Once pm_runtime_set_active() gets called, the kernel assumes that given
device has already enabled runtime pm and will call pm_runtime_suspend()
without matching pm_runtime_resume(). In case of DRM FIMC IPP driver,
this will result in calling clk_disable() without respective call to
clk_enable(). This patch removes call to pm_runtime_set_active() to
ensure that pm_runtime_suspend/resume calls will match.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
INT_EN cache field was updated only by mixer_enable_vblank.
The patch adds update also by mixer_disable_vblank function.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
The driver used incorrect flags to clear interrupt status.
The patch fixes it.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
edid returned by drm_get_edid should be freed.
The patch fixes it.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
The bits for rotation are not used as exclusively. So GSC_IN_ROT_270 can
not be used for swap detection. The definition of it is same with
GSC_IN_ROT_MASK. It is enough to check GSC_IN_ROT_90 bit is set or not to
check whether width / height size swapping is needed.
Signed-off-by: Hyungwon Hwang <human.hwang@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
On some board, TE GPIO should be configured properly thoughout pinctrl driver
as an wakeup interrupt. So this gpio should be configurable in the board's DT,
not being requested as a input pin.
Signed-off-by: Hyungwon Hwang <human.hwang@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
MIC must be initilized by MIPI DSI when it is being bound.
Signed-off-by: Hyungwon Hwang <human.hwang@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
This patch make the driver to use an array for clock access. The number
of clocks are different from the existing MIPI DSI driver and Exynos5433
MIPI DSI driver. So this patch is needed before adding support for
Exynos5433 MIPI DSI driver.
Signed-off-by: Hyungwon Hwang <human.hwang@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Exynos MIPI DSI driver uses some static values such as address offsets,
register setting values, and etc. This patch makes the driver get those
values from the driver data.
Signed-off-by: Hyungwon Hwang <human.hwang@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
This patch adds macros for register writing/reading. This is needed for
adding support Exynos5433 MIPI DSI driver, not by using if statement, but
by using driver data.
Signed-off-by: Hyungwon Hwang <human.hwang@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
This patch renames pll_clk to sclk_clk. The clock referenced by pll_clk
is actually not the pll input clock for dsi. The pll input clock comes
from the board's oscillator directly. But for the backward
compatibility, the old clock name "pll_clk" is also OK.
Signed-off-by: Hyungwon Hwang <human.hwang@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
MIC(Mobile image compressor) is newly added IP in Exynos5433. MIC
resides between decon and mipi dsim, and compresses frame data by 50%.
With dsi, not display port, to send frame data to the panel, the
bandwidth is not enough. That is why this compressor is introduced.
Signed-off-by: Hyungwon Hwang <human.hwang@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
DECON(Display and Enhancement Controller) is new IP replacing FIMD in
Exynos5433. This patch adds Exynos5433 decon driver.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Hyungwon Hwang <human.hwang@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
This patch is a preparation patch for adding support for Exynos5433
DECON. Exynos7 DECON have to be distinguished from Exynos5433 DECON.
Signed-off-by: Hyungwon Hwang <human.hwang@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Every CRTC drivers in Exynos DRM implements the code which checks
whether IOMMU is supported or not, and if supported enable it.
Making new helper for it generalize each CRTC drivers.
Signed-off-by: Hyungwon Hwang <human.hwang@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Without this dependency, Kbuild is confused and the configs below
them are not placed under Exynos DRM. This patch fixes it, so the
configs below them become to be placed under Exynos DRM.
Signed-off-by: Hyungwon Hwang <human.hwang@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
This dependency is a historical thing. It is added when this DP driver is
under media subsystem. Now because it is under Exynos DRM, this dependency
is not needed anymore.
Signed-off-by: Hyungwon Hwang <human.hwang@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
This patch resolves the issue that refresh rate got low
at extension mode test with fimd and vidi combination.
The problem was because atomic_commit callback waited
for the completion of vblank to gaurantee crtc relevant
registers are updated from shadow registers to real ones.
However, the waiting there is really unnecessary because
page flip operation does already it.
Signed-off-by: Inki Dae <inki.dae@samsung.com>
The field 'vma' of 'exynos_drm_gem_obj' structure was introduced in
2a3098ff6c ("drm/exynos: add userptr feature for g2d module") but is
not referenced anywhere.
One instance of 'exynos_drm_gem_obj' may be mapped to multiple
user-space VMAs so 'vma' field does not look useful anyway.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
This patch resolves page fault issue with iommu and atomic feature
when modetest test application is terminated.
ENWIN_F field of WINCONx register enables or disable a dma channel to
each hardware overlay - the value of the field will be updated to real
register after vsync.
So this patch makes sure the dma channel is disabled by waiting for vsync
one time after clearing shadow registers to all dma channels.
Below shows the page fault issue:
setting mode 720x1280-60Hz@XR24 on connectors 31, crtc 29
freq: 59.99Hz
[ 34.831025] PAGE FAULT occurred at 0x20400000 by 11e20000.sysmmu(Page
table base: 0x6e324000)
[ 34.838072] Lv1 entry: 0x6e92dc01
[ 34.841489] ------------[ cut here ]------------
[ 34.846058] kernel BUG at drivers/iommu/exynos-iommu.c:364!
[ 34.851614] Internal error: Oops - BUG: 0 [#1] PREEMPT SMP ARM
[ 34.857428] Modules linked in:
<--snip-->
[ 35.210894] [<c02880d0>] (exynos_sysmmu_irq) from [<c00608f8>]
(handle_irq_event_percpu+0x78/0x134)
[ 35.219914] [<c00608f8>] (handle_irq_event_percpu) from [<c00609f0>]
(handle_irq_event+0x3c/0x5c)
[ 35.228768] [<c00609f0>] (handle_irq_event) from [<c0063698>]
(handle_level_irq+0xc4/0x13c)
[ 35.237101] [<c0063698>] (handle_level_irq) from [<c005ff7c>]
(generic_handle_irq+0x2c/0x3c)
[ 35.245521] [<c005ff7c>] (generic_handle_irq) from [<c02214ec>]
(combiner_handle_cascade_irq+0x94/0x100)
[ 35.254980] [<c02214ec>] (combiner_handle_cascade_irq) from
[<c005ff7c>] (generic_handle_irq+0x2c/0x3c)
[ 35.264353] [<c005ff7c>] (generic_handle_irq) from [<c0060248>]
(__handle_domain_irq+0x7c/0xec)
[ 35.273034] [<c0060248>] (__handle_domain_irq) from [<c0009434>]
(gic_handle_irq+0x30/0x68)
[ 35.281366] [<c0009434>] (gic_handle_irq) from [<c0012ec0>]
(__irq_svc+0x40/0x74)
Signed-off-by: Inki Dae <inki.dae@samsung.com>
DRM Exynos driver is relying on dma-mapping internal structures when used
with IOMMU enabled. This patch partially hides dma-mapping internal things
by using proper get_dma_ops/set_dma_ops calls.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
This patch adds code, which detach sub-device nodes from default iommu
domain if such has been configured. This lets Exynos DRM driver to properly
attach sub-devices to its own, common for all sub-devices domain.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
One should not do any assumptions on the stare of the fimd hardware
during driver initialization, so to properly reset fimd before enabling
IOMMU, one should ensure that all power domains and clocks are really
enabled. This patch adds pm_runtime and clocks management in the
fimd_clear_channel() function to ensure that any access to fimd
registers will be performed with clocks and power domains enabled.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
When the fimd is disabled by fimd_disable(), enabled overlay layers also
are disabled. If clocks for fimd are enabled by fimd_enable() on this
case, it can lead IOMMU page fault. The reason is that VIDCON0_ENVID and
VIDCON0_ENVID_F bits of VIDCON0 register are set still even though fimd
is disabled, so it may continue display output of prior when clocks for
fimd are enabled again.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
With atomic modesetting all the control for CRTC, Planes, Encoders and
Connectors should come from DRM core, so the driver is not allowed to
enable or disable planes from inside the crtc_enable()/disable() call.
But it needs to disable planes with crtc_disable in exynos driver
internally. Because crtc is disabled before plane is disabled, it means
plane_disable just returns without any register changes, then we cannot
be sure setting register to disable plane when crtc is disable.
This patch removes this chainned calls to enable plane from exynos hw
drivers code letting only DRM core touch planes except to disable plane.
Also it leads eliminable enabled and resume of struct exynos_drm_plane.
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
The reason waiting vblank is to be power gated and disabled clocks after
dma operation is completed. The dma operation is stopped already before
be power gated and clocks are disabled when mixer is disabled by commit
381be025ac1a6("drm/exynos: stop mixer before gating clocks during
poweroff"). Don't need to wait vblank anymore.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
FIMC & GSC driver can calculate the offset of planes. So there are
use cases which IPP receives just one GEM handle of an image with
multiple plane. This patch extends ipp_validate_mem_node() to validate
this case.
Signed-off-by: Hyungwon Hwang <human.hwang@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Config depends on the opreation. So it must be referenced by an
operation id, not a property id.
Signed-off-by: Hyungwon Hwang <human.hwang@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
SoC checking code is not necessary anymore, as exynos_drm_match_add and
exynos_drm_platform_probe already properly handles situation when there are
no Exynos DRM components.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Tested-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
In case there are multiple pipelines and deferred probe occurs, only components
of the first pipeline were bound. As a result only one pipeline was available.
The main cause of this issue was dynamic generation of component match table -
every component driver during probe registered itself on helper list, if there
was at least one pipeline present on this list component match table were
created without deferred components.
This patch removes this helper list, instead it creates match table from
existing devices requiring exynos_drm KMS drivers. This way match table do not
depend on probe/deferral order and contains all KMS components.
As a side effect patch makes the code cleaner and significantly smaller.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Code registering different drivers and simple platform devices was dispersed
across multiple sub-modules. This patch moves it to one place. As a result
initialization code is shorter and cleaner and should simplify further
development.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
This patch makes one of Linux framebuffer and DRM CRTC drivers
to be enabled.
Display controllers, FIMD and DECON, can be controlled by Linux
framebuffer or DRM CRTC drivers so only one of them should be
enabled.
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Reviewed-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
To follow more closely the new atomic API we split the dpms()
helper into the enable() and disable() helper to get exactly the
same semantics.
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
The planes are already disabled by the drm_atomic_helper_commit() code
so we don't need to disable the in these two places.
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Reviewed-by: Joonyoung Shim <jy0922.shim@samsung.com>
Tested-by: Tobias Jakobi <tjakobi@math.uni-bielefeld.de>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Run dpms operations through the atomic intefaces. This basically removes
the .dpms() callback from econders and crtcs and use .disable() and
.enable() to turn the crtc on and off.
v2: Address comments by Joonyoung:
- make hdmi code call ->disable() instead of ->dpms()
- do not use WARN_ON on crtc enable/disable
v3: - Fix build failure after the hdmi change in v2
- Change dpms helper of ptn3460 bridge
v4: - remove win_commit() call from .enable()
v5: - move .atomic_check() to the atomic PageFlip patch, and transform it
in .atomic_begin()
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Reviewed-by: Joonyoung Shim <jy0922.shim@samsung.com>
Tested-by: Tobias Jakobi <tjakobi@math.uni-bielefeld.de>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
exynos needs to update planes with the crtc enabled (mainly for the FIMD
case) so this specific atomic commit changes the order of
drm_atomic_helper_commit_modeset_enables() and
drm_atomic_helper_commit_planes() to commit planes after we enable crtc
and encoders.
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
This is a preparation commit to move exynos_drm_crtc_disable() together
with the future exynos_drm_crtc_enable() that will come from the split of
exynos_drm_crtc_dpms() callback.
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Now that no one is using the functions exported by exynos_drm_plane due
to the atomic conversion we can make remove some of the them or make them
static.
v2: remove unused exynos_drm_crtc
v3: fix checkpatch error (reported by Joonyoung)
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Reviewed-by: Joonyoung Shim <jy0922.shim@samsung.com>
Tested-by: Tobias Jakobi <tjakobi@math.uni-bielefeld.de>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
PageFlips now use the atomic helper to work through the atomic modesetting
API. Async page flips are not supported yet.
v2: Add .atomic_begin() step to handle the vblank part we removed from
exynos page_flip code.
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Reviewed-by: Joonyoung Shim <jy0922.shim@samsung.com>
Tested-by: Tobias Jakobi <tjakobi@math.uni-bielefeld.de>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Now that phase 1 and 2 are complete switch .set_config helper to
use the atomic one.
v2: also remove .prepare() callback
v3: remove .mode_set() and .mode_set_base() and encoder's
.prepare() callbacks
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Reviewed-by: Joonyoung Shim <jy0922.shim@samsung.com>
Tested-by: Tobias Jakobi <tjakobi@math.uni-bielefeld.de>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Now that phase 1 and 2 are complete we can switch the update/disable_plane
callbacks to their atomic version.
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Reviewed-by: Joonyoung Shim <jy0922.shim@samsung.com>
Tested-by: Tobias Jakobi <tjakobi@math.uni-bielefeld.de>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Use drm_atomic_set_fb_for_plane() in the legacy page_flip path to keep
track of the framebuffer pointer and reference.
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Reviewed-by: Joonyoung Shim <jy0922.shim@samsung.com>
Tested-by: Tobias Jakobi <tjakobi@math.uni-bielefeld.de>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Set CRTC, planes and connectors to use the default implementations from
the atomic helper library. The helpers will work to keep track of state
for each DRM object.
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Reviewed-by: Joonyoung Shim <jy0922.shim@samsung.com>
Tested-by: Tobias Jakobi <tjakobi@math.uni-bielefeld.de>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Handle changes by removing copy from adjusted_mode to mode as using
adjusted_mode of crtc_state.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
