The vzalloc_node(), already rounds the total size to whole pages, and
sizeof(u64) is smaller than sizeof(struct recv_comp_data). So
round_up of recv_completion_cnt is not necessary, and may cause extra
memory allocation.
To save memory, remove this unnecessary round_up for recv_completion_cnt.
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement support for setting of packet trap group parameters by
invoking the trap_group_init() callback with the new parameters.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some packet traps are currently exposed to user space as being member of
"l3_drops" trap group, but internally they are member of a different
group.
Switch these traps to use the correct group so that they are all subject
to the same policer, as exposed to user space.
Set the trap priority of packets trapped due to loopback error during
routing to the lowest priority. Such packets are not routed again by the
kernel and therefore should not mask other traps (e.g., host miss) that
should be routed.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The policer is now initialized as part of the registration with devlink,
so there is no need to initialize it before the registration.
Remove the initialization.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Register supported packet trap policers with devlink and implement
callbacks to change their parameters and read their counters.
Prevent user space from passing invalid policer parameters down to the
device by checking their validity and communicating the failure via an
appropriate extack message.
v2:
* Remove the max/min validity checks from __mlxsw_sp_trap_policer_set()
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prepare an array of policer IDs to register with devlink and their
associated parameters.
The array is composed from both policers that are currently bound to
exposed trap groups and policers that are not bound to any trap group.
v2:
* Provide max/min rate/burst size when registering policers
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During initialization the driver configures various packet trap groups
and binds policers to them.
Currently, most of these groups are not exposed to user space and
therefore their policers should not be exposed as well. Otherwise, user
space will be able to alter policer parameters without knowing which
packet traps are policed by the policer.
Use a bitmap to track the used policer IDs so that these policers will
not be registered with devlink in a subsequent patch.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The QoS Policer Configuration Register (QPCR) is used to configure
hardware policers. Extend this register with following fields and
defines which will be used by subsequent patches:
1. Violate counter: reads number of packets dropped by the policer
2. Clear counter: to ensure we start counting from 0
3. Rate and burst size limits
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a dummy callback to set trap group parameters. Return an error when
the 'fail_trap_group_set' debugfs file is set in order to exercise error
paths and verify that error is propagated to user space when should.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Packet trap groups are used to aggregate logically related packet traps.
Currently, these groups allow user space to batch operations such as
setting the trap action of all member traps.
In order to prevent the CPU from being overwhelmed by too many trapped
packets, it is desirable to bind a packet trap policer to these groups.
For example, to limit all the packets that encountered an exception
during routing to 10Kpps.
Allow device drivers to bind default packet trap policers to packet trap
groups when the latter are registered with devlink.
The next patch will enable user space to change this default binding.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Register three dummy packet trap policers with devlink and implement
callbacks to change their parameters and read their counters.
This will be used later on in the series to test the devlink-trap
policer infrastructure.
v2:
* Remove check about burst size being a power of 2 and instead add a
debugfs knob to fail the operation
* Provide max/min rate/burst size when registering policers and remove
the validity checks from nsim_dev_devlink_trap_policer_set()
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull locking updates from Ingo Molnar:
"The main changes in this cycle were:
- Continued user-access cleanups in the futex code.
- percpu-rwsem rewrite that uses its own waitqueue and atomic_t
instead of an embedded rwsem. This addresses a couple of
weaknesses, but the primary motivation was complications on the -rt
kernel.
- Introduce raw lock nesting detection on lockdep
(CONFIG_PROVE_RAW_LOCK_NESTING=y), document the raw_lock vs. normal
lock differences. This too originates from -rt.
- Reuse lockdep zapped chain_hlocks entries, to conserve RAM
footprint on distro-ish kernels running into the "BUG:
MAX_LOCKDEP_CHAIN_HLOCKS too low!" depletion of the lockdep
chain-entries pool.
- Misc cleanups, smaller fixes and enhancements - see the changelog
for details"
* 'locking-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (55 commits)
fs/buffer: Make BH_Uptodate_Lock bit_spin_lock a regular spinlock_t
thermal/x86_pkg_temp: Make pkg_temp_lock a raw_spinlock_t
Documentation/locking/locktypes: Minor copy editor fixes
Documentation/locking/locktypes: Further clarifications and wordsmithing
m68knommu: Remove mm.h include from uaccess_no.h
x86: get rid of user_atomic_cmpxchg_inatomic()
generic arch_futex_atomic_op_inuser() doesn't need access_ok()
x86: don't reload after cmpxchg in unsafe_atomic_op2() loop
x86: convert arch_futex_atomic_op_inuser() to user_access_begin/user_access_end()
objtool: whitelist __sanitizer_cov_trace_switch()
[parisc, s390, sparc64] no need for access_ok() in futex handling
sh: no need of access_ok() in arch_futex_atomic_op_inuser()
futex: arch_futex_atomic_op_inuser() calling conventions change
completion: Use lockdep_assert_RT_in_threaded_ctx() in complete_all()
lockdep: Add posixtimer context tracing bits
lockdep: Annotate irq_work
lockdep: Add hrtimer context tracing bits
lockdep: Introduce wait-type checks
completion: Use simple wait queues
sched/swait: Prepare usage in completions
...
- Clean up and rework the PM QoS API to simplify the code and
reduce the size of it (Rafael Wysocki).
- Fix a suspend-to-idle wakeup regression on Dell XPS13 9370
and similar platforms where the USB plug/unplug events are
handled by the EC (Rafael Wysocki).
- CLean up the intel_idle and PSCI cpuidle drivers (Rafael Wysocki,
Ulf Hansson).
- Extend the haltpoll cpuidle driver so that it can be forced to
run on some systems where it refused to load (Maciej Szmigiero).
- Convert several cpufreq documents to the .rst format and move the
legacy driver documentation into one common file (Mauro Carvalho
Chehab, Rafael Wysocki).
- Update several cpufreq drivers:
* Extend and fix the imx-cpufreq-dt driver (Anson Huang).
* Improve the -EPROBE_DEFER handling and fix unwanted CPU
overclocking on i.MX6ULL in imx6q-cpufreq (Anson Huang,
Christoph Niedermaier).
* Add support for Krait based SoCs to the qcom driver (Ansuel
Smith).
* Add support for OPP_PLUS to ti-cpufreq (Lokesh Vutla).
* Add platform specific intermediate callbacks support to
cpufreq-dt and update the imx6q driver (Peng Fan).
* Simplify and consolidate some pieces of the intel_pstate driver
and update its documentation (Rafael Wysocki, Alex Hung).
- Fix several devfreq issues:
* Remove unneeded extern keyword from a devfreq header file
and use the DEVFREQ_GOV_UPDATE_INTERNAL event name instead of
DEVFREQ_GOV_INTERNAL (Chanwoo Choi).
* Fix the handling of dev_pm_qos_remove_request() result (Leonard
Crestez).
* Use constant name for userspace governor (Pierre Kuo).
* Get rid of doc warnings and fix a typo (Christophe JAILLET).
- Use built-in RCU list checking in some places in the PM core to
avoid false-positive RCU usage warnings (Madhuparna Bhowmik).
- Add explicit READ_ONCE()/WRITE_ONCE() annotations to low-level
PM QoS routines (Qian Cai).
- Fix removal of wakeup sources to avoid NULL pointer dereferences
in a corner case (Neeraj Upadhyay).
- Clean up the handling of hibernate compat ioctls and fix the
related documentation (Eric Biggers).
- Update the idle_inject power capping driver to use variable-length
arrays instead of zero-length arrays (Gustavo Silva).
- Fix list format in a PM QoS document (Randy Dunlap).
- Make the cpufreq stats module use scnprintf() to avoid potential
buffer overflows (Takashi Iwai).
- Add pm_runtime_get_if_active() to PM-runtime API (Sakari Ailus).
- Allow no domain-idle-states DT property in generic PM domains (Ulf
Hansson).
- Fix a broken y-axis scale in the intel_pstate_tracer utility (Doug
Smythies).
-----BEGIN PGP SIGNATURE-----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=cBQd
-----END PGP SIGNATURE-----
Merge tag 'pm-5.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management updates from Rafael Wysocki:
"These clean up and rework the PM QoS API, address a suspend-to-idle
wakeup regression on some ACPI-based platforms, clean up and extend a
few cpuidle drivers, update multiple cpufreq drivers and cpufreq
documentation, and fix a number of issues in devfreq and several other
things all over.
Specifics:
- Clean up and rework the PM QoS API to simplify the code and reduce
the size of it (Rafael Wysocki).
- Fix a suspend-to-idle wakeup regression on Dell XPS13 9370 and
similar platforms where the USB plug/unplug events are handled by
the EC (Rafael Wysocki).
- CLean up the intel_idle and PSCI cpuidle drivers (Rafael Wysocki,
Ulf Hansson).
- Extend the haltpoll cpuidle driver so that it can be forced to run
on some systems where it refused to load (Maciej Szmigiero).
- Convert several cpufreq documents to the .rst format and move the
legacy driver documentation into one common file (Mauro Carvalho
Chehab, Rafael Wysocki).
- Update several cpufreq drivers:
* Extend and fix the imx-cpufreq-dt driver (Anson Huang).
* Improve the -EPROBE_DEFER handling and fix unwanted CPU
overclocking on i.MX6ULL in imx6q-cpufreq (Anson Huang,
Christoph Niedermaier).
* Add support for Krait based SoCs to the qcom driver (Ansuel
Smith).
* Add support for OPP_PLUS to ti-cpufreq (Lokesh Vutla).
* Add platform specific intermediate callbacks support to
cpufreq-dt and update the imx6q driver (Peng Fan).
* Simplify and consolidate some pieces of the intel_pstate
driver and update its documentation (Rafael Wysocki, Alex
Hung).
- Fix several devfreq issues:
* Remove unneeded extern keyword from a devfreq header file and
use the DEVFREQ_GOV_UPDATE_INTERNAL event name instead of
DEVFREQ_GOV_INTERNAL (Chanwoo Choi).
* Fix the handling of dev_pm_qos_remove_request() result
(Leonard Crestez).
* Use constant name for userspace governor (Pierre Kuo).
* Get rid of doc warnings and fix a typo (Christophe JAILLET).
- Use built-in RCU list checking in some places in the PM core to
avoid false-positive RCU usage warnings (Madhuparna Bhowmik).
- Add explicit READ_ONCE()/WRITE_ONCE() annotations to low-level PM
QoS routines (Qian Cai).
- Fix removal of wakeup sources to avoid NULL pointer dereferences in
a corner case (Neeraj Upadhyay).
- Clean up the handling of hibernate compat ioctls and fix the
related documentation (Eric Biggers).
- Update the idle_inject power capping driver to use variable-length
arrays instead of zero-length arrays (Gustavo Silva).
- Fix list format in a PM QoS document (Randy Dunlap).
- Make the cpufreq stats module use scnprintf() to avoid potential
buffer overflows (Takashi Iwai).
- Add pm_runtime_get_if_active() to PM-runtime API (Sakari Ailus).
- Allow no domain-idle-states DT property in generic PM domains (Ulf
Hansson).
- Fix a broken y-axis scale in the intel_pstate_tracer utility (Doug
Smythies)"
* tag 'pm-5.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (78 commits)
cpufreq: intel_pstate: Simplify intel_pstate_cpu_init()
tools/power/x86/intel_pstate_tracer: fix a broken y-axis scale
ACPI: PM: s2idle: Refine active GPEs check
ACPICA: Allow acpi_any_gpe_status_set() to skip one GPE
PM: sleep: wakeup: Skip wakeup_source_sysfs_remove() if device is not there
PM / devfreq: Get rid of some doc warnings
PM / devfreq: Fix handling dev_pm_qos_remove_request result
PM / devfreq: Fix a typo in a comment
PM / devfreq: Change to DEVFREQ_GOV_UPDATE_INTERVAL event name
PM / devfreq: Remove unneeded extern keyword
PM / devfreq: Use constant name of userspace governor
ACPI: PM: s2idle: Fix comment in acpi_s2idle_prepare_late()
cpufreq: qcom: Add support for krait based socs
cpufreq: imx6q-cpufreq: Improve the logic of -EPROBE_DEFER handling
cpufreq: Use scnprintf() for avoiding potential buffer overflow
cpuidle: psci: Split psci_dt_cpu_init_idle()
PM / Domains: Allow no domain-idle-states DT property in genpd when parsing
PM / hibernate: Remove unnecessary compat ioctl overrides
PM: hibernate: fix docs for ioctls that return loff_t via pointer
Documentation: intel_pstate: update links for references
...
Add a separate set of PCS operations, which MAC drivers can use to
couple phylink with their associated MAC PCS layer. The PCS
operations include:
- pcs_get_state() - reads the link up/down, resolved speed, duplex
and pause from the PCS.
- pcs_config() - configures the PCS for the specified mode, PHY
interface type, and setting the advertisement.
- pcs_an_restart() - restarts 802.3 in-band negotiation with the
link partner
- pcs_link_up() - informs the PCS that link has come up, and the
parameters of the link. Link parameters are used to program the
PCS for fixed speed and non-inband modes.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename the bland 'ops' member of struct phylink to be a more
descriptive 'mac_ops' - this is necessary as we're about to introduce
another set of operations.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change phylink_mii_c22_pcs_set_advertisement() to take only the PHY
interface and advertisement mask, rather than the full phylink state.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Factor out mapping the tx skb to a new function rtl8169_tx_map(). This
allows to remove redundancies, and rtl8169_get_txd_opts1() has only
one user left, so it can be inlined.
As a result rtl8169_xmit_frags() is significantly simplified, and in
rtl8169_start_xmit() the code is simplified and better readable.
No functional change intended.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The qed_chain data structure was modified in
commit 1a4a69751f ("qed: Chain support for external PBL") to support
receiving an external pbl (due to iWARP FW requirements).
The pages pointed to by the pbl are allocated in qed_chain_alloc
and their virtual address are stored in an virtual addresses array to
enable accessing and freeing the data. The physical addresses however
weren't stored and were accessed directly from the external-pbl
during free.
Destroy-qp flow, leads to freeing the external pbl before the chain is
freed, when the chain is freed it tries accessing the already freed
external pbl, leading to a use-after-free. Therefore we need to store
the physical addresses in additional to the virtual addresses in a
new data structure.
Fixes: 1a4a69751f ("qed: Chain support for external PBL")
Signed-off-by: Michal Kalderon <mkalderon@marvell.com>
Signed-off-by: Yuval Bason <ybason@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the mtu is greater than TD_MSS_MAX, then TSO is disabled, see
rtl8169_fix_features(). Because mss is less than mtu, we can't have
the case mss > TD_MSS_MAX in the TSO path.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds complete support for manipulating the L2 Policing Tables
from this switch. There are 45 table entries, one entry per each port
and traffic class, and one dedicated entry for broadcast traffic for
each ingress port.
Policing entries are shareable, and we use this functionality to support
shared block filters.
We are modeling broadcast policers as simple tc-flower matches on
dst_mac. As for the traffic class policers, the switch only deduces the
traffic class from the VLAN PCP field, so it makes sense to model this
as a tc-flower match on vlan_prio.
How to limit broadcast traffic coming from all front-panel ports to a
cumulated total of 10 Mbit/s:
tc qdisc add dev sw0p0 ingress_block 1 clsact
tc qdisc add dev sw0p1 ingress_block 1 clsact
tc qdisc add dev sw0p2 ingress_block 1 clsact
tc qdisc add dev sw0p3 ingress_block 1 clsact
tc filter add block 1 flower skip_sw dst_mac ff:ff:ff:ff:ff:ff \
action police rate 10mbit burst 64k
How to limit traffic with VLAN PCP 0 (also includes untagged traffic) to
100 Mbit/s on port 0 only:
tc filter add dev sw0p0 ingress protocol 802.1Q flower skip_sw \
vlan_prio 0 action police rate 100mbit burst 64k
The broadcast, VLAN PCP and port policers are compatible with one
another (can be installed at the same time on a port).
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds partial configuration support for the L2 Policing Table. Out
of the 45 policing entries, only 5 are used (one for each port), in a
shared manner. All 8 traffic classes, and the broadcast policer, are
redirected to a common instance which belongs to the ingress port.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is a trivial passthrough towards the ocelot library, which
support port policers since commit 2c1d029a01 ("net: mscc: ocelot:
Implement port policers via tc command").
Some data structure conversion between the DSA core and the Ocelot
library is necessary, for policer parameters.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ocelot has 384 policers that can be allocated to ingress ports,
QoS classes per port, and VCAP IS2 entries. ocelot_police.c
supports to set policers which can be allocated to police action
of VCAP IS2. We allocate policers from maximum pol_id, and
decrease the pol_id when add a new vcap_is2 entry which is
police action.
Signed-off-by: Xiaoliang Yang <xiaoliang.yang_1@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the FW RESET event comes to the driver from the firmware,
or the fw_status goes to 0 (stopped) or to 0xff (no PCI
connection), then shut down the driver activity. This event
signals a FW upgrade where we need to quiesce all operations and
wait for the FW to restart. The FW will continue the update
process once it sees all the LIFs are reset. When the update
process is done it will set the fw_status back to RUNNING.
Meanwhile, the heartbeat check continues and when the fw_status
is seen as set to running we can restart the driver operations.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the link goes down, we need to disable the queues on the
NIC in addition to stopping the netdev stack. This lets the
FW know that the driver has stopped queue activity, and then
the FW can do internal reconfiguration work, whether actually
Link related, or for other internal FW needs. To do this,
we pull out the queue enable and disable from ionic_open()
and ionic_stop() so they can be used by other routines.
To help keep things sane, we swap the queue enables so that
the rx queue and its napi are enabled before the tx queue
which rides on the rx queues napi.
We also drop the ionic_lif_quiesce() as it doesn't do anything
more than what the queue disable has already taken care of.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure the queue structures exist before trying
to delete them. This addresses a couple of error
recovery issues.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clean out tx requests that didn't get finished before
shutting down the queue.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the irq request and free out of the qcq_init and deinit
and into the alloc and free routines where they belong for
better resource management.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the qcq debugfs add to the queue alloc, and likewise move
the debugfs delete to the queue free. The LIF debugfs add
also needs to be moved, but the del is already in the LIF free.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a link_status_check to the heartbeat watchdog.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rearrange the link_up/link_down messages so that we announce
link up when we first notice that the link is up when the
driver loads, and decouple the link_up/link_down messages from
the UP and DOWN netdev state.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cited commit extended the enums 'hwtstamp_tx_types' and
'hwtstamp_rx_filters' with values that were not accounted for in the
switch statements, resulting in the build warnings below.
Fix by adding a default case.
drivers/net/ethernet/mellanox/mlxsw/spectrum_ptp.c: In function ‘mlxsw_sp_ptp_get_message_types’:
drivers/net/ethernet/mellanox/mlxsw/spectrum_ptp.c:915:2: warning: enumeration value ‘__HWTSTAMP_TX_CNT’ not handled in switch [-Wswitch]
915 | switch (tx_type) {
| ^~~~~~
drivers/net/ethernet/mellanox/mlxsw/spectrum_ptp.c:927:2: warning: enumeration value ‘__HWTSTAMP_FILTER_CNT’ not handled in switch [-Wswitch]
927 | switch (rx_filter) {
| ^~~~~~
Fixes: f76510b458 ("ethtool: add timestamping related string sets")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reported-by: David S. Miller <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
When health reporter is registered to devlink, devlink will implicitly set
auto recover if and only if the reporter has a recover method. No reason
to explicitly get the auto recover flag from the driver.
Remove this flag from all drivers that called
devlink_health_reporter_create.
All existing health reporters set auto recovery to true if they have a
recover method.
Yet, administrator can unset auto recover via netlink command as prior to
this patch.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Health reporters should be registered with auto recover set to true.
Align dummy reporter behaviour with that, as in later patch the option to
set auto recover behaviour will be removed.
In addition, align netdevsim selftest to the new default value.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PTP Hardware Clock (PHC) subsystem offers an API for configuring
programmable pins. User space sets or gets the settings using ioctls,
and drivers verify dialed settings via a callback. Drivers may also
query pin settings by calling the ptp_find_pin() method.
Although the core subsystem protects concurrent access to the pin
settings, the implementation places illogical restrictions on how
drivers may call ptp_find_pin(). When enabling an auxiliary function
via the .enable(on=1) callback, drivers may invoke the pin finding
method, but when disabling with .enable(on=0) drivers are not
permitted to do so. With the exception of the mv88e6xxx, all of the
PHC drivers do respect this restriction, but still the locking pattern
is both confusing and unnecessary.
This patch changes the locking implementation to allow PHC drivers to
freely call ptp_find_pin() from their .enable() and .verify()
callbacks.
V2 ChangeLog:
- fixed spelling in the kernel doc
- add Vladimir's tested by tag
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Reported-by: Yangbo Lu <yangbo.lu@nxp.com>
Tested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It may be up to the driver (in case ANY HW stats is passed) to select
which type of HW stats he is going to use. Add an infrastructure to
expose this information to user.
$ tc filter add dev enp3s0np1 ingress proto ip handle 1 pref 1 flower dst_ip 192.168.1.1 action drop
$ tc -s filter show dev enp3s0np1 ingress
filter protocol ip pref 1 flower chain 0
filter protocol ip pref 1 flower chain 0 handle 0x1
eth_type ipv4
dst_ip 192.168.1.1
in_hw in_hw_count 2
action order 1: gact action drop
random type none pass val 0
index 1 ref 1 bind 1 installed 10 sec used 10 sec
Action statistics:
Sent 0 bytes 0 pkt (dropped 0, overlimits 0 requeues 0)
backlog 0b 0p requeues 0
used_hw_stats immediate <<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When device is not open, the service task which update the port
information per second is not running. In this case, the port
capabilities, including speed ability, autoneg ability, media type,
may be incorrect. Then get/set link ksetting may fail.
This patch fixes it by updating the port information before getting/
setting link ksettings when device is not open, and start timer
task immediately by setting delay time to 0 when device opens.
Fixes: 46a3df9f97 ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support")
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, VF's RSS configuration would be set to default
after VF reset, the the user's one will loss.
To fix it, this patch separates hclgevf_rss_init_hw() into
two parts, one sets up the default RSS configuration and
just be called when driver loading, one configures the hardware
and be called by driver loading or reset.
Fixes: d97b307213 ("net: hns3: Add RSS tuples support for VF")
Signed-off-by: Guojia Liao <liaoguojia@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the fraglist SKB headlen is larger than zero, current code
still handle the fraglist SKB linear data as frag data, which may
cause TX error.
This patch adds a new DESC_TYPE_FRAGLIST_SKB type to handle the
mapping and unmapping of the fraglist SKB linear data buffer.
Fixes: 8ae10cfb50 ("net: hns3: support tx-scatter-gather-fraglist feature")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix sparse warnings:
drivers/net/ethernet/amazon/ena/ena_netdev.c:460:6: warning: symbol 'ena_xdp_exchange_program_rx_in_range' was not declared. Should it be static?
drivers/net/ethernet/amazon/ena/ena_netdev.c:481:6: warning: symbol 'ena_xdp_exchange_program' was not declared. Should it be static?
drivers/net/ethernet/amazon/ena/ena_netdev.c:1555:5: warning: symbol 'ena_xdp_handle_buff' was not declared. Should it be static?
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix sparse warning:
drivers/net/ethernet/freescale/dpaa/dpaa_eth.c:2065:5:
warning: symbol 'dpaa_a050385_wa' was not declared. Should it be static?
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for VLAN ID-based filtering by the MAC controller for MAC
drivers that support it. Only the 12-bit VID field is used.
Signed-off-by: Chuah Kim Tatt <kim.tatt.chuah@intel.com>
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: Wong Vee Khee <vee.khee.wong@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a spelling mistake in a dev_err error message. Fix it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add mlx5e_rep_indr_setup_ft_cb to support indr block setup
in FT mode.
Both tc rules and flow table rules are of the same format,
It can re-use tc parsing for that, and move the flow table rules
to their steering domain(the specific chain_index), the indr
block offload in FT also follow this scenario.
Signed-off-by: wenxu <wenxu@ucloud.cn>
Reviewed-by: Vlad Buslov <vladbu@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Refactor indr setup block for support ft indr setup in the
next patch. The function mlx5e_rep_indr_offload exposes
'flags' in order set additional flag for FT in next patch.
Rename mlx5e_rep_indr_setup_tc_block to mlx5e_rep_indr_setup_block
and add flow_setup_cb_t callback parameters in order set the
specific callback for FT in next patch.
Signed-off-by: wenxu <wenxu@ucloud.cn>
Reviewed-by: Vlad Buslov <vladbu@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
eswitch_offloads_chains.{c,h} were just introduced this kernel release
cycle, eswitch is in high development demand right now and many
features are planned to be added to it. eswitch deserves its own
directory and here we move these new files to there, in preparation for
upcoming eswitch features and new files.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
In VF lag mode when remove the bonding module without bring down the
bond device first, we could potentially have circular dependency when we
unload IB devices and also handle fib events:
1. The bond work starts first;
2. The "modprobe -rv bonding" process tries to release the bond device,
with the "pernet_ops_rwsem" lock hold;
3. The bond work blocks in unregister_netdevice_notifier() and waits for
the lock because fib event came right before;
4. The kernel fib module tries to free all the fib entries by broadcasting
the "FIB_EVENT_NH_DEL" event;
5. Upon the fib event this lag_mp module holds the fib lock and queue a
fib work.
So:
bond work -> modprobe task -> kernel fib module -> lag_mp -> bond work
Today we either reload IB devices in roce lag in nic mode or either handle
fib events in switchdev mode, but a new feature could change that we'll
need to reload IB devices also in switchdev mode so this is a future proof
fix as one may not notice this later.
Signed-off-by: Mark Zhang <markz@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
* 'mlx5-next' of git://git.kernel.org/pub/scm/linux/kernel/git/mellanox/linux:
mlx5: Remove uninitialized use of key in mlx5_core_create_mkey
{IB,net}/mlx5: Move asynchronous mkey creation to mlx5_ib
{IB,net}/mlx5: Assign mkey variant in mlx5_ib only
{IB,net}/mlx5: Setup mkey variant before mr create command invocation
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
A recent commit e893768179 ("devlink: prepare to support region
operations") used the region_cr_space_str and region_fw_health_str
variables as initializers for the devlink_region_ops structures.
This can result in compiler errors:
drivers/net/ethernet/mellanox//mlx4/crdump.c:45:10: error: initializer
element is not constant
.name = region_cr_space_str,
^
drivers/net/ethernet/mellanox//mlx4/crdump.c:45:10: note: (near
initialization for ‘region_cr_space_ops.name’)
drivers/net/ethernet/mellanox//mlx4/crdump.c:50:10: error: initializer
element is not constant
.name = region_fw_health_str,
The variables were made to be "const char * const", indicating that both
the pointer and data were constant. This was enough to resolve this on
recent GCC (gcc (GCC) 9.2.1 20190827 (Red Hat 9.2.1-1) for this author).
Unfortunately this is not enough for older compilers to realize that the
variable can be treated as a constant expression.
Fix this by introducing macros for the string and use those instead of
the variable name in the region ops structures.
Reported-by: tanhuazhong <tanhuazhong@huawei.com>
Fixes: e893768179 ("devlink: prepare to support region operations")
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert the mt7530 switch driver to use the finalised link
parameters in mac_link_up() rather than the parameters in mac_config().
Signed-off-by: René van Dorst <opensource@vdorst.com>
Tested-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It looks like the P/Q/R/S series supports some more counters,
generically named "Ethernet statistics counter", which we were not
printing. Add them.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Calling queue_delayed_work concurrently with
destroy_workqueue might race to an unexpected outcome -
scheduled task after wq is destroyed or other resources
(like ptt_pool) are freed (yields NULL pointer dereference).
cancel_delayed_work prevents the race by cancelling
the timer triggered for scheduling a new task.
Fixes: 59ccf86fe ("qed: Add driver infrastucture for handling mfw requests")
Signed-off-by: Denis Bolotin <dbolotin@marvell.com>
Signed-off-by: Michal Kalderon <mkalderon@marvell.com>
Signed-off-by: Yuval Basson <ybason@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The KSZ9131 provides DLL controlled delays on RXC and TXC lines. This
patch makes use of those delays. The information which delays should
be enabled or disabled comes from the interface names, documented in
ethernet-controller.yaml:
rgmii: Disable RXC and TXC delays
rgmii-id: Enable RXC and TXC delays
rgmii-txid: Enable only TXC delay, disable RXC delay
rgmii-rxid: Enable onlx RXC delay, disable TXC delay
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds new netlink attribute to allow a user to (optionally)
specify the desired offload mode immediately upon MACSec link creation.
Separate iproute patch will be required to support this from user space.
Signed-off-by: Mark Starovoytov <mstarovoitov@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Split the big recipe into 3 stages: compile, link, and hexdump.
After this commit, the build log with CONFIG_WANXL_BUILD_FIRMWARE
will look like this:
M68KAS drivers/net/wan/wanxlfw.o
M68KLD drivers/net/wan/wanxlfw.bin
BLDFW drivers/net/wan/wanxlfw.inc
CC [M] drivers/net/wan/wanxl.o
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
The firmware source, wanxlfw.S, is currently compiled by the combo of
$(CPP) and $(M68KAS). This is not what we usually do for compiling *.S
files. In fact, this Makefile is the only user of $(AS) in the kernel
build.
Instead of combining $(CPP) and (AS) from different tool sets, using
$(M68KCC) as an assembler driver is simpler, and saner.
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
As far as I understood from the Kconfig help text, this build rule is
used to rebuild the driver firmware, which runs on an old m68k-based
chip. So, you need m68k tools for the firmware rebuild.
wanxl.c is a PCI driver, but CONFIG_M68K does not select CONFIG_HAVE_PCI.
So, you cannot enable CONFIG_WANXL_BUILD_FIRMWARE for ARCH=m68k. In other
words, ifeq ($(ARCH),m68k) is false here.
I am keeping the dead code for now, but rebuilding the firmware requires
'as68k' and 'ld68k', which I do not have in hand.
Instead, the kernel.org m68k GCC [1] successfully built it.
Allowing a user to pass in CROSS_COMPILE_M68K= is handier.
[1] https://mirrors.edge.kernel.org/pub/tools/crosstool/files/bin/x86_64/9.2.0/x86_64-gcc-9.2.0-nolibc-m68k-linux.tar.xz
Suggested-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
The AER interfaces to clear error status registers were a confusing mess:
- pci_cleanup_aer_uncorrect_error_status() cleared non-fatal errors
from the Uncorrectable Error Status register.
- pci_aer_clear_fatal_status() cleared fatal errors from the
Uncorrectable Error Status register.
- pci_cleanup_aer_error_status_regs() cleared the Root Error Status
register (for Root Ports), the Uncorrectable Error Status register,
and the Correctable Error Status register.
Rename them to make them consistent:
From To
---------------------------------------- -------------------------------
pci_cleanup_aer_uncorrect_error_status() pci_aer_clear_nonfatal_status()
pci_aer_clear_fatal_status() pci_aer_clear_fatal_status()
pci_cleanup_aer_error_status_regs() pci_aer_clear_status()
Since pci_cleanup_aer_error_status_regs() (renamed to
pci_aer_clear_status()) is only used within drivers/pci/, move the
declaration from <linux/aer.h> to drivers/pci/pci.h.
[bhelgaas: commit log, add renames]
Link: https://lore.kernel.org/r/d1310a75dc3d28f7e8da4e99c45fbd3e60fe238e.1585000084.git.sathyanarayanan.kuppuswamy@linux.intel.com
Signed-off-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Changing the MTU for this switch means altering the
DEV_GMII:MAC_CFG_STATUS:MAC_MAXLEN_CFG field MAX_LEN, which in turn
limits the size of frames that can be received.
Special accounting needs to be done for the DSA CPU port (NPI port in
hardware terms). The NPI port configuration needs to be held inside the
private ocelot structure, since it is now accessed from multiple places.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of hardcoding the MTU to the maximum value allowed by the
hardware, obey the value known by the operating system.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On this switch, the frame length enforcements are performed by the
ingress policers. There are 2 types of those: regular L2 (also called
best-effort) and Virtual Link policers (an ARINC664/AFDX concept for
defining L2 streams with certain QoS abilities). To avoid future
confusion, I prefer to call the reset reason "Best-effort policers",
even though the VL policers are not yet supported.
We also need to change the setup of the initial static config, such that
DSA calls to .change_mtu (which are expensive) become no-ops and don't
reset the switch 5 times.
A driver-level decision is to unconditionally allow single VLAN-tagged
traffic on all ports. The CPU port must accept an additional VLAN header
for the DSA tag, which is again a driver-level decision.
The policers actually count bytes not only from the SDU, but also from
the Ethernet header and FCS, so those need to be accounted for as well.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It looks like the Broadcom switches supported by the b53 driver don't
support precise configuration of the MTU, but just a mumbo-jumbo boolean
flag. Set that.
Also configure BCM583XX devices to send and receive jumbo frames when
ports are configured with 10/100 Mbps speed.
Signed-off-by: Murali Krishna Policharla <murali.policharla@broadcom.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change DMA descriptor length to handle jumbo frames beyond 8192 bytes.
Also update jumbo frame max size to include FCS, the DMA packet length
received includes FCS.
Signed-off-by: Murali Krishna Policharla <murali.policharla@broadcom.com>
Reviewed-by: Arun Parameswaran <arun.parameswaran@broadcom.com>
Reviewed-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The BCM7XX PHY family requires special configuration to pass jumbo
frames. Do that during initial PHY setup.
Signed-off-by: Murali Krishna Policharla <murali.policharla@broadcom.com>
Reviewed-by: Scott Branden <scott.branden@broadcom.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On Android/x86 the module loading infrastructure can't deal with
softdeps. Therefore the check for presence of the Realtek PHY driver
module fails. mdiobus_register() will try to load the PHY driver
module, therefore move the check to after this call and explicitly
check that a dedicated PHY driver is bound to the PHY device.
Fixes: f325937735 ("r8169: check that Realtek PHY driver module is loaded")
Reported-by: Chih-Wei Huang <cwhuang@android-x86.org>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Third set of patches for v5.7. Nothing really special this time,
business as usual.
When pulling this to net-next there's again a conflict in:
drivers/net/wireless/intel/iwlwifi/pcie/drv.c
To solve this drop these three lines from the conflict (the first hunk
from "HEAD") as the whole AX200 block was moved above in the same
file:
IWL_DEV_INFO(0x2723, 0x1653, iwl_ax200_cfg_cc, iwl_ax200_killer_1650w_name),
IWL_DEV_INFO(0x2723, 0x1654, iwl_ax200_cfg_cc, iwl_ax200_killer_1650x_name),
IWL_DEV_INFO(0x2723, IWL_CFG_ANY, iwl_ax200_cfg_cc, iwl_ax200_name),
And keep all the __IWL_DEV_INFO() entries (the second hunk). In other
words, take everything from wireless-drivers-next. When running 'git
diff' after the resolution the output should be empty.
Major changes:
brcmfmac
* add USB autosuspend support
ath11k
* handle RX fragments
* enable PN offload
* add support for HE BSS color
iwlwifi
* support new FW API version
* support for EDCA measurements
* new scan API features
* enable new firmware debugging code
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJefdsZAAoJEG4XJFUm622blekH/2fIoUtl8Kdih38hNjz63PLD
x+LCPjZdRjrmFGTSxnS1rZiIM7v2yXyLGiyq+yr2ltzkpTi8xWOkKL6US8RCew9R
otRtZyLrhgMLG2ExDna1fI5ZJAtLnxV31TCy6yrSUDZ8t4VxMNIB4si3WRzKvAfU
c+cQcsnWr+pCDnbxh53BcYIyiEqKlttw/fGuIKchKuYMQy7DV6nxMdTaAym5Szzi
Nlb8fhXWFaPrPQ6NtHb5WWm4Er3wtMzN/AG8aFVxjrik07vTxQKWamdT9CeK2tDT
iDbx2HaNCWFMulXeZMrc9+inoAzj3UjbPqH3OTUk9iHbVA0unc3CdEBFD9h928Q=
=D/FA
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-2020-03-27' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for v5.7
Third set of patches for v5.7. Nothing really special this time,
business as usual.
When pulling this to net-next there's again a conflict in:
drivers/net/wireless/intel/iwlwifi/pcie/drv.c
To solve this drop these three lines from the conflict (the first hunk
from "HEAD") as the whole AX200 block was moved above in the same
file:
IWL_DEV_INFO(0x2723, 0x1653, iwl_ax200_cfg_cc, iwl_ax200_killer_1650w_name),
IWL_DEV_INFO(0x2723, 0x1654, iwl_ax200_cfg_cc, iwl_ax200_killer_1650x_name),
IWL_DEV_INFO(0x2723, IWL_CFG_ANY, iwl_ax200_cfg_cc, iwl_ax200_name),
And keep all the __IWL_DEV_INFO() entries (the second hunk). In other
words, take everything from wireless-drivers-next. When running 'git
diff' after the resolution the output should be empty.
Major changes:
brcmfmac
* add USB autosuspend support
ath11k
* handle RX fragments
* enable PN offload
* add support for HE BSS color
iwlwifi
* support new FW API version
* support for EDCA measurements
* new scan API features
* enable new firmware debugging code
====================
Kalle gave me directions on how to resolve the iwlwifi conflict
as follows:
====================
When pulling this to net-next there's again a conflict in:
drivers/net/wireless/intel/iwlwifi/pcie/drv.c
To solve this drop these three lines from the conflict (the first hunk
from "HEAD") as the whole AX200 block was moved above in the same
file:
IWL_DEV_INFO(0x2723, 0x1653, iwl_ax200_cfg_cc, iwl_ax200_killer_1650w_name),
IWL_DEV_INFO(0x2723, 0x1654, iwl_ax200_cfg_cc, iwl_ax200_killer_1650x_name),
IWL_DEV_INFO(0x2723, IWL_CFG_ANY, iwl_ax200_cfg_cc, iwl_ax200_name),
And keep all the __IWL_DEV_INFO() entries (the second hunk). In other
words, take everything from wireless-drivers-next. When running 'git
diff' after the resolution the output should be empty.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix macro names to report fw.mgmt and fw.ncsi versions to match the
devlink documentation.
Example display after fixes:
$ devlink dev info pci/0000:af:00.0
pci/0000:af:00.0:
driver bnxt_en
serial_number B0-26-28-FF-FE-25-84-20
versions:
fixed:
board.id BCM957454A4540
asic.id C454
asic.rev 1
running:
fw 216.1.154.0
fw.psid 0.0.0
fw.mgmt 216.1.146.0
fw.mgmt.api 1.10.1
fw.ncsi 864.0.44.0
fw.roce 216.1.16.0
Fixes: 9599e036b1 ("bnxt_en: Add support for devlink info command")
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add part number info from the vital product data to info_get command
via devlink tool. Update bnxt.rst documentation as well.
Cc: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Store the part number and serial number information from VPD in
the bnxt structure. Follow up patch will add the support to display
the information via devlink command.
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Display the minimum version of firmware interface spec supported
between driver and firmware. Also update bnxt.rst documentation file.
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Suppress the following smatch errors. None of these are actually
possible with current code paths.
drivers/net/ethernet/mellanox/mlxsw//spectrum_router.c:1220
mlxsw_sp_ipip_entry_find_decap() error: uninitialized symbol 'saddrp'.
drivers/net/ethernet/mellanox/mlxsw//spectrum_router.c:1220
mlxsw_sp_ipip_entry_find_decap() error: uninitialized symbol
'saddr_len'.
drivers/net/ethernet/mellanox/mlxsw//spectrum_router.c:1221
mlxsw_sp_ipip_entry_find_decap() error: uninitialized symbol
'saddr_prefix_len'.
drivers/net/ethernet/mellanox/mlxsw/spectrum_router.c:1390
mlxsw_sp_netdevice_ipip_ol_reg_event() error: uninitialized symbol
'ipipt'.
drivers/net/ethernet/mellanox/mlxsw/spectrum_router.c:3255
mlxsw_sp_nexthop_group_update() error: uninitialized symbol 'err'.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Suppress following warning from coccinelle:
drivers/net/ethernet/mellanox/mlxsw//switchx2.c:183:63-68: WARNING:
conversion to bool not needed here
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The static array 'mlxsw_afk_element_infos' in 'core_acl_flex_keys.h' is
copied to each file that includes the header, but not all use it. This
results in the following warnings when compiling with W=1:
drivers/net/ethernet/mellanox/mlxsw//core_acl_flex_keys.h:76:44:
warning: ‘mlxsw_afk_element_infos’ defined but not used
[-Wunused-const-variable=]
One way to suppress the warning is to mark the array with
'__maybe_unused', but another option is to remove it from the header
file entirely.
Change 'struct mlxsw_afk_element_inst' to store the key to the array
('element') instead of the array value keyed by 'element'. Adjust the
different users accordingly.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In merge commit 50853808ff ("Merge branch
'mlxsw-Prepare-for-VLAN-aware-bridge-w-VxLAN'") I flipped mlxsw to use
emulated 802.1Q FIDs and correspondingly emulated VLAN RIFs. This means
that the non-emulated variants are no longer used. Remove them and
suppress the following warnings when compiling with W=1:
drivers/net/ethernet/mellanox/mlxsw//spectrum_router.c:7572:38: warning:
‘mlxsw_sp_rif_vlan_ops’ defined but not used [-Wunused-const-variable=]
drivers/net/ethernet/mellanox/mlxsw//spectrum_fid.c:584:41: warning:
‘mlxsw_sp_fid_8021q_family’ defined but not used
[-Wunused-const-variable=]
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Suppress following warnings when compiling with W=1:
drivers/net/ethernet/mellanox/mlxsw//spectrum_router.c:1552: warning:
Function parameter or member 'mlxsw_sp' not described in
'__mlxsw_sp_ipip_entry_update_tunnel'
drivers/net/ethernet/mellanox/mlxsw//spectrum_router.c:1552: warning:
Function parameter or member 'ipip_entry' not described in
'__mlxsw_sp_ipip_entry_update_tunnel'
drivers/net/ethernet/mellanox/mlxsw//spectrum_router.c:1552: warning:
Function parameter or member 'extack' not described in
'__mlxsw_sp_ipip_entry_update_tunnel'
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Suppress following warning when compiling with W=1:
drivers/net/ethernet/mellanox/mlxsw//i2c.c:78: warning: Function
parameter or member 'cmd' not described in 'mlxsw_i2c'
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Leon Romanovsky says:
====================
Those two patches from Michael extends mlx5_core and mlx5_ib flow steering
to support RDMA TX in similar way to already supported RDMA RX.
====================
Based on the mlx5-next branch at
git://git.kernel.org/pub/scm/linux/kernel/git/mellanox/linux
Due to dependencies
* branch 'mlx5_tx_steering':
RDMA/mlx5: Add support for RDMA TX flow table
net/mlx5: Add support for RDMA TX steering
Add new RDMA TX flow steering namespace. Flow steering rules in
this namespace are used to filter transmitted RDMA traffic.
Link: https://lore.kernel.org/r/20200324061425.1570190-2-leon@kernel.org
Signed-off-by: Michael Guralnik <michaelgur@mellanox.com>
Reviewed-by: Maor Gottlieb <maorg@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Some of the places using this want the newline, but not all,
so remove the newline from it and generate it in the debugfs
files where it's desired.
The effect of this is not printing double newlines in debug
log messages.
Change-Id: Ia59b0abbef16b6783fcabc095c5fde16bd047a26
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
There's no need for this to be exposed outside of the tx.c
file, make it static.
Change-Id: I41d40008311b108d0578bd2ec73c5477e700a839
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Start supporting API version 53 for 22000 series.
Change-Id: I5725e46394f3f53c3069723fd513cc53c7df383d
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This is used to initialize the default value, but refers back
to the value itself, essentially leading to a
val = val
assignment at init time ... that's useless, remove it and use
_NODEF.
Change-Id: I725923016563c34ce2fa057bf7c12984e1041c49
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Now that YoYo is more mature, we can enable it by default, so we
collect data in the new way.
Change-Id: Ic1a147f935286b085ca8bdb248a7493b7c6341ea
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The FW changed the maximum number of scan offload profiles to 8 in new
APIs. Support it by changing the scan_offload_profile_cfg struct to be
more dynamic, so we can reuse most of the code and only change size of
the profiles array.
Change-Id: I65210cf541af46e2675a8c764d5871f7f5b070d6
Signed-off-by: Tova Mussai <tova.mussai@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When we have an assert during D3 we want to dump the internal
buffer memory even if are we working in DRAM debug mode. We should not
block dumping it.
Change-Id: I69aad2d4904c4f8bb653c61e8781a2e07780054f
Signed-off-by: Rotem Saado <rotem.saado@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We don't support the FPGA versions of this card combination anymore.
Remove the cfg mangling that tries to load it and all the relevant
structures.
Change-Id: I190652101afcab682cfba873d062992f11efca32
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We don't support QnJ HR STEP A anymore. Remove the structures we used
for it.
Change-Id: I0dfd88232bdc8ff2dd9c4368b8ed9a0c40c86bc8
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
A couple of SoCs, which can be recognized by PCI device IDs 0xA0F0 and
0x43F0, need a longer wait for the xtal to stabilize. To handle this,
add a new trans_cfg structure for Qu devices with a larger
xtal_latency value and apply them to the devices recognized by these
IDs. Also add a flag that allows us to inform the FW that the low
latency xtal should be used.
Change-Id: I8a14c6af45ea14d8e7f1ef38a589158f38d0c0ea
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This new command is mostly backwards compatible, with the exception
that the device_type element was changed into a bitmask. The device
type bit remains the same (because we only had 0 and 1 anyway), but
when using v1 we can't set any other bits, because that would change
the integer.
Other than that, the struct remains the same and the driver can set
the device_type bit in both cases, but it can only set the low_latency
bit if VER_2 is used.
Change-Id: Ib68d4c821ebcce253b42ed0ea15881fb4e3e01da
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Now that we identify the correct cfgs with the new tables for Qu step
C and QuZ with Jf, we can remove the mangling we do later on.
Change-Id: Ic01ce67db147e897ad2424f0e05a70a00d2c620e
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
All the QnJ devices have a similar matching to the other Qu devices,
but needs a different configuration. Convert the QnJ devices to the
new table accordingly.
Change-Id: If236ef3d0da3e605a3379922818f5897e0affd7e
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add new generic iwl_trans structures for these devices and apply the
correct cfg depending on the device characteristics.
Since we have to match Qu with IWL_CONFIG_ANY, we also need to move
the Hr devices to the new table, but for now we keep matching on PCI
device and subsystem device IDs.
Change-Id: I14e9146a99621ff11ce50bc746a4b88af508fee0
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We need to use different firmware versions for different HW steps with
certain devices. Prepare for this differentiation by adding HW step
to the new device table.
Change-Id: Ib1afb7b0c89e9dc2d26e6d32ea19e978c17ba1dd
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
After the refactoring, a few extern declarations were accidentally
left in the iwl-config.h file. Remove them
Change-Id: I79745e440ed5a0a90db61b0daaae374ecef09e86
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
These values are selected based on the PCI device ID, so the decision
to use them can be made early. By moving them to the trans_cfg, we
avoid duplicating the large cfg structs for small pieces of
data (sometimes a single boolean). This will also allow us to make
more decisions based on, for instance, the SoC type in used.
The trans_cfg concept changes a bit, because previously it was used
only to boot the device before reading further characteristics and now
it also contains more data that is associated with the device ID.
Change-Id: Ib71b07ea9e322eb74571dc5e8aa58f17eece5c9c
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We shouldn't do this just for HT/VHT, but be future-proof
and also check for HE.
Change-Id: Icaeff714c00a773681dbfee72558afd1c7121c5d
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>