When this was added not all the remaining defines were switched over to
use enums, so let's complete that process here
Reported-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Matthew McClintock <mmcclint@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The qcom_reset_ops structure is never modified. Make it const.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The offset seems to have been copied from the sata clk. Fix it so
that enabling the crypto engine source clk works.
Tested-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Tested-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Fixes: 5f775498bd ("clk: qcom: Fully support apq8064 global clock control")
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The clk_rcg_pixel_set_rate clk_op sets up the pre-divider by reading
its current value from the NS register.
Using the pre-divider wasn't really intended when creating these ops.
The pixel RCG was only intended to achieve fractional multiplication
provided in the pixel_table array. Leaving the pre-divider to the
existing register value results in a wrong pixel clock when the
bootloader sets up the display. This was left unidentified because
the IFC6410 Plus board on which this was verified didn't have a
bootloader that configured the display.
Don't set the RCG pre-divider in freq_tbl to the existing NS register
value. Force it to 1 and only use the M/N counter to achieve the desired
fractional multiplication.
Cc: Vinay Simha <vinaysimha@inforcecomputing.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Tested-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This patch adds support for the global clock controller found on
the IPQ4019 based devices. This includes UART, I2C, SPI etc.
Signed-off-by: Pradeep Banavathi <pradeepb@codeaurora.org>
Signed-off-by: Senthilkumar N L <snlakshm@codeaurora.org>
Signed-off-by: Varadarajan Narayanan <varada@codeaurora.org>
Signed-off-by: Matthew McClintock <mmcclint@codeaurora.org>
Acked-by: Andy Gross <andy.gross@linaro.org>
[sboyd@codeaurora.org: Drop 0x16024 enable_reg in crypto_ahb]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This patch corrects the enable register offset which is actually 0x36cc
instead of 0x36c4
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Fixes: 5f775498bd ("clk: qcom: Fully support apq8064 global clock control")
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This reverts commit 329cabcecf.
The commit that caused us to specify LE device endianness here,
29bb45f25f (regmap-mmio: Use native endianness for read/write,
2015-10-29), has been reverted in mainline so now when we specify
LE it actively breaks big endian kernels because the byte
swapping in regmap-mmio is incorrect. Let's revert this change
because it will 1) fix the big endian kernels and 2) be redundant
to specify LE because that will become the default soon.
Cc: Kevin Hilman <khilman@linaro.org>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Cc: Mark Brown <broonie@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
With gdsc driver capable of handling hierarchical power domains,
specify oxili_gdsc as parent of oxilicx_gdsc.
Remove all direct calls to genpd from the mmcc clock driver. The
adding and removing of subdomains is now handled from within
the gdsc driver.
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Add all gdsc data which are part of mmcc on msm8996 family
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Add all data for the GDSCs which are part of msm8996 GCC block
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Some gdscs might be controlled via voting registers and might not
really disable when the kernel intends to disable them (due to other
votes keeping them enabled)
Mark these gdscs with a flag for we do not check/wait on a disable
status for these gdscs within the kernel disable callback.
Also at boot, if these GDSCs are found to be ON, we make sure we
vote for them before we inform the genpd framework about their
status. If genpd gets no users, it then disables (removes the vote)
them as part of genpd_poweroff_unused()
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Some gdsc power domains can have a gds_hw_controller block inside
to help ensure all slave devices within the power domain are idle
before the gdsc is actually switched off.
This is mainly useful in power domains which host a MMU, in which
case its necessary to make sure there are no outstanding MMU operations
or pending bus transactions before the power domain is turned off.
In gdscs with gds_hw_controller block, its necessary to check the
gds_hw_ctrl status bits instead of the ones in gdscr, to determine
the state of the powerdomain.
While at it, also move away from using jiffies and use ktime APIs
instead for busy looping on status bits.
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Some qcom SoCs' can have hierarchical power domains. Let the gdsc structs
specify the parents (if any) and the driver add genpd subdomains for them.
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
We were not checking the return from devm_add_action() which can fail.
Start using the helper and devm_add_action_or_reset() and return
directly as we know that the cleanup has been done by this helper.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This clock is required for loading the qdsp firmware.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Add a driver for the multimedia clock controller found on MSM8996
based devices. This should allow most multimedia device drivers
to probe and control their clocks.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The GPU clocks on msm8996 have three dedicated PLLs, MMPLL2,
MMPLL8, and MMPLL9. We leave MMPLL9 at the maximum speed (624
MHz), and we use MMPLL2 and MMPLL8 for the other frequencies. To
make switching frequencies faster, we ping-pong between MMPLL2
and MMPLL8 when we're switching between frequencies that aren't
the maximum. Implement custom rcg clk ops for this type of
frequency switching.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Add support for the global clock controller found on MSM8996
based devices. This should allow most non-multimedia device
drivers to probe and control their clocks.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Add support for configuring rates of, enabling, and disabling
Alpha PLLs. This is sufficient for the types of PLLs found in
the global and multimedia clock controllers.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Move the xo and sleep clocks to device-tree, instead of hard-coding
them in the driver. This allows us to insert the RPM clocks (if they
are enabled) in between the on-board oscillators and the actual clock.
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
All these clock controllers are little endian devices, but so far
we've been relying on the regmap mmio bus handling this for us
without explicitly stating that fact. After commit 4a98da2164cf
(regmap-mmio: Use native endianness for read/write, 2015-10-29),
the regmap mmio bus will read/write with the __raw_*() IO
accessors, instead of using the readl/writel() APIs that do
proper byte swapping for little endian devices.
So if we're running on a big endian processor and haven't
specified the endianness explicitly in the regmap config or in
DT, we're going to switch from doing little endian byte swapping
to big endian accesses without byte swapping, leading to some
confusing results. On my apq8074 dragonboard, this causes the
device to fail to boot as we access the clock controller with
big endian IO accesses even though the device is little endian.
Specify the endianness explicitly so that the regmap core
properly byte swaps the accesses for us.
Reported-by: Kevin Hilman <khilman@linaro.org>
Tested-by: Tyler Baker <tyler.baker@linaro.org>
Tested-by: Kevin Hilman <khilman@linaro.org>
Cc: Simon Arlott <simon@fire.lp0.eu>
Cc: Mark Brown <broonie@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Put these clocks into the dt files instead of registering them
from C code. This provides a few benefits. It allows us to
specify the frequency of these clocks at the board level instead
of hard-coding them in the driver. It allows us to insert an RPM
clock in between the consumers of the crystals and the actual
clock. And finally, it helps us transition the GCC driver to use
RPM clocks when that configuration is enabled.
Cc: Georgi Djakov <georgi.djakov@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
We want to put the XO board clocks into the dt files, but we also
need to be backwards compatible with an older dtb. Add an API to
the common code to do this. This also makes a place for us to
handle the case when the RPM clock driver is enabled and we don't
want to register the fixed factor clock.
Cc: Georgi Djakov <georgi.djakov@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The halt bits for these clocks seem wrong. I get the following
warning while booting on an msm8960-cdp:
WARNING: CPU: 0 PID: 1 at drivers/clk/qcom/clk-branch.c:97 clk_branch_toggle+0xd0/0x138()
dsi1_clk status stuck at 'on'
Modules linked in:
CPU: 0 PID: 1 Comm: swapper/0 Not tainted 4.3.0-rc3-00113-g5532cfb567fe #110
Hardware name: Qualcomm (Flattened Device Tree)
[<c0216984>] (unwind_backtrace) from [<c02138f8>] (show_stack+0x10/0x14)
[<c02138f8>] (show_stack) from [<c04a525c>] (dump_stack+0x70/0xbc)
[<c04a525c>] (dump_stack) from [<c0223c70>] (warn_slowpath_common+0x78/0xb4)
[<c0223c70>] (warn_slowpath_common) from [<c0223d40>] (warn_slowpath_fmt+0x30/0x40)
[<c0223d40>] (warn_slowpath_fmt) from [<c05fc2dc>] (clk_branch_toggle+0xd0/0x138)
[<c05fc2dc>] (clk_branch_toggle) from [<c05f3f3c>] (clk_disable_unused_subtree+0x98/0x1b0)
[<c05f3f3c>] (clk_disable_unused_subtree) from [<c05f3ec4>] (clk_disable_unused_subtree+0x20/0x1b0)
[<c05f3ec4>] (clk_disable_unused_subtree) from [<c05f5474>] (clk_disable_unused+0x58/0xd8)
[<c05f5474>] (clk_disable_unused) from [<c0209710>] (do_one_initcall+0xac/0x1ec)
[<c0209710>] (do_one_initcall) from [<c0991db4>] (kernel_init_freeable+0x11c/0x1e8)
[<c0991db4>] (kernel_init_freeable) from [<c0727ae0>] (kernel_init+0x8/0xec)
[<c0727ae0>] (kernel_init) from [<c0210238>] (ret_from_fork+0x14/0x3c)
Fix the status bits and the errors go away.
Fixes: 5532cfb567 ("clk: qcom: mmcc-8960: Add DSI related clocks")
Acked-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Add rcg and branch clk structs for DSI1 and DSI2 blocks found in MSM8960
and APQ8064. Each DSI instance has 4 pairs of rcg and branch clocks.
Populate arrays mmcc_msm8960_clks and mmcc_apq8064_clks with these clocks.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
DSI specific RCG clocks required customized clk_ops. There are
a total of 4 RCGs per DSI block: DSI, BYTE, ESC and PIXEL.
There are a total of 2 clocks coming from the DSI PLL, which serve as
inputs to these RCGs. The BYTE and ESC RCGs are fed by one of the
post dividers of DSI1 or DSI2 PLLs, and the DSI and PIXEL RCGs are fed by
another divider of the PLL.
In each of the 2 groups above, only one of the clocks sets its parent.
These are BYTE RCG and DSI RCG for each of the groups respectively, as
shown in the diagram below.
The DSI and BYTE RCGs serve as bypass clocks. We create a new set of ops
clk_rcg_bypass2_ops, which are like the regular bypass ops, but don't
take in a freq table, since the DSI driver using these clocks is
parent-able.
The PIXEL RCG needs to derive the required pixel clock using dsixpll.
It parses a m/n frac table to retrieve the correct clock.
The ESC RCG doesn't have a frac M/N block, it can just apply a pre-
divider. Its ops simply check if the required clock rate can be
achieved by the pre-divider.
+-------------------+
| |---dsixpllbyte---o---> To byte RCG
| | | (sets parent rate)
| | |
| | |
| DSI 1/2 PLL | |
| | o---> To esc RCG
| | (doesn't set parent rate)
| |
| |----dsixpll-----o---> To dsi RCG
+-------------------+ | (sets parent rate)
( x = 1, 2 ) |
|
o---> To pixel rcg
(doesn't set parent rate)
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
8960 family of devices have TSENS as part of GCC in hardware.
Hence DT would represent a GCC node with GCC properties as well
as TSENS. Create a virtual platform child device here for TSENS
so the driver can probe it and use the parent (GCC) to extract DT
properties.
Suggested-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
[sboyd@codeaurora.org: Massaged to work with devm friendly
qcom_cc_probe()]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Having this hidden config below the COMMON_CLK_QCOM config causes
menuconfig to stop indenting config items after it.
<*> Support for Qualcomm's clock controllers
{M} APQ8084 Global Clock Controller
<M> APQ8084 Multimedia Clock Controller
{M} IPQ806x Global Clock Controller
<M> IPQ806x LPASS Clock Controller
<M> MSM8660 Global Clock Controller
<M> MSM8916 Global Clock Controller
{M} APQ8064/MSM8960 Global Clock Controller
<M> APQ8064/MSM8960 LPASS Clock Controller
<M> MSM8960 Multimedia Clock Controller
{M} MSM8974 Global Clock Controller
<M> MSM8974 Multimedia Clock Controller
Move it up above anything else so that we don't get odd
indenting.
Cc: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Now that qcom_cc_remove() is a nop, drop calls to
qcom_cc_remove() and any empty driver remove functions.
Cc: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Some APIs in qcom_cc_probe() don't have a devm counterpart, so we
have to use the calling device's platform data to pass pointers
to the remove path. Let's use devm_add_action() instead, so that
the remove path doesn't need to do anything, allowing us to
remove qcom_cc_remove() entirely.
Cc: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The oxili_cx GDSC is inside the power domain of the oxili GDSC.
Add the dependency so that the CX domain can properly power up.
Reported-by: Rob Clark <robdclark@gmail.com>
Cc: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Add support for the msm8916 audio clocks. This includes core bus,
low-power audio and codec clocks. They are required for audio playback.
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Add support for the msm8916 BIMC (Bus Integrated Memory Controller)
clocks that are needed for GPU.
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Some root clock generators may have child branches that are controlled
by different CPUs. These RCGs require some special operations:
- some enable bits have to be toggled when we set the rate;
- if RCG is disabled we only cache the rate and set it later when enabled;
- when the RCG is disabled, the mux is set to the safe source;
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
[sboyd@codeaurora.org: Simplify recalc_rate implementation]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Add support for the msm8916 TCU (Translation Control Unit) clocks that
are needed for IOMMU.
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Add the GDSC instances that exist as part of apq8084 MMCC block.
Signed-off-by: Stephane Viau <sviau@codeaurora.org>
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Add the GDSC instances that exist as part of apq8084 GCC block
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Add the GDSC instances that exist as part of msm8974 MMCC block
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
There's just one GDSC as part of the msm8974 GCC block.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Add all data for the GDSCs which are part of msm8916 GCC block.
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Certain devices can have GDSCs' which support ON as the only state.
They can't be power collapsed to either hit RET or OFF.
The clients drivers for these GDSCs' however would expect the state
of the core to be reset following a GDSC disable and re-enable.
To do this assert/deassert reset lines every time the client
driver would request the GDSC to be powered on/off instead.
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Along with the GDSC power switch, there is additional control
to either retain all memory (core and peripheral) within a given
powerdomain or to turn them off while the GDSC is powered down.
Add support for these by modelling a RET state where all
memory is retained and an OFF state where all memory gets turned
off.
The controls provided are granular enough to be able to support
various differnt levels of RET states, like a 'shallow RET' with all memory
retained and a 'deep RET' with some memory retained while some others
are lost. The current patch does not support this and considers
just one RET state where all memory is retained. Futher work, if
needed can support multiple different levels of RET state.
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The common clk probe registers a clk provider and a reset controller.
Update it to register a genpd provider using the gdsc data provided
by each platform.
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
GDSCs (Global Distributed Switch Controllers) are responsible for
safely collapsing and restoring power to peripherals in the SoC.
These are best modelled as power domains using genpd and given
the registers are scattered throughout the clock controller register
space, its best to have the support added through the clock driver.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Sometimes the display driver may want to change the parent PLL of
the display clocks (byte and pixel clocks) depending on the
use-case. Currently the parent is fixed by means of having a
frequency table with one entry that chooses a particular parent.
Remove this restriction and use the parent the clock is
configured for in the hardware during clk_set_rate(). This
requires consumers to rely on the default parent or to configure
the parent with clk_set_parent()/assigned-clock-parents on the
clocks before calling clk_set_rate().
Tested-by: Archit Taneja <architt@codeaurora.org>
Cc: Hai Li <hali@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Fix the enable bit of the pseudorandom number generator clock.
Reported-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Fixes: 3966fab8b6 "clk: qcom: Add MSM8916 Global Clock Controller support"
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Use the provider based method to get a clock's name so that we
can get rid of the clk member in struct clk_hw one day. Mostly
converted with the following coccinelle script.
@@
struct clk_hw *E;
@@
-__clk_get_name(E->clk)
+clk_hw_get_name(E)
Acked-by: Heiko Stuebner <heiko@sntech.de>
Cc: Sylwester Nawrocki <s.nawrocki@samsung.com>
Cc: Tomasz Figa <tomasz.figa@gmail.com>
Cc: Peter De Schrijver <pdeschrijver@nvidia.com>
Cc: Prashant Gaikwad <pgaikwad@nvidia.com>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Acked-by: Thierry Reding <treding@nvidia.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: Tero Kristo <t-kristo@ti.com>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Acked-by: Andrew Bresticker <abrestic@chromium.org>
Cc: Ezequiel Garcia <ezequiel.garcia@imgtec.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Kevin Cernekee <cernekee@chromium.org>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-rockchip@lists.infradead.org
Cc: linux-samsung-soc@vger.kernel.org
Cc: linux-tegra@vger.kernel.org
Cc: linux-omap@vger.kernel.org
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
We're removing struct clk from the clk provider API, so switch
this code to using the clk_hw based provider APIs.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Mostly converted with the following snippet:
@@
struct clk_hw *E;
@@
-__clk_get_flags(E->clk)
+clk_hw_get_flags(E)
Acked-by: Tero Kristo <t-kristo@ti.com>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Acked-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Cc: Daniel Thompson <daniel.thompson@linaro.org>
Cc: Coquelin <mcoquelin.stm32@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The missing license causes the clk-qcom.ko module to taint the
kernel. Add the appropriate license to avoid taint.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
* cleanup-clk-h-includes: (62 commits)
clk: Remove clk.h from clk-provider.h
clk: h8300: Remove clk.h and clkdev.h includes
clk: at91: Include clk.h and slab.h
clk: ti: Switch clk-provider.h include to clk.h
clk: pistachio: Include clk.h
clk: ingenic: Include clk.h
clk: si570: Include clk.h
clk: moxart: Include clk.h
clk: cdce925: Include clk.h
clk: Include clk.h in clk.c
clk: zynq: Include clk.h
clk: ti: Include clk.h
clk: sunxi: Include clk.h and remove unused clkdev.h includes
clk: st: Include clk.h
clk: qcom: Include clk.h
clk: highbank: Include clk.h
clk: bcm: Include clk.h
clk: versatile: Remove clk.h and clkdev.h includes
clk: ux500: Remove clk.h and clkdev.h includes
clk: tegra: Properly include clk.h
...
The other ce clocks have the flag set, but ce1 doesn't, so
clk_set_rate() doesn't propagate up the tree to the ce1_src_clk.
Set the flag as this is supported.
Reported-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Tested-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Fixes: 0282465320 ("clk: qcom: Add APQ8084 Global Clock Controller support")
Fixes: d33faa9ead ("clk: qcom: Add support for MSM8974's global clock controller (GCC)")
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Clock rates are stored in an unsigned long field, but ->determine_rate()
(which returns a rounded rate from a requested one) returns a long
value (errors are reported using negative error codes), which can lead
to long overflow if the clock rate exceed 2Ghz.
Change ->determine_rate() prototype to return 0 or an error code, and pass
a pointer to a clk_rate_request structure containing the expected target
rate and the rate constraints imposed by clk users.
The clk_rate_request structure might be extended in the future to contain
other kind of constraints like the rounding policy, the maximum clock
inaccuracy or other things that are not yet supported by the CCF
(power consumption constraints ?).
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
CC: Jonathan Corbet <corbet@lwn.net>
CC: Tony Lindgren <tony@atomide.com>
CC: Ralf Baechle <ralf@linux-mips.org>
CC: "Emilio López" <emilio@elopez.com.ar>
CC: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Tero Kristo <t-kristo@ti.com>
CC: Peter De Schrijver <pdeschrijver@nvidia.com>
CC: Prashant Gaikwad <pgaikwad@nvidia.com>
CC: Stephen Warren <swarren@wwwdotorg.org>
CC: Thierry Reding <thierry.reding@gmail.com>
CC: Alexandre Courbot <gnurou@gmail.com>
CC: linux-doc@vger.kernel.org
CC: linux-kernel@vger.kernel.org
CC: linux-arm-kernel@lists.infradead.org
CC: linux-omap@vger.kernel.org
CC: linux-mips@linux-mips.org
CC: linux-tegra@vger.kernel.org
[sboyd@codeaurora.org: Fix parent dereference problem in
__clk_determine_rate()]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Tested-by: Romain Perier <romain.perier@gmail.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
[sboyd@codeaurora.org: Folded in fix from Heiko for fixed-rate
clocks without parents or a rate determining op]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Add support for SR2 type pll operations. SR2 is optimized for Time Interval
Error (TIE) or absolute jitter.
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Make const both the array and the strings, so they can be
moved to .rodata section.
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Since the parent rate has been recalculated, pixel RCG clock
should rely on it to find the correct M/N values during set_rate,
instead of calling __clk_round_rate() to its parent again.
Signed-off-by: Hai Li <hali@codeaurora.org>
Tested-by: Archit Taneja <architt@codeaurora.org>
Fixes: 99cbd064b0 ("clk: qcom: Support display RCG clocks")
[sboyd@codeaurora.org: Silenced unused parent variable warning]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Add the NSS/GMAC clocks and the TCM clock and NSS resets.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The gfx3d_clk_src parents configuration is incorrect. Fix it.
Fixes: 3966fab8b6 "clk: qcom: Add MSM8916 Global Clock Controller support"
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
One of the video codec clock frequencies has incorrect divider
value. Fix it.
Fixes: 3966fab8b6 "clk: qcom: Add MSM8916 Global Clock Controller support"
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
When we introduced the parent_map tables, we missed to update
some of the functions where mapping is translated. Fix this.
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Tested-by: Nicolas Dechesne <nicolas.dechesne@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Support for Qualcomm's clock controllers should be available only
on Qualcomm platforms.
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The NAND controller within EBI2 requires EBI2_CLK and
EBI2_ALWAYS_ON_CLK clocks. Create structs for these clocks so
that they can be used by the NAND controller driver. Add an entry
for EBI2_AON_CLK in the gcc-ipq806x DT binding document.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
drivers/clk/qcom/clk-pll.c:74:1-4: WARNING: end returns can be simpified
Simplify a trivial if-return sequence. Possibly combine with a
preceding function call.
Generated by: scripts/coccinelle/misc/simple_return.cocci
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
These frequency tables list the wrong rates. Either they don't
have the correct frequency at all, or they're specified in kHz
instead of Hz. Fix it.
Fixes: c99e515a92 "clk: qcom: Add IPQ806X LPASS clock controller (LCC) driver"
Tested-by: Kenneth Westfield <kwestfie@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This patch adds support for the global clock controller found on the MSM8916
based devices. It allows the various device drivers to probe and control
their clocks and resets.
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
[sboyd@codeaurora.org: Removed NULL entry from parent_maps]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
In the current parent mapping code, we can get duplicate or inconsistent
indexes, which leads to discrepancy between the number of elements in the
array and the number of parents. Until now, this was solved with some
reordering but this is not always possible.
This patch introduces index tables that are used to define the relations
between the PLL source and the hardware mux configuration value.
To accomplish this, here we do the following:
- Define a parent_map struct to map the relations between PLL source index
and register configuration value.
- Add a qcom_find_src_index() function for finding the index of a clock
matching the specific PLL configuration.
- Update the {set,get}_parent RCG functions use the newly introduced
parent_map struct.
- Convert all existing drivers to the new parent_map tables.
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Currently configure_bank() returns void. Add some error
checking on the regmap calls and propagate if there is
any error.
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
According to the common clock framework API, the clk_get_parent() function
should return u8. Currently we are returning negative values on error. Fix
this and use the default parent in case of an error.
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Currently, a RCG's M/N counter (used for fraction division) is
set to either 'bypass' (counter disabled) or 'dual edge' (counter
enabled) based on whether the corresponding rcg struct has a mnd
field specified and a non-zero N.
In the case where M and N are the same value, the M/N counter is
still enabled by code even though no division takes place.
Leaving the RCG in such a state can result in improper behavior.
This was observed with the DSI pixel clock RCG when M and N were
both set to 1.
Add an additional check (M != N) to enable the M/N counter only
when it's needed for fraction division.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Fixes: bcd61c0f53 (clk: qcom: Add support for root clock
generators (RCGs))
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The ahbix clock can never be turned off in practice. To change the
rates we need to switch the mux off the M/N counter to an always on
source (XO), reprogram the M/N counter to get the rate we want and
finally switch back to the M/N counter. Add a new ops structure
for this type of clock so that we can set the rate properly.
Fixes: c99e515a92 "clk: qcom: Add IPQ806X LPASS clock controller (LCC) driver"
Tested-by: Kenneth Westfield <kwestfie@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
PXO is 25MHz, not 27MHz. Fix the table.
Fixes: 24d8fba44a "clk: qcom: Add support for IPQ8064's global
clock controller (GCC)"
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Reviewed-by: Andy Gross <agross@codeaurora.org>
Tested-by: Andy Gross <agross@codeaurora.org>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
drivers/clk/qcom/lcc-msm8960.c:577:3-8: No need to set .owner here. The core will do it.
Remove .owner field if calls are used which set it automatically
Generated by: scripts/coccinelle/api/platform_no_drv_owner.cocci
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
drivers/clk/qcom/lcc-ipq806x.c:465:3-8: No need to set .owner here. The core will do it.
Remove .owner field if calls are used which set it automatically
Generated by: scripts/coccinelle/api/platform_no_drv_owner.cocci
CC: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
This clock is needed for most audio clock frequencies. Add it.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
regmap_read() returns 0 on success, not the value of the register
that is read. Fix it so we properly detect the frequency plan.
Fixes: b82875ee07 "clk: qcom: Add MSM8960/APQ8064 LPASS clock
controller (LCC) driver"
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
These shifts were copy/pasted from the pcm which is a different
size RCG. Use the correct offsets so that slimbus rates are
correct.
Fixes: b82875ee07 "clk: qcom: Add MSM8960/APQ8064 LPASS clock controller (LCC) driver"
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
Adds a way for clock consumers to set maximum and minimum rates. This
can be used for thermal drivers to set minimum rates, or by misc.
drivers to set maximum rates to assure a minimum performance level.
Changes the signature of the determine_rate callback by adding the
parameters min_rate and max_rate.
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
[sboyd@codeaurora.org: set req_rate in __clk_init]
Signed-off-by: Michael Turquette <mturquette@linaro.org>
[mturquette@linaro.org: min/max rate for sun6i_ahb1_clk_determine_rate
migrated clk-private.h changes to clk.c]
Add an LCC driver for MSM8960/APQ8064 that supports the i2s,
slimbus, and pcm clocks.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Tested-by: Kenneth Westfield <kwestfie@codeaurora.org>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
Add an LCC driver for IPQ806x that supports the i2s, S/PDIF, and
pcm clocks.
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Kumar Gala <galak@codeaurora.org>
Signed-off-by: Josh Cartwright <joshc@codeaurora.org>
[sboyd@codeaurora.org: Reworded commit text, added Kconfig
select, fleshed out Kconfig description a bit more, added pll4
configuration and reworked probe for it, added muxes, split out
dt-binding file]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Tested-by: Kenneth Westfield <kwestfie@codeaurora.org>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
Add support for muxes that use regmap instead of readl/writel
directly. We don't support as many features as clk-mux.c, but
this is good enough to support getting and setting parents.
Adding a table based lookup can be added in the future if needed.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Tested-by: Kenneth Westfield <kwestfie@codeaurora.org>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
Add support for dividers that use regmap instead of readl/writel.
Signed-off-by: Josh Cartwright <joshc@codeaurora.org>
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
[sboyd@codeaurora.org: Switch to using generic divider code, drop
enable/disable, reword commit text]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Tested-by: Kenneth Westfield <kwestfie@codeaurora.org>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
much later than usual due to several last minute bugs that had to be
addressed. As usual the majority of changes are new drivers and
modifications to existing drivers. The core recieved many fixes along
with the groundwork for several large changes coming in the future which
will better parition clock providers from clock consumers.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=jD84
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus-3.19' of git://git.linaro.org/people/mike.turquette/linux
Pull clk framework updates from Mike Turquette:
"This is much later than usual due to several last minute bugs that had
to be addressed. As usual the majority of changes are new drivers and
modifications to existing drivers. The core recieved many fixes along
with the groundwork for several large changes coming in the future
which will better parition clock providers from clock consumers"
* tag 'clk-for-linus-3.19' of git://git.linaro.org/people/mike.turquette/linux: (86 commits)
clk: samsung: Fix Exynos 5420 pinctrl setup and clock disable failure due to domain being gated
ARM: OMAP3: clock: fix boot breakage in legacy mode
ARM: OMAP2+: clock: fix DPLL code to use new determine rate APIs
clk: Really fix deadlock with mmap_sem
clk: mmp: fix sparse non static symbol warning
clk: Change clk_ops->determine_rate to return a clk_hw as the best parent
clk: change clk_debugfs_add_file to take a struct clk_hw
clk: Don't expose __clk_get_accuracy
clk: Don't try to use a struct clk* after it could have been freed
clk: Remove unused function __clk_get_prepare_count
clk: samsung: Fix double add of syscore ops after driver rebind
clk: samsung: exynos4: set parent of sclk_hdmiphy to hdmi
clk: samsung: exynos4415: Fix build with PM_SLEEP disabled
clk: samsung: remove unnecessary inclusion of header files from clk.h
clk: samsung: remove unnecessary CONFIG_OF from clk.c
clk: samsung: Spelling s/bwtween/between/
clk: rockchip: Add support for the mmc clock phases using the framework
clk: rockchip: add bindings for the mmc clocks
clk: rockchip: rk3288 export i2s0_clkout for use in DT
clk: rockchip: use clock ID for DMC (memory controller) on rk3288
...
Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes, just
removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There are
some ath9k patches coming in through this tree that have been acked by
the wireless maintainers as they relied on the debugfs changes.
Everything has been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlSOD20ACgkQMUfUDdst+ylLPACg2QrW1oHhdTMT9WI8jihlHVRM
53kAoLeteByQ3iVwWurwwseRPiWa8+MI
=OVRS
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core update from Greg KH:
"Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes,
just removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There
are some ath9k patches coming in through this tree that have been
acked by the wireless maintainers as they relied on the debugfs
changes.
Everything has been in linux-next for a while"
* tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (324 commits)
Revert "ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries"
fs: debugfs: add forward declaration for struct device type
firmware class: Deletion of an unnecessary check before the function call "vunmap"
firmware loader: fix hung task warning dump
devcoredump: provide a one-way disable function
device: Add dev_<level>_once variants
ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries
ath: use seq_file api for ath9k debugfs files
debugfs: add helper function to create device related seq_file
drivers/base: cacheinfo: remove noisy error boot message
Revert "core: platform: add warning if driver has no owner"
drivers: base: support cpu cache information interface to userspace via sysfs
drivers: base: add cpu_device_create to support per-cpu devices
topology: replace custom attribute macros with standard DEVICE_ATTR*
cpumask: factor out show_cpumap into separate helper function
driver core: Fix unbalanced device reference in drivers_probe
driver core: fix race with userland in device_add()
sysfs/kernfs: make read requests on pre-alloc files use the buffer.
sysfs/kernfs: allow attributes to request write buffer be pre-allocated.
fs: sysfs: return EGBIG on write if offset is larger than file size
...
This is in preparation for clock providers to not have to deal with struct clk.
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
There is a duplication in a clock name for apq8084 platform that causes
the following warning: "RBCPR_CLK_SRC" redefined
Resolve this by adding a MMSS_ prefix to this clock and making its name
coherent with msm8974 platform.
Fixes: 2b46cd23a5 ("clk: qcom: Add APQ8084 Multimedia Clock Controller (MMCC) support")
Signed-off-by: Georgi Djakov <gdjakov@mm-sol.com>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
Some fixes for the IPQ driver and some code consolidation
and refactoring.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=fPIM
-----END PGP SIGNATURE-----
Merge tag 'qcom-clocks-for-3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/galak/linux-qcom into clk-next
qcom clock changes for 3.18
Some fixes for the IPQ driver and some code consolidation
and refactoring.
There is no need to init .owner field.
Based on the patch from Peter Griffin <peter.griffin@linaro.org>
"mmc: remove .owner field for drivers using module_platform_driver"
This patch removes the superflous .owner field for drivers which
use the module_platform_driver API, as this is overriden in
platform_driver_register anyway."
Signed-off-by: Kiran Padwal <kiran.padwal@smartplayin.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
The banked MD RCGs in global clock control have a different
register layout than the ones implemented in multimedia clock
control. Add support for these types of clocks so we can change
the rates of the UBI32 clocks.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
There are two find_freq() functions in clk-rcg.c and clk-rcg2.c
that are almost exactly the same. Consolidate them into one
function to save on some code space.
Cc: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
