Add SPDX license identifiers to all files which:
- Have no license information of any form
- Have EXPORT_.*_SYMBOL_GPL inside which was used in the
initial scan/conversion to ignore the file
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull networking updates from David Miller:
"Highlights:
1) Support AES128-CCM ciphers in kTLS, from Vakul Garg.
2) Add fib_sync_mem to control the amount of dirty memory we allow to
queue up between synchronize RCU calls, from David Ahern.
3) Make flow classifier more lockless, from Vlad Buslov.
4) Add PHY downshift support to aquantia driver, from Heiner
Kallweit.
5) Add SKB cache for TCP rx and tx, from Eric Dumazet. This reduces
contention on SLAB spinlocks in heavy RPC workloads.
6) Partial GSO offload support in XFRM, from Boris Pismenny.
7) Add fast link down support to ethtool, from Heiner Kallweit.
8) Use siphash for IP ID generator, from Eric Dumazet.
9) Pull nexthops even further out from ipv4/ipv6 routes and FIB
entries, from David Ahern.
10) Move skb->xmit_more into a per-cpu variable, from Florian
Westphal.
11) Improve eBPF verifier speed and increase maximum program size,
from Alexei Starovoitov.
12) Eliminate per-bucket spinlocks in rhashtable, and instead use bit
spinlocks. From Neil Brown.
13) Allow tunneling with GUE encap in ipvs, from Jacky Hu.
14) Improve link partner cap detection in generic PHY code, from
Heiner Kallweit.
15) Add layer 2 encap support to bpf_skb_adjust_room(), from Alan
Maguire.
16) Remove SKB list implementation assumptions in SCTP, your's truly.
17) Various cleanups, optimizations, and simplifications in r8169
driver. From Heiner Kallweit.
18) Add memory accounting on TX and RX path of SCTP, from Xin Long.
19) Switch PHY drivers over to use dynamic featue detection, from
Heiner Kallweit.
20) Support flow steering without masking in dpaa2-eth, from Ioana
Ciocoi.
21) Implement ndo_get_devlink_port in netdevsim driver, from Jiri
Pirko.
22) Increase the strict parsing of current and future netlink
attributes, also export such policies to userspace. From Johannes
Berg.
23) Allow DSA tag drivers to be modular, from Andrew Lunn.
24) Remove legacy DSA probing support, also from Andrew Lunn.
25) Allow ll_temac driver to be used on non-x86 platforms, from Esben
Haabendal.
26) Add a generic tracepoint for TX queue timeouts to ease debugging,
from Cong Wang.
27) More indirect call optimizations, from Paolo Abeni"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1763 commits)
cxgb4: Fix error path in cxgb4_init_module
net: phy: improve pause mode reporting in phy_print_status
dt-bindings: net: Fix a typo in the phy-mode list for ethernet bindings
net: macb: Change interrupt and napi enable order in open
net: ll_temac: Improve error message on error IRQ
net/sched: remove block pointer from common offload structure
net: ethernet: support of_get_mac_address new ERR_PTR error
net: usb: smsc: fix warning reported by kbuild test robot
staging: octeon-ethernet: Fix of_get_mac_address ERR_PTR check
net: dsa: support of_get_mac_address new ERR_PTR error
net: dsa: sja1105: Fix status initialization in sja1105_get_ethtool_stats
vrf: sit mtu should not be updated when vrf netdev is the link
net: dsa: Fix error cleanup path in dsa_init_module
l2tp: Fix possible NULL pointer dereference
taprio: add null check on sched_nest to avoid potential null pointer dereference
net: mvpp2: cls: fix less than zero check on a u32 variable
net_sched: sch_fq: handle non connected flows
net_sched: sch_fq: do not assume EDT packets are ordered
net: hns3: use devm_kcalloc when allocating desc_cb
net: hns3: some cleanup for struct hns3_enet_ring
...
Pull timer updates from Ingo Molnar:
"This cycle had the following changes:
- Timer tracing improvements (Anna-Maria Gleixner)
- Continued tasklet reduction work: remove the hrtimer_tasklet
(Thomas Gleixner)
- Fix CPU hotplug remove race in the tick-broadcast mask handling
code (Thomas Gleixner)
- Force upper bound for setting CLOCK_REALTIME, to fix ABI
inconsistencies with handling values that are close to the maximum
supported and the vagueness of when uptime related wraparound might
occur. Make the consistent maximum the year 2232 across all
relevant ABIs and APIs. (Thomas Gleixner)
- various cleanups and smaller fixes"
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
tick: Fix typos in comments
tick/broadcast: Fix warning about undefined tick_broadcast_oneshot_offline()
timekeeping: Force upper bound for setting CLOCK_REALTIME
timer/trace: Improve timer tracing
timer/trace: Replace deprecated vsprintf pointer extension %pf by %ps
timer: Move trace point to get proper index
tick/sched: Update tick_sched struct documentation
tick: Remove outgoing CPU from broadcast masks
timekeeping: Consistently use unsigned int for seqcount snapshot
softirq: Remove tasklet_hrtimer
xfrm: Replace hrtimer tasklet with softirq hrtimer
mac80211_hwsim: Replace hrtimer tasklet with softirq hrtimer
None of them have any external callers, make them static.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
This structure is now only 4 bytes, so its more efficient
to cache a copy rather than its address.
No significant size difference in allmodconfig vmlinux.
With non-modular kernel that has all XFRM options enabled, this
series reduces vmlinux image size by ~11kb. All xfrm_mode
indirections are gone and all modes are built-in.
before (ipsec-next master):
text data bss dec filename
21071494 7233140 11104324 39408958 vmlinux.master
after this series:
21066448 7226772 11104324 39397544 vmlinux.patched
With allmodconfig kernel, the size increase is only 362 bytes,
even all the xfrm config options removed in this series are
modular.
before:
text data bss dec filename
15731286 6936912 4046908 26715106 vmlinux.master
after this series:
15731492 6937068 4046908 26715468 vmlinux
Signed-off-by: Florian Westphal <fw@strlen.de>
Reviewed-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
after previous changes, xfrm_mode contains no function pointers anymore
and all modules defining such struct contain no code except an init/exit
functions to register the xfrm_mode struct with the xfrm core.
Just place the xfrm modes core and remove the modules,
the run-time xfrm_mode register/unregister functionality is removed.
Before:
text data bss dec filename
7523 200 2364 10087 net/xfrm/xfrm_input.o
40003 628 440 41071 net/xfrm/xfrm_state.o
15730338 6937080 4046908 26714326 vmlinux
7389 200 2364 9953 net/xfrm/xfrm_input.o
40574 656 440 41670 net/xfrm/xfrm_state.o
15730084 6937068 4046908 26714060 vmlinux
The xfrm*_mode_{transport,tunnel,beet} modules are gone.
v2: replace CONFIG_INET6_XFRM_MODE_* IS_ENABLED guards with CONFIG_IPV6
ones rather than removing them.
Signed-off-by: Florian Westphal <fw@strlen.de>
Reviewed-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Adds an EXPORT_SYMBOL for afinfo_get_rcu, as it will now be called from
ipv6 in case of CONFIG_IPV6=m.
This change has virtually no effect on vmlinux size, but it reduces
afinfo size and allows followup patch to make xfrm modes const.
v2: mark if (afinfo) tests as likely (Sabrina)
re-fetch afinfo according to inner_mode in xfrm_prepare_input().
Signed-off-by: Florian Westphal <fw@strlen.de>
Reviewed-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
This will be useful to know if we're supposed to decode ipv4 or ipv6.
While at it, make the unregister function return void, all module_exit
functions did just BUG(); there is never a point in doing error checks
if there is no way to handle such error.
Signed-off-by: Florian Westphal <fw@strlen.de>
Reviewed-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
In commit 6a53b75932 ("xfrm: check id proto in validate_tmpl()")
I introduced a check for xfrm protocol, but according to Herbert
IPSEC_PROTO_ANY should only be used as a wildcard for lookup, so
it should be removed from validate_tmpl().
And, IPSEC_PROTO_ANY is expected to only match 3 IPSec-specific
protocols, this is why xfrm_state_flush() could still miss
IPPROTO_ROUTING, which leads that those entries are left in
net->xfrm.state_all before exit net. Fix this by replacing
IPSEC_PROTO_ANY with zero.
This patch also extracts the check from validate_tmpl() to
xfrm_id_proto_valid() and uses it in parse_ipsecrequest().
With this, no other protocols should be added into xfrm.
Fixes: 6a53b75932 ("xfrm: check id proto in validate_tmpl()")
Reported-by: syzbot+0bf0519d6e0de15914fe@syzkaller.appspotmail.com
Cc: Steffen Klassert <steffen.klassert@secunet.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Switch the timer to HRTIMER_MODE_SOFT, which executed the timer
callback in softirq context and remove the hrtimer_tasklet.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Anna-Maria Gleixner <anna-maria@linutronix.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: David S. Miller <davem@davemloft.net>
Cc: netdev@vger.kernel.org
Cc: Steffen Klassert <steffen.klassert@secunet.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Link: https://lkml.kernel.org/r/20190301224821.29843-3-bigeasy@linutronix.de
xfrm_state_put() moves struct xfrm_state to the GC list
and schedules the GC work to clean it up. On net exit call
path, xfrm_state_flush() is called to clean up and
xfrm_flush_gc() is called to wait for the GC work to complete
before exit.
However, this doesn't work because one of the ->destructor(),
ipcomp_destroy(), schedules the same GC work again inside
the GC work. It is hard to wait for such a nested async
callback. This is also why syzbot still reports the following
warning:
WARNING: CPU: 1 PID: 33 at net/ipv6/xfrm6_tunnel.c:351 xfrm6_tunnel_net_exit+0x2cb/0x500 net/ipv6/xfrm6_tunnel.c:351
...
ops_exit_list.isra.0+0xb0/0x160 net/core/net_namespace.c:153
cleanup_net+0x51d/0xb10 net/core/net_namespace.c:551
process_one_work+0xd0c/0x1ce0 kernel/workqueue.c:2153
worker_thread+0x143/0x14a0 kernel/workqueue.c:2296
kthread+0x357/0x430 kernel/kthread.c:246
ret_from_fork+0x3a/0x50 arch/x86/entry/entry_64.S:352
In fact, it is perfectly fine to bypass GC and destroy xfrm_state
synchronously on net exit call path, because it is in process context
and doesn't need a work struct to do any blocking work.
This patch introduces xfrm_state_put_sync() which simply bypasses
GC, and lets its callers to decide whether to use this synchronous
version. On net exit path, xfrm_state_fini() and
xfrm6_tunnel_net_exit() use it. And, as ipcomp_destroy() itself is
blocking, it can use xfrm_state_put_sync() directly too.
Also rename xfrm_state_gc_destroy() to ___xfrm_state_destroy() to
reflect this change.
Fixes: b48c05ab5d ("xfrm: Fix warning in xfrm6_tunnel_net_exit.")
Reported-and-tested-by: syzbot+e9aebef558e3ed673934@syzkaller.appspotmail.com
Cc: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Steffen Klassert says:
====================
pull request (net): ipsec 2018-12-18
1) Fix error return code in xfrm_output_one()
when no dst_entry is attached to the skb.
From Wei Yongjun.
2) The xfrm state hash bucket count reported to
userspace is off by one. Fix from Benjamin Poirier.
3) Fix NULL pointer dereference in xfrm_input when
skb_dst_force clears the dst_entry.
4) Fix freeing of xfrm states on acquire. We use a
dedicated slab cache for the xfrm states now,
so free it properly with kmem_cache_free.
From Mathias Krause.
Please pull or let me know if there are problems.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 565f0fa902 ("xfrm: use a dedicated slab cache for struct
xfrm_state") moved xfrm state objects to use their own slab cache.
However, it missed to adapt xfrm_user to use this new cache when
freeing xfrm states.
Fix this by introducing and make use of a new helper for freeing
xfrm_state objects.
Fixes: 565f0fa902 ("xfrm: use a dedicated slab cache for struct xfrm_state")
Reported-by: Pan Bian <bianpan2016@163.com>
Cc: <stable@vger.kernel.org> # v4.18+
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
sadhcnt is reported by `ip -s xfrm state count` as "buckets count", not the
hash mask.
Fixes: 28d8909bc7 ("[XFRM]: Export SAD info.")
Signed-off-by: Benjamin Poirier <bpoirier@suse.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Now that in_compat_syscall() is consistent on all architectures and does
not longer report true on native i686, the workarounds (ifdeffery and
helpers) can be removed.
Signed-off-by: Dmitry Safonov <dima@arista.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Dmitry Safonov <0x7f454c46@gmail.com>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Andy Lutomirsky <luto@kernel.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: John Stultz <john.stultz@linaro.org>
Cc: "Kirill A. Shutemov" <kirill.shutemov@linux.intel.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Steffen Klassert <steffen.klassert@secunet.com>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: linux-efi@vger.kernel.org
Cc: netdev@vger.kernel.org
Link: https://lkml.kernel.org/r/20181012134253.23266-3-dima@arista.com
Allow attaching an SA to an xfrm interface id after
the creation of the SA, so that tasks such as keying
which must be done as the SA is created, can remain
separate from the decision on how to route traffic
from an SA. This permits SA creation to be decomposed
in to three separate steps:
1) allocation of a SPI
2) algorithm and key negotiation
3) insertion into the data path
Signed-off-by: Nathan Harold <nharold@google.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
In order to remove performance impact of having the extra u32 in every
single flowi, this change removes the flowi_xfrm struct, prefering to
take the if_id as a method parameter where needed.
In the inbound direction, if_id is only needed during the
__xfrm_check_policy() function, and the if_id can be determined at that
point based on the skb. As such, xfrmi_decode_session() is only called
with the skb in __xfrm_check_policy().
In the outbound direction, the only place where if_id is needed is the
xfrm_lookup() call in xfrmi_xmit2(). With this change, the if_id is
directly passed into the xfrm_lookup_with_ifid() call. All existing
callers can still call xfrm_lookup(), which uses a default if_id of 0.
This change does not change any behavior of XFRMIs except for improving
overall system performance via flowi size reduction.
This change has been tested against the Android Kernel Networking Tests:
https://android.googlesource.com/kernel/tests/+/master/net/test
Signed-off-by: Benedict Wong <benedictwong@google.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
The lifetime managment uses '__u64' timestamps on the user space
interface, but 'unsigned long' for reading the current time in the kernel
with get_seconds().
While this is probably safe beyond y2038, it will still overflow in 2106,
and the get_seconds() call is deprecated because fo that.
This changes the xfrm time handling to use time64_t consistently, along
with reading the time using the safer ktime_get_real_seconds(). It still
suffers from problems that can happen from a concurrent settimeofday()
call or (to a lesser degree) a leap second update, but since the time
stamps are part of the user API, there is nothing we can do to prevent
that.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Allow UPDSA to change "set mark" to permit
policy separation of packet routing decisions from
SA keying in systems that use mark-based routing.
The set mark, used as a routing and firewall mark
for outbound packets, is made update-able which
allows routing decisions to be handled independently
of keying/SA creation. To maintain consistency with
other optional attributes, the set mark is only
updated if sent with a non-zero value.
The per-SA lock and the xfrm_state_lock are taken in
that order to avoid a deadlock with
xfrm_timer_handler(), which also takes the locks in
that order.
Signed-off-by: Nathan Harold <nharold@google.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Kristian Evensen says:
In a project I am involved in, we are running ipsec (Strongswan) on
different mt7621-based routers. Each router is configured as an
initiator and has around ~30 tunnels to different responders (running
on misc. devices). Before the flow cache was removed (kernel 4.9), we
got a combined throughput of around 70Mbit/s for all tunnels on one
router. However, we recently switched to kernel 4.14 (4.14.48), and
the total throughput is somewhere around 57Mbit/s (best-case). I.e., a
drop of around 20%. Reverting the flow cache removal restores, as
expected, performance levels to that of kernel 4.9.
When pcpu xdst exists, it has to be validated first before it can be
used.
A negative hit thus increases cost vs. no-cache.
As number of tunnels increases, hit rate decreases so this pcpu caching
isn't a viable strategy.
Furthermore, the xdst cache also needs to run with BH off, so when
removing this the bh disable/enable pairs can be removed too.
Kristian tested a 4.14.y backport of this change and reported
increased performance:
In our tests, the throughput reduction has been reduced from around -20%
to -5%. We also see that the overall throughput is independent of the
number of tunnels, while before the throughput was reduced as the number
of tunnels increased.
Reported-by: Kristian Evensen <kristian.evensen@gmail.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
This patch adds the xfrm interface id as a lookup key
for xfrm states and policies. With this we can assign
states and policies to virtual xfrm interfaces.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Acked-by: Shannon Nelson <shannon.nelson@oracle.com>
Acked-by: Benedict Wong <benedictwong@google.com>
Tested-by: Benedict Wong <benedictwong@google.com>
Tested-by: Antony Antony <antony@phenome.org>
Reviewed-by: Eyal Birger <eyal.birger@gmail.com>
The bpf syscall and selftests conflicts were trivial
overlapping changes.
The r8169 change involved moving the added mdelay from 'net' into a
different function.
A TLS close bug fix overlapped with the splitting of the TLS state
into separate TX and RX parts. I just expanded the tests in the bug
fix from "ctx->conf == X" into "ctx->tx_conf == X && ctx->rx_conf
== X".
Signed-off-by: David S. Miller <davem@davemloft.net>
struct xfrm_state is rather large (768 bytes here) and therefore wastes
quite a lot of memory as it falls into the kmalloc-1024 slab cache,
leaving 256 bytes of unused memory per XFRM state object -- a net waste
of 25%.
Using a dedicated slab cache for struct xfrm_state reduces the level of
internal fragmentation to a minimum.
On my configuration SLUB chooses to create a slab cache covering 4
pages holding 21 objects, resulting in an average memory waste of ~13
bytes per object -- a net waste of only 1.6%.
In my tests this led to memory savings of roughly 2.3MB for 10k XFRM
states.
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
We need to make sure that all states are really deleted
before we check that the state lists are empty. Otherwise
we trigger a warning.
Fixes: baeb0dbbb5 ("xfrm6_tunnel: exit_net cleanup check added")
Reported-and-tested-by:syzbot+777bf170a89e7b326405@syzkaller.appspotmail.com
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
We don't have a compat layer for xfrm, so userspace and kernel
structures have different sizes in this case. This results in
a broken configuration, so refuse to configure socket policies
when trying to insert from 32 bit userspace as we do it already
with policies inserted via netlink.
Reported-and-tested-by: syzbot+e1a1577ca8bcb47b769a@syzkaller.appspotmail.com
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Assign true or false to boolean variables instead of an integer value.
This issue was detected with the help of Coccinelle.
Fixes: ffdb5211da ("xfrm: Auto-load xfrm offload modules")
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Current code configures the hardware with a new SA before the state has been
fully initialized. During this time interval, an incoming ESP packet can cause
a crash due to a NULL dereference. More specifically, xfrm_input() considers
the packet as valid, and yet, anti-replay mechanism is not initialized.
Move hardware configuration to the end of xfrm_state_construct(), and mark
the state as valid once the SA is fully initialized.
Fixes: d77e38e612 ("xfrm: Add an IPsec hardware offloading API")
Signed-off-by: Aviad Yehezkel <aviadye@mellnaox.com>
Signed-off-by: Aviv Heller <avivh@mellanox.com>
Signed-off-by: Yossi Kuperman <yossiku@mellanox.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
request_module can sleep, thus we cannot hold rcu_read_lock() while
calling it. The function also jumps back and takes rcu_read_lock()
again (in xfrm_state_get_afinfo()), resulting in an imbalance.
This codepath is triggered whenever a new offloaded state is created.
Fixes: ffdb5211da ("xfrm: Auto-load xfrm offload modules")
Reported-by: syzbot+ca425f44816d749e8eb49755567a75ee48cf4a30@syzkaller.appspotmail.com
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Currently we allow state updates to competely replace the contents
of x->encap. This is bad because on the user side ESP only sets up
header lengths depending on encap_type once when the state is first
created. This could result in the header lengths getting out of
sync with the actual state configuration.
In practice key managers will never do a state update to change the
encapsulation type. Only the port numbers need to be changed as the
peer NAT entry is updated.
Therefore this patch adds a check in xfrm_state_update to forbid
any changes to the encap_type.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
net/ipv6/ip6_gre.c is a case of parallel adds.
include/trace/events/tcp.h is a little bit more tricky. The removal
of in-trace-macro ifdefs in 'net' paralleled with moving
show_tcp_state_name and friends over to include/trace/events/sock.h
in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Steffen Klassert says:
====================
pull request (net): ipsec 2017-12-22
1) Check for valid id proto in validate_tmpl(), otherwise
we may trigger a warning in xfrm_state_fini().
From Cong Wang.
2) Fix a typo on XFRMA_OUTPUT_MARK policy attribute.
From Michal Kubecek.
3) Verify the state is valid when encap_type < 0,
otherwise we may crash on IPsec GRO .
From Aviv Heller.
4) Fix stack-out-of-bounds read on socket policy lookup.
We access the flowi of the wrong address family in the
IPv4 mapped IPv6 case, fix this by catching address
family missmatches before we do the lookup.
5) fix xfrm_do_migrate() with AEAD to copy the geniv
field too. Otherwise the state is not fully initialized
and migration fails. From Antony Antony.
6) Fix stack-out-of-bounds with misconfigured transport
mode policies. Our policy template validation is not
strict enough. It is possible to configure policies
with transport mode template where the address family
of the template does not match the selectors address
family. Fix this by refusing such a configuration,
address family can not change on transport mode.
7) Fix a policy reference leak when reusing pcpu xdst
entry. From Florian Westphal.
8) Reinject transport-mode packets through tasklet,
otherwise it is possible to reate a recursion
loop. From Herbert Xu.
Please pull or let me know if there are problems.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
copy geniv when cloning the xfrm state.
x->geniv was not copied to the new state and migration would fail.
xfrm_do_migrate
..
xfrm_state_clone()
..
..
esp_init_aead()
crypto_alloc_aead()
crypto_alloc_tfm()
crypto_find_alg() return EAGAIN and failed
Signed-off-by: Antony Antony <antony@phenome.org>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Currently it is possible to add or update socket policies, but
not clear them. Therefore, once a socket policy has been applied,
the socket cannot be used for unencrypted traffic.
This patch allows (privileged) users to clear socket policies by
passing in a NULL pointer and zero length argument to the
{IP,IPV6}_{IPSEC,XFRM}_POLICY setsockopts. This results in both
the incoming and outgoing policies being cleared.
The simple approach taken in this patch cannot clear socket
policies in only one direction. If desired this could be added
in the future, for example by continuing to pass in a length of
zero (which currently is guaranteed to return EMSGSIZE) and
making the policy be a pointer to an integer that contains one
of the XFRM_POLICY_{IN,OUT} enum values.
An alternative would have been to interpret the length as a
signed integer and use XFRM_POLICY_IN (i.e., 0) to clear the
input policy and -XFRM_POLICY_OUT (i.e., -1) to clear the output
policy.
Tested: https://android-review.googlesource.com/539816
Signed-off-by: Lorenzo Colitti <lorenzo@google.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
If a socket has a valid dst cache, then xfrm_lookup_route will get
skipped. However, the cache is not invalidated when applying policy to a
socket (i.e. IPV6_XFRM_POLICY). The result is that new policies are
sometimes ignored on those sockets. (Note: This was broken for IPv4 and
IPv6 at different times.)
This can be demonstrated like so,
1. Create UDP socket.
2. connect() the socket.
3. Apply an outbound XFRM policy to the socket. (setsockopt)
4. send() data on the socket.
Packets will continue to be sent in the clear instead of matching an
xfrm or returning a no-match error (EAGAIN). This affects calls to
send() and not sendto().
Invalidating the sk_dst_cache is necessary to correctly apply xfrm
policies. Since we do this in xfrm_user_policy(), the sk_lock was
already acquired in either do_ip_setsockopt() or do_ipv6_setsockopt(),
and we may call __sk_dst_reset().
Performance impact should be negligible, since this code is only called
when changing xfrm policy, and only affects the socket in question.
Fixes: 00bc0ef588 ("ipv6: Skip XFRM lookup if dst_entry in socket cache is valid")
Tested: https://android-review.googlesource.com/517555
Tested: https://android-review.googlesource.com/418659
Signed-off-by: Jonathan Basseri <misterikkit@google.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
I might be wrong but it doesn't look like xfrm_state_lock is required
for xfrm_policy_cache_flush and calling it under this lock triggers both
"sleeping function called from invalid context" and "possible circular
locking dependency detected" warnings on flush.
Fixes: ec30d78c14 xfrm: add xdst pcpu cache
Signed-off-by: Artem Savkov <asavkov@redhat.com>
Acked-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Creating sub policy that matches the same outer flow as main policy does
leads to a null pointer dereference if the outer mode's family is ipv4.
For userspace compatibility, this patch just eliminates the crash i.e.,
does not introduce any new sorting rule, which would fruitlessly affect
all but the aforementioned case.
Signed-off-by: Koichiro Den <den@klaipeden.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
IPSec crypto offload depends on the protocol-specific
offload module (such as esp_offload.ko).
When the user installs an SA with crypto-offload, load
the offload module automatically, in the same way
that the protocol module is loaded (such as esp.ko)
Signed-off-by: Ilan Tayari <ilant@mellanox.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
retain last used xfrm_dst in a pcpu cache.
On next request, reuse this dst if the policies are the same.
The cache will not help with strict RR workloads as there is no hit.
The cache packet-path part is reasonably small, the notifier part is
needed so we do not add long hangs when a device is dismantled but some
pcpu xdst still holds a reference, there are also calls to the flush
operation when userspace deletes SAs so modules can be removed
(there is no hit.
We need to run the dst_release on the correct cpu to avoid races with
packet path. This is done by adding a work_struct for each cpu and then
doing the actual test/release on each affected cpu via schedule_work_on().
Test results using 4 network namespaces and null encryption:
ns1 ns2 -> ns3 -> ns4
netperf -> xfrm/null enc -> xfrm/null dec -> netserver
what TCP_STREAM UDP_STREAM UDP_RR
Flow cache: 14644.61 294.35 327231.64
No flow cache: 14349.81 242.64 202301.72
Pcpu cache: 14629.70 292.21 205595.22
UDP tests used 64byte packets, tests ran for one minute each,
value is average over ten iterations.
'Flow cache' is 'net-next', 'No flow cache' is net-next plus this
series but without this patch.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
refcount_t type and corresponding API should be
used instead of atomic_t when the variable is used as
a reference counter. This allows to avoid accidental
refcounter overflows that might lead to use-after-free
situations.
Signed-off-by: Elena Reshetova <elena.reshetova@intel.com>
Signed-off-by: Hans Liljestrand <ishkamiel@gmail.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David Windsor <dwindsor@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Steffen Klassert says:
====================
pull request (net-next): ipsec-next 2017-06-23
1) Use memdup_user to spmlify xfrm_user_policy.
From Geliang Tang.
2) Make xfrm_dev_register static to silence a sparse warning.
From Wei Yongjun.
3) Use crypto_memneq to check the ICV in the AH protocol.
From Sabrina Dubroca.
4) Remove some unused variables in esp6.
From Stephen Hemminger.
5) Extend XFRM MIGRATE to allow to change the UDP encapsulation port.
From Antony Antony.
6) Include the UDP encapsulation port to km_migrate announcements.
From Antony Antony.
Please pull or let me know if there are problems.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add XFRMA_ENCAP, UDP encapsulation port, to km_migrate announcement
to userland. Only add if XFRMA_ENCAP was in user migrate request.
Signed-off-by: Antony Antony <antony@phenome.org>
Reviewed-by: Richard Guy Briggs <rgb@tricolour.ca>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Add UDP encapsulation port to XFRM_MSG_MIGRATE using an optional
netlink attribute XFRMA_ENCAP.
The devices that support IKE MOBIKE extension (RFC-4555 Section 3.8)
could go to sleep for a few minutes and wake up. When it wake up the
NAT mapping could have expired, the device send a MOBIKE UPDATE_SA
message to migrate the IPsec SA. The change could be a change UDP
encapsulation port, IP address, or both.
Reported-by: Paul Wouters <pwouters@redhat.com>
Signed-off-by: Antony Antony <antony@phenome.org>
Reviewed-by: Richard Guy Briggs <rgb@tricolour.ca>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
During xfrm migration copy replay and preplay sequence numbers
from the previous state.
Here is a tcpdump output showing the problem.
10.0.10.46 is running vanilla kernel, is the IKE/IPsec responder.
After the migration it sent wrong sequence number, reset to 1.
The migration is from 10.0.0.52 to 10.0.0.53.
IP 10.0.0.52.4500 > 10.0.10.46.4500: UDP-encap: ESP(spi=0x43ef462d,seq=0x7cf), length 136
IP 10.0.10.46.4500 > 10.0.0.52.4500: UDP-encap: ESP(spi=0xca1c282d,seq=0x7cf), length 136
IP 10.0.0.52.4500 > 10.0.10.46.4500: UDP-encap: ESP(spi=0x43ef462d,seq=0x7d0), length 136
IP 10.0.10.46.4500 > 10.0.0.52.4500: UDP-encap: ESP(spi=0xca1c282d,seq=0x7d0), length 136
IP 10.0.0.53.4500 > 10.0.10.46.4500: NONESP-encap: isakmp: child_sa inf2[I]
IP 10.0.10.46.4500 > 10.0.0.53.4500: NONESP-encap: isakmp: child_sa inf2[R]
IP 10.0.0.53.4500 > 10.0.10.46.4500: NONESP-encap: isakmp: child_sa inf2[I]
IP 10.0.10.46.4500 > 10.0.0.53.4500: NONESP-encap: isakmp: child_sa inf2[R]
IP 10.0.0.53.4500 > 10.0.10.46.4500: UDP-encap: ESP(spi=0x43ef462d,seq=0x7d1), length 136
NOTE: next sequence is wrong 0x1
IP 10.0.10.46.4500 > 10.0.0.53.4500: UDP-encap: ESP(spi=0xca1c282d,seq=0x1), length 136
IP 10.0.0.53.4500 > 10.0.10.46.4500: UDP-encap: ESP(spi=0x43ef462d,seq=0x7d2), length 136
IP 10.0.10.46.4500 > 10.0.0.53.4500: UDP-encap: ESP(spi=0xca1c282d,seq=0x2), length 136
Signed-off-by: Antony Antony <antony@phenome.org>
Reviewed-by: Richard Guy Briggs <rgb@tricolour.ca>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Use memdup_user() helper instead of open-coding to simplify the code.
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
This patch adds all the bits that are needed to do
IPsec hardware offload for IPsec states and ESP packets.
We add xfrmdev_ops to the net_device. xfrmdev_ops has
function pointers that are needed to manage the xfrm
states in the hardware and to do a per packet
offloading decision.
Joint work with:
Ilan Tayari <ilant@mellanox.com>
Guy Shapiro <guysh@mellanox.com>
Yossi Kuperman <yossiku@mellanox.com>
Signed-off-by: Guy Shapiro <guysh@mellanox.com>
Signed-off-by: Ilan Tayari <ilant@mellanox.com>
Signed-off-by: Yossi Kuperman <yossiku@mellanox.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
