Extend the locking to protect more critical actions like register accesses
in the interrupt handlers.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Only handle an interrupt if at least one combination of event bit
and related interrupt bit is set.
Previously it was just checked that at least one event bit and
at least one interrupt bit are set.
This fixes issues like the following which was caused by
interrupt sharing:
An interrupt intended for nvt_cir_isr was handled by nvt_cir_wake_isr
first and because status bit CIR_WAKE_IRSTS_IR_PENDING was set
the wake fifo was accidently cleared.
This patch also fixes the bug that nvt_cir_wake_isr returned IRQ_HANDLED
even if it detected that the (shared) interrupt was meant for another
handler.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Check for the case that no Nuvoton chip is found on either EFM port.
Also move the position of nvt_efm_disable to reduce the time the
EFM ports are locked.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
At least on Zotac CI321 ACPI provides an ioport range for the wake up part
but accessing these ioports has no effect.
Instead the ioport base address is set to another value already
(0xa20 in my case) and accessing this ioport range works.
Therefore set a new ioport base address only if the current ioport base
address is 0 (register reset default).
The need to use the existing base address instead of trying to set
an own one doesn't seem to be limited to this specific device as other
drivers like hwmon/nct6775 do it the same way.
This change was successfully tested on the mentioned device.
And the change should be generic enough to not break the driver for
other chips (however due to lack of appropriate hardware I wasn't
able to test this).
[mchehab@osg.samsung.com: Tested on Intel NUC NUC5i7RYB with BIOS
version RYBDWi35.86A.0350.2015.0812.1722]
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Tested-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Calling nvt_set_cir_iren separately is not needed as this is done
by nvt_cir_regs_init.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Selecting the logical device in the interrupt handler is not needed
as no configuration register is accessed.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Only enable the logical devices after the registers have been initialized.
The call to nvt_enable_logical_dev in nvt_resume is not needed as this is
done implicitely by nvt_cir_regs_init now.
[mchehab@osg.samsung.com: fixed multiline comment to kernel CodingStyle]
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Switch to using the recently introduced IR default timeout value
(IR_DEFAULT_TIMEOUT) and consider the value of SAMPLE_PERIOD
when calculating the limit count register value.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
At least on NVT6779D clearing the wake fifo works in learning mode only
(although this condition is not mentioned in the chip spec).
Setting the clear fifo bit has no effect in wake up mode.
Even if clearing the wake fifo should work in wake up mode on other
chips this workaround doesn't hurt.
If needed the caller of nvt_clear_cir_wake_fifo has to take care
of locking.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The two EFM ioports are accessed by drivers for other parts of the Nuvoton
Super-IO chips too. Therefore access to these ioports needs to be
protected by using request_muxed_region (like it's implemented e.g. in
hwmon/nct6775 already).
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The FIFO is used for ir_raw_event records, however for some historic
reason the FIFO is used on a per byte basis. IMHO this adds unneeded
complexity. Therefore set up the FIFO for ir_raw_event records.
This also allows to define the FIFO statically as part of
ir_raw_event_ctrl instead of having to allocate the FIFO dynamically.
In addition:
- When writing into the FIFO and it's full return ENOSPC instead of
ENOMEM thus making it easier to tell between "FIFO full" and
"Dynamic memory allocation failed" when the error is propagated to
a higher level.
Also add an error message.
- When reading from the FIFO check whether it's empty.
This is not strictly needed here but kfifo_out is annotated
"must check" anyway.
Successfully tested it with the nuvoton-cir driver.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
When requesting resources use different names for the normal and
the wakeup part. This makes it easier to interpret the output
of e.g. /proc/interrupts and /proc/ioports.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The driver allocates the spinlock but fails to initialize it correctly.
The kernel reports a BUG indicating bad spinlock magic when spinlock
debugging is enabled.
Call spin_lock_init() on it to initialize it correctly.
Fixes: b4e3e59fb5 ("[media] rc: add sunxi-ir driver")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Now that that the decoder modules are loaded on-demand we can move
loading the lirc module to rc_register_device directly and remove
unneeded functions and comments.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Checking whether a protocol is enabled and calling the related decoder
functions should be done by the rc core, not the protocol handlers.
Properly handle lirc considering that no protocol bit is set for lirc.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Declare struct proto_names and its member name as const.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Prepare on-demand decoder module loading by adding a module_name member
to struct proto_names and introducing the related load function.
After this patch of the series the decoder modules are still loaded
unconditionally.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Currently, if a decoder module is unloadad, the respective protocol
is still shown as enabled (if it was enabled before).
Fix this by resetting the respective protocol bits if a decoder
module is unloaded.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Simplify the logging.
I had some doubts about using the elvis operator as it's GNU extension.
However GNU extensions are explicitely allowed and this operator is
used at several places in the kernel code.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Switch the info about the detected chip type from debug to info level
as it might be useful not only for debugging purposes.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Instead of explicitely checking debug use nvt_dbg like in other parts
of the driver thus simplifying the code.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add support for the NCT6779D. It's found e.g. on the Zotac CI321 mini-pc
and I successfully tested it on this device.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Make the chip detection code more similar to the one used for the
same chips in watchdog/w83627hf_wdt.c and hwmon/w83627ehf.c.
Apart from better maintainability we gain
- unified naming of chips (e.g. 677C -> NCT6776F)
- driver works with all revisions of the chips
(least 4 bits of id are masked)
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Using IRQ_RETVAL is unneeded here. IRQ_NONE / IRQ_HANDLED can be
returned directly.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Denon also uses the Sharp protocol, however with different check bits.
It would have been also possible to add this as a separate protocol
but this may not be worth the effort.
Successfully tested with a Denon RC-1002 remote control.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
streamzap uses 'struct timeval' to store the start time of a signal for
gap tracking. struct timeval uses a 32-bit seconds representation which
will overflow in year 2038 and beyond. Replace struct timeval with ktime_t
which uses a 64-bit seconds representation and is 2038 safe. This patch
uses ktime_get_real() preserving the use of wall-clock time in the
original code.
Signed-off-by: Tina Ruchandani <ruchandani.tina@gmail.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
rc-main mistakenly uses #ifdef MODULE to determine whether it should
load the rc keymap modules. This symbol is only defined if rc-main
is being built as a module itself, and bears no relation to whether
the rc keymaps are modules.
Fix this to use CONFIG_MODULES instead.
Fixes: 631493ecac ("[media] rc-core: merge rc-map.c into rc-main.c")
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Many decoders require a trailing space (period without IR illumination)
to be delivered before completing a decode.
Since the gpio-ir-recv driver only delivers events on gpio transitions,
a single IR symbol (caused by a quick touch on an IR remote) will not
be properly decoded without the use of a timer to flush the tail end
state of the IR receiver.
This patch initializes and uses a timer and the timeout field of rcdev
to complete the stream and allow decode.
The timeout can be overridden through the use of the LIRC_SET_REC_TIMEOUT
ioctl.
Signed-off-by: Eric Nelson <eric@nelint.com>
Acked-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The device is set as wakeup capable using proper wakeup API but the
driver misuses IRQF_NO_SUSPEND to set the interrupt as wakeup source
which is incorrect.
This patch removes the use of IRQF_NO_SUSPEND flags replacing it with
enable_irq_wake instead.
Cc: Srinivas Kandagatla <srinivas.kandagatla@gmail.com>
Cc: Maxime Coquelin <maxime.coquelin@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: kernel@stlinux.com
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Let's not mix platform_data headers with the core headers. Instead, let's
create a subdir at linux/platform_data and move the headers to that
common place, adding it to MAINTAINERS.
The headers were moved with:
mkdir include/linux/platform_data/media/; git mv include/media/gpio-ir-recv.h include/media/ir-rx51.h include/media/mmp-camera.h include/media/omap1_camera.h include/media/omap4iss.h include/media/s5p_hdmi.h include/media/si4713.h include/media/sii9234.h include/media/smiapp.h include/media/soc_camera.h include/media/soc_camera_platform.h include/media/timb_radio.h include/media/timb_video.h include/linux/platform_data/media/
And the references fixed with this script:
MAIN_DIR="linux/platform_data/"
PREV_DIR="media/"
DIRS="media/"
echo "Checking affected files" >&2
for i in $DIRS; do
for j in $(find include/$MAIN_DIR/$i -type f -name '*.h'); do
n=`basename $j`
git grep -l $n
done
done|sort|uniq >files && (
echo "Handling files..." >&2;
echo "for i in \$(cat files|grep -v Documentation); do cat \$i | \\";
(
cd include/$MAIN_DIR;
for j in $DIRS; do
for i in $(ls $j); do
echo "perl -ne 's,(include [\\\"\\<])$PREV_DIR($i)([\\\"\\>]),\1$MAIN_DIR$j\2\3,; print \$_' |\\";
done;
done;
echo "cat > a && mv a \$i; done";
);
echo "Handling documentation..." >&2;
echo "for i in MAINTAINERS \$(cat files); do cat \$i | \\";
(
cd include/$MAIN_DIR;
for j in $DIRS; do
for i in $(ls $j); do
echo " perl -ne 's,include/$PREV_DIR($i)\b,include/$MAIN_DIR$j\1,; print \$_' |\\";
done;
done;
echo "cat > a && mv a \$i; done"
);
) >script && . ./script
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
This driver doesn't claim the IR transmitter to be wakeup source. It
even disables the clock and the IR during suspend-resume cycle.
This patch removes yet another misuse of IRQF_NO_SUSPEND.
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Guoxiong Yan <yanguoxiong@huawei.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Acked-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=cIed
-----END PGP SIGNATURE-----
Merge tag 'media/v4.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
- new DVB frontend drivers: ascot2e, cxd2841er, horus3a, lnbh25
- new HDMI capture driver: tc358743
- new driver for NetUP DVB new boards (netup_unidvb)
- IR support for DVBSky cards (smipcie-ir)
- Coda driver has gain macroblock tiling support
- Renesas R-Car gains JPEG codec driver
- new DVB platform driver for STi boards: c8sectpfe
- added documentation for the media core kABI to device-drivers DocBook
- lots of driver fixups, cleanups and improvements
* tag 'media/v4.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (297 commits)
[media] c8sectpfe: Remove select on undefined LIBELF_32
[media] i2c: fix platform_no_drv_owner.cocci warnings
[media] cx231xx: Use wake_up_interruptible() instead of wake_up_interruptible_nr()
[media] tc358743: only queue subdev notifications if devnode is set
[media] tc358743: add missing Kconfig dependency/select
[media] c8sectpfe: Use %pad to print 'dma_addr_t'
[media] DocBook media: Fix typo "the the" in xml files
[media] tc358743: make reset gpio optional
[media] tc358743: set direction of reset gpio using devm_gpiod_get
[media] dvbdev: document most of the functions/data structs
[media] dvb_frontend.h: document the struct dvb_frontend
[media] dvb-frontend.h: document struct dtv_frontend_properties
[media] dvb-frontend.h: document struct dvb_frontend_ops
[media] dvb: Use DVBFE_ALGO_HW where applicable
[media] dvb_frontend.h: document struct analog_demod_ops
[media] dvb_frontend.h: Document struct dvb_tuner_ops
[media] Docbook: Document struct analog_parameters
[media] dvb_frontend.h: get rid of dvbfe_modcod
[media] add documentation for struct dvb_tuner_info
[media] dvb_frontend: document dvb_frontend_tune_settings
...
This reverts commit 9869da5bac.
The current code is not mature enough, the API should allow a single
protocol to be specified. Also, the current code contains heuristics
that will depend on module load order.
Signed-off-by: David Härdeman <david@hardeman.nu>
Acked-by: Antti Seppälä <a.seppala@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This reverts commit 1d971d927e.
The current code is not mature enough, the API should allow a single
protocol to be specified. Also, the current code contains heuristics
that will depend on module load order.
Signed-off-by: David Härdeman <david@hardeman.nu>
Acked-by: Antti Seppälä <a.seppala@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This reverts commit a0466f15b4.
The current code is not mature enough, the API should allow a single
protocol to be specified. Also, the current code contains heuristics
that will depend on module load order.
Signed-off-by: David Härdeman <david@hardeman.nu>
Acked-by: Antti Seppälä <a.seppala@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This reverts commit cf257e288a.
The current code is not mature enough, the API should allow a single
protocol to be specified. Also, the current code contains heuristics
that will depend on module load order.
Signed-off-by: David Härdeman <david@hardeman.nu>
Acked-by: Antti Seppälä <a.seppala@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This reverts commit 0d830b2d12.
The current code is not mature enough, the API should allow a single
protocol to be specified. Also, the current code contains heuristics
that will depend on module load order.
Signed-off-by: David Härdeman <david@hardeman.nu>
Acked-by: Antti Seppälä <a.seppala@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This reverts commit 2e4ebde269.
The current code is not mature enough, the API should allow a single
protocol to be specified. Also, the current code contains heuristics
that will depend on module load order.
Signed-off-by: David Härdeman <david@hardeman.nu>
Acked-by: Antti Seppälä <a.seppala@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
