Move mt76x02_get_txpower utility routine in mt76x02-lib module
in order to be reused by mt76x0 and mt76x2u drivers
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move mt76x02_sw_scan and mt76x02_sw_scan_complete utility routines
in mt76x02_util.c in order to be reused by mt76x0 and mt76x2u drivers
and remove duplicated code
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Enable/disable pre_tbtt_tasklet in mt76x0 driver in order
to add AP support
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move mt76x02_tx beacon utility routines in mt76x02_mmio.c
in order to be reused by mt76x0 driver adding AP support
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move mt76x02_beacon mac routines in mt76x02_mac.c in
order to be reused by mt76x0 driver adding AP support
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move mt76x02_init_device routine in mt76x02_util.c in order to be
reused by mt76x0 driver and remove duplicated code. Move interface
combo definition supported by the driver in mt76x02_init_device routine
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move mt76x02_mac_set_short_preamble routine in mt76x02-lib module
since it is shared between mt76x0 and mt76x2 drivers
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Unify firmware version used on mt76x0e and mt76x0u drivers.
Fallback to mt7610u fw if mt7610e one is not available
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Remove no longer used mt76x0_mac_set_ampdu_factor routine
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Add missing firmware declaration for mt76x0e driver
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Simplify mt76x0_init_mac_registers routine using mt76_set, mt76_clear
and mt76_rmw utility routines
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Update mt76x0_phy_ant_select() to conform vendor driver, most notably
add dual antenna mode support, read configuration from EEPROM and
move ant select out of channel config to init phase. Plus small MT7630E
quirk for MT_CMB_CTRL register which vendor driver dedicated to this
chip do.
This make MT7630E workable with mt76x0e driver and do not cause any
problems on MT7610U for me.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Add submit_urb and rx_urb static tracepoints in mt76-usb module.
Move trace_mac_txstat_fetch in mt76x02_mac_load_tx_status routine
in order to be available to usb drivers. Moreover remove
no longer used mt76x0/trace.{c,h}
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Some RF registers need different values for various chips.
For at least mt76x0_rf_central_tab registers, overwriting them later does
not work, as the wrong values can cause the entire system to hang on some
devices with MT7610E
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Make previously exported functions static where possible
Acked-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Driver works better for MT7630 without MCU calibration, which
looks like it can hangs the firmware. Vendor driver do not
perform it for MT7630 as well.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Align phy calibration logic between mt76x0u and mt76x0e drivers
This patch improves connection stability with low SNR
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Add mac workqueue support to mt76x2u driver in order
to compute device statistics and add mac stuck routine
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Use mt76x02_mac_work utility routine as stats workqueue handler
and remove duplicated code. Moreover run mac stuck check in
mt76x02_mac_work for client interfaces.
Remove no longer used avg_ampdu_len and mt76x02_mac_stats data
structure in mt76x02_dev
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Use mt76x02 debugfs implementation and remove duplicated code
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move mt76x02_debugfs in mt76x02-lib module in order to
be reused by mt76x0 driver and remove duplicated code
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move mt76x02_mac_work routine in mt76x02_mac.c in order to be reused by
mt76x0 driver to read device statistics
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move mt76x02_update_channel routine in mt76x02-lib module in
order to be reused by mt76x0 driver adding get_survey support
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Improve initvals_phy.h code readability (there are no actual changes
of original values)
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Simplify mt76x0_phy_vco_cal and mt76x0_phy_set_chan_rf_params
routines using mt76x0_rf_wr, mt76x0_rf_set and mt76x0_rf_clear
helper routines. Moreover over get rid of magic numbers
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Use mt76x0_phy as prefix for routines in mt76x0/phy.c
Moreover use mt76x0_rf_set to enable vco calibration in
mt76x0_phy_vco_cal
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Update vga tuning algorithm to the one used in mt76x2 driver
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Unify firmware version used on mt76x2e and mt76x2u drivers
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Daniel Borkmann says:
====================
bpf-next 2018-11-30
The following pull-request contains BPF updates for your *net-next* tree.
(Getting out bit earlier this time to pull in a dependency from bpf.)
The main changes are:
1) Add libbpf ABI versioning and document API naming conventions
as well as ABI versioning process, from Andrey.
2) Add a new sk_msg_pop_data() helper for sk_msg based BPF
programs that is used in conjunction with sk_msg_push_data()
for adding / removing meta data to the msg data, from John.
3) Optimize convert_bpf_ld_abs() for 0 offset and fix various
lib and testsuite build failures on 32 bit, from David.
4) Make BPF prog dump for !JIT identical to how we dump subprogs
when JIT is in use, from Yonghong.
5) Rename btf_get_from_id() to make it more conform with libbpf
API naming conventions, from Martin.
6) Add a missing BPF kselftest config item, from Naresh.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
During porting libbpf to bcc, I got some warnings like below:
...
[ 2%] Building C object src/cc/CMakeFiles/bpf-shared.dir/libbpf/src/libbpf.c.o
/home/yhs/work/bcc2/src/cc/libbpf/src/libbpf.c:12:0:
warning: "_GNU_SOURCE" redefined [enabled by default]
#define _GNU_SOURCE
...
[ 3%] Building C object src/cc/CMakeFiles/bpf-shared.dir/libbpf/src/libbpf_errno.c.o
/home/yhs/work/bcc2/src/cc/libbpf/src/libbpf_errno.c: In function ‘libbpf_strerror’:
/home/yhs/work/bcc2/src/cc/libbpf/src/libbpf_errno.c:45:7:
warning: assignment makes integer from pointer without a cast [enabled by default]
ret = strerror_r(err, buf, size);
...
bcc is built with _GNU_SOURCE defined and this caused the above warning.
This patch intends to make libpf _GNU_SOURCE friendly by
. define _GNU_SOURCE in libbpf.c unless it is not defined
. undefine _GNU_SOURCE as non-gnu version of strerror_r is expected.
Signed-off-by: Yonghong Song <yhs@fb.com>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
We can remove the loop and conditional branches
and compute wscale efficiently thanks to ilog2()
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
skb_linearization can fail due to memory allocation failure.
In such a case, the driver will drop the packet. In such a case
The driver used to print an error message.
This patch replaces this error message by a dedicated statistic.
Signed-off-by: Michael Shteinbok <michael.shteinbok@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add comments in the switch statement for XDP action to indicate
fallthrough is intended.
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Kunihiko Hayashi says:
====================
Add suspend/resume support for AVE ethernet driver
This series adds support for suspend/resume to AVE ethernet driver.
And to avoid the error that wol state of phy hardware is enabled by default,
this sets initial wol state to disabled and add preservation the state in
suspend/resume sequence.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the wol state forces to be initialized after reset, the state should
be preserved in suspend/resume sequence.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If wol state of phy hardware is enabled after reset, phy_ethtool_get_wol()
returns that wol.wolopts is true.
However, since net_device.wol_enabled is zero and this doesn't apply wol
state until calling ethtool_set_wol(), so mdio_bus_phy_may_suspend()
returns true, that is, it's in a state where phy can suspend even though
wol state is enabled.
In this inconsistency, phy_suspend() returns -EBUSY, and at last,
suspend sequence fails with the following message:
dpm_run_callback(): mdio_bus_phy_suspend+0x0/0x58 returns -16
PM: Device 65000000.ethernet-ffffffff:01 failed to suspend: error -16
PM: Some devices failed to suspend, or early wake event detected
In order to fix the above issue, this patch forces to set initial wol state
to disabled as default.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch introduces suspend and resume functions to ave driver.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I ended up tracking down some rather nasty issues with f2fs (and other
filesystem modules) constantly crashing on my kernel down to a
combination of out of bounds memory accesses, one of which was coming
from brcmfmac during module load:
[ 30.891382] brcmfmac: brcmf_fw_alloc_request: using brcm/brcmfmac4356-sdio for chip BCM4356/2
[ 30.894437] ==================================================================
[ 30.901581] BUG: KASAN: global-out-of-bounds in brcmf_fw_alloc_request+0x42c/0x480 [brcmfmac]
[ 30.909935] Read of size 1 at addr ffff2000024865df by task kworker/6:2/387
[ 30.916805]
[ 30.918261] CPU: 6 PID: 387 Comm: kworker/6:2 Tainted: G O 4.20.0-rc3Lyude-Test+ #19
[ 30.927251] Hardware name: amlogic khadas-vim2/khadas-vim2, BIOS 2018.07-rc2-armbian 09/11/2018
[ 30.935964] Workqueue: events brcmf_driver_register [brcmfmac]
[ 30.941641] Call trace:
[ 30.944058] dump_backtrace+0x0/0x3e8
[ 30.947676] show_stack+0x14/0x20
[ 30.950968] dump_stack+0x130/0x1c4
[ 30.954406] print_address_description+0x60/0x25c
[ 30.959066] kasan_report+0x1b4/0x368
[ 30.962683] __asan_report_load1_noabort+0x18/0x20
[ 30.967547] brcmf_fw_alloc_request+0x42c/0x480 [brcmfmac]
[ 30.967639] brcmf_sdio_probe+0x163c/0x2050 [brcmfmac]
[ 30.978035] brcmf_ops_sdio_probe+0x598/0xa08 [brcmfmac]
[ 30.983254] sdio_bus_probe+0x190/0x398
[ 30.983270] really_probe+0x2a0/0xa70
[ 30.983296] driver_probe_device+0x1b4/0x2d8
[ 30.994901] __driver_attach+0x200/0x280
[ 30.994914] bus_for_each_dev+0x10c/0x1a8
[ 30.994925] driver_attach+0x38/0x50
[ 30.994935] bus_add_driver+0x330/0x608
[ 30.994953] driver_register+0x140/0x388
[ 31.013965] sdio_register_driver+0x74/0xa0
[ 31.014076] brcmf_sdio_register+0x14/0x60 [brcmfmac]
[ 31.023177] brcmf_driver_register+0xc/0x18 [brcmfmac]
[ 31.023209] process_one_work+0x654/0x1080
[ 31.032266] worker_thread+0x4f0/0x1308
[ 31.032286] kthread+0x2a8/0x320
[ 31.039254] ret_from_fork+0x10/0x1c
[ 31.039269]
[ 31.044226] The buggy address belongs to the variable:
[ 31.044351] brcmf_firmware_path+0x11f/0xfffffffffffd3b40 [brcmfmac]
[ 31.055601]
[ 31.057031] Memory state around the buggy address:
[ 31.061800] ffff200002486480: 04 fa fa fa fa fa fa fa 00 00 00 00 00 00 00 00
[ 31.068983] ffff200002486500: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 31.068993] >ffff200002486580: 00 00 00 00 00 00 00 00 fa fa fa fa 00 00 00 00
[ 31.068999] ^
[ 31.069017] ffff200002486600: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 31.096521] ffff200002486680: 00 00 00 00 00 00 00 00 00 00 00 00 fa fa fa fa
[ 31.096528] ==================================================================
[ 31.096533] Disabling lock debugging due to kernel taint
It appears that when trying to determine the length of the string in the
alternate firmware path, we make the mistake of not handling the case
where the firmware path is empty correctly. Since strlen(mp_path) can
return 0, we'll end up accessing mp_path[-1] when the firmware_path
isn't provided through the module arguments.
So, fix this by just setting the end char to '\0' by default, and only
changing it if we have a non-zero length. Additionally, use strnlen()
with BRCMF_FW_ALTPATH_LEN instead of strlen() just to be extra safe.
Fixes: 2baa3aaee2 ("brcmfmac: introduce brcmf_fw_alloc_request() function")
Cc: Hante Meuleman <hante.meuleman@broadcom.com>
Cc: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Cc: Franky Lin <franky.lin@broadcom.com>
Cc: Arend van Spriel <arend.vanspriel@broadcom.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: Arend Van Spriel <arend.vanspriel@broadcom.com>
Cc: Himanshu Jha <himanshujha199640@gmail.com>
Cc: Dan Haab <dhaab@luxul.com>
Cc: Jia-Shyr Chuang <saint.chuang@cypress.com>
Cc: Ian Molton <ian@mnementh.co.uk>
Cc: <stable@vger.kernel.org> # v4.17+
Signed-off-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
ARM systems with UEFI may have both devicetree (of) and DMI data in this
case we end up setting brcmf_mp_device.board_type twice.
In this case we should prefer the devicetree data, because:
1) The devicerree data is more reliable
2) Some ARM systems (e.g. the Raspberry Pi 3 models) support both UEFI and
classic uboot booting, the devicetree data is always there, so using it
makes sure we ask for the same nvram file independent of how we booted.
This commit moves the brcmf_dmi_probe call to before the brcmf_of_probe
call, so that the latter can override the value of the first if both are
set.
Fixes: bd1e82bb42 ("brcmfmac: Set board_type from DMI on x86 based ...")
Cc: Peter Robinson <pbrobinson@gmail.com>
Tested-and-reported-by: Peter Robinson <pbrobinson@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The newest firmwares provide STA info using v7 of the struct. As v7
isn't backward compatible, a union is needed.
Even though brcmfmac does not use any of the new info it's important to
provide the proper struct buffer. Without this change new firmwares will
fallback to the very limited v3 instead of something in between such as
v4.
Signed-off-by: Dan Haab <dan.haab@luxul.com>
Reviewed-by: Rafał Miłecki <rafal@milecki.pl>
Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Kernel library has a common cordic algorithm which is identical
to internally implemented one, so use it and drop the duplicate
implementation.
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Priit Laes <plaes@plaes.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The cordic routine for calculating sines and cosines that was added in
commit 6f98e62a9f ("b43: update cordic code to match current specs")
contains an error whereby a quantity declared u32 can in fact go negative.
This problem was detected by Priit Laes who is switching b43 to use the
routine in the library functions of the kernel.
Fixes: 9865045403 ("b43: make cordic common (LP-PHY and N-PHY need it)")
Reported-by: Priit Laes <plaes@plaes.org>
Cc: Rafał Miłecki <zajec5@gmail.com>
Cc: Stable <stable@vger.kernel.org> # 2.6.34
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Priit Laes <plaes@plaes.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Current driver includes macro that is available from general cordic
library. Use that and drop unused duplicate and unneeded internal
definitions.
Signed-off-by: Priit Laes <plaes@plaes.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Now that these macros are in header file, we can eventually
clean up the duplicate macros present in the drivers that
utilize the same cordic algorithm implementation.
Also add CORDIC_ prefix to nonprefixed macros.
Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Priit Laes <plaes@plaes.org>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
* New FW debugging infrastructure;
* Some more work on 802.11ax;
* Improve support for multiple RF modules with 22000 devices;
* Remove an unused FW parameter;
* Other debugging improvements;
-----BEGIN PGP SIGNATURE-----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=8wf1
-----END PGP SIGNATURE-----
Merge tag 'iwlwifi-next-for-kalle-2018-11-23' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-next
second batch of iwlwifi patches intended for v4.21
* New FW debugging infrastructure;
* Some more work on 802.11ax;
* Improve support for multiple RF modules with 22000 devices;
* Remove an unused FW parameter;
* Other debugging improvements;
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEENrCndlB/VnAEWuH5k9IU1zQoZfEFAlv+uhcTHG1rbEBwZW5n
dXRyb25peC5kZQAKCRCT0hTXNChl8Q67B/4k/6WVMEssFStSEpC9asrqQs0Itra3
+eIiXrzGfpzO/Gg1O4LV2xUt7JzgLgRa8BBPH8wk+Q/QMOYZsP0qkocb2SWI+J31
JfJGa50l+Beyj8UdeLqZRt62cKCQIBXRaZ4O12ugGYNeQotFsSg4bFa1Gk9aW8Ke
YZT2zYTgD1yaQpBnUcbwnzJEf58vVjgH8zocpm40hlqsUKOJeHoAqUfyfj5RPioX
w9HAc/nDmsHAt32O650poJ851RK2dMNDTSKtUxKTH+nPI7HzdB5HXvlPFpHAf2SC
BrPYUJIOJGPLzhfTRTwAFCfM5C8/y/FtR0GD9vEctVDjSIrcH72aOnre
=NA7B
-----END PGP SIGNATURE-----
Merge tag 'linux-can-next-for-4.21-20181128' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next
Marc Kleine-Budde says:
====================
This is a pull request for net-next/master consisting of 18 patches.
The first patch is by Colin Ian King and fixes the spelling in the ucan
driver.
The next three patches target the xilinx driver. YueHaibing's patch
fixes the return type of ndo_start_xmit function. Two patches by
Shubhrajyoti Datta add support for the CAN FD 2.0 controllers.
Flavio Suligoi's patch for the sja1000 driver add support for the ASEM
CAN raw hardware.
Wolfram Sang's and Kuninori Morimoto's patches switch the rcar driver to
use SPDX license identifiers.
The remaining 111 patches improve the flexcan driver. Pankaj Bansal's
patch enables the driver in Kconfig on all architectures with IOMEM
support. The next four patches by me fix indention, add missing
parentheses and comments. Aisheng Dong's patches add self wake support
and document it in the DT bindings. The remaining patches by Pankaj
Bansal first fix the loopback support and prepare the driver for the
CAN-FD support needed for the LX2160A SoC. The actual CAN-FD support
will be added in a later patch series.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Trivial conflict in net/core/filter.c, a locally computed
'sdif' is now an argument to the function.
Signed-off-by: David S. Miller <davem@davemloft.net>
Cannot cast a u64 to a pointer on 32-bit without an intervening (long)
cast otherwise GCC warns.
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
