Fixes in registers dump:
- Properly calculate dump length for 57712.
- Prevent HW blocks parity attentions when dumping registers in order to
prevent false parity errors handling.
- Update the bnx2x_dump.h file: old one had a few bugs that could cause
fatal HW error as a result of a registers dump.
Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't prevent RSS configuration in INT#x and MSI interrupt modes. Otherwise
Rx hash key won't be available.
Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Failure to call release_firmware() will result in memory leak in
drivers/atm/ambassador.c::ucode_init().
This patch makes sure we always call release_firmware() when needed,
thus removing the leak(s).
Yes, I know checkpatch complains about this patch, but it was either that
or completely mess up the existing style, so I opted to use the existing
style and live with the checkpatch related flak.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Failure to release_firmware() in drivers/net/hamradio/yam.c::add_mcs()
causes memory leak.
This patch should fix it.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to add mx28 dual fec support. Here are some key notes
for mx28 fec controller.
- The mx28 fec controller naming ENET-MAC is a different IP from FEC
used on other i.mx variants. But they are basically compatible
on software interface, so it's possible to share the same driver.
- ENET-MAC design on mx28 made an improper assumption that it runs
on a big-endian system. As the result, driver has to swap every
frame going to and coming from the controller.
- The external phys can only be configured by fec0, which means fec1
can not work independently and both phys need to be configured by
mii_bus attached on fec0.
- ENET-MAC reset will get mac address registers reset too.
- ENET-MAC MII/RMII mode and 10M/100M speed are configured
differently FEC.
- ETHER_EN bit must be set to get ENET-MAC interrupt work.
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The following commit made a fix to use fec_enet_open/fec_enet_close
over fec_enet_init/fec_stop for suspend/resume, because fec_enet_init
does not allow to have a working network interface at resume.
e3fe8558c7
net/fec: fix pm to survive to suspend/resume
This fix works for i.mx/mxc fec controller, but fails on mx28 fec
which gets a different interrupt logic design. On i.mx fec, interrupt
can be triggered even bit ETHER_EN of ECR register is not set. But
on mx28 fec, ETHER_EN must be set to get interrupt work. Meanwhile,
MII interrupt is mandatory to resume the driver, because MDIO
read/write changed to interrupt mode by commit below.
97b72e4320
fec: use interrupt for MDIO completion indication
fec_restart/fec_stop comes out as the solution working for both
cases.
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add mac field into fec_platform_data and consolidate function
fec_get_mac to get mac address in following order.
1) module parameter via kernel command line fec.macaddr=0x00,0x04,...
2) from flash in case of CONFIG_M5272 or fec_platform_data mac
field for others, which typically have mac stored in fuse
3) fec mac address registers set by bootloader
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The "index" becomes legacy since fep->pdev->id starts working
to identify the instance.
Moreover, the call of fec_enet_init(ndev, 0) always passes 0
to fep->index. This makes the following code in fec_get_mac buggy.
/* Adjust MAC if using default MAC address */
if (iap == fec_mac_default)
dev->dev_addr[ETH_ALEN-1] = fec_mac_default[ETH_ALEN-1] + fep->index;
It may be the time to remove "index" and use fep->pdev->id instead.
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
FEC_MMFR_OP_WRITE should be used than FEC_MMFR_OP_READ in
a mdio write operation.
It's probably a typo introduced by commit:
e6b043d512
netdev/fec.c: add phylib supporting to enable carrier detection (v2)
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/hch/hfsplus:
hfsplus: %L-to-%ll, macro correction, and remove unneeded braces
hfsplus: spaces/indentation clean-up
hfsplus: C99 comments clean-up
hfsplus: over 80 character lines clean-up
hfsplus: fix an artifact in ioctl flag checking
hfsplus: flush disk caches in sync and fsync
hfsplus: optimize fsync
hfsplus: split up inode flags
hfsplus: write up fsync for directories
hfsplus: simplify fsync
hfsplus: avoid useless work in hfsplus_sync_fs
hfsplus: make sure sync writes out all metadata
hfsplus: use raw bio access for partition tables
hfsplus: use raw bio access for the volume headers
hfsplus: always use hfsplus_sync_fs to write the volume header
hfsplus: silence a few debug printks
hfsplus: fix option parsing during remount
Fix up conflicts due to VFS changes in fs/hfsplus/{hfsplus_fs.h,unicode.c}
* 'next-spi' of git://git.secretlab.ca/git/linux-2.6: (77 commits)
spi/omap: Fix DMA API usage in OMAP MCSPI driver
spi/imx: correct the test on platform_get_irq() return value
spi/topcliff: Typo fix threhold to threshold
spi/dw_spi Typo change diable to disable.
spi/fsl_espi: change the read behaviour of the SPIRF
spi/mpc52xx-psc-spi: move probe/remove to proper sections
spi/dw_spi: add DMA support
spi/dw_spi: change to EXPORT_SYMBOL_GPL for exported APIs
spi/dw_spi: Fix too short timeout in spi polling loop
spi/pl022: convert running variable
spi/pl022: convert busy flag to a bool
spi/pl022: pass the returned sglen to the DMA engine
spi/pl022: map the buffers on the DMA engine
spi/topcliff_pch: Fix data transfer issue
spi/imx: remove autodetection
spi/pxa2xx: pass of_node to spi device and set a parent device
spi/pxa2xx: Modify RX-Tresh instead of busy-loop for the remaining RX bytes.
spi/pxa2xx: Add chipselect support for Sodaville
spi/pxa2xx: Consider CE4100's FIFO depth
spi/pxa2xx: Add CE4100 support
...
* 'for-2.6.38' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/percpu: (30 commits)
gameport: use this_cpu_read instead of lookup
x86: udelay: Use this_cpu_read to avoid address calculation
x86: Use this_cpu_inc_return for nmi counter
x86: Replace uses of current_cpu_data with this_cpu ops
x86: Use this_cpu_ops to optimize code
vmstat: User per cpu atomics to avoid interrupt disable / enable
irq_work: Use per cpu atomics instead of regular atomics
cpuops: Use cmpxchg for xchg to avoid lock semantics
x86: this_cpu_cmpxchg and this_cpu_xchg operations
percpu: Generic this_cpu_cmpxchg() and this_cpu_xchg support
percpu,x86: relocate this_cpu_add_return() and friends
connector: Use this_cpu operations
xen: Use this_cpu_inc_return
taskstats: Use this_cpu_ops
random: Use this_cpu_inc_return
fs: Use this_cpu_inc_return in buffer.c
highmem: Use this_cpu_xx_return() operations
vmstat: Use this_cpu_inc_return for vm statistics
x86: Support for this_cpu_add, sub, dec, inc_return
percpu: Generic support for this_cpu_add, sub, dec, inc_return
...
Fixed up conflicts: in arch/x86/kernel/{apic/nmi.c, apic/x2apic_uv_x.c, process.c}
as per Tejun.
* 'for-2.6.38' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq: (33 commits)
usb: don't use flush_scheduled_work()
speedtch: don't abuse struct delayed_work
media/video: don't use flush_scheduled_work()
media/video: explicitly flush request_module work
ioc4: use static work_struct for ioc4_load_modules()
init: don't call flush_scheduled_work() from do_initcalls()
s390: don't use flush_scheduled_work()
rtc: don't use flush_scheduled_work()
mmc: update workqueue usages
mfd: update workqueue usages
dvb: don't use flush_scheduled_work()
leds-wm8350: don't use flush_scheduled_work()
mISDN: don't use flush_scheduled_work()
macintosh/ams: don't use flush_scheduled_work()
vmwgfx: don't use flush_scheduled_work()
tpm: don't use flush_scheduled_work()
sonypi: don't use flush_scheduled_work()
hvsi: don't use flush_scheduled_work()
xen: don't use flush_scheduled_work()
gdrom: don't use flush_scheduled_work()
...
Fixed up trivial conflict in drivers/media/video/bt8xx/bttv-input.c
as per Tejun.
* 'sched-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
sched: Constify function scope static struct sched_param usage
sched: Fix strncmp operation
sched: Move sched_autogroup_exit() to free_signal_struct()
sched: Fix struct autogroup memory leak
sched: Mark autogroup_init() __init
sched: Consolidate the name of root_task_group and init_task_group
* 'x86-apic-cleanups-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: apic: Cleanup and simplify setup_local_APIC()
x86: Further simplify mp_irq info handling
x86: Unify 3 similar ways of saving mp_irqs info
x86, ioapic: Avoid writing io_apic id if already correct
x86, x2apic: Don't map lapic addr for preenabled x2apic systems
x86, sfi: Use register_lapic_address()
x86, apic: Use register_lapic_address() in init_apic_mapping()
x86, apic: Remove early_init_lapic_mapping()
x86, apic: Unify identical register_lapic_address() functions
* 'rmobile-latest' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6: (67 commits)
ARM: mach-shmobile: update for SMP changes.
ARM: mach-shmobile: update for GIC changes.
ARM: mach-shmobile: Fix up clkdev fallout for SH73A0.
dma: shdma: don't register the global die notifier multiple times
ARM: mach-shmobile: Rely on run-time IRQ handlers
ARM: mach-shmobile: Run-time IRQ handler for GIC
ARM: mach-shmobile: Run-time IRQ handler for INTCA
ARM: mach-shmobile: Enable CONFIG_MULTI_IRQ_HANDLER
ARM: mach-shmobile: Use shared GIC entry macros
ARM: mach-shmobile: mackerel: Add zboot support
ARM: mach-shmobile: mackerel: Add HDMI sound support
ARM: mach-shmobile: mackerel: add HDMI video support
ARM: mach-shmobile: ap4evb: fixup clk_put timing of fsib_clk
ARM: mach-shmobile: sh73a0: fix div4 table
ARM: mach-shmobile: ap4/mackerel: modify wrong comment out of USB
ARM: mach-shmobile: Mackerel VGA camera support
mmc: sh_mmcif: make DMA support by the driver unconditional
ARM: mach-shmobile: Add eMMC support through MMCIF on AG5EVM
ARM: mach-shmobile: Use pullups for AG5EVM KEYSC pins
ARM: mach-shmobile: sh73a0 GPIO pullup improvement
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (58 commits)
Input: wacom_w8001 - support pen or touch only devices
Input: wacom_w8001 - use __set_bit to set keybits
Input: bu21013_ts - fix misuse of logical operation in place of bitop
Input: i8042 - add Acer Aspire 5100 to the Dritek list
Input: wacom - add support for digitizer in Lenovo W700
Input: psmouse - disable the synaptics extension on OLPC machines
Input: psmouse - fix up Synaptics comment
Input: synaptics - ignore bogus mt packet
Input: synaptics - add multi-finger and semi-mt support
Input: synaptics - report clickpad property
input: mt: Document interface updates
Input: fix double equality sign in uevent
Input: introduce device properties
hid: egalax: Add support for Wetab (726b)
Input: include MT library as source for kerneldoc
MAINTAINERS: Update input-mt entry
hid: egalax: Add support for Samsung NB30 netbook
hid: egalax: Document the new devices in Kconfig
hid: egalax: Add support for Wetab
hid: egalax: Convert to MT slots
...
Fixed up trivial conflict in drivers/input/keyboard/Kconfig
* 'tty-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty-2.6: (36 commits)
serial: apbuart: Fixup apbuart_console_init()
TTY: Add tty ioctl to figure device node of the system console.
tty: add 'active' sysfs attribute to tty0 and console device
drivers: serial: apbuart: Handle OF failures gracefully
Serial: Avoid unbalanced IRQ wake disable during resume
tty: fix typos/errors in tty_driver.h comments
pch_uart : fix warnings for 64bit compile
8250: fix uninitialized FIFOs
ip2: fix compiler warning on ip2main_pci_tbl
specialix: fix compiler warning on specialix_pci_tbl
rocket: fix compiler warning on rocket_pci_ids
8250: add a UPIO_DWAPB32 for 32 bit accesses
8250: use container_of() instead of casting
serial: omap-serial: Add support for kernel debugger
serial: fix pch_uart kconfig & build
drivers: char: hvc: add arm JTAG DCC console support
RS485 documentation: add 16C950 UART description
serial: ifx6x60: fix memory leak
serial: ifx6x60: free IRQ on error
Serial: EG20T: add PCH_UART driver
...
Fixed up conflicts in drivers/serial/apbuart.c with evil merge that
makes the code look fairly sane (unlike either side).
* 'usb-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (144 commits)
USB: add support for Dream Cheeky DL100B Webmail Notifier (1d34:0004)
USB: serial: ftdi_sio: add support for TIOCSERGETLSR
USB: ehci-mxc: Setup portsc register prior to accessing OTG viewport
USB: atmel_usba_udc: fix freeing irq in usba_udc_remove()
usb: ehci-omap: fix tll channel enable mask
usb: ohci-omap3: fix trivial typo
USB: gadget: ci13xxx: don't assume that PAGE_SIZE is 4096
USB: gadget: ci13xxx: fix complete() callback for no_interrupt rq's
USB: gadget: update ci13xxx to work with g_ether
USB: gadgets: ci13xxx: fix probing of compiled-in gadget drivers
Revert "USB: musb: pm: don't rely fully on clock support"
Revert "USB: musb: blackfin: pm: make it work"
USB: uas: Use GFP_NOIO instead of GFP_KERNEL in I/O submission path
USB: uas: Ensure we only bind to a UAS interface
USB: uas: Rename sense pipe and sense urb to status pipe and status urb
USB: uas: Use kzalloc instead of kmalloc
USB: uas: Fix up the Sense IU
usb: musb: core: kill unneeded #include's
DA8xx: assign name to MUSB IRQ resource
usb: gadget: g_ncm added
...
Manually fix up trivial conflicts in USB Kconfig changes in:
arch/arm/mach-omap2/Kconfig
arch/sh/Kconfig
drivers/usb/Kconfig
drivers/usb/host/ehci-hcd.c
and annoying chip clock data conflicts in:
arch/arm/mach-omap2/clock3xxx_data.c
arch/arm/mach-omap2/clock44xx_data.c
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (147 commits)
[SCSI] arcmsr: fix write to device check
[SCSI] lpfc: lower stack use in lpfc_fc_frame_check
[SCSI] eliminate an unnecessary local variable from scsi_remove_target()
[SCSI] libiscsi: use bh locking instead of irq with session lock
[SCSI] libiscsi: do not take host lock in queuecommand
[SCSI] be2iscsi: fix null ptr when accessing task hdr
[SCSI] be2iscsi: fix gfp use in alloc_pdu
[SCSI] libiscsi: add more informative failure message during iscsi scsi eh
[SCSI] gdth: Add missing call to gdth_ioctl_free
[SCSI] bfa: remove unused defintions and misc cleanups
[SCSI] bfa: remove inactive functions
[SCSI] bfa: replace bfa_assert with WARN_ON
[SCSI] qla2xxx: Use sg_next to fetch next sg element while walking sg list.
[SCSI] qla2xxx: Fix to avoid recursive lock failure during BSG timeout.
[SCSI] qla2xxx: Remove code to not reset ISP82xx on failure.
[SCSI] qla2xxx: Display mailbox register 4 during 8012 AEN for ISP82XX parts.
[SCSI] qla2xxx: Don't perform a BIG_HAMMER if Get-ID (0x20) mailbox command fails on CNAs.
[SCSI] qla2xxx: Remove redundant module parameter permission bits
[SCSI] qla2xxx: Add sysfs node for displaying board temperature.
[SCSI] qla2xxx: Code cleanup to remove unwanted comments and code.
...
There was a semi-colon missing and it broke the compile.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Running the latest kernel on the 4430SDP board with DMA API debugging
enabled results in this:
WARNING: at lib/dma-debug.c:803 check_unmap+0x19c/0x6f0()
NULL NULL: DMA-API: device driver tries to free DMA memory it has not allocated
[device address=0x000000008129901a] [size=260 bytes]
Modules linked in:
Backtrace:
[<c003cbe0>] (dump_backtrace+0x0/0x10c) from [<c0278da8>] (dump_stack+0x18/0x1c)
r7:c1839dc0 r6:c0198578 r5:c0304b17 r4:00000323
[<c0278d90>] (dump_stack+0x0/0x1c) from [<c005b158>] (warn_slowpath_common+0x58/0x70)
[<c005b100>] (warn_slowpath_common+0x0/0x70) from [<c005b214>] (warn_slowpath_fmt+0x38/0x40)
r8:c1839e40 r7:00000000 r6:00000104 r5:00000000 r4:8129901a
[<c005b1dc>] (warn_slowpath_fmt+0x0/0x40) from [<c0198578>] (check_unmap+0x19c/0x6f0)
r3:c03110de r2:c0304e6b
[<c01983dc>] (check_unmap+0x0/0x6f0) from [<c0198cd8>] (debug_dma_unmap_page+0x74/0x80)
[<c0198c64>] (debug_dma_unmap_page+0x0/0x80) from [<c01d5ad8>] (omap2_mcspi_work+0x514/0xbf0)
[<c01d55c4>] (omap2_mcspi_work+0x0/0xbf0) from [<c006dfb0>] (process_one_work+0x294/0x400)
[<c006dd1c>] (process_one_work+0x0/0x400) from [<c006e50c>] (worker_thread+0x220/0x3f8)
[<c006e2ec>] (worker_thread+0x0/0x3f8) from [<c00738d0>] (kthread+0x88/0x90)
[<c0073848>] (kthread+0x0/0x90) from [<c005e924>] (do_exit+0x0/0x5fc)
r7:00000013 r6:c005e924 r5:c0073848 r4:c1829ee0
---[ end trace 1b75b31a2719ed20 ]---
I've no idea why this driver uses NULL for dma_unmap_single instead of
the &spi->dev that is laying around just waiting to be used in that
function - but it's an easy fix.
Also replace this comment with a FIXME comment:
/* Do DMA mapping "early" for better error reporting and
* dcache use. Note that if dma_unmap_single() ever starts
* to do real work on ARM, we'd need to clean up mappings
* for previous transfers on *ALL* exits of this loop...
*/
as the comment is not true - we do work in dma_unmap() functions,
particularly on ARMv6 and above. I've corrected the existing unmap
functions but if any others are required they must be added ASAP.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The test "if (spi_imx->irq <= 0)" is not testing the IRQ value, but
the return value of platform_get_irq(). As platform_get_irq() can
return an error (-ENXIO) or the IRQ value it found, the test should be
"if (spi_imx->irq < 0)"
[grant.likely: Note: In general, Linux irq number 0 should also mean
no irq, but arm still allows devices to be assigned 0, and the imx
platform uses 0 for one of the spi devices, so this patch is needed
for the device to work]
Signed-off-by: Richard Genoud <richard.genoud@gmail.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Function-scope statics are discouraged because they are
easily overlooked and can cause subtle bugs/races due to
their global (non-SMP safe) nature.
Linus noticed that we did this for sched_param - at minimum
make the const.
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: Message-ID: <AANLkTinotRxScOHEb0HgFgSpGPkq_6jKTv5CfvnQM=ee@mail.gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
One of the operands, buf, is incorrect, since it is stripped and the
correct address for subsequent string comparing could change if
leading white spaces, if any, are removed from buf.
It is fixed by replacing buf with cmp.
Signed-off-by: Hillf Danton <dhillf@gmail.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <AANLkTinOPuYsVovrZpbuCCmG5deEyc8WgA_A1RJx_YK7@mail.gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Seems I lost a change somewhere, leaking memory.
sched: fix struct autogroup memory leak
Add missing change to actually use autogroup_free().
Signed-off-by: Mike Galbraith <efault@gmx.de>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <1294222285.8369.2.camel@marge.simson.net>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
autogroup_init() is only called at boot time.
Signed-off-by: Yong Zhang <yong.zhang0@gmail.com>
Cc: Mike Galbraith <efault@gmx.de>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <1294375425-31065-1-git-send-email-yong.zhang0@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
root_task_group is the leftover of USER_SCHED, now it's always
same to init_task_group.
But as Mike suggested, root_task_group is maybe the suitable name
to keep for a tree.
So in this patch:
init_task_group --> root_task_group
init_task_group_load --> root_task_group_load
INIT_TASK_GROUP_LOAD --> ROOT_TASK_GROUP_LOAD
Suggested-by: Mike Galbraith <efault@gmx.de>
Signed-off-by: Yong Zhang <yong.zhang0@gmail.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <20110107071736.GA32635@windriver.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Conflicts:
arch/x86/include/asm/io_apic.h
Merge reason: Resolve the conflict, update to a more recent -rc base
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The 'seq_window' sysctl sets the initial value for the DCCP Sequence Window,
which may range from 32..2^46-1 (RFC 4340, 7.5.2). The patch sets the upper
bound consistently to 2^32-1 on both 32 and 64 bit systems, which should be
sufficient - with a RTT of 1sec and 1-byte packets, a seq_window of 2^32-1
corresponds to a link speed of 34 Gbps.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Currently dccp_check_seqno allows any valid packet to update the Greatest
Sequence Number Received, even if that packet's sequence number is less than
the current GSR. This patch adds a check to make sure that the new packet's
sequence number is greater than GSR.
Signed-off-by: Samuel Jero <sj323707@ohio.edu>
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Currently dccp_check_seqno returns 0 (indicating a valid packet) if the
acknowledgment number is out of bounds and the sync that RFC 4340 mandates at
this point is currently being rate-limited. This function should return -1,
indicating an invalid packet.
Signed-off-by: Samuel Jero <sj323707@ohio.edu>
Acked-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Minor formatting fixup since the information which core was associated
with the MCE is not always valid.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Building for X86_32 produces shift count warnings, so use BIT_64() to
eliminate the warnings.
drivers/edac/mce_amd.c:778: warning: left shift count >= width of type
drivers/edac/mce_amd.c:778: warning: left shift count >= width of type
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Doug Thompson <dougthompson@xmission.com>
Cc: bluesmoke-devel@lists.sourceforge.net
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Now that everything is inplace, enable MCE decoding on F15h. Make
initcall routine a bit more readable.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Shorten up MCi_STATUS flags and add BD's new deferred and poison types.
Also, simplify formatting.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
MCE bank 2 is redefined from a BU to a CU (Combined Unit) bank on F15h.
Add a decoder function for CU MCEs.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Add a decoder for F15h DC MCEs to support the new types of DC MCEs
introduced by the BD microarchitecture.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
