We only want this initcall to run when the kernel is
booted on omap SoCs. Fix the issue by initializing the
the initcall from separately for omap1 and omap2+.
This fixes the issue for omap2+ multiplatform configs
as we are using omap_subsys_initcall there.
Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
As discussed on linux-arm-kernel, we want to avoid
relative includes for the arch/arm/*omap* shared code:
http://www.spinics.net/lists/linux-omap/msg80520.html
To fix this for the shared i2c.h, let's re-introduce
a minimal plat/i2c.h.
Note that drivers must not use this header as it will
break build for omap2+ CONFIG_MULTIPLATFORM builds.
Signed-off-by: Tony Lindgren <tony@atomide.com>
There's no need to keep the device related things in the
common i2c.c as omap2+ is using hwmod. Split the code to
mach-omap1 and mach-omap2 parts and only leave common
code to plat-omap/i2c.c.
Note that as omap1 only has one i2c controller, we can
now remove the old device related macros.
Reviewed-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The sequence of _ocp_softreset doesn't work for i2c. The i2c module has a
special sequence to reset the module. The sequence is
- Disable the I2C.
- Write to SOFTRESET bit.
- Enable the I2C.
- Poll on the RESETDONE bit.
The sequence is implemented as a function and the i2c_class is updated with
the correct 'reset' pointer. omap_hwmod_softreset function is implemented
which triggers the softreset by writing into sysconfig register. On following
this sequence, i2c module resets properly and timeouts are not seen.
Cc: Rajendra Nayak <rnayak@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Cc: Kevin Hilman <khilman@ti.com>
Signed-off-by: Avinash.H.M <avinashhm@ti.com>
[paul@pwsan.com: combined this patch with a patch to remove
HWMOD_INIT_NO_RESET from the 44xx hwmod flags; change register
offset conditional code to use the IP block revision; minor code
cleanup]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
These represent the two kinds of (incompatible) OMAP I2C
peripheral unit in use so far.
The constants are in linux/i2c-omap.h so the omap i2c driver can have
them too.
Cc: patches@linaro.org
Cc: Ben Dooks <ben-linux@fluff.org>
Reported-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Andy Green <andy.green@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
As part of removing cpu_...() from the OMAP I2C driver, we need to
convert the CPU tests into functionality flags that are set by
hwmod class in the same way the IP revision is.
More flags are needed than will fit in the existing u8 flags
member of omap_i2c_dev_attr.
These flags can refer to options inside the IP block but they are
most needed for information about cpu implementation specific
options that are not part of the IP block itself. For example,
how the CPU data bus is wired to the IP block databus differs
between OMAP cpus and affects how you must shift the address in
the IP block, but is not a feature of the IP block itself.
Cc: patches@linaro.org
Cc: Ben Dooks <ben-linux@fluff.org>
Reported-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Andy Green <andy.green@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Add hwmod structures for I2C controllers on OMAP3430.
This patch was developed in collaboration with Paul Walmsley
<paul@pwsan.com>.
OMAP3 fixes for correct IDLEST bit monitoring from
G, Manjunath Kondaiah <manjugk@ti.com>
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: G, Manjunath Kondaiah <manjugk@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
The commit b63128e812 broke the pin muxing
for I2C busses that are enabled from the kernel command line.
Fix this by defining the board registration function omap_register_i2c_bus
in common platform code as it was before but keep the muxing in architecture
dependent files.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Otherwise we cannot limit new mux code to mach-omap2.
The same signal names should eventually work for other
omaps under mach-omap2.
Note that these pins don't need to be OMAP_PIN_INPUT_PULLUP,
just OMAP_PIN_INPUT is enough.
Cc: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
