The patch adds LD9040 parallel RGB panel driver with SPI control interface.
The driver uses drm_panel framework.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
The patch adds driver for Exynos DSI master (DSIM). It is a platform driver
which is registered as exynos_drm_display sub-driver of exynos_drm framework
and implements DRM encoder/connector pair.
It is also MIPI-DSI host driver and provides DSI bus for panels.
It interacts with its panel(s) using drm_panel framework.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
The patch adds DT bindings for Exynos DSI Master. DSIM follows rules
for DSI bus host bindings [1].
Properties describes its resources: memory, interrupt, clocks,
phy, regulators, frequencies of clocks and video interfaces.
[1]: Documentation/devicetree/bindings/mipi/dsi/mipi-dsi-bus.txt
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
This patch adds explicit check if there is a connector with
connected status before fbdev initialization. It prevents creation
of default fbdev 1024x768 which is unusable on panels with bigger resolutions.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
MIPI DSI host node can contain child nodes which are not DSI devices.
Checking for existence of reg property can be used to distinguish such nodes.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
This patch adds flags field to mipi_dsi_msg structure and two flags:
- MIPI_DSI_MSG_REQ_ACK - request ACK from peripheral for given message,
- MIPI_DSI_MSG_USE_LPM - use Low Power Mode to transmit message.
The first flag is usually helpful during DSI diagnostic, the second
flag is required by some peripherals during configuration phase.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
The Dell XPS 8700 has a onboard Display port and HDMI port and no VGA port.
The call intel_crt_init freeze the machine, so skip such call.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=73559
Signed-off-by: Giacomo Comes <comes at naic.edu>
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This typo may lead to missed RPS interrupts and as a result a too
low or too high frequency for the current workload. The interrupt mask
will be set properly at a subsequent GPU idle event, but can get
corrupted again at the next RPS up/down event.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
As per the inputs provided by hardware team we still use DDR
Rates as 0,1=800, 2=1066, 3=1333.
With this change, Turbo freqs used on current machines matches.
This reverts commit f64a28a7c5.
commit f64a28a7c5
Author: Jesse Barnes <jbarnes@virtuousgeek.org>
Date: Mon Nov 4 16:07:00 2013 -0800
drm/i915/vlv: fixup DDR freq detection per Punit spec
v2: Add reference to previous commit which changed this. (Daniel)
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Deepak S <deepak.s@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
During resume the intel hda audio driver depends on the i915 driver
reinitializing the audio power domain. Since the order of calling the
i915 resume handler wrt. that of the audio driver is not guaranteed,
move the power domain reinitialization step to the resume_early
handler. This is guaranteed to run before the resume handler of any
other driver.
The power domain initialization in turn requires us to enable the i915
pci device first, so move that part earlier too.
Accordingly disabling of the i915 pci device should happen after the
audio suspend handler ran. So move the disabling later from the i915
resume handler to the resume_late handler.
v2:
- move intel_uncore_sanitize/early_sanitize earlier too, so they don't
get reordered wrt. intel_power_domains_init_hw()
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=76152
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Cc: stable@vger.kernel.org
[danvet: Add cc: stable and loud comments that this is just a hack.]
[danvet: Fix "Should it be static?" sparse warning reported by Wu
Fengguang's kbuilder.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Use the more canonical and concise variant of the GPL v2 license text.
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The majority of the code in this driver is licensed under the GPL v2, so
relicense the rest under GPL v2 as well for consistency.
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This file will eventually be exported to libdrm, where all the public
header files use the MIT license.
Reported-by: Erik Faye-Lund <kusmabite@gmail.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Emil Goode <emilgoode@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add support for eDP functionality found on Tegra124 and later SoCs. Only
fast link training is currently supported.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Tegra V4L2 camera driver needs this function to do frame capture.
Signed-off-by: Bryan Wu <pengw@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This panel is used by Tegra Note 7 and supported by the simple-panel
driver.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This panel is used by the NVIDIA SHIELD and supported by the
simple-panel driver.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
In order to differentiate between the different video modes (burst vs.
non-burst, sync pulses vs. sync events) supported by peripherals, pass
the flags that specify this mode in the panel description to the DSI
peripheral device when probed.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The enable GPIO for panels may be provided by GPIO expanders on slow
busses (such as I2C), and therefore toggling the GPIO may sleep. Since
these accesses don't happen in interrupt context, use the *_cansleep()
variants of the GPIO API.
Signed-off-by: Thierry Reding <treding@nvidia.com>
regulator_disable() is already performed by panel_simple_disable(),
which is called by panel_simple_remove().
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Use the new GPIO descriptor interface to handle the panel's enable GPIO.
This considerably simplifies the code.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
[treding@nvidia.com: rework to improve readability]
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add myself as the maintainer for DRM panel drivers. The plan is to
collect panel-related patches in one place to reduce conflicts and
unburden Dave.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Use the %pad printk specifier to print dma_addr_t variables. This fixes
warnings on platforms where dma_addr_t has a different size than int or
size_t.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The GEM CMA helpers uses a custom mmap implementation based on
remap_pfn_range(). While this works when the buffer DMA and physical
addresses are identical, it fails to take IOMMU into account and tries
to mmap the buffer to userspace using the DMA virtual address instead of
the physical address. This results in mapping random physical pages when
the device is behind an IOMMU.
Use the DMA mapping dma_mmap_writecombine() function instead.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Tested-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
entry->size is the size of the node, not the size of the hole after it.
So the code would actually find the hole which can satisfy the
constraints and which is preceded by the smallest node, not the smallest
hole satisfying the constraints.
Reported-by: "Huang, FrankR" <FrankR.Huang@amd.com>
Signed-off-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The following error and warnings will be seen when compiling a C file
which includes <drm/drm_gem_cma_helper.h> but without <drm/drmP.h>
being included before.
include/drm/drm_gem_cma_helper.h:5:24: error: field ‘base’ has incomplete type
include/drm/drm_gem_cma_helper.h: In function ‘to_drm_gem_cma_obj’:
include/drm/drm_gem_cma_helper.h:16:9: warning: initialization from incompatible pointer type [enabled by default]
include/drm/drm_gem_cma_helper.h: At top level:
include/drm/drm_gem_cma_helper.h:24:34: warning: ‘struct drm_mode_create_dumb’ declared inside parameter list [enabled by default]
include/drm/drm_gem_cma_helper.h:24:34: warning: its scope is only this definition or declaration, which is probably not what you want [enabled by default]
include/drm/drm_gem_cma_helper.h:24:34: warning: ‘struct drm_device’ declared inside parameter list [enabled by default]
include/drm/drm_gem_cma_helper.h:24:34: warning: ‘struct drm_file’ declared inside parameter list [enabled by default]
include/drm/drm_gem_cma_helper.h:28:10: warning: ‘struct drm_device’ declared inside parameter list [enabled by default]
include/drm/drm_gem_cma_helper.h:28:10: warning: ‘struct drm_file’ declared inside parameter list [enabled by default]
include/drm/drm_gem_cma_helper.h:35:3: warning: ‘struct drm_device’ declared inside parameter list [enabled by default]
include/drm/drm_gem_cma_helper.h:46:14: warning: ‘struct drm_device’ declared inside parameter list [enabled by default]
Fix them by including <drm/drmP.h> in drm_gem_cma_helper.h.
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Currently drm_pick_cmdline_mode() doesn't care about the interlace
when the given mode line has no "i" suffix. That is, when there are
multiple entries for the same resolution, an interlace mode might be
picked up just depending on the assigned order, and there is no way to
exclude it.
This patch changes the logic for the mode selection, to prefer the
noninterlace mode unless the interlace mode is explicitly given.
When no matching mode is found, it still tries the interlace mode as
fallback.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This decreases eviction by up to 20%, by improving the fragmentation
quality. No harm in normal cases that fit VRAM fully (PTS gaming suite).
In some cases, even the VRAM-fitting cases improved slightly (openarena, urban terror).
512kb was measured as the most optimal threshold for 3d workloads common to radeon.
Other drivers may need different thresholds according to their workloads.
v2: Nicer formatting
Signed-off-by: Lauri Kasanen <cand@gmx.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Clients like i915 need to segregate cache domains within the GTT which
can lead to small amounts of fragmentation. By allocating the uncached
buffers from the bottom and the cacheable buffers from the top, we can
reduce the amount of wasted space and also optimize allocation of the
mappable portion of the GTT to only those buffers that require CPU
access through the GTT.
For other drivers, allocating small bos from one end and large ones
from the other helps improve the quality of fragmentation.
Based on drm_mm work by Chris Wilson.
v3: Changed to use a TTM placement flag
v2: Updated kerneldoc
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Ben Widawsky <ben@bwidawsk.net>
Cc: Christian König <deathsimple@vodafone.de>
Signed-off-by: Lauri Kasanen <cand@gmx.com>
Signed-off-by: David Airlie <airlied@redhat.com>
* 'msm-next' of git://people.freedesktop.org/~robclark/linux:
drm/omap: Don't dereference list head when the connectors list is empty
drm/msm/mdp: add timeout for irq wait
drm/msm: validate flags, etc
drm/msm: use componentised device support
drm/msm: add chip-id param
drm/msm: crank down gpu when inactive
drm/msm: spin helper
drm/msm: add hang_debug module param
drm/msm: hdmi audio support
The rcar_du_encoder_init() function can fail and return an error code.
Don't ignore it.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
- Rework of finding the right PLL numbers for display
- Couple of different bugfixes
* 'drm-next-3.15' of git://people.freedesktop.org/~deathsimple/linux:
drm/radeon: fix typo in spectre_golden_registers
drm/radeon: fix endian swap on hawaii clear state buffer setup
drm/radeon: call drm_edid_to_eld when we update the edid
drm/radeon: rework finding display PLL numbers v2
drm/radeon: fix resuming mode in pm runtime resume path
drm/radeon: fix runtime suspend breaking secondary GPUs
drm/radeon: clear needs_reset flag if IB test fails
Print the enable_mask and status_mask from
__i915_{enable,disable}_pipestat() when the caller has messed them up
somehow.
v2: Use pipe_name() (Damien)
Fix a typo in the commit message
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In commit a51435a313
Author: Naresh Kumar Kachhi <naresh.kumar.kachhi@intel.com>
Date: Wed Mar 12 16:39:40 2014 +0530
drm/i915: disable rings before HW status page setup
we reordered stopping the rings to do so before we set the HWS register.
However, there is an extra workaround for g45 to reset the rings twice,
and for consistency we should apply that workaround before setting the
HWS to be sure that the rings are truly stopped.
Cc: Naresh Kumar Kachhi <naresh.kumar.kachhi@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Need to swap on BE.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Cc: stable@vger.kernel.org
This needs to be done to update some of the fields in
the connector structure used by the audio code.
Noticed by several users on irc.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Christian König <christian.koenig@amd.com>
Cc: stable@vger.kernel.org
This completely reworks how the PLL parameters are generated and
should result in better matching dot clock frequencies.
Probably needs quite a bit of testing.
bugs: https://bugs.freedesktop.org/show_bug.cgi?id=76564
v2: more cleanup and comments.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
For runtime pm we'd never suspend with the modesetting hw turned on,
so don't try and resume the modesetting hw, as that path will take
locks that the interface that is causing us to wake up might also
take.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Same fix as for nouveau, when we fail with EINVAL, subsequent
gets fail hard, causing the device not to open.
Signed-off-by: Dave Airlie <airlied@redhat.com>
If the IB test fails we don't want to reset the card over
and over again, just accept that it isn't working.
Bug: https://bugs.freedesktop.org/show_bug.cgi?id=76501
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
We have been setting the bit which was originally BIOS dependent since:
commit f05bb0c7b6
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Sun Jan 20 16:33:32 2013 +0000
drm/i915: GFX_MODE Flush TLB Invalidate Mode must be '1' for scanline waits
Therefore, we do not need to try to figure it out dynamically and we can
just always invalidate the TLBs.
It's a partial revert of:
commit 12b0286f49
Author: Ben Widawsky <ben@bwidawsk.net>
Date: Mon Jun 4 14:42:50 2012 -0700
drm/i915: possibly invalidate TLB before context switch
The original commit attempted to only invalidate when necessary
(very much a relic from the old days). Now, we can just always invalidate.
I guess the old TODO still exists. Since we seem to have abandoned ILK
contexts however, there isn't much point in even remembering.
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The framecount register was still using the old PIPE macro instead
of the new PIPE2 macro
Signed-off-by: Rafael Barbalho <rafael.barbalho@intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
DPIO reads from groups/broadcast register offsets for PCS and
TX return all 1's. If that result gets used for something
we'll probably end up doing something wrong. So warn when that
happens.
FIXME there might be some registers where all 1's is a valid value,
so ideally we should check the register offset instead...
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[danvet: copypaste the FIXME comment into the code.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
There's no point in hiding the DP M/N setup in the update_pll functions.
Just move it to the mode_set function.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
