip); release_locality(chip, chip->vendor.locality, 0); return rc; } static bool tpm_tis_req_canceled(struct tpm_chip *chip, u8 status) { switch (chip->vendor.manufacturer_id) { case TPM_VID_WINBOND: return ((status == TPM_STS_VALID) || (status == (TPM_STS_VALID | TPM_STS_COMMAND_READY))); case TPM_VID_STM: return (status == (TPM_STS_VALID | TPM_STS_COMMAND_READY)); default: return (status == TPM_STS_COMMAND_READY); } } static const struct tpm_class_ops tpm_tis = { .status = tpm_tis_status, .recv = tpm_tis_recv, .send = tpm_tis_send, .cancel = tpm_tis_ready, .update_timeouts = tpm_tis_update_timeouts, .req_complete_mask = TPM_STS_DATA_AVAIL | TPM_STS_VALID, .req_complete_val = TPM_STS_DATA_AVAIL | TPM_STS_VALID, .req_canceled = tpm_tis_req_canceled, }; static irqreturn_t tis_int_handler(int dummy, void *dev_id) { struct tpm_chip *chip = dev_id; u32 interrupt; int i; interrupt = ioread32(chip->vendor.iobase + TPM_INT_STATUS(chip->vendor.locality)); if (interrupt == 0) return IRQ_NONE; ((struct priv_data *)chip->vendor.priv)->irq_tested = true; if (interrupt & TPM_INTF_DATA_AVAIL_INT) wake_up_interruptible(&chip->vendor.read_queue); if (interrupt & TPM_INTF_LOCALITY_CHANGE_INT) for (i = 0; i < 5; i++) if (check_locality(chip, i) >= 0) break; if (interrupt & (TPM_INTF_LOCALITY_CHANGE_INT | TPM_INTF_STS_VALID_INT | TPM_INTF_CMD_READY_INT)) wake_up_interruptible(&chip->vendor.int_queue); /* Clear interrupts handled with TPM_EOI */ iowrite32(interrupt, chip->vendor.iobase + TPM_INT_STATUS(chip->vendor.locality)); ioread32(chip->vendor.iobase + TPM_INT_STATUS(chip->vendor.locality)); return IRQ_HANDLED; } /* Register the IRQ and issue a command that will cause an interrupt. If an * irq is seen then leave the chip setup for IRQ operation, otherwise reverse * everything and leave in polling mode. Returns 0 on success. */ static int tpm_tis_probe_irq_single(struct tpm_chip *chip, u32 intmask, int irq) { struct priv_data *priv = chip->vendor.priv; u8 original_int_vec; if (devm_request_irq(chip->pdev, irq, tis_int_handler, IRQF_SHARED, chip->devname, chip) != 0) { dev_info(chip->pdev, "Unable to request irq: %d for probe\n", irq); return -1; } chip->vendor.irq = irq; original_int_vec = ioread8(chip->vendor.iobase + TPM_INT_VECTOR(chip->vendor.locality)); iowrite8(irq, chip->vendor.iobase + TPM_INT_VECTOR(chip->vendor.locality)); /* Clear all existing */ iowrite32(ioread32(chip->vendor.iobase + TPM_INT_STATUS(chip->vendor.locality)), chip->vendor.iobase + TPM_INT_STATUS(chip->vendor.locality)); /* Turn on */ iowrite32(intmask | TPM_GLOBAL_INT_ENABLE, chip->vendor.iobase + TPM_INT_ENABLE(chip->vendor.locality)); priv->irq_tested = false; /* Generate an interrupt by having the core call through to * tpm_tis_send */ if (chip->flags & TPM_CHIP_FLAG_TPM2) tpm2_gen_interrupt(chip); else tpm_gen_interrupt(chip); /* tpm_tis_send will either confirm the interrupt is working or it * will call disable_irq which undoes all of the above. */ if (!chip->vendor.irq) { iowrite8(original_int_vec, chip->vendor.iobase + TPM_INT_VECTOR(chip->vendor.locality)); return 1; } return 0; } /* Try to find the IRQ the TPM is using. This is for legacy x86 systems that * do not have ACPI/etc. We typically expect the interrupt to be declared if * present. */ static void tpm_tis_probe_irq(struct tpm_chip *chip, u32 intmask) { u8 original_int_vec; int i; original_int_vec = ioread8(chip->vendor.iobase + TPM_INT_VECTOR(chip->vendor.locality)); if (!original_int_vec) { for (i = 3; i <= 15; i++) if (!tpm_tis_probe_irq_single(chip, intmask, i)) return; } else if (!tpm_tis_probe_irq_single(chip, intmask, original_int_vec)) return; } static bool interrupts = true; module_param(interrupts, bool, 0444); MODULE_PARM_DESC(interrupts, "Enable interrupts"); static void tpm_tis_remove(struct tpm_chip *chip) { if (chip->flags & TPM_CHIP_FLAG_TPM2) tpm2_shutdown(chip, TPM2_SU_CLEAR); iowrite32(~TPM_GLOBAL_INT_ENABLE & ioread32(chip->vendor.iobase + TPM_INT_ENABLE(chip->vendor. locality)), chip->vendor.iobase + TPM_INT_ENABLE(chip->vendor.locality)); release_locality(chip, chip->vendor.locality, 1); } static int tpm_tis_init(struct device *dev, struct tpm_info *tpm_info, acpi_handle acpi_dev_handle) { u32 vendor, intfcaps, intmask; int rc, probe; struct tpm_chip *chip; struct priv_data *priv; priv = devm_kzalloc(dev, sizeof(struct priv_data), GFP_KERNEL); if (priv == NULL) return -ENOMEM; chip = tpmm_chip_alloc(dev, &tpm_tis); if (IS_ERR(chip)) return PTR_ERR(chip); chip->vendor.priv = priv; #ifdef CONFIG_ACPI chip->acpi_dev_handle = acpi_dev_handle; #endif chip->vendor.iobase = devm_ioremap(dev, tpm_info->start, tpm_info->len); if (!chip->vendor.iobase) return -EIO; /* Maximum timeouts */ chip->vendor.timeout_a = TIS_TIMEOUT_A_MAX; chip->vendor.timeout_b = TIS_TIMEOUT_B_MAX; chip->vendor.timeout_c = TIS_TIMEOUT_C_MAX; chip->vendor.timeout_d = TIS_TIMEOUT_D_MAX; if (wait_startup(chip, 0) != 0) { rc = -ENODEV; goto out_err; } /* Take control of the TPM's interrupt hardware and shut it off */ intmask = ioread32(chip->vendor.iobase + TPM_INT_ENABLE(chip->vendor.locality)); intmask |= TPM_INTF_CMD_READY_INT | TPM_INTF_LOCALITY_CHANGE_INT | TPM_INTF_DATA_AVAIL_INT | TPM_INTF_STS_VALID_INT; intmask &= ~TPM_GLOBAL_INT_ENABLE; iowrite32(intmask, chip->vendor.iobase + TPM_INT_ENABLE(chip->vendor.locality)); if (request_locality(chip, 0) != 0) { rc = -ENODEV; goto out_err; } rc = tpm2_probe(chip); if (rc) goto out_err; vendor = ioread32(chip->vendor.iobase + TPM_DID_VID(0)); chip->vendor.manufacturer_id = vendor; dev_info(dev, "%s TPM (device-id 0x%X, rev-id %d)\n", (chip->flags & TPM_CHIP_FLAG_TPM2) ? "2.0" : "1.2", vendor >> 16, ioread8(chip->vendor.iobase + TPM_RID(0))); if (!itpm) { probe = probe_itpm(chip); if (probe < 0) { rc = -ENODEV; goto out_err; } itpm = !!probe; } if (itpm) dev_info(dev, "Intel iTPM workaround enabled\n"); /* Figure out the capabilities */ intfcaps = ioread32(chip->vendor.iobase + TPM_INTF_CAPS(chip->vendor.locality)); dev_dbg(dev, "TPM interface capabilities (0x%x):\n", intfcaps); if (intfcaps & TPM_INTF_BURST_COUNT_STATIC) dev_dbg(dev, "\tBurst Count Static\n"); if (intfcaps & TPM_INTF_CMD_READY_INT) dev_dbg(dev, "\tCommand Ready Int Support\n"); if (intfcaps & TPM_INTF_INT_EDGE_FALLING) dev_dbg(dev, "\tInterrupt Edge Falling\n"); if (intfcaps & TPM_INTF_INT_EDGE_RISING) dev_dbg(dev, "\tInterrupt Edge Rising\n"); if (intfcaps & TPM_INTF_INT_LEVEL_LOW) dev_dbg(dev, "\tInterrupt Level Low\n"); if (intfcaps & TPM_INTF_INT_LEVEL_HIGH) dev_dbg(dev, "\tInterrupt Level High\n"); if (intfcaps & TPM_INTF_LOCALITY_CHANGE_INT) dev_dbg(dev, "\tLocality Change Int Support\n"); if (intfcaps & TPM_INTF_STS_VALID_INT) dev_dbg(dev, "\tSts Valid Int Support\n"); if (intfcaps & TPM_INTF_DATA_AVAIL_INT) dev_dbg(dev, "\tData Avail Int Support\n"); /* Very early on issue a command to the TPM in polling mode to make * sure it works. May as well use that command to set the proper * timeouts for the driver. */ if (tpm_get_timeouts(chip)) { dev_err(dev, "Could not get TPM timeouts and durations\n"); rc = -ENODEV; goto out_err; } /* INTERRUPT Setup */ init_waitqueue_head(&chip->vendor.read_queue); init_waitqueue_head(&chip->vendor.int_queue); if (interrupts) { if (tpm_info->irq) { tpm_tis_probe_irq_single(chip, intmask, tpm_info->irq); if (!chip->vendor.irq) dev_err(chip->pdev, FW_BUG "TPM interrupt not working, polling instead\n"); } else tpm_tis_probe_irq(chip, intmask); } if (chip->flags & TPM_CHIP_FLAG_TPM2) { rc = tpm2_do_selftest(chip); if (rc == TPM2_RC_INITIALIZE) { dev_warn(dev, "Firmware has not started TPM\n"); rc = tpm2_startup(chip, TPM2_SU_CLEAR); if (!rc) rc = tpm2_do_selftest(chip); } if (rc) { dev_err(dev, "TPM self test failed\n"); if (rc > 0) rc = -ENODEV; goto out_err; } } else { if (tpm_do_selftest(chip)) { dev_err(dev, "TPM self test failed\n"); rc = -ENODEV; goto out_err; } } return tpm_chip_register(chip); out_err: tpm_tis_remove(chip); return rc; } #ifdef CONFIG_PM_SLEEP static void tpm_tis_reenable_interrupts(struct tpm_chip *chip) { u32 intmask; /* reenable interrupts that device may have lost or BIOS/firmware may have disabled */ iowrite8(chip->vendor.irq, chip->vendor.iobase + TPM_INT_VECTOR(chip->vendor.locality)); intmask = ioread32(chip->vendor.iobase + TPM_INT_ENABLE(chip->vendor.locality)); intmask |= TPM_INTF_CMD_READY_INT | TPM_INTF_LOCALITY_CHANGE_INT | TPM_INTF_DATA_AVAIL_INT | TPM_INTF_STS_VALID_INT | TPM_GLOBAL_INT_ENABLE; iowrite32(intmask, chip->vendor.iobase + TPM_INT_ENABLE(chip->vendor.locality)); } static int tpm_tis_resume(struct device *dev) { struct tpm_chip *chip = dev_get_drvdata(dev); int ret; if (chip->vendor.irq) tpm_tis_reenable_interrupts(chip); ret = tpm_pm_resume(dev); if (ret) return ret; /* TPM 1.2 requires self-test on resume. This function actually returns * an error code but for unknown reason it isn't handled. */ if (!(chip->flags & TPM_CHIP_FLAG_TPM2)) tpm_do_selftest(chip); return 0; } #endif static SIMPLE_DEV_PM_OPS(tpm_tis_pm, tpm_pm_suspend, tpm_tis_resume); #ifdef CONFIG_PNP static int tpm_tis_pnp_init(struct pnp_dev *pnp_dev, const struct pnp_device_id *pnp_id) { struct tpm_info tpm_info = tis_default_info; acpi_handle acpi_dev_handle = NULL; tpm_info.start = pnp_mem_start(pnp_dev, 0); tpm_info.len = pnp_mem_len(pnp_dev, 0); if (pnp_irq_valid(pnp_dev, 0)) tpm_info.irq = pnp_irq(pnp_dev, 0); else interrupts = false; #ifdef CONFIG_ACPI if (pnp_acpi_device(pnp_dev)) { if (is_itpm(pnp_acpi_device(pnp_dev))) itpm = true; acpi_dev_handle = pnp_acpi_device(pnp_dev)->handle; } #endif return tpm_tis_init(&pnp_dev->dev, &tpm_info, acpi_dev_handle); } static struct pnp_device_id tpm_pnp_tbl[] = { {"PNP0C31", 0}, /* TPM */ {"ATM1200", 0}, /* Atmel */ {"IFX0102", 0}, /* Infineon */ {"BCM0101", 0}, /* Broadcom */ {"BCM0102", 0}, /* Broadcom */ {"NSC1200", 0}, /* National */ {"ICO0102", 0}, /* Intel */ /* Add new here */ {"", 0}, /* User Specified */ {"", 0} /* Terminator */ }; MODULE_DEVICE_TABLE(pnp, tpm_pnp_tbl); static void tpm_tis_pnp_remove(struct pnp_dev *dev) { struct tpm_chip *chip = pnp_get_drvdata(dev); tpm_chip_unregister(chip); tpm_tis_remove(chip); } static struct pnp_driver tis_pnp_driver = { .name = "tpm_tis", .id_table = tpm_pnp_tbl, .probe = tpm_tis_pnp_init, .remove = tpm_tis_pnp_remove, .driver = { .pm = &tpm_tis_pm, }, }; #define TIS_HID_USR_IDX sizeof(tpm_pnp_tbl)/sizeof(struct pnp_device_id) -2 module_param_string(hid, tpm_pnp_tbl[TIS_HID_USR_IDX].id, sizeof(tpm_pnp_tbl[TIS_HID_USR_IDX].id), 0444); MODULE_PARM_DESC(hid, "Set additional specific HID for this driver to probe"); #endif #ifdef CONFIG_ACPI static int tpm_check_resource(struct acpi_resource *ares, void *data) { struct tpm_info *tpm_info = (struct tpm_info *) data; struct resource res; if (acpi_dev_resource_interrupt(ares, 0, &res)) { tpm_info->irq = res.start; } else if (acpi_dev_resource_memory(ares, &res)) { tpm_info->start = res.start; tpm_info->len = resource_size(&res); } return 1; } static int tpm_tis_acpi_init(struct acpi_device *acpi_dev) { struct list_head resources; struct tpm_info tpm_info = tis_default_info; int ret; if (!is_fifo(acpi_dev)) return -ENODEV; INIT_LIST_HEAD(&resources); ret = acpi_dev_get_resources(acpi_dev, &resources, tpm_check_resource, &tpm_info); if (ret < 0) return ret; acpi_dev_free_resource_list(&resources); if (!tpm_info.irq) interrupts = false; if (is_itpm(acpi_dev)) itpm = true; return tpm_tis_init(&acpi_dev->dev, &tpm_info, acpi_dev->handle); } static int tpm_tis_acpi_remove(struct acpi_device *dev) { struct tpm_chip *chip = dev_get_drvdata(&dev->dev); tpm_chip_unregister(chip); tpm_tis_remove(chip); return 0; } static struct acpi_device_id tpm_acpi_tbl[] = { {"MSFT0101", 0}, /* TPM 2.0 */ /* Add new here */ {"", 0}, /* User Specified */ {"", 0} /* Terminator */ }; MODULE_DEVICE_TABLE(acpi, tpm_acpi_tbl); static struct acpi_driver tis_acpi_driver = { .name = "tpm_tis", .ids = tpm_acpi_tbl, .ops = { .add = tpm_tis_acpi_init, .remove = tpm_tis_acpi_remove, }, .drv = { .pm = &tpm_tis_pm, }, }; #endif static struct platform_driver tis_drv = { .driver = { .name = "tpm_tis", .pm = &tpm_tis_pm, }, }; static struct platform_device *pdev; static bool force; module_param(force, bool, 0444); MODULE_PARM_DESC(force, "Force device probe rather than using ACPI entry"); static int __init init_tis(void) { int rc; #ifdef CONFIG_PNP if (!force) { rc = pnp_register_driver(&tis_pnp_driver); if (rc) return rc; } #endif #ifdef CONFIG_ACPI if (!force) { rc = acpi_bus_register_driver(&tis_acpi_driver); if (rc) { #ifdef CONFIG_PNP pnp_unregister_driver(&tis_pnp_driver); #endif return rc; } } #endif if (!force) return 0; rc = platform_driver_register(&tis_drv); if (rc < 0) return rc; pdev = platform_device_register_simple("tpm_tis", -1, NULL, 0); if (IS_ERR(pdev)) { rc = PTR_ERR(pdev); goto err_dev; } rc = tpm_tis_init(&pdev->dev, &tis_default_info, NULL); if (rc) goto err_init; return 0; err_init: platform_device_unregister(pdev); err_dev: platform_driver_unregister(&tis_drv); return rc; } static void __exit cleanup_tis(void) { struct tpm_chip *chip; #if defined(CONFIG_PNP) || defined(CONFIG_ACPI) if (!force) { #ifdef CONFIG_ACPI acpi_bus_unregister_driver(&tis_acpi_driver); #endif #ifdef CONFIG_PNP pnp_unregister_driver(&tis_pnp_driver); #endif return; } #endif chip = dev_get_drvdata(&pdev->dev); tpm_chip_unregister(chip); tpm_tis_remove(chip); platform_device_unregister(pdev); platform_driver_unregister(&tis_drv); } module_init(init_tis); module_exit(cleanup_tis); MODULE_AUTHOR("Leendert van Doorn (leendert@watson.ibm.com)"); MODULE_DESCRIPTION("TPM Driver"); MODULE_VERSION("2.0"); MODULE_LICENSE("GPL");