This patch fixes a few obvious bugs in DSP loader stuff:
- Fix possible memory leaks in the error path
- Avoid double-free calls in dma_reset()
- Properly set/unset WC bits for DMA buffers
- Add missing error status checks
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Base the DSP firmware transfer and communication timeouts on jiffy values.
Signed-off-by: Ian Minett <ian_minett@creativelabs.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch adds the HD Audio Device IDs for the Intel Wellsburg PCH
Signed-off-by: James Ralston <james.d.ralston@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A Haswell test machine showed that the invalid connection list, but
this time it has only a single pin on the codec, thus the former fixup
code doesn't work as it assumes the three pins blindly.
This patch splits the former fixup code to two parts:
- Enable eDP 1.2 for Haswell codec
- Fix the connection list of pins on Haswell codec;
the converter list is recorded dynamically in hdmi_add_cvt(), and
applied in hdmi_add_pin()
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Some Haswell machines support more than one display outputs (HDMI or DP),
but its BIOS may not enable the codec's 2nd and 3rd pin and output cvt widgets.
This patch implements a board-specific fixup for Intel Haswell Machines:
If the hidden pins are not enabled by BIOS, the driver will enable them
and call common code to update the codec tree.
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A codec may allow software to hide some unused pin/cvt widgets.
Sometimes BIOS does not enable the hidden widgets properly although they are
needed for the board. Thus the driver need to enable them as a board-specific
fixup and the whole tree will change.
This patch implements a common code for rereading codec widgets. So the fixup
code can call it after enabling the hidden widgets.
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Currently we set the max number of connections to be 32, but there
seems codec that gives longer connection lists like AD1988, and we see
errors in proc output and else. (Though, in the case of AD1988, it's
a list of all codecs connected to a single vendor widget, so this must
be something fishy, but it's still valid from the h/w design POV.)
This patch tries to remove this restriction. For efficiency, we still
use the fixed size array in the parser, but takes a dynamic array when
the size is reported to be greater than that.
Now the fixed array size is found only in patch_hdmi.c, but it should
be fine, as the codec itself can't support so many pins.
Reported-by: Raymond Yau <superquad.vortex2@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fix these two compile errors on s390 which does not have HAS_IOPORT
nor GENERIC_HARDIRQS:
sound/pci/lx6464es/lx6464es.c: In function ‘snd_lx6464es_free’:
sound/pci/lx6464es/lx6464es.c:565:2: error: implicit declaration of function ‘ioport_unmap’
sound/soc/codecs/wm8903.c: In function ‘wm8903_set_pdata_irq_trigger’:
sound/soc/codecs/wm8903.c:1954:9: error: implicit declaration of function ‘irq_get_irq_data’
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
sound/pci/hda/patch_ca0132.c: In function ‘ca0132_is_vnode_effective’:
sound/pci/hda/patch_ca0132.c:3331:15: warning: ‘nid’ may be used uninitialized in this function [-Wmaybe-uninitialized]
sound/pci/hda/patch_ca0132.c:4345:13: warning: ‘ca0132_download_dsp’ defined but not used [-Wunused-function]
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The loopback list is referred by the VIA codec driver no matter
whether CONFIG_PM is set or not, thus we need to enable it always.
Otherwise it gets compile errors.
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The wm->regs[] array has WM8766_REG_COUNT (16) elements not
WM8766_REG_RESET (31).
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
It's mostly harmless to apply it for new models even if they have no
mic mute LED (just toggling an unused GPIO pin).
Signed-off-by: Takashi Iwai <tiwai@suse.de>
These days, GUIs such as Gnome sound settings want to be able to
show the correct jack status even when no streams are currently
running. I doubt this gives any measurable difference in power,
but if it does, the "Jack Detect" control can still be used to
turn polling off.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The VT1708 has no unsol event capability, and polling is set using
the "Jack Detect" alsamixer control. In order not to create
phantom Jack controls, temporary enable jackpoll during build_controls.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
... to be less confusing for the update path.
This new kconfig will choose CONFIG_SND_HDA_DSP_LOADER, which is
basically a device-independent feature in hda_intel.c.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Commit d45e6889ee ("ALSA: hda - Provide
the proper channel mapping for generic HDMI driver") added support for
custom channel maps in the HDA HDMI driver. Due to a mistake in an
'if' condition the custom map is always used even when no such map has
been set. This causes incorrect channel mapping for multichannel audio
by default.
Pass per_pin->chmap_set to hdmi_setup_channel_mapping() as a parameter
so that it can use it for detecting if a custom map has been set instead
of checking if map is NULL (which is never the case).
Reported-by: Staffan Lindberg <pike@xbmc.org>
Signed-off-by: Anssi Hannula <anssi.hannula@iki.fi>
Cc: stable@vger.kernel.org
Signed-off-by: Takashi Iwai <tiwai@suse.de>
If the driver detects and invalid ELD, it gives an open error.
But it forgot to release the assigned pin, converter and spdif ctls
before returning.
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add new PCI ID 0x0a0c for Haswell ULT platform.
Signed-off-by: Wang Xingchao <xingchao.wang@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
For non-snoop mode, we fiddle with the page attributes of CORB/RIRB
and the position buffer, but also the ring buffers. The problem is
that the current code blindly assumes that the buffer is contiguous.
However, the ring buffers may be SG-buffers, thus a wrong vmapped
address is passed there, leading to Oops.
This patch fixes the handling for SG-buffers.
Bugzilla: https://bugzilla.novell.com/show_bug.cgi?id=800701
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Currently we use LPIB forcibly for both playback and capture for
Poulsbo and Oaktrail devices, and this seems rather problematic.
The recent fix for LPIB delay count seems working well with these
devices, so let's enable it instead.
Reported-by: Martin Weishart <martin.weishart@telosalliance.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch fixes a regression of the external mic not working on
HP Probook 4520s.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Because currently snd_printd() and snd_printdd() macros are expanded
to empty when CONFIG_SND_DEBUG=n, a compile warning like below
appears sometimes, and we had to covert it by ugly ifdefs:
sound/pci/hda/patch_sigmatel.c: In function ‘stac92hd71bxx_fixup_hp’:
sound/pci/hda/patch_sigmatel.c:2434:24: warning: unused variable ‘spec’ [-Wunused-variable]
For "fixing" these issues better, this patch replaces snd_printd() and
snd_printdd() definitions with empty inline functions instead of
macros. This should have the same effect but shut up warnings like
above.
But since we had already put ifdefs, changing to inline functions
would trigger compile errors. So, such ifdefs is removed in this
patch.
In addition, snd_pci_quirk name field is defined only when
CONFIG_SND_DEBUG_VERBOSE is set, and the reference to it in
snd_printdd() argument triggers the build errors, too. For avoiding
these errors, introduce a new macro snd_pci_quirk_name() that is
defined no matter how the debug option is set.
Reported-by: Stratos Karafotis <stratosk@semaphore.gr>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch adds a better power filter hook for powering down unused
widgets in the generic parser.
The feature is enabled by setting hda_gen_spec.power_down_unused
flag.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Put the power state synchronization at the end of the parsing of
codec. This is necessary when the power filter is changed during the
codec probe. Since the first power-up sequence is performed without
the special filter, all widgets are supposed to be ON at this point.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add a hook to struct hda_codec for filtering the target power state of
each widget when powering up/down. The current hackish EAPD check is
implemented as the default hook pointer, too.
This allows codec drivers to implement own power filter. In the
upcoming changes, the generic parser will have the better power filter
based on the active paths.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
AC_VERB_GET_POWER_STATE returns the combined bits of the actual state
and the target state. Thus, comparing the obtained value directly
with the target value can't work. The value has to be shifted and
masked properly.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The arguments to call is_active_nid() in activate_amp() were swapped,
and this resulted in the muted amp on some SPDIF output pins.
Also, the index to be passed to is_active_nid() must be idx_to_check.
Otherwise it checks the wrong connection in the case of implicit aamix
connection paths.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Using the new chained_before flag, we can correct the headphone jack
detection capability easily over the existing ALC880 6stack model
(which disables the jack detection intentionally for compatibility
reason).
Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=901846
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A Packard-Bell desktop machine gives no proper pin configuration from
BIOS. It's almost equivalent with the 6stack+fp standard config, just
take the existing fixup.
Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=901846
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Sometimes we want to call a fixup after applying other existing
fixups, but currently the fixup chain mechanism allows only the call
the others after the target fixup. This patch adds a new flag,
chained_before, to struct hda_fixup, for allowing the chained call
before the current execution.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
AD1988 family and AD1882 codecs have another mixer widget (0x21)
between the analog-loopback mixer widget (0x20) and the actual
outputs. Due to this hole, the analog-loopbacks aren't sent properly
to the output pins.
As a band-aid fix, introduce another fields holding the aamix merge
path, and activate it.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The commit [26a6cb6c: ALSA: hda - Implement a poll loop for jacks as a
module parameter] introduced the polling jack detection code, but it
also moved the call of snd_hda_jack_set_dirty_all() in the resume path
after resume/init ops call. This caused a regression when the jack
state has been changed during power-down (e.g. in the power save
mode). Since the driver doesn't probe the new jack state but keeps
using the cached value due to no dirty flag, the pin state remains
also as if the jack is still plugged.
The fix is simply moving snd_hda_jack_set_dirty_all() to the original
position.
Reported-by: Manolo Díaz <diaz.manolo@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The fixup function is called multiple times before parsing the pins,
so snd_BUG_ON() hits when loaded. Move it to the proper place in the
if block.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This is a merge of really big changes: the generic parser is heavily
enhanced for handling all cases, based on the former Realtek codec
driver code. And all codec drivers except for a few ones (CA0132,
HDMI and modem) have been converted to use the new generic driver.
Conflicts:
sound/pci/hda/patch_realtek.c
Now all AD codecs have the proper BIOS auto-parser, and we can make
it for default, finally. (AD1988 already did it because it had the
auto-parser.)
Signed-off-by: Takashi Iwai <tiwai@suse.de>
As done for patch_conexant.c, put ifdef ENABLE_AD_STATIC_QUIRKS for
preparing t odrop the static quirk codes in patch_analog.c.
The whole static quirk code can be omitted by commenting out
ENABLE_AD_STATIC_QUIRKS define now.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
AD codecs have strange implementations for choosing the SPDIF-output
mux source: the digital audio out widget may take the sources from
multiple connections, where 0x01 indicates it's a PCM while others
point ADCs. It's obviously invalid in the HD-audio spec POV, but it's
somehow convincing, too. And, to make things more complex, AD1988A
and AD1882 have deeper connection routes that aren't expressed
correctly.
In this patch, the SPDIF mux control is implemented in two ways:
- For easier one like AD1981, AD1983, AD1884 and AD1984, where the
SPDIF audio out widget takes just two or three sources, we can
simply implement via the normal input_mux and connection verb
calls.
- For the complex routes like AD1988A (but not AD1988B) or AD1882, we
prepare "faked" paths represented statically, and switch the paths
using these static ones, instead of parsing the routes from the
widget tree.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Since both snd_hda_codec_flush_amp_cache() and
snd_hda_codec_flush_cmd_cache() are called usually at the same time,
we can simply combine them to a single function,
snd_hda_codec_flush_cache().
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The capture volume put callback may call the node selection change,
and its actual call won't be triggered unless flushed. In general,
we always need to call both snd_hda_codec_flush_amp_cache() and
snd_hda_codec_flush_cmd_cache() at the same place...
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Both the HP auto-mute and the independent HP mode conflict with each
other. Make HP auto-mute disabled (only for the affected HP jack)
during the driver is in HP independent mode.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
It'd be better to give another name to the secondary (alt) analog PCM
stream, which is dedicated for the independent HP out and extra
inputs.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The aamix NIDs are also missing for AD codecs. All AD codecs seem to
have a (more or less) working aamix widget.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
IDT codecs have analog-loopback mixer widgets, but we haven't cared
about it, so far. Let's set them. This will avoid also possible
wrong routes for the input paths.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch eventually fixes two issues:
- Handle the case where the primary output is a headphone and can have
independent HP mode;
so far we checked only the case where the headphone is the secondary
output.
- Fix the conflict of HP independent mode and aamix mode;
when switched to aamix mode, the DAC might be also switched to
another widget shared with other outputs. Then even if we disable
the DAC for the original output, it doesn't change -- because the
active route is from another (shared) DAC to HP pin through aamix.
So, in such a case, we have to prohibit the switch to aamix for HP
routes.
This fixes issues appearing on VT codecs.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Many codecs provide routes to multiple output pins through an aamix
widget, but most of them do it only from a single DAC. However, the
current generic parser checks only the aamix paths from the original
(directly bound) DACs through aamix NID, and miss the path:
primary DAC -> aamix -> target out pin
This patch adds a more check for the routes like the above.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When a patch couldn't be resolved in try_assign_dacs() although the
target DAC is expected, we forgot to add a proper badness value but
continued.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Since fill_and_eval_dacs() may be called repeatedly with different
configurations, setting pinctls at each time there isn't optimal.
We can set it better only once after deciding the output configuration
in parse_output_paths().
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Print the information of outputs in a bit more details and concisely
in a single place instead of printing the path at each time when
detected.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Conexant CX20551 codec has a mixer in NID 0x19 and a few outputs have
to take the input through this widget.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Looking through the whole definitions, some fields have inappropriate
array sizes, especially about the capture. The array assigned to each
input (pin) should have HDA_MAX_NUM_INPUTS entries while the array
assigned to each ADC should have AUTO_CFG_MAX_INS entries.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The patch "ALSA: hda - fix wrong adc_idx in generic parser" fixed the
adc_idx for the capture volume and capture switch controls. But also
modified the adc_idx retrieval for the capture source controls
wrongly. As multiple capture source controls are created in a single
shot with counts > 1, the id.index doesn't contain the real value.
The real index has to be taken via snd_ctl_get_ioffidx() as in the
original code.
This patch reverts the fixes partially to recover from the
regression.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
If there's one each of HDMI and SPDIF, we should not add an index
on the one that comes second.
[slight code refactoring by tiwai]
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Just stumbled over this one while reading the code.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
I found a codec configuration which had six inputs, so the max of
five was not appropriate.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Some BIOS version of FSC Lifebook S7110 laptop seems to give a wrong
default pin config for NID 0x15, which confuses the parser. Give a
fixup to correct the value.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Although I commented that boost volumes would be added only for
line-in and mic pins in the source code, the actual code excludes but
for mic-in. Fix it to accept the line-ins, too.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Two hooks in hda_gen_spec, cap_sync_hook and capture_switch_hook, play
very similar roles. The only differences are that the former is
called more often (e.g. at init or switching capsrc) while the latter
can take an on/off argument.
As a more generic implementation, consolidate these two hooks, and
pass snd_ctl_elem_value pointer as the second argument. If the
secondary argument is non-NULL, it can take the on/off value, so the
caller handles it like the former capture_switch_hook. If it's NULL,
it's called in the init or capsrc switch case.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When a standard capture switch without multiple binding is used, the
call for capture_switch_hook isn't called properly. Replace the put
ops to add the hook call in that case.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This machine also has the "HP_Mute_LED_0_A" string in DMI information.
Cc: <stable@vger.kernel.org>
BugLink: https://bugs.launchpad.net/bugs/1096789
Tested-by: Tammy Yang <tammy.yang@canonical.com>
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In the current generic parser code, we look for the (mic) boost
controls only on input pins. But many codecs assign the boost volume
to a widget connected to each input pin instead of the input amp of
the pin itself.
In this patch, the parser tries to look through more widgets connected
to the pin and find a boost amp.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When an amp in the activation path is associated with mixer controls,
activate_amp() tries to skip the initialization. It's good, but only
if the mixer really initializes both mute and volume. Otherwise,
either the mute of the volume is left uninitialized.
This patch adds this missing check and properly initialize the
partially controlled amps in an activation path.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
There are a few places creating the labels and indices of kctls for
each input pin in the current generic parser code. This is redundant
and makes harder to maintain. Let's create the labels and indices at
once and keep them in hda_gen_spec.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Since the imux table entries can be a subset of autocfg.input table,
the indices of these aren't always same. For passing the proper index
value of autocfg.input at creating input ctl labels (via
snd_hda_autocfg_input_label()), keep the corresponding autocfg.input
idx value in the index field of each imux item, which isn't used in
the generic driver.
Also, this makes easier to check the invalid imux pin for stereo mix.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Finally we reached here. All codecs driver (except for CA0132, which
has really device-specific requirements) have been converted to use
the generic parser.
This patch appears bigger than others since it also involves with the
code shuffling, but mostly the cut-off of parser codes and adapt to
the generic parser flags. Most of fixup codecs haven't been changed
but just removed a few unnecessary codes.
The only missing stuff is the SPDIF mux control. It'll be added again
later.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
* test/hda-gen-parser:
ALSA: hda - Improve naming rule for primary output
ALSA: hda - Add PCM capture hook to hda_gen_spec
ALSA: hda - Record all detected ADCs in hda_gen_spec
ALSA: hda - Move vmaster TLV parsing to snd_hda_gen_parse_auto_config()
ALSA: hda - Add input jack mode enum controls to generic parser
ALSA: hda - Give more comments to hda_gen_spec flags
ALSA: hda - Add suppress_auto_mute flag to hda_gen_spec
ALSA: hda - Record the current speaker / LO mute status in hda_gen_spec
ALSA: hda - Properly call automute/switch hooks at init
When the volume or mute control of the primary output is shared with
other (headphone or speaker) outputs, we shouldn't name it as a
specific output type but rather name it with the channel name or a
generic name like "PCM".
Also, this check should be performed individually for the volume and
the mute controls because some codecs may have shared volumes but
separate mute controls.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Since the generic parser reduces the ADC list, copy the list of the
all detected ADCs and keep it.
This list can be later referred by the codec driver for finer power
controls.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add vmaster_tlv[] to hda_gen_spec and store the suggested TLV data
in snd_hda_gen_parse_auto_config(). This allows the codec driver to
correct the TLV data (e.g. mute capability) before actually creating
vmaster instance.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Just like the jack mode enum ctls for output jacks, add the support
for similar enum ctls for input pins to control the bias Vref.
The new controls will be added when spec->add_in_jack_modes is set
either by the codec driver or by a hint string.
Note that ground and 100% vrefs are excluded from the list for
simplicity, currently. We may add a new flag to allow them, too.
But I guess it's easier to put a value override in the pinfix in such
a case.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
- spec->hp_detect has to be overridden in HDA_FIXUP_ACT_PARSE, not in
PRE_PARSE.
- Remove err == 0 check but return directly -EINVAL from
stac92xx_parse_auto_config()
- Set spec->default_polarity for 92HD71bxx
- Some code shuffles
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A new flag to skip the auto-mute handling in the generic parser, just
like suppress_auto_mic flag. It has to be set before calling
snd_hda_gen_parse_auto_config().
Signed-off-by: Takashi Iwai <tiwai@suse.de>
* test/hda-gen-parser:
ALSA: hda - Make sure fill_all_dac_nids is called for digital only codecs
ALSA: hda - force different capture controls if amp caps differ
ALSA: hda - do not add non-existing Mic boost controls
ALSA: hda - initialize channel counts correctly
ALSA: hda - fix wrong adc_idx in generic parser
ALSA: hda - Check array bounds in get_input_path
ALSA: hda - Add prefer_hp_amp flag to hda_gen_spec
ALSA: hda - fix OOPS in hda_mark_cmd_cache_dirty
ALSA: hda - Check pincap while parsing the configuration
Otherwise no PCM will be built for codecs without analog I/O.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Otherwise setting the capture volume for amps will be weird and
inconsistent (it will try to set values outside the range of the
second amp based on capabilities of the first amp).
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
If the input node does not have any volume capable input amp,
don't add such a control.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Even a single DAC can output two channels, so the channel count
is twice the number of DACs.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
We use knew->index for adc_idx when we create "Capture Volume" and
"Capture Switch", so use the same to retrieve adc_idx.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
sound/pci/hda/patch_ca0132.c:387:19: sparse: symbol 'ca0132_voicefx' was not declared. Should it be static?
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
With HDSP_TOGGLE_SETTING in place, these functions are no longer
required. Removing them makes the code DRY and considerably shorter.
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
HDSP_TOGGLE_SETTING and its corresponding functions allow to change
settings in the control register. Instead of using the specialised
functions, use the generic code to make the code DRY.
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The driver contains multiple similar functions that change only a single
bit in the control register, only the bit position varies.
This patch implements a generic function to toggle a certain bit
position that will be used to replace the old code.
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The current iobox detection code reportedly fails for various users, so
simply do what the Win32 driver does instead.
Patch originally by Karl Grill <kgrill@chello.at> and then modified to
comply with kernel coding guidelines + current HEAD.
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add a new flag to indicate whether HP amp is turned on as default for
speaker or line-outs, and enable this for ALC260 codec, as many
machines with this codec require the HP amp even for speakers.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
sound/pci/hda/patch_ca0132.c: In function ‘ca0132_effects_set’:
sound/pci/hda/patch_ca0132.c:3391:2: warning: too many arguments for
format [-Wformat-extra-args]
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Spotted by smatch,
sound/pci/hda/patch_ca0132.c:1950 dspxfr_image() error: potential
null dereference 'dma_engine'. (kzalloc returns null)
sound/pci/hda/patch_ca0132.c:1950 dspxfr_image() error: we
previously assumed 'dma_engine' could be null (see line 1857)
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
sound/pci/hda/patch_ca0132.c:1781 dspxfr_one_seg() info: why not
propagate 'status' from dsp_dma_stop() instead of (-5)?
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The recent update of ca0132 driver replaced the pinctl setup to the
direct write via snd_hda_codec_write() again. This should be covered
by snd_hda_set_pin_ctl() to be safer.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This reverts commit c3b4eea262.
Since the recent firmware loader code supports caching at S3/S4 by
itself, we don't have to handle f/w caching in the driver.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Handle a potential dma_engine alloc error and fix the possible use of an
uninitialized status variable in dspxfr_one_seg(). Also correct the initial
sampling rate for Mic 1.
Update the module description.
Signed-off-by: Ian Minett <ian_minett@creativelabs.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch adds the controls used for tuning the DSP effects.
Signed-off-by: Ian Minett <ian_minett@creativelabs.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch adds the unsolicited response handler for incoming DSP responses and
jack detection reporting, and routines for reading the incoming DSP response.
Signed-off-by: Ian Minett <ian_minett@creativelabs.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Remove the playback PCM open callback.
PCM stream setup and cleanup functions are added for use by PCM callbacks.
Delay stream cleanup if effects are on, to allow time for any effects tail to
finish.
Add the analog capture PCM callbacks.
Change the max channels of analog playback to 6.
Add two new PCMs: AMic2 and What-U-Hear.
Signed-off-by: Ian Minett <ian_minett@creativelabs.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch adds the kcontrols for the DSP effects, playback and recording
source selection.
ca0132_is_vnode_effective() checks whether virtual node settings have
taken effect.
The control change helpers ca0132_pe_switch_set(), ca0132_voicefx_set()
and ca0132_cvoice_switch_set() are added to toggle playback / capture
DSP effects, ca0132_voicefx_info(), _get() and _put() are added for
input path DSP effect value access. The volume helpers are updated to
volume_info(), _get() and _set() to use the virtual nodes.
The redundant headphone and speaker switches and ct_extension function
are removed.
Signed-off-by: Ian Minett <ian_minett@creativelabs.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch adds the framework to set effect parameters: ca0132_effects_set()
and ca0132_setup_defaults() are general functions for parameter setting and
initializing to default values. dspio_set_param() and dspio_set_uint_param()
are lower-level fns to simplify setting individual DSP parameters via an
SCP buffer transfer to the firmware.
The CA0132 chip parameter init code is added in ca0132_init_params().
In chipio_[write,read]_data(), the current chip address is auto-incremented
if no error has occurred.
ca0132_select_out() selects the current output. If autodetect is enabled,
use headphones (if jack detected) or speakers (if no jack).
ca0132_select_mic() selects the current mic in. If autodetect is enabled,
use exterior mic (if jack detected) or built-in mic (if no jack).
Init digital mic and switch between dmic and amic with ca0132_init_dmic(),
ca0132_set_dmic(). amic2 is initialized in ca0132_init_analog_mic2().
Finally, add verb tables for configuring DSP firmware.
Signed-off-by: Ian Minett <ian_minett@creativelabs.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch adds definitions and structs used for configuring DSP effects,
virtual nodes, effect tuning controls, and mixer control helpers.
The effect structs are also initialized.
Signed-off-by: Ian Minett <ian_minett@creativelabs.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When "alsactl restore" is performed on HDMI codecs, it tries to
restore the channel map value since the channel map controls are
writable. But hdmi_chmap_ctl_put() returns -EBADFD when no PCM stream
is assigned yet, and this results in an error message from alsactl.
Although the error is harmless, it's certainly ugly and can be
regarded as a regression.
As a workaround, this patch changes the return code in such a case to
be zero for making others happy. (A slight excuse is: when the chmap
is changed through the proper alsa-lib API, the PCM status is checked
there anyway, so we don't have to be too strict in the kernel side.)
Cc: <stable@vger.kernel.org> [v3.7+]
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Instead of checking the codec SSID in find_mute_led_cfg() for HP Mini
110, set the proper spec->default_polairty in the fixup table.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The PCI vendor ID check in find_mute_led_cfg() is now superfluous
because the function is called in the fixup table entries of HP
machines.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Finally all codecs in patch_sigmatel.c have been converted to use the
standard fixup helpers. This change also includes trivial cleanups
like the call of common setup for GPIO LED or the removal of unused
function.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This one is rather a simple conversion. The fixups for Dell machines
are implemented by fixup functions in the end.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This time, the only intrusive changes are for HP machines.
As the mute LED fixup and the bass speaker switch are required only
for HP machines, we can move these checks into the fixup entries; the
former is applied generically to all HP machines while the latter for
only certain models.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Sometimes (or rather often) BIOS sets the pin default configurations
obviously wrongly. Looking through these failures, one common pattern
is to enable some dead pins that are usually marked as speaker pins.
In such a case, we can skip them if the pins don't have the output
capability.
In this patch, add a check for the valid pin cap bit for each parsed
pin, and filter out when it's invalid.
The fix was originally suggested by Raymond Yau.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This conversion is a bit tricky. Since STAC927x may take two
different volume-knob initialization values depending on the model, a
new flag, spec->volknob_init, is introduced to indicate whether it's
the standard volume-knob initialization or not.
Also, Dell BIOS model is now directly mapped onto the fixup table
instead of parsing in the function. This resulted in a new model ref,
STAC_927X_DELL_BIOS_SPDIF, which is a chained entry.
Also, for reducing the fixups, virtual entries like
STAC_927X_DELL_DMIC and STAC_D965_VERBS are introduced.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Rather straightforward conversion, except for ones for Intel Mac.
As Intel Mac have only unique codec SSIDs, we need to remap the fixup
again for the codec SSID and call the new fixup there.
Also, we can reduce model enums like STAC_MACMINI, which are model
aliases for backward compatibility, since they can be pointed directly
via hda_model_fixup table.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Yet another step forward. As all features for VIA codecs have been
implemented in the generic driver, we can move on to migrate the VIA
codec parser, too.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch adds the support for the generic auto-parser to AD codec
driver. For AD1988, the old code is replaced simply with the new
generic parser. For other codecs, new model "auto" is added and
directed to use the generic parser.
No fixup codes have been implemented yet as of now. Eventually we'd
replace each static quirk with the generic parser + fixup.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Just shuffle the codes and add ifdefs for testing to drop the static
quirk codes from patch_conexant.c.
By commenting out ENABLE_CXT_STATIC_QUIRKS define at the beginning of
the file, you can disable the whole static codes.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This time, the target is Cirrus codec. Its parser is a subset of
generic parser, so we can migrate fully with it now.
The only tricky part is the handling of SPDIF automute.
Cirrus driver sets the SPDIF out plug over the headphone. As a
workaround, set spec->gen.master_mute for toggling the headphone (and
other) mute.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
CA0110 codec is a fairly straightforward hardware implementation,
and we can use the generic parser almost as is.
Just set spec->multi_cap_vol flag to follow the current behavior.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Replace the old parser code for C-Media auto-parser with the latest
generic parser. For compatibility reason, the static bindings are
still left, but they could be cleaned up in future.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The pincfgs, init_verbs and hints set by sysfs or patch might be
changed dynamically on the fly, thus we need to protect it.
Add a simple protection via a mutex.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
As David Henningsson recently suggested, some HP laptops use an unused
mic pin for controlling a mute LED, and this information is provided
via DMI string "HP_Mute_LED_X_Y" string. This patch adds the generic
support for such cases, as we've already done in patch_sigmatel.c.
This is applied generically to all devices with ID 0x103c.
But as we don't know whether the device 103c:1586 really contains
HP_Mute_LED_X_Y DMI string, still keep the static setup for this
device using the mic2 pin 0x19.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Some fixups such as setting the flags influencing on the parser
behavior should be applied before actually parsing the tree.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Try to recover from the regression: set the HP amp for the speaker and
add the hp jack mode enum as default.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add the enum controls for changing the headphone amp bits of output
jacks, such as "Headphone Jack Mode". This feature isn't enabled as
default, so far, unless spec->add_out_jack_modes flag is set.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When a multi-io jack is switched to another direction, call the
automute and autoswitch update functions, as this jack won't be used
as the headphone or the mic jack that may turn off others.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add a new fixup type, HDA_FIXUP_PINCTLS, for overriding the pinctl
values of the given pins. It takes the same array of struct pintbl
like HDA_FIXUP_PINS, but each entry contains the pinctl value instead
of the pin default config value.
This patch also replaces the corresponding codes in patch_realtek.c.
Without this change, the direct call of verbs may be overridden again
by the later call of pinctl restoration by the driver.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Now the whole codebase has been changed from the earlier kernels, it
makes little sense to keep these aliases. Simply replace with the
official names.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When a jack is retasked as a different direction (e.g. a mic jack is
used as a CLFE output), such a jack shouldn't be counted as the target
for the automatic jack switching. Skip the automute or the autoswitch
when the current pinctl direction is different from what we suppose.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Use the new pin target accessors for managing the current pinctl
values in the generic parser. The pinctl values of all active pins
are once determined at the initialization phase, and stored via
snd_hda_codec_set_pin_target(). This will be referred again in the
codec init or resume phase to set the actual pinctl.
This value is kept while the auto-mute. When a line-out or a speaker
pin is muted by auto-mute, the driver simply disables the pin, but it
doesn't touch the cached pinctl target value. Upon unmute, this value
is used to restore the original pinctl in return.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Check more strictly about the validity of pinctl values in
snd_hda_set_pin_ctl() and correct the wrong bits automatically.
Also provide the helper function to correct pinctl bits to codec
drivers.
This automatically fixes the invalid pinctl writes that are found in
a few Realtek fixups for NID 0x0f amp like ASUS A6Rp.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
We already have the list of whole pin widgets and there is an unused
space in the list; let's use it for caching the current pinctl value.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When a DAC is reassigned from surrounds to front or ADCs are reduced
due to incomplete imux, we clear the path indices but the path
instances remain as is. Since the paths might be still referred
through the whole path list parsing (e.g. is_active_nid()), we should
clear these path instances as well.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Since some codecs can choose the aamix as a capture source, we should
support it as well. When spec->add_stereo_mix_input flag is set, the
parser checks the availability of aamix as the input source, and adds
the paths automatically when possible.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In the current parser code, the input_paths[] may become inconsistent
when some of detected ADCs are dropped due to incomplete inputs, since
the driver rearranges only adc_nids[] but doesn't touch input_paths[].
This patch fixes the issue, and also it optimizes the reachability
checks by simply referring to the parsed input_paths[] instead of
calling is_reachable() again for each connection.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Instead of handling special cases in the caller side, give a proper
name string "Headphone Mic" from hda_get_autocfg_input_label() when
the headhpone jack pin is specified as an input.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The capture paths shouldn't contain the analog loopback mixer.
Pass a proper argument to exclude the aamix NID.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add a new flag spec->suppress_mic_auto_switch for codecs that don't
support unsol events properly like VT1708.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When the default config value shows the connection AC_JACK_PORT_BOTH,
it's better to handle it as a speaker pin. This makes the behavior
consistent in snd_hda_get_pin_label() and snd_hda_parse_pin_defcfg().
There are only few old machines showing this attribute, and all of
them are actually fixed speaker pins, as far as I know.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This commit modifies the definition of snd_hda_parse_nid_path()
slightly, now with_aa_mix argument is changed to anchor_nid, so that
it can handle any NID generically as an anchor point to include or
exclude.
The with_aa_mix field in struct nid_path is removed again by this
change.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The multi-io channels can vary not only from 1 to 6 but also may vary
from 6 to 8 or such. At the same time, there are more speaker pins
available than the primary output pins. So, we need three variables
to check: the minimum channel counts for primary outputs, the current
channel counts for primary outputs, and the minimum channel counts for
all outputs.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Instead of looking through paths with the dac -> pin connection at
each time, just pass the already parsed path index to
assign_out_path_ctls(). This simplifies the code a bit.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The path indices must be reset at each evaluation of DAC assignment.
Otherwise the badness value will be wrongly calculated and mixers may
be inconsistently assigned.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Let is_jack_detectable() return true when the jack polling is enabled
for the codec. VT1708 uses the polling explicitly so we need to allow
it.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The new hook which is called at each PCM playback ops.
It can be used to control the codec-specific power-saving feature in
each codec driver.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The bind-volume workaround was introduced for simplifying the mixer
abstraction in the case where one or more pins of multiple outputs
lack of individual volume controls. This was essentially the case
like Acer Aspire 5935, which has 5.1 speakers and 5.1 (multi-io)
jacks although there are 5 DACs, so some of them must share a DAC.
However, the recent code rewrite changed the DAC assignment policy to
share with the same channel instead of binding to the front, thus
binding the volumes for all channels makes little sense now, rather
it's confusing. So in this patch, the ugly workaround is finally
dropped and simply create the volume control corresponding to the
parsed path position.
For dual headphones or 2.1 speakers with a shared volume control, it's
anyway bound to the same DAC if needed, so this change shouldn't bring
any practical difference.
And, as a good bonus, we can cut off the whole code handling the bind
volume elements.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When 5.1 or more multiple speakers with found but not enough DACs are
available, it's better to bind such pins to the DACs of the primary
outputs with the same channels rather than binding to the first DAC
(i.e. the front channel). For the cases with two speaker pins, it's
rather regarded as front + bass combination, thus it's more practical
to still bind to the front, though.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
... like "Speaker Surround Playback Switch".
This fix had been already applied to patch_conexant.c but was
forgotten in other places, then migrated to hda_generic.c.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
For codecs that have individual routes going through a loopback mixer
(like VIA codecs), we need to provide an explicit switch to choose
whether the output goes through mixer or directly from DAC.
This patch adds the check for such paths and creates "Loopback Mixing"
enum control when available.
It won't influence on codecs like Realtek or others where the loopback
mixer is connected independently from the primary output routes.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The output paths including aamix should be parsed only for the first
output. The surround paths including aamix must be wrong, since it
would mix all streams, i.e. all channels would be mixed into a single
and multiplexed again.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Call the path activation for the digital input pin properly, not only
setting the pin control. Also add spec->digin_path for keeping the
path index.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Instead of search for the path with the certain route at each time,
keep the path index for each output and loopback, and just use it when
referred.
In this implementation, the path index number begins with one, not
zero (although I've been writing in C over decades). It's just to
make the check for uninitialized values easier.
So far, the input paths aren't handled with indices yet, but still
picked up via snd_hda_get_nid_path() at each time.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When speakers are chosen as the the primary output during evaluation,
we did some tricks to assign the possible multi-io jacks with a
certain offset value to multi_out dacs. This was a workaround for the
case with multiple speakers like Acer Aspire. But this is quite ugly
at the same time and the resultant code is hard to understand. More
badly, it works wrongly for 2.1 speakers like Apple iMac91.
In this patch, instead of fiddling with the offset to multi_out dacs,
simply add a certain badness number if headphone(s) + multi-ios are
possible. This simplify the code a bit, and it's more robust.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
If the requested path has been already added, return the existing path
instance instead of adding a duplicated instance.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When the paths are created in map_singles(), we don't have to
re-create new paths in try_assign_dacs(). Just evaluate the badness
and skip to the next item.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Set path->active flag at the path creation time and let the paths
initialized according to the current path->active state in
set_output_and_unmute(). This allows to modify the active flag of
some output paths dynamically, e.g. switching the front output route
with or without aamix like patch_via.c.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
activate_amp() in the generic parser checks whether the given NID is
included in any active paths and skips it if found. This was a
workaround for avoiding disabling the widgets in the active paths when
one path is disabled, thus it shouldn't be applied to the case for
path activation. Due to this wrong check, some analog loopback paths
haven't been initialized correctly.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Manage the connection list cache using linked lists instead of
snd_array, and revive snd_hda_get_conn_list() again, so that we don't
have to keep the expanded values locally.
This will reduce the stack usage by recursive call of
snd_hda_get_conn_index() or parse_nid_path() of the generic parser.
The list management doesn't include any mutex protection, thus the
caller needs to take care of race appropriately.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Yet another broken hardware workaround: there are hardware indicating
the inverted jack detection bit result.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add the new flag, codec->inv_eapd, indicating that the EAPD
implementation is inverted.
There are always broken hardware in the world.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Similar like the implementation in patch_analog.c and patch_via.c,
the generic parser can provide the independent HP PCM stream now.
It's enabled when spec->indep_hp is set by the caller while parsing.
Currently no dynamic PCM switching as in patch_via.c is implemented
yet. The control returns -EBUSY when the value is changed during PCM
operations.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Allow the path including the loopback mixer widget in the primary
output channel as an alternative in the generic codec parser.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add a better debug print code to show the new assigned paths in
generic parser. It appears only with CONFIG_SND_DEBUG_VERBOSE=y.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
It's never used in the generic parser. It was there from the old
Realtek code, which has been dropped quite ago, too.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When a PCM name string is generated from the chip name, it might
become strange like "CX20549 (Venice) Analog". In this patch, the
parser tries to drop the invalid words like "(Venice)" in the PCM name
string. Also, when the name string is given beforehand by the caller,
respect it and use it as is.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
There were some old codes that look not stable enough, which was
derived from the old Realtek code. The initialization for primary
output in init_multi_out() needs to consider the case of shared DAC.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
For preliminary works to migrate the generic parser for Conexant
codecs: the same function is ported to hda_generic.c.
But now it looks through the jack detect table so that it can cover
better.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add a flag to indicate whether the vmaster mute hook enum is exposed
or not. Conexant codecs may want not to expose the control depending
on the model.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Old codecs like AD1986A tend to have long paths as they were just made
to be the way like AC97. The current max depth 5 can be too short for
such devices.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The access to a cache array element could be invalid outside the
mutex, so copy locally for the later references.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The dirty entry has to be checked at the beginning in the loop, not in
the inner loop for channels. This caused a regression that the right
channel isn't properly written.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The bound capture volume and switch controls use the cached amp
updates, but it's missing the flushing at the end.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The inverted dmic fix overwrites the right channel amp value, but it
would work only when the amp values have been already actually
written. Put snd_hda_codec_resume_amp() before the amp write for
flushing caches.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add an overflow check of CORB in HD-audio controller and codec drivers
so that flood of sequential writes would work properly.
In the controller side, add a check of CORB read-pointer to make
returning -EAGAIN when it's full. Meanwhile in the codec side, when
-EAGAIN error is received, it retries the write after flushing the
pending verbs (calling get_response() essentially does it).
Signed-off-by: Takashi Iwai <tiwai@suse.de>
These functions are supposed to be called at finishing the cached
sequential writes, so clear the flag properly for lazy developers who
often forget details.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When verbs or amps are actually written to the hardware, we can clear
dirty flag so that the later snd_hda_codec_resume_*() calls can skip
these verbs / amps.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The commit [2e9bf24: ALSA: hda_codec: Check for invalid zero
connections] trims the whole connection list when an invalid value is
reported by the hardware. But some codecs (at least AD1986A) may give
a zero NID in the middle of the connection list, so dropping the whole
list isn't good for such cases.
In this patch, as a workaround, allow a single zero NID in the read
connection list. If it hits zero twice, it's handled as an error, so
that we can avoid "too many connections" errors.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In general we prefer "Capture Source" to "Input Source".
The latter was chosen in many places just because "Capture Source"
label doesn't work well with the current alsa-lib mixer abstraction
when multiple instances are present. But when we know that there is a
single input-source element, we can safely choose "Capture Source"
label.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The next migration step is to use the common code in generic driver
for Realtek driver. This is no drastic change and there should be no
real functional changes, as the generic parser code comes from Realtek
driver originally.
As Realtek driver requires the generic parser code, it needs a
reverse-selection of CONFIG_SND_HDA_GENERIC kconfig.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
These handlers are supposed to be called externally from the codec
drivers once when they need to handle own jack events.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When no controls are assigned in the parser (e.g. no analog path),
spec->kctls.list is still NULL. We need to check it before passing to
snd_hda_add_new_ctls().
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In some cases, we want to manipulate the auto_pin_cfg table before
passing to snd_hda_gen_parse_auto_config() (e.g. Realtek SSID check
code fiddles with the headphone pin). Also passing ignore_pins just
for snd_hda_parse_pin_defcfg() isn't good.
In this patch, snd_hda_gen_parse_auto_config() is changed to receive
the auto_pin_cfg table to be parsed. The passed auto_pin_cfg table
must have been initialized (typically by calling
snd_hda_gen_parse_auto_config()) beforehand by the caller.
Also together with this change, spec->parse_flags is also removed.
Since this was referred only at the place calling
snd_hda_parse_pin_defcfg(), no longer needed to be kept in spec.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Finally the whole generic parser code in Realtek driver is moved into
hda_generic.c so that it can be used for generic codec driver.
The old dumb generic driver is replaced. Yay.
The future plan is to adapt this generic parser for other codecs,
i.e. the codec driver calls the exported functions in generic driver
but adds some codec-specific fixes and setups.
As of this commit, the complete driver code is still duplicated in
Realtek codec driver. The big code reduction will come from now on.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch extends the capability of the auto-mic feature.
Instead of limiting the automatic input-source selection only to the
mics (internal, external and dock mics), allow it for generic inputs,
e.g. switching between the rear line-in and the front mic.
The logic is to check the attribute and location of input pins, and
enable the automatic selection feature only if all such pins are in
different locations (e.g. internal, front, rear, etc) and line-in or
mic pins. That is, if multiple input pins are assigned to a single
location, the feature isn't enabled because we don't know the
priority.
(You may wonder why this restriction doesn't exist for the headphone
automute. The reason is that the output case is different from the
input: the input source is an exclusive selection while the output
can be multiplexed.)
Note that, for avoiding regressions, the line-in auto switching
feature isn't activated as default. It has to be set explicitly via
spec->line_in_auto_switch flag in a fixup code.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Put INPUT_PIN_ATTR_FRONT after INPUT_PIN_ATTR_REAR, and define
INPUT_PIN_ATTR_LAST to point to the last element.
This is a preliminary work for cleaning up Realtek auto-mic parser.
In the auto-mic implementation, the front panel is preferred over the
rear panel. By arranging the attr definitions like in this commit, we
can simply use sort() for figuring out the priority order.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The previous commit passed an utterly wrong value for checking the
split inv dmic pin. This patch fixes it and also tries to remove
inv_dmic_split_idx field.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Since the fixup code is used commonly, it's worth to move it to the
common place, struct hda_codec, instead of keeping in hda_gen_spec.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
To make the parser more generic, a few codes to handle the inverted
stereo dmic in a way Conexant parser does is added in this patch.
The caller should set spec->inv_dmic_split flag appropriately.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
So far we create only "Capture Volume" and "Capture Switch" controls
for binding all possible amps, but we'd prefer creating individual
capture volume and switch controls per input in some cases
(e.g. conexant parser does it).
Add a new flag, spec->multi_cap_vol, to follow that policy.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Merge a few functions that have been split due to historical reasons
to single functions. Splitting too much (and placing too far away)
actually worsens the readability.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
There are a few more cases where we can assign "Master" mixer element
safely, e.g. when a single DAC is used in the whole output paths.
Also, when vmaster hook is present, avoid "Master" but assign "PCM"
instead. Otherwise vmaster hook won't work properly.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
... so that the fixup just needs to set the hook function in
FIXUP_ACT_PROBE. This will make easier to port for other codecs,
too.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add a new field to indicate the possible pin NID for alternative vref
setup for the shared hp/mic. Although 0x18 is valid for all Realtek
codecs, it'll be different on other vendor's codecs.
Also, drop the sanity check in update_shared_mic_hp() since the
reference pin is set explicitly in the caller side.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Make the function more generic for both input and output directions,
and returns the assigned path pointer. The argument order is changed
to follow the standard (from, to) way.
Now this new function is used for analog input and loopback path
parser codes, too.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The amps will be initialized via activate_path(), thus it's
superfluous to set in alc_auto_init_analog_input().
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Remove some fields from struct alc_spec, and clean up the usage.
Namely,
- spec->input_mux becomes a single element, private_imux[] is removed
- spec->adc_nids becomes an array by itself, and private_adc_nids[]
gets removed, too
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Now we reached to the final big piece of parser rewrite: the input
paths. While the old parser code assumes the more-or-less direct and
similar connections from input pin to ADC, the new code handles the
complete input paths. The capture source is switched by simple calls
of activate_path() function.
The parsing of capture volume and capture switches is, however, not
fully generalized. It assumes that amps are available in the vicinity
of ADCs (in three depth). This isn't perfect but it should cover all
codecs I know of.
Also, this commit removes some NID mapping of capture-related controls
temporarily for simplicity. It'll be restored in later commits.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Now we have a complete list of loopback paths, thus we can initialize
the paths more completely based on it, instead of assuming a direct
connection from pin to mixer.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Don't forget to take boost volumes into account in the managed path
list. Since it's an additional volume, we need to extend the ctls[]
array.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The paths used for multi-io haven't been initialized properly, so
far. It's usually no big matter because the pins are set to input as
default, but it's still cleaner to initialize the paths properly.
Now with the path active/inactive check, we can do it easily.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The pin widget has only a single amp value for the input even if it
has multiple "sources". Handle the situation in activate_path().
Signed-off-by: Takashi Iwai <tiwai@suse.de>
alc_auto_is_dac_reachable() can be replaced fully with
is_reachable_path(). The only difference is the order of arguments.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
... and rewrite the initialization of output paths as a generic
function that is applicable for both i/o directions.
The new flag, active, is introduced to each nid_path entry. This
indicates whether the given path is active, and it's used for checking
whether a certain widget can be turned off or changed when a path is
no longer used or newly enabled.
It's still used only in the output paths. More wider adaption for
input and loopback paths will be achieved in the later patch.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
We are using only AUTOMUTE_MODE_PIN in patch_realtek.c and all others
have been already dropped. Let's remove the old superfluous codes.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The new function snd_hda_codec_amp_init() (and the stereo variant)
initializes the amp value only once at the first access. If the amp
was already initialized or updated, this won't do anything more.
It's useful for initializing the input amps that are in the part of
the path but never used.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
For optimizing the verb executions, a new mechanism to cache the verbs
and amp update commands is introduced. With the new "write to cache
and flush" way, you can reduce the same verbs that have been written
multiple times.
When codec->cached_write flag is set, the further
snd_hda_codec_write_cache() and snd_hda_codec_amp_stereo() calls will
be performed only on the command or amp cache table, but not sent to
the hardware yet. Once after you call all commands and update amps,
call snd_hda_codec_resume_amp() and snd_hda_codec_resume_cache().
Then all cached writes and amp updates will be written to the
hardware, and the dirty flags are cleared.
In this implementation, the existing cache table is reused, so
actually no big code change is seen here. Each cache entry has a new
dirty flag now (so the cache key is now reduced to 31bit).
As a good side-effect by this change, snd_hda_codec_resume_*() will no
longer execute verbs that have been already issued during the resume
phase by checking the dirty flags.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When initializing the output paths, we assumed the input amps have
almost two inputs blindly. It's not only generic but even incorrect
for some codecs like ALC268 & co. Also, the same assumption (two
sources) exists for the bind input-amp controls.
This patch changes the codes in these places to handle the input
connections in a more generic way.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
For handling the analog-loopback paths more generically, check the amp
capabilities of the aa-mixer widget, and create only the appropriate
mixer elements.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Improve the parser of analog loopback paths and handle in a more
generic way. The following changes are included in this patch:
- Instead of assuming direct connections between pins and
the mixer widget, track the whole path between them. This fixes
some missing connections like ALC660.
- Introduce the path list for loopback paths like input and output
path lists. Currently it's not used for any real purposes, yet.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Just like the output paths, parse the whole paths for inputs as well
and store in a path list. For that purpose, rewrite the output parser
code to be generically usable.
The input path list is not referred at all in this patch. It'll be
used to replace the fixed adc/capsrc array in later patches for more
flexible input path selections.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
So far, idx[i] and multi[i] indicate the attribute of the widget
path[i - 1]. This was just for simplifying the code in
__parse_output_path(), but this is rather confusing for later use.
It's more natural if both idx[i] and multi[i] point to the same widget
of path[i]. This patch changes to that way.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Simplify the output path initialization using the existing path
information instead of assuming the topology specific to Realtek
codecs. This is also implicitly a fix for some amp values on output
pins where the old parser missed (e.g. ALC260 output pins).
The same function alc_auto_set_output_and_unmute() can be used now for
the multi-io activation, since the output selection means nothing but
activating the given output path.
And, finally at this stage, we can get rid of alc_go_down_to_selector()
and other functions that are codec really specifically to Realtek
codecs.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
So far, Realtek codec driver evaluates the NIDs for volume and mute
controls twice, once while parsing the DACs and evaluating the
assignment, and another while creating the mixer elements. This is
utterly redundant and even fragile, as it's assuming that the ctl
element evaluation is identical between both parsing DACs and creating
mixer elements.
This patch simplifies the code flow by doing the volume / mute
controls evaluation only once while parsing the DACs. The patch ended
up in larger changes than expected because of some cleanups became
mandatory.
As a gratis bonus, this patch also fixes some cases where the stereo
channels are used wrongly for mono amps.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The mono widget is always connected to the left channel, thus the left
channel amp value also should be referred for mono widgets instead of
the right channel.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
As we parse the output paths more precisely now, we can use this path
list for parsing the widgets for volume and mute mixer controls.
The spec->vol_ctls[] and sw_ctls[] bitmasks are replaced with the
ctls[] in each output path instance.
Interestingly, this move alone automagically fixes some bugs that the
conflicting volume or mute NIDs weren't properly detected.
Also, by parsing the whole path, there are more chances to get a free
widget for volume/mute controls.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add the output path parser to Realtek codec driver as we already have
in patch_via.c. The nid_path struct represents the complete output
path from a DAC to a pin. The alc_spec contains an array of these
paths, and a new path is added at each time when a new DAC is
assigned.
So far, this path list is used only in limited codes: namely in this
patch, only alc_is_dac_already_used() checks the list instead of dac
arrays in all possible outputs. In the later development, the path
list will be referred from more places, such as the mixer control
assignment / check, the mute/unmute of active routes, etc.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In the probing phase, create a list of all available DACs in the codec
and use it for checking the single DAC connections.
This list will be used in more other places in the later commits, too.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Use the helper function snd_hda_get_conn_index() instead of open
codes. This also improves the detection of some routes to DAC on
ALC260 (although the difference doesn't influence on the end
results of the mapping).
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Added the support for a new codec ALC284, which is compatible with
ALC269. Also add more codec variants to handle the SSID check
properly.
Signed-off-by: Kailang Yang <kailang@realtek.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Use correct bitmask for AES32 cards to determine wordclock lock state,
add missing bitmask for sync check and make output of the corresponding
control and /proc coherent.
Signed-off-by: Andre Schramm <andre.schramm@iosono-sound.com>
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Change the power_save_controller option to bint from bool so that user
can override the runtime PM capability bit and force to enable or
disable the runtime PM.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This reverts commit 697c373e34.
The original patch was meant to remove clicking, but in fact caused even
more clicking instead.
Thanks to c4pp4 for doing most of the work with this bug.
BugLink: https://bugs.launchpad.net/bugs/886975
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
We've got a few bug reports that the runtime D3 results in the dead
HD-audio controller. It seems that the problem is in a deeper level
than the sound driver itself, so as a temporal solution, disable the
feature for these controllers again.
Reported-and-tested-by: Vincent Blut <vincent.debian@free.fr>
Reported-and-tested-by: Maurizio Avogadro <mavoga@gmail.com>
Cc: <stable@vger.kernel.org> [v3.7]
Signed-off-by: Takashi Iwai <tiwai@suse.de>
It seems useful, and power states are required for AFG nodes,
so I see no reason not to print it. As a bonus, also print the
AFG nid.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The mute LED is in this case connected to the Mic1 VREF.
The machine also exposes the following string in BIOS:
"HP_Mute_LED_0_A", so if more machines are coming, it probably
makes sense to try to do something more generic, like for the
IDT codec.
Cc: stable@vger.kernel.org
BugLink: https://bugs.launchpad.net/bugs/1096789
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
vortex_wt_setdsout performs bit-negation on the bit position (wt&0x1f)
rather than on the resulting bitmask. This code is never actually
invoked (vortex_wt_setdsout is always called with en=1), so this does
not currently cause any problem, and this patch is simply cleanup.
Signed-off-by: Nickolai Zeldovich <nickolai@csail.mit.edu>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The vmaster hook sends 1 for enabled/unmuted and 0 for disabled/muted,
but "Mute-LED Mode" being "On" refers to the LED being on, not the
volume being on.
Therefore "On" and "Off" should be switched.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This update contains overall only driver-specific fixes.
Slightly large LOC are seen in usb-audio driver for a couple of new
device quirks and cs42l71 ASoC driver for enhanced features.
The others are a few small (regression) fixes HD-audio, and yet other
small / trival ASoC fixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iQIcBAABAgAGBQJQ0thSAAoJEGwxgFQ9KSmk/i8P+wcdjCcp5FdfZ5YP2h9siEw5
7KJPwwk9eTa0PVB5olgabxSh6L5P+rM69OGiXnHSKF8RwsuZDRp/5pPcaoUVRzH/
6uibGozfLApeLBuBAJZ96eJhRIigysoSrm5W4FQeNVAbwK67zpIjP/xGwKa0+qfO
vsK/BtSn+nVsmFpgOfO6vXZ7gKBlfKGXHYdyFVXzHEhGYSHLdf1IDxnCapIXlh78
0nXHD2FHgKlSM6y/S6W7wiUwyNqbgmnZHwh29iIyes1CrX0wVyvtos3qgwJHukrU
WVY87E1TDxD6HLAWTUxqeOIvNyucSarUZ+kvtYg0i31gmRCY8QNXqYVp1wBybqVd
Uwbwe4qWwSxXhXluodFsizNwcH9T+KA3IM4B5u6yCT1pFY759pCh/KpLoNfD+maL
6atnBU6lvtTCMxoeSyJFSdAjdOQJUpylQ9TyQaI/PIr6jrEMVC2ki/i3UX+YpQGo
oWJj5x8Nl58MUv7GhYGTo7vfm3ZqaUbxN/YugbCeVkrcV0McJNycvddotplD4iTd
pqfep1fVpefW9X4pJnvsys2neo7R8e8a87Qg2CfVGXQ91ijevPCf+YAh4EmHShsT
vwNcOP/gZ+qQp/bY40SigMj5SZtZ/ZQxT47yPo6OLI4FyhyD+WK4l1AAEK5B1uPA
odsIcQg2F6/RjzkDSsSl
=JoY5
-----END PGP SIGNATURE-----
Merge tag 'sound-3.8' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"This update contains overall only driver-specific fixes. Slightly
large LOC are seen in usb-audio driver for a couple of new device
quirks and cs42l71 ASoC driver for enhanced features. The others are
a few small (regression) fixes HD-audio, and yet other small / trival
ASoC fixes."
* tag 'sound-3.8' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: usb-audio: Support for Digidesign Mbox 2 USB sound card:
ALSA: HDA: Fix sound resume hang
ALSA: hda - bug fix for invalid connection list of Haswell HDMI codec pins
ALSA: hda - Fix the wrong pincaps set in ALC861VD dallas/hp fixup
ALSA: hda - Set codec->single_adc_amp flag for Realtek codecs
ASoC: atmel-ssc: change disable to disable in dts node
ASoC: Prevent pop_wait overwrite
ALSA: usb-audio: ignore-quirk for HP Wireless Audio
ALSA: hda - Always turn on pins for HDMI/DP
ALSA: hda - Fix pin configuration of HP Pavilion dv7
ASoC: core: Fix splitting of log messages
ASoC: cs42l73: Change VSPIN/VSPOUT to VSPINOUT
ASoC: cs42l73: Add DAPM events for power down.
ASoC: cs42l73: Add DMIC's as DAPM inputs.
ASoC: sigmadsp: Fix endianness conversion issue
ASoC: tpa6130a2: Use devm_* APIs
Resuming a switcheroo'd HDA controller hangs since the completion
is one-shot (thus works the first time). Fix by using completions
that explictly need rearming, so remain fired before.
Signed-off-by: Daniel J Blueman <daniel@quora.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Haswell HDMI codec pins may report invalid connection list entries, which
will cause failure to play audio via HDMI or Display Port.
So this patch adds fixup for Haswell to workaround this hardware issue:
enable DP1.2 mode and override the pins' connection list entries with proper
value.
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com>
Signed-off-by: Xingchao Wang <xingchao.wang@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The workaround to force VREF50 for dallas/hp model with ALC861VD
was introduced in commit 8fdcb6fe42,
but it contained wrong pincap override bits.
This patch fixes to exclude VREF80 pincap bit correctly.
Cc: <stable@vger.kernel.org> [v3.2+]
Signed-off-by: Takashi Iwai <tiwai@suse.de>
It turned out that Realtek codecs (ALC260, etc) with input amps in
audio-input widgets don't handle the multiple individual input amps.
Thus we need to set codec->single_adc_amp flag for them in general.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
We've seen the broken HDMI *video* output on some machines with GM965,
and the debugging session pointed that the culprit is the disabled
audio output pins. Toggling these pins dynamically on demand caused
flickering of HDMI TV.
This patch changes the behavior to keep the pin ON constantly.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=51421
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Pull trivial branch from Jiri Kosina:
"Usual stuff -- comment/printk typo fixes, documentation updates, dead
code elimination."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (39 commits)
HOWTO: fix double words typo
x86 mtrr: fix comment typo in mtrr_bp_init
propagate name change to comments in kernel source
doc: Update the name of profiling based on sysfs
treewide: Fix typos in various drivers
treewide: Fix typos in various Kconfig
wireless: mwifiex: Fix typo in wireless/mwifiex driver
messages: i2o: Fix typo in messages/i2o
scripts/kernel-doc: check that non-void fcts describe their return value
Kernel-doc: Convention: Use a "Return" section to describe return values
radeon: Fix typo and copy/paste error in comments
doc: Remove unnecessary declarations from Documentation/accounting/getdelays.c
various: Fix spelling of "asynchronous" in comments.
Fix misspellings of "whether" in comments.
eisa: Fix spelling of "asynchronous".
various: Fix spelling of "registered" in comments.
doc: fix quite a few typos within Documentation
target: iscsi: fix comment typos in target/iscsi drivers
treewide: fix typo of "suport" in various comments and Kconfig
treewide: fix typo of "suppport" in various comments
...
Fix the quirk entry for HP Pavilion dv7 in order to make the bass
speaker working.
Reported-and-tested-by: Tomas Pospisek <tpo2@sourcepole.ch>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The runtime_idle callback is the right place to check the suspend
capability, but currently we do it wrongly in the runtime_suspend
callback. This leads to a kernel error message like:
pci_pm_runtime_suspend(): azx_runtime_suspend+0x0/0x50 [snd_hda_intel] returns -11
and the runtime PM core would even repeat the attempts.
Reported-and-tested-by: Borislav Petkov <bp@alien8.de>
Cc: <stable@vger.kernel.org> [v3.7]
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Acer Aspire One 522 has the infamous digital mic unit that needs the
phase inversion fixup for stereo.
Bugzilla: https://bugzilla.novell.com/show_bug.cgi?id=715737
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The HD-audio driver artificially calls the suspend and the resume code
path in the VGA switcheroo state changes. When a machine goes to
suspend, it tries to suspend the device again, and it stalls at
snd_power_wait().
This patch adds checks whether the devices were already in (forced)
suspend in PM callbacks for avoiding the doubly suspend.
Reported-by: Daniel J Blueman <daniel@quora.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When the HD-audio controller is disabled (e.g. via vga switcheroo) but
the driver is still accessing it, it spews floods of "spurious
response" kernel messages. It's because CORB/RIRB WP reads 0xff, and
the driver tries to fill up until this number.
This patch changes the CORB/RIRB WP reads to word instead of byte, and
add the check of the read value. If it's 0xffff, the controller is
supposed to be disabled, so the further action will be skipped.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Reducing the time on HDA link reset can help to reduce the driver loading
time. So we replace msleep with usleep_range to get more accurate time
control and change the value to a smaller one. And a 100ms timeout is set
for both entering and exiting the link reset.
Signed-off-by: Xingchao Wang <xingchao.wang@intel.com>
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add support for new codec VT1808, which is similiar with VT1705CF.
Signed-off-by: Lydia Wang <lydiawang@viatech.com.cn>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add support for new codec VT1705CF.
When power on/off Audio output converter of VT1705CF, the stream tag
will be cleared. But driver caches the value. So when power on Audio
output converter, the update_conv_power_state() will restore the saved
stream tag of it.
Signed-off-by: Lydia Wang <lydiawang@viatech.com.cn>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Remove the leftover __devinit* in comments.
They have been commented out because they couldn't fit with __dev*
although they should have matched.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Since __devinit* have been removed completely, DELAYED_INIT*_MARK in
hda_intel.c became NOP. Let's rip them off.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
CONFIG_HOTPLUG is going away as an option. As result the __dev*
markings will be going away.
Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Acked-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
CONFIG_HOTPLUG is going away as an option. As result the __dev*
markings will be going away.
Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Acked-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
CONFIG_HOTPLUG is going away as an option. As result the __dev*
markings will be going away.
Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: Thibaut Varene <T-Bone@parisc-linux.org>
Cc: linux-parisc@vger.kernel.org
Signed-off-by: Takashi Iwai <tiwai@suse.de>
CONFIG_HOTPLUG is going away as an option. As result the __dev*
markings will be going away.
Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When printing, use a prefix of the PCI domain, bus, device and function
as in other drivers, to differentiate multiple devices.
Important for reporting and debugging. A future step is to tidy this up with
dev_printk et al.
v2: Move conversion specifier into call site, preventing build issues
v3: Refactor for Takashi's for-next branch
Signed-off-by: Daniel J Blueman <daniel@quora.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The recent fix for vga switcheroo race in commit 128960a9 opened yet
another race. At the time the audio driver starts probing, user may
turn off D-GPU off. But at this moment, the audio driver still
doesn't register the vga switcheroo client, thus the switching isn't
notified. Then the hardware gets off out of sudden, resulting in
invalid reads and lots of "spurious response" error messages.
For solving this situation, the following changes have been done in
this patch:
- Move again vga switcheroo registration to the very early stage of
the probing; this also requires to set pci drvdata properly before
registration
- Introduce the completion to synchronize the driver probe at vga
switcheroo callbacks; this assures that the whole probing finished
before executing the callbacks
Reported-by: Daniel J Blueman <daniel@quora.org>
Tested-by: Daniel J Blueman <daniel@quora.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
With HDSPM_TOGGLE_SETTING in place, these functions are no longer
required. Removing them makes the code DRY and considerably shorter.
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
HDSPM_TOGGLE_SETTING and its corresponding functions allow to change
settings in the control register. Instead of using the specialised
functions, use the generic code to make the code DRY.
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The driver contains at least six similar functions that change only a
single bit in the control register, only the bit position varies.
This patch implements a generic function to toggle a certain bit
position that will be used to replace the old code.
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The current Realtek driver reconfigures the max PCM channels
dynamically according to the value of Channel Mode enum if the
multi-io retasking is available. It works fine for multi-io pins.
But when multiple speaker pins are available, the channels of speakers
also have to obey to the channel mode, which isn't nice.
(That is, when you select "2ch" in Channel Mode so that the line-in
and mic jack behave as input, you can't play surrounds properly from
the built-in speaker.)
This patch fixes the problem by taking the channel number for multiple
speakers into account in the channel-mode setup code.
Also it fixes the wrongly set up max_channels value in the case of
multi-io extension.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Very quiet release for ASoC really:
- Standardisation of the logging.
- DT and dmaengine support for Atmel.
- Support for Wolfson ADSP cores.
- New drivers for Freescale/iVeia P1022 and Maxim MAX98090.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=2irt
-----END PGP SIGNATURE-----
Merge tag 'asoc-3.8' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-next
ASoC: Updates for v3.8
Very quiet release for ASoC really:
- Standardisation of the logging.
- DT and dmaengine support for Atmel.
- Support for Wolfson ADSP cores.
- New drivers for Freescale/iVeia P1022 and Maxim MAX98090.
The same type of code is being used in multiple places in various
codec drivers, so put it as a core library.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This is a preliminary patch for introducing a protection to access
races of snd_array instances. Call snd_array_init() appropriately
at the initialization time and don't call it twice.
Also the allocations of codec-spec structs are cleaned up by helper
functions in patch_sigmatel.c and patch_analog.c.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Tidy up and condense chipio_write_address|addx() functions.
Improve dspio_write_wait() to use jiffies for timeout calc.
Signed-off-by: Ian Minett <ian_minett@creativelabs.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add comments and descriptions to functions.
Bump dsp_free_ports() to below dsp_allocate_ports_format() to group the
alloc functions together for commenting.
Signed-off-by: Ian Minett <ian_minett@creativelabs.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch adds the code needed to fetch the DSP binary image from the local
firmware install location and transfer it over to the chip using the new DSP
loader bus ops.
Actual DSP effect controls, parameters and mixers are to be included later.
- Add calls to new DSP loader system to transfer firmware to the hardware.
- Add chip read/write routines, DSP I/O, SCP packet format helper functions and
transfer DMA management.
- Add guard around DSP download to ensure loader config switch is enabled.
The general scheme for downloading the DSP is as follows:
1) If DSP firmware loader is enabled, ca0132_download_dsp() is called
to start the process.
2) Driver requests DSP image using request_firmware().
3) Driver sets up the streaming DMA for DSP image download
with dspload_image() and dspxfr_image(), which in turn calls the DSP loader
op snd_hda_codec_load_dsp_prepare() to ready the system.
4) DSP image will consist of 1 or more segments, each transferred in sequence
by a call to dspxfr_one_seg() and snd_hda_codec_load_dsp_trigger().
5) Once complete, the loader state is cleaned up with
snd_hda_codec_load_dsp_cleanup().
Signed-off-by: Ian Minett <ian_minett@creativelabs.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Pass DMA buffer pointers in calls to setup_bdle().
Add DSP loader callback routines to controller.
Add new DSP loader switch to Kconfig to turn off DSP firmware.
Signed-off-by: Ian Minett <ian_minett@creativelabs.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
I forgot this again... codec->in_pm is in #ifdef CONFIG_PM
Reported-by: Markus Trippelsdorf <markus@trippelsdorf.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The internal mic on MBP81 gives only the right channel, and the left
channel is static. Add a verb to fix the ADC2 channel mode to expand
mono right to stereo.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=50781
Signed-off-by: Takashi Iwai <tiwai@suse.de>
We forgot to apply the fixup verbs in cs_init().
But adding the fixup verbs will break mbp101 fixup that has been fixed
recently again, since the mbp101 fixup contains the wrong verbs to
override. So these bogus verbs must be removed, too.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
As the recent firmware code tries to reread and cache the firmware by
itself, it's even better to keep the struct firmware data instead of
keeping a local copy. Also, it makes little sense to disable the fw
loader for this driver, so added the explicit dependency, too.
Last, but not least, allocate the firmware data loaded via ioctl in
vmalloc'ed buffer instead, as the firmware size isn't that small.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The new firmware code tries to re-read the formerly read firmware
files before suspend. Thus it's wiser to keep the "patch" firmware in
the driver for avoiding this unnecessary re-reading.
Of course, this will consume a bit of memory for unused stuff, but
the patch fw is supposed to be fairly small, so it's more benefit in
the end.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
It makes no longer sense to keep the old hwdep user-space firmware
loading, which has been deprecated since ages ago.
Just add a hard dependency on CONFIG_FW_LOADER and drop the useless
code.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Since we keep the pin default config values anyway internally, we
don't have to set the values in the codec. This patch removes the
code writing the pincfg values.
As a gratis bonus, we can remove also the code restoring the original
pincfg values at PM resume or module free. This will give us more
benefit, as it can reduce the unnecessary power-up of codecs.
This won't change the driver functionality. The only difference would
be that the codec proc file will show the original pincfg values
instead of the actually referred values. The actually referred values
can be determined from sysfs *_pin_configs files.
(Also hda-emu was updated to follow this change.)
Signed-off-by: Takashi Iwai <tiwai@suse.de>
