Devices using an external encoder, ESD protection and level shifter
such as tpd12s015 or ip4791cz12 have the CEC pull in the encoder
chip. And on var-som-om44, there is external pull up resistor R30.
So the internal CEC pull-up resistor needs to be disabled as otherwise
the external and internal pull are parallel making the pull value
much smaller than intended. This leads into the CEC not working as
reported by Hans Verkuil <hverkuil@xs4all.nl>.
Reported-by: Hans Verkuil <hverkuil@xs4all.nl>
Cc: Dmitry Lifshitz <lifshitz@compulab.co.il>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
DDR3L is usually specified as
JEDEC standard 1.35V(1.28V~1.45V) & 1.5V(1.425V~1.575V)
Therefore setting smps6 regulator to 1.2V is definitively below
minimum. It appears that real world chips are more forgiving than
data sheets indicate, but let's set the regulator right.
Note: a board that uses other voltages (DDR with 1.5V) can
overwrite by referencing &smps6_reg.
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Reviewed-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The LEDs on igepv5 are on the GPIO expander unlike on omap5-uevm.
Configuration copied from git.isee.biz git tree except fixed for
red and blue mapping.
Signed-off-by: Tony Lindgren <tony@atomide.com>
The ID pin GPIO comes from the PMIC. Let's configure it as a GPIO
for the driver to use, and also make sure the PMIC GPIO pin muxing
is correct. The PMIC pad1 and 2 values for omap5-uevm and igepv5 are
0x5a and 0x1b, we only need to clear bit 2 in pad1 register to make
the ID pin GPIO work.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Few changes to fix issues I've noticed while debugging omap5-uevm
wl18xx issues:
1. Move wlcore irq pin muxing under wlcore. This irq could be
different from gpio_wk14 on some board variants
2. Don't configure pull on wlcore irq pin. There is a 10k
pull up resistor R105 on the device to VDDS_1v8_MAIN
3. The padconf register for wlsdio_data1 is wrong, it's really
at 0x1a8 + 2 - 0x40 = 0x16a offset, not at 0x168 as that's
for wlsdio_data0
4. Mark the omap5-uevm wlan as compatible with ti,wl1837 as
that's what the TDK R078 part seems to be
5. The MMC interrupt for WLAN musb be wakeupgen, not gic
Looks like omap5-uevm WLAN behaves better now, but I still seem
to have issues with some access points.
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch fixes the following DTC warnings for many boards:
"Node /leds/led@1 has a unit name, but no reg property"
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Device tree contents continue to be the largest branches we submit. This
time around, some of the contents worth pointing out is:
- New SoC platforms:
- Freescale i.MX 7Solo
- Broadcom BCM23550
- Cirrus Logic EP7209 and EP7211 (clps711x platforms)_
- Hisilicon HI3519
- Renesas R8A7792
Some of the other delta that is sticking out, line-count wise:
- Exynos moves of IP blocks under an SoC bus, which causes a large delta due
to indentation changes
- A new Tegra K1 board: Apalis
- A bunch of small updates to many Allwinner platforms; new hardware support,
some cleanup, etc.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJXnnckAAoJEIwa5zzehBx3Ss0P/1hp+n8DMuNCHReof8u2D3xf
pi9t5vNzfODMq/YrDT3bzQ3txoEZISt+ztEFku26BUywCZbeIEx+XLPewVEj0ODc
tpWKmW2xNZDIwn2eHRrBD5Y8gJugAnwgwBh9SqfcM8Wtdt2qc7edBvcxLhsiCTuV
pKPxPoJkan/BMR3vBMfoLIx/+aDcZJgpzUkRRuyLod17JdQ0tnMECu5UPrk6Yun8
IjDcJTcwZlpZ9gvtBhxyGUENOPtmGH2ZvZuBPisr7Mwih4mDNJJ/9YrnsdfdYWaf
WAysPGXYMfQy9jMiAC1cBm+jeIPvbIeZpYRzPt3vlFKAHpAZG1sp+r7SLfrT9e7x
7La/QPNVLMsKTjGMW82/qRzOXBed3htk9v2YPIHQubFIOOz2mXqwSPXCqUHuYKeU
eqzedvm0FGoeJbYTzpYyRAWU9OQtazOR+WAI8PrZiN4tdaxvYT2F5JJCMztYIoeq
SJdPUbWTsYxkc/Kj1FagW0LOydO40Aif53JbfrabnzcRYlWsxqQfaSsP8J8G4QDq
zXZvbt0IMan2B52X7AysDF8Zq4Ti8dVijvA7XNl7b5HFBrRpbOt9Tdhl/4zRiW14
Y16VswnIR+9qPhtSXiSkdOwB/0cAI6XEiBTgRunYccakGDUfLOEpIVqJJ1zGNHpl
hqJum3pAMW8i5JX8vl8J
=C4NU
-----END PGP SIGNATURE-----
Merge tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM DT updates from Olof Johansson:
"Device tree contents continue to be the largest branches we submit.
This time around, some of the contents worth pointing out is:
New SoC platforms:
- Freescale i.MX 7Solo
- Broadcom BCM23550
- Cirrus Logic EP7209 and EP7211 (clps711x platforms)_
- Hisilicon HI3519
- Renesas R8A7792
Some of the other delta that is sticking out, line-count wise:
- Exynos moves of IP blocks under an SoC bus, which causes a large
delta due to indentation changes
- a new Tegra K1 board: Apalis
- a bunch of small updates to many Allwinner platforms; new hardware
support, some cleanup, etc"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (426 commits)
ARM: dts: sun8i: Add dts file for inet86dz board
ARM: dts: sun8i: Add dts file for Polaroid MID2407PXE03 tablet
ARM: dts: sun8i: Use sun8i-reference-design-tablet for ga10h dts
ARM: dts: sun8i: Use sun8i-reference-design-tablet for polaroid mid2809pxe04
ARM: dts: sun8i: reference-design-tablet: Add drivevbus-supply
ARM: dts: Copy sun8i-q8-common.dtsi sun8i-reference-design-tablet.dtsi
ARM: dts: sun5i: Use sun5i-reference-design-tablet.dtsi for utoo p66 dts
ARM: dts: sun5i: Use sun5i-reference-design-tablet.dtsi for dit4350 dts
ARM: dts: sun5i: reference-design-tablet: Remove mention of q8
ARM: dts: sun5i: reference-design-tablet: Set lradc vref to avcc
ARM: dts: sun5i: Rename sun5i-q8-common.dtsi sun5i-reference-design-tablet.dtsi
ARM: dts: sun5i: Move q8 display bits to sun5i-a13-q8-tablet.dts
ARM: dts: sunxi: Rename sunxi-q8-common.dtsi sunxi-reference-design-tablet.dtsi
ARM: dts: at91: Don't build unnecessary dtbs
ARM: dts: at91: sama5d3x: separate motherboard gmac and emac definitions
ARM: dts: at91: at91sam9g25ek: fix isi endpoint node
ARM: dts: at91: move isi definition to at91sam9g25ek
ARM: dts: at91: fix i2c-gpio node name
ARM: dts: at91: vinco: fix regulator name
ARM: dts: at91: ariag25 : fix onewire node
...
This patch fixes the following DTC warnings for omap5-igep0050.dtb,
omap5-sbc-t54.dtb and omap5-uevm.dtb:
"connector@0 has a unit name, but no reg property"
"endpoint@0 has a unit name, but no reg property"
"encoder@0 has a unit name, but no reg property"
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The twl6040 codec is generating the pdmclk, which is used by the McPDM as
functional clock.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
with patches in Linux next:
- Fix omap5 and am57xx-idk input voltages to fix micro-sd
probing at least for some omap5-uevm configurations
- Fix unhandled fault for igepv5 audio
- Fix UART wakeirqs for omap5 by removing WAKUP_EN flags,
those are managed by the wakeirq and can currently confuse
the wakeirqs as there is no handler necessarily registered
- Fix LDO7 source for igepv5
Also included are few minor changes not strictly fixes
are good to have merged:
- Fix HP T410 boot time warnings for eMMC and disable the
unused MMC interfaces while at it
- Add dra7 gpmc dma channel
- Add igep00x0 SD card detect and write protect GPIOs
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=vMZg
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.7-dts-fixes1' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
DTS fixes for omaps for v4.7 merge window for issues noted
with patches in Linux next:
- Fix omap5 and am57xx-idk input voltages to fix micro-sd
probing at least for some omap5-uevm configurations
- Fix unhandled fault for igepv5 audio
- Fix UART wakeirqs for omap5 by removing WAKUP_EN flags,
those are managed by the wakeirq and can currently confuse
the wakeirqs as there is no handler necessarily registered
- Fix LDO7 source for igepv5
Also included are few minor changes not strictly fixes
are good to have merged:
- Fix HP T410 boot time warnings for eMMC and disable the
unused MMC interfaces while at it
- Add dra7 gpmc dma channel
- Add igep00x0 SD card detect and write protect GPIOs
* tag 'omap-for-v4.7-dts-fixes1' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: igep0020: Add SD card write-protect pin.
ARM: dts: igep00x0: Add SD card-detect.
ARM: dts: am57xx-idk-common: Fix input supply names
ARM: dts: dra7: Add gpmc dma channel
ARM: dts: disable mmc by default and enable when needed for dm814x
ARM: dts: Add non-removable to hsmmc on hp-t410
ARM: dts: Fix ldo7 source for HDMI on igepv5
ARM: dts: Fix uart wakeirq on omap5 by removing WAKEUP_EN for omaps
ARM: dts: Fix igepv5 audiopwon-gpio
ARM: dts: omap5-board-common: Describe the voltage supply mapping accurately
Signed-off-by: Olof Johansson <olof@lixom.net>
These are all the updates to device tree files for 32-bit platforms,
which as usual makes up the bulk of the ARM SoC changes: 462 non-merge
changesets, 450 files changed, 23340 insertions, 5216 deletions.
The three platforms that are added with the "soc" branch are here as well,
and we add some related machine files:
- For Aspeed AST2400/AST2500, we get the evaluation platform and
the Tyan Palmetto POWER8 mainboard that uses the AST2400 BMC
- For Oxnas 810SE, the Western Digital "My Book World Edition"
is added as the only platform at the moment.
- For ARM MPS2, the AN385 (Cortex-M3) and AN399 (Cortex-M7)
are supported
On the ARM Realview development platform, we now support all machines
with device tree, previously only the board files were supported, which
in turn will likely be removed soon.
Qualcomm IPQ4019 is the second generation ARM based "Internet Processor",
following the IPQ806x that is used in many high-end WiFi routers. This one
integrates two ath10k wifi radios that were previously on separate chips.
Other boards that got added for existing chips are:
- On Ti OMAP family:
- Amazon Kindle Fire, first generation, tablet and ebook reader
- OnRISC Baltos iR 2110 and 3220 embedded industrial PCs
- TI AM5728 IDK, TI AM3359 ICE-V2, and TI DRA722 Rev C EVM
development systems
- On Samsung EXYNOS platform:
- Samsung ARTIK5 evaluation board, see
https://www.artik.io/modules/overview/artik-5/
- On NXP i.MX platforms:
- Ka-Ro electronics TX6S-8034, TX6S-8035, TX6U-8033, TX6U-81xx,
TX6Q-1036, TX6Q-1110/-1130, TXUL-0010 and TXUL-0011 industrial
SoM modules
- Embest MarS Board i.MX6Dual DIY platform
- Boundary Devices i.MX6 Quad Plus Nitrogen6_MAX and
SoloX Nitrogen6sx embedded boards
- Technexion Pico i.MX6UL compute module
- ZII VF610 Development Board
- On Marvell embedded (mvebu, orion, kirkwood) platforms:
- Linksys Viper (E4200v2 / EA4500) WiFi router
- Buffalo Kurobox Pro NAS
- On Qualcomm Snapdragon:
- Arrow DragonBoard 600c (96boards) with APQ8064 Snapdragon 600
- On Rockchips platform:
- mqmaker MiQi single-board computer
- On Altera SoCFPGA:
- samtec VIN|ING 1000 vehicle communication interface
- On Allwinner Sunxi platforms:
- Dserve DSRV9703C tablet
- Difrnce DIT4350 tablet
- Colorfly E708 Q1 tablet
- Polaroid MID2809PXE04 tablet
- Olimex A20 OLinuXino LIME2 single board computer
- Xunlong Orange Pi 2, Orange Pi One, and Orange Pi PC
single board computers
Across many platforms, bug fixes went in to address warnings that
dtc now emits with 'make dtbs W=1'. Further changes for device enablement
went into Ti OMAP, bcm283x (Raspberry Pi), bcm47xx (wifi router),
Ti Davinci, Samsung EXYNOS, Marvell mvebu/kirkwood/orion, NXP i.MX/Vybrid
NXP LPC18xx, NXP LPC32xx, Renesas shmobile/r-mobile/r-car, Rockchips
rk3xxx, ST Ux500, ST STi, Atmel AT91/SAMA5, Altera SoCFPGA, Allwinner
Sunxi, Sigma Designs Tango, NVIDIA Tegra, Socionext Uniphier and ARM
Versatile Express.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIVAwUAVzuXhGCrR//JCVInAQJXjhAA1bV0fbREflRQrlXdMb4rNesygH8ikaja
gOYHE1yO+tSitHZ5g4w2yAFIEK7DzFdO5rz53BEINZfLCj4LO4495/z9ipqZQEjC
rw5IL89jAn8x4wF791SHjLpmmNRbHN2vjLcsX3ShJIHckip/jIbiU2aFJuohA0TU
jxpPAZzhaKsu/rDaVzHMS/im4LbZQ2qI3DxUUn6Kt8c468i4Ns22sowqSjh2xO/X
YiwHD0eAvDrySfMGiNT82wMMTfMF2KfXZGB885isMP4hK8OIDrOnI5nM9rxyRFfu
N14o0+tN1S2JzBHnqOOpib6JxYyCVr+QTjsKGAyR5X1mGINIhX8f1gy0EvFFxXKT
rIATc5VTeo4gc1quij8RVtDEp/4iJ8GspH4WGMh1F8tjTe+WUxeSMkxdf6/QY1+Q
vZKT0KKihoJQu1xI62NjnaRbfbhwx2BSWehwgXVd72lD19dG5LPw+Nj6/8+Bgouc
YxJahgkB9MMtHoNp8huMg33Gr9a07/yVxc4CztXtf7N9phd0nEXov2iM1aBgazLU
8IVd3Z9lZA+4iGVcj3oBJ6K1IkiCmg2qoNyF6tcInR5vPjKLECuxyuZw8VKuUuHD
k/s/rymSGRlDN5i4F0h0r4MvQ9gkYfwk8xiL3ofmwYHwo103Q7b7Cw55XRk88EoB
appd5QA+pko=
=Nx46
-----END PGP SIGNATURE-----
Merge tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM DT updates from Arnd Bergmann:
"These are all the updates to device tree files for 32-bit platforms,
which as usual makes up the bulk of the ARM SoC changes: 462 non-merge
changesets, 450 files changed, 23340 insertions, 5216 deletions.
The three platforms that are added with the "soc" branch are here as
well, and we add some related machine files:
- For Aspeed AST2400/AST2500, we get the evaluation platform and the
Tyan Palmetto POWER8 mainboard that uses the AST2400 BMC
- For Oxnas 810SE, the Western Digital "My Book World Edition" is
added as the only platform at the moment.
- For ARM MPS2, the AN385 (Cortex-M3) and AN399 (Cortex-M7) are
supported
On the ARM Realview development platform, we now support all machines
with device tree, previously only the board files were supported,
which in turn will likely be removed soon.
Qualcomm IPQ4019 is the second generation ARM based "Internet
Processor", following the IPQ806x that is used in many high-end WiFi
routers. This one integrates two ath10k wifi radios that were
previously on separate chips.
Other boards that got added for existing chips are:
Ti OMAP family:
- Amazon Kindle Fire, first generation, tablet and ebook reader
- OnRISC Baltos iR 2110 and 3220 embedded industrial PCs
- TI AM5728 IDK, TI AM3359 ICE-V2, and TI DRA722 Rev C EVM
development systems
Samsung EXYNOS platform:
- Samsung ARTIK5 evaluation board, see
https://www.artik.io/modules/overview/artik-5/
NXP i.MX platforms:
- Ka-Ro electronics TX6S-8034, TX6S-8035, TX6U-8033, TX6U-81xx,
TX6Q-1036, TX6Q-1110/-1130, TXUL-0010 and TXUL-0011 industrial
SoM modules
- Embest MarS Board i.MX6Dual DIY platform
- Boundary Devices i.MX6 Quad Plus Nitrogen6_MAX and SoloX
Nitrogen6sx embedded boards
- Technexion Pico i.MX6UL compute module
- ZII VF610 Development Board
Marvell embedded (mvebu, orion, kirkwood) platforms:
- Linksys Viper (E4200v2 / EA4500) WiFi router
- Buffalo Kurobox Pro NAS
Qualcomm Snapdragon:
- Arrow DragonBoard 600c (96boards) with APQ8064 Snapdragon 600
Rockchips platform:
- mqmaker MiQi single-board computer
Altera SoCFPGA:
- samtec VIN|ING 1000 vehicle communication interface
Allwinner Sunxi platforms:
- Dserve DSRV9703C tablet
- Difrnce DIT4350 tablet
- Colorfly E708 Q1 tablet
- Polaroid MID2809PXE04 tablet
- Olimex A20 OLinuXino LIME2 single board computer
- Xunlong Orange Pi 2, Orange Pi One, and Orange Pi PC single board
computers
Across many platforms, bug fixes went in to address warnings that dtc
now emits with 'make dtbs W=1'. Further changes for device enablement
went into Ti OMAP, bcm283x (Raspberry Pi), bcm47xx (wifi router), Ti
Davinci, Samsung EXYNOS, Marvell mvebu/kirkwood/orion, NXP i.MX/Vybrid
NXP LPC18xx, NXP LPC32xx, Renesas shmobile/r-mobile/r-car, Rockchips
rk3xxx, ST Ux500, ST STi, Atmel AT91/SAMA5, Altera SoCFPGA, Allwinner
Sunxi, Sigma Designs Tango, NVIDIA Tegra, Socionext Uniphier and ARM
Versatile Express"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (458 commits)
ARM: dts: tango4: Import watchdog node
ARM: dts: tango4: Update cpus node for cpufreq
ARM: dts: tango4: Update DT to match clk driver
ARM: dts: tango4: Initial thermal support
arm/dst: Add Aspeed ast2500 device tree
arm/dts: Add Aspeed ast2400 device tree
ARM: sun7i: dt: Add pll3 and pll7 clocks
ARM: dts: sunxi: Add a olinuxino-lime2-emmc
ARM: dts: at91: sama5d4: add trng node
ARM: dts: at91: sama5d3: add trng node
ARM: dts: at91: sama5d2: add trng node
ARM: dts: at91: at91sam9g45 family: reduce the trng register map size
ARM: sun4i: dt: Add pll3 and pll7 clocks
ARM: sun5i: chip: Enable the TV Encoder
ARM: sun5i: r8: Add display blocks to the DTSI
ARM: sun5i: a13: Add display and TCON clocks
ARM: dts: ux500: configure the accelerometers open drain
ARM: mx5: dts: Enable USB OTG on M53EVK
ARM: dts: imx6ul-14x14-evk: Add audio support
ARM: dts: imx6qdl: Remove unneeded unit-addresses
...
The padconf register WAKEUP_EN is now handled in a generic way using
Linux wakeirqs where pinctrl-single toggles the WAKEUP_EN bit when
a wakeirq is enabled or disabled.
At least omap5 gets confused if the WAKEUP_EN bit is set and the pin
is not claimed as a wakeirq. The end result is that wakeirqs don't
work properly as there is nothing handling the wakeirq.
So let's just remove the WAKEUP_EN usage from dts files.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Playing audio works on omap5-uevm, but produces an "Unhandled fault:
imprecise external abort (0x1406) at 0x00000000" error on igepv5.
Looks like the twl6040 audpwron GPIO pin is different for these
boards. Let's fix the issue by configuring the audpwron in the
board specific dts file.
Cc: Agustí Fontquerni <af@iseebcn.com>
Cc: Eduard Gavin <egavin@iseebcn.com>
Cc: Enric Balletbo i Serra <eballetbo@gmail.com>
Acked-by: Peter Ujfalusi <peter.ujflausi@ti com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
OMAP5uEVM based platforms share a similar voltage rail map. This
should be properly described in device tree, without this regulator core
will be unable to determine the source voltage of LDOs such as LDO9 and
SMPS10 which could be configured for bypass depending on the voltage
requested of them. This results in conditions such as:
ldo9: bypassed regulator has no supply!
ldo9: failed to get the current voltage(-517)
palmas-pmic 48070000.i2c:palmas@48:palmas_pmic: failed to register
48070000.i2c:palmas@48:palmas_pmic regulator
Cc: Agustí Fontquerni <af@iseebcn.com>
Cc: Eduard Gavin <egavin@iseebcn.com>
Cc: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
[tony@atomide.com: fixed to use palmas style in-supply]
Signed-off-by: Tony Lindgren <tony@atomide.com>
ldo4_reg is connected to DSS, and should always be 1.8V. However the
The dts defines a range of 1.5V-1.8V, which requires somethings to set
the actual voltage at runtime. Currently we set the voltage in omapdss
driver.
As the voltage must always be 1.8V, let's just define the range to 1.8V
so that the driver doesn't need to deal with the voltage. In fact, the
driver should not touch the voltage, except in the cases where the
voltage needs to be changed at runtime.
I presume the situation is the same for ldo1_reg, used for CSI, although
I think it is not currently used in the mainline.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The palmas PMIC has two control lines that need to be muxed properly
for things to work. The sys_nirq pin is used for interrupts, and msecure
pin is used for enabling writes to some PMIC registers.
Without these pins configured properly things can fail in mysterious
ways. For example, we can't update the RTC registers on palmas PMIC
unless the msecure pin is configured. And this is probably the reason
why we had RTC missing from the omap5 dts file.
According to "OMAP5430 ES2.0 Data Manual [Public] VErsion A (Rev. F)"
swps052f.pdf, mux mode 1 is for sys_drm_msecure so in theory there's
should be no need to configure it as a GPIO pin.
However, it seems there are some reliability issues using the msecure
mux mode. And the TI trees configure the msecure pin as GPIO out high
instead.
As the PMIC only cares that the msecure line is high to allow access
to the RTC registers, let's use a GPIO hog as suggested by Nishanth
Menon <nm@ti.com>. Also the use of the internal pull was considered
but supposedly that may not be capable of keeping the line high in
a noisy environment.
If we ever see high security omap5 products in the mainline tree,
those need to skip the msecure pin muxing and ignore setting the GPIO
hog. Chances are the related pin mux registers are locked in that case
and the msecure pin is managed by whatever software may be running in
the ARM TrustZone.
Who knows what the original intention of the msecure pin was. Maybe
it was supposed to prevent the system time to be set back for some
game demo modes to time out? Anyways, it seems that later PMICs like
tps659037 have recycled this pin for "powerhold" and devices like
beagle-x15 do not need changes to the msecure pin configuration.
To avoid further confusion with TWL variant PMICs, beagle-x15 does
not have a back-up battery for RTC palmas. Instead the mcp79410 RTC
is used with rtc-ds1307 driver. There is a "powerhold" jumper j5
holes near the palmas PMIC, and shorting it seems to power up
beagle-x15 automatically. It is unknown if it also has other side
effects to the beagle-x15 power up sequence.
Cc: stable@vger.kernel.org # v4.4
Signed-off-by: Tony Lindgren <tony@atomide.com>
Use the pinmux IOPAD macros to define the register as an offset from
the padconf physical address instead of the offset from padconf base.
This makes the DTS easier to read since matches the addresses listed
in the Technical Reference Manual.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Looks like thevarious omap5-uevm models and igepv5 are very similar. So let's
create omap5-board-common.dtsi to allow fixing up things properly for mainline
kernel to support all these.
Even if we eventually end up having only PMIC + MMC + eMMC + SDIO WLAN + SATA +
USB + HDMI configuration in the omap5-board-common.dtsi, this is the easiest
way to add support for other boards rather than diffing various versions of
out of tree dts files.
My guess is that also omap5-sbc-t54.dts can use this, but I don't have that
board so that will need to be dealt with later on.
Signed-off-by: Tony Lindgren <tony@atomide.com>
