Pull "Samsung DTS ARM changes for 4.15" from Krzysztof Kozłowski:
1. Add new board: Hardkernel Odroid HC1.
2. Fix incomplete Odroid-XU3/4 thermal-zones definition leading to
possible overheat if first pair of A7+A15 cores is idle but rest of
CPUs are busy.
3. Add capacity-dmips-mhz properties for CPUs of octa-core SoCs.
4. Add power button to Odroid XU3/4.
5. Improvements in Gscaler, HDMI and Mixer blocks on Exynos5.
6. Add suspend quirk to DWC3 USB controller to fix enumeration of
SuperSpeed devices on Odroid XU4.
7. Add HDMI and MHL to Trats2.
8. Cleanups (redundant properties and nodes).
* tag 'samsung-dt-4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
dt-bindings: samsung: Document binding for new Odroid HC1 board
ARM: dts: exynos: Add HDMI and Sil9234 to Trats2 board
ARM: dts: exynos: Add support for Hardkernel's Odroid HC1 board
ARM: dts: exynos: Move audio clocks configuration to odroidxu3-audio.dtsi
ARM: dts: exynos: Add dwc3 SUSPHY quirk
ARM: dts: exynos: Add status property to Exynos 542x Mixer nodes
ARM: dts: exynos: Add status property to Exynos 5250 HDMI and Mixer nodes
ARM: dts: exynos: Cleanup HDMI DCC definitions on Exynos5250 and Exynos542x boards
ARM: dts: exynos: Move HDMI PHY node from boards to exynos5250.dtsi
ARM: dts: exynos: Use specific compatibles for proper Gscaler limits on Exynos5250 and Exynos5420
ARM: dts: exynos: Remove redundant interrupt properties in gpio-keys on Odroid boards
ARM: dts: exynos: Add power button for Odroid XU3/4
ARM: dts: exynos: Remove the display-timing and delay from Rinato
ARM: dts: exynos: add exynos5422 cpu capacity-dmips-mhz information
ARM: dts: exynos: add exynos5420 cpu capacity-dmips-mhz information
ARM: dts: exynos: fix incomplete Odroid-XU3/4 thermal-zones definition
Fix dtc warnings for 'simple_bus_reg' due to leading 0s. Converted using
the following command:
perl -p -i -e 's/\@0+([0-9a-f])/\@$1/g' `find arch/arm/boot/dts -type -f -name '*.dts*'
Dropped changes to ARM, Ltd. boards LED nodes and manually fixed up some
occurrences of uppercase hex.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
GPIO keys don't need interrupt property. Interrupt number can be derived
directly from the GPIO pin definition, so remove redundant 'interrupts'
and 'interrupt-parent' properties from gpio-keys nodes on
Exynos4412-based Odroid boards.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
dwmmc driver deprecated num-slots and plan to get rid
of it finally. Just move a step to cleanup it from DT.
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Replace hard-coded values of interrupt flags with respective macros from
header to increase code readability.
Suggested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Watchdog module does not have external dependencies so it can be safely
enabled in exynos4.dtsi thus making it available for all Exynos4-based
boards.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Add CPU operating points for Exynos4412 Prime (it supports
additional 1704MHz & 1600MHz OPPs and 1500MHz OPP is just
a regular non-turbo OPP on this SoC). Also update relevant
cooling maps to account for new OPPs.
ODROID-X2/U2/U3 boards use Exynos4412 Prime SoC version so
update their board files accordingly.
Based on Hardkernel's kernel for ODROID-X2/U2/U3 boards.
Cc: Doug Anderson <dianders@chromium.org>
Cc: Andreas Faerber <afaerber@suse.de>
Cc: Thomas Abraham <thomas.ab@samsung.com>
Cc: Tobias Jakobi <tjakobi@math.uni-bielefeld.de>
Cc: Ben Gamari <ben@smart-cactus.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Move assigned clocks properties from sound node to audio subsystem clock
controller node. This way clocks topology and rates are set just after
probing audio clocks controller. Leaving those properties under
sound node doesn't guarantee to configure them before they are being used
(for example i2s hardware module can be probed in parallel and it also
require proper audio clocks configuration).
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
"iis", "i2s_opclk0" and "i2s_opclk1" are standard clocks for Exynos4 I2S
hardware module, so they should be defined in .dtsi file not in the random
board .dts file.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Replace in DT sources hard-coded values for pinctrl configuration like pull
up/down, drive strength and function. This makes the DTS easier to read,
especially that some drive strengths values are quite non-obvious.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=NN8A
-----END PGP SIGNATURE-----
Merge tag 'samsung-dt-pinctrl-4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into next/dt
Pull "Topic branch for Samsung DeviceTree cleanup for 4.9" from Krzysztof Kozłowski:
Replace in DT sources hard-coded values for pinctrl configuration like pull
up/down, drive strength and function. This makes the DTS easier to read,
especially that some drive strengths values are quite non-obvious.
* tag 'samsung-dt-pinctrl-4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
ARM: dts: s3c64xx: Use macros for pinctrl configuration
ARM: dts: s3c2416: Use macros for pinctrl configuration
ARM: dts: s5pv210: Use macros for pinctrl configuration
ARM: dts: s3c64xx: Use common macros for pinctrl configuration
ARM: dts: exynos: Fix mismatched values of SD drive strengh configuration on exynos4415
ARM: dts: exynos: Fix mismatched value for SD4 pull up/down configuration on exynos4210
ARM: dts: exynos: Use macros for pinctrl configuration on exynos542x/exynos5800
ARM: dts: exynos: Use macros for pinctrl configuration on exynos5410
ARM: dts: exynos: Use macros for pinctrl configuration on exynos5260
ARM: dts: exynos: Use macros for pinctrl configuration on exynos5250
ARM: dts: exynos: Use macros for pinctrl configuration on exynos4415
ARM: dts: exynos: Use macros for pinctrl configuration on exynos4x12
ARM: dts: exynos: Use macros for pinctrl configuration on exynos4210
ARM: dts: exynos: Use macros for pinctrl configuration on exynos3250
ARM: dts: exynos: Use common macros for pinctrl configuration
pinctrl: dt-bindings: samsung: Update documentation with new macros
pinctrl: dt-bindings: samsung: Add header with values used for configuration
Usage of DTS macros instead of hard-coded numbers makes code easier to
read. One does not have to remember which value means pull-up/down or
specific driver strength.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
This patch enables getting a HPD GPIO descriptor quicker.
The exynos-hdmi driver uses "hpd" for HDMI hot plug detection.
static int hdmi_resources_init(struct hdmi_context *hdata)
{
...
hdata->hpd_gpio = devm_gpiod_get(dev, "hpd", GPIOD_IN);
...
}
This calls 'of_find_gpio()' and it generates the GPIO consumer ID by referring
GPIO suffix. So 'hpd-gpios' is preferred on getting a GPIO descriptor.
However, if the device tree uses 'hpd-gpio', then the exynos-hdmi driver
always retries to get a GPIO descriptor because the first GPIO suffix is not
'gpio' but 'gpios'. So you always see the debug message below.
of_get_named_gpiod_flags: can't parse 'hpd-gpios' property of node '/soc/hdmi@14530000[0]'
Use the preferred property, 'hpd-gpios' instead of 'hpd-gpio'.
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Cc: devicetree@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-samsung-soc@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Milo Kim <woogyom.kim@gmail.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Replace hardcoded reserved memory ranges with auto-allocated ones
and enable MFC for all boards.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=sS8p
-----END PGP SIGNATURE-----
Merge tag 'samsung-drivers-exynos-mfc-4.8-2' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into next/dt
Topic branch for Exynos MFC changes for v4.8, part 2:
Replace hardcoded reserved memory ranges with auto-allocated ones
and enable MFC for all boards.
* tag 'samsung-drivers-exynos-mfc-4.8-2' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
ARM: dts: exynos: enable MFC device for all boards
ARM: dts: exynos: move MFC reserved memory regions from boards to .dtsi
ARM: dts: exynos: replace hardcoded reserved memory ranges with auto-allocated ones
ARM: dts: exynos: Enable MFC device on Exynos4412 Odroid boards
ARM: dts: exynos: Convert MFC device to generic reserved memory bindings
ARM: EXYNOS: Remove code for MFC custom reserved memory handling
media: s5p-mfc: add iommu support
media: s5p-mfc: replace custom reserved memory handling code with generic one
media: s5p-mfc: use generic reserved memory bindings
of: reserved_mem: add support for using more than one region for given device
media: set proper max seg size for devices on Exynos SoCs
media: vb2-dma-contig: add helper for setting dma max seg size
s5p-mfc: Fix race between s5p_mfc_probe() and s5p_mfc_open()
s5p-mfc: Add release callback for memory region devs
s5p-mfc: Set device name for reserved memory region devs
Signed-off-by: Olof Johansson <olof@lixom.net>
MFC device can be used without any external hardware dependencies (when
IOMMU is enabled), so it can be enabled by default (like it has been
already done for Exynos 542x platforms). This unifies handling of this
device for Exynos3250, Exynos4 and Exynos542x platforms. Board can still
include exynos-mfc-reserved-memory.dtsi to enable using this device
without IOMMU being enabled.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
This patch moves assigning reserved memory regions from each board dts
to common exynos-mfc-reserved-memory.dtsi file, where those regions are
defined.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Enable support for Multimedia Codec (MFC) device for all Exynos4412-based
Odroid boards.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Odroid X/X2/U3 schematics say that SD card vmmc regulator
(LDO21/TFLASH) operates on 2.8 V. Mainline U-Boot uses that value as
well and 2.8 V is common on Exynos-based boards. Additionally use some
descriptive name for this regulator.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
The eMMC card vmmc-supply contained incorrectly two regulators: LDO20
and buck8. The second one is ignored. Additionally the buck8 is a vqmmc
supply only on X and X2. On U3 the buck8 is providing power to the LAN
(SMSC95xx) so instead the LDO22 should be used.
Fix this by defining proper vmmc and vqmmc supplies for respective
boards.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
The SD-card vmmc-supply contained incorrectly two regulators. The second
one is ignored. Fix this by defining proper vmmc and vqmmc supplies.
Additionally these regulators do not have to be always on, so allow
disabling them to reduce energy consumption.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
This is a collection of a few late fixes and other misc. stuff that
had dependencies on things being merged from other trees.
The Renesas R-Car power domain handling, and the Nvidia Tegra USB
support both hand notable changes that required changing the DT binding
in a way that only provides compatibility with old DT blobs on new
kernels but not vice versa. As a consequence, the DT changes
are based on top of the driver changes and are now in this branch.
For NXP i.MX and Samsung Exynos, the changes in here depend on
other changes that got merged through the clk maintainer tree.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=I0Be
-----END PGP SIGNATURE-----
Merge tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC late DT updates from Arnd Bergmann:
"This is a collection of a few late fixes and other misc stuff that had
dependencies on things being merged from other trees.
The Renesas R-Car power domain handling, and the Nvidia Tegra USB
support both hand notable changes that required changing the DT
binding in a way that only provides compatibility with old DT blobs on
new kernels but not vice versa. As a consequence, the DT changes are
based on top of the driver changes and are now in this branch.
For NXP i.MX and Samsung Exynos, the changes in here depend on other
changes that got merged through the clk maintainer tree"
* tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (35 commits)
ARM: dts: exynos: Add support of Bus frequency using VDD_INT for exynos5422-odroidxu3
ARM: dts: exynos: Add bus nodes using VDD_INT for Exynos542x SoC
ARM: dts: exynos: Add NoC Probe dt node for Exynos542x SoC
ARM: dts: exynos: Add support of bus frequency for exynos4412-trats/odroidu3
ARM: dts: exynos: Expand the voltage range of buck1/3 regulator for exynos4412-odroidu3
ARM: dts: exynos: Add support of bus frequency using VDD_INT for exynos3250-rinato
ARM: dts: exynos: Add exynos4412-ppmu-common dtsi to delete duplicate PPMU nodes
ARM: dts: exynos: Add bus nodes using VDD_MIF for Exynos4210
ARM: dts: exynos: Add bus nodes using VDD_INT for Exynos4x12
ARM: dts: exynos: Add bus nodes using VDD_MIF for Exynos4x12
ARM: dts: exynos: Add bus nodes using VDD_INT for Exynos3250
ARM: dts: exynos: Add DMC bus frequency for exynos3250-rinato/monk
ARM: dts: exynos: Add DMC bus node for Exynos3250
ARM: tegra: Enable XUSB on Nyan
ARM: tegra: Enable XUSB on Jetson TK1
ARM: tegra: Enable XUSB on Venice2
ARM: tegra: Add Tegra124 XUSB controller
ARM: tegra: Move Tegra124 to the new XUSB pad controller binding
ARM: dts: r8a7794: Use SYSC "always-on" PM Domain
ARM: dts: r8a7793: Use SYSC "always-on" PM Domain
...
This patch adds the bus device tree nodes for both MIF (Memory) and INT
(Internal) block to enable the bus frequency.
The DMC bus is parent device in MIF block using VDD_MIF and the LEFTBUS
bus is parent device in INT block using VDD_INT.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
[m.reichl and linux.amoon: Tested it on exynos4412-odroidu3 board]
Tested-by: Markus Reichl <m.reichl@fivetechno.de>
Tested-by: Anand Moon <linux.amoon@gmail.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
This patch expands the voltage range of buck1/3 regulator due to as following:
- MIF (Memory Interface) bus frequency needs the range of '900 - 1100 mV'.
- INT (Internal) bus frequency needs the range of '900 - 1050 mV'.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
[m.reichl and linux.amoon: Tested it on exynos4412-odroidu3 board]
Tested-by: Markus Reichl <m.reichl@fivetechno.de>
Tested-by: Anand Moon <linux.amoon@gmail.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
This patch adds the exynos4412-ppmu-common.dtsi to remove duplicate PPMU nodes
because exynos3250-rinato/monk, exynos4412-trats2/odroidu3 has the same
PPMU device tree node.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
[m.reichl and linux.amoon: Tested it on exynos4412-odroidu3 board]
Tested-by: Markus Reichl <m.reichl@fivetechno.de>
Tested-by: Anand Moon <linux.amoon@gmail.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
There is no external dependency for Security SubSystem (SSS) block so
the nodes for Pseudo Random Number Generator and AES hardware
acceleration can be enabled always for all Exynos4 devices.
Suggested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Add a dts node entry and enable the HDMI CEC device present in the Exynos4
family of SoCs.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
[k.kozlowski: Put the node in alphabetical order]
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Enable the Security SubSystem (SSS) on Exynos4412-based Odroid boards
to provide hardware acceleration for AES operations.
Suggested-by: Tobias Jakobi <tjakobi@math.uni-bielefeld.de>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Tested-by: Tobias Jakobi <tjakobi@math.uni-bielefeld.de>
Though the keyboard and other driver will continue to support the legacy
"gpio-key,wakeup", "linux-keypad,wakeup" boolean property to enable the
wakeup source, "wakeup-source" is the new standard binding.
This patch replaces all the legacy wakeup properties with the unified
"wakeup-source" property in order to avoid any further copy-paste
duplication.
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
G2D device is always available and doesn't depend on any external (board
specific) peripherals, so it can be unconditionally enabled.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
The board DTS are using numeric values instead of the defined GPIO
constanst to express polarity, use them to make the DTS more clear.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Use 'ldoN_reg: LDON' syntax and drop the deprecated
'regulator-compatible' property.
Signed-off-by: Tobias Jakobi <tjakobi@math.uni-bielefeld.de>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
The pinctrl settings in i2c_0 and i2c_1 are already provided
through the exynos4 dtsi.
Signed-off-by: Tobias Jakobi <tjakobi@math.uni-bielefeld.de>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
For Exynos4x12 platforms, add CPU operating points (using
opp-v2 bindings) and CPU regulator supply properties for
migrating from Exynos specific cpufreq driver to using
generic cpufreq driver.
Based on the earlier work by Thomas Abraham.
Cc: Doug Anderson <dianders@chromium.org>
Cc: Andreas Faerber <afaerber@suse.de>
Cc: Thomas Abraham <thomas.ab@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Tested-by: Tobias Jakobi <tjakobi@math.uni-bielefeld.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Tested-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Usage of labels instead of full paths reduces possible mistakes when
overriding nodes.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
For thermal zones:
Acked-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
The Exynos4412 SoC has a s3c6410 RTC where the source clock
is now a mandatory property.
This patch fixes probe failure of s3c-rtc on Odroid-X2/U2/U3 boards.
Signed-off-by: Markus Reichl <m.reichl@fivetechno.de>
Tested-by: Tobias Jakobi <tjakobi@math.uni-bielefeld.de>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Tested-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
- for exynos3250
: add assigned clock parents for CMU nodes
- for exynos4412-odroid
: add eMMC reset line
- for exynos5250
: fixed typo for interrupt-cells
- for exynos5250-snow
: define stdout-path property
: represent bridge and panel connection
: enable wifi power-on and add cap-sdio-irq to wifi mmc node
- for exynos5250-spring
: define stdout-path property
- for exynos5420
: fixed typo for interrupt-cells
: add async-bridge clocks for gsc and disp1 PDs
- for exynos5420 boards
: Mux XMMCnDATA[0] pad correctly
- for exynos5420-odroidxu3
: add eMMC reset line
- for Peach boards
: add HS400 support and define stdout-path property
: add mclk entry and add WiFi module support
: represent bridge and panel connection
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=Sz8u
-----END PGP SIGNATURE-----
Merge tag 'samsung-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into next/dt
Merge "Samsung DT updates for v4.1" from Kukjin Kim:
- for exynos3250
: add assigned clock parents for CMU nodes
- for exynos4412-odroid
: add eMMC reset line
- for exynos5250
: fixed typo for interrupt-cells
- for exynos5250-snow
: define stdout-path property
: represent bridge and panel connection
: enable wifi power-on and add cap-sdio-irq to wifi mmc node
- for exynos5250-spring
: define stdout-path property
- for exynos5420
: fixed typo for interrupt-cells
: add async-bridge clocks for gsc and disp1 PDs
- for exynos5420 boards
: Mux XMMCnDATA[0] pad correctly
- for exynos5420-odroidxu3
: add eMMC reset line
- for Peach boards
: add HS400 support and define stdout-path property
: add mclk entry and add WiFi module support
: represent bridge and panel connection
* tag 'samsung-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: dts: Fixed typo interrupt-cells for exynos5420 and exynos5250
ARM: dts: Add HS400 support for exynos5420 and exynos5800
ARM: dts: add async-bridge clocks to gsc power domain for exynos5420
ARM: dts: add async-bridge clocks to disp1 power domain for exynos5420
dt-bindings: add asynchronous bridge clock for exynos
ARM: dts: Define stdout-path property for exynos5250-spring
ARM: dts: Define stdout-path property for exynos5250-snow
ARM: dts: Define stdout-path property for Peach boards
ARM: dts: Add assigned clock parents to CMU node for exynos3250
ARM: dts: Add mclk entry for Peach boards
ARM: dts: Add WiFi module support for Peach boards
ARM: dts: Mux XMMCnDATA[0] pad correctly for Exynos5420 boards
ARM: dts: add eMMC reset line for exynos5422-odroidxu3
ARM: dts: add eMMC reset line for exynos4412-odroid-common
ARM: dts: represent bridge and panel connection for exynos5420-peach-pit
ARM: dts: represent bridge and panel connection for exynos5250-snow
ARM: dts: Add cap-sdio-irq to wifi mmc node for exynos5250-snow
ARM: dts: Enable wifi power-on for exynos5250-snow
Signed-off-by: Olof Johansson <olof@lixom.net>
This patch adds nodes specific to Exynos4412 based Odroid X/X2/U2/U3
boards required for enabling HDMI display.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Presented patch aims to move data necessary for correct CPU cooling device
configuration from exynos_tmu_data.c to device tree.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Acked-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
This commit enables TMU IP block on the Exynos4412 Odroid based
devices such as Odroid U3.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Acked-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
This patch adds reset-gpios property to the eMMC slot, so the MMC driver
is able to properly reset eMMC card on system restart and thus fixes
system hang on software reboot.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
DT changes continue to be the bulk of our merge window contents.
We continue to have a large set of changes across the board as new platforms
and drivers are added.
Some of the new platforms are:
- Alphascale ASM9260
- Marvell Armada 388
- CSR Atlas7
- TI Davinci DM816x
- Hisilicon HiP01
- ST STiH418
There have also been some sweeping changes, including relicensing of DTS
contents from GPL to GPLv2+/X11 so that the same files can be reused in
other non-GPL projects more easily. There's also been changes to the
DT Makefile to make it a little less conflict-ridden and churny down
the road.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=XEw1
-----END PGP SIGNATURE-----
Merge tag 'dt-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC DT updates from Olof Johansson:
"DT changes continue to be the bulk of our merge window contents.
We continue to have a large set of changes across the board as new
platforms and drivers are added.
Some of the new platforms are:
- Alphascale ASM9260
- Marvell Armada 388
- CSR Atlas7
- TI Davinci DM816x
- Hisilicon HiP01
- ST STiH418
There have also been some sweeping changes, including relicensing of
DTS contents from GPL to GPLv2+/X11 so that the same files can be
reused in other non-GPL projects more easily. There's also been
changes to the DT Makefile to make it a little less conflict-ridden
and churny down the road"
* tag 'dt-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (330 commits)
ARM: dts: Add PPMU node for exynos4412-trats2
ARM: dts: Add PPMU node for exynos3250-monk and exynos3250-rinato
ARM: dts: Add PPMU dt node for exynos4 and exynos4210
ARM: dts: Add PPMU dt node for exynos3250
ARM: dts: add mipi dsi device node for exynos4415
ARM: dts: add fimd device node for exynos4415
ARM: dts: Add syscon phandle to the video-phy node for Exynos4
ARM: dts: Add sound nodes for exynos4412-trats2
ARM: dts: Fix CLK_MOUT_CAMn parent clocks assignment for exynos4412-trats2
ARM: dts: Fix CLK_UART_ISP_SCLK clock assignment in exynos4x12.dtsi
ARM: dts: Add max77693 charger node for exynos4412-trats2
ARM: dts: Switch max77686 regulators to GPIO control for exynos4412-trats2
ARM: dts: Add suspend configuration for max77686 regulators for exynos4412-trats2
ARM: dts: Add Maxim 77693 fuel gauge node for exynos4412-trats2
ARM: dts: am57xx-beagle-x15: Fix USB2 mode
ARM: dts: am57xx-beagle-x15: Add extcon nodes for USB
ARM: dts: dra72-evm: Add extcon nodes for USB
ARM: dts: dra7-evm: Add extcon nodes for USB
ARM: dts: rockchip: move the hdmi ddc-i2c-bus property to the actual boards
ARM: dts: rockchip: enable vops and hdmi output on rk3288-firefly and -evb
...
Here's the big tty/serial driver update for 3.20-rc1. Nothing huge
here, just lots of driver updates and some core tty layer fixes as well.
All have been in linux-next with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlTgtgkACgkQMUfUDdst+ykXbACg14oFAmeYjO9RsdIHPXBvKseO
47QAn0foy91bpNQ5UFOxWS5L6Fzj2ZND
=syx2
-----END PGP SIGNATURE-----
Merge tag 'tty-3.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial driver patches from Greg KH:
"Here's the big tty/serial driver update for 3.20-rc1. Nothing huge
here, just lots of driver updates and some core tty layer fixes as
well. All have been in linux-next with no reported issues"
* tag 'tty-3.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (119 commits)
serial: 8250: Fix UART_BUG_TXEN workaround
serial: driver for ETRAX FS UART
tty: remove unused variable sprop
serial: of-serial: fetch line number from DT
serial: samsung: earlycon support depends on CONFIG_SERIAL_SAMSUNG_CONSOLE
tty/serial: serial8250_set_divisor() can be static
tty/serial: Add Spreadtrum sc9836-uart driver support
Documentation: DT: Add bindings for Spreadtrum SoC Platform
serial: samsung: remove redundant interrupt enabling
tty: Remove external interface for tty_set_termios()
serial: omap: Fix RTS handling
serial: 8250_omap: Use UPSTAT_AUTORTS for RTS handling
serial: core: Rework hw-assisted flow control support
tty/serial: 8250_early: Add support for PXA UARTs
tty/serial: of_serial: add support for PXA/MMP uarts
tty/serial: of_serial: add DT alias ID handling
serial: 8250: Prevent concurrent updates to shadow registers
serial: 8250: Use canary to restart console after suspend
serial: 8250: Refactor XR17V35X divisor calculation
serial: 8250: Refactor divisor programming
...
Now when the CDCLK I2S output clock can be handled through the clock
API the Odroid X2/U3 can be switched to the simple-audio-card DT binding.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Clock related properties are added to the Exynos4 I2S device nodes
so they can be referred to as clock providers. Missing i2s_opclk1
clock is added to the I2S0 node and clock properties are added
to the MAX98090 codec node to allow it to control/read frequency
of the MCLK clock directly.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds stdout-path property to chosen nodes of Exynos4 boards
to enable use of earlycon feature without the need to hardcode port
number in kernel itself.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
All currently supported boards use hsotg/dwc2 controller in device
('peripheral') mode, so add property which sets correct operation mode.
This patch fixes support in recent changes in dwc2 driver, which added
support for dual-role devices.
Suggested-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
This ensures the core and the audio subsystem clocks are configured
properly, as expected by the sound machine driver. These bits are
missing to obtain proper audio sample rates in kernel v3.17, where
audio support for Odroid X2/U3 was first added.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Specify the default mux and divider clocks in device tree
to ensure the FIMC devices on Trats, Trats2, Universal_c210
and Odroid X2/U3 boards are clocked from recommended clock
source and with maximum supported frequency.
For Trats2 also the MIPI-CSIS and the camera sensor clocks
are configured, the 'clock-frequency' property is deprecated
in favour of 'assigned-clock-rates' property.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
dw-mmc controller can support multiple slots.
But, there are no use-cases anywhere. So we don't need to support the
slot-node for dw-mmc controller.
And "supports-highspeed" property in dw-mmc is deprecated.
"supports-highspeed" property can be replaced with "cap-sd/mmc-highspeed".
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Tushar Behera <trblinux@gmail.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Sachin Kamat <sachin.kamat@samsung.com>
[kgene.kim@samsung.com: rebased exynos5250-snow changes]
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Increase max i2c bus frequency beyond the default for faster
data transfers. According to the manual, these faster speeds are
only available when the board is wired up the right way. In this case,
the vendor kernel has run at this speed for a long time.
sda-delay is needed for talking to RTC on PMIC, otherwise the i2c
controller never sees an ACK. Strangely the other PMIC i2c slave (the
main one) works fine even without this delay. I Chose value 100 to
match the vendor kernel.
Signed-off-by: Daniel Drake <drake@endlessm.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Tested-by: Tomeu Vizoso <tomeu@tomeuvizoso.net>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
