Since in an NPI/DSA setup, not all ports will have the same MTU, we need
to make sure the watermarks for pause frames and/or tail dropping logic
that existed in the driver is still coherent for the new MTU values.
We need to do this because the NPI (aka external CPU) port needs an
increased MTU for the DSA tag. This will be done in a future patch.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It doesn't make sense to rewrite all these registers every time the PHY
library notifies us about a link state change.
In a future patch we will customize the MTU for the CPU port, and since
the MTU was previously configured from adjust_link, if we don't make
this change, its value would have got overridden.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The adjust_link routine should be generic enough to be (re)used by
any SoC that integrates a switch core compatible with the Ocelot
core switch driver. Currently all configurations are generic except
for the PCS settings that are SoC specific. Move these out to the
Ocelot SoC/board instance.
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Let's make this ioremap and regmap init code common. It should not
be platform dependent as it should be usable by PCI devices too.
Use better names where necessary to avoid clashes.
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
VSC7514 is a 10-port switch with 2 extra "CPU ports" (targets in the
queuing subsystem for terminating traffic locally).
There are 2 issues with hardcoding the CPU port as #10:
- It is not clear which snippets of the code are configuring something
for one of the CPU ports, and which snippets are just doing something
related to the number of physical ports.
- Actually any physical port can act as a CPU port connected to an
external CPU (in addition to the local CPU). This is called NPI mode
(Node Processor Interface) and is the way that the 6-port VSC9959
(Felix) switch is integrated inside NXP LS1028A (the "local management
CPU" functionality is not used there).
This patch makes it clear that the ocelot_bridge_stp_state_set function
operates on the CPU port (by making it an implicit member of the
bridging domain), and at the same time adds logic for the NPI port (aka
a physical port) to play the role of a CPU port (it shouldn't be part of
bridge_fwd_mask, as it's not explicitly enslaved to a bridge).
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that the places that configure routing destinations for the CPU port
have been marked as such, allow callers to specify their own CPU port
that is different than ocelot->num_phys_ports. A user will be the Felix
DSA driver, where the CPU port is one of the physical ports (NPI mode).
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This will be called from the Felix DSA frontend, which will work in
PHYLIB compatibility mode initially.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is just common path code that belongs to ocelot_init,
it has nothing to do with a specific SoC/board instance.
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow these functions to be called from the .port_enable and
.port_disable callbacks of DSA.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need a function for the DSA front-end that does none of the
net_device registration, but initializes the hardware ports.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The VSC7514 switch (Ocelot) is a 10-port device, while VSC9959 (Felix)
is 6-port. Therefore the VLAN filtering mask would be out of bounds when
calling for this new switch. Fix that.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert them into an implementation that can be called from DSA as well.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ocelot and ocelot_port structures will be used by a new DSA driver,
so the ocelot_board.c file will have to allocate and work with a private
structure (ocelot_port_private), which embeds the generic struct
ocelot_port. This is because in DSA, at least one interface does not
have a net_device, and the DSA driver API does not interact with that
anyway.
The ocelot_port structure is equivalent to dsa_port, and ocelot to
dsa_switch. The members of ocelot_port which have an equivalent in
dsa_port (such as dp->vlan_filtering) have been moved to
ocelot_port_private.
We want to enforce the coding convention that "ocelot_port" refers to
the structure, and "port" refers to the integer index. One can retrieve
the structure at any time from ocelot->ports[port].
The patch is large but only contains variable renaming and mechanical
movement of fields from one structure to another.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ocelot_port structure has a net_device embedded in it, which makes
it unsuitable for leaving it in the driver implementation functions.
Leave ocelot_flower.c untouched. In that file, ocelot_port is used as an
interface to the tc shared blocks. That will be addressed in the next
patch.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is needed so that the Felix DSA front-end can call the Ocelot
implementations.
The implementation of the "mc_disabled" switchdev attribute has also
been simplified by using the read-modify-write macro instead of
open-coding that operation.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is needed in order to present a simpler prototype to the DSA
front-end of ocelot.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To be able to implement a DSA front-end over ocelot_fdb_add,
ocelot_fdb_del, ocelot_fdb_dump, these need to have a simple function
prototype that is independent of struct net_device, netlink skb, etc.
So rename the ndo ops of the ocelot driver into
ocelot_port_fdb_{add,del,dump}, and have them all call the abstract
implementations. At the same time, refactor ocelot_port_fdb_do_dump into
a function whose prototype is compatible with dsa_fdb_dump_cb_t, so that
the do_dump implementations can live together and be called by the
ocelot_fdb_dump through a function pointer.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need an implementation of these functions that is agnostic to the
higher layer (switchdev or dsa).
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch transforms the ocelot_vlan_port_apply function ("apply
what?") into 3 standalone functions:
- ocelot_port_vlan_filtering
- ocelot_port_set_native_vlan
- ocelot_port_set_pvid
These functions have a prototype that is better aligned to the DSA API.
The function also had some static initialization (TPID, drop frames with
multicast source MAC) which was not being changed from any place, so
that was just moved to ocelot_probe_port (one of the 6 callers of
ocelot_vlan_port_apply).
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
One conflict in the BPF samples Makefile, some fixes in 'net' whilst
we were converting over to Makefile.target rules in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
The "read-modify-write register index" function is declared with a
confusing prototype: the "mask" and "reg" arguments are swapped.
Fortunately, this does not affect callers so far. Both arguments are
u32, and the wrapper macros (ocelot_rmw_ix etc) have the arguments in
the correct order (the one from ocelot_io.c).
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
lag_upper_info may be NULL on slave removal.
Fixes: dc96ee3730 ("net: mscc: ocelot: add bonding support")
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The check that the event is actually for this device should be moved
from the "port" handler to the net device handler.
Otherwise the port handler will deny bonding configuration for other
net devices in the same system (like enetc in the LS1028A) that don't
have the lag_upper_info->tx_type restriction that ocelot has.
Fixes: dc96ee3730 ("net: mscc: ocelot: add bonding support")
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before this change of_get_phy_mode() returned an enum,
phy_interface_t. On error, -ENODEV etc, is returned. If the result of
the function is stored in a variable of type phy_interface_t, and the
compiler has decided to represent this as an unsigned int, comparision
with -ENODEV etc, is a signed vs unsigned comparision.
Fix this problem by changing the API. Make the function return an
error, or 0 on success, and pass a pointer, of type phy_interface_t,
where the phy mode should be stored.
v2:
Return with *interface set to PHY_INTERFACE_MODE_NA on error.
Add error checks to all users of of_get_phy_mode()
Fixup a few reverse christmas tree errors
Fixup a few slightly malformed reverse christmas trees
v3:
Fix 0-day reported errors.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The switch driver keeps a "vid" variable per port, which signifies _the_
VLAN ID that is stripped on that port's egress (aka the native VLAN on a
trunk port).
That is the way the hardware is designed (mostly). The port->vid is
programmed into REW:PORT:PORT_VLAN_CFG:PORT_VID and the rewriter is told
to send all traffic as tagged except the one having port->vid.
There exists a possibility of finer-grained egress untagging decisions:
using the VCAP IS1 engine, one rule can be added to match every
VLAN-tagged frame whose VLAN should be untagged, and set POP_CNT=1 as
action. However, the IS1 can hold at most 512 entries, and the VLANs are
in the order of 6 * 4096.
So the code is fine for now. But this sequence of commands:
$ bridge vlan add dev swp0 vid 1 pvid untagged
$ bridge vlan add dev swp0 vid 2 untagged
makes untagged and pvid-tagged traffic be sent out of swp0 as tagged
with VID 1, despite user's request.
Prevent that from happening. The user should temporarily remove the
existing untagged VLAN (1 in this case), add it back as tagged, and then
add the new untagged VLAN (2 in this case).
Cc: Antoine Tenart <antoine.tenart@bootlin.com>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Fixes: 7142529f16 ("net: mscc: ocelot: add VLAN filtering")
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Background information: the driver operates the hardware in a mode where
a single VLAN can be transmitted as untagged on a particular egress
port. That is the "native VLAN on trunk port" use case. Its value is
held in port->vid.
Consider the following command sequence (no network manager, all
interfaces are down, debugging prints added by me):
$ ip link add dev br0 type bridge vlan_filtering 1
$ ip link set dev swp0 master br0
Kernel code path during last command:
br_add_slave -> ocelot_netdevice_port_event (NETDEV_CHANGEUPPER):
[ 21.401901] ocelot_vlan_port_apply: port 0 vlan aware 0 pvid 0 vid 0
br_add_slave -> nbp_vlan_init -> switchdev_port_attr_set -> ocelot_port_attr_set (SWITCHDEV_ATTR_ID_BRIDGE_VLAN_FILTERING):
[ 21.413335] ocelot_vlan_port_apply: port 0 vlan aware 1 pvid 0 vid 0
br_add_slave -> nbp_vlan_init -> nbp_vlan_add -> br_switchdev_port_vlan_add -> switchdev_port_obj_add -> ocelot_port_obj_add -> ocelot_vlan_vid_add
[ 21.667421] ocelot_vlan_port_apply: port 0 vlan aware 1 pvid 1 vid 1
So far so good. The bridge has replaced the driver's default pvid used
in standalone mode (0) with its own default_pvid (1). The port's vid
(native VLAN) has also changed from 0 to 1.
$ ip link set dev swp0 up
[ 31.722956] 8021q: adding VLAN 0 to HW filter on device swp0
do_setlink -> dev_change_flags -> vlan_vid_add -> ocelot_vlan_rx_add_vid -> ocelot_vlan_vid_add:
[ 31.728700] ocelot_vlan_port_apply: port 0 vlan aware 1 pvid 1 vid 0
The 8021q module uses the .ndo_vlan_rx_add_vid API on .ndo_open to make
ports be able to transmit and receive 802.1p-tagged traffic by default.
This API is supposed to offload a VLAN sub-interface, which for a switch
port means to add a VLAN that is not a pvid, and tagged on egress.
But the driver implementation of .ndo_vlan_rx_add_vid is wrong: it adds
back vid 0 as "egress untagged". Now back to the initial paragraph:
there is a single untagged VID that the driver keeps track of, and that
has just changed from 1 (the pvid) to 0. So this breaks the bridge
core's expectation, because it has changed vid 1 from untagged to
tagged, when what the user sees is.
$ bridge vlan
port vlan ids
swp0 1 PVID Egress Untagged
br0 1 PVID Egress Untagged
But curiously, instead of manifesting itself as "untagged and
pvid-tagged traffic gets sent as tagged on egress", the bug:
- is hidden when vlan_filtering=0
- manifests as dropped traffic when vlan_filtering=1, due to this setting:
if (port->vlan_aware && !port->vid)
/* If port is vlan-aware and tagged, drop untagged and priority
* tagged frames.
*/
val |= ANA_PORT_DROP_CFG_DROP_UNTAGGED_ENA |
ANA_PORT_DROP_CFG_DROP_PRIO_S_TAGGED_ENA |
ANA_PORT_DROP_CFG_DROP_PRIO_C_TAGGED_ENA;
which would have made sense if it weren't for this bug. The setting's
intention was "this is a trunk port with no native VLAN, so don't accept
untagged traffic". So the driver was never expecting to set VLAN 0 as
the value of the native VLAN, 0 was just encoding for "invalid".
So the fix is to not send 802.1p traffic as untagged, because that would
change the port's native vlan to 0, unbeknownst to the bridge, and
trigger unexpected code paths in the driver.
Cc: Antoine Tenart <antoine.tenart@bootlin.com>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Fixes: 7142529f16 ("net: mscc: ocelot: add VLAN filtering")
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
of_node_put needs to be called when the device node which is got
from of_get_child_by_name finished using.
In both cases of success and failure, we need to release 'ports',
so clean up the code using goto.
fixes: a556c76adc ("net: mscc: Add initial Ocelot switch support")
Signed-off-by: Wen Yang <wenyang@linux.alibaba.com>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Microchip Linux Driver Support <UNGLinuxDriver@microchip.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
The trap action should be copying the frame to CPU and
dropping it for forwarding, but current setting was just
copying frame to CPU.
Fixes: b596229448 ("net: mscc: ocelot: Add support for tcam")
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Acked-by: Allan W. Nielsen <allan.nielsen@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tc transparently maps the software priority number to hardware. Update
it to pass the major priority which is what most drivers expect. Update
drivers too so they do not need to lshift the priority field of the
flow_cls_common_offload object. The stmmac driver is an exception, since
this code assumes the tc software priority is fine, therefore, lshift it
just to be conservative.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for PTP Hardware Clock (PHC) to the Ocelot
switch for both PTP 1-step and 2-step modes.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In struct frame_info, the cpuq member is never used. This cosmetic patch
removes it from the structure, and from the parsing of the frame header
as it's only set but never used.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This cosmetic patch improves the frame header parsing readability by
introducing a new macro to access and mask its fields.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for using the PTP register range, and adds a
description of its registers. This bank is used when configuring PTP.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure the delayed work for stats update is not pending before
wq destruction.
This fixes the module unload path.
The issue is there since day 1.
Fixes: a556c76adc ("net: mscc: Add initial Ocelot switch support")
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This object stores the flow block callbacks that are attached to this
block. Update flow_block_cb_lookup() to take this new object.
This patch restores the block sharing feature.
Fixes: da3eeb904f ("net: flow_offload: add list handling functions")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename this type definition and adapt users.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
No need to annotate the netns on the flow block callback object,
flow_block_cb_is_busy() already checks for used blocks.
Fixes: d63db30c85 ("net: flow_offload: add flow_block_cb_alloc() and flow_block_cb_free()")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Each iteration of for_each_available_child_of_node puts the previous
node, but in the case of a return from the middle of the loop, there is
no put, thus causing a memory leak. Hence add an of_node_put before the
return in two places.
Issue found with Coccinelle.
Signed-off-by: Nishka Dasgupta <nishkadg.linux@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
And any other existing fields in this structure that refer to tc.
Specifically:
* tc_cls_flower_offload_flow_rule() to flow_cls_offload_flow_rule().
* TC_CLSFLOWER_* to FLOW_CLS_*.
* tc_cls_common_offload to tc_cls_common_offload.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a function to check if flow block callback is already in
use. Call this new function from flow_block_cb_setup_simple() and from
drivers.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch updates flow_block_cb_setup_simple() to use the flow block API.
Several drivers are also adjusted to use it.
This patch introduces the per-driver list of flow blocks to account for
blocks that are already in use.
Remove tc_block_offload alias.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename from TCF_BLOCK_BINDER_TYPE_* to FLOW_BLOCK_BINDER_TYPE_* and
remove temporary tcf_block_binder_type alias.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename from TC_BLOCK_{UN}BIND to FLOW_BLOCK_{UN}BIND and remove
temporary tc_block_command alias.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/ethernet/mscc/ocelot_ace.c: In function ‘vcap_cmd’:
drivers/net/ethernet/mscc/ocelot_ace.c:108:6: warning: variable ‘rc’ set
but not used [-Wunused-but-set-variable]
int rc;
^
It's never used since introduction in commit b596229448 ("net: mscc:
ocelot: Add support for tcam")
Signed-off-by: Mao Wenan <maowenan@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix sparse warning:
drivers/net/ethernet/mscc/ocelot_ace.c:96:3:
warning: symbol 'vcap_data_t' was not declared. Should it be static?
'vcap_data_t' never used so can be removed
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clang warns:
drivers/net/ethernet/mscc/ocelot_ace.c:335:37: warning: suggest braces
around initialization of subobject [-Wmissing-braces]
struct ocelot_vcap_u64 payload = { 0 };
^
{}
drivers/net/ethernet/mscc/ocelot_ace.c:336:28: warning: suggest braces
around initialization of subobject [-Wmissing-braces]
struct vcap_data data = { 0 };
^
{}
drivers/net/ethernet/mscc/ocelot_ace.c:683:37: warning: suggest braces
around initialization of subobject [-Wmissing-braces]
struct ocelot_ace_rule del_ace = { 0 };
^
{}
drivers/net/ethernet/mscc/ocelot_ace.c:743:28: warning: suggest braces
around initialization of subobject [-Wmissing-braces]
struct vcap_data data = { 0 };
^
{}
4 warnings generated.
One way to fix these warnings is to add additional braces like Clang
suggests; however, there has been a bit of push back from some
maintainers[1][2], who just prefer memset as it is unambiguous, doesn't
depend on a particular compiler version[3], and properly initializes all
subobjects. Do that here so there are no more warnings.
[1]: https://lore.kernel.org/lkml/022e41c0-8465-dc7a-a45c-64187ecd9684@amd.com/
[2]: https://lore.kernel.org/lkml/20181128.215241.702406654469517539.davem@davemloft.net/
[3]: https://lore.kernel.org/lkml/20181116150432.2408a075@redhat.com/
Fixes: b596229448 ("net: mscc: ocelot: Add support for tcam")
Link: https://github.com/ClangBuiltLinux/linux/issues/505
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hardware offload of port filtering are now supported via tc command using
flower filter. ACL rules are used to enable the hardware offload.
The following keys are supported:
vlan_id
vlan_prio
dst_mac/src_mac for non IP frames
dst_ip/src_ip
dst_port/src_port
The following actions are supported:
trap
drop
These filters are supported only on the ingress schedulare.
Add:
tc qdisc add dev eth3 ingress
tc filter ad dev eth3 parent ffff: ip_proto ip flower \
ip_proto tcp dst_port 80 action drop
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add ACL support using the TCAM. Using ACL it is possible to create rules
in hardware to filter/redirect frames.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
