Move size and mask definitions into efx.h; calculate page orders in falcon.c.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While we're at it, use type suffixes of 'd', 'q' and 'o', consistent
with register type names.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Siena is still based on the Falcon hardware architecture and will
share many of these definitions, so replace falcon_hwdefs.h with
regs.h.
The new definitions have been generated according to a naming
convention which incorporates the type and revision information.
Update the code accordingly.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since there are now separate blocks of code to set the thresholds for
each NIC type, it is no longer useful to include them in the NIC type
description.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These macros are not extensible to more than two NIC types without
repetition of register definitions, and they are only used to deal
with a few fields in RX_CFG_REG and global events which moved between
Falcon rev A1 and B0.
Therefore:
- Move RX_CFG_REG initialisation into its own function which tests the
NIC revision just once
- Explicitly test the NIC revision when checking the RX_RECOVERY flag in
global events
- Merge definitions of RX_XOFF_MAC_EN flag, which did not move
- Remove the macro definitions
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Siena will require entirely different board code.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
At this point (ri_tasklet()), RTNL or dev_base_lock are not held,
we must use dev_get_by_index() instead of __dev_get_by_index()
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
fixes the following build failure:
CC drivers/net/au1000_eth.o
/drivers/net/au1000_eth.c: In function 'au1000_set_settings':
/drivers/net/au1000_eth.c:623: error: implicit declaration of function 'capable'
/drivers/net/au1000_eth.c:623: error: 'CAP_NET_ADMIN' undeclared (first use in this function)
/drivers/net/au1000_eth.c:623: error: (Each undeclared identifier is reported only once
/drivers/net/au1000_eth.c:623: error: for each function it appears in.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Improve the reporting of myri10ge port type in ethtool,
and update for new boards.
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: Andrew Gallatin <gallatin@myri.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit b6b39e8f3f (tcp: Try to catch MSG_PEEK bug) added a printk()
to the WARN_ON() that's in tcp.c. This patch changes this combination
to WARN(); the advantage of WARN() is that the printk message shows up
inside the message, so that kerneloops.org will collect the message.
In addition, this gets rid of an extra if() statement.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PHY on 82577/82578 parts needs a soft reset when transitioning to Sx
state in order for the PHY write which disables gigabit speed to take
effect. Gigabit speed must be disabled in order for the PHY writes to
registers on page 800 (the wakeup control registers) to work as expected
otherwise the system might not wake via WoL.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commits 27fbc7d 'mdio: Expose pause frame advertising flags to ethtool'
and c634263 'sfc: 10Xpress: Initialise pause advertising flags'
added to our reported advertising flags.
efx_mdio_set_settings() requires that all advertising flags are
also present in the supported flags, so make sure that is true.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There's a circular locking dependency:
---> isdn_net_get_locked_lp
--->lock &nd->queue_lock
--->lock &nd->queue->xmit_lock
.....................
---->unlock &nd->queue_lock
---> isdn_net_writebuf_skb (called with &nd->queue->xmit_lock locked)
---->isdn_net_inc_frame_cnt
---->isdn_net_device_busy
----> lock &nd->queue_lock
This will trigger lockdep warnings:
=======================================================
[ INFO: possible circular locking dependency detected ]
2.6.32-rc4-testing #7
-------------------------------------------------------
ipppd/28379 is trying to acquire lock:
(&netdev->queue_lock){......}, at: [<e62ad0fd>] isdn_net_device_busy+0x2c/0x74 [isdn]
but task is already holding lock:
(&netdev->local->xmit_lock){+.....}, at: [<e62aefc2>] isdn_net_write_super+0x3f/0x6e [isdn]
which lock already depends on the new lock.
.......
We don't need to lock nd->queue->xmit_lock to protect single
isdn_net_lp_busy(). This can fix above lockdep warnings.
Reported-and-tested-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: Xiaotian Feng <xtfeng@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Old code assumed board config version in the flash to be 1.
When this will get changed by tools, driver just refuses to
attach. This is unnecessary since driver does not have to
parse board config structure directly (maintained by firmware).
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clear NX_RESETING bit in netxen_tx_timeout_task() so that
the firmware watchdog task can catch need_reset request
from tx timeout.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Avoid resetting subsys ID in i2c block. Also remove duplicate
check for address tranlsation error.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
rtnl_getlink() & rtnl_setlink() run with RTNL held, we can use
__dev_get_by_index() and __dev_get_by_name() variants and avoid
dev_hold()/dev_put()
Adds to rtnl_getlink() the capability to find a device by its name,
not only by its index.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In ks8851_set_rx_mode() the case handling IFF_MULTICAST was also setting
the RXCR1_AE bit by accident. This meant that all unicast frames where
being accepted by the device. Remove RXCR1_AE from this case.
Note, RXCR1_AE was also masking a problem with setting the MAC address
properly, so needs to be applied after fixing the MAC write order.
Fixes a bug reported by Doong, Ping of Micrel. This version of the
patch avoids setting RXCR1_ME for all cases.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MAC address register was being written in the wrong order, so add
a new address macro to convert mac-address byte to register address and
a ks8851_wrreg8() function to write each byte without having to worry
about any difficult byte swapping.
Fixes a bug reported by Doong, Ping of Micrel.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Issue a full soft reset at probe time.
This was reported by Doong Ping of Micrel, but no explanation of why this
is necessary or what bug it is fixing. Add it as it does not seem to hurt
the current driver and ensures that the device is in a known state when we
start setting it up.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
For connected sockets, the first run of dev_pick_tx saves the
calculated txq in sk_tx_queue_mapping. This is not saved if
either the device has a queue select or the socket is not
connected. Next iterations of dev_pick_tx uses the cached value
of sk_tx_queue_mapping.
Signed-off-by: Krishna Kumar <krkumar2@in.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
dst_negative_advice() should check for changed dst and reset
sk_tx_queue_mapping accordingly. Pass sock to the callers of
dst_negative_advice.
(sk_reset_txq is defined just for use by dst_negative_advice. The
only way I could find to get around this is to move dst_negative_()
from dst.h to dst.c, include sock.h in dst.c, etc)
Signed-off-by: Krishna Kumar <krkumar2@in.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IPv6: Reset sk_tx_queue_mapping when dst_cache is reset. Use existing
macro to do the work.
Signed-off-by: Krishna Kumar <krkumar2@in.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce sk_tx_queue_mapping; and functions that set, test and
get this value. Reset sk_tx_queue_mapping to -1 whenever the dst
cache is set/reset, and in socket alloc. Setting txq to -1 and
using valid txq=<0 to n-1> allows the tx path to use the value
of sk_tx_queue_mapping directly instead of subtracting 1 on every
tx.
Signed-off-by: Krishna Kumar <krkumar2@in.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
fec_enet_init is called by both fec_probe and fec_resume, so it
shouldn't be marked as __init.
Signed-off-by: Steven King <sfking@fdwdc.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 9e337b0f (net: annotate inet_timewait_sock bitfields)
added 4/8 bytes in struct inet_timewait_sock.
Fix this by declaring tw_ipv6_offset in the 'flags' bitfield
The 14 bits hole is named tw_pad to make it cleary apparent.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Arnaldo Carvalho de Melo <acme@ghostprotocols.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
It can help being able to filter packets on their queue_mapping.
If filter performance is not good, we could add a "numqueue" field
in struct packet_type, so that netif_nit_deliver() and other functions
can directly ignore packets with not expected queue number.
Lets experiment this simple filter extension first.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We hold RTNL, we can use __dev_get_by_index() instead of dev_get_by_index()
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While doing multiple captures, I found af_packet was dirtying cache line
containing its prot_hook.
This slow down machines where several cpus are necessary to handle capture
traffic, as each prot_hook is traversed for each packet coming in or out
the host.
This patches moves "struct packet_type prot_hook" to the end of
packet_sock, and uses a ____cacheline_aligned_in_smp to make sure
this remains shared by all cpus.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch tries to print out more information when we hit the
MSG_PEEK bug in tcp_recvmsg. It's been around since at least
2005 and it's about time that we finally fix it.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch makes the private functions alloc_can_skb() and
alloc_can_err_skb() of the at91_can driver public and adapts all
drivers to use these. While making the patch I realized, that
the skb's are *not* setup consistently. It's now done as shown
below:
skb->protocol = htons(ETH_P_CAN);
skb->pkt_type = PACKET_BROADCAST;
skb->ip_summed = CHECKSUM_UNNECESSARY;
*cf = (struct can_frame *)skb_put(skb, sizeof(struct can_frame));
memset(*cf, 0, sizeof(struct can_frame));
The frame is zeroed out to avoid uninitialized data to be passed to
user space. Some drivers or library code did not set "pkt_type" or
"ip_summed". Also, "__constant_htons()" should not be used for
runtime invocations, as pointed out by David Miller.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use symbols instead of magic constants while checking PMTU discovery
setsockopt.
Remove redundant test in ip_rt_frag_needed() (done by caller).
Signed-off-by: John Dykstra <john.dykstra1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
i2400m-sdio requires iwmc3200top for its operation
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Acked-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
iwmc3200wifi requires iwmc3200top for its operation
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Acked-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds Intel Wireless MultiCom 3200 top driver.
IWMC3200 is 4Wireless Com CHIP (GPS/BT/WiFi/WiMAX).
Top driver is responsible for device initialization and firmware download.
Firmware handled by top is responsible for top itself and
as well as bluetooth and GPS coms. (Wifi and WiMax provide their own firmware)
In addition top driver is used to retrieve firmware logs
and supports other debugging features
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow bpf to set a filter to drop packets that dont
match a specific mark
Signed-off-by: Jamal Hadi Salim <hadi@cyberus.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change RX large buffer size based on MTU. If pages are larger
than the MTU the page is divided up into multiple chunks and passed to
the hardware. When pages are smaller than MTU each RX buffer can
contain be comprised of up to 2 pages.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ipv4/ipv6 setsockopt(IP_MULTICAST_IF) have dubious __dev_get_by_index() calls.
This function should be called only with RTNL or dev_base_lock held, or reader
could see a corrupt hash chain and eventually enter an endless loop.
Fix is to call dev_get_by_index()/dev_put().
If this happens to be performance critical, we could define a new dev_exist_by_index()
function to avoid touching dev refcount.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
