Switch from DT specific of_property_* API to generic and more
modern device_property_* API.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
In certain designs, it is possible to add a battery on a populated i2c
bus without an sbs compliant charger. In that case, the battery will
unnecessarily and sometimes undesirably master the bus trying to write
info in the charger.
It is observed in many occasion that these battery "broadcasts" are even
corrupting other ongoing master to slave communication. I.e. the
multi-master support in the battery is inadequate.
Thankfully, the CHARGER_MODE bit allows designers to disable that SBS
battery behaviour.
This needs to be done once when the battery is first seen on the bus.
Signed-off-by: Jean-Francois Dagenais <jeff.dagenais@gmail.com>
[rebased code]
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
A battery, that is neither charged, nor discharged is not
always Full. If the charger is disabled for other reasons
it might simply be idle and should be marked accordingly.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Add support for reporting the SBS battery's condition flag
to userspace using the new "Calibration required" health status.
Reviewed-by: Emil Velikov <emil.velikov@collabora.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Expose the battery's manufacture date to userspace.
Reviewed-by: Emil Velikov <emil.velikov@collabora.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Expose maximum charge current/voltage information requested
by the battery.
Reviewed-by: Emil Velikov <emil.velikov@collabora.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
This reads the battery chemistry from the battery chip instead
of incorrectly hardcoding the type to be Li-Ion.
Reviewed-by: Emil Velikov <emil.velikov@collabora.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Expose averaged current information, which is part of the SBS
standard and should be supported by all batteries.
Reviewed-by: Emil Velikov <emil.velikov@collabora.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
SBS batteries optionally have support for PEC. This enables
PEC handling based on the implemented SBS version as suggested
by the standard. The support for PEC is re-evaluated when the
battery is hotplugged into the system, since there might be
systems supporting batteries from different SBS generations.
Reviewed-by: Emil Velikov <emil.velikov@collabora.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The SBS battery implements SMBus block reads. Currently the
driver "emulates" this by doing an I2C byte read for the
length followed by an I2C block read. The I2C subsystem
actually provides a proper API for doing SMBus block reads,
which can and should be used instead. The current implementation
does not properly handle packet error checking (PEC).
This change requires, that I2C bus drivers support I2C_M_RECV_LEN
or directly provide the SMBus API to access device manufacturer
and model name.
Reviewed-by: Emil Velikov <emil.velikov@collabora.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Add support for reporting the MaxError register from
battery fuel gauges following the smart battery standard.
Reviewed-by: Emil Velikov <emil.velikov@collabora.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Add support for BQ20Z65 manufacturer data to the sbs-battery
driver. Implementation has been verified using the public TRM
available from [0] and tested using a GE Flex 3S2P battery.
[0] http://www.ti.com/lit/pdf/sluu386
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Some battery fuel gauges know when the battery needs to
be recalibrated before providing usable values. This
should be reported via the health property.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Some smart batteries store their manufacture date, which is
useful to identify the battery and/or to know about the cell
quality.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Fix the following sparse warning:
drivers/power/supply/bd99954-charger.c:1028:6: warning: symbol 'bd9995x_chip_reset' was not declared.
The bd9995x_chip_reset() has only one call site within bd99954-charger.c
It should be static
Fixes: 0902f83664 ("power: supply: Support ROHM bd99954 charger")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Samuel Zou <zou_wei@huawei.com>
Reviewed-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Add device tree compatible strings and create proper modalias structures
to let this driver load automatically if compiled as module, because
max14577 MFD driver creates MFD cells with such compatible strings.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
-----BEGIN PGP SIGNATURE-----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=89mP
-----END PGP SIGNATURE-----
Merge tag 'tags/ib-mfd-iio-power-v5.8' into psy-next
This merges the MP2629 battery charge management immutable branch
between MFD, IIO and power-supply due for the v5.8 merge window
into power-supply for-next branch.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The mp2629 provides switching-mode battery charge management for
single-cell Li-ion or Li-polymer battery. Driver supports the
access/control input source and battery charging parameters.
Signed-off-by: Saravanan Sekar <sravanhome@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Move away from the deprecated API in this comment.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Report REG00.IINLIM value as INPUT_CURRENT_LIMIT property.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Report charging type based on recently read state.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Edge interrupts from the charger may be lost or stuck in fault mode
since probe(). Check if something changed everytime userspace wants
some data.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Datasheet describes two modes for reading ADC measurements:
1. continuous, 1 Hz - enabled and started by CONV_RATE bit
2. one-shot - triggered by CONV_START bit
In continuous mode, CONV_START is read-only and signifies an ongoing
conversion.
Change the code to follow the datasheet and really disable continuous
mode for power saving.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Charge Current is more apropriately reflected by CURRENT_NOW property
(measured current) than CONSTANT_CURRENT_VOLTAGE (configured CC-phase
current limit). Fix the reference and make the sign reflect direction
of the current.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
According to the datasheet available at (1), the bottom four
bits are always zero and the actual voltage is 1.25x this value
in mV. Since the kernel API specifies that voltages should be in
uV, it should report 1250x the shifted value.
1) https://datasheets.maximintegrated.com/en/ds/MAX17040-MAX17041.pdf
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The framework is unhappy about them, because it uses the names in sysfs
attributes:
power_supply olpc-ac: hwmon: 'olpc-ac' is not a valid name attribute, please fix
power_supply olpc-battery: hwmon: 'olpc-battery' is not a valid name attribute, please fix
See also commit 648cd48c9e ("hwmon: Do not accept invalid name
attributes") and commit 74d3b64197 ("hwmon: Relax name attribute
validation for new APIs").
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
This delay-fix is picked up from downstream driver,
we measured that 25 - 35 ms delay ensure that we get required data.
Tested on SMB347 on Nexus 7 2012. Otherwise IRQSTAT_E fails to provide
correct information.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: David Heidelberg <david@ixit.cz>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Fix failure when USB cable is connected:
smb347 2-006a: reading IRQSTAT_D failed
Fixes: 1502cfe19b ("smb347-charger: Fix battery status reporting logic for charger faults")
Tested-by: David Heidelberg <david@ixit.cz>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: David Heidelberg <david@ixit.cz>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The "default n" is not needed as it is, well, default. Clean
the KConfig by removing "default n".
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Indent the help text as explained in
Documentation/process/coding-style.rst
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The ROHM BD99954 is a Battery Management LSI for 1-4 cell Lithium-Ion
secondary battery intended to be used in space-constraint equipment such
as Low profile Notebook PC, Tablets and other applications. BD99954
provides a Dual-source Battery Charger, two port BC1.2 detection and a
Battery Monitor.
Support ROHM BD99954 Charger IC.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Change the bd70528 to use common linear_range code instead of
implementing a copy of it in this driver.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Series extracts a "linear ranges" helper out of the regulator
framework. Linear ranges helper is intended to help converting
real-world values to register values when conversion is linear. I
suspect this is useful also for power subsystem and possibly for clk.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAl61lKwTHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0HxeB/9dblIbC+28MvcEHXCcYBZBouOnrM8E
bIOMXkgEj1uL78ozOm7tMCgEpaKgv6BHdDuClCBvjbr0uOtAi0qUiv0IBotuVrdo
lq73l8l7OPz6TFFKIt8WsgwKnzdkuQC08+qrZasAdluRQnqnmkU2tvl2y9zaaaR4
6hGw+Nwx/pgeCXCa3pu+rCYwA7g0Tf8a6DDC6LyQWZameBJ1ey/YDjhJEeSmY7P7
306zs8YVxHhQMLUQ5T7DA6r/KWMNkO1SOueCqTjxWZc/XamGEcbsZG1cWrAnkoE2
VKLXBtYC75coNxIiu8ZxnQwLLdz1EQPdtg0qmzSjXJ68QjbWWzf4K1ra
=LG9G
-----END PGP SIGNATURE-----
Merge tag 'tags/linear-ranges-lib' into psy-next
lib: Add linear ranges helper library and start using it
Series extracts a "linear ranges" helper out of the regulator
framework. Linear ranges helper is intended to help converting
real-world values to register values when conversion is linear. I
suspect this is useful also for power subsystem and possibly for clk.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
In the probe function, in case of error, resources allocated in
'lp8788_setup_adc_channel()' must be released.
This can be achieved easily by using the devm_ variant of
'iio_channel_get()'.
This has the extra benefit to simplify the remove function and to axe the
'lp8788_release_adc_channel()' function which is now useless.
Fixes: 98a2766493 ("power_supply: Add new lp8788 charger driver")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Fix the following warning:
drivers/power/supply/cw2015_battery.c:96:5: warning:
'cw_update_profile' was not declared. Should it be static?
drivers/power/supply/cw2015_battery.c:712:1: warning:
'cw_bat_pm_ops' was not declared. Should it be static?
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: ChenTao <chentao107@huawei.com>
Acked-by: Tobias Schramm <t.schramm@manjaro.org>
Tested-by: Tobias Schramm <t.schramm@manjaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
We introduced some new locking here, but need to update the error
paths so they unlock before returning.
Fixes: 72d9cd9cdc ("power: bq25890: protect view of the chip's state")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Add POWER_SUPPLY_TYPE to the uevent env for power supply. Type is a
property of all power supplies and there is a sysfs entry for it but it
is not included in the properties array of the power supply so
explicitly add it to the udev env.
Signed-off-by: Mathew King <mathewk@chromium.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Reduce the number of touch points to add a new enum property to the
power_supply class by mapping the array of text values to the device
attribute descriptor. A new enum property can now added by creating an
array with the text values named POWER_SUPPLY_${PROPNAME}_TEXT and
adding POWER_SUPPLY_ENUM_ATTR(${PROPNAME}) to the power_supply_attrs
array.
Signed-off-by: Mathew King <mathewk@chromium.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Use designated initializers for the sysfs power supply text values. This
will help ensure that the text values are kept in sync with the enum
values from power_supply.h.
Signed-off-by: Mathew King <mathewk@chromium.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Make the device attribute list used to create sysfs attributes more
robust by decoupling the list order from order of the enum defined in
power_supply.h. This is done by using a designated initializer in the
POWER_SUPPLY_ATTR macro.
Signed-off-by: Mathew King <mathewk@chromium.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Extend bq->lock over whole updating of the chip's state. Might get
useful later for switching ADC modes correctly.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
regmap initialization will check I2C adapter functionality.
Remove redundant check in the driver.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Property list should not change, so mark it const.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Driver rejects unknown chips early in the probe(), so when
bq25890_power_supply_get_property() is made reachable, bq->chip_version
will already be set to correct value - there is no need to check
it again.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
This patch adds a driver for the CellWise cw2015 fuel gauge.
The CellWise cw2015 is a shuntless, single-cell Li-Ion fuel gauge used
in the pine64 Pinebook Pro laptop and some Raspberry Pi UPS HATs.
Signed-off-by: Tobias Schramm <t.schramm@manjaro.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
