Add the low-level device commands and definitions used for QP max-rate limiting.
This is done through the following elements:
- read rate-limit device caps in QUERY_DEV_CAP: number of different
rates and the min/max rates in Kbs/Mbs/Gbs units
- enhance the QP context struct to contain rate limit units and value
- allow to do run time rate-limit setting to QPs through the
update-qp firmware command
- QP rate-limiting is disallowed for VFs
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Added resource initialization based on port-id field
- Enabled second SGMII 1G interface
Signed-off-by: Keyur Chudgar <kchudgar@apm.com>
Signed-off-by: Iyappan Subramanian <isubramanian@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
of_device_id is always used as const.
(See driver.of_match_table and open firmware functions)
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
of_device_id is always used as const.
(See driver.of_match_table and open firmware functions)
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
of_device_id is always used as const.
(See driver.of_match_table and open firmware functions)
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
of_device_id is always used as const.
(See driver.of_match_table and open firmware functions)
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
of_device_id is always used as const.
(See driver.of_match_table and open firmware functions)
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
of_device_id is always used as const.
(See driver.of_match_table and open firmware functions)
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
of_device_id is always used as const.
(See driver.of_match_table and open firmware functions)
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
of_device_id is always used as const.
(See driver.of_match_table and open firmware functions)
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
of_device_id is always used as const.
(See driver.of_match_table and open firmware functions)
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
of_device_id is always used as const.
(See driver.of_match_table and open firmware functions)
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
of_device_id is always used as const.
(See driver.of_match_table and open firmware functions)
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
of_device_id is always used as const.
(See driver.of_match_table and open firmware functions)
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
of_device_id is always used as const.
(See driver.of_match_table and open firmware functions)
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
MDIO controller on little endian Socs, e.g. ls2085a is similar to the
controller on big endian Socs, but the MDIO access is little endian,
we use I/O accessor function to handle endianness, so the driver can
run on little endian Socs. A property "little-endian" is used
in DTS to indicate the MDIO is little endian, if driver probes the
property, driver will access MDIO in little endian, otherwise, driver
works in big endian by default.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a bug in xgmac_wait_until_done() which mdio_stat should be used
instead of mdio_data when checking if busy bit is cleared.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In hast to fix some sparse warning, I hard-coded a fix-sized array on the stack
which is probably too big for kernel standards. Fix this by converting array
to dynamic allocation.
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Acked-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move swdev wrappers over to new swdev ops (from previous ndo ops). No
functional changes to the implementation.
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
rocker: move to new swdev ops
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
dsa: move to new swdev ops
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for Hardware Filter Block (HFB) so that incoming Rx traffic
can be matched and directed to desired Rx queues.
Signed-off-by: Petri Gynther <pgynther@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use of_property_read*() to get arch endian consistent
property values. Do some refactoring in the process.
Signed-off-by: Jingchang Lu <jingchang.lu@freescale.com>
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use conversion macros to correctly access the BE
fields of the Rx and Tx Frame Control Block on LE CPUs.
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use conversion macros to correctly access the BE
fields of the Rx and Tx Buffer Descriptors on LE CPUs.
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the macro to copy the Ethernet address instead of memcpy().
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Fix the code comments to align with drivers/net/ code commenting style,
as well as whitespace issues. The whitespace issues resolve checkpatch
errors, like lines exceeding 80 chars (except for strings) and the use
of tabs where possible.
CC: <kernel-team@fb.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
This patch removes some dead code from the cleanup path for ixgbe.
Setting and clearing the flag doesn't do anything since all we are
doing is setting the flag, scheduling NAPI, clearing the flag and
then letting netpoll do the polling cleanup. As such it doesn't
make much sense to have it there.
This patch also removes one minor white-space error.
CC: <kernel-team@fb.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch makes sure that relaxed ordering is not disabled when
on SPARC, where it helps with performance.
CC: <kernel-team@fb.com>
CC: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Reported-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Correcting a mistake when I initial created this function. I should
have made this static since it is only referenced where the function
pointer is assigned.
CC: <kernel-team@fb.com>
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Missed this when I created commit 6a14ee0cfb ("ixgbe: Add X550 support
function pointers"). Use a the __be* type to be consistent with how the
value is assigned.
CC: <kernel-team@fb.com>
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
For the X550 mac type we have to do additional steps around
enabling/disabling Rx. This patch will add a layer of indirection
around these support functions to enable this.
CC: <kernel-team@fb.com>
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Delay the update of the TDMA producer index unless this is the last SKB
in a batch, or the queue is already stopped. Move the check for whether
the queue should be stopped before the xmit_more check to avoid locking
the transmit queue in case there was a SKB submitted which has xmit_more
set.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no need to have both bcmgenet_xmit_single() and
bcmgenet_xmit_frag() perform a free_bds decrement and a prod_index
increment by one. In case one of these functions fails to map a SKB or
fragment for transmit, we will return and exit bcmgenet_xmit() with an
error.
We can therefore safely use our local copy of nr_frags to know by how
much we should decrement the number of free buffers available, and by
how much the producer count must be incremented and do this in the tail
of bcmgenet_xmit().
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Petri Gynther <pgynther@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, bcmgenet_desc_rx() calls bcmgenet_rx_refill() at the end of
Rx packet processing loop, after the current Rx packet has already been
passed to napi_gro_receive(). However, bcmgenet_rx_refill() might fail
to allocate a new Rx skb, thus leaving a hole on the Rx queue where no
valid Rx buffer exists.
To eliminate this situation:
1. Rewrite bcmgenet_rx_refill() to retain the current Rx skb on the Rx
queue if a new replacement Rx skb can't be allocated and DMA-mapped.
In this case, the data on the current Rx skb is effectively dropped.
2. Modify bcmgenet_desc_rx() to call bcmgenet_rx_refill() at the top of
Rx packet processing loop, so that the new replacement Rx skb is
already in place before the current Rx skb is processed.
Signed-off-by: Petri Gynther <pgynther@google.com>
Tested-by: Jaedon Shin <jaedon.shin@gmail.com>--
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PHY state machine (in drivers/net/phy/phy.c) will unconditionally
call phydev->adjust_link (macb_handle_link_change) when polling in the
PHY_CHANGELINK state. As currently written, macb always ends up
requesting a new tx_clk frequency in macb_handle_link_change. It is a
waste of time to request a new tx_clk frequency if the link state hasn't
changed, as the tx_clk will already be configured properly.
Let's only request a new tx_clk clock frequency when necessary.
Signed-off-by: Jaeden Amero <jaeden.amero@ni.com>
Cc: Josh Cartwright <joshc@ni.com>
Cc: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The semantic patch that fixes this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r@
type T;
identifier f;
@@
static T f (...) { ... }
@@
identifier r.f;
declarer name EXPORT_SYMBOL;
@@
-EXPORT_SYMBOL(f);
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bits 31:16 of RDMA_PROD_INDEX contain Rx discarded packet count, which
are the Rx packets that had to be dropped by MAC hardware since there
was no room on the Rx queue. Add code to collect this information into
the netdev stats.
Signed-off-by: Petri Gynther <pgynther@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
FSL_PQ_MDIO and FSL_XGMAC_MDIO are not really depend on FSL_SOC, they
can build on non-PPC platforms.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The code removed by commit 421d9df062 ("net/macb: merge
at91_ether driver into macb driver") should be removed
in the merge resolution as well.
Signed-off-by: David S. Miller <davem@davemloft.net>
Pass in the netlink flags (NLM_F_*) into switchdev driver for IPv4 FIB add op
to allow driver to 1) optimize hardware updates, 2) handle ip route prepend
and append commands correctly.
Suggested-by: Jamal Hadi Salim <jhs@mojatatu.com>
Suggested-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Acked-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/cadence/macb.c
Overlapping changes in macb driver, mostly fixes and cleanups
in 'net' overlapping with the integration of at91_ether into
macb in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
1. Add struct bcmgenet_rx_ring to hold all necessary information
for a single Rx queue.
2. Add bcmgenet_init_rx_queues() to initialize all Rx queues.
3. Modify bcmgenet_init_rx_ring() to initialize a single Rx queue.
4. Modify Rx interrupt path code to use per-queue data.
5. Modify bcmgenet_rx_refill() to use RxCB->bd_addr.
Signed-off-by: Petri Gynther <pgynther@google.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The configurations are not modified by the driver. Make them 'const' so
that they may be placed in a read-only section.
Signed-off-by: Josh Cartwright <joshc@ni.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for setting the RSS hash table and hash key through ethtool.
This patch incorporates suggestions from Ben Hutchings
<ben.hutchings@codethink.co.uk>.
Reported-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Bump PF version to 1.2.37 and VF version to 1.2.25
Change-ID: I0287a750408250dc055c03e1f744fd5f0caefd68
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Print the LAN, SAN, and Port MACs for the VSI if debugfs command
dump VSI is used on the PF's VSI.
Example output:
[260221.871244] i40e 0000:04:00.0: MAC address: 68:05:ca:26:15:e0 SAN MAC: 00:00:00:00:02:00 Port MAC: 68:05:ca:26:15:e3
Change-ID: I0b393113dfb5ee7ff4f9e5227e4177885f0cc15e
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Joe Perches pointed out that we were inconsistent in the use of
PF vs pf or VF vs vf in our driver code. Since acronyms are usually
capitalized to denote that it is an acronym, changed all references to
be consistent throughout the code.
Reported-by: Joe Perches <joe@perches.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The NVMUpdate tool doesn't necessarily know the ReadOnly map of the current
NVM image, and must try reading and writing words that may be protected.
This generates an error out of the Firmware request that the driver logs.
Unfortunately, this ends up spitting out hundreds of bogus read and write
error message that looks rather messy.
This patch checks the error type and under normal conditions will not print
the typical read and write errors during NVMUpdate. This can be overridden
by enabling the NVM update debugging. This results in a much less messy log
file, and likely many fewer customer support questions.
Change-ID: Id4ff2e9048c523b0ff503aa5ab181b025ec948ea
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fix a bug introduced in the force writeback code, where the interrupt
rate was set to 0 (maximum) by accident.
The driver must correctly set the NOITR fields to avoid ITR update
as a side effect of triggering the software interrupt.
Change-ID: I290851ae04ef3811c43aab5ee33242029f26c1a3
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If a reset occurs when the netdev is closed, the reset task will hang in
napi_disable, causing deadlocks and general grumpiness.
Check to make sure the device is actually running before stopping
everything. This allows the reset task to complete and have a real good
time.
Change-ID: Iaaea84acbcb9b3810c216b14c3326e4287b75b58
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Make sure the sizeof() calls are taking the size of the actual struct
that we care about. By using the pointer variable, we'll always get
the right struct size, even if the variable type changes sometime in
the future.
Change-ID: Id5858f883cf42447365ea3733080d7714f975bce
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
