When userspace executes a syscall or gets interrupted,
BEAR contains a kernel address when returning to userspace.
This make it pretty easy to figure out where the kernel is
mapped even with KASLR enabled. To fix this, add lpswe to
lowcore and always execute it there, so userspace sees only
the lowcore address of lpswe. For this we have to extend
both critical_cleanup and the SWITCH_ASYNC macro to also check
for lpswe addresses in lowcore.
Fixes: b2d24b97b2 ("s390/kernel: add support for kernel address space layout randomization (KASLR)")
Cc: <stable@vger.kernel.org> # v5.2+
Reviewed-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: Sven Schnelle <svens@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
It turned out that fake numa support is rather useless on s390, since
there are no scenarios where there is any performance or other benefit
when used.
However it does provide maintenance cost and breaks from time to time.
Therefore remove it.
CONFIG_NUMA is still supported with a very small backend and only one
node. This way userspace applications which require NUMA interfaces
continue to work.
Note that NODES_SHIFT is set to 1 (= 2 nodes) instead of 0 (= 1 node),
since there is quite a bit of kernel code which assumes that more than
one node is possible if CONFIG_NUMA is enabled.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Add the new kernel command line parameter 'dfltcc=' to configure s390
zlib hardware support.
Format: { on | off | def_only | inf_only | always }
on: s390 zlib hardware support for compression on
level 1 and decompression (default)
off: No s390 zlib hardware support
def_only: s390 zlib hardware support for deflate
only (compression on level 1)
inf_only: s390 zlib hardware support for inflate
only (decompression)
always: Same as 'on' but ignores the selected compression
level always using hardware support (used for debugging)
Link: http://lkml.kernel.org/r/20200103223334.20669-5-zaslonko@linux.ibm.com
Signed-off-by: Mikhail Zaslonko <zaslonko@linux.ibm.com>
Cc: Chris Mason <clm@fb.com>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: David Sterba <dsterba@suse.com>
Cc: Eduard Shishkin <edward6@linux.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Ilya Leoshkevich <iii@linux.ibm.com>
Cc: Josef Bacik <josef@toxicpanda.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
On the s390 platform memblock.physmem array is being built by directly
calling into memblock_add_range() which is a low level function not
intended to be used outside of memblock. Hence lets conditionally add
helper functions for physmem array when HAVE_MEMBLOCK_PHYS_MAP is
enabled. Also use MAX_NUMNODES instead of 0 as node ID similar to
memblock_add() and memblock_reserve(). Make memblock_add_range() a
static function as it is no longer getting used outside of memblock.
Link: http://lkml.kernel.org/r/1578283835-21969-1-git-send-email-anshuman.khandual@arm.com
Signed-off-by: Anshuman Khandual <anshuman.khandual@arm.com>
Reviewed-by: Mike Rapoport <rppt@linux.ibm.com>
Acked-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Vasily Gorbik <gor@linux.ibm.com>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Collin Walling <walling@linux.ibm.com>
Cc: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Cc: Philipp Rudo <prudo@linux.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Here are the big set of tty and serial driver updates for 5.6-rc1
Included in here are:
- dummy_con cleanups (touches lots of arch code)
- sysrq logic cleanups (touches lots of serial drivers)
- samsung driver fixes (wasn't really being built)
- conmakeshash move to tty subdir out of scripts
- lots of small tty/serial driver updates
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXjFRBg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yn2VACgkge7vTeUNeZFc+6F4NWphAQ5tCQAoK/MMbU6
0O8ef7PjFwCU4s227UTv
=6m40
-----END PGP SIGNATURE-----
Merge tag 'tty-5.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial driver updates from Greg KH:
"Here are the big set of tty and serial driver updates for 5.6-rc1
Included in here are:
- dummy_con cleanups (touches lots of arch code)
- sysrq logic cleanups (touches lots of serial drivers)
- samsung driver fixes (wasn't really being built)
- conmakeshash move to tty subdir out of scripts
- lots of small tty/serial driver updates
All of these have been in linux-next for a while with no reported
issues"
* tag 'tty-5.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (140 commits)
tty: n_hdlc: Use flexible-array member and struct_size() helper
tty: baudrate: SPARC supports few more baud rates
tty: baudrate: Synchronise baud_table[] and baud_bits[]
tty: serial: meson_uart: Add support for kernel debugger
serial: imx: fix a race condition in receive path
serial: 8250_bcm2835aux: Document struct bcm2835aux_data
serial: 8250_bcm2835aux: Use generic remapping code
serial: 8250_bcm2835aux: Allocate uart_8250_port on stack
serial: 8250_bcm2835aux: Suppress register_port error on -EPROBE_DEFER
serial: 8250_bcm2835aux: Suppress clk_get error on -EPROBE_DEFER
serial: 8250_bcm2835aux: Fix line mismatch on driver unbind
serial_core: Remove unused member in uart_port
vt: Correct comment documenting do_take_over_console()
vt: Delete comment referencing non-existent unbind_con_driver()
arch/xtensa/setup: Drop dummy_con initialization
arch/x86/setup: Drop dummy_con initialization
arch/unicore32/setup: Drop dummy_con initialization
arch/sparc/setup: Drop dummy_con initialization
arch/sh/setup: Drop dummy_con initialization
arch/s390/setup: Drop dummy_con initialization
...
con_init in tty/vt.c will now set conswitchp to dummy_con if it's unset.
Drop it from arch setup code.
Signed-off-by: Arvind Sankar <nivedita@alum.mit.edu>
Link: https://lore.kernel.org/r/20191218214506.49252-20-nivedita@alum.mit.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The new machine loader on z15 always creates an IPL Report block and
thus sets the IPL_PL_FLAG_IPLSR even when secure boot is disabled. This
causes the wrong message being printed at boot. Fix this by checking for
IPL_PL_FLAG_SIPL instead.
Fixes: 9641b8cc73 ("s390/ipl: read IPL report at early boot")
Signed-off-by: Philipp Rudo <prudo@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
CALL_ON_STACK is intended to be used for temporary stack switching with
potential return to the caller.
When CALL_ON_STACK is misused to switch from nodat stack to task stack
back_chain information would later lead stack unwinder from task stack into
(per cpu) nodat stack which is reused for other purposes. This would
yield confusing unwinding result or errors.
To avoid that introduce CALL_ON_STACK_NORETURN to be used instead. It
makes sure that back_chain is zeroed and unwinder finishes gracefully
ending up at task pt_regs.
Reviewed-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
- Add support for IBM z15 machines.
- Add SHA3 and CCA AES cipher key support in zcrypt and pkey refactoring.
- Move to arch_stack_walk infrastructure for the stack unwinder.
- Various kasan fixes and improvements.
- Various command line parsing fixes.
- Improve decompressor phase debuggability.
- Lift no bss usage restriction for the early code.
- Use refcount_t for reference counters for couple of places in
mm code.
- Logging improvements and return code fix in vfio-ccw code.
- Couple of zpci fixes and minor refactoring.
- Remove some outdated documentation.
- Fix secure boot detection.
- Other various minor code clean ups.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEE3QHqV+H2a8xAv27vjYWKoQLXFBgFAl1/pRoACgkQjYWKoQLX
FBjxLQf/Y1nlmoc8URLqaqfNTczIvUzdfXuahI7L75RoIIiqHtcHBrVwauSr7Lma
XVRzK/+6q0UPISrOIZEEtQKsMMM7rGuUv/+XTyrOB/Tsc31kN2EIRXltfXI/lkb8
BZdgch4Xs2rOD7y6TvqpYJsXYXsnLMWwCk8V+48V/pok4sEgMDgh0bTQRHPHYmZ6
1cv8ZQ0AeuVxC6ChM30LhajGRPkYd8RQ82K7fU7jxT0Tjzu66SyrW3pTwA5empBD
RI2yBZJ8EXwJyTCpvN8NKiBgihDs9oUZl61Dyq3j64Mb1OuNUhxXA/8jmtnGn0ok
O9vtImCWzExhjSMkvotuhHEC05nEEQ==
=LCgE
-----END PGP SIGNATURE-----
Merge tag 's390-5.4-1' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull s390 updates from Vasily Gorbik:
- Add support for IBM z15 machines.
- Add SHA3 and CCA AES cipher key support in zcrypt and pkey
refactoring.
- Move to arch_stack_walk infrastructure for the stack unwinder.
- Various kasan fixes and improvements.
- Various command line parsing fixes.
- Improve decompressor phase debuggability.
- Lift no bss usage restriction for the early code.
- Use refcount_t for reference counters for couple of places in mm
code.
- Logging improvements and return code fix in vfio-ccw code.
- Couple of zpci fixes and minor refactoring.
- Remove some outdated documentation.
- Fix secure boot detection.
- Other various minor code clean ups.
* tag 's390-5.4-1' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux: (48 commits)
s390: remove pointless drivers-y in drivers/s390/Makefile
s390/cpum_sf: Fix line length and format string
s390/pci: fix MSI message data
s390: add support for IBM z15 machines
s390/crypto: Support for SHA3 via CPACF (MSA6)
s390/startup: add pgm check info printing
s390/crypto: xts-aes-s390 fix extra run-time crypto self tests finding
vfio-ccw: fix error return code in vfio_ccw_sch_init()
s390: vfio-ap: fix warning reset not completed
s390/base: remove unused s390_base_mcck_handler
s390/sclp: Fix bit checked for has_sipl
s390/zcrypt: fix wrong handling of cca cipher keygenflags
s390/kasan: add kdump support
s390/setup: avoid using strncmp with hardcoded length
s390/sclp: avoid using strncmp with hardcoded length
s390/module: avoid using strncmp with hardcoded length
s390/pci: avoid using strncmp with hardcoded length
s390/kaslr: reserve memory for kasan usage
s390/mem_detect: provide single get_mem_detect_end
s390/cmma: reuse kstrtobool for option value parsing
...
Add detection for machine types 0x8562 and 8x8561 and set the ELF platform
name to z15. Add the miscellaneous-instruction-extension 3 facility to
the list of facilities for z15.
And allow to generate code that only runs on a z15 machine.
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Replace strncmp usage in console mode setup code with simple strcmp.
Replace strncmp which is used for prefix comparison with str_has_prefix.
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Few other crucial memory setup options are already handled in
the startup code. Those values are needed by kaslr and kasan
implementations. "vmalloc" is the last piece required for future
improvements such as early decision on kernel page levels depth required
for actual memory setup, as well as vmalloc memory area access monitoring
in kasan.
Reviewed-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
After some investigation it doesn't look like init_mm fields
start_code/end_code are used anywhere besides potentially in dump_mm for
debugging purposes. Originally the value of 0 for start_code reflected
the presence of lowcore and early boot code. But with kaslr in place
start_code/end_code range should not span over unoccupied by the code
segment memory. So, adjust init_mm start_code to point at the beginning
of the code segment like other architectures do it.
Acked-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
There never have been distributions that shiped with CONFIG_SMP=n for
s390. In addition the kernel currently doesn't even compile with
CONFIG_SMP=n for s390. Most likely it wouldn't even work, even if we
fix the compile error, since nobody tests it, since there is no use
case that I can think of.
Therefore simply enforce CONFIG_SMP and get rid of some more or
less unused code.
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Rework the dump_trace() stack unwinder interface to support different
unwinding algorithms. The new interface looks like this:
struct unwind_state state;
unwind_for_each_frame(&state, task, regs, start_stack)
do_something(state.sp, state.ip, state.reliable);
The unwind_bc.c file contains the implementation for the classic
back-chain unwinder.
One positive side effect of the new code is it now handles ftraced
functions gracefully. It prints the real name of the return function
instead of 'return_to_handler'.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
This patch adds support for relocating the kernel to a random address.
The random kernel offset is obtained from cpacf, using either TRNG, PRNO,
or KMC_PRNG, depending on supported MSA level.
KERNELOFFSET is added to vmcoreinfo, for crash --kaslr support.
Signed-off-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Reviewed-by: Philipp Rudo <prudo@linux.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
With a relocatable kernel that could reside at any place in memory, code
and data that has to stay below 2 GB needs special handling.
This patch introduces .dma sections for such text, data and ex_table.
The sections will be part of the decompressor kernel, so they will not
be relocated and stay below 2 GB. Their location is passed over to the
decompressed / relocated kernel via the .boot.preserved.data section.
The duald and aste for control register setup also need to stay below
2 GB, so move the setup code from arch/s390/kernel/head64.S to
arch/s390/boot/head.S. The duct and linkage_stack could reside above
2 GB, but their content has to be preserved for the decompresed kernel,
so they are also moved into the .dma section.
The start and end address of the .dma sections is added to vmcoreinfo,
for crash support, to help debugging in case the kernel crashed there.
Signed-off-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Reviewed-by: Philipp Rudo <prudo@linux.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The sccbs for init/read/sdias/early have to be located below 2 GB, and
they are currently defined as a static buffer.
With a relocatable kernel that could reside at any place in memory, this
will no longer guarantee the location below 2 GB, so use a dynamic
GFP_DMA allocation instead.
The sclp_early_sccb buffer needs special handling, as it can be used
very early, and by both the decompressor and also the decompressed
kernel. Therefore, a fixed 4 KB buffer is introduced at 0x11000, the
former PARMAREA_END. The new PARMAREA_END is now 0x12000, and it is
renamed to HEAD_END, as it is rather the end of head.S and not the end
of the parmarea.
Signed-off-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Reviewed-by: Philipp Rudo <prudo@linux.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Read the IPL Report block provided by secure-boot, add the entries
of the certificate list to the system key ring and print the list
of components.
PR: Adjust to Vasilys bootdata_preserved patch set. Preserve ipl_cert_list
for later use in kexec_file.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Philipp Rudo <prudo@linux.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The Ultravisor Call Facility (stfle bit 158) defines an API to the
Ultravisor (UV calls), a mini hypervisor located at machine
level. With help of the Ultravisor, KVM will be able to run
"protected" VMs, special VMs whose memory and management data are
unavailable to KVM.
The protected VMs can also request services from the Ultravisor.
The guest api consists of UV calls to share and unshare memory with the
kvm hypervisor.
To enable this feature support PROTECTED_VIRTUALIZATION_GUEST kconfig
option has been introduced.
Co-developed-by: Janosch Frank <frankja@de.ibm.com>
Signed-off-by: Janosch Frank <frankja@de.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Add check for the return value of memblock_alloc*() functions and call
panic() in case of error. The panic message repeats the one used by
panicing memblock allocators with adjustment of parameters to include
only relevant ones.
The replacement was mostly automated with semantic patches like the one
below with manual massaging of format strings.
@@
expression ptr, size, align;
@@
ptr = memblock_alloc(size, align);
+ if (!ptr)
+ panic("%s: Failed to allocate %lu bytes align=0x%lx\n", __func__, size, align);
[anders.roxell@linaro.org: use '%pa' with 'phys_addr_t' type]
Link: http://lkml.kernel.org/r/20190131161046.21886-1-anders.roxell@linaro.org
[rppt@linux.ibm.com: fix format strings for panics after memblock_alloc]
Link: http://lkml.kernel.org/r/1548950940-15145-1-git-send-email-rppt@linux.ibm.com
[rppt@linux.ibm.com: don't panic if the allocation in sparse_buffer_init fails]
Link: http://lkml.kernel.org/r/20190131074018.GD28876@rapoport-lnx
[akpm@linux-foundation.org: fix xtensa printk warning]
Link: http://lkml.kernel.org/r/1548057848-15136-20-git-send-email-rppt@linux.ibm.com
Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Signed-off-by: Anders Roxell <anders.roxell@linaro.org>
Reviewed-by: Guo Ren <ren_guo@c-sky.com> [c-sky]
Acked-by: Paul Burton <paul.burton@mips.com> [MIPS]
Acked-by: Heiko Carstens <heiko.carstens@de.ibm.com> [s390]
Reviewed-by: Juergen Gross <jgross@suse.com> [Xen]
Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org> [m68k]
Acked-by: Max Filippov <jcmvbkbc@gmail.com> [xtensa]
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Christophe Leroy <christophe.leroy@c-s.fr>
Cc: Christoph Hellwig <hch@lst.de>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Dennis Zhou <dennis@kernel.org>
Cc: Greentime Hu <green.hu@gmail.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Guan Xuetao <gxt@pku.edu.cn>
Cc: Guo Ren <guoren@kernel.org>
Cc: Mark Salter <msalter@redhat.com>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Petr Mladek <pmladek@suse.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Rich Felker <dalias@libc.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Rob Herring <robh@kernel.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Stafford Horne <shorne@gmail.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Make the memblock_phys_alloc() function an inline wrapper for
memblock_phys_alloc_range() and update the memblock_phys_alloc() callers
to check the returned value and panic in case of error.
Link: http://lkml.kernel.org/r/1548057848-15136-8-git-send-email-rppt@linux.ibm.com
Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Christophe Leroy <christophe.leroy@c-s.fr>
Cc: Christoph Hellwig <hch@lst.de>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Dennis Zhou <dennis@kernel.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Greentime Hu <green.hu@gmail.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Guan Xuetao <gxt@pku.edu.cn>
Cc: Guo Ren <guoren@kernel.org>
Cc: Guo Ren <ren_guo@c-sky.com> [c-sky]
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Juergen Gross <jgross@suse.com> [Xen]
Cc: Mark Salter <msalter@redhat.com>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Paul Burton <paul.burton@mips.com>
Cc: Petr Mladek <pmladek@suse.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Rich Felker <dalias@libc.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Rob Herring <robh@kernel.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Stafford Horne <shorne@gmail.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- A copy of Arnds compat wrapper generation series
- Pass information about the KVM guest to the host in form the control
program code and the control program version code
- Map IOV resources to support PCI physical functions on s390
- Add vector load and store alignment hints to improve performance
- Use the "jdd" constraint with gcc 9 to make jump labels working again
- Remove amode workaround for old z/VM releases from the DCSS code
- Add support for in-kernel performance measurements using the
CPU measurement counter facility
- Introduce a new PMU device cpum_cf_diag to capture counters and
store thenn as event raw data.
- Bug fixes and cleanups
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQEcBAABCAAGBQJcfh4QAAoJEDjwexyKj9rgXVAH/RzVbi3vznldujSNfCFTZKPu
EmFFAZIfbhifW3szfylyOJL52pFhxjcWzY0hkFEkbs2t90sn8l1BNkDscYZtfNHC
XvN3N9LsHyxOeyxvQuWLSio58qm+Lr1L0UrIhbMvqyAVkOLmIHvybFwi83OkMptm
djoL8NbuNsAA2s26y2bZLNtU7FmOW5smJIlnt7H4dmK4SFylqZKS/EnUZxGDgn+7
UrrTTOQUir0QZ8vraANsP1M0/LqPcd2YusLmj4jOdZ5Muc2Ch2AA991FofqdKShO
/8cGlsIzwHWGgdnP/YDea5gbetvonayYduixKy3EnYpWQ9iogiBjH4G7QNxcncs=
=v26J
-----END PGP SIGNATURE-----
Merge tag 's390-5.1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull s390 updates from Martin Schwidefsky:
- A copy of Arnds compat wrapper generation series
- Pass information about the KVM guest to the host in form the control
program code and the control program version code
- Map IOV resources to support PCI physical functions on s390
- Add vector load and store alignment hints to improve performance
- Use the "jdd" constraint with gcc 9 to make jump labels working again
- Remove amode workaround for old z/VM releases from the DCSS code
- Add support for in-kernel performance measurements using the CPU
measurement counter facility
- Introduce a new PMU device cpum_cf_diag to capture counters and store
thenn as event raw data.
- Bug fixes and cleanups
* tag 's390-5.1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux: (54 commits)
Revert "s390/cpum_cf: Add kernel message exaplanations"
s390/dasd: fix read device characteristic with CONFIG_VMAP_STACK=y
s390/suspend: fix prefix register reset in swsusp_arch_resume
s390: warn about clearing als implied facilities
s390: allow overriding facilities via command line
s390: clean up redundant facilities list setup
s390/als: remove duplicated in-place implementation of stfle
s390/cio: Use cpa range elsewhere within vfio-ccw
s390/cio: Fix vfio-ccw handling of recursive TICs
s390: vfio_ap: link the vfio_ap devices to the vfio_ap bus subsystem
s390/cpum_cf: Handle EBUSY return code from CPU counter facility reservation
s390/cpum_cf: Add kernel message exaplanations
s390/cpum_cf_diag: Add support for s390 counter facility diagnostic trace
s390/cpum_cf: add ctr_stcctm() function
s390/cpum_cf: move common functions into a separate file
s390/cpum_cf: introduce kernel_cpumcf_avail() function
s390/cpu_mf: replace stcctm5() with the stcctm() function
s390/cpu_mf: add store cpu counter multiple instruction support
s390/cpum_cf: Add minimal in-kernel interface for counter measurements
s390/cpum_cf: introduce kernel_cpumcf_alert() to obtain measurement alerts
...
The fix to make WARN work in the early boot code created a problem
on older machines without EDAT-1. The setup_lowcore_dat_on function
uses the pointer from lowcore_ptr[0] to set the DAT bit in the new
PSWs. That does not work if the kernel page table is set up with
4K pages as the prefix address maps to absolute zero.
To make this work the PSWs need to be changed with via address 0 in
form of the S390_lowcore definition.
Reported-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Cornelia Huck <cohuck@redhat.com>
Fixes: 94f85ed3e2f8 ("s390/setup: fix early warning messages")
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The setup_lowcore() function creates a new prefix page for the boot CPU.
The PSW mask for the system_call, external interrupt, i/o interrupt and
the program check handler have the DAT bit set in this new prefix page.
At the time setup_lowcore is called the system still runs without virtual
address translation, the paging_init() function creates the kernel page
table and loads the CR13 with the kernel ASCE.
Any code between setup_lowcore() and the end of paging_init() that has
a BUG or WARN statement will create a program check that can not be
handled correctly as there is no kernel page table yet.
To allow early WARN statements initially setup the lowcore with DAT off
and set the DAT bit only after paging_init() has completed.
Cc: stable@vger.kernel.org
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Remove including <linux/version.h> that don't need it.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The #ifdef CONFIG_DMA_API_DEBUG check in reserve_kernel() is no longer
needed, since commit ea535e418c ("dma-debug: switch check from _text
to _stext") changed the logic in lib/dma-debug.c, so remove it.
Reviewed-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The s390x diagnose 318 instruction sets the control program name code (CPNC)
and control program version code (CPVC) to provide useful information
regarding the OS during debugging. The CPNC is explicitly set to 4 to
indicate a Linux/KVM environment.
The CPVC is a 7-byte value containing:
- 3-byte Linux version code, currently set to 0
- 3-byte unique value, currently set to 0
- 1-byte trailing null
Signed-off-by: Collin Walling <walling@linux.ibm.com>
Acked-by: Janosch Frank <frankja@linux.ibm.com>
Acked-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Message-Id: <1544135405-22385-2-git-send-email-walling@linux.ibm.com>
[set version code to 0 until the structure is fully defined]
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Right now the early machine detection code check stsi 3.2.2 for "KVM"
and set MACHINE_IS_VM if this is different. As the console detection
uses diagnose 8 if MACHINE_IS_VM returns true this will crash Linux
early for any non z/VM system that sets a different value than KVM.
So instead of assuming z/VM, do not set any of MACHINE_IS_LPAR,
MACHINE_IS_VM, or MACHINE_IS_KVM.
CC: stable@vger.kernel.org
Reviewed-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Move remaining definitions and declarations from include/linux/bootmem.h
into include/linux/memblock.h and remove the redundant header.
The includes were replaced with the semantic patch below and then
semi-automated removal of duplicated '#include <linux/memblock.h>
@@
@@
- #include <linux/bootmem.h>
+ #include <linux/memblock.h>
[sfr@canb.auug.org.au: dma-direct: fix up for the removal of linux/bootmem.h]
Link: http://lkml.kernel.org/r/20181002185342.133d1680@canb.auug.org.au
[sfr@canb.auug.org.au: powerpc: fix up for removal of linux/bootmem.h]
Link: http://lkml.kernel.org/r/20181005161406.73ef8727@canb.auug.org.au
[sfr@canb.auug.org.au: x86/kaslr, ACPI/NUMA: fix for linux/bootmem.h removal]
Link: http://lkml.kernel.org/r/20181008190341.5e396491@canb.auug.org.au
Link: http://lkml.kernel.org/r/1536927045-23536-30-git-send-email-rppt@linux.vnet.ibm.com
Signed-off-by: Mike Rapoport <rppt@linux.vnet.ibm.com>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Chris Zankel <chris@zankel.net>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Greentime Hu <green.hu@gmail.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Guan Xuetao <gxt@pku.edu.cn>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "James E.J. Bottomley" <jejb@parisc-linux.org>
Cc: Jonas Bonn <jonas@southpole.se>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Ley Foon Tan <lftan@altera.com>
Cc: Mark Salter <msalter@redhat.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Palmer Dabbelt <palmer@sifive.com>
Cc: Paul Burton <paul.burton@mips.com>
Cc: Richard Kuo <rkuo@codeaurora.org>
Cc: Richard Weinberger <richard@nod.at>
Cc: Rich Felker <dalias@libc.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Serge Semin <fancer.lancer@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Make it explicit that the caller gets a physical address rather than a
virtual one.
This will also allow using meblock_alloc prefix for memblock allocations
returning virtual address, which is done in the following patches.
The conversion is done using the following semantic patch:
@@
expression e1, e2, e3;
@@
(
- memblock_alloc(e1, e2)
+ memblock_phys_alloc(e1, e2)
|
- memblock_alloc_nid(e1, e2, e3)
+ memblock_phys_alloc_nid(e1, e2, e3)
|
- memblock_alloc_try_nid(e1, e2, e3)
+ memblock_phys_alloc_try_nid(e1, e2, e3)
)
Link: http://lkml.kernel.org/r/1536927045-23536-7-git-send-email-rppt@linux.vnet.ibm.com
Signed-off-by: Mike Rapoport <rppt@linux.vnet.ibm.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Chris Zankel <chris@zankel.net>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Greentime Hu <green.hu@gmail.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Guan Xuetao <gxt@pku.edu.cn>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "James E.J. Bottomley" <jejb@parisc-linux.org>
Cc: Jonas Bonn <jonas@southpole.se>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Ley Foon Tan <lftan@altera.com>
Cc: Mark Salter <msalter@redhat.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Palmer Dabbelt <palmer@sifive.com>
Cc: Paul Burton <paul.burton@mips.com>
Cc: Richard Kuo <rkuo@codeaurora.org>
Cc: Richard Weinberger <richard@nod.at>
Cc: Rich Felker <dalias@libc.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Serge Semin <fancer.lancer@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
With the introduction of the module area on top of the vmalloc area, the
calculation of VMALLOC_START in setup_memory_end() function hasn't been
adjusted. As a result we got vmalloc area 2 Gb (MODULES_LEN) smaller than
it should be and the preceding vmemmap area got extra memory instead.
The patch fixes this calculation error although there were no visible
negative effects.
Apart from that, change 'tmp' variable to 'vmemmap' in memory_end
calculation for better readability.
Reviewed-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Mikhail Zaslonko <zaslonko@linux.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
By default 3-level paging is used when the kernel is compiled with
kasan support. Add 4-level paging option to support systems with more
then 3TB of physical memory and to cover 4-level paging specific code
with kasan as well.
Reviewed-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
To lower memory footprint and speed up kasan initialisation detect
EDAT availability and use large pages if possible. As we know how
much memory is needed for initialisation, another simplistic large
page allocator is introduced to avoid memory fragmentation.
Since facilities list is retrieved anyhow, detect noexec support and
adjust pages attributes. Handle noexec kernel option to avoid inconsistent
kasan shadow memory pages flags.
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Kasan needs 1/8 of kernel virtual address space to be reserved as the
shadow area. And eventually it requires the shadow memory offset to be
known at compile time (passed to the compiler when full instrumentation
is enabled). Any value picked as the shadow area offset for 3-level
paging would eat up identity mapping on 4-level paging (with 1PB
shadow area size). So, the kernel sticks to 3-level paging when kasan
is enabled. 3TB border is picked as the shadow offset. The memory
layout is adjusted so, that physical memory border does not exceed
KASAN_SHADOW_START and vmemmap does not go below KASAN_SHADOW_END.
Due to the fact that on s390 paging is set up very late and to cover
more code with kasan instrumentation, temporary identity mapping and
final shadow memory are set up early. The shadow memory mapping is
later carried over to init_mm.pgd during paging_init.
For the needs of paging structures allocation and shadow memory
population a primitive allocator is used, which simply chops off
memory blocks from the end of the physical memory.
Kasan currenty doesn't track vmemmap and vmalloc areas.
Current memory layout (for 3-level paging, 2GB physical memory).
---[ Identity Mapping ]---
0x0000000000000000-0x0000000000100000
---[ Kernel Image Start ]---
0x0000000000100000-0x0000000002b00000
---[ Kernel Image End ]---
0x0000000002b00000-0x0000000080000000 2G <- physical memory border
0x0000000080000000-0x0000030000000000 3070G PUD I
---[ Kasan Shadow Start ]---
0x0000030000000000-0x0000030010000000 256M PMD RW X <- shadow for 2G memory
0x0000030010000000-0x0000037ff0000000 523776M PTE RO NX <- kasan zero ro page
0x0000037ff0000000-0x0000038000000000 256M PMD RW X <- shadow for 2G modules
---[ Kasan Shadow End ]---
0x0000038000000000-0x000003d100000000 324G PUD I
---[ vmemmap Area ]---
0x000003d100000000-0x000003e080000000
---[ vmalloc Area ]---
0x000003e080000000-0x000003ff80000000
---[ Modules Area ]---
0x000003ff80000000-0x0000040000000000 2G
Acked-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
To distinguish zfcpdump case and to be able to parse some of the kernel
command line arguments early (e.g. mem=) ipl block retrieval and command
line construction code is moved to the early boot phase.
"memory_end" is set up correctly respecting "mem=" and hsa_size in case
of the zfcpdump.
arch/s390/boot/string.c is introduced to provide string handling and
command line parsing functions to early boot phase code for the compressed
kernel image case.
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Print mem_detect info source when memblock=debug is specified.
Reviewed-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Move memory detection to early boot phase. To store online memory
regions "struct mem_detect_info" has been introduced together with
for_each_mem_detect_block iterator. mem_detect_info is later converted
to memblock.
Also introduces sclp_early_get_meminfo function to get maximum physical
memory and maximum increment number.
Reviewed-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Reviewed-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Remove STACK_ORDER and STACK_SIZE in favour of identical THREAD_SIZE_ORDER
and THREAD_SIZE definitions. THREAD_SIZE and THREAD_SIZE_ORDER naming is
misleading since it is used as general kernel stack size information. But
both those definitions are used in the common code and throughout
architectures specific code, so changing the naming is problematic.
Reviewed-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
With virtually mapped kernel stacks the kernel stack overflow detection
is now fault based, every stack has a guard page in the vmalloc space.
The panic_stack is renamed to nodat_stack and is used for all function
that need to run without DAT, e.g. memcpy_real or do_start_kdump.
The main effect is a reduction in the kernel image size as with vmap
stacks the old style overflow checking that adds two instructions per
function is not needed anymore. Result from bloat-o-meter:
add/remove: 20/1 grow/shrink: 13/26854 up/down: 2198/-216240 (-214042)
In regard to performance the micro-benchmark for fork has a hit of a
few microseconds, allocating 4 pages in vmalloc space is more expensive
compare to an order-2 page allocation. But with real workload I could
not find a noticeable difference.
Acked-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Introduce PARMAREA_END, and use it for memblock reserve of low
memory, which is used for lowcore, kdump data mover code and page
buffer, early stack and parmarea. There is no need to reserve an
area between PARMAREA_END and the decompressor _ehead.
Reviewed-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Just add the new machine type number to the two places that matter.
Cc: <stable@vger.kernel.org> # v4.14+
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
With CONFIG_EXPOLINE_AUTO=y the call of spectre_v2_auto_early() via
early_initcall is done *after* the early_param functions. This
overwrites any settings done with the nobp/no_spectre_v2/spectre_v2
parameters. The code patching for the kernel is done after the
evaluation of the early parameters but before the early_initcall
is done. The end result is a kernel image that is patched correctly
but the kernel modules are not.
Make sure that the nospec auto detection function is called before the
early parameters are evaluated and before the code patching is done.
Fixes: 6e179d6412 ("s390: add automatic detection of the spectre defense")
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The S390 architecture does not support any graphics hardware,
but with the latest support for Virtio GPU in Linux and Virtio
GPU emulation in QEMU, it's possible to enable graphics for
S390 using the Virtio GPU device.
To enable display we need to enable the Linux Virtual Terminal (VT)
layer for S390. But the VT subsystem initializes quite early
at boot so we need a dummy console driver till the Virtio GPU
driver is initialized and we can run the framebuffer console.
The framebuffer console over a Virtio GPU device can be run
in combination with the serial SCLP console (default on S390).
The SCLP console can still be accessed by management applications
(eg: via Libvirt's virsh console).
Signed-off-by: Farhan Ali <alifm@linux.vnet.ibm.com>
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <e23b61f4f599ba23881727a1e8880e9d60cc6a48.1519315352.git.alifm@linux.vnet.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Common code defines linker symbols which denote sections start/end in
a form of char []. Referencing those symbols as _symbol or &_symbol
yields the same result, but "_symbol" form is more widespread across
newly written code. Convert s390 specific code to this style.
Also removes unused _text symbol definition in boot/compressed/misc.c.
Signed-off-by: Vasily Gorbik <gor@linux.vnet.ibm.com>
Acked-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Add CONFIG_EXPOLINE to enable the use of the new -mindirect-branch= and
-mfunction_return= compiler options to create a kernel fortified against
the specte v2 attack.
With CONFIG_EXPOLINE=y all indirect branches will be issued with an
execute type instruction. For z10 or newer the EXRL instruction will
be used, for older machines the EX instruction. The typical indirect
call
basr %r14,%r1
is replaced with a PC relative call to a new thunk
brasl %r14,__s390x_indirect_jump_r1
The thunk contains the EXRL/EX instruction to the indirect branch
__s390x_indirect_jump_r1:
exrl 0,0f
j .
0: br %r1
The detour via the execute type instruction has a performance impact.
To get rid of the detour the new kernel parameter "nospectre_v2" and
"spectre_v2=[on,off,auto]" can be used. If the parameter is specified
the kernel and module code will be patched at runtime.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
To be able to switch off specific CPU alternatives with kernel parameters
make a copy of the facility bit mask provided by STFLE and use the copy
for the decision to apply an alternative.
Reviewed-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
It's good to have SPDX identifiers in all files to make it easier to
audit the kernel tree for correct licenses.
Update the arch/s390/kernel/ files with the correct SPDX license
identifier based on the license text in the file itself. The SPDX
identifier is a legally binding shorthand, which can be used instead of
the full boiler plate text.
This work is based on a script and data from Thomas Gleixner, Philippe
Ombredanne, and Kate Stewart.
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Kate Stewart <kstewart@linuxfoundation.org>
Cc: Philippe Ombredanne <pombredanne@nexb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
