Fixes the following sparse warnings:
drivers/power/ipaq_micro_battery.c:278:24: warning:
symbol 'micro_batt_device_driver' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
This adds a driver for reading the battery status of the
battery connected to the Atmel microcontroller on the
iPAQ h3xxx series.
Based on a driver from handhelds.org 2.6.21 kernel, written
by Alessandro GARDICH.
Signed-off-by: Dmitry Artamonow <mad_soft@inbox.ru>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
TWL4030's Battery Charger seems to be designed for non-hotpluggable
batteries.
If battery is not present in the system, BATSTS is always set with the
expectation that software will take actions to move to a required safe
state (could be power down or disable various charger paths).
It does not seem possible even by manipulating the edge detection
of the event (using BCIEDR2 register) to have a consistent hotplug
handling. This seems to be the result of BATSTS interrupt generated
when the thermistor of the battery pack is disconnected from the
dedicated ADIN1 pin. Clearing the status just results in the status
being regenerated by the monitoring ADC(MADC) and disabling the
edges of event just makes hotplug no longer function. The only
other option is to disable the detection of the MADC by disabling
BCIMFEN4::BATSTSMCHGEN (battery presence detector) - but then, we can
never again detect battery reconnection.
So, detect battery presence based on precharge(which is hardware
automatic state) or default main charger configuration at the time of
probe and enable charger logic only if battery was present.
Reported-by: Russell King <linux@arm.linux.org.uk>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Add support for reboot functionality on boards with ARM-based
Broadcom STB chipsets. Make it built-in by default for ARCH_BRCMSTB,
but allow it to be configurable under COMPILE_TEST.
Signed-off-by: Marc Carino <marc.ceeeee@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Fixes the following sparse warnings:
drivers/power/power_supply_core.c:540:5: warning:
symbol '__power_supply_register' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Add new power supply properties for input current, charge termination
current, min and max temperature
POWER_SUPPLY_PROP_TEMP_MIN - minimum operatable temperature
POWER_SUPPLY_PROP_TEMP_MAX - maximum operatable temperature
POWER_SUPPLY_PROP_INPUT_CURRENT_LIMIT - input current limit programmed
by charger. Indicates the input current for a charging source.
POWER_SUPPLY_PROP_CHARGE_TERM_CURRENT - Charge termination current used
to detect the end of charge condition
Signed-off-by: Jenny TC <jenny.tc@intel.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
On the ARM Chromebook tps65090 has two masters: the AP (the main
processor running linux) and the EC (the embedded controller). The AP
is allowed to mess with FETs but the EC is in charge of charge control.
The tps65090 interupt line is routed to both the AP and the EC, which
can cause quite a headache. Having two people adjusting masks and
acking interrupts is a recipe for disaster.
In the shipping kernel we had a hack to have the AP pay attention to
the IRQ but not to ack it. It also wasn't supposed to configure the
IRQ in any way. That hack allowed us to detect when the device was
charging without messing with the EC's state.
The current tps65090 infrastructure makes the above difficult, and it
was a bit of a hack to begin with. Rather than uglify the driver to
support it, just extend the driver's existing notion of "no irq" to
the charger. This makes the charger code poll every 2 seconds for AC
detect, which is sufficient.
For proper functioning, requires (mfd: tps65090: Don't tell child
devices we have an IRQ if we don't). If we don't have that patch
we'll simply fail to probe on devices without an interrupt (just like
we did before this patch).
Signed-off-by: Doug Anderson <dianders@chromium.org>
Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Tested-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
[sre@kernel.org: Use -ENXIO instead of NO_IRQ for missing interrupt,
since NO_IRQ is not available on all architectures.]
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Per license_is_gpl_compatible(), the MODULE_LICENSE() string for GPL v2 is
"GPL v2", not "GPLv2". Use "GPL v2" so this module doesn't taint the
kernel.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
This switches the GPIO poweroff driver to use GPIO descriptors
rather than numeral GPIOs. We get rid of the specific inversion
handling as GPIO descriptors know if they are active low or
high and can assert the line properly, so we do not need to
check the flag OF_GPIO_ACTIVE_LOW returned from the old call
of_get_gpio_flags() anymore.
Also convert to use managed resources and use dev_* message
printing while we're at it.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
One an hdq buss, a missing device reads as 0xff, not -1.
So do a translation to allow detecting of a missing bus.
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
This patch moves data allocated using kzalloc to managed data allocated
using devm_kzalloc and cleans now unnecessary kfrees in probe and remove
functions for both platform and i2c drivers. Also, the unecessary
variable ret and labels batt_failed3, err_free were removed.
The following Coccinele script was used for making the change:
@platform@
identifier p, probefn, removefn;
@@
struct platform_driver p = {
.probe = probefn,
.remove = removefn,
};
@prb@
identifier platform.probefn, pdev;
expression e, e1, e2;
@@
probefn(struct platform_device *pdev, ...) {
<+...
- e = kzalloc(e1, e2)
+ e = devm_kzalloc(&pdev->dev, e1, e2)
...
?-kfree(e);
...+>
}
@rem depends on prb@
identifier platform.removefn;
expression e;
@@
removefn(...) {
<...
- kfree(e);
...>
}
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Add a driver to handle the shutdown of the Atmel SoCs. This code used to be
(and still is) in arch/arm/mach-at91. We didn't remove it yet so that we can
convert all the boards to using this driver, before removing it entirely in a
separate patch.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Implement the reset behaviour of the various AT91 SoCS in drivers/power/reset.
It used to be (and still is) located in arch/arm/mach-at91, and in order to
preserve bisectability is not removed yet, but every board should be converted
to use this driver instead.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
All the config option so far are depending on the POWER_RESET symbol
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
- ACPICA update to upstream version 20140424. That includes a
number of fixes and improvements related to things like GPE
handling, table loading, headers, memory mapping and unmapping,
DSDT/SSDT overriding, and the Unload() operator. The acpidump
utility from upstream ACPICA is included too. From Bob Moore,
Lv Zheng, David Box, David Binderman, and Colin Ian King.
- Fixes and cleanups related to ACPI video and backlight interfaces
from Hans de Goede. That includes blacklist entries for some new
machines and using native backlight by default.
- ACPI device enumeration changes to create platform devices
rather than PNP devices for ACPI device objects with _HID by
default. PNP devices will still be created for the ACPI device
object with device IDs corresponding to real PNP devices, so
that change should not break things left and right, and we're
expecting to see more and more ACPI-enumerated platform devices
in the future. From Zhang Rui and Rafael J Wysocki.
- Updates for the ACPI LPSS (Low-Power Subsystem) driver allowing
it to handle system suspend/resume on Asus T100 correctly.
From Heikki Krogerus and Rafael J Wysocki.
- PM core update introducing a mechanism to allow runtime-suspended
devices to stay suspended over system suspend/resume transitions
if certain additional conditions related to coordination within
device hierarchy are met. Related PM documentation update and
ACPI PM domain support for the new feature. From Rafael J Wysocki.
- Fixes and improvements related to the "freeze" sleep state. They
affect several places including cpuidle, PM core, ACPI core, and
the ACPI battery driver. From Rafael J Wysocki and Zhang Rui.
- Miscellaneous fixes and updates of the ACPI core from Aaron Lu,
Bjørn Mork, Hanjun Guo, Lan Tianyu, and Rafael J Wysocki.
- Fixes and cleanups for the ACPI processor and ACPI PAD (Processor
Aggregator Device) drivers from Baoquan He, Manuel Schölling,
Tony Camuso, and Toshi Kani.
- System suspend/resume optimization in the ACPI battery driver from
Lan Tianyu.
- OPP (Operating Performance Points) subsystem updates from
Chander Kashyap, Mark Brown, and Nishanth Menon.
- cpufreq core fixes, updates and cleanups from Srivatsa S Bhat,
Stratos Karafotis, and Viresh Kumar.
- Updates, fixes and cleanups for the Tegra, powernow-k8, imx6q,
s5pv210, nforce2, and powernv cpufreq drivers from Brian Norris,
Jingoo Han, Paul Bolle, Philipp Zabel, Stratos Karafotis, and
Viresh Kumar.
- intel_pstate driver fixes and cleanups from Dirk Brandewie,
Doug Smythies, and Stratos Karafotis.
- Enabling the big.LITTLE cpufreq driver on arm64 from Mark Brown.
- Fix for the cpuidle menu governor from Chander Kashyap.
- New ARM clps711x cpuidle driver from Alexander Shiyan.
- Hibernate core fixes and cleanups from Chen Gang, Dan Carpenter,
Fabian Frederick, Pali Rohár, and Sebastian Capella.
- Intel RAPL (Running Average Power Limit) driver updates from
Jacob Pan.
- PNP subsystem updates from Bjorn Helgaas and Fabian Frederick.
- devfreq core updates from Chanwoo Choi and Paul Bolle.
- devfreq updates for exynos4 and exynos5 from Chanwoo Choi and
Bartlomiej Zolnierkiewicz.
- turbostat tool fix from Jean Delvare.
- cpupower tool updates from Prarit Bhargava, Ramkumar Ramachandra
and Thomas Renninger.
- New ACPI ec_access.c tool for poking at the EC in a safe way
from Thomas Renninger.
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=tpdF
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-3.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm into next
Pull ACPI and power management updates from Rafael Wysocki:
"ACPICA is the leader this time (63 commits), followed by cpufreq (28
commits), devfreq (15 commits), system suspend/hibernation (12
commits), ACPI video and ACPI device enumeration (10 commits each).
We have no major new features this time, but there are a few
significant changes of how things work. The most visible one will
probably be that we are now going to create platform devices rather
than PNP devices by default for ACPI device objects with _HID. That
was long overdue and will be really necessary to be able to use the
same drivers for the same hardware blocks on ACPI and DT-based systems
going forward. We're not expecting fallout from this one (as usual),
but it's something to watch nevertheless.
The second change having a chance to be visible is that ACPI video
will now default to using native backlight rather than the ACPI
backlight interface which should generally help systems with broken
Win8 BIOSes. We're hoping that all problems with the native backlight
handling that we had previously have been addressed and we are in a
good enough shape to flip the default, but this change should be easy
enough to revert if need be.
In addition to that, the system suspend core has a new mechanism to
allow runtime-suspended devices to stay suspended throughout system
suspend/resume transitions if some extra conditions are met
(generally, they are related to coordination within device hierarchy).
However, enabling this feature requires cooperation from the bus type
layer and for now it has only been implemented for the ACPI PM domain
(used by ACPI-enumerated platform devices mostly today).
Also, the acpidump utility that was previously shipped as a separate
tool will now be provided by the upstream ACPICA along with the rest
of ACPICA code, which will allow it to be more up to date and better
supported, and we have one new cpuidle driver (ARM clps711x).
The rest is improvements related to certain specific use cases,
cleanups and fixes all over the place.
Specifics:
- ACPICA update to upstream version 20140424. That includes a number
of fixes and improvements related to things like GPE handling,
table loading, headers, memory mapping and unmapping, DSDT/SSDT
overriding, and the Unload() operator. The acpidump utility from
upstream ACPICA is included too. From Bob Moore, Lv Zheng, David
Box, David Binderman, and Colin Ian King.
- Fixes and cleanups related to ACPI video and backlight interfaces
from Hans de Goede. That includes blacklist entries for some new
machines and using native backlight by default.
- ACPI device enumeration changes to create platform devices rather
than PNP devices for ACPI device objects with _HID by default. PNP
devices will still be created for the ACPI device object with
device IDs corresponding to real PNP devices, so that change should
not break things left and right, and we're expecting to see more
and more ACPI-enumerated platform devices in the future. From
Zhang Rui and Rafael J Wysocki.
- Updates for the ACPI LPSS (Low-Power Subsystem) driver allowing it
to handle system suspend/resume on Asus T100 correctly. From
Heikki Krogerus and Rafael J Wysocki.
- PM core update introducing a mechanism to allow runtime-suspended
devices to stay suspended over system suspend/resume transitions if
certain additional conditions related to coordination within device
hierarchy are met. Related PM documentation update and ACPI PM
domain support for the new feature. From Rafael J Wysocki.
- Fixes and improvements related to the "freeze" sleep state. They
affect several places including cpuidle, PM core, ACPI core, and
the ACPI battery driver. From Rafael J Wysocki and Zhang Rui.
- Miscellaneous fixes and updates of the ACPI core from Aaron Lu,
Bjørn Mork, Hanjun Guo, Lan Tianyu, and Rafael J Wysocki.
- Fixes and cleanups for the ACPI processor and ACPI PAD (Processor
Aggregator Device) drivers from Baoquan He, Manuel Schölling, Tony
Camuso, and Toshi Kani.
- System suspend/resume optimization in the ACPI battery driver from
Lan Tianyu.
- OPP (Operating Performance Points) subsystem updates from Chander
Kashyap, Mark Brown, and Nishanth Menon.
- cpufreq core fixes, updates and cleanups from Srivatsa S Bhat,
Stratos Karafotis, and Viresh Kumar.
- Updates, fixes and cleanups for the Tegra, powernow-k8, imx6q,
s5pv210, nforce2, and powernv cpufreq drivers from Brian Norris,
Jingoo Han, Paul Bolle, Philipp Zabel, Stratos Karafotis, and
Viresh Kumar.
- intel_pstate driver fixes and cleanups from Dirk Brandewie, Doug
Smythies, and Stratos Karafotis.
- Enabling the big.LITTLE cpufreq driver on arm64 from Mark Brown.
- Fix for the cpuidle menu governor from Chander Kashyap.
- New ARM clps711x cpuidle driver from Alexander Shiyan.
- Hibernate core fixes and cleanups from Chen Gang, Dan Carpenter,
Fabian Frederick, Pali Rohár, and Sebastian Capella.
- Intel RAPL (Running Average Power Limit) driver updates from Jacob
Pan.
- PNP subsystem updates from Bjorn Helgaas and Fabian Frederick.
- devfreq core updates from Chanwoo Choi and Paul Bolle.
- devfreq updates for exynos4 and exynos5 from Chanwoo Choi and
Bartlomiej Zolnierkiewicz.
- turbostat tool fix from Jean Delvare.
- cpupower tool updates from Prarit Bhargava, Ramkumar Ramachandra
and Thomas Renninger.
- New ACPI ec_access.c tool for poking at the EC in a safe way from
Thomas Renninger"
* tag 'pm+acpi-3.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (187 commits)
ACPICA: Namespace: Remove _PRP method support.
intel_pstate: Improve initial busy calculation
intel_pstate: add sample time scaling
intel_pstate: Correct rounding in busy calculation
intel_pstate: Remove C0 tracking
PM / hibernate: fixed typo in comment
ACPI: Fix x86 regression related to early mapping size limitation
ACPICA: Tables: Add mechanism to control early table checksum verification.
ACPI / scan: use platform bus type by default for _HID enumeration
ACPI / scan: always register ACPI LPSS scan handler
ACPI / scan: always register memory hotplug scan handler
ACPI / scan: always register container scan handler
ACPI / scan: Change the meaning of missing .attach() in scan handlers
ACPI / scan: introduce platform_id device PNP type flag
ACPI / scan: drop unsupported serial IDs from PNP ACPI scan handler ID list
ACPI / scan: drop IDs that do not comply with the ACPI PNP ID rule
ACPI / PNP: use device ID list for PNPACPI device enumeration
ACPI / scan: .match() callback for ACPI scan handlers
ACPI / battery: wakeup the system only when necessary
power_supply: allow power supply devices registered w/o wakeup source
...
The bulk of the changes for this release are a few new drivers however
there are a couple of noticable core changes and the usual stream of
cleanups and fixes:
- Move disable of unused regulators later in init so it comes after
deferred probe has iterated making startup smoother.
- Fixes reference counting of the DT nodes for constraints from Charles
Keepax. This has little practical impact since all real users of
the regulator bindings use FDT which doesn't need the reference
counting.
- Lots of cleanups, especially to the Samsung drivers.
- Support for Linear Technologies LTC3589, Texas Instruments TPS658640
and X-Powers AXP20x.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=JrfM
-----END PGP SIGNATURE-----
Merge tag 'regulator-v3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator into next
Pull regulator updates from Mark Brown:
"The bulk of the changes for this release are a few new drivers however
there are a couple of noticable core changes and the usual stream of
cleanups and fixes:
- move disable of unused regulators later in init so it comes after
deferred probe has iterated making startup smoother.
- fixes to reference counting of the DT nodes for constraints from
Charles Keepax. This has little practical impact since all real
users of the regulator bindings use FDT which doesn't need the
reference counting.
- lots of cleanups, especially to the Samsung drivers.
- support for Linear Technologies LTC3589, Texas Instruments
TPS658640 and X-Powers AXP20x"
* tag 'regulator-v3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator: (64 commits)
regulator: pbias: remove unnecessary OOM messages
regulator: max8649: remove unnecessary OOM messages
regulator: core: Fix the init of DT defined fixed regulators
regulator: core: Disable unused regulators after deferred probing is done
regulator: Don't disable unused regulators we don't have permission for
regulator: axp20x: Use regulator_map_voltage_ascend for LDO4
regulator: use of_property_read_{bool|u32}()
regulator: Fix regulator_get_{optional,exclusive}() documentation
regulators: Add definition of regulator_set_voltage_time() for !CONFIG_REGULATOR
regulator: arizona-ldo1: add missing #include
regulator: pfuze100: Support enable/disable for fixed regulator
regulator: ltc3589: Remove ltc3589_list_voltage_fixed function
regulator: ltc3589: Fix module dependency
regulator: tps6586x: Remove unused to_tps6586x_dev() function
regulator: tps65218: Convert to use regulator_set_voltage_time_sel
regulator: tps6586x: Add support for the TPS658640
regulator: tps6586x: Prepare supporting fixed regulators
regulator: pfuze100: Don't allocate an invalid gpio
regulator: pfuze100: Support SWB enable/disable
regulator: fixed: use of_property_read_{bool|u32}()
...
SoC-near driver changes that we're merging through our tree. Mostly
because they depend on other changes we have staged, but in some cases
because the driver maintainers preferred that we did it this way.
This contains a largeish cleanup series of the omap_l3_noc bus driver,
cpuidle rework for Exynos, some reset driver conversions and a long
branch of TI EDMA fixes and cleanups, with more to come next release.
The TI EDMA cleanups is a shared branch with the dmaengine tree, with
a handful of Davinci-specific fixes on top.
After discussion at last year's KS (and some more on the mailing lists),
we are here adding a drivers/soc directory. The purpose of this is
to keep per-vendor shared code that's needed by different drivers but
that doesn't fit into the MFD (nor drivers/platform) model. We expect
to keep merging contents for this hierarchy through arm-soc so we can
keep an eye on what the vendors keep adding here and not making it a
free-for-all to shove in crazy stuff.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=SC+e
-----END PGP SIGNATURE-----
Merge tag 'drivers-for-3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc into next
Pull ARM SoC driver changes from Olof Johansson:
"SoC-near driver changes that we're merging through our tree. Mostly
because they depend on other changes we have staged, but in some cases
because the driver maintainers preferred that we did it this way.
This contains a largeish cleanup series of the omap_l3_noc bus driver,
cpuidle rework for Exynos, some reset driver conversions and a long
branch of TI EDMA fixes and cleanups, with more to come next release.
The TI EDMA cleanups is a shared branch with the dmaengine tree, with
a handful of Davinci-specific fixes on top.
After discussion at last year's KS (and some more on the mailing
lists), we are here adding a drivers/soc directory. The purpose of
this is to keep per-vendor shared code that's needed by different
drivers but that doesn't fit into the MFD (nor drivers/platform)
model. We expect to keep merging contents for this hierarchy through
arm-soc so we can keep an eye on what the vendors keep adding here and
not making it a free-for-all to shove in crazy stuff"
* tag 'drivers-for-3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (101 commits)
cpufreq: exynos: Fix driver compilation with ARCH_MULTIPLATFORM
tty: serial: msm: Remove direct access to GSBI
power: reset: keystone-reset: introduce keystone reset driver
Documentation: dt: add bindings for keystone pll control controller
Documentation: dt: add bindings for keystone reset driver
soc: qcom: fix of_device_id table
ARM: EXYNOS: Fix kernel panic when unplugging CPU1 on exynos
ARM: EXYNOS: Move the driver to drivers/cpuidle directory
ARM: EXYNOS: Cleanup all unneeded headers from cpuidle.c
ARM: EXYNOS: Pass the AFTR callback to the platform_data
ARM: EXYNOS: Move S5P_CHECK_SLEEP into pm.c
ARM: EXYNOS: Move the power sequence call in the cpu_pm notifier
ARM: EXYNOS: Move the AFTR state function into pm.c
ARM: EXYNOS: Encapsulate the AFTR code into a function
ARM: EXYNOS: Disable cpuidle for exynos5440
ARM: EXYNOS: Encapsulate boot vector code into a function for cpuidle
ARM: EXYNOS: Pass wakeup mask parameter to function for cpuidle
ARM: EXYNOS: Remove ifdef for scu_enable in pm
ARM: EXYNOS: Move scu_enable in the cpu_pm notifier
ARM: EXYNOS: Use the cpu_pm notifier for pm
...
A quite large set of SoC updates this cycle. In no particular order:
- Multi-cluster power management for Samsung Exynos, adding support for
big.LITTLE CPU switching on EXYNOS5
- SMP support for Marvell Armada 375 and 38x
- SMP rework on Allwinner A31
- Xilinx Zynq support for SOC_BUS, big endian
- Marvell orion5x platform cleanup, modernizing the implementation and
moving to DT.
- _Finally_ moving Samsung Exynos over to support MULTIPLATFORM, so
that their platform can be enabled in the same kernel binary as most
of the other v7 platforms in the tree. \o/ The work isn't quite complete,
there's some driver fixes still needed, but the basics now work.
New SoC support added:
- Freescale i.MX6SX
- LSI Axxia AXM55xx SoCs
- Samsung EXYNOS 3250, 5260, 5410, 5420 and 5800
- STi STIH407
Plus a large set of various smaller updates for different platforms. I'm
probably missing some important one here.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=6LYI
-----END PGP SIGNATURE-----
Merge tag 'soc-for-3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc into next
Pull part one of ARM SoC updates from Olof Johansson:
"A quite large set of SoC updates this cycle. In no particular order:
- Multi-cluster power management for Samsung Exynos, adding support
for big.LITTLE CPU switching on EXYNOS5
- SMP support for Marvell Armada 375 and 38x
- SMP rework on Allwinner A31
- Xilinx Zynq support for SOC_BUS, big endian
- Marvell orion5x platform cleanup, modernizing the implementation
and moving to DT.
- _Finally_ moving Samsung Exynos over to support MULTIPLATFORM, so
that their platform can be enabled in the same kernel binary as
most of the other v7 platforms in the tree. \o/
The work isn't quite complete, there's some driver fixes still
needed, but the basics now work.
New SoC support added:
- Freescale i.MX6SX
- LSI Axxia AXM55xx SoCs
- Samsung EXYNOS 3250, 5260, 5410, 5420 and 5800
- STi STIH407
plus a large set of various smaller updates for different platforms.
I'm probably missing some important one here"
* tag 'soc-for-3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (281 commits)
ARM: exynos: don't run exynos4 l2x0 setup on other platforms
ARM: exynos: Fix "allmodconfig" build errors in mcpm and hotplug
ARM: EXYNOS: mcpm rename the power_down_finish
ARM: EXYNOS: Enable mcpm for dual-cluster exynos5800 SoC
ARM: EXYNOS: Enable multi-platform build support
ARM: EXYNOS: Consolidate Kconfig entries
ARM: EXYNOS: Add support for EXYNOS5410 SoC
ARM: EXYNOS: Support secondary CPU boot of Exynos3250
ARM: EXYNOS: Add Exynos3250 SoC ID
ARM: EXYNOS: Add 5800 SoC support
ARM: EXYNOS: initial board support for exynos5260 SoC
clk: exynos5410: register clocks using common clock framework
ARM: debug: qcom: add UART addresses to Kconfig help for APQ8084
ARM: sunxi: allow building without reset controller
Documentation: devicetree: arm: sort enable-method entries
ARM: rockchip: convert smp bringup to CPU_METHOD_OF_DECLARE
clk: exynos5250: Add missing sysmmu clocks for DISP and ISP blocks
ARM: dts: axxia: Add reset controller
power: reset: Add Axxia system reset driver
ARM: axxia: Adding defconfig for AXM55xx
...
Currently, all the power supply devices are registered with wakeup source,
this results in that every power_supply_changed() invocation brings
the system out of suspend-to-freeze state.
This is overkill as some device drivers, e.g. ACPI battery driver,
have the ability to check the device status and wake up the system
from sleeping only when necessary.
Thus introduce a new API which allows device to be registered
w/o wakeup source.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The keystone SoC can be rebooted in several ways. By external reset
pin, by soft and by watchdogs. To allow keystone SoC reset if
watchdog is triggered we have to enable it in reset mux configuration
register regarding of watchdog configuration. Also we need to set
soft/hard reset we are going to use.
So add keystone reset driver to handle all this stuff.
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Patches from Anders Berg applied individually:
Here is version 4 of platform support for AXM5516 SoC.
The clk driver is now applied to clk-next. The rest should be ready for
arm-soc. Haven't got any response from the power/reset maintainers... I hope
this driver can be taken via arm-soc as well.
The AXM55xx family consists of devices that may contain up to 16 ARM Cortex-A15
cores (in a 4x4 cluster configuration). The cores within each cluster share an
L2 cache, and the clusters are connected to each other via a CCN-504 cache
coherent interconnect.
This machine requires CONFIG_ARM_LPAE enabled as all peripherals are located
above 4GB in the memory map.
* axxia/soc:
ARM: dts: axxia: Add reset controller
power: reset: Add Axxia system reset driver
ARM: axxia: Adding defconfig for AXM55xx
ARM: dts: Device tree for AXM55xx.
ARM: Add platform support for LSI AXM55xx SoC
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
That code used to be in the machine code, but it's more fit here with other
restart hooks.
That will allow to cleanup the machine directory, while waiting for a proper
watchdog driver for the A31.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Components of the Versatile Express platform (configuration
microcontrollers on motherboard and daughterboards in particular)
talk to each other over a custom configuration bus. They
provide miscellaneous functions (from clock generator control
to energy sensors) which are represented as platform devices
(and Device Tree nodes). The transactions on the bus can
be generated by different "bridges" in the system, some
of which are universal for the whole platform (for the price
of high transfer latencies), others restricted to a subsystem
(but much faster).
Until now drivers for such functions were using custom "func"
API, which is being replaced in this patch by regmap calls.
This required:
* a rework (and move to drivers/bus directory, as suggested
by Samuel and Arnd) of the config bus core, which is much
simpler now and uses device model infrastructure (class)
to keep track of the bridges; non-DT case (soon to be
retired anyway) is simply covered by a special device
registration function
* the new config-bus driver also takes over device population,
so there is no need for special matching table for
of_platform_populate nor "simple-bus" hack in the arm64
model dtsi file (relevant bindings documentation has
been updated); this allows all the vexpress devices
fit into normal device model, making it possible
to remove plenty of early inits and other hacks in
the near future
* adaptation of the syscfg bridge implementation in the
sysreg driver, again making it much simpler; there is
a special case of the "energy" function spanning two
registers, where they should be both defined in the tree
now, but backward compatibility is maintained in the code
* modification of the relevant drivers:
* hwmon - just a straight-forward API change
* power/reset driver - API change
* regulator - API change plus error handling
simplification
* osc clock driver - this one required larger rework
in order to turn in into a standard platform driver
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
Acked-by: Mark Brown <broonie@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Mike Turquette <mturquette@linaro.org>
The restart/power off implementation in the vexpress driver
used to obtain the config function when necessary. This was
wrong in two respects:
1. It required memory allocation with disabled interrupts
(it worked, but lockdep - when enabled - reported warnings).
2. Used jiffies-based timeout, while jiffies are not running
at this stage of system shutdown (therefore a config
transaction error - if happened - would have never be reported).
Fixed by pre-allocating the config function per device
and using mdelay for timeout.
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
Nearly all of the registers in tps65090 combine control bits and
status bits. Turn off caching of all registers except the select few
that can be cached.
In order to avoid adding more duplicate #defines, we also move some
register offset definitions to the mfd driver (and resolve
inconsistent names).
Signed-off-by: Doug Anderson <dianders@chromium.org>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
- reset
- re-use qnap-poweroff driver for Synology NASs
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=j/ZI
-----END PGP SIGNATURE-----
Merge tag 'mvebu-drivers-3.15-2' of git://git.infradead.org/linux-mvebu into next/drivers
Merge "mvebu drivers for v3.15" from Jason Cooper:
pull request #1:
- mvebu mbus
- use of_find_matching_node_and_match
- rtc
- use PTR_ERR_OR_ZERO in isl12057
- work around issue in mv where date returned is 2038
- kirkwood -> mach-mvebu
- various Kconfig oneliners to allow building kirkwood in -mvebu/
pull request #2:
- reset
- re-use qnap-poweroff driver for Synology NASs
* tag 'mvebu-drivers-3.15-2' of git://git.infradead.org/linux-mvebu:
Power: Reset: Generalize qnap-poweroff to work on Synology devices.
drivers: Enable building of Kirkwood drivers for mach-mvebu
rtc: mv: reset date if after year 2038
rtc: isl12057: use PTR_ERR_OR_ZERO to fix coccinelle warnings
bus: mvebu-mbus: make use of of_find_matching_node_and_match
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The Synology NAS devices use a very similar mechanism to QNAP NAS
devices to power off. Both send a single charactor command to a PIC,
over the second serial port. However the baud rate and the command
differ. Generalize the driver to support this.
Signed-off-by: Ben Peddell <klightspeed@killerwolves.net>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Cc: Anton Vorontsov <anton@enomsg.org>
Cc: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Merge "qcom driver changes for v3.15" from Kumar Gala:
We've split Qualcomm MSM support into legacy and multiplatform. These
drivers are only relevant on the multiplatform supported SoCs so switch the
Kconfig depends to ARCH_QCOM.
* tag 'qcom-drivers-for-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/galak/linux-qcom:
gpio: msm: switch Kconfig to ARCH_QCOM depends
hwrng: msm: switch Kconfig to ARCH_QCOM depends
power: reset: msm - switch Kconfig to ARCH_QCOM depends
drm/msm: drop ARCH_MSM Kconfig depend
tty: serial: msm: Enable building msm_serial for ARCH_QCOM
We've split Qualcomm MSM support into legacy and multiplatform. The reset
driver is only relevant on the multiplatform supported SoCs so switch the
Kconfig depends to ARCH_QCOM.
Acked-by: Dmitry Eremin-Solenikov
Signed-off-by: Kumar Gala <galak@codeaurora.org>
Pull networking updates from David Miller:
1) BPF debugger and asm tool by Daniel Borkmann.
2) Speed up create/bind in AF_PACKET, also from Daniel Borkmann.
3) Correct reciprocal_divide and update users, from Hannes Frederic
Sowa and Daniel Borkmann.
4) Currently we only have a "set" operation for the hw timestamp socket
ioctl, add a "get" operation to match. From Ben Hutchings.
5) Add better trace events for debugging driver datapath problems, also
from Ben Hutchings.
6) Implement auto corking in TCP, from Eric Dumazet. Basically, if we
have a small send and a previous packet is already in the qdisc or
device queue, defer until TX completion or we get more data.
7) Allow userspace to manage ipv6 temporary addresses, from Jiri Pirko.
8) Add a qdisc bypass option for AF_PACKET sockets, from Daniel
Borkmann.
9) Share IP header compression code between Bluetooth and IEEE802154
layers, from Jukka Rissanen.
10) Fix ipv6 router reachability probing, from Jiri Benc.
11) Allow packets to be captured on macvtap devices, from Vlad Yasevich.
12) Support tunneling in GRO layer, from Jerry Chu.
13) Allow bonding to be configured fully using netlink, from Scott
Feldman.
14) Allow AF_PACKET users to obtain the VLAN TPID, just like they can
already get the TCI. From Atzm Watanabe.
15) New "Heavy Hitter" qdisc, from Terry Lam.
16) Significantly improve the IPSEC support in pktgen, from Fan Du.
17) Allow ipv4 tunnels to cache routes, just like sockets. From Tom
Herbert.
18) Add Proportional Integral Enhanced packet scheduler, from Vijay
Subramanian.
19) Allow openvswitch to mmap'd netlink, from Thomas Graf.
20) Key TCP metrics blobs also by source address, not just destination
address. From Christoph Paasch.
21) Support 10G in generic phylib. From Andy Fleming.
22) Try to short-circuit GRO flow compares using device provided RX
hash, if provided. From Tom Herbert.
The wireless and netfilter folks have been busy little bees too.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (2064 commits)
net/cxgb4: Fix referencing freed adapter
ipv6: reallocate addrconf router for ipv6 address when lo device up
fib_frontend: fix possible NULL pointer dereference
rtnetlink: remove IFLA_BOND_SLAVE definition
rtnetlink: remove check for fill_slave_info in rtnl_have_link_slave_info
qlcnic: update version to 5.3.55
qlcnic: Enhance logic to calculate msix vectors.
qlcnic: Refactor interrupt coalescing code for all adapters.
qlcnic: Update poll controller code path
qlcnic: Interrupt code cleanup
qlcnic: Enhance Tx timeout debugging.
qlcnic: Use bool for rx_mac_learn.
bonding: fix u64 division
rtnetlink: add missing IFLA_BOND_AD_INFO_UNSPEC
sfc: Use the correct maximum TX DMA ring size for SFC9100
Add Shradha Shah as the sfc driver maintainer.
net/vxlan: Share RX skb de-marking and checksum checks with ovs
tulip: cleanup by using ARRAY_SIZE()
ip_tunnel: clear IPCB in ip_tunnel_xmit() in case dst_link_failure() is called
net/cxgb4: Don't retrieve stats during recovery
...
Neither devm_usb_get_phy_by_phandle() nor devm_usb_get_phy() can
return a NULL result, so remove the useless !isp->phy check.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
On archs like S390 or um this driver cannot build nor work.
Make it depend on HAS_IOMEM to bypass build failures.
drivers/built-in.o: In function `goldfish_battery_probe':
drivers/power/goldfish_battery.c:181: undefined reference to `devm_ioremap'
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds IRQF_ONESHOT flag to max17042's irq since it uses primary
default handler. Without this flag, requesting irq will be denied with
returning error.
Signed-off-by: Jonghwa Lee <jonghwa3.lee@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Anton Vorontsov <anton@enomsg.org>
Add support for using gpio-charger IRQ as a wakeup event.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Anton Vorontsov <anton@enomsg.org>
MAX14577 chip is a multi-function device which includes MUIC, charger and
voltage regulator. The driver is located in drivers/mfd.
This patch supports battery charging control of MAX14577 chip and provides
power supply class information to userspace.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Anton Vorontsov <anton@enomsg.org>
This patch introduces device tree support to the isp1704 charger driver.
Adding support involved moving the handling of the enable GPIO from board
code into the driver.
Signed-off-by: Sebastian Reichel <sre@debian.org>
Signed-off-by: Anton Vorontsov <anton@enomsg.org>
Fixes the following warning:
drivers/power/charger-manager.c:1539:21: warning: symbol
'of_cm_parse_desc' was not declared. Should it be static?
Signed-off-by: Anton Vorontsov <anton@enomsg.org>
This adds DT support to the bq2415x driver.
Signed-off-by: Sebastian Reichel <sre@debian.org>
Reviewed-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Anton Vorontsov <anton@enomsg.org>
Add method to get power supply by device tree phandle.
Signed-off-by: Sebastian Reichel <sre@debian.org>
Reviewed-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Anton Vorontsov <anton@enomsg.org>
This patch removing set_mode_hook function from board data and replacing
it with new string variable of notifier power supply device. After this
change it is possible to add DT support because driver does not need
specific board function anymore. Only static data and name of power supply
device is required.
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Reviewed-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Anton Vorontsov <anton@enomsg.org>
ams AS3722 supports the power off functionality to turn off system.
This commit adds power off driver for ams AS3722.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Anton Vorontsov <anton@enomsg.org>
Charger-manager can parse charger_desc data from devicetree which is used
to register charger manager.
Signed-off-by: Jonghwa Lee <jonghwa3.lee@samsung.com>
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Anton Vorontsov <anton@enomsg.org>
Charger-manager driver used to check battery temperature through the
callback function passed by platform data. Unfortunatley, without that
pre-defined callback function, charger-manager can't get battery's
temperature at all. Also passing callback function through platform data
ruins DT support for charger-manager.
This patch mondifies charger-manager driver to get temperature of battery
without pre-defined callback function. Now, charger-manager can use either
of battery thermometer in fuel-gauge and ouside of battery. It uses
thermal framework interface for outer thermometer if thermal fw is
enabled. Otherwise, it tries to use fuel-gauge's through the power supply
interface.
Signed-off-by: Jonghwa Lee <jonghwa3.lee@samsung.com>
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Anton Vorontsov <anton@enomsg.org>
This patch adds a notifier chain to the power_supply, this helps drivers
in other subsystem to listen to changes in power supply subsystem.
This would help to take some actions in those drivers on changing the
power supply properties. One such scenario is to increase/decrease system
performance based on the battery capacity/voltage. Another scenario is to
adjust the h/w peak current detection voltage/current thresholds based on
battery voltage/capacity. The notifier helps drivers to listen to changes
in power_suppy susbystem without polling the power_supply properties
Signed-off-by: Jenny TC <jenny.tc@intel.com>
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Acked-by: Jenny TC <jenny.tc@intel.com>
Signed-off-by: Anton Vorontsov <anton@enomsg.org>
max17042 now uses regmap interface but does not enable config option. This
patch fixes the following build errors:
drivers/power/max17042_battery.c:661:15: error: variable ‘max17042_regmap_config’ has initializer but incomplete type
drivers/power/max17042_battery.c:662:2: error: unknown field ‘reg_bits’ specified in initializer
drivers/power/max17042_battery.c:662:2: warning: excess elements in struct initializer
drivers/power/max17042_battery.c:662:2: warning: (near initialization for ‘max17042_regmap_config’)
drivers/power/max17042_battery.c:663:2: error: unknown field ‘val_bits’ specified in initializer
drivers/power/max17042_battery.c:663:2: warning: excess elements in struct initializer
drivers/power/max17042_battery.c:663:2: warning: (near initialization for ‘max17042_regmap_config’)
drivers/power/max17042_battery.c:664:2: error: unknown field ‘val_format_endian’ specified in initializer
drivers/power/max17042_battery.c:664:23: error: ‘REGMAP_ENDIAN_NATIVE’ undeclared here (not in a function)
drivers/power/max17042_battery.c:664:2: warning: excess elements in struct initializer
drivers/power/max17042_battery.c:664:2: warning: (near initialization for ‘max17042_regmap_config’)
drivers/power/max17042_battery.c: In function ‘max17042_probe’:
drivers/power/max17042_battery.c:684:2: error: implicit declaration of function ‘devm_regmap_init_i2c’
Signed-off-by: Austin Boyle <boyle.austin@gmail.com>
Acked-by: Jonghwa Lee <jonghwa3.lee@samsung.com>
Signed-off-by: Anton Vorontsov <anton@enomsg.org>
- A new driver for TI BQ24735 Battery Chargers, courtesy of NVidia.
- Device tree bindings for TWL4030 chips.
- Random fixes and cleanups.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=rT+j
-----END PGP SIGNATURE-----
Merge tag 'for-v3.13' of git://git.infradead.org/battery-2.6
Pull battery updates from Anton Vorontsov:
"Highlights:
- A new driver for TI BQ24735 Battery Chargers, courtesy of NVidia.
- Device tree bindings for TWL4030 chips.
- Random fixes and cleanups"
* tag 'for-v3.13' of git://git.infradead.org/battery-2.6:
pm2301-charger: Remove unneeded NULL checks
twl4030_charger: Add devicetree support
power_supply: Fix documentation for TEMP_*ALERT* properties
max17042_battery: Support regmap to access device's registers
max17042_battery: Use SIMPLE_DEV_PM_OPS
charger-manager : Replace kzalloc to devm_kzalloc and remove uneccessary code
bq2415x_charger: Fix max battery regulation voltage
tps65090-charger: Use "IS_ENABLED(CONFIG_OF)" for DT code
tps65090-charger: Drop devm_free_irq of devm_ allocated irq
power_supply: Add support for bq24735 charger
pm2301-charger: Staticize pm2xxx_charger_die_therm_mngt
pm2301-charger: Check return value of regulator_enable
ab8500-charger: Remove redundant break
ab8500-charger: Check return value of regulator_enable
isp1704_charger: Fix driver to work with changes introduced in v3.5
Use this new function to make code more comprehensible, since we are
reinitialzing the completion, not initializing.
[akpm@linux-foundation.org: linux-next resyncs]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org> (personally at LCE13)
Cc: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If "pm2" were NULL we would oops printing the error message.
Fortunately, that's not possible so I have removed the NULL checks.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Anton Vorontsov <anton@enomsg.org>
This allows the charger to be enabled with devicetree, and allows the
parameters for charging the backup battery to be set.
Signed-off-by: NeilBrown <neilb@suse.de>
Acked-by: Kumar Gala <galak@codeaurora.org>
Acked-by: Grant Likely <grant.likely@linaro.org>
Signed-off-by: Anton Vorontsov <anton@enomsg.org>
This patch makes max17042 fuelguage driver uses regmap API to access its
device's registers.
Signed-off-by: Jonghwa Lee <jonghwa3.lee@samsung.com>
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Anton Vorontsov <anton@enomsg.org>
Use the SIMPLE_DEV_PM_OPS macro to declare the driver's pm_ops.
Signed-off-by: Manish Badarkhe <badarkhe.manish@gmail.com>
Signed-off-by: Anton Vorontsov <anton@enomsg.org>
Use devm function for dynamic memory allocation.
Signed-off-by: Jonghwa Lee <jonghwa3.lee@samsung.com>
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Anton Vorontsov <anton@enomsg.org>
As per the datasheets, maximum battery regulation voltage is 4440mV.
The formula is (voltage - offset) / step, so the maximum value is:
(4440 - 3500) / 20 = 47
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Thanks-to: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Anton Vorontsov <anton@enomsg.org>
Instead of "#if defined(CONFIG_OF)" use "IS_ENABLED(CONFIG_OF)" option
for DT code to avoid if-deffery in code.
Also, arranged header files in alphabetically.
Signed-off-by: Manish Badarkhe <badarkhe.manish@gmail.com>
Acked-by: Rhyland Klein <rklein@nvidia.com>
Signed-off-by: Anton Vorontsov <anton@enomsg.org>
The devm_request_irq function allocates irq that is released when a driver
detaches. Thus, there is no reason to explicitly call devm_free_irq in
probe or remove functions.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Anton Vorontsov <anton@enomsg.org>
Adds support for the bq24735 charger chipset. The bq24735 is a
high-efficiency, synchronous battery charger.
It allows control of the charging current, input current, and the charger
voltage DAC's through SMBus.
Signed-off-by: Darbha Sriharsha <dsriharsha@nvidia.com>
Signed-off-by: Rhyland Klein <rklein@nvidia.com>
Thanks-to: Stephen Warren <swarren@wwwdotorg.org>
Thanks-to: Thierry Reding <thierry.reding@gmail.com>
Thanks-to: Manish Badarkhe <badarkhe.manish@gmail.com>
Signed-off-by: Anton Vorontsov <anton@enomsg.org>
pm2xxx_charger_die_therm_mngt is used only in this file. Make it static.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Anton Vorontsov <anton@enomsg.org>
Check the return value of regulator_enable to silence the following
warning:
drivers/power/pm2301_charger.c:725:20: warning:
ignoring return value of ‘regulator_enable’, declared with
attribute warn_unused_result [-Wunused-result]
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Anton Vorontsov <anton@enomsg.org>
Each of the if-else blocks has a break statement. Remove the additional
one which is unreachable.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Anton Vorontsov <anton@enomsg.org>
Check the return value of regulator_enable to silence the following
type of warnings:
drivers/power/ab8500_charger.c:1390:20: warning: ignoring return value
of ‘regulator_enable’, declared with attribute warn_unused_result
[-Wunused-result]
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Anton Vorontsov <anton@enomsg.org>
* omap musb driver does not report USB_EVENT_ENUMERATED event anymore
* omap musb driver reporting USB_EVENT_VBUS when charger is connected
* read last event from phy->last_event (instead from ulpi register)
* do not call wall charger detection more times
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Anton Vorontsov <anton@enomsg.org>
After the last architecture switched to generic hard irqs the config
options HAVE_GENERIC_HARDIRQS & GENERIC_HARDIRQS and the related code
for !CONFIG_GENERIC_HARDIRQS can be removed.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
- APM X-Gene system reboot driver by Feng Kan and Loc Ho (APM).
- Qualcomm MSM reboot/poweroff driver by Abhimanyu Kapur (Codeaurora).
- Texas Instruments BQ24190 charger driver by Mark A. Greer (Animal Creek
Technologies).
- Texas Instruments TWL4030 MADC battery driver by Lukas Märdian and Marek
Belisko (Golden Delicious Computers). The driver is used on Freerunner
GTA04 phones.
Highlighted fixes and improvements:
- Suspend/wakeup logic improvements: power supply objects will block
system suspend until all power supply events are processed. Thanks to
Zoran Markovic (Linaro), Arve Hjonnevag and Todd Poynor (Google).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=k4RI
-----END PGP SIGNATURE-----
Merge tag 'for-v3.12' of git://git.infradead.org/battery-2.6
Pull battery/power supply driver updates from Anton Vorontsov:
"New drivers:
- APM X-Gene system reboot driver by Feng Kan and Loc Ho (APM).
- Qualcomm MSM reboot/poweroff driver by Abhimanyu Kapur (Codeaurora).
- Texas Instruments BQ24190 charger driver by Mark A. Greer (Animal
Creek Technologies).
- Texas Instruments TWL4030 MADC battery driver by Lukas Märdian and
Marek Belisko (Golden Delicious Computers). The driver is used on
Freerunner GTA04 phones.
Highlighted fixes and improvements:
- Suspend/wakeup logic improvements: power supply objects will block
system suspend until all power supply events are processed. Thanks
to Zoran Markovic (Linaro), Arve Hjonnevag and Todd Poynor (Google)"
* tag 'for-v3.12' of git://git.infradead.org/battery-2.6:
rx51_battery: Fix channel number when reading adc value
power: Add twl4030_madc battery driver.
bq24190_charger: Workaround SS definition problem on i386 builds
power_supply: Prevent suspend until power supply events are processed
vexpress-poweroff: Should depend on the required infrastructure
twl4030-charger: Fix compiler warning with regulator_enable()
rx51_battery: Replace hardcoded channels values.
bq24190_charger: Add support for TI BQ24190 Battery Charger
ab8500-charger: We print an unintended error message
max8925_power: Fix missing of_node_put
power_supply: Replace strict_strtol() with kstrtol()
power: Add APM X-Gene system reboot driver
power_supply: tosa_battery: Get rid of irq_to_gpio usage
power supply: collie_battery: Convert to use dev_pm_ops
power_supply: Make goldfish_battery depend on GOLDFISH || COMPILE_TEST
power: reset: Add msm restart support
MAINTAINERS: drivers/power: add entry for SmartReflex AVS drivers
This issue was introduced in commit 8e2747f031 "power: rx51_battery:
Replace hardcoded channels values."
Original code use channel as argument which was shifted by one in
function. After mentioned commit argument is already shifted so we need to
get index back.
Signed-off-by: Marek Belisko <marek.belisko@open-nandra.com>
Signed-off-by: Anton Vorontsov <anton@enomsg.org>
This driver is used and tested on gta04 phone. It's using twl4030_madc
(similar to rx51 existing driver). Driver also implement charging and
discharging calibration data so user can define ranges and level.
Signed-off-by: Marek Belisko <marek@goldelico.com>
Signed-off-by: Lukas Märdian <lukas@goldelico.com>
Signed-off-by: Anton Vorontsov <anton@enomsg.org>
For __i386__ builds we have:
arch/x86/include/uapi/asm/ptrace-abi.h:#define SS 16
And in the driver:
BQ24190_SYSFS_FIELD_RO(vbus_stat, SS, VBUS_STAT)
That breaks the build like this:
drivers/power/bq24190_charger.c:375:138: error: ‘BQ24190_REG_16’
undeclared here (not in a function)
drivers/power/bq24190_charger.c:375:162: error:
‘BQ24190_REG_16_THERM_STAT_MASK’ undeclared here (not in a function)
drivers/power/bq24190_charger.c:375:203: error:
‘BQ24190_REG_16_THERM_STAT_SHIFT’ undeclared here (not
in a function)
With this commit we workaround the problem by undefining 'SS'.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Anton Vorontsov <anton@enomsg.org>
This patch, originally authored by Arve Hjonnevag and Todd Poynor,
prevents the system from entering suspend mode until the power supply
plug, unplug, or any other change of state event is fully processed. This
guarantees that the screen lights up and displays the battery charging
state. The implementation uses the power supply wakeup_source object.
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Arve Hjonnevag <arve@android.com>
Cc: Todd Poynor <toddpoynor@google.com>
Cc: John Stultz <john.stultz@linaro.org>
Signed-off-by: Zoran Markovic <zoran.markovic@linaro.org>
Signed-off-by: Anton Vorontsov <anton@enomsg.org>
ARM Versatile Express reset driver requires platform-specific config
infrastructure to be present in the kernel. When VEXPRESS_CONFIG is not
selected, the build will fail like this:
drivers/built-in.o: In function `vexpress_reset_do.clone.0':
iio-trig-interrupt.c:(.text+0x1aff38): undefined reference to `__vexpress_config_func_get'
iio-trig-interrupt.c:(.text+0x1aff4c): undefined reference to `vexpress_config_write'
Added required dependency to the Kconfig entry.
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
Signed-off-by: Anton Vorontsov <anton@enomsg.org>
The return value of regulator_enable need to be checked. This patch fixes
the following warning:
drivers/power/twl4030_charger.c: In function ‘twl4030_charger_enable_usb’:
drivers/power/twl4030_charger.c:192:20: warning: ignoring return value of ‘regulator_enable’, declared with attribute warn_unused_result [-Wunused-result]
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Anton Vorontsov <anton@enomsg.org>
In twl4030_madc header exist defines for fixed channels + add rx51
specific channels and replace all hardcoded channels values.
Signed-off-by: Marek Belisko <marek.belisko@open-nandra.com>
Signed-off-by: Anton Vorontsov <anton@enomsg.org>
Add driver support for the Texas Instruments BQ24190 battery charger.
Some of the information provided by the device is about the charger and
other information is about the battery so create two power_supply objects
(one for each) and provide the appropriate information for each one.
The device has many fields that go beyond what is reasonable to report or
modify using the existing 'POWER_SUPPLY_PROP_*' properties so the driver
exports the register fields via sysfs. They are prefixed by 'f_' (for
'field') to make it easier to distinguish between a register field and a
"normal" sysfs file exported by the power_supply infrastructure.
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Anton Vorontsov <anton@enomsg.org>
There is a missing break statement here, so we print an error message that
the USB type is invalid. The original code still works fine though except
for the error message.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Anton Vorontsov <anton@enomsg.org>
Decrease np device_node refcount after we are done with the node.
Signed-off-by: Libo Chen <libo.chen@huawei.com>
Signed-off-by: Anton Vorontsov <anton@enomsg.org>
The usage of strict_strtol() is not preferred, because strict_strtol() is
obsolete. Thus, kstrtol() should be used.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Anton Vorontsov <anton@enomsg.org>
Add APM X-Gene SoC system reboot driver. This driver handles only system
reboot. System shutdown is board specific and can be handled by board
driver or GPIO based shutdown driver.
Signed-off-by: Loc Ho <lho@apm.com>
Signed-off-by: Feng Kan <fkan@apm.com>
Signed-off-by: Kumar Sankaran <ksankaran@apm.com>
Signed-off-by: Anton Vorontsov <anton@enomsg.org>
This commit fixes the following error:
linux/drivers/power/tosa_battery.c:153:2: error: implicit declaration of
function 'irq_to_gpio' [-Werror=implicit-function-declaration]
Since 9d08d5d77a, irq_to_gpio() is no longer
available but still in use by collie_battery.c. As it's just for a debug
message, just get rid of this call.
Signed-off-by: Andrea Adami <andrea.adami@gmail.com>
Signed-off-by: Anton Vorontsov <anton@enomsg.org>
Nearly all the other goldfish peripherals (mtd, keyboard, etc) have a
dependency on the main platform's GOLDFISH Kconfig item, but this one got
skipped. Even with consistency as a justification, there was initial
resistance[1] from some people to adding it however, as they wanted the
extra compile coverage.
Now, with CONFIG_COMPILE_TEST, we have the middle ground that will give
people the coverage who want it, and let those who don't want it to skip
ever seeing the option presented.
[1] https://lkml.org/lkml/2013/2/27/333
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Anton Vorontsov <anton@enomsg.org>
Add support for restart and poweroff functionality present on MSM chipsets
with the MPM2 ps-hold hardware.
Signed-off-by: Abhimanyu Kapur <abhimany@codeaurora.org>
Tested-by: Ivan T. Ivanov <iivanov@mm-sol.com>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Anton Vorontsov <anton@enomsg.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.13 (GNU/Linux)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=K+7Q
-----END PGP SIGNATURE-----
Merge tag 'for-v3.11' of git://git.infradead.org/battery-2.6
Pull battery subsystem update from Anton Vorontsov:
"Nothing exciting this time, just assorted fixes and cleanups"
* tag 'for-v3.11' of git://git.infradead.org/battery-2.6: (25 commits)
charger-manager: Fix regulator_get() return check
charger-manager: Fix a bug when it unregisters notifier block of extcon
tps65090-charger: Add dt node to power_supply
sbs-battery: Add dt to power_supply struct
power_supply: Add of_node_put to fix refcount
power_supply: Move of_node out of the #ifdef CONFIG_OF
power/reset: Make the vexpress driver optional on arm and arm64
charger-manager: Add missing newlines, fix a couple of typos, add pr_fmt
tps65090-charger: Fix AC detect
MAINTAINERS: Update email address for Anton Vorontsov
charger-manager: Ensure event is not used as format string
power_supply: Replace strict_strtoul() with kstrtoul()
generic-adc-battery: Fix checking if none of the channels are supported
power: Use platform_{get,set}_drvdata()
pm2301_charger: Return error if create_singlethread_workqueue fails
pm2301_charger: Fix NULL pointer dereference
lp8727_charger: Support the device tree feature
twl4030_charger: Remove unnecessary platform_set_drvdata()
rx51_battery: Remove unnecessary platform_set_drvdata()
jz4740-battery: Remove unnecessary platform_set_drvdata()
...
Preparing to move the parsing of reboot= to generic kernel code forces
the change in reboot_mode handling to use the enum.
[akpm@linux-foundation.org: fix arch/arm/mach-socfpga/socfpga.c]
Signed-off-by: Robin Holt <holt@sgi.com>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Russ Anderson <rja@sgi.com>
Cc: Robin Holt <holt@sgi.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Guan Xuetao <gxt@mprc.pku.edu.cn>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch fixes return value checking of regulator_get() in
charger-manager driver. The API, regulator_get(), returns ERR_PTR() when
it fails to get regulator with given name, not NULL.
Signed-off-by: Jonghwa Lee <jonghwa3.lee@samsung.com>
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Anton Vorontsov <anton@enomsg.org>
This patch prevents NULL pointer error cauesed by unregistering
unregistered exton notifier block. At the probing time of charger manager,
it tries to remove extcon notifier block when it fails to initialize them.
It has to be applied for only registered one. Otherwise, it'd make kernel
panic. To make it work right, it checks extcon_specific_cable_nb's
extcon_dev node. If extcon cable notifier block was registered
successfully, it has proper extcon_dev pointer if not so it has NULL
pointer.
Signed-off-by: Jonghwa Lee <jonghwa3.lee@samsung.com>
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Anton Vorontsov <anton@enomsg.org>
Passing in the dt node for this charger enables the logic in the core to
lookup this device, to see if it is supplying another power_supply,
through dt.
Signed-off-by: Rhyland Klein <rklein@nvidia.com>
Signed-off-by: Anton Vorontsov <anton@enomsg.org>
By passing in the dt node of this device, we enable the logic for linking
power_supplies together from dt. This is specified by adding a
"power-supplies" property with a phandle to the charger for a given
supply.
Enable this logic now for the sbs-battery driver.
Signed-off-by: Rhyland Klein <rklein@nvidia.com>
Signed-off-by: Anton Vorontsov <anton@enomsg.org>
of_parse_phandle increments the refcount for a dt node before returning
it. Add of_node_put where needed to properly decrement the refcount when
we are done using a given node.
Signed-off-by: Rhyland Klein <rklein@nvidia.com>
Signed-off-by: Anton Vorontsov <anton@enomsg.org>
The driver can be used on either arm or arm64 platforms, but
the latter doesn't have any platform-specific configuration
options, so it must be possible to manually enable the driver.
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Anton Vorontsov <anton@enomsg.org>
Use of of devm_* API for resource allocation provides benefits such
as auto handling of resource free. This reduces possibility have
memory leaks in case of wrong error handling. All direct release
calls should be removed to avoid races.
Reported-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Andrii Tseglytskyi <andrii.tseglytskyi@ti.com>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
