Current poll transfer will read/write one word, then wait till the
hw is non-busy, it's not efficient. This patch will try to read/write
as many words as permitted by hardware FIFO depth.
Signed-off-by: Alek Du <alek.du@intel.com>
Signed-off-by: Feng Tang <feng.tang@intel.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The flush() is used to drain all the left data in rx fifo, currently
is is always called together with disabling hw. But from spec, disabling
hw will also reset all the fifo, so flush() is not needed.
Signed-off-by: Alek Du <alek.du@intel.com>
Signed-off-by: Feng Tang <feng.tang@intel.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The original version has many duplicated codes for null/u8/u16 case,
so unify them to make it cleaner
Signed-off-by: Feng Tang <feng.tang@intel.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
* 'devicetree/merge' of git://git.secretlab.ca/git/linux-2.6:
spi/pl022: Add loopback support for the SPI on 5500
spi/omap_mcspi: Fix broken last word xfer
of/flattree: minor cleanups
dt: eliminate OF_NO_DEEP_PROBE and test for NULL match table
dt: protect against NULL matches passed to of_match_node()
dt: Refactor of_platform_bus_probe()
Extend the vendor data with a loopback field, and add new
amba-pl022 vendor data for the DB5500 pl023, as the pl023
on db8500 and db5500 vary.
Signed-off-by: Prajadevi H <prajadevi.h@stericsson.com>
Signed-off-by: Philippe Langlais <philippe.langlais@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Commit adef658 "spi/omap_mcspi: catch xfers of non-multiple SPI word size"
broke the transmission of last word in cases where access is multiple of
word size and word size is 16 or 32 bits.
Fix this by replacing the test "c > (word_len>>3)" in do-while loops with
"c >= 'pointer increment size'". This ensures that the last word is
transmitted in above case and still allow to break the loop and prevent
variable c underflow in cases where word size != 'pointer increment size'.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Tested-by: Sourav Poddar<sourav.poddar@ti.com>
Acked-by: Michael Jones <michael.jones@matrix-vision.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The cell's platform_data is now accessed with a helper function;
change clients to use that, and remove the now-unused data_size.
Note that the mfd's platform_data is marked __devinitdata. This
is still correct in all cases except for the timbgpio driver, whose
remove hook has been changed to no longer reference the pdata.
Signed-off-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
* 'spi/next' of git://git.secretlab.ca/git/linux-2.6: (34 commits)
spi/dw_spi: move dw_spi.h into drivers/spi
spi/dw_spi: Fix missing header
gpio/langwell: Clear edge bit before handling
gpio/langwell: Simplify demux loop
gpio/langwell: Convert irq name space
gpio/langwell: Fix broken irq_eoi change.
gpio; Make Intel chipset gpio drivers depend on x86
gpio/cs5535-gpio: Fix section mismatch
spi/rtc-{ds1390,ds3234,m41t94}: Use spi_get_drvdata() for SPI devices
spi/davinci: Support DMA transfers larger than 65535 words
spi/davinci: Use correct length parameter to dma_map_single calls
gpio: Use __devexit at necessary places
gpio: add MODULE_DEVICE_TABLE to pch_gpio and ml_ioh_gpio
gpio/mcp23s08: support mcp23s17 variant
of_mmc_spi: add card detect irq support
spi/omap_mcspi: catch xfers of non-multiple SPI word size
spi/omap_mcspi: Off-by-one error in finding the right divisor
gpio/pca953x: Fix wrong pointer type
spi/pl022: rid dangling labels
spi: add support for SuperH SPI
...
include/linux/dw_spi.h only includes driver internal data. It doesn't
expose a platform_data configuration structure or similar (at least
nothing in-tree). This patch moves the header into drivers/spi so
that the scope is limited to only the dw_spi_*.c driver files
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Cc: Feng Tang <feng.tang@intel.com>
Cc: spi-devel-general@lists.sourceforge.net
* 'omap-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6: (258 commits)
omap: zoom: host should not pull up wl1271's irq line
arm: plat-omap: iommu: fix request_mem_region() error path
OMAP2+: Common CPU DIE ID reading code reads wrong registers for OMAP4430
omap4: mux: Remove duplicate mux modes
omap: iovmm: don't check 'da' to set IOVMF_DA_FIXED flag
omap: iovmm: disallow mapping NULL address when IOVMF_DA_ANON is set
omap2+: mux: Fix compile when CONFIG_OMAP_MUX is not selected
omap4: board-omap4panda: Initialise the serial pads
omap3: board-3430sdp: Initialise the serial pads
omap4: board-4430sdp: Initialise the serial pads
omap2+: mux: Add macro for configuring static with omap_hwmod_mux_init
omap2+: mux: Remove the use of IDLE flag
omap2+: Add separate list for dynamic pads to mux
perf: add OMAP support for the new power events
OMAP4: Add IVA OPP enteries.
OMAP4: Update Voltage Rail Values for MPU, IVA and CORE
OMAP4: Enable 800 MHz and 1 GHz MPU-OPP
OMAP3+: OPP: Replace voltage values with Macros
OMAP3: wdtimer: Fix CORE idle transition
Watchdog: omap_wdt: add fine grain runtime-pm
...
Fix up various conflicts in
- arch/arm/mach-omap2/board-omap3evm.c
- arch/arm/mach-omap2/clock3xxx_data.c
- arch/arm/mach-omap2/usb-musb.c
- arch/arm/plat-omap/include/plat/usb.h
- drivers/usb/musb/musb_core.h
* 'devel-stable' of master.kernel.org:/home/rmk/linux-2.6-arm: (289 commits)
davinci: DM644x EVM: register MUSB device earlier
davinci: add spi devices on tnetv107x evm
davinci: add ssp config for tnetv107x evm board
davinci: add tnetv107x ssp platform device
spi: add ti-ssp spi master driver
mfd: add driver for sequencer serial port
ARM: EXYNOS4: Implement Clock gating for System MMU
ARM: EXYNOS4: Enhancement of System MMU driver
ARM: EXYNOS4: Add support for gpio interrupts
ARM: S5P: Add function to register gpio interrupt bank data
ARM: S5P: Cleanup S5P gpio interrupt code
ARM: EXYNOS4: Add missing GPYx banks
ARM: S3C64XX: Fix section mismatch from cpufreq init
ARM: EXYNOS4: Add keypad device to the SMDKV310
ARM: EXYNOS4: Update clocks for keypad
ARM: EXYNOS4: Update keypad base address
ARM: EXYNOS4: Add keypad device helpers
ARM: EXYNOS4: Add support for SATA on ARMLEX4210
plat-nomadik: make GPIO interrupts work with cpuidle ApSleep
mach-u300: define a dummy filter function for coh901318
...
Fix up various conflicts in
- arch/arm/mach-exynos4/cpufreq.c
- arch/arm/mach-mxs/gpio.c
- drivers/net/Kconfig
- drivers/tty/serial/Kconfig
- drivers/tty/serial/Makefile
- drivers/usb/gadget/fsl_mxc_udc.c
- drivers/video/Kconfig
* 'defcfg' of master.kernel.org:/home/rmk/linux-2.6-arm:
ARM: 6647/1: add Versatile Express defconfig
ARM: 6644/1: mach-ux500: update the U8500 defconfig
* 'drivers' of master.kernel.org:/home/rmk/linux-2.6-arm:
ARM: 6764/1: pl011: factor out FIFO to TTY code
ARM: 6763/1: pl011: add optional RX DMA to PL011 v2
ARM: 6758/1: amba: support pm ops
ARM: amba: make amba_driver id_table const
ARM: amba: make internal ID table handling const
ARM: amba: make probe() functions take const id tables
ARM: 6662/1: amba: make amba_bustype non-static
ARM: mmci: add dmaengine-based DMA support
ARM: mmci: no need for separate host->data_xfered
ARM: mmci: avoid unnecessary switch to data available PIO interrupts
ARM: mmci: no need to call flush_dcache_page() with sg_miter API
ARM: mmci: avoid reporting too many completed bytes on fifo overrun
ALSA: AACI: make fifo variables more explanitory
ALSA: AACI: no need to call snd_pcm_period_elapsed() for each period
ALSA: AACI: use snd_pcm_lib_period_bytes()
ALSA: AACI: clean up AACI announcement printk
ALSA: AACI: fix channel mask selection
ALSA: AACI: fix number of channels for record
ALSA: AACI: fix multiple IRQ claiming
* 'cyberpro-next' of master.kernel.org:/home/rmk/linux-2.6-arm:
VIDEO: cyberpro: remove unused cyber2000fb_get_fb_var()
VIDEO: cyberpro: remove useless function extreg pointers
VIDEO: cyberpro: update handling of device structures
VIDEO: cyberpro: add support for video capture I2C
VIDEO: cyberpro: make 'reg_b0_lock' always present
VIDEO: cyberpro: add I2C support
VIDEO: cyberpro: select lowest multipler/divisor for PLL
This patch adds an SPI master implementation that operates on top of an
underlying TI-SSP port.
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Cyril Chemparathy <cyril@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
The current davinci SPI driver, in DMA mode, is limited to 65535
words for a single transfer. Modify the driver by configuring a
3 dimensional EDMA transfer to support up to 65535x65535
words.
Signed-off-by: Michael Williamson <michael.williamson@criticallink.com>
Tested-by: Stefano Babic <sbabic@denx.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The davinci spi driver provides an option to use DMA transfers for
data. In the dma_map_single() call, the driver is passing the
number of words to be transfered for the mapping size. It should
be the number of bytes.
Signed-off-by: Michael Williamson <michael.williamson@criticallink.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Move to SOC_SOC_IMX3X.
Leave ARCH_MX31/35 definitions there, in case some place prevent multi-soc
single image.
Signed-off-by: Richard Zhao <richard.zhao@freescale.com>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Move to SOC_SOC_IMX5X. Leave only places which prevent multi-soc
using ARCH_MX5X.
Signed-off-by: Richard Zhao <richard.zhao@freescale.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
If an SPI access was not a multiple of the SPI word size,
the while() loop would spin and the rx/tx ptrs would be incremented
indefinitely.
Signed-off-by: Michael Jones <michael.jones@matrix-vision.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
For DMA operation, the davinci spi driver needs an event queue number.
Currently, this number is passed as a IORESOURCE_DMA. This is not
correct, as the event queue is not a DMA channel. Pass the event queue
via the platform data structure instead.
On dm355 and dm365, move the eventq assignment for spi0 out of resources
array and into platform data.
Signed-off-by: Michael Williamson <michael.williamson@criticallink.com>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Get rid of users of of_platform_driver in drivers/spi. The
of_platform_{,un}register_driver functions are going away, so the
users need to be converted to using the platform_bus_type directly.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Off-by-one error, gave erroneous divisor value 16 if speed_hz is over zero but
less than OMAP2_MCSPI_MAX_FREQ / (1 << 15), that is, [1..1463].
Also few overly complex bit shifts in divisor fixed.
Also one dev_dgb line fixed, which indicated max speed exceeding transfer speed.
Introducing a new function omap2_mcspi_calc_divisor() for getting the right
divisor in omap2_mcspi_setup_transfer().
Signed-off-by: Phil Carmody <ext-phil.2.carmody@nokia.com>
Signed-off-by: Hannu Heikkinen <ext-hannu.m.heikkinen@nokia.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Make Primecell driver probe functions take a const pointer to their
ID tables. Drivers should never modify their ID tables in their
probe handler.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Remove a compilation error regarding unused labels that came about
when simplifying the DMA code.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The SH7757 has SPI0 module. This patch supports it.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
[grant.likely@secretlab.ca: fixed Makefile ordering, added
__dev{init,exit} annotations, removed DRIVER_VERSION (this is
mainline, the version == the kernel version) and tidied some
indentation & style stuff]
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This patch adds a new SPI driver to support the Altera SOPC Builder
SPI component. It uses the bitbanging library.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This patch adds support of OpenCores tiny SPI driver.
http://opencores.org/project,tiny_spi
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
McSPI runtime conversion.
Changes involves:
1) remove clock framework apis to use runtime framework apis.
2) context restore from runtime resume which is a callback for get_sync.
3) Remove SYSCONFIG(sysc) register handling
(a) Remove context save and restore of sysc reg and remove soft reset
done from sysc reg as this will be done with hwmod framework.
(b) Also cleanup sysc reg bit macros.
4) Rename the omap2_mcspi_reset function to omap2_mcspi_master_setup
function as with hwmod changes soft reset will be done in
hwmod framework itself and use the return value from clock
enable function to return for failure scenarios.
Signed-off-by: Charulatha V <charu@ti.com>
Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Reviewed-by: Partha Basak <p-basak2@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Cleans up all base address definitions for omap_mcspi
and adapts the device registration and driver to hwmod framework.
Changes involves:
1) Removing all base address macro defines.
2) Using omap-device layer to register device and utilizing data from
hwmod data file for base address, dma channel number, Irq_number,
device attribute(number of chipselect).
3) Appending base address with pdata reg_offset for omap4 boards.
For omap4 all regs used in driver deviate with reg_offset_macros
defined with an value of 0x100. So pass this offset through pdata
and append the same to base address retrieved from hwmod data file
and we are not mapping *_HL_* regs which are not used in driver.
Signed-off-by: Charulatha V <charu@ti.com>
Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Reviewed-by: Partha Basak <p-basak2@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The hardware seems to have a race condition when the inactive
channels are in slave mode. We support master mode only, so
we can just switch all channels to master mode.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
[ukleinek: add more verbose comment about the race]
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This utilizes the new core voltage switch to power off the PL022
core voltage when it's not in use transmitting packets, if and
only if a core voltage switch is available.
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This simplifies the DMA code a bit by using the dmaengine helpers.
The cookie from descriptor submission can be ignored in this case
as has been established in review of the MMCI/PL180 driver.
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
setup_transfer is mandatory if spi_bitbang_transfer is used, so
check for it during initialization and not each time during runtime.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
If there is an error with setting up a transfer, we need to return
immediately rather than trying to continue to process things. We
already set up the error states for the caller at this point.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
We can do multiples of 8bit transfers when using the hardware CS and a
little bit of magic, so make it work.
Signed-off-by: Bob Liu <lliubbo@gmail.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Right now the platform device and its platform data is included in one big
struct which requires its custom ->release function. The problem with the
release function within the driver is that it might be called after the
driver was removed because someone was holding a reference to it and it
was not called right after platform_device_unregister(). So we also free
the platform device memory to which one might hold a reference.
This patch uses the normal pdev functions so this kind of race does not
occur.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Add the compat_ioctl for operations on /dev/spi* so that 32 bit
userspace applications can access SPI. As far as I can see all data
structure are already prepared for that, so no additional conversion has
to be done.
My use case is MIPS with N32 userspace ABI and toolchain, and that was
also the platform where I tested it successfully (Cavium Octeon).
Signed-off-by: Bernhard Walle <walle@corscience.de>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
We want to have just CONFIG_ARCH_OMAP2, 3 and 4. The rest
are nowadays just subcategories of these.
Search and replace the following:
ARCH_OMAP2420 SOC_OMAP2420
ARCH_OMAP2430 SOC_OMAP2430
ARCH_OMAP3430 SOC_OMAP3430
No functional changes.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Thomas Weber <weber@corscience.de>
Acked-by: Sourav Poddar <sourav.poddar@ti.com>
Instead of sending data 8 bits at a time in 8-bit SPI mode, swap bytes
and send and receive them 32 bits at a time. Tested with an SD-card,
with which this patch reduced the number of interrupts by 50%, when
reading 5MiB of data (there are also small service packets, the number
of interrupts, produced by 512-byte sectors should, of course, drop by
75%), and improved throughput by more than 40%.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
NULL + <small offset> != NULL, but reading from that <small offset> address
is usually not a very good idea and often leads to problems, like kernel
Oopses in this case, easily reproducible by writing to an SD-card, used in
SPI mode.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Having conditional around the of_match_table and the of_node pointers
turns out to make driver code use ugly #ifdef blocks. Drop the
conditionals and remove the #ifdef blocks from the affected drivers.
Also tidy up minor whitespace issues within the same hunks.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
* 'upstream' of git://git.linux-mips.org/pub/scm/upstream-linus: (26 commits)
MIPS: Malta: enable Cirrus FB console
MIPS: add CONFIG_VIRTUALIZATION for virtio support
MIPS: Implement __read_mostly
MIPS: ath79: add common WMAC device for AR913X based boards
MIPS: ath79: Add initial support for the Atheros AP81 reference board
MIPS: ath79: add common SPI controller device
SPI: Add SPI controller driver for the Atheros AR71XX/AR724X/AR913X SoCs
MIPS: ath79: add common GPIO buttons device
MIPS: ath79: add common watchdog device
MIPS: ath79: add common GPIO LEDs device
MIPS: ath79: add initial support for the Atheros PB44 reference board
MIPS: ath79: utilize the MIPS multi-machine support
MIPS: ath79: add GPIOLIB support
MIPS: Add initial support for the Atheros AR71XX/AR724X/AR931X SoCs
MIPS: jump label: Add MIPS support.
MIPS: Use WARN() in uasm for better diagnostics.
MIPS: Optimize TLB handlers for Octeon CPUs
MIPS: Add LDX and LWX instructions to uasm.
MIPS: Use BBIT instructions in TLB handlers
MIPS: Declare uasm bbit0 and bbit1 functions.
...
The Atheros AR71XX/AR724X/AR913X SoCs have a built-in SPI controller. This
patch implements a driver for that.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: spi-devel-general@lists.sourceforge.net
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Cc: linux-mips@linux-mips.org
Cc: Imre Kaloz <kaloz@openwrt.org>
Cc: Luis R. Rodriguez <lrodriguez@atheros.com>
Cc: Cliff Holden <Cliff.Holden@Atheros.com>
Cc: Kathy Giori <Kathy.Giori@Atheros.com>
Patchwork: https://patchwork.linux-mips.org/patch/1960/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Without this fix reloading of the driver is impossible.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
clk_freq is used uninitialized in pl022_setup routine. This patch
fix compilation warning for using uninitialized variable
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This patch enables the existing S3C64XX series SPI driver for S5P64X0
and removed dependency on EXPERIMENTAL because we don't need it now.
v3: Changed dependency of S3C64XX_DMA
v2: Removed dependency on EXPERIMENTAL
Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com>
Signed-off-by: Sangbeom Kim <sbkim73@samsung.com>
Acked-by: Jassi Brar <jassi.brar@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
clk_get() returns a struct clk cookie to the driver and some platforms
may return NULL if they only support a single clock. clk_get() has only
failed if it returns a ERR_PTR() encoded pointer.
Signed-off-by: Jamie Iles <jamie@jamieiles.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Some platforms have been known to return NULL from clk_get() if they
support only a single struct clk. Whilst tegra doesn't do this, make
the drivers consistent with others.
Signed-off-by: Jamie Iles <jamie@jamieiles.com>
Acked-by: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/suspend-2.6:
spi / PM: Support dev_pm_ops
PM: Prototype the pm_generic_ operations
PM / Runtime: Generic resume shouldn't set RPM_ACTIVE unconditionally
PM: Use dev_name() in core device suspend and resume routines
PM: Permit registration of parentless devices during system suspend
PM: Replace the device power.status field with a bit field
PM: Remove redundant checks from core device resume routines
PM: Use a different list of devices for each stage of device suspend
PM: Avoid compiler warning in pm_noirq_op()
PM: Use pm_wakeup_pending() in __device_suspend()
PM / Wakeup: Replace pm_check_wakeup_events() with pm_wakeup_pending()
PM: Prevent dpm_prepare() from returning errors unnecessarily
PM: Fix references to basic-pm-debugging.txt in drivers-testing.txt
PM / Runtime: Add synchronous runtime interface for interrupt handlers (v3)
PM / Hibernate: When failed, in_suspend should be reset
PM / Hibernate: hibernation_ops->leave should be checked too
Freezer: Fix a race during freezing of TASK_STOPPED tasks
PM: Use proper ccflag flag in kernel/power/Makefile
PM / Runtime: Fix comments to match runtime callback code
* 'next-spi' of git://git.secretlab.ca/git/linux-2.6: (77 commits)
spi/omap: Fix DMA API usage in OMAP MCSPI driver
spi/imx: correct the test on platform_get_irq() return value
spi/topcliff: Typo fix threhold to threshold
spi/dw_spi Typo change diable to disable.
spi/fsl_espi: change the read behaviour of the SPIRF
spi/mpc52xx-psc-spi: move probe/remove to proper sections
spi/dw_spi: add DMA support
spi/dw_spi: change to EXPORT_SYMBOL_GPL for exported APIs
spi/dw_spi: Fix too short timeout in spi polling loop
spi/pl022: convert running variable
spi/pl022: convert busy flag to a bool
spi/pl022: pass the returned sglen to the DMA engine
spi/pl022: map the buffers on the DMA engine
spi/topcliff_pch: Fix data transfer issue
spi/imx: remove autodetection
spi/pxa2xx: pass of_node to spi device and set a parent device
spi/pxa2xx: Modify RX-Tresh instead of busy-loop for the remaining RX bytes.
spi/pxa2xx: Add chipselect support for Sodaville
spi/pxa2xx: Consider CE4100's FIFO depth
spi/pxa2xx: Add CE4100 support
...
Running the latest kernel on the 4430SDP board with DMA API debugging
enabled results in this:
WARNING: at lib/dma-debug.c:803 check_unmap+0x19c/0x6f0()
NULL NULL: DMA-API: device driver tries to free DMA memory it has not allocated
[device address=0x000000008129901a] [size=260 bytes]
Modules linked in:
Backtrace:
[<c003cbe0>] (dump_backtrace+0x0/0x10c) from [<c0278da8>] (dump_stack+0x18/0x1c)
r7:c1839dc0 r6:c0198578 r5:c0304b17 r4:00000323
[<c0278d90>] (dump_stack+0x0/0x1c) from [<c005b158>] (warn_slowpath_common+0x58/0x70)
[<c005b100>] (warn_slowpath_common+0x0/0x70) from [<c005b214>] (warn_slowpath_fmt+0x38/0x40)
r8:c1839e40 r7:00000000 r6:00000104 r5:00000000 r4:8129901a
[<c005b1dc>] (warn_slowpath_fmt+0x0/0x40) from [<c0198578>] (check_unmap+0x19c/0x6f0)
r3:c03110de r2:c0304e6b
[<c01983dc>] (check_unmap+0x0/0x6f0) from [<c0198cd8>] (debug_dma_unmap_page+0x74/0x80)
[<c0198c64>] (debug_dma_unmap_page+0x0/0x80) from [<c01d5ad8>] (omap2_mcspi_work+0x514/0xbf0)
[<c01d55c4>] (omap2_mcspi_work+0x0/0xbf0) from [<c006dfb0>] (process_one_work+0x294/0x400)
[<c006dd1c>] (process_one_work+0x0/0x400) from [<c006e50c>] (worker_thread+0x220/0x3f8)
[<c006e2ec>] (worker_thread+0x0/0x3f8) from [<c00738d0>] (kthread+0x88/0x90)
[<c0073848>] (kthread+0x0/0x90) from [<c005e924>] (do_exit+0x0/0x5fc)
r7:00000013 r6:c005e924 r5:c0073848 r4:c1829ee0
---[ end trace 1b75b31a2719ed20 ]---
I've no idea why this driver uses NULL for dma_unmap_single instead of
the &spi->dev that is laying around just waiting to be used in that
function - but it's an easy fix.
Also replace this comment with a FIXME comment:
/* Do DMA mapping "early" for better error reporting and
* dcache use. Note that if dma_unmap_single() ever starts
* to do real work on ARM, we'd need to clean up mappings
* for previous transfers on *ALL* exits of this loop...
*/
as the comment is not true - we do work in dma_unmap() functions,
particularly on ARMv6 and above. I've corrected the existing unmap
functions but if any others are required they must be added ASAP.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The test "if (spi_imx->irq <= 0)" is not testing the IRQ value, but
the return value of platform_get_irq(). As platform_get_irq() can
return an error (-ENXIO) or the IRQ value it found, the test should be
"if (spi_imx->irq < 0)"
[grant.likely: Note: In general, Linux irq number 0 should also mean
no irq, but arm still allows devices to be assigned 0, and the imx
platform uses 0 for one of the spi devices, so this patch is needed
for the device to work]
Signed-off-by: Richard Genoud <richard.genoud@gmail.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
After grabbing a msg from the msgq, the mcfqspi_work function calls
list_del_init on the mcfqspi->msgq which unintentionally deletes the rest
of the list before it can be processed. If qspi call was made using
spi_sync, this can result in a process hang.
Signed-off-by: Jate Sujjavanich <jsujjavanich@syntech-fuelmaster.com>
Acked-by: Steven King <sfking@fdwdc.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The user must read N bytes of SPIRF (1 <= N <= 4) that do not exceed the
amount of data in the receive FIFO, so read the SPIRF byte by byte when
the data in receive FIFO is less than 4 bytes.
On Simics, when read N bytes that exceed the amout of data in receive
FIFO, we can't read the data out, that is we can't clear the rx FIFO,
then the CPU will loop on the espi rx interrupt.
Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
When SPI wake up from OFF mode, CS is in the wrong state: force it to the
inactive state.
During the system life, I monitored the CS behavior using a oscilloscope.
I also activated debug in omap2_mcspi, so I saw when driver disable the clocks
and restore context when device is not used.Each time the CS was in the correct
state. It was only when system was put suspend to ram with off-mode activated
that on resume the CS was in wrong state( ie activated).
Changelog:
* Change from v1 to v2:
- Rebase on linus/master (after 2.6.37-rc1)
- Do some clean-up and fix indentation on both patches
- Add more explanations for patch 2
* Change from v2 to v3:
- Use directly resume function of spi_master instead of using function
- from spi_device as Grant Likely pointed it out.
- Force this transition explicitly for each CS used by a device.
* Change from v3 to v4:
- Patch clean-up according to Kevin Hilman and checkpatch.
- Now force CS to be in inactive state only if it was inactive when it was
suspended.
* Change from v4 to v5:
- Rebase on linus/master (after 2.6.37-rc3)
- Collapse some lines as pointed by Grant Likely
- Fix a spelling
* Change from v5 to v6:
- Rebase on linus/master (after 2.6.37-rc7)
- Use CONFIG_SUSPEND instead of CONFIG_PM
- Didn't use legacy PM methods anymore. Instead, add a struct dev_pm_ops and
add the resume method there.
- Fix multi-line comment style
* Change from v6 to v7:
- Rebase on linus/master (after 2.6.37-rc8)
- Drop an extra line
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Reviewed-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
* 'spi' of git://git.linutronix.de/users/bigeasy/soda into spi/next
spi/pxa2xx: register driver properly
spi/pxa2xx: add support for shared IRQ handler
spi/pxa2xx: Use define for SSSR_TFL_MASK instead of plain numbers
arm/pxa2xx: reorgazine SSP and SPI header files
spi/pxa2xx: Add CE4100 support
spi/pxa2xx: Consider CE4100's FIFO depth
spi/pxa2xx: Add chipselect support for Sodaville
spi/pxa2xx: Modify RX-Tresh instead of busy-loop for the remaining RX bytes.
spi/pxa2xx: pass of_node to spi device and set a parent device
* 'for-grant' of git://arago-project.org/git/projects/linux-davinci into spi/next
spi: davinci: fix checkpatch errors
spi: davinci: whitespace cleanup
spi: davinci: remove unused variable 'pdata'
spi: davinci: set chip-select mode in SPIDEF only once
spi: davinci: enable both activation and deactivation of chip-selects
spi: davinci: remove unnecessary data transmit on CS disable
spi: davinci: enable GPIO lines to be used as chip selects
spi: davinci: simplify prescalar calculation
spi: davinci: remove 'wait_enable' platform data member
spi: davinci: make chip-slect specific parameters really chip-select specific
spi: davinci: consolidate setup of SPIFMTn in one function
spi: davinci: setup chip-select timers values only if timer enabled
spi: davinci: add support for wait enable timeouts
spi: davinci: remove unused members of davinci_spi_slave
spi: davinci: eliminate the single member structure davinci_spi_slave
spi: davinci: eliminate unnecessary update of davinci_spi->count
spi: davinci: simplify calculation of edma acount value
spi: davinci: check for NULL buffer pointer before using it
spi: davinci: remove unnecessary disable of SPI
spi: davinci: remove unnecessary 'count' variable in driver private data
spi: davinci: remove unnecessary completion variable initialization
spi: davinci: remove non-useful interrupt mode support
spi: davinci: simplify poll mode transfers
spi: davinci: add support for interrupt mode
spi: davinci: configure the invariable bits in spipc0 only once
spi: davinci: remove unnecessary function davinci_spi_bufs_prep()
spi: davinci: remove unnecessary call to davinci_spi_setup_transfer()
spi: davinci: do not store DMA channel information per chip select
spi: davinci: always start transmit DMA
spi: davinci: do not use temporary buffer if no transmit data provided
spi: davinci: always start receive DMA
spi: davinci: use edma_write_slot() to setup EDMA PaRAM slot
spi: davinci: fix DMA event generation stoppage
spi: davinci: fix EDMA CC errors at end of transfers
spi: davinci: handle DMA completion errors correctly
spi: davinci: remove usage of additional completion variables for DMA
spi: davinci: let DMA operation be specified on per-device basis
spi: davinci: remove non-useful "clk_internal" platform data
spi: davinci: enable and power-up SPI only when required
spi: davinci: setup the driver owner
spi: davinci: add additional comments
spi: davinci: add EF Johnson Technologies copyright
spi: davinci: removed unused #defines
spi: davinci: remove unnecessary typecast
spi: davinci: do not treat Tx interrupt being set as error
spi: davinci: do not allocate DMA channels during SPI device setup
spi: davinci: remove unnecessary private data member 'region_size'
spi: davinci: shorten variable names
spi: davinci: kconfig: add manufacturer name to prompt string
Allow SPI drivers to use runtime PM and other dev_pm_ops features by
implementing dev_pm_ops for the bus. The existing bus specific suspend
and resume functions will be called if a driver does not provide dev_pm_ops
allowing for transition to the new model.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
* 'merge' of git://git.secretlab.ca/git/linux-2.6:
spi/mpc52xx-spi: fix annotation for remove()-pointer
spi/fsl_espi: fix wrong setting of the address in the command buffer
spi/fsl_espi: change the read behaviour of the SPIRF
of/i2c: Fix request module by alias
powerpc/mpc5200: include fs.h in mpc52xx_gpt.c
Probe/remove should be in __devinit/__devexit. Found by a section-mismatch
warning. Also, copy do_remove() over to remove().
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Or else we can't operate on the right address when the trans length
is greater than 65535.
Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The user must read N bytes of SPIRF (1 <= N <= 4) that do not exceed the
amount of data in the receive FIFO, so read the SPIRF byte by byte when
the data in receive FIFO is less than 4 bytes.
On Simics, when read N bytes that exceed the amount of data in receive
FIFO, we can't read the data out, that is we can't clear the rx FIFO,
then the CPU will loop on the espi rx interrupt.
Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
dw_spi driver in upstream only supports PIO mode, and this patch
will support it to cowork with the Designware dma controller used
on Intel Moorestown platform, at the same time it provides a general
framework to support dw_spi core to cowork with dma controllers on
other platforms
It has been tested with a Option GTM501L 3G modem and Infenion 60x60
modem. To use DMA mode, DMA controller 2 of Moorestown has to be enabled
Also change the dma interface suggested by Linus Walleij.
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Feng Tang <feng.tang@intel.com>
[Typo fix and renames to match intel_mid_dma renaming]
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The SPI polling loop timeout only works with HZ=100 as the loop was
actually too short.
Also add appropriate cpu_relax() in the busy wait loops...
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Feng Tang <feng.tang@intel.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This variable is a bool but defined an int and defined completely
backwards. This makes the code more readable.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The sglen return by the dma_map_sg() should be passed to the DMA
engine, not the one passed in. If we one day have a DMA mapper
that can coalesce entries, this will bug due to a too large
number of entries being passed in.
Reported-by: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The struct device for the DMA engine is the apropriate one to use
when mapping/unmapping buffers. This is because the memory which
is addressable by DMA is determined by the DMA engine rather than
the device.
Reported-by: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
It seems spi_topcliff_pch of linux-2.6.37-rc6 degraded by previous patch.
In fact, data transfer fails on evaluation board testing.
I found like the following register miss-setting line.
Using this patch, I have confirmed data transfer can work well.
Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
There are no machines in-tree that still use the driver
name as device name. So save a few bytes and remove it.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Jason Wang <jason77.wang@gmail.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This was fixed by David Lamparter in v2.6.36-rc5 3486008 ("spi: free
children in spi_unregister_master, not siblings") and broken again in
v2.6.37-rc1~2^2~4 during the merge of 2b9603a0 ("spi: enable
spi_board_info to be registered after spi_master").
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: David Lamparter <equinox@diac24.net>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Conflicts:
MAINTAINERS
arch/arm/mach-omap2/pm24xx.c
drivers/scsi/bfa/bfa_fcpim.c
Needed to update to apply fixes for which the old branch was too
outdated.
There is a possibility that the last word of a transaction will be lost
if data is not ready. Re-read in poll_transfer() to solve this issue
when poll_mode is enabled.
Verified on SPI touch screen device.
Signed-off-by: Major Lee <major_lee@wistron.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
After all TX bytes are sent, the driver spins while the SPI core is busy
and then it spins for a "short" period of time until RX bytes are
available.
On Sodavile the busy flag disappears pretty quick and after that it
takes approx ~130ms (sometimes less but not much) until there are bytes
available in the RX FIFO.
This patch removes the busy loop and modifies the RX threshould so we
get woken up once the remainings bytes arrived.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Dirk Brandewie <dirk.brandewie@gmail.com>
The SPI core on Sodaville supports chip selects. Its configuration
moved into the SSSR register at bit 0 and 1. Thus Sodaville can be hooked
up with up to 4 devices.
This patch ensures that the bits which are otherwiese reserved are only
touched on Sodaville and not on any other PXAs. Also it makes sure that
the status register does not lose the CS information while clearing the
ROR bit.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Dirk Brandewie <dirk.brandewie@gmail.com>
For PXA the default threshold is FIFO_DEPTH / 2. Adjust this value for
CE4100.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Dirk Brandewie <dirk.brandewie@gmail.com>
Sodaville's SPI controller is very much the same as in PXA25x. The
difference:
- The RX/TX FIFO is only 4 words deep instead of 16
- No DMA support
- The SPI controller offers a CS functionality
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Dirk Brandewie <dirk.brandewie@gmail.com>
The PXA-SPI driver relies on some files / defines which are arm specific
and are within the ARM tree. The CE4100 SoC which is x86 has also the
SPI core.
This patch moves the ssp and spi files from arm/mach-pxa and plat-pxa to
include/linux where the CE4100 can access them.
This move got verified by building the following defconfigs:
cm_x2xx_defconfig corgi_defconfig em_x270_defconfig ezx_defconfig
imote2_defconfig pxa3xx_defconfig spitz_defconfig zeus_defconfig
raumfeld_defconfig magician_defconfig
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Dirk Brandewie <dirk.brandewie@gmail.com>
This is required in case the interrupt line is shared with other
devices.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Dirk Brandewie <dirk.brandewie@gmail.com>
passing argument 2 of 'dma_map_single' discards qualifiers from pointer target type
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
use platform_driver_register instead of platform_driver_probe. The
latter only checks available devices at the time of calling. So if a
device gets inserter at a later point in time then the driver will never
play with it.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Dirk Brandewie <dirk.brandewie@gmail.com>
Add manufacturer name to the Kconfig prompt string and move
the controller name to the begining of the prompt.
This helps locate the driver easily among the list of existing
drivers.
While at it, also add information about being able to build
the driver as module.
Tested-By: Brian Niebuhr <bniebuhr@efjohnson.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Shorten names of local variables and structure members where
possible.
Local variables:
* 'davinci_spi' is being renamed 'dspi'
* 'davinci_spi_dma' is being renamed 'dma'
Structure members:
* 'dma_{tx|rx}_channel' is being renamed '{tx|rx}_channel'
since the structure containing them is already called
'davinci_spi_dma'
* 'davinci_spi_dma' in 'davinci_spi' structure is being
renamed 'dma'
Tested-By: Brian Niebuhr <bniebuhr@efjohnson.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Remove unnecesary private data member 'region_size'
being used to store the size of SPI memory region.
Instead, get the memory resource size directly from
the platform data.
Tested-By: Brian Niebuhr <bniebuhr@efjohnson.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Add copyright for EF Johnson Technologies since the driver
has been majorly overhauled by Brian.
Signed-off-by: Brian Niebuhr <bniebuhr@efjohnson.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Add comments describing the platform data members
and per-chip-select SPI configuration structure.
Also, add some comments describing the what happens
during the driver probe.
Signed-off-by: Brian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: Michael Williamson <michael.williamson@criticallink.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Setup the owner member of the platform driver to THIS_MODULE
instead of leaving it NULL.
Signed-off-by: Brian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: Michael Williamson <michael.williamson@criticallink.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Enable SPI only when active transfers are in progress. Keep
it in local low power when not in use.
Signed-off-by: Brian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: Michael Williamson <michael.williamson@criticallink.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
The "clk_internal" platform data member which contols the
CLKMOD bit in Global Control Register 1 is not useful
since CLKMOD needs be set to 1 *always* to ensure master
mode operation.
Remove this platform data.
Signed-off-by: Brian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: Michael Williamson <michael.williamson@criticallink.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Let DMA operation be specified on a per-device basis instead
of selecting it once during probe.
A side effect of this is the need to combine the PIO and DMA buffer
txrx_bufs routine. This is good since they anyway share some common
functionality.
Signed-off-by: Brian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: Michael Williamson <michael.williamson@criticallink.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
The DMA code does not use the existing completion variable 'done'
which is being used for interrupt mode transfers. Instead it uses
two different completion variables specific to DMA mode transfers.
Eliminate the usage of new completion variables for DMA mode and
use the existing completion variable.
[nsekhar@ti.com: To make this process easy, eliminate the two
different DMA completion callback functions for tx and rx and
use a single callback function instead]
Signed-off-by: Brian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: Michael Williamson <michael.williamson@criticallink.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Do not simply clean the DMA channel on a DMA completion
error. Instead, use wcount and rcount members of davinci_spi
to detecion non-completion of DMA and signal EIO to the
application.
Signed-off-by: Brian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: Michael Williamson <michael.williamson@criticallink.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Use a dummy param slot linked to itself to take care of the
extra "sync event" that gets sent to EDMA controller after
the last byte has been transferred.
The dummy PaRAM slot that is linked to the actual DMA PaRAM
slot "absorbs" this event and prevents a EDMA CC error to
be asserted.
Without this provision, the EDMA CC error would be asserted
because the channel PaRAM would be empty after the transfer
and EDMA would not know what to make out of the extra sync
event.
Signed-off-by: Brian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: Michael Williamson <michael.williamson@criticallink.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Do not allocate (and de-allocate) SPI DMA channels during setup
(and cleanup) for each SPI device. Instead, allocate the DMA
channels once duing probe and use them for the life time of
the driver.
This makes sense since there are dedicated DMA channels meant
for SPI use.
This also helps remove the unnecessary DMA "sync_dev" variables
being used to store DMA channel information.
Also, the "use_dma" platform variable is now eliminated since
it is possible to check if the platform supports DMA or not
based upon whether DMA resources can be found or not.
Tested-By: Michael Williamson <michael.williamson@criticallink.com>
Tested-By: Brian Niebuhr <bniebuhr@efjohnson.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Do not stop SPI DMA event generation in either transmit or
receive DMA event call back because the single setting affects
both transmit and receive event generation.
Depending on the order in which the callbacks happen, transmit
or receive events can get unintentionally stalled.
Instead, disable event generation once after both the transmit
and receive DMA completes.
While at it, remove the largely under-used function to set or
clear DMA event generation.
Signed-off-by: Brian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: Michael Williamson <michael.williamson@criticallink.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Currently a series of EDMA API calls are being made to setup
various aspects of EDMA PaRAM slots for receive and transmit.
Instead setup the PaRAM using a local structure and write once
to the hardware using edma_write_slot()
Signed-off-by: Brian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: Michael Williamson <michael.williamson@criticallink.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
In keeping with the full duplex nature of the SPI bus. Always
start receive DMA along with transmit DMA.
If there is no receive buffer provided with the transfer, use
a temporary buffer to receive the data to be thrown away.
[michael.williamson@criticallink.com: receive DMA size should
be same as transfer length to avoid hang-up when transfer length
is smaller than temporary rx buffer size (rx buffer not provided)]
Signed-off-by: Brian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: Michael Williamson <michael.williamson@criticallink.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Remove usage of temporary buffer when no transmit data is provided.
Instead, use the transmit register itself as the source of data.
By choosing the transmit register itself as the source of data, this
patch helps remove unnecessary accesses to memory when no real data
is being transmitted.
Signed-off-by: Brian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: Michael Williamson <michael.williamson@criticallink.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Due to the full duplex nature of the SPI bus, the SPI master
on DaVinci needs transmit to be active even if the tranfer is
only meant to collect receive data.
The current code achieves this by using a temporary zeroed buffer
to provide DMA data in case the transfer does not have a transmit
buffer provided.
However, the transmit DMA is started only if transmit buffer is
provided rendering the temporary buffer unused. Instead the code
relies on a write to SPIDAT1 register to trigger transmit operation.
This however only sends two bytes of data.
Fix this by starting transmit DMA always.
This changes exposes a bug on DM355 where the CSHOLD bit in
SPIDAT1 needs to be written to in between transfers. Handle
that by introducing a "cshold_bug" platform data which is
set to true for DM355.
Signed-off-by: Brian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: Michael Williamson <michael.williamson@criticallink.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Do not store DMA channel related information per chip-select since
that information does not depend on the chip select.
The same DMA channels can be used for transfers on all chip-selects
since the transfer happens one-at-a-time.
Signed-off-by: Brian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: Michael Williamson <michael.williamson@criticallink.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Remove unnecessary call to davinci_spi_setup_transfer() at the end
of davinci_spi_setup().
davinci_spi_setup_transfer() is registered as the setup_transfer
callback for the bitbang layer and is called independently by
the bitbang layer to setup the transfer before it begins.
Signed-off-by: Brian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: Michael Williamson <michael.williamson@criticallink.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
The function davinci_spi_bufs_prep() is doing stuff that
davinci_spi_setup() is doing. Eliminate it and move the work
to davinci_spi_setup()
Signed-off-by: Brian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: Michael Williamson <michael.williamson@criticallink.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Configure the data-in, data-out and clock functionality pins
in SPIPC0 register only once during probe. No need to set these
bits for each transfer.
Signed-off-by: Brian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: Michael Williamson <michael.williamson@criticallink.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Add support for SPI interrupt mode operation.
Define a per chip-select "io type" variable which
specifies if the transfers on this chip-select should
happen in interrupt mode or polled mode.
Introduce a new function davinci_spi_process_events()
to help consolidate the code between interrupt mode
processing and polled mode processing.
Signed-off-by: Brian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: Michael Williamson <michael.williamson@criticallink.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Use the fact that the get_tx and get_rx can now cope with
NULL buffer pointers to simplify the poll mode transfer
code.
While at it, check for SPI errors every transfer rather than
at the end of the whole transfer.
Signed-off-by: Brian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: Michael Williamson <michael.williamson@criticallink.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
The interrupt mode support as it stands is another version
of poll mode. Even when interrupt mode is selected, the code
tight loops on interrupt status register, rendering it totally
useless. A completion variable is initialized, but never used.
Remove this fake interrupt mode since users can anyway use
poll mode with no functional difference. A usefully implemented
interrupt mode support can be added later.
Signed-off-by: Brian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: Michael Williamson <michael.williamson@criticallink.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
The completion variable 'done' is unnecessarly initialized by
the function davinci_spi_bufs_dma() where as it is not used
for DMA transfers at all.
Remove the unnecessary initialization.
Signed-off-by: Brian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: Michael Williamson <michael.williamson@criticallink.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
In davinci_spi_check_error(), Tx interrupt being set is
treated as error. This function is only meant to flag
bus error conditions and Tx interrupt being set at that
point is not a bus error but rather a driver bug.
Stop checking for Tx interrupt and flagging that as an
IO error.
Tested-By: Michael Williamson <michael.williamson@criticallink.com>
Tested-By: Brian Niebuhr <bniebuhr@efjohnson.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
The variable count in DaVinci SPI driver's private data is
largely unused and its minor use can easily be eliminated.
Remove the variable.
Signed-off-by: Brian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: Michael Williamson <michael.williamson@criticallink.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
In the davinci_spi_bufs_dma() function, SPI is briefly disabled
before enabling it immediately back again.
Remove this unnecessary disable.
Signed-off-by: Brian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: Michael Williamson <michael.williamson@criticallink.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
In the davinci_spi_{tx|rx}_u{8|16}() functions, check for
buffer pointer being valid before using it. While providing
for better error checking, this change will help simplify
code in the caller.
Signed-off-by: Brian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: Michael Williamson <michael.williamson@criticallink.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
The EDMA acount (called data_type in davinci_spi_bufs_dma())
is simply the bytes_per_word obtained in the transfer setup
function. The current code calculates the acount value from
bytes_per_word in a convoluted manner. Simplify the code.
Signed-off-by: Brian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: Michael Williamson <michael.williamson@criticallink.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
The count member of davinci_spi is internal to the driver and
is not shared with framework. Eliminate its unnecessary update.
Signed-off-by: Brian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: Michael Williamson <michael.williamson@criticallink.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
The struct davinci_spi_slave has a single member. Eliminate it
and store the per-chipselect data in struct davinci_spi directly.
Signed-off-by: Brian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: Michael Williamson <michael.williamson@criticallink.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Several members of struct davinci_spi_slave are unused in code.
Remove such members.
Signed-off-by: Brian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: Michael Williamson <michael.williamson@criticallink.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Just enabling WAITENA in SPIFMTn register waits for the
enable signal from the slave indefinitely. Allow support
for finite waiting by adding support for c2e delay
(maximum time for addressed slave to respond) and t2e
delay (maximum time for slave to respond after transmit
data finished).
While at it, modify the T2C and C2T defines by prepending
the register name as is the convention followed for other
register field elsewhere in the driver.
Signed-off-by: Brian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: Michael Williamson <michael.williamson@criticallink.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Setup chip-select timers values only if timer is enabled
(timer_disbled in spi configuration is false).
As a nice side effect, this patch removes code duplicated in
davinci_spi_bufs_pio() and davinci_spi_bufs_dma().
Signed-off-by: Brian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: Michael Williamson <michael.williamson@criticallink.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Consolidate the setup of SPIFMTn register under
davinci_spi_setup_transfer() simplifying the code
and avoiding unnecessary reads and writes to the
register.
The two inline functions {set|clear}_fmt_bits() can
be eliminated because of this.
Signed-off-by: Brian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: Michael Williamson <michael.williamson@criticallink.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Some chip-select specific paramterers like wdelay, parity, usage of
chip-select timers (and the actual timer values) are included in
platform data forcing the same behaviour across all chip-selects.
Create a new davinci_spi_config data structure which can be passed
along using controller_data member of spi_device data structure
on a per-device basis.
Signed-off-by: Brian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: Michael Williamson <michael.williamson@criticallink.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
The SPI_READY bit of struct spi_device:mode serves the purpose
of letting the SPI master know if the slave can signal if it is
ready for transfer or not.
The 'wait_enable' platform data was duplicating this functionality.
Use the framework provided method of indicating this capability.
Signed-off-by: Brian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: Michael Williamson <michael.williamson@criticallink.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Simplify pre-scalar calculation and move it into a seprate
function.
Refuse to correct invalid pre-scalar values silently as this
might lead to unexpected bugs and lower performance. Instead
an error will force users to dig into the root-cause of the
issue.
While at it, remove some device specific checks on the maximum
SPI frequency. As the driver supports the SPI interface
implemented on various devices, it should only take care of core
SPI limitations and leave the device specific handling to platform
code.
Signed-off-by: Brian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: Michael Williamson <michael.williamson@criticallink.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Sometimes, the chip selects provided by SPI module are
muxed with other functionality and cannot be used in
some designs. In such cases, it becomes convenient to use
an available GPIO line as chip select.
This patch enables the DaVinci SPI driver to treat specific
GPIO lines as chip selects based on information provided in
platform data.
Signed-off-by: Brian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: Michael Williamson <michael.williamson@criticallink.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
On TI DaVinci's SPI controller, the SPIDAT1 register which
controls the chip slect status, also has data transmit register
in the lower 16 bits. Writing to the whole 32-bits triggers
an additional data transmit every time the chip select is disabled.
While most SPI slaves cope-up with this, some cannot. This
patch fixes this by doing a 16-bit write on the upper half
of the SPIDAT1 register
While at it, group the SPIGCR1 register related defines seperately
from SPIDAT1 register defines.
Signed-off-by: Brian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: Michael Williamson <michael.williamson@criticallink.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Let davinci_spi_chipselect() perform both activation and
deactivation of chip selects. This lets spi_bitbang fully
control chip select activation, as intended by the SPI API.
With this change, the chip select activation code need not
be duplicated in davinci_spi_bufs_{pio|dma}().
Also, keeping chip select active control is removed as a
platform data and simply controlled using information from
spi_bitbang on whether chip slect should be activated or
de-activated.
Signed-off-by: Brian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: Michael Williamson <michael.williamson@criticallink.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Quit writing the same constant value determining the chip-select
mode when no transmissions are in progress in davinci_spi_chipelect().
Instead just setup the SPIDEF register once during probe.
Signed-off-by: Brian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: Michael Williamson <michael.williamson@criticallink.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
The typecasting of SPI base address to davinci_spi_reg is
unused.
Remove it.
Tested-By: Michael Williamson <michael.williamson@criticallink.com>
Tested-By: Brian Niebuhr <bniebuhr@efjohnson.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Remove unused defines from code which should help
in easy reading of code.
Also, use the opportuinity to keep the SPIGCR1
register defines together.
Tested-By: Michael Williamson <michael.williamson@criticallink.com>
Tested-By: Brian Niebuhr <bniebuhr@efjohnson.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
The 'pdata' variable is unused in couple of routines.
Remove such occurences.
Signed-off-by: Brian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: Michael Williamson <michael.williamson@criticallink.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Cleanup unnecessary white space from various
parts of the file.
Signed-off-by: Brian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: Michael Williamson <michael.williamson@criticallink.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Fix the following checkpatch error:
WARNING: unnecessary whitespace before a quoted newline
+ dev_info(&pdev->dev, "Controller at 0x%p \n", davinci_spi->base);
Signed-off-by: Brian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: Michael Williamson <michael.williamson@criticallink.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Now that the of_platform_bus_type has been merged with the platform
bus type, a single platform driver can handle both OF and non-OF use
cases. This patch merges the OF support into the platform driver.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Tested-by: Michal Simek <monstr@monstr.eu>
This patch merges the platform driver support into the main body of
xilinx_spi.c in preparation for merging the OF and non-OF support
code.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Tested-by: Michal Simek <monstr@monstr.eu>
The current code has the OF binding modifying the platform_data
pointer which it must not do, and the common code doesn't really need
to use a pdata pointer. This patch eliminates the platform_data
references from the common part of the driver in preparation for
merging the OF and non-OF versions.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Tested-by: Michal Simek <monstr@monstr.eu>
* 'next-spi' of git://git.secretlab.ca/git/linux-2.6:
spi/pl022: fix erroneous platform data in U300
spi: fixed odd static string conventions in core code
spi/bfin_spi: only request GPIO on first load
spi/bfin_spi: handle error/status changes after data interrupts
spi: enable spi_board_info to be registered after spi_master
* 'llseek' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/bkl:
vfs: make no_llseek the default
vfs: don't use BKL in default_llseek
llseek: automatically add .llseek fop
libfs: use generic_file_llseek for simple_attr
mac80211: disallow seeks in minstrel debug code
lirc: make chardev nonseekable
viotape: use noop_llseek
raw: use explicit llseek file operations
ibmasmfs: use generic_file_llseek
spufs: use llseek in all file operations
arm/omap: use generic_file_llseek in iommu_debug
lkdtm: use generic_file_llseek in debugfs
net/wireless: use generic_file_llseek in debugfs
drm: use noop_llseek
This patch removes convention of passing a static string as a
parameter to another static string. The convention is intended to
reduce text usage by sharing the common bits of the string, but the
implementation is inherently fragile (a change to one format string
but not the other will nullify any possible advantage), it isn't
necessarily a net win depending on what this compiler does, and it
it reduces code readability.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
[grant.likely@secretlab.ca: removed dev_dbg->dev_err hunk]
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The gpiolib code does not allow people to do gpio_request() on a GPIO
once it has already been requested. So make sure we only request the
pin on the first setup of a SPI device. Otherwise, if you attempts to
reconfigure a SPI device on the fly (like change bit sizes), the setup
function incorrectly fails.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The error interrupt on the BF537 SIC cannot be enabled on a
per-peripheral basis. Once the error interrupt is enabled
for one peripheral, it is automatically enabled for all.
So in the Blackfin on-chip SPI driver, we need to clear out
these known errors in the data interrupt once we've successfully
finished processing all of the pending data.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Currently spi_register_board_info() has to be called before its related
spi_master be registered, otherwise these board info will be just ignored.
This patch will remove this order limit, it adds a global spi master list
like the existing global board info listr. Whenever a board info or a
spi_master is registered, the spi master list or board info list
will be scanned, and a new spi device will be created if there is a
master-board info match.
Signed-off-by: Feng Tang <feng.tang@intel.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
v2 changes:
from Thierry Reding:
* add "select TEGRA_SYSTEM_DMA" to Kconfig
from Grant Likely:
* add oneline description to header
* inline references to DRIVER_NAME
* inline references to BUSY_TIMEOUT
* open coded bytes_per_word()
* spi_readl/writel -> spi_tegra_readl/writel
* move transfer validation to spi_tegra_transfer
* don't request_mem_region iomem as platform bus does that for us
* __exit -> __devexit
v3 changes:
from Russell King:
* put request_mem_region back int
from Grant Likely:
* remove #undef DEBUG
* add SLINK_ to register bit defines
* remove unused bytes_per_word
* make spi_tegra_readl/writel static linine
* various refactoring for clarity
* mark err if BSY bit is not cleared after 1000 retries
* move spinlock to protect setting of RDY bit
* subsys_initcall -> module_init
v3 changes:
from Grant Likely:
* update spi_tegra to use PTR_ERRless dma API
v4 changes:
from Grant Likely:
* remove empty spi_tegra_cleanup fucntion
* allow device ids of -1
Signed-off-by: Erik Gilling <konkers@android.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Cc: Thierry Reding <thierry.reding@avionic-design.de>
Cc: Russell King <linux@arm.linux.org.uk>
spi: tegra: cleanups from upstream review
Change-Id: Icecf7e64efcb39de072a15234ba1faa4bad40d25
Signed-off-by: Erik Gilling <konkers@android.com>
* 'devel' of master.kernel.org:/home/rmk/linux-2.6-arm: (278 commits)
arm: remove machine_desc.io_pg_offst and .phys_io
arm: use addruart macro to establish debug mappings
arm: return both physical and virtual addresses from addruart
arm/debug: consolidate addruart macros for CONFIG_DEBUG_ICEDCC
ARM: make struct machine_desc definition coherent with its comment
eukrea_mbimxsd-baseboard: Pass the correct GPIO to gpio_free
cpuimx27: fix compile when ULPI is selected
mach-pcm037_eet: fix compile errors
Fixing ethernet driver compilation error for i.MX31 ADS board
cpuimx51: update board support
mx5: add cpuimx51sd module and its baseboard
iomux-mx51: fix GPIO_1_xx 's IOMUX configuration
imx-esdhc: update devices registration
mx51: add resources for SD/MMC on i.MX51
iomux-mx51: fix SD1 and SD2's iomux configuration
clock-mx51: rename CLOCK1 to CLOCK_CCGR for better readability
clock-mx51: factorize clk_set_parent and clk_get_rate
eukrea_mbimxsd: add support for DVI displays
cpuimx25 & cpuimx35: fix OTG port registration in host mode
i.MX31 and i.MX35 : fix errate TLSbo65953 and ENGcm09472
...
In case of TX only with DMA, the driver assumes that the data
has been transferred once DMA callback in invoked. However,
SPI's shift register may still contain data. Thus, the driver
is supposed to verify that the register is empty and the end of
the SPI transfer has been reached.
Signed-off-by: Ilkka Koskinen <ilkka.koskinen@nokia.com>
Tested-by: Tuomas Katila <ext-tuomas.2.katila@nokia.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
In the TX_ONLY transfer, the SPI controller also receives data
simultaneously and saves them in the rx register. After the TX_ONLY
transfer, the rx register will hold the random data received during
the last tx transaction.
If the direct following transfer is RX_ONLY, this random data has the
possibility to affect this transfer like this:
When the SPI controller is changed from TX_ONLY to RX_ONLY,
the random data makes the rx register full immediately and
triggers a dummy write automatically(in SPI RX_ONLY transfers,
we need a dummy write to trigger the first transaction).
So the first data received in the RX_ONLY transfer will be that
random data instead of something meaningful.
We can avoid this by inserting a Disable/Re-enable toggle of the
channel after the TX_ONLY transfer, since it purges the rx register.
Signed-off-by: Jason Wang <jason77.wang@gmail.com>
Tested-by: Grazvydas Ignotas <notasas@gmail.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Some systems using this bus sometimes have very basic devices on them
such as regulators. So we need to be loaded even earlier in case the
devices are used by things such as early board init code. Therefore
register in subsys_initcall().
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Currently, if the bits_per_word when doing a transfer is not 8bits, we
always treat it as 16bits when we should actually be returning an error.
Signed-off-by: Bob Liu <lliubbo@gmail.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
When the hardware is controlling the CS, there are some SPI options
we are unable to support. So issue a warning in the hopes that the
user will change to a SPI mode where we can support things sanely.
Signed-off-by: Barry Song <barry.song@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Using disable_irq() on the IRQ whose handler we are currently executing in
can easily lead to a hang. So use the nosync variant here.
Signed-off-by: Barry Song <barry.song@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
While combining things, also switch to the proper SPI bit define names.
This lets us punt the rarely used SPI defines.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
During runtime, the spi setup function may be called multiple times on the
same device in order to reconfigure some settings on the fly. When this
happens, we need to reset the ctl_reg bits so that changing the mode works
as expected.
Reported-by: Andy Getzendanner <james.getzendanner@students.olin.edu>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
This reduces duplication between the setup/transfer functions and keeps
values cached during setup from overriding values changed on a transfer
basis (like bits_per_word).
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Using disable_irq() on the IRQ whose handler we are currently executing in
can easily lead to a hang. So use the nosync variant here.
Signed-off-by: Yi Li <yi.li@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Sometimes under load, the Blackfin core is able to send SPI register
updates out before the controller is actually disabled. So when we
go to reprogram the entire state (to switch to a different slave),
make sure we sync after disabling the controller.
Signed-off-by: Barry Song <barry.song@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
We can't rely on the SPI_CTL/SPI_FLG registers retaining their state when
suspending, so save/restore their entire values.
Signed-off-by: Barry Song <barry.song@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The common SPI layers take care of detecting CS conflicts and preventing
two devices from claiming the same CS. This causes problems for the GPIO
CS support we currently have as we are using CS0 to mean "GPIO CS". But
if we have multiple devices using a GPIO CS, the common SPI layers see
multiple devices using the virtual "CS0" and reject any such attempts.
To make both work, we introduce an offset define. This represents the
max number of hardware CS values that the SPI peripheral supports. If
the CS is below this limit, we know we can use the hardware CS. If it's
above, we treat it as a GPIO CS. This keeps the CS unique as seen by
the common code and prevents conflicts.
Signed-off-by: Barry Song <barry.song@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The driver that we based ours on uses a little extra memory behind the
normal driver state, but we don't. So drop this useless bit of memory.
Reported-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The current structure names are a bit confusing as to what they represent,
so use better names.
Reported-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Rather than having to look up the same 3 sets of functions at the same
time, just use an ops structure so we only need to set one pointer.
Reported-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
No point in creating our own version of true/false defines when there is
already a standard stdbool available to us.
Reported-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The chip ops should always be initialized, so having null fallback
functions are useless.
Reported-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
As David points out, the cs_change_per_word option isn't standard, nor is
anyone actually using it. So punt all of the dead code considering it
makes up ~10% of the code size.
Reported-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The CS helper functions were toggling both the Flag Enable and the Flag
Value bits, but the Flag Value bit is ignored if the corresponding Flag
Enable bit is cleared. So under high speed transactions, the CS sometimes
would not toggle properly.
Since it makes no sense to toggle the Flag Enable bit dynamically when we
actually want to control the Flag Value, do this when setting up the device
and then only handle toggling of the CS value during runtime.
Signed-off-by: Barry Song <barry.song@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The current behavior in PIO mode is to poll the SPI status registers which
can obviously lead to higher latencies when doing a lot of SPI traffic.
There is a SPI interrupt which can be used instead to signal individual
completion of transactions.
Signed-off-by: Yi Li <yi.li@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
We should make sure the SPI controller is in a sane state in case the
boot loader left it in a crappy state. Such as DMA pending which causes
interrupts to fire on us.
When setting a sane initial state, do not default to slave mode. If we
do, then the SPI peripheral may implicitly take over the SPISS pin which
other things might be using.
For example, the BF533-STAMP uses this pin as a GPIO to control switching
between ethernet and flash. If the SPI peripheral controls the output
state instead, the ethernet is no longer accessible.
URL: http://blackfin.uclinux.org/gf/tracker/5630
Signed-off-by: Wolfgang Muees <wolfgang.mues@auerswald.de>
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Anomaly 05000119 states that the DMA_RUN bit with peripherals isn't
reliable. However, the way the driver is currently written (DMA IRQ
callback), we don't need the polling in the first place, so drop it.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Re-order setup() a bit so we don't leak memory/dma/gpio resources upon
errors. Also make sure we don't call kfree() twice on the same object.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Yi Li <yi.li@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
This patches a typo in the debug message.
Signed-off-by: Matthias Brugger <mensch0815@gmail.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
All file_operations should get a .llseek operation so we can make
nonseekable_open the default for future file operations without a
.llseek pointer.
The three cases that we can automatically detect are no_llseek, seq_lseek
and default_llseek. For cases where we can we can automatically prove that
the file offset is always ignored, we use noop_llseek, which maintains
the current behavior of not returning an error from a seek.
New drivers should normally not use noop_llseek but instead use no_llseek
and call nonseekable_open at open time. Existing drivers can be converted
to do the same when the maintainer knows for certain that no user code
relies on calling seek on the device file.
The generated code is often incorrectly indented and right now contains
comments that clarify for each added line why a specific variant was
chosen. In the version that gets submitted upstream, the comments will
be gone and I will manually fix the indentation, because there does not
seem to be a way to do that using coccinelle.
Some amount of new code is currently sitting in linux-next that should get
the same modifications, which I will do at the end of the merge window.
Many thanks to Julia Lawall for helping me learn to write a semantic
patch that does all this.
===== begin semantic patch =====
// This adds an llseek= method to all file operations,
// as a preparation for making no_llseek the default.
//
// The rules are
// - use no_llseek explicitly if we do nonseekable_open
// - use seq_lseek for sequential files
// - use default_llseek if we know we access f_pos
// - use noop_llseek if we know we don't access f_pos,
// but we still want to allow users to call lseek
//
@ open1 exists @
identifier nested_open;
@@
nested_open(...)
{
<+...
nonseekable_open(...)
...+>
}
@ open exists@
identifier open_f;
identifier i, f;
identifier open1.nested_open;
@@
int open_f(struct inode *i, struct file *f)
{
<+...
(
nonseekable_open(...)
|
nested_open(...)
)
...+>
}
@ read disable optional_qualifier exists @
identifier read_f;
identifier f, p, s, off;
type ssize_t, size_t, loff_t;
expression E;
identifier func;
@@
ssize_t read_f(struct file *f, char *p, size_t s, loff_t *off)
{
<+...
(
*off = E
|
*off += E
|
func(..., off, ...)
|
E = *off
)
...+>
}
@ read_no_fpos disable optional_qualifier exists @
identifier read_f;
identifier f, p, s, off;
type ssize_t, size_t, loff_t;
@@
ssize_t read_f(struct file *f, char *p, size_t s, loff_t *off)
{
... when != off
}
@ write @
identifier write_f;
identifier f, p, s, off;
type ssize_t, size_t, loff_t;
expression E;
identifier func;
@@
ssize_t write_f(struct file *f, const char *p, size_t s, loff_t *off)
{
<+...
(
*off = E
|
*off += E
|
func(..., off, ...)
|
E = *off
)
...+>
}
@ write_no_fpos @
identifier write_f;
identifier f, p, s, off;
type ssize_t, size_t, loff_t;
@@
ssize_t write_f(struct file *f, const char *p, size_t s, loff_t *off)
{
... when != off
}
@ fops0 @
identifier fops;
@@
struct file_operations fops = {
...
};
@ has_llseek depends on fops0 @
identifier fops0.fops;
identifier llseek_f;
@@
struct file_operations fops = {
...
.llseek = llseek_f,
...
};
@ has_read depends on fops0 @
identifier fops0.fops;
identifier read_f;
@@
struct file_operations fops = {
...
.read = read_f,
...
};
@ has_write depends on fops0 @
identifier fops0.fops;
identifier write_f;
@@
struct file_operations fops = {
...
.write = write_f,
...
};
@ has_open depends on fops0 @
identifier fops0.fops;
identifier open_f;
@@
struct file_operations fops = {
...
.open = open_f,
...
};
// use no_llseek if we call nonseekable_open
////////////////////////////////////////////
@ nonseekable1 depends on !has_llseek && has_open @
identifier fops0.fops;
identifier nso ~= "nonseekable_open";
@@
struct file_operations fops = {
... .open = nso, ...
+.llseek = no_llseek, /* nonseekable */
};
@ nonseekable2 depends on !has_llseek @
identifier fops0.fops;
identifier open.open_f;
@@
struct file_operations fops = {
... .open = open_f, ...
+.llseek = no_llseek, /* open uses nonseekable */
};
// use seq_lseek for sequential files
/////////////////////////////////////
@ seq depends on !has_llseek @
identifier fops0.fops;
identifier sr ~= "seq_read";
@@
struct file_operations fops = {
... .read = sr, ...
+.llseek = seq_lseek, /* we have seq_read */
};
// use default_llseek if there is a readdir
///////////////////////////////////////////
@ fops1 depends on !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier readdir_e;
@@
// any other fop is used that changes pos
struct file_operations fops = {
... .readdir = readdir_e, ...
+.llseek = default_llseek, /* readdir is present */
};
// use default_llseek if at least one of read/write touches f_pos
/////////////////////////////////////////////////////////////////
@ fops2 depends on !fops1 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier read.read_f;
@@
// read fops use offset
struct file_operations fops = {
... .read = read_f, ...
+.llseek = default_llseek, /* read accesses f_pos */
};
@ fops3 depends on !fops1 && !fops2 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier write.write_f;
@@
// write fops use offset
struct file_operations fops = {
... .write = write_f, ...
+ .llseek = default_llseek, /* write accesses f_pos */
};
// Use noop_llseek if neither read nor write accesses f_pos
///////////////////////////////////////////////////////////
@ fops4 depends on !fops1 && !fops2 && !fops3 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier read_no_fpos.read_f;
identifier write_no_fpos.write_f;
@@
// write fops use offset
struct file_operations fops = {
...
.write = write_f,
.read = read_f,
...
+.llseek = noop_llseek, /* read and write both use no f_pos */
};
@ depends on has_write && !has_read && !fops1 && !fops2 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier write_no_fpos.write_f;
@@
struct file_operations fops = {
... .write = write_f, ...
+.llseek = noop_llseek, /* write uses no f_pos */
};
@ depends on has_read && !has_write && !fops1 && !fops2 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier read_no_fpos.read_f;
@@
struct file_operations fops = {
... .read = read_f, ...
+.llseek = noop_llseek, /* read uses no f_pos */
};
@ depends on !has_read && !has_write && !fops1 && !fops2 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
@@
struct file_operations fops = {
...
+.llseek = noop_llseek, /* no read or write fn */
};
===== End semantic patch =====
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Julia Lawall <julia@diku.dk>
Cc: Christoph Hellwig <hch@infradead.org>
We get the following when building on ppc64 due to lack of include of
<asm/io.h>:
In file included from drivers/spi/spi_fsl_espi.c:25:0:
drivers/spi/spi_fsl_lib.h: In function 'mpc8xxx_spi_write_reg':
drivers/spi/spi_fsl_lib.h:88:2: error: implicit declaration of function 'out_be32'
drivers/spi/spi_fsl_lib.h: In function 'mpc8xxx_spi_read_reg':
drivers/spi/spi_fsl_lib.h:93:2: error: implicit declaration of function 'in_be32'
drivers/spi/spi_fsl_espi.c: In function 'fsl_espi_remove':
drivers/spi/spi_fsl_espi.c:571:2: error: implicit declaration of function 'iounmap'
drivers/spi/spi_fsl_espi.c: In function 'fsl_espi_probe':
drivers/spi/spi_fsl_espi.c:602:2: error: implicit declaration of function 'ioremap'
drivers/spi/spi_fsl_espi.c:602:24: warning: assignment makes pointer from integer without a cast
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
bits_per_word option in spi_transfer are allowed if it does not change
the csr register.
This is necessary for the driver in
drivers/staging/iio/adis16260_core.c, as it uses this option.
Signed-off-by: Matthias Brugger <mensch0815@gmail.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This patch fixes the following build error introduced by commit
65308c46, "spi/topcliff: cleanup for style and conciseness".
drivers/spi/spi_topcliff_pch.c: In function 'pch_spi_process_messages':
drivers/spi/spi_topcliff_pch.c:752: warning: 'data' is used uninitialized in
+this function
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Add eSPI controller support based on the library code spi_fsl_lib.c.
The eSPI controller is newer controller 85xx/Pxxx devices supported.
There're some differences comparing to the SPI controller:
1. Has different register map and different bit definition
So leave the code operated the register to the driver code, not
the common code.
2. Support 4 dedicated chip selects
The software can't controll the chip selects directly, The SPCOM[CS]
field is used to select which chip selects is used, and the
SPCOM[TRANLEN] field is set to tell the controller how long the CS
signal need to be asserted. So the driver doesn't need the chipselect
related function when transfering data, just set corresponding register
fields to controll the chipseclect.
3. Different Transmit/Receive FIFO access register behavior
For SPI controller, the Tx/Rx FIFO access register can hold only
one character regardless of the character length, but for eSPI
controller, the register can hold 4 or 2 characters according to
the character lengths. Access the Tx/Rx FIFO access register of the
eSPI controller will shift out/in 4/2 characters one time. For SPI
subsystem, the command and data are put into different transfers, so
we need to combine all the transfers to one transfer in order to pass
the transfer to eSPI controller.
4. The max transaction length limitation
The max transaction length one time is limitted by the SPCOM[TRANSLEN]
field which is 0xFFFF. When used mkfs.ext2 command to create ext2
filesystem on the flash, the read length will exceed the max value of
the SPCOM[TRANSLEN] field.
Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Refactor the common code in file spi_fsl_spi.c to spi_fsl_lib.c used
by SPI/eSPI controller driver as a library, and leave the QE/CPM SPI
controller code in the SPI controller driver spi_fsl_spi.c.
Because the register map of the SPI controller and eSPI controller
is so different, also leave the code operated the register to the
driver code, not the common code.
Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This will pave the way to refactor out the common code which can be used
by the eSPI controller driver, and rename the SPI controller dirver to the
file spi_fsl_spi.c.
Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This removes some dubious allocation of a local chipinfo struct
in favor of a constant preset, tagging that one const revealed
further problems with platform data being modified so fixed up
these too.
Reported-by: Virupax Sadashivpetimath <virupax.sadashivpetimath@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
What is the dev pointer doing inside the platform data anyway.
We have another pointer to the actual device at hand, use that.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This patch adds spi->mode support for the AMBA pl022 driver and
allows spidev to correctly alter SPI modes. Unused fields used in
the pl022 header file for the pl022_config_chip have been removed.
The ab8500 client driver selects the data transfer size instead
of the platform data.
For platforms that use the amba pl022 driver, the unused fields
in the controller data structure have been removed and the .mode
field in the SPI board info structure is used instead.
Signed-off-by: Kevin Wells <wellsk40@gmail.com>
Tested-by: Linus Walleij <linus.walleij@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This extends the PL022 SSP/SPI driver with generic DMA engine
support using the PrimeCell DMA engine interface. Also fix up the
test code for the U300 platform.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This patch makes multiple cleanups to the new topcliff pch spi driver
including, but not limited to,
- removing superfluous brackets around variables
- open coding functions that are only used once
- removing unnecessary line breaks
- removing unused functions
- simplifying the interrupt enable/disable code
- remove unnecessary (void *) casts.
- remove b_mem_fail from pch_spi_set_tx to code it more cleanly
- shorten dev_dbg() messages for conciseness and readability
More cleanups are still needed in this driver. In particular,
- the driver filename should be changed to spi_topcliff_pch.c
- many of the dev_dbg() lines should be trimmed (particularly the ones
on unconditional code paths).
- I suspect that the locking model not correct. I'd like to know what
drivers' critical regions are, and how they are protected.
- get_resources and release_resources probably should be open coded in
.probe and .release respectively.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The i.MX51 ECSPI has a fifo size of 64 entries instead of 8 entries as
found on the other cspi bus devices.
Cc: Jason Wang <jason77.wang@gmail.com>
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Topcliff PCH is the platform controller hub that is going to be used
in Intel's upcoming general embedded platform. All IO peripherals in
Topcliff PCH are actually devices sitting on AMBA bus. This patch
adds a driver for the SPI bus integrated into the Topcliff device.
Signed-off-by: Masayuki Ohtake <masa-korg@dsn.okisemi.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This patch adds the OF hook to the spi core so that devices
can automatically be registered based on device tree data. This fixes
a problem with spi devices not binding to drivers after the cleanup of
the spi & i2c binding code.
Signed-off-by: Sinan Akman <sinan@writeme.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The SPI_MASTER_NO_TX bit (can't do buffer write) wasn't tested. This
code was introduced in commit 3c8e1a84 (spi/spi-gpio: add support for
controllers without MISO or MOSI pin). This patch fixes a bug in
choosing which transfer ops to use.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
i.MX51 comes with two eCSPI interfaces (that are quite different from
what was known before---the tried and tested Freescale way) and a CSPI
interface that is identical to the devices found on i.MX25 and i.MX35.
This patch is a merge of two very similar patches (by Jason Wang and Sascha
Hauer resp.) plus a (now hopefully correct) reimplementation of the
clock calculation.
Acked-by: Jason Wang <jason77.wang@gmail.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This prepares adding support for imx51's eCSPI. This IP has seperate
control and config bits for all four supported chip selects, so the
config routine needs to know which chip select is being used even if
the chipselect is realized by a gpio.
Acked-by: Jason Wang <jason77.wang@gmail.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Nearly everything that is needed is provided by the version of the SPI IP.
Now the only checks left using cpu_is_... are clk divider tuning on mx21/mx27
and autodetection (which will die soon).
Acked-by: Jason Wang <jason77.wang@gmail.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This has the advantage not to need to much cpu_is_... macros. Still more
when imx51 support is added which has two different spi interfaces which
would introduce additional checks on the device id.
With this setup it's not possible for the compiler anymore to detect the
unused functions, so four additional kconfig symbols are introduced to
ifdef out the unneeded functions in the callback array and all these
functions are marked with __maybe_unused to suppress the corresponding
gcc warnings.
Comparing the driver footprint with and without the patch for a mx27
kernel yields:
add/remove: 2/0 grow/shrink: 2/0 up/down: 280/0 (280)
function old new delta
spi_imx_devtype - 192 +192
spi_imx_probe 980 1032 +52
spi_imx_devtype_data - 32 +32
spi_imx_setupxfer 276 280 +4
Later when the platform code is updated to use the platform ids, the
autodetection can be removed which will make the driver a bit smaller
again. (~60 Bytes in my test.)
Acked-by: Jason Wang <jason77.wang@gmail.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
We can't do without setting channel and bus width to
same size. In order to do that, use loop read/writes in
polling mode and appropriate burst size in DMA mode.
Signed-off-by: Jassi Brar <jassi.brar@samsung.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Newer SoCs have the SPI clock scaling control in platform's
clock management unit. Inorder for such SoCs to work, we need
to check the flag clk_from_cmu before making any clock changes.
Signed-off-by: Jassi Brar <jassi.brar@samsung.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Since we use DMA mode only for xfers bigger than FIFO size,
do not map/unmap buffers for polling mode transfers.
Signed-off-by: Jassi Brar <jassi.brar@samsung.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The return -EINVAL appears to only make sense if the if branch that it is
aligned with is taken, and the indentation indicates that this is the
authors intent, so move it into that branch.
The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r disable braces4@
position p1,p2;
statement S1,S2;
@@
(
if (...) { ... }
|
if (...) S1@p1 S2@p2
)
@script:python@
p1 << r.p1;
p2 << r.p2;
@@
if (p1[0].column == p2[0].column):
cocci.print_main("branch",p1)
cocci.print_secs("after",p2)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
list_for_each_entry binds its first argument to a non-null value, and thus
any null test on the value of that argument is superfluous.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
iterator I;
expression x,E;
@@
I(x,...) { <...
- (x != NULL) &&
E
...> }
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
dev_vdbg() is only compiled when VERBOSE is defined, so
there's no need to wrap dev_dbg() on #ifdef VERBOSE .. #endif
as we can use dev_vdbg() directly.
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
It fixes an issue when sending-only or receiving-only more than
PAGE_SIZE bytes.
Signed-off-by: christophe leroy <christophe.leroy@c-s.fr>
Acked-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The PL022 SPI bus is sometimes used for early stuff like
regulators that need to be present at module_init() time, so
we move this to a subsys_initcall().
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
With the introduction of an AMBA PrimeCell per-cell block clock,
the pclk was left on after probe() unless explicitly disabled.
This clock is wired to the same clock on PL022 causing it to stay
always on since.
Fix this up properly by clocking the pclk whenever we want to
write into any PL022 registers and clocking the external clock
whenever we want to transmit messages on the bus.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Tested-by : Kevin Wells <wellsk40@gmail.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
When using PIO we have a timeout for the TX and RX FIFOs to ensure that
the data actually gets transferred. Warn if we hit that timeout - it
should never happen, but this makes sure we'll find out if it does.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Jassi Brar <jassi.brar@samsung.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Instead of, wrongly, reusing the 'val' variable, use a dedicated
one for reading the status register.
Signed-off-by: Jassi Brar <jassi.brar@samsung.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Fix compilation warning by typecasting the tx_buf pointer.
[I'm not thrilled with resorting to a cast; but I cannot see a better
way to go about this. I don't want to drop the const from struct
spi_transfer ~~glikely]
Signed-off-by: Jassi Brar <jassi.brar@samsung.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
commit 052dc7c45i "spi/dw_spi: conditional transfer mode change"
introduced cs_control code, which has a bug by using bit offset
for spi mode to set transfer mode in control register. Also it
forces devices who don't need cs_control to re-configure the
control registers for each spi transfer. This patch will fix them
Signed-off-by: Feng Tang <feng.tang@intel.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Allow interrupt sharing since exclusive interrupt line for
DW SPI controller is not provided on every platform.
Signed-off-by: Yong Wang <yong.y.wang@intel.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
For small transfers at high speeds the expected transfer time can easily
be well under 1ms, causing the delay in wait_for_xfer() to be only the
dead reckoning fudge factor of 5ms currently included. Experiments on
some of my systems shows that this is marginal for some transfers so
double it to 10ms.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Jassi Brar <jassi.brar@samsung.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Allow the use of the S3C64xx SPI controller with things like PMICs by
moving the init up to subsys_initcall().
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Jassi Brar <jassi.brar@samsung.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
introduced by 49dce689 ("spi doesn't need class_device") and bad-fixed
by 350d0076 ("spi: fix double-free on spi_unregister_master"),
spi_unregister_master would previously device_unregister all of the spi
master's siblings (instead of its children). hilarity ensues.
fix it to unregister children.
Signed-off-by: David Lamparter <equinox@diac24.net>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Jassi Brar <jassisinghbrar@gmail.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The S3C64xx SPI driver requires the machine to call s3c64xx_spi_set_info()
to select a few options, including the clock to use for the SPI controller.
If this is not done then a NULL will be passed as the clock name for
clk_get(), causing an obscure crash. Guard against this and other missing
configuration by validating that the clock name has been filled in in
the platform data that ets passed in.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Using the coldfire qspi driver, I get the following error:
drivers/spi/coldfire_qspi.c: In function 'mcfqspi_irq_handler':
drivers/spi/coldfire_qspi.c:166: error: 'TASK_NORMAL' undeclared (first use in this function)
drivers/spi/coldfire_qspi.c:166: error: (Each undeclared identifier is reported only once
It is solved by adding the following include to coldfire_sqpi.c:
#include <linux/sched.h>
Fix suggested by Jate Sujjavanich <jsujjavanich@syntech-fuelmaster.com>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
* 'next-spi' of git://git.secretlab.ca/git/linux-2.6:
spi/amba_pl022: Fix probe and remove hook section annotations.
spi/mpc5121: change annotations for probe and remove functions
spi/bitbang: reinitialize transfer parameters for every message
spi/spi-gpio: add support for controllers without MISO or MOSI pin
spi/bitbang: add support for SPI_MASTER_NO_{TX, RX} modes
SPI100k: Fix 8-bit and RX-only transfers
spi/mmc_spi: mmc_spi adaptations for SPI bus locking API
spi/mmc_spi: SPI bus locking API, using mutex
Fix trivial conflict in drivers/spi/mpc512x_psc_spi.c due to 'struct
of_device' => 'struct platform_device' rename and __init/__exit to
__devinit/__devexit fix.
of_device is just an alias for platform_device, so remove it entirely. Also
replace to_of_device() with to_platform_device() and update comment blocks.
This patch was initially generated from the following semantic patch, and then
edited by hand to pick up the bits that coccinelle didn't catch.
@@
@@
-struct of_device
+struct platform_device
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Reviewed-by: David S. Miller <davem@davemloft.net>
This patch moves the declaration of of_get_address(), of_get_pci_address(),
and of_pci_address_to_resource() out of arch code and into the common
linux/of_address header file.
This patch also fixes some of the asm/prom.h ordering issues. It still
includes some header files that it ideally shouldn't be, but at least the
ordering is consistent now so that of_* overrides work.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Probe and remove hooks belong in the __devinit and __devexit sections
respectively. This patch fixes incorrect annotations on the pl022 spi
driver.
Signed-off-by: Kevin Wells <wellsk40@gmail.com>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Move of_register_spi_devices() call from drivers to
spi_register_master(). Also change the function to use
the struct device_node pointer from master spi device
instead of passing it as function argument.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
