Commit Graph

78 Commits

Author SHA1 Message Date
Vladimir Zapolskiy
a3781639e1 rtc: cmos: clean up cmos_nvram_read()/cmos_nvram_write()
The change removes redundant sysfs binary file boundary checks, since
this task is already done on caller side in fs/sysfs/file.c

Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
2015-09-05 13:19:09 +02:00
Adrian Huang
8109d44f76 rtc: cmos: Revert "rtc-cmos: Add an alarm disable quirk"
Commit d5a1c7e3fc ("rtc-cmos: Add an alarm disable quirk") that
added a special quirk is not needed because [PATCH 1/2] of this
patchset makes the kernel more robust:
rtc-cmos: Cancel alarm timer if alarm time is equal to now+1 seconds

Signed-off-by: Adrian Huang <ahuang12@lenovo.com>
Tested-by: Egbert Eich <eich@suse.de>
Tested-by: Diego Ercolani <diego.ercolani@gmail.com>
Cc: Borislav Petkov <bp@suse.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
2015-09-05 13:19:08 +02:00
Adrian Huang
88b8d33b1c rtc: cmos: Cancel alarm timer if alarm time is equal to now+1 seconds
Steps to reproduce the problem:
	1) Enable RTC wake-up option in BIOS Setup
	2) Issue one of these commands in the OS: "poweroff"
	   or "shutdown -h now"
	3) System will shut down and then reboot automatically

Root-cause of the issue:
	1) During the shutdown process, the hwclock utility is used
	   to save the system clock to hardware clock (RTC).
	2) The hwclock utility invokes ioctl() with RTC_UIE_ON. The
	   kernel configures the RTC alarm for the periodic interrupt
	   (every 1 second).
	3) The hwclock uitlity closes the /dev/rtc0 device, and the
	   kernel disables the RTC alarm irq (AIE bit of Register B)
	   via ioctl() with RTC_UIE_OFF. But, the configured alarm
	   time is the current_time + 1.
	4) After the next 1 second is elapsed, the AF (alarm
	   interrupt flag) of Register C is set.
	5) The S5 handler in BIOS is invoked to configure alarm
	   registers (enable AIE bit and configure alarm date/time).
	   But, BIOS does not clear the previous interrupt status
	   during alarm configuration. Therefore, "AF=AIE=1" causes
	   the rtc device to trigger an interrupt.
	6) So, the machine reboots automatically right after shutdown.

This patch cancels the alarm timer if the following condictions are
met (suggested by Alexandre):
	1) The configured alarm time is equal to current_time + 1
	   seconds.
	2) The AIE timer is not in use.

The member 'alarm_expires' is introduced in struct cmos_rtc because
of the following reasons:
	1) The configured alarm time can be retrieved from
	   cmos_read_alarm(), but we need to take the 'wrapped
	   timestamp' and 'time rollover' into consideration. The
	   function __rtc_read_alarm() eliminates the concerns. To
	   avoid the duplicated code in the lower level RTC driver,
	   invoking __rtc_read_alarm from the lower level RTC driver
	   is not encouraged. Moreover, the compilation error 'the
	   undefined __rtc_read_alarm" is observed if the lower level
	   RTC driver is compiled as a kernel module.
	2) The uie_rtctimer.node.expires and aie_timer.node.expires can
	   be retrieved for the configured alarm time. But, the problem
	   is that either of them might configure the CMOS alarm time.
	   We cannot make sure UIE timer or AIE tiemr configured the
	   CMOS alarm time before. (uie_rtctimer or aie_timer is enabled
	   and then is disabled).
	3) The patch introduces the member 'alarm_expires' to keep the
	   newly configured alarm time, so the above-mentioned concerns
	   can be eliminated.

The issue goes away after 20-time shutdown tests.

Signed-off-by: Adrian Huang <ahuang12@lenovo.com>
Tested-by: Egbert Eich <eich@suse.de>
Tested-by: Diego Ercolani <diego.ercolani@gmail.com>
Cc: Borislav Petkov <bp@suse.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
2015-09-05 13:19:08 +02:00
Joe Perches
a737e835e5 rtc: use more standard kernel logging styles
Neaten the logging a bit by adding #define pr_fmt

Miscellanea:

o Remove __FILE__/__func__ uses
o Coalesce formats adding missing spaces
o Align arguments
o (rtc-cmos) Integrated 2 consecutive messages

Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Joshua Kinard <kumba@gentoo.org>
Cc: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Tested-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Cc: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2015-04-17 09:04:02 -04:00
Joe Perches
4395eb1f16 rtc: remove use of seq_printf return value
The seq_printf return value, because it's frequently misused,
will eventually be converted to void.

See: commit 1f33c41c03 ("seq_file: Rename seq_overflow() to
     seq_has_overflowed() and make public")

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2015-04-15 16:35:24 -07:00
Daniel Glöckner
a882b14fe8 rtc-cmos: fix wakeup from S5 without CONFIG_PM_SLEEP
Commit b5ada4600d ("drivers/rtc/rtc-cmos.c: fix compilation warning
when !CONFIG_PM_SLEEP") broke wakeup from S5 by making cmos_poweroff a
nop unless CONFIG_PM_SLEEP was defined.

Fix this by restricting the #ifdef to cmos_resume and restoring the old
dependency on CONFIG_PM for cmos_suspend and cmos_poweroff.

Signed-off-by: Daniel Glöckner <daniel-gl@gmx.net>
Cc: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2014-10-14 02:18:19 +02:00
Maciej W. Rozycki
31632dbdba drivers/rtc/rtc-cmos.c: drivers/char/rtc.c features for DECstation support
This brings in drivers/char/rtc.c functionality required for DECstation
and, should the maintainers decide to switch, Alpha systems to use
rtc-cmos.

Specifically these features are made available:

* RTC iomem rather than x86/PCI port I/O mapping, controlled with the
  RTC_IOMAPPED macro as with the original driver.  The DS1287A chip in all
  DECstation systems is mapped in the host bus address space as a
  contiguous block of 64 32-bit words of which the least significant byte
  accesses the RTC chip for both reads and writes.  All the address and
  data window register accesses are made transparently by the chipset glue
  logic so that the device appears directly mapped on the host bus.

* A way to set the size of the address space explicitly with the
  newly-added `address_space' member of the platform part of the RTC
  device structure.  This avoids the unreliable heuristics that does not
  work in a setup where the RTC is not explicitly accessed with the usual
  address and data window register pair.

* The ability to use the RTC periodic interrupt as a system clock
  device, which is implemented by arch/mips/kernel/cevt-ds1287.c for
  DECstation systems and takes the RTC interrupt away from the RTC driver.
   Eventually hooking back to the clock device's interrupt handler should
  be possible for the purpose of the alarm clock and possibly also
  update-in-progress interrupt, but this is not done by this change.

  o To avoid interfering with the clock interrupt all the places where
    the RTC interrupt mask is fiddled with are only executed if and IRQ
    has been assigned to the RTC driver.

  o To avoid changing the clock setup Register A is not fiddled with
    if CMOS_RTC_FLAGS_NOFREQ is set in the newly-added `flags' member of
    the platform part of the RTC device structure.  Originally, in
    drivers/char/rtc.c, this was keyed with the absence of the RTC
    interrupt, just like the interrupt mask, but there only the periodic
    interrupt frequency is set, whereas rtc-cmos also sets the divider
    bits.  Therefore a new flag is introduced so that systems where the
    RTC interrupt is not usable rather than used as a system clock device
    can fully initialise the RTC.

* A small clean-up is made to the IRQ assignment code that makes the IRQ
  number hardcoded to -1 rather than arbitrary -ENXIO (or whatever error
  happens to be returned by platform_get_irq) where no IRQ has been
  assigned to the RTC driver (NO_IRQ might be another candidate, but it
  looks like this macro has inconsistent or missing definitions and
  limited use and might therefore be unsafe).

Verified to work correctly with a DECstation 5000/240 system.

[akpm@linux-foundation.org: fix weird code layout]
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2014-06-06 16:08:07 -07:00
Mika Westerberg
b5ada4600d drivers/rtc/rtc-cmos.c: fix compilation warning when !CONFIG_PM_SLEEP
CONFIG_PM will be set also if only CONFIG_PM_RUNTIME is set which causes
the compiler to emit following warning:

  drivers/rtc/rtc-cmos.c:845:12: warning: =E2=80=98cmos_resume=E2=80=99 defined but not used [-Wunused-function]

Fix this by using CONFIG_PM_SLEEP instead of CONFIG_PM and removing it
from the driver pm ops as this has been taken care by
SIMPLE_DEV_PM_OPS() already.

Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2014-04-03 16:21:21 -07:00
Andrew Morton
24b34472e2 drivers/rtc/rtc-cmos.c: propagate hpet_register_irq_handler() failure
If hpet_register_irq_handler() fails, cmos_do_probe() will incorrectly
return 0.

Reported-by: Julia Lawall <julia.lawall@lip6.fr>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Rob Herring <robh+dt@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2014-01-23 16:37:00 -08:00
Geert Uytterhoeven
c823a20244 drivers/rtc/rtc-cmos.c: remove superfluous name cast
device_driver.name is "const char *"

Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2014-01-23 16:36:59 -08:00
Borislav Petkov
d5a1c7e3fc rtc-cmos: Add an alarm disable quirk
41c7f74242 ("rtc: Disable the alarm in the hardware (v2)") added the
functionality to disable the RTC wake alarm when shutting down the box.

However, there are at least two b0rked BIOSes we know about:

https://bugzilla.novell.com/show_bug.cgi?id=812592
https://bugzilla.novell.com/show_bug.cgi?id=805740

where, when wakeup alarm is enabled in the BIOS, the machine reboots
automatically right after shutdown, regardless of what wakeup time is
programmed.

Bisecting the issue lead to this patch so disable its functionality with
a DMI quirk only for those boxes.

Cc: Brecht Machiels <brecht@mos6581.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Rabin Vincent <rabin.vincent@stericsson.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Borislav Petkov <bp@suse.de>
[jstultz: Changed variable name for clarity, added extra dmi entry]
Tested-by: Brecht Machiels <brecht@mos6581.org>
Tested-by: Borislav Petkov <bp@suse.de>
Signed-off-by: John Stultz <john.stultz@linaro.org>
2013-12-23 12:52:20 -08:00
Jingoo Han
97a92e77ca drivers/rtc/rtc-cmos.c: use dev_get_platdata()
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly.  This is a cosmetic change to make
the code simpler and enhance the readability.

Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2013-11-13 12:09:28 +09:00
Sachin Kamat
d7d954acb7 drivers/rtc/rtc-cmos.c: remove redundant dev_set_drvdata
Driver core sets the driver data to NULL upon device_release or on probe
failure.

Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Cc: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2013-11-13 12:09:27 +09:00
Shuah Khan
a8a3808b43 rtc: convert rtc-cmos to dev_pm_ops from legacy pm_ops
Convert drivers/rtc/rtc-cmos to use dev_pm_ops instead of legacy pm_ops.
This patch depends on pnp driver bus ops change to invoke pnp_driver
dev_pm_ops.

Signed-off-by: Shuah Khan <shuah.kh@samsung.com>
Cc: Matthew Garrett <matthew.garrett@nebula.com>
Cc: Leonidas Da Silva Barbosa <leosilva@linux.vnet.ibm.com>
Cc: Ashley Lai <ashley@ashleylai.com>
Cc: Rajiv Andrade <mail@srajiv.net>
Cc: Marcel Selhorst <tpmdd@selhorst.net>
Cc: Sirrix AG <tpmdd@sirrix.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: "Rafael J. Wysocki" <rafael.j.wysocki@intel.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Peter Hüwe <PeterHuewe@gmx.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2013-09-11 15:58:15 -07:00
Derek Basehore
998a06051a drivers/rtc/rtc-cmos.c: work around bios clearing rtc control
The bios may clear the rtc control register when resuming the system. Since the
cmos interrupt handler may now be run before the rtc_cmos is resumed, this can
cause the interrupt handler to ignore an alarm since the alarm bit is not set in
the rtc control register. To work around this, check if the rtc_cmos is
suspended and use the stored value for the rtc control register.

Signed-off-by: Derek Basehore <dbasehore@chromium.org>
Reviewed-by: Sameer Nanda <snanda@chromium.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Jingoo Han <jg1.han@samsung.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: John Stultz <john.stultz@linaro.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2013-07-03 16:08:00 -07:00
Sachin Kamat
5e8599d21b drivers/rtc/rtc-cmos.c: fix whitespace related errors
Fixes the following types of issues:

  ERROR: space required after that ',' (ctx:VxV)
  WARNING: please, no spaces at the start of a line

Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Cc: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2013-07-03 16:07:46 -07:00
Derek Basehore
ebf8d6c863 drivers/rtc/rtc-cmos.c: fix accidentally enabling rtc channel
During resume, we call hpet_rtc_timer_init after masking an irq bit in
hpet.  This will cause the call to hpet_disable_rtc_channel to be undone
if RTC_AIE is the only bit not masked.

Allowing the cmos interrupt handler to run before resuming caused some
issues where the timer for the alarm was not removed.  This would cause
other, later timers to not be cleared, so utilities such as hwclock
would time out when waiting for the update interrupt.

[akpm@linux-foundation.org: coding-style tweak]
Signed-off-by: Derek Basehore <dbasehore@chromium.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2013-06-12 16:29:45 -07:00
Derek Basehore
e005715efa drivers/rtc/rtc-cmos.c: don't disable hpet emulation on suspend
There's a bug where rtc alarms are ignored after the rtc cmos suspends
but before the system finishes suspend.  Since hpet emulation is
disabled and it still handles the interrupts, a wake event is never
registered which is done from the rtc layer.

This patch reverts commit d1b2efa83f ("rtc: disable hpet emulation on
suspend") which disabled hpet emulation.  To fix the problem mentioned
in that commit, hpet_rtc_timer_init() is called directly on resume.

Signed-off-by: Derek Basehore <dbasehore@chromium.org>
Cc: Maxim Levitsky <maximlevitsky@gmail.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2013-04-29 18:28:35 -07:00
Jingoo Han
ee4433573b rtc: rtc-cmos: use dev_warn()/dev_dbg() instead of printk()/pr_debug()
Fix the checkpatch warning as below:

  WARNING: Prefer netdev_err(netdev, ... then dev_err(dev, ... then pr_err(...  to printk(KERN_ERR ...

Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2013-02-21 17:22:29 -08:00
Sachin Kamat
c8a6046e1e drivers/rtc: use of_match_ptr() macro
This eliminates having an #ifdef returning NULL for the case when OF is
disabled.  Maintains consistency in cases where OF is always selected.

Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2013-02-21 17:22:27 -08:00
Greg Kroah-Hartman
5a167f4543 Drivers: rtc: remove __dev* attributes.
CONFIG_HOTPLUG is going away as an option.  As a result, the __dev*
markings need to be removed.

This change removes the use of __devinit, __devexit_p, __devinitdata,
__devinitconst, and __devexit from these drivers.

Based on patches originally written by Bill Pemberton, but redone by me
in order to handle some of the coding style issues better, by hand.

Cc: Bill Pemberton <wfp5p@virginia.edu>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Mike Frysinger <vapier.adi@gmail.com>
Cc: Wan ZongShun <mcuos.com@gmail.com>
Cc: Guan Xuetao <gxt@mprc.pku.edu.cn>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-01-03 15:57:02 -08:00
NeilBrown
7523ceed42 RTC: Avoid races between RTC alarm wakeup and suspend.
If an RTC alarm fires just as suspend is happening, it is possible for
suspend to complete and the alarm to be missed.

To avoid the race, we must register the event with the PM core.

As the event is made visible to userspace through a thread which is
only scheduled by the interrupt, we need a pm_stay_awake/pm_relax
pair preventing suspend from the interrupt until the thread completes
its work.

This makes the pm_wakeup_event() call in cmos_interrupt unnecessary as
it provides suspend protection for all RTCs that use rtc_update_irq.

Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
2012-08-08 20:49:16 +02:00
Paul Fox
b45bae36b8 rtc-cmos: report wakeups from interrupt handler
When suspending the system with an important RTC wake alarm active,
it is possible that the RTC alarm will expire before the system has
gone to sleep (e.g. short alarm timer, or an unusually long suspend
routine).

If this happens, the RTC alarm should trigger a wakeup event, possibly
aborting system suspend. This condition can be detected in the form
of an RTC alarm interrupt.

Signed-off-by: Paul Fox <pgf@laptop.org>
Signed-off-by: Daniel Drake <dsd@laptop.org>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
2012-07-17 22:14:48 +02:00
Daniel Drake
b2201e5482 rtc-cmos / PM: report wakeup event on ACPI RTC alarm
When the ACPI-driven RTC alarm wakes the system, report it as a wakeup
event. This allows userspace to determine that the reason for system
wakeup was RTC alarm.

Signed-off-by: Daniel Drake <dsd@laptop.org>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
2012-05-29 21:20:23 +02:00
Yong Zhang
2f6e5f9458 drivers/rtc: remove IRQF_DISABLED
Since commit e58aa3d2d0 ("genirq: run irq handlers with interrupts
disabled") we run all interrupt handlers with interrupts disabled and we
even check and yell when an interrupt handler returns with interrupts
enabled - see commit b738a50a20 ("genirq: warn when handler enables
interrupts").

So now this flag is a NOOP and can be removed.

Signed-off-by: Yong Zhang <yong.zhang0@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Wan ZongShun <mcuos.com@gmail.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2012-03-23 16:58:39 -07:00
Ondrej Zary
b43c1ea4d6 drivers/rtc/rtc-cmos.c: fix broken NVRAM bank 2 writing
Fix writing to NVRAM bank 2 in rtc-cmos driver.  It never worked since its
introduction in 2.6.28 because of a typo.

Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2012-01-10 16:30:52 -08:00
Joe Perches
28f65c11f2 treewide: Convert uses of struct resource to resource_size(ptr)
Several fixes as well where the +1 was missing.

Done via coccinelle scripts like:

@@
struct resource *ptr;
@@

- ptr->end - ptr->start + 1
+ resource_size(ptr)

and some grep and typing.

Mostly uncompiled, no cross-compilers.

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2011-06-10 14:55:36 +02:00
Linus Torvalds
d10902812c Merge branch 'x86-platform-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'x86-platform-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (27 commits)
  x86: Clean up apic.c and apic.h
  x86: Remove superflous goal definition of tsc_sync
  x86: dt: Correct local apic documentation in device tree bindings
  x86: dt: Cleanup local apic setup
  x86: dt: Fix OLPC=y/INTEL_CE=n build
  rtc: cmos: Add OF bindings
  x86: ce4100: Use OF to setup devices
  x86: ioapic: Add OF bindings for IO_APIC
  x86: dtb: Add generic bus probe
  x86: dtb: Add support for PCI devices backed by dtb nodes
  x86: dtb: Add device tree support for HPET
  x86: dtb: Add early parsing of IO_APIC
  x86: dtb: Add irq domain abstraction
  x86: dtb: Add a device tree for CE4100
  x86: Add device tree support
  x86: e820: Remove conditional early mapping in parse_e820_ext
  x86: OLPC: Make OLPC=n build again
  x86: OLPC: Remove extra OLPC_OPENFIRMWARE_DT indirection
  x86: OLPC: Cleanup config maze completely
  x86: OLPC: Hide OLPC_OPENFIRMWARE config switch
  ...

Fix up conflicts in arch/x86/platform/ce4100/ce4100.c
2011-03-15 20:01:36 -07:00
John Stultz
51ba60c5bb RTC: Cleanup rtc_class_ops->update_irq_enable()
Now that the generic code handles UIE mode irqs via periodic
alarm interrupts, no one calls the
rtc_class_ops->update_irq_enable() method anymore.

This patch removes the driver hooks and implementations of
update_irq_enable if no one else is calling it.

CC: Thomas Gleixner <tglx@linutronix.de>
CC: Alessandro Zummo <a.zummo@towertech.it>
CC: Marcelo Roberto Jimenez <mroberto@cpti.cetuc.puc-rio.br>
CC: rtc-linux@googlegroups.com
Signed-off-by: John Stultz <john.stultz@linaro.org>
2011-03-09 11:23:37 -08:00
John Stultz
696160fec1 RTC: Cleanup rtc_class_ops->irq_set_freq()
With the generic rtc code now emulating PIE mode irqs via an
hrtimer, no one calls the rtc_class_ops->irq_set_freq call.

This patch removes the hook and deletes the driver functions
if no one else calls them.

CC: Thomas Gleixner <tglx@linutronix.de>
CC: Alessandro Zummo <a.zummo@towertech.it>
CC: Marcelo Roberto Jimenez <mroberto@cpti.cetuc.puc-rio.br>
CC: rtc-linux@googlegroups.com
Signed-off-by: John Stultz <john.stultz@linaro.org>
2011-03-09 11:23:35 -08:00
John Stultz
80d4bb515b RTC: Cleanup rtc_class_ops->irq_set_state
With PIE mode interrupts now emulated in generic code via an hrtimer,
no one calls rtc_class_ops->irq_set_state(), so this patch removes it
along with driver implementations.

CC: Thomas Gleixner <tglx@linutronix.de>
CC: Alessandro Zummo <a.zummo@towertech.it>
CC: Marcelo Roberto Jimenez <mroberto@cpti.cetuc.puc-rio.br>
CC: rtc-linux@googlegroups.com
Signed-off-by: John Stultz <john.stultz@linaro.org>
2011-03-09 11:23:34 -08:00
Sebastian Andrzej Siewior
3bcbaf6e08 rtc: cmos: Add OF bindings
This allows to load the OF driver based informations from the device
tree. Systems without BIOS may need to perform some initialization.
PowerPC creates a PNP device from the OF information and performs this
kind of initialization in their private PCI quirk. This looks more
generic.

This patch also avoids registering the platform RTC driver on X86 if
we have a device tree blob. Otherwise we would setup the device based
on the hardcoded information in arch/x86 rather than the device tree
based one.

[ tglx: Changed "int of_have_populated_dt()" to bool as recommended by
        Grant ]

Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Dirk Brandewie <dirk.brandewie@gmail.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Cc: sodaville@linutronix.de
Cc: devicetree-discuss@lists.ozlabs.org
Cc: rtc-linux@googlegroups.com
Cc: Alessandro Zummo <a.zummo@towertech.it>
LKML-Reference: <1298405266-1624-12-git-send-email-bigeasy@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2011-02-23 22:27:55 +01:00
Paul Fox
2fb08e6ca9 rtc-cmos: fix suspend/resume
rtc-cmos was setting suspend/resume hooks at the device_driver level.
However, the platform bus code (drivers/base/platform.c) only looks for
resume hooks at the dev_pm_ops level, or within the platform_driver.

Switch rtc_cmos to use dev_pm_ops so that suspend/resume code is executed
again.

Paul said:

: The user visible symptom in our (XO laptop) case was that rtcwake would
: fail to wake the laptop.  The RTC alarm would expire, but the wakeup
: wasn't unmasked.
:
: As for severity, the impact may have been reduced because if I recall
: correctly, the bug only affected platforms with CONFIG_PNP disabled.

Signed-off-by: Paul Fox <pgf@laptop.org>
Signed-off-by: Daniel Drake <dsd@laptop.org>
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Cc: <stable@kernel.org>		[2.6.37.x]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2011-01-13 08:03:12 -08:00
Srikanth Krishnakar
8cb7c71bda rtc-cmos.c : Fix warning on PowerPC
The following warning is seen while compilation of PowerPC kernel:

 CC      drivers/rtc/rtc-cmos.o
drivers/rtc/rtc-cmos.c:697:2: warning: #warning Assuming 128 bytes
of RTC+NVRAM address space, not 64 bytes.

Fix it by adding defined(__powerpc__).

Signed-off-by: Srikanth Krishnakar <skrishna@mvista.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2010-11-29 15:48:19 +11:00
Christian Dietrich
de639c3116 drivers/rtc: remove unneeded ifdef CONFIG_PM
Because CONFIG_PM is a precondition to CONFIG_ACPI, the ifdef CONFIG_PM
within ifdef CONFIG_ACPI is redundant.

Signed-off-by: Christian Dietrich <qy03fugy@stud.informatik.uni-erlangen.de>
Acked-by: Wan ZongShun <mcuos.com@gmail.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2010-08-11 08:59:08 -07:00
Dan Carpenter
6ba8bcd457 rtc-cmos: do dev_set_drvdata() earlier in the initialization
The bug is an oops when dev_get_drvdata() returned null in
cmos_update_irq_enable().  The call tree looks like this:
  rtc_dev_ioctl()
    => rtc_update_irq_enable()
      => cmos_update_irq_enable()

It's caused by a race condition in the module initialization.  It is
rtc_device_register() which makes the ioctl operations live so I moved
the call to dev_set_drvdata() before the call to rtc_device_register().

Addresses https://bugzilla.kernel.org/show_bug.cgi?id=15963

Reported-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Dan Carpenter <error27@gmail.com>
Tested-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Paul Gortmaker <p_gortmaker@yahoo.com>
Cc: Malte Schroder <maltesch@gmx.de>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Herton Ronaldo Krzesinski <herton@mandriva.com.br>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2010-05-25 08:07:08 -07:00
Arnaud Patard
3804a89bfb RTC: rtc-cmos: Fix binary mode support
As a follow-up to the thread about RTC support for some Loongson 2E/2F
boards, this patch tries to address the "REVISIT"/"FIXME" comments about
rtc binary mode handling and allow rtc to work with rtc in binary mode.
I've also raised the message about 24-h mode not supported to warning
otherwise, one may end up with no rtc without any message in the kernel
log.

Signed-off-by: Arnaud Patard <apatard@mandriva.com>
To: linux-mips@linux-mips.org
To: rtc-linux@googlegroups.com
Cc: david-b@pacbell.net
Cc: a.zummo@towertech.it
Cc: akpm@linux-foundation.org
Patchwork: http://patchwork.linux-mips.org/patch/1158/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2010-05-21 21:31:19 +01:00
Chris Wright
2c3c8bea60 sysfs: add struct file* to bin_attr callbacks
This allows bin_attr->read,write,mmap callbacks to check file specific data
(such as inode owner) as part of any privilege validation.

Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-05-21 09:37:31 -07:00
OGAWA Hirofumi
004731b2c7 rtc_cmos: convert shutdown to new pnp_driver->shutdown
commit abd6633c67 ("pnp: add a shutdown
method to pnp drivers") adds shutdown method to bus driver blindly.  With
it, driver->shutdown is no longer valid.

Use pnp_driver->shutdown instead.

Addresses http://bugzilla.kernel.org/show_bug.cgi?id=14889

Signed-off-by: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp>
Reported-by: Malte Schröder <maltesch@gmx.de>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: David Hardeman <david@hardeman.nu>
Cc: Dmitry Torokhov <dtor@mail.ru>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Paul Gortmaker <p_gortmaker@yahoo.com>
Cc: <stable@kernel.org>		[2.6.32.x]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2010-01-11 09:34:07 -08:00
Wu Zhangjin
95abd0dfaf RTC: rtc-cmos.c: Fix warning on MIPS
This patch fixes the following warning with RTC_LIB on MIPS:

drivers/rtc/rtc-cmos.c:697:2: warning: #warning Assuming 128 bytes of
RTC+NVRAM address space, not 64 bytes.

Signed-off-by: Wu Zhangjin <wuzhangjin@gmail.com>
Cc: Arnaud Patard <apatard@mandriva.com>
Cc: linux-mips@linux-mips.org
Cc: rtc-linux@googlegroups.com
Cc: Paul Gortmaker <p_gortmaker@yahoo.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Patchwork: http://patchwork.linux-mips.org/patch/570/
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2009-12-17 01:57:37 +00:00
Herton Ronaldo Krzesinski
a8462ef63c rtc-cmos: convert RTC_AIE/RTC_UIE to rtc irq API
Drop ioctl function that handles RTC_AIE/RTC_UIE, and use instead the
rtc subsystem API (alarm_irq_enable/update_irq_enable callbacks).

Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com.br>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-12-16 07:19:58 -08:00
Maxim Levitsky
d1b2efa83f rtc: disable hpet emulation on suspend
I noticed that rtc wont generate interrupts after a resume from disk.
Here hpet rtc emulation is used.

Problem is that rtc hpet comparator, isn't reinitialized after resume.
Easiest way to solve this, is always mask all hpet interrupts on suspend
This is triggered, when suspending with alarm set.

Otherwise, hpet driver will think it doesn't need to reinitialize
the rtc comparator, thus rtc interrupts won't work.

This emulation isn't need for wakealarm.

Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Cc: David Brownell <david-b@pacbell.net>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-12-16 07:19:58 -08:00
Thadeu Lima de Souza Cascardo
659098141d rtc: mark if rtc-cmos drivers were successfully registered
rtc-cmos has two drivers, one PNP and one platform.  When PNP has not
succeeded probing, platform is registered.  However, it tries to
unregister both drivers unconditionally, instead of only unregistering
those that were successfully registered.  This causes runtime warnings to
be emitted from the driver core code.

Fix this with a boolean variable for each driver indicating whether
registering was successful.

Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@holoscopio.com>
Cc: David Brownell <david-b@pacbell.net>
Cc: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Alessandro Zummo <alessandro.zummo@towertech.it>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: David Brownell <david-b@pacbell.net>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Cc: Greg KH <greg@kroah.com>
Cc: Ozan Caglayan <ozan@pardus.org.tr>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-07-29 19:10:35 -07:00
Krzysztof Halasa
6d029b6451 rtc-cmos: fix printk output
With no IRQ available/defined, RTC-CMOS driver prints something like:
	rtc0: alarms up to one no, y3k, 114 bytes nvram
                              ^^^^
I guess the following is a bit easier to understand:
	rtc0: no alarms, y3k, 114 bytes nvram

Signed-off-by: Krzysztof Halasa <khc@pm.waw.pl>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-04-21 13:41:50 -07:00
Jonathan Cameron
5d2a50371d rtc: move power of 2 periodic frequency check down into drivers
Move the power of 2 check on frequencies down into individual rtc drivers

This is to allow for non power of 2 real time clock periodic interrupts
such as those on the pxa27x to be found in the new pxa27x-rtc driver

Signed-off-by: Jonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: Alessandro Zummo <a.zummo@towertech.it>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-01-06 15:59:24 -08:00
Anton Vorontsov
2fac6674dd rtc: bunch of drivers: fix 'no irq' case handing
This patch fixes a bunch of irq checking misuses.  Most drivers were
getting irq via platform_get_irq(), which returns -ENXIO or r->start.

rtc-cmos.c is special.  It is using PNP and platform bindings.  Hopefully
nobody is using PNP IRQ 0 for RTC.  So the changes should be safe.

rtc-sh.c is using platform_get_irq, but was storing a result into an
unsigned type, then was checking for < 0.  This is fixed now.

Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-01-06 15:59:23 -08:00
Kay Sievers
d4afc76c0b rtc: struct device: replace bus_id with dev_name(), dev_set_name()
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Acked-By: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-01-06 15:59:23 -08:00
Frans Pop
80bb26d406 rtc-cmos: fix boot log message
-rtc0: alarms up to one month, y3k, 114 bytes nvram, , hpet irqs irqs
+rtc0: alarms up to one month, y3k, 114 bytes nvram, hpet irqs

Signed-off-by: Frans Pop <elendil@planet.nl>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-11-06 15:41:19 -08:00
Parag Warudkar
01e8ef11bc x86: sysfs: kill owner field from attribute
Tejun's commit 7b595756ec made sysfs
attribute->owner unnecessary.  But the field was left in the structure to
ease the merge.  It's been over a year since that change and it is now
time to start killing attribute->owner along with its users - one arch at
a time!

This patch is attempt #1 to get rid of attribute->owner only for
CONFIG_X86_64 or CONFIG_X86_32 .  We will deal with other arches later on
as and when possible - avr32 will be the next since that is something I
can test.  Compile (make allyesconfig / make allmodconfig / custom config)
and boot tested.

akpm: the idea is that we put the declaration of sttribute.owner inside
`#ifndef CONFIG_X86'.  But that proved to be too ambitious for now because
new usages kept on turning up in subsystem trees.

[akpm: remove the ifdef for now]
Signed-off-by: Parag Warudkar <parag.lkml@gmail.com>
Cc: Greg KH <greg@kroah.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Tejun Heo <htejun@gmail.com>
Cc: Len Brown <lenb@kernel.org>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Roland Dreier <rolandd@cisco.com>
Cc: David Brownell <david-b@pacbell.net>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-20 08:52:42 -07:00
Adrian Bunk
fe20ba70ab drivers/rtc/: use bcd2bin/bin2bcd
Change drivers/rtc/ to use the new bcd2bin/bin2bcd functions instead of
the obsolete BCD_TO_BIN/BIN_TO_BCD/BCD2BIN/BIN2BCD macros.

Signed-off-by: Adrian Bunk <bunk@kernel.org>
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-20 08:52:41 -07:00