This is a merge error on my part - the driver was merged into mainline
by commit c5951e7c8e ("Merge tag 'mips_5.6' of git://../mips/linux")
over a week ago, but nobody apparently noticed that it didn't actually
build due to still having a reference to the devm_ioremap_nocache()
function, removed a few days earlier through commit 6a1000bd27 ("Merge
tag 'ioremap-5.6' of git://../ioremap").
Apparently this didn't get any build testing anywhere. Not perhaps all
that surprising: it's restricted to 64-bit MIPS only, and only with the
new SGI_MFD_IOC3 support enabled.
I only noticed because the ioremap conflicts in the ARM SoC driver
update made me check there weren't any others hiding, and I found this
one.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Various driver updates for platforms:
- Nvidia: Fuse support for Tegra194, continued memory controller pieces
for Tegra30
- NXP/FSL: Refactorings of QuickEngine drivers to support ARM/ARM64/PPC
- NXP/FSL: i.MX8MP SoC driver pieces
- TI Keystone: ring accelerator driver
- Qualcomm: SCM driver cleanup/refactoring + support for new SoCs.
- Xilinx ZynqMP: feature checking interface for firmware. Mailbox
communication for power management
- Overall support patch set for cpuidle on more complex hierarchies
(PSCI-based)
+ Misc cleanups, refactorings of Marvell, TI, other platforms.
-----BEGIN PGP SIGNATURE-----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=ONtb
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC-related driver updates from Olof Johansson:
"Various driver updates for platforms:
- Nvidia: Fuse support for Tegra194, continued memory controller
pieces for Tegra30
- NXP/FSL: Refactorings of QuickEngine drivers to support
ARM/ARM64/PPC
- NXP/FSL: i.MX8MP SoC driver pieces
- TI Keystone: ring accelerator driver
- Qualcomm: SCM driver cleanup/refactoring + support for new SoCs.
- Xilinx ZynqMP: feature checking interface for firmware. Mailbox
communication for power management
- Overall support patch set for cpuidle on more complex hierarchies
(PSCI-based)
and misc cleanups, refactorings of Marvell, TI, other platforms"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (166 commits)
drivers: soc: xilinx: Use mailbox IPI callback
dt-bindings: power: reset: xilinx: Add bindings for ipi mailbox
drivers: soc: ti: knav_qmss_queue: Pass lockdep expression to RCU lists
MAINTAINERS: Add brcmstb PCIe controller entry
soc/tegra: fuse: Unmap registers once they are not needed anymore
soc/tegra: fuse: Correct straps' address for older Tegra124 device trees
soc/tegra: fuse: Warn if straps are not ready
soc/tegra: fuse: Cache values of straps and Chip ID registers
memory: tegra30-emc: Correct error message for timed out auto calibration
memory: tegra30-emc: Firm up hardware programming sequence
memory: tegra30-emc: Firm up suspend/resume sequence
soc/tegra: regulators: Do nothing if voltage is unchanged
memory: tegra: Correct reset value of xusb_hostr
soc/tegra: fuse: Add APB DMA dependency for Tegra20
bus: tegra-aconnect: Remove PM_CLK dependency
dt-bindings: mediatek: add MT6765 power dt-bindings
soc: mediatek: cmdq: delete not used define
memory: tegra: Add support for the Tegra194 memory controller
memory: tegra: Only include support for enabled SoCs
memory: tegra: Support DVFS on Tegra186 and later
...
- Support mremap() for the VDSO, primarily to allow CRIU to restore the
VDSO to its checkpointed location.
- Restore the MIPS32 cBPF JIT, after having reverted the enablement of
the eBPF JIT for MIPS32 systems in the 5.5 cycle.
- Improve cop0 counter synchronization behaviour whilst onlining CPUs by
running with interrupts disabled.
- Better match FPU behaviour when emulating multiply-accumulate
instructions on pre-r6 systems that implement IEEE754-2008 style MACs.
- Loongson64 kernels now build using the MIPS64r2 ISA, allowing them to
take advantage of instructions introduced by r2.
- Support for the Ingenic X1000 SoC & the really nice little CU Neo
development board that's using it.
- Support for WMAC on GARDENA Smart Gateway devices.
- Lots of cleanup & refactoring of SGI IP27 (Origin 2*) support in
preparation for introducing IP35 (Origin 3*) support.
- Various Kconfig & Makefile cleanups.
-----BEGIN PGP SIGNATURE-----
iIwEABYIADQWIQRgLjeFAZEXQzy86/s+p5+stXUA3QUCXjRnpxYccGF1bGJ1cnRv
bkBrZXJuZWwub3JnAAoJED6nn6y1dQDdNYoA/3ZhgKX1L/hwvkPKwu7FxbL41pjB
WAm8IYDaxPvgxkcSAP9FNNepHK+oBPM8I2e3DvDvmcuYjumztdikzYbJ5HuMBA==
=MV2S
-----END PGP SIGNATURE-----
Merge tag 'mips_5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux
Pull MIPS changes from Paul Burton:
"Nothing too big or scary in here:
- Support mremap() for the VDSO, primarily to allow CRIU to restore
the VDSO to its checkpointed location.
- Restore the MIPS32 cBPF JIT, after having reverted the enablement
of the eBPF JIT for MIPS32 systems in the 5.5 cycle.
- Improve cop0 counter synchronization behaviour whilst onlining CPUs
by running with interrupts disabled.
- Better match FPU behaviour when emulating multiply-accumulate
instructions on pre-r6 systems that implement IEEE754-2008 style
MACs.
- Loongson64 kernels now build using the MIPS64r2 ISA, allowing them
to take advantage of instructions introduced by r2.
- Support for the Ingenic X1000 SoC & the really nice little CU Neo
development board that's using it.
- Support for WMAC on GARDENA Smart Gateway devices.
- Lots of cleanup & refactoring of SGI IP27 (Origin 2*) support in
preparation for introducing IP35 (Origin 3*) support.
- Various Kconfig & Makefile cleanups"
* tag 'mips_5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux: (60 commits)
MIPS: PCI: Add detection of IOC3 on IO7, IO8, IO9 and Fuel
MIPS: Loongson64: Disable exec hazard
MIPS: Loongson64: Bump ISA level to MIPSR2
MIPS: Make DIEI support as a config option
MIPS: OCTEON: octeon-irq: fix spelling mistake "to" -> "too"
MIPS: asm: local: add barriers for Loongson
MIPS: Loongson64: Select mac2008 only feature
MIPS: Add MAC2008 Support
Revert "MIPS: Add custom serial.h with BASE_BAUD override for generic kernel"
MIPS: sort MIPS and MIPS_GENERIC Kconfig selects alphabetically (again)
MIPS: make CPU_HAS_LOAD_STORE_LR opt-out
MIPS: generic: don't unconditionally select PINCTRL
MIPS: don't explicitly select LIBFDT in Kconfig
MIPS: sync-r4k: do slave counter synchronization with disabled HW interrupts
MIPS: SGI-IP30: Check for valid pointer before using it
MIPS: syscalls: fix indentation of the 'SYSNR' message
MIPS: boot: fix typo in 'vmlinux.lzma.its' target
MIPS: fix indentation of the 'RELOCS' message
dt-bindings: Document loongson vendor-prefix
MIPS: CU1000-Neo: Refresh defconfig to support HWMON and WiFi.
...
Here are the big set of tty and serial driver updates for 5.6-rc1
Included in here are:
- dummy_con cleanups (touches lots of arch code)
- sysrq logic cleanups (touches lots of serial drivers)
- samsung driver fixes (wasn't really being built)
- conmakeshash move to tty subdir out of scripts
- lots of small tty/serial driver updates
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXjFRBg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yn2VACgkge7vTeUNeZFc+6F4NWphAQ5tCQAoK/MMbU6
0O8ef7PjFwCU4s227UTv
=6m40
-----END PGP SIGNATURE-----
Merge tag 'tty-5.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial driver updates from Greg KH:
"Here are the big set of tty and serial driver updates for 5.6-rc1
Included in here are:
- dummy_con cleanups (touches lots of arch code)
- sysrq logic cleanups (touches lots of serial drivers)
- samsung driver fixes (wasn't really being built)
- conmakeshash move to tty subdir out of scripts
- lots of small tty/serial driver updates
All of these have been in linux-next for a while with no reported
issues"
* tag 'tty-5.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (140 commits)
tty: n_hdlc: Use flexible-array member and struct_size() helper
tty: baudrate: SPARC supports few more baud rates
tty: baudrate: Synchronise baud_table[] and baud_bits[]
tty: serial: meson_uart: Add support for kernel debugger
serial: imx: fix a race condition in receive path
serial: 8250_bcm2835aux: Document struct bcm2835aux_data
serial: 8250_bcm2835aux: Use generic remapping code
serial: 8250_bcm2835aux: Allocate uart_8250_port on stack
serial: 8250_bcm2835aux: Suppress register_port error on -EPROBE_DEFER
serial: 8250_bcm2835aux: Suppress clk_get error on -EPROBE_DEFER
serial: 8250_bcm2835aux: Fix line mismatch on driver unbind
serial_core: Remove unused member in uart_port
vt: Correct comment documenting do_take_over_console()
vt: Delete comment referencing non-existent unbind_con_driver()
arch/xtensa/setup: Drop dummy_con initialization
arch/x86/setup: Drop dummy_con initialization
arch/unicore32/setup: Drop dummy_con initialization
arch/sparc/setup: Drop dummy_con initialization
arch/sh/setup: Drop dummy_con initialization
arch/s390/setup: Drop dummy_con initialization
...
The main irq handler function starts by first masking disabled
interrupts in the status register values to ensure to only handle
enabled interrupts. This is important as when the RX path in the
hardware is disabled reading the RX fifo results in an external abort.
This checking must be done under the port lock, otherwise the following
can happen:
CPU1 | CPU2
|
irq triggers as there are chars |
in the RX fifo |
| grab port lock
imx_uart_int finds RRDY enabled |
and calls imx_uart_rxint which |
has to wait for port lock |
| disable RX (e.g. because we're
| using RS485 with !RX_DURING_TX)
|
| release port lock
read from RX fifo with RX |
disabled => exception |
So take the port lock only once in imx_uart_int() instead of in the
functions called from there.
Reported-by: Andre Renaud <arenaud@designa-electronics.com>
Cc: stable@vger.kernel.org
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20200121071702.20150-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Document the driver private data of the BCM2835 auxiliary UART so that
upcoming commits may add further members with proper kerneldoc.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Reviewed-by: Matthias Brugger <mbrugger@suse.com>
Reviewed-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Tested-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Link: https://lore.kernel.org/r/aea363c27fd541dba96d2ebfeee4f596c6d34932.1579175223.git.lukas@wunner.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On probe the bcm2835aux UART driver misreports the register base address
as 0x0:
ttyS0 at MMIO 0x0 (irq = 53, base_baud = 50000000) is a 16550
That's because the driver remaps the registers itself. Take advantage
of the generic remapping code in serial8250_request_std_resource() to
get a message with the correct address and to simplify the driver.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: Martin Sperl <kernel@martin.sperl.org>
Reviewed-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Tested-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Link: https://lore.kernel.org/r/7d1a9bdb05090d8e465fd15cd26d6e81538d07f9.1579175223.git.lukas@wunner.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The bcm2835aux UART driver stores a struct uart_8250_port in its private
data even though it's only passed once to serial8250_register_8250_port()
(which copies all relevant data) and becomes obsolete afterwards.
Allocate the struct on the stack instead for simplicity and to conserve
memory.
The driver also initializes a spinlock in the struct which is never used.
Drop that as well.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: Martin Sperl <kernel@martin.sperl.org>
Reviewed-by: Matthias Brugger <mbrugger@suse.com>
Reviewed-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Tested-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Link: https://lore.kernel.org/r/421d3aed4c34cc8447ac9c26c320961f1b787f11.1579175223.git.lukas@wunner.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Unbinding the bcm2835aux UART driver raises the following error if the
maximum number of 8250 UARTs is set to 1 (via the 8250.nr_uarts module
parameter or CONFIG_SERIAL_8250_RUNTIME_UARTS):
(NULL device *): Removing wrong port: a6f80333 != fa20408b
That's because bcm2835aux_serial_probe() retrieves UART line number 1
from the devicetree and stores it in data->uart.port.line, while
serial8250_register_8250_port() instead uses UART line number 0,
which is stored in data->line.
On driver unbind, bcm2835aux_serial_remove() uses data->uart.port.line,
which contains the wrong number. Fix it.
The issue does not occur if the maximum number of 8250 UARTs is >= 2.
Fixes: bdc5f30095 ("serial: bcm2835: add driver for bcm2835-aux-uart")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: stable@vger.kernel.org # v4.6+
Cc: Martin Sperl <kernel@martin.sperl.org>
Reviewed-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Tested-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Link: https://lore.kernel.org/r/912ccf553c5258135c6d7e8f404a101ef320f0f4.1579175223.git.lukas@wunner.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
QUICC Engine drivers
- Improve the QE drivers to be compatible with ARM/ARM64/PPC64
architectures
- Various cleanups to the QE drivers
-----BEGIN PGP SIGNATURE-----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=e4jk
-----END PGP SIGNATURE-----
Merge tag 'soc-fsl-next-v5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/leo/linux into arm/drivers
NXP/FSL SoC driver updates for v5.6
QUICC Engine drivers
- Improve the QE drivers to be compatible with ARM/ARM64/PPC64
architectures
- Various cleanups to the QE drivers
* tag 'soc-fsl-next-v5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/leo/linux: (49 commits)
soc: fsl: qe: remove set but not used variable 'mm_gc'
soc: fsl: qe: remove PPC32 dependency from CONFIG_QUICC_ENGINE
soc: fsl: qe: remove unused #include of asm/irq.h from ucc.c
net: ethernet: freescale: make UCC_GETH explicitly depend on PPC32
net/wan/fsl_ucc_hdlc: reject muram offsets above 64K
net/wan/fsl_ucc_hdlc: fix reading of __be16 registers
net/wan/fsl_ucc_hdlc: avoid use of IS_ERR_VALUE()
soc: fsl: qe: avoid IS_ERR_VALUE in ucc_fast.c
soc: fsl: qe: drop pointless check in qe_sdma_init()
soc: fsl: qe: drop use of IS_ERR_VALUE in qe_sdma_init()
soc: fsl: qe: avoid IS_ERR_VALUE in ucc_slow.c
soc: fsl: qe: refactor cpm_muram_alloc_common to prevent BUG on error path
soc: fsl: qe: drop broken lazy call of cpm_muram_init()
soc: fsl: qe: make cpm_muram_free() ignore a negative offset
soc: fsl: qe: make cpm_muram_free() return void
soc: fsl: qe: change return type of cpm_muram_alloc() to s32
serial: ucc_uart: access __be32 field using be32_to_cpu
serial: ucc_uart: limit brg-frequency workaround to PPC32
serial: ucc_uart: use of_property_read_u32() in ucc_uart_probe()
serial: ucc_uart: stub out soft_uart_init for !CONFIG_PPC32
...
Link: https://lore.kernel.org/r/1578608351-23289-1-git-send-email-leoyang.li@nxp.com
Signed-off-by: Olof Johansson <olof@lixom.net>
Some of the applications like microcom do not work if
modem is disabled. To fix them we always return
TIOCM_CTS | TIOCM_DSR | TIOCM_CAR instead of 0 when
using cts_override. Make get_mctrl return actual status
when not using cts_override.
Signed-off-by: Maarten Brock <m.brock@vanmierlo.com>
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Link: https://lore.kernel.org/r/1574687731-21563-1-git-send-email-shubhrajyoti.datta@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
During db410c stress test and when the system is low on memory,
the UART/console becomes unresponsive and never recover back.
This has been narrowed down to the msm_start_rx_dma which does
not manage error cases correctly (e.g. dma mapping failure),
indeed, when an error happens, dma transfer is simply discarded
and so never completed, leading to unconfigured RX path.
This patch fixes this issue by switching to SW/FIFO mode in case
of DMA issue. This mainly consists in resetting the receiver to
apply RX BAM/DMA disabling change and re-enabling the RX level
and stale interrupts (previously disabled for DMA transfers).
The DMA will be re-enabled once memory is available since the
SW/FIFO read function (msm_handle_rx_dm) retries to start dma
on completion.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Link: https://lore.kernel.org/r/1578646684-17379-1-git-send-email-loic.poulain@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The 8250 driver can probe for many variants of the venerable 16550A
serial port. Some of those probes involve long (20ms) mdelay calls,
which delay system boot. Modern systems and virtual machines don't have
those variants.
Provide a Kconfig option to disable probes for 16550A variants.
Disabling this speeds up the boot of a virtual machine with a serial
console by more than 20ms (a substantial fraction of the ~100ms needed
to boot a carefully configured VM).
Before:
[ +0.021919] 00:04: ttyS0 at I/O 0x3f8 (irq = 4, base_baud = 115200) is a 16550A
After:
[ +0.000097] 00:04: ttyS0 at I/O 0x3f8 (irq = 4, base_baud = 115200) is a 16550A
Signed-off-by: Josh Triplett <josh@joshtriplett.org>
Link: https://lore.kernel.org/r/20200111022513.GA166267@localhost
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Synchronize only the dirty part of DMA buffer in order to avoid
unnecessary overhead of syncing of the clean part, which is the case
of every serial DMA transfer in practice.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Link: https://lore.kernel.org/r/20200112180919.5194-3-digetx@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This allows DMA engine to go into runtime-suspended mode whenever there is
no data to receive, instead of keeping DMA active all the time while TTY
is opened (i.e. permanently active in practice, like in the case of UART
Bluetooth).
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Link: https://lore.kernel.org/r/20200112180919.5194-2-digetx@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
At this moment, TXEMPTY is checked before sending data on RS485 and ISO7816
modes. However, TXEMPTY is risen when FIFO (if used) or the Transmit Shift
Register are empty, even though TXRDY might be up and controller is able to
receive data. Since the controller sends data only when TXEMPTY is ready,
on RS485, when DMA is not used, the RTS pin is driven low after each byte.
With this patch, the characters will be transmitted when TXRDY is up and
so, RTS pin will remain high between bytes.
The performance improvement on RS485 is about 8% with a baudrate of 300.
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
Acked-by: Richard Genoud <richard.genoud@gmail.com>
Link: https://lore.kernel.org/r/20200107111656.26308-1-codrin.ciubotariu@microchip.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It's not worth to have them in every serial driver and I'm about to add
another helper function.
Signed-off-by: Dmitry Safonov <dima@arista.com>
Link: https://lore.kernel.org/r/20200109215444.95995-2-dima@arista.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The node pointer in question is not a child node, but the node assigned
to the port device itself, so we should not be using
devm_fwnode_get_gpiod_from_child() [that is going away], but standard
devm_gpiod_get().
To maintain the previous labeling we use gpiod_set_consumer_name() after
we acquire the GPIO.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Link: https://lore.kernel.org/r/20200104202314.GA13591@dtor-ws
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In order to support having SERIAL_QCOM_GENI as a module while
also still preserving serial console support, tweak the
Kconfig requirements to not require =y
Cc: Todd Kjos <tkjos@google.com>
Cc: Alistair Delva <adelva@google.com>
Cc: Amit Pundir <amit.pundir@linaro.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: linux-serial@vger.kernel.org
Signed-off-by: John Stultz <john.stultz@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20200107010311.58584-2-john.stultz@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In order to support serial console w/ SERIAL_QCOM_GENI=m,
we need to export the uart_console_device() symbol so things
will build
Cc: Todd Kjos <tkjos@google.com>
Cc: Alistair Delva <adelva@google.com>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Amit Pundir <amit.pundir@linaro.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: linux-serial@vger.kernel.org
Signed-off-by: John Stultz <john.stultz@linaro.org>
Link: https://lore.kernel.org/r/20200107010311.58584-1-john.stultz@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
SGI IOC3 chip has integrated ethernet, keyboard and mouse interface.
It also supports connecting a SuperIO chip for serial and parallel
interfaces. IOC3 is used inside various SGI systemboards and add-on
cards with different equipped external interfaces.
Support for ethernet and serial interfaces were implemented inside
the network driver. This patchset moves out the not network related
parts to a new MFD driver, which takes care of card detection,
setup of platform devices and interrupt distribution for the subdevices.
Serial portion: Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-for-MFD-by: Lee Jones <lee.jones@linaro.org>
Network part: Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Network part: Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Thomas Bogendoerfer <tbogendoerfer@suse.de>
Signed-off-by: Paul Burton <paulburton@kernel.org>
Cc: James Hogan <jhogan@kernel.org>
Cc: David S. Miller <davem@davemloft.net>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: linux-mips@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: netdev@vger.kernel.org
Cc: linux-serial@vger.kernel.org
"earlycon" no need to specify the value string since it uses
stdout-path parameters. However when earlycon and normal console
are not using the same uart port, we need specify value string
to earlycon, this is what we need to do when support dual linux
using jailhouse hypervisor. The 2nd linux will use the uart
of the 1st linux as earlycon.
earlycon=lpuart32,mmio32,0x5a060010,115200 not work for i.MX8QXP.
It is because lpuart32_early_console_setup not support little endian.
Since the original code is to support UPIO_MEM32BE, so if not
UPIO_MEM32, we still take it as UPIO_MEM32BE
Acked-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Link: https://lore.kernel.org/r/1576822230-23125-3-git-send-email-peng.fan@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
EARLYCON_DECLARE is just a wrapper of OF_EARLYCON_DECLARE,
since we already have OF_EARLYCON_DECLARE for lpuart and lpuart32,
so no need EARLYCON_DECLARE.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Link: https://lore.kernel.org/r/1576822230-23125-2-git-send-email-peng.fan@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove code from the driver that create and maintain loopback sysfs node.
Instead use the ioctl TIOCMSET with TIOCM_LOOP argument to set HW to
loopback mode.
Signed-off-by: Akash Asthana <akashast@codeaurora.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/1578321905-25843-3-git-send-email-akashast@codeaurora.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch is the continuation of below mentioned commits which adds wakeup
feature over the UART RX line.
1)commit 3e4aaea7a0 ("tty: serial: qcom_geni_serial: IRQ cleanup")[v2]
2)commit 8b7103f319 ("tty: serial: qcom_geni_serial: Wakeup over UART
RX")[v2]
The following cleanup is done based on upstream comment received on
subsequent versions of the above-mentioned commits to simplifying the code.
- Use devm_kasprintf API in place of scnprintf.
- Use dev_pm_set_dedicated_wake_irq API that will take care of
requesting and attaching wakeup irqs for devices. Also, it sets wakeirq
status to WAKE_IRQ_DEDICATED_ALLOCATED as a result enabling/disabling of
wake irq will be managed by suspend/resume framework. We can remove the
code for enabling and disabling of wake irq from the this driver.
- Use platform_get_irq_optional API to get optional wakeup IRQ for
device.
- Move ISR registration later in probe after uart port gets register with
serial core.
Patch link:
- https://patchwork.kernel.org/patch/11189717/ (v3)
- https://patchwork.kernel.org/patch/11227435/ (v4)
- https://patchwork.kernel.org/patch/11241669/ (v5)
- https://patchwork.kernel.org/patch/11258045/ (v6)
Signed-off-by: Akash Asthana <akashast@codeaurora.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/1578321905-25843-2-git-send-email-akashast@codeaurora.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix up inconsistent usage of upper and lowercase letters in "Exynos"
name.
"EXYNOS" is not an abbreviation but a regular trademarked name.
Therefore it should be written with lowercase letters starting with
capital letter.
The lowercase "Exynos" name is promoted by its manufacturer Samsung
Electronics Co., Ltd., in advertisement materials and on website.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200104152107.11407-18-krzk@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The variable bdp is being initialized with a value that is never
read and it is being updated later with a new value. The initialization
is redundant and can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Timur Tabi <timur@kernel.org>
Link: https://lore.kernel.org/r/20191220001000.39859-1-colin.king@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ioremap has provided non-cached semantics by default since the Linux 2.6
days, so remove the additional ioremap_nocache interface.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Much like the samsung_tty driver (now I know where they copied the idea
from), the 21285 uart driver uses 2 bytes from the "unused" array of
struct uart_port to keep tx/rx enabled/disabled state. Those fields are
going away (they were never really needed in the first place), so fix up
the 21285 driver by another horrible hack.
Instead of creating a whole structure for just 2 bytes, just use two
bits from the private_data pointer instead, as that pointer is never
used. The two bits reflect if tx/rx is now enabled/disabled.
Astute readers will note that once rx is disabled, nothing ever seems to
turn it back on, making one wonder if anyone has ever done this.
Reported-by: kbuild test robot <lkp@intel.com>
Cc: Dmitry Safonov <dima@arista.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: linux-serial@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Link: https://lore.kernel.org/r/20191219145109.GA1962496@kroah.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The SUPPORT_SYSRQ ifdeffery is not nice as:
- May create misunderstanding about sizeof(struct uart_port) between
different objects
- Prevents moving functions from serial_core.h
- Reduces readability (well, it's ifdeffery - it's hard to follow)
In order to remove SUPPORT_SYSRQ, has_sysrq variable has been added.
Initialise it in driver's probe and remove ifdeffery.
Cc: "Maciej W. Rozycki" <macro@linux-mips.org>
Signed-off-by: Dmitry Safonov <dima@arista.com>
Link: https://lore.kernel.org/r/20191213000657.931618-54-dima@arista.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The SUPPORT_SYSRQ ifdeffery is not nice as:
- May create misunderstanding about sizeof(struct uart_port) between
different objects
- Prevents moving functions from serial_core.h
- Reduces readability (well, it's ifdeffery - it's hard to follow)
In order to remove SUPPORT_SYSRQ, has_sysrq variable has been added.
Initialise it in driver's probe and remove ifdeffery.
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Dmitry Safonov <dima@arista.com>
Link: https://lore.kernel.org/r/20191213000657.931618-53-dima@arista.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The SUPPORT_SYSRQ ifdeffery is not nice as:
- May create misunderstanding about sizeof(struct uart_port) between
different objects
- Prevents moving functions from serial_core.h
- Reduces readability (well, it's ifdeffery - it's hard to follow)
In order to remove SUPPORT_SYSRQ, has_sysrq variable has been added.
Initialise it in driver's probe and remove ifdeffery.
Cc: Tony Prisk <linux@prisktech.co.nz>
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Dmitry Safonov <dima@arista.com>
Link: https://lore.kernel.org/r/20191213000657.931618-52-dima@arista.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The SUPPORT_SYSRQ ifdeffery is not nice as:
- May create misunderstanding about sizeof(struct uart_port) between
different objects
- Prevents moving functions from serial_core.h
- Reduces readability (well, it's ifdeffery - it's hard to follow)
In order to remove SUPPORT_SYSRQ, has_sysrq variable has been added.
Initialise it in driver's probe and remove ifdeffery.
Signed-off-by: Dmitry Safonov <dima@arista.com>
Link: https://lore.kernel.org/r/20191213000657.931618-51-dima@arista.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The SUPPORT_SYSRQ ifdeffery is not nice as:
- May create misunderstanding about sizeof(struct uart_port) between
different objects
- Prevents moving functions from serial_core.h
- Reduces readability (well, it's ifdeffery - it's hard to follow)
In order to remove SUPPORT_SYSRQ, has_sysrq variable has been added.
Initialise it in driver's probe and remove ifdeffery.
Cc: "David S. Miller" <davem@davemloft.net>
Cc: sparclinux@vger.kernel.org
Signed-off-by: Dmitry Safonov <dima@arista.com>
Link: https://lore.kernel.org/r/20191213000657.931618-49-dima@arista.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The SUPPORT_SYSRQ ifdeffery is not nice as:
- May create misunderstanding about sizeof(struct uart_port) between
different objects
- Prevents moving functions from serial_core.h
- Reduces readability (well, it's ifdeffery - it's hard to follow)
In order to remove SUPPORT_SYSRQ, has_sysrq variable has been added.
Initialise it in driver's probe and remove ifdeffery.
Signed-off-by: Dmitry Safonov <dima@arista.com>
Link: https://lore.kernel.org/r/20191213000657.931618-38-dima@arista.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The SUPPORT_SYSRQ ifdeffery is not nice as:
- May create misunderstanding about sizeof(struct uart_port) between
different objects
- Prevents moving functions from serial_core.h
- Reduces readability (well, it's ifdeffery - it's hard to follow)
In order to remove SUPPORT_SYSRQ, has_sysrq variable has been added.
Initialise it in driver's probe and remove ifdeffery.
Cc: "David S. Miller" <davem@davemloft.net>
Cc: sparclinux@vger.kernel.org
Signed-off-by: Dmitry Safonov <dima@arista.com>
Link: https://lore.kernel.org/r/20191213000657.931618-48-dima@arista.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The SUPPORT_SYSRQ ifdeffery is not nice as:
- May create misunderstanding about sizeof(struct uart_port) between
different objects
- Prevents moving functions from serial_core.h
- Reduces readability (well, it's ifdeffery - it's hard to follow)
In order to remove SUPPORT_SYSRQ, has_sysrq variable has been added.
Initialise it in driver's probe and remove ifdeffery.
Cc: "David S. Miller" <davem@davemloft.net>
Cc: sparclinux@vger.kernel.org
Signed-off-by: Dmitry Safonov <dima@arista.com>
Link: https://lore.kernel.org/r/20191213000657.931618-47-dima@arista.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The SUPPORT_SYSRQ ifdeffery is not nice as:
- May create misunderstanding about sizeof(struct uart_port) between
different objects
- Prevents moving functions from serial_core.h
- Reduces readability (well, it's ifdeffery - it's hard to follow)
In order to remove SUPPORT_SYSRQ, has_sysrq variable has been added.
Initialise it in driver's probe and remove ifdeffery.
Cc: "David S. Miller" <davem@davemloft.net>
Cc: sparclinux@vger.kernel.org
Signed-off-by: Dmitry Safonov <dima@arista.com>
Link: https://lore.kernel.org/r/20191213000657.931618-46-dima@arista.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The SUPPORT_SYSRQ ifdeffery is not nice as:
- May create misunderstanding about sizeof(struct uart_port) between
different objects
- Prevents moving functions from serial_core.h
- Reduces readability (well, it's ifdeffery - it's hard to follow)
In order to remove SUPPORT_SYSRQ, has_sysrq variable has been added.
Initialise it in driver's probe and remove ifdeffery.
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-stm32@st-md-mailman.stormreply.com
Signed-off-by: Dmitry Safonov <dima@arista.com>
Link: https://lore.kernel.org/r/20191213000657.931618-45-dima@arista.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
