ERROR: "foo* bar" should be "foo *bar"
ERROR: "foo * bar" should be "foo *bar"
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
initial driver drop, provided by Siano Mobile Silicon, Inc.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The uvcvideo driver's uvc_v4l2_open() method is called from videodev's
video_open() function, which means it is called with the videodev_lock
mutex held. uvc_v4l2_open() then takes uvc_driver.open_mutex to check
dev->state and avoid racing against a device disconnect, which means
that open_mutex must nest inside videodev_lock.
However uvc_disconnect() takes the open_mutex around setting
dev->state and also around putting its device reference. However, if
uvc_disconnect() ends up dropping the last reference, it will call
uvc_delete(), which calls into the videodev code to unregister its
device, and this will end up taking videodev_lock. This opens a
(unlikely in practice) window for an AB-BA deadlock and also causes a
lockdep warning because of the lock misordering.
Fortunately there is no apparent reason to hold open_mutex when doing
kref_put() in uvc_disconnect(): if uvc_v4l2_open() runs before the
state is set to UVC_DEV_DISCONNECTED, then it will take another
reference to the device and kref_put() won't call uvc_delete; if
uvc_v4l2_open() runs after the state is set, it will run before
uvc_delete(), see the state, and return immediately -- uvc_delete()
does uvc_unregister_video() (and hence video_unregister_device(),
which is synchronized with videodev_lock) as its first thing, so there
is no risk of use-after-free in uvc_v4l2_open().
Bug diagnosed based on a lockdep warning reported by Romano Giannetti
<romano@dea.icai.upcomillas.es>.
Signed-off-by: Roland Dreier <roland@digitalvampire.org>
Signed-off-by: Laurent Pinchart <laurent.pinchart@skynet.be>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
drivers/media/video/uvc/uvc_v4l2.c: In function `uvc_v4l2_mmap':
drivers/media/video/uvc/uvc_v4l2.c:1035: warning: 'buffer' might be used uninitialized in this function
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Laurent Pinchart <laurent.pinchart@skynet.be>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
/home/v4l/master/v4l/gspca.c: In function 'gspca_frame_add':
/home/v4l/master/v4l/gspca.c:222: warning: format '%d' expects type 'int', but argument 2 has type 'long int'
/home/v4l/master/v4l/gspca.c: In function 'dev_read':
/home/v4l/master/v4l/gspca.c:1568: warning: format '%d' expects type 'int', but argument 2 has type 'size_t'
/home/v4l/master/v4l/gspca.c:1618: warning: format '%d' expects type 'int', but argument 3 has type 'size_t'
Acked-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
1) Remove a useless initialisation of 'i'
2) Avoid clearing the memory allocated twice (once in 'kcalloc', once
in 'sg_init_table')
3) Remove a test that can never trigger. The function returns NULL in
such a case, so we know that at this point 'pages[0]' != NULL
Signed-off-by: Christophe Jaillet <jaillet.christophe@wanadoo.fr>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Fix casts of pointers to integers of different sizes in the ivtv framebuffer
driver.
These were introduced in patch 38eb6ba5b8487d15b020fe391d324edd2b659b03.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The tvaudio driver is using "official" I2C device IDs for internal
purpose. There must be some historical reason behind this but anyway,
it shouldn't do that. As the stored values are never used, the easiest
way to fix the problem is simply to remove them altogether.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
I2C_HW_SMBUS_OVFX2 is referenced in ovcamchip_core.c, but no bus uses
this driver ID, so we can remove the reference. As far as I can see,
the Cypress FX2 webcam is handled by a different driver (dvb-usb).
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The following patch updates saa7134 driver to add support for AVerMedia
M103 MiniPCI DVB-T Hybrid card.
Signed-off-by: Massimo Piccioni <alsa@piccio.org>
[mchehab@infradead.org: fixed merge conflicts and a small codingstyle]
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The new revision of this board uses the same pci subsystem id as the first
revision, but uses a S5H1411 demodulator instead of the S5H1409.
In the case of the FusionHDTV7 Dual Express,
if s5h1409_attach fails, try s5h1411_attach.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
UVC devices can report button events. The uvcvideo driver depends on
CONFIG_INPUT to report events to the input layer. This patch removes the hard
dependency by introducing a new CONFIG_USB_VIDEO_CLASS_INPUT_EVDEV option.
Signed-off-by: Laurent Pinchart <laurent.pinchart@skynet.be>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
etoms: Do not declare the webcams declared by the driver et61x251.
sonixb, sonixj:
Do not declare the webcams declared by the driver sn9c102.
zc3xx: Do not declare the webcams declared by the driver zc0301.
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Also remove some blank lines that were used to split compat code at -devel
tree.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
All submitted URBs must be killed at suspend time, but URB buffers don't have
to be freed. Avoiding a free on suspend/reallocate on resume lowers the presure
on system memory.
Signed-off-by: Laurent Pinchart <laurent.pinchart@skynet.be>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The swap device might still be asleep, so memory allocated in the resume
handler must use GFP_NOIO. Thanks to Oliver Neukum for catching and reporting
this bug.
Signed-off-by: Laurent Pinchart <laurent.pinchart@skynet.be>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Thanks to Oliver Neukum for catching and reporting this bug.
Signed-off-by: Laurent Pinchart <laurent.pinchart@skynet.be>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
pac207: Set the sizeimage to the max value for 352x288.
Signed-off-by: Hans de Goede <j.w.r.degoede@hhs.nl>
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
videodev2: New pixfmt
pac207: Remove the specific decoding.
main: get_buff_size operation added for the subdriver.
Signed-off-by: Hans de Goede <j.w.r.degoede@hhs.nl>
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The low (half) res modes of the spca561 are not spca561 compressed, but are
raw bayer, this patches fixes this and adds a PIX_FMT define for the GBRG
bayer format used by the spca561 in low res mode.
Signed-off-by: Hans de Goede <j.w.r.degoede@hhs.nl>
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Done for conex, etoms, pac7311, sonixj, t613 and tv8532.
Code cleanup for some other subdrivers.
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Change the Yuan MPC718 cards entry to use the correct GPIO pin for resetting
the Xceive 3028 tuner. Thanks to Brian Hope <brian@hopefamily.info> for
taking the time and figuring out which pin to use.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
cx18: Add a missing reset recovery delay in cx18-i2c.c after
the final deassert.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Added ID vendor/product for Clone Digital Webcam 11043.
Thanks to Ivan Brasil Fuzzer <ivan@fuzzer.com.br> for testing and data collection.
Signed-off-by: Douglas Schilling Landgraf <dougsland@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
After adding support for AVerTVHD Volar, DVB_USB_CXUSB must
select MEDIA_TUNER_MXL5005S if !DVB_FE_CUSTOMISE
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
main: Remove some vidioc_xx traces.
main: read() did not work (user irq instead of mmap irq).
main: Lack of v4l1 compat.
main: Process loop inside kernel when no frame arriving.
main: Double qbuf in read() when too many buffered frames.
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
When switching video standard, ensure that video GOP size remains
appropriately configured.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Conexant graciously gave us permission to redistribute the
firmware. Update the documentation where the firmware can be
downloaded.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Reverted the 'Fix unintended auto configurations in cx18-av-core' patch,
instead disable the auto config completely.
Fix a bug in cx18_av_vbi_setup() where the standard tests were done
in the wrong order.
Tested with NTSC-M, PAL-BG, PAL-I, PAL-DK, PAL-M, PAL-Nc, SECAM-DK,
SECAM-L and SECAM-BG. The last one does not work at the moment due to
a tda9887.c bug.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
main: V4L2_PIX_FMT_SPCA501 is compressed (thanks to Hans de Goede)
main: return 0 when no change on vidioc_s_fmt_cap (thanks to Hans de Goede)
pac207: cleanup
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- Protect format change when streaming active.
- Protect USB exchanges on close.
- Set a timeout in frame wait.
- Have only one capture file and free the resources when closing this file.
- Simplify the URB buffer.
- Don't reset the control values at open time in pac207.
- Fix compilation warnings of stk014.
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
pac207 added.
Check status on mutex lock.
Call back on frame dequeue.
Free the resources on last close only.
Avoid URB and ISOC errors on close.
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The MPEG controls could not be enumerated and so could not be read or set
through the v4l2-ctl utility or shown in control panels.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Composite was originally mis-labelled as name_comp1,
so it should be simply redone as name_comp,
with its now corrected attributes.
Signed-off-by: Tim Farrington <timf@iinet.net.au>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Add initial support for this device. The AGC and tracking filter
settings for the mxl5003 are known to be wrong, but it generally works.
Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Allow the following configuration, by passing clock_polarity_flip = 2:
Enable FEC automatic reset. Disable spectrum inversion.
Enable viterbi resynchronization. Set polarity indicator high.
Enable error flag insertion.
Thanks to Daniel Gimpelevich, for discovering that this configuration
is used on the AVerMedia AVerTVHD Volar.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
CC: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
As reported by Stephen Rothwell <sfr@canb.auug.org.au>:
drivers/media/dvb/ttpci/budget-ci.c:50:21: error: tda827x.h: No such file or directory
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
... but two ancient drivers had not noticed.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
split the suckers into kernel-memory and user-memory versions,
annotate both properly.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Annotations + stop saa7146_i2c from playing fast and loose with
reuse of ->cpu_addr for host-endian.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
According to RFC 4326 (4.1) D-bit is MSB in net-endian 16bit.
dvb_net.c did
/* Set D-bit for CRC32 verification,
* if it was set originally. */
ulen |= 0x0080;
which works of little-endian (htons(1<<15) is 0x0080 there), but breaks
on big-endian.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
It was primarily developed by Dean Anderson with only a little bit of
guidance and cleanup by Greg.
Signed-off-by: Dean Anderson <dean@sensoray.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
[mchehab@infradead.org: fixed renamed callbacks]
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
em28xx-cards.c
em28xx-input.c
em28xx-video.c
em28xx.h
- Add support for the PointNix Intra-Oral Camera, which required addition of
a construct for reading the "snapshot" button (provided on the em2860 and
em2880 chips, but this is the first case where I have seen it actually used
in a product). The button is wired to pin 56 on the em2880.
http://www.pointnix.com/ENG/dental/product_02.asp
Thanks to Roberto Mantovani <rmantovani@libero.it> for testing the changes
Signed-off-by: Devin Heitmueller <devin.heitmueller@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Convert cx23885-417 to use video_ioctl2
Signed-off-by: Douglas Schilling Landgraf <dougsland@gmail.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
V4L2_CID_PRIVATE_BASE controls are not allowed when called from
VIDIOC_S/G_EXT_CTRL as extended controls use a better mechanism
for private controls. But still allow it when called from the
VIDIOC_G/S_CTRL to extended control conversion in video_ioctl2()
for backwards compatibility.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
cx18: Improved Raptor card audio input routing defintions, so that muxer values
matched cx18_gpio() values for tuner, line in 1, and radio and added LED
indication of selected audio input. Audio line in 2 doesn't work as it uses
the not yet supported 2nd I2S port. Tuner/FM Radio AF is mono until SIF
support is fixed.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
videodev converts old-style controls to an extended control so the ivtv and
cx18 drivers no longer have to handle both.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- add sanity checks for the extended controls argument.
- if the driver only supports extended controls, then convert
old-style controls to an extended control callback.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Thanks to Randy Dunlap for reporting this.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- add radio definition
- reset the audio firmware (required for this board, harmless for the
others)
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The cx18 can support transport streams with newer firmwares. Add a TS
capability to the generic cx2341x module.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Completely rely on the video_ioctl2 debugging facilities rather than
doing it ourselves.
Fill in some missing fields in ivtv with VIDIOC_G_FBUF.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Various ioctl debugging fixes and improvements:
- use %x rather than %d for control IDs and bitmask fields
- make two arrays const
- show the whole control array for the ext_ctrl ioctls
- print pix_fmt for V4L2_BUF_TYPE_VIDEO_OUTPUT
- show full type name rather than an integer
- fix CROPCAP debugging
- fix G/S_TUNER debugging
- show error code in case of an error
- other small cleanups
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The xc5000 firmware download process can be slow on certain devices.
Add a module option, "init_fw" to perform the firmware download during
xc5000_attach(), which would get the firmware download over with well
before any tune request is made.
When this option is enabled, it will reduce the time it takes to get a
signal lock during the first tune after driver load, but will add a few
seconds to the driver initialization.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The IVTV_IOC_DMA_FRAME ioctl fails to correctly 'start' the decoder. Although
yuv output will be correct, some functions which should be disabled while the
decoder is in use remain enabled. This can result in hardware registers being
corrupted, causing problems with the mpeg decoder. This patch ensures the
decoder 'start' sequence is called, disabling these functions until the
device is closed.
Signed-off-by: Ian Armstrong <ian@iarmst.demon.co.uk>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
write() operations to the yuv device may not always 'start' the decoder.
Although yuv output will be correct, some functions which should be disabled
while the decoder is in use remain enabled. This can result in hardware
registers being corrupted, causing problems with the mpeg decoder. This patch
simply moves the existing decoder 'start' sequence to earlier in the write()
handler.
Signed-off-by: Ian Armstrong <ian@iarmst.demon.co.uk>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
If the capture is scaled, then the video_temporal_filter is set to 0
by the cx2341x.c module since otherwise you would get ghosting.
However, this was also done in the VIDIOC_S_FMT ioctl which meant that
the video_temporal_filter control was reset to 0 or 8 each time S_FMT
was called. This was old code that should have been removed a long time
ago.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This avoids the need of memsets in the ivtv/cx18 drivers.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
cx18: convert driver to use video_ioctl2(). Pushed down ioctl debug
messages and priority checks as well. Still left serialization lock in
place for now. #if 0'ed out sliced vbi ioctl code for now.
Patch heavily based on similar changes made to ivtv by Hans Verkuil.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Based on an initial conversion patch from Douglas Landgraf.
Signed-off-by: Douglas Schilling Landgraf <dougsland@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
A number of V4L drivers have a mod param to specify their preferred minors.
This is because it is often desirable for applications to have a static /dev
name for a particular device. However, using minors has several disadvantages:
1) the requested minor may already be taken
2) using a mod param is driver specific
3) it requires every driver to add a param
4) requires configuration by hand
This patch introduces an "index" attribute that when combined with udev rules
can create static device paths like this:
/dev/v4l/by-path/pci-0000\:00\:1d.2-usb-0\:1\:1.0-video0
/dev/v4l/by-path/pci-0000\:00\:1d.2-usb-0\:1\:1.0-video1
/dev/v4l/by-path/pci-0000\:00\:1d.2-usb-0\:1\:1.0-video2
$ ls -la /dev/v4l/by-path/pci-0000\:00\:1d.2-usb-0\:1\:1.0-video0
lrwxrwxrwx 1 root root 12 2008-04-28 00:02 /dev/v4l/by-path/pci-0000:00:1d.2-usb-0:1:1.0-video0 -> ../../video1
These paths are steady across reboots and should be resistant to rearranging
across Kernel versions.
video_register_device_index is available to drivers to request a
specific index number.
Signed-off-by: Brandon Philips <bphilips@suse.de>
Signed-off-by: Kees Cook <kees@outflux.net>
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Support the bundled remote control of the TT DVB-C 1501
Thanks-to: SG <SiestaGomez@web.de>
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Removed some obsolete definitions and one unused variable.
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The build option, MEDIA_TUNER_CUSTOMIZE, allows us to disable tuner drivers
that would have otherwise been selected by default. This is an advanced
customization option that should be disabled by default.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Auto-selects tda10023, for budget-ci, if !DVB_FE_CUSTOMISE. This is needed for
Technotrend budget C-1501 dvb board.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The following experimental patch adds support for the technotrend budget
C-1501 dvb-c card. The parameters used to configure the tda10023 demod
chip are largely determined experimentally, but works quite for me in my
initial tests.
Signed-off-by: Sigmund Augdal <sigmund@snap.tv>
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Clean up the use of structure templates in bttv-i2c. For one thing, a
real template is supposed to be read-only. And in some cases it's more
efficient to initialize the few fields we need individually.
This clean-up shrinks bttv-i2c.o by 29% (x86_64).
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Clean up the use of structure templates in zoran_card. For one thing,
a real template is supposed to be read-only. And in some cases it's
more efficient to initialize the few fields we need individually.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Ronald S. Bultje <rbultje@ronald.bitfreak.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- support for Anysee E30C Plus rev 0.4
- set IO port E
- set correct TS mode
- change deltaf according to latest Windows driver
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Split the Beholder M6 family to different models. Because M6 hasn`t RDS, M63
has chip with AC3 codec, M6 Extra has other type of HF module.
Add correct data for support MPEG encoder.
Signed-off-by: Beholder Intl. Ltd. Dmitry Belimov <d.belimov@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Rework saa7134_enable_i2s function. Remove vendor specific data.
Configure I2S output port specific for model of SAA7133/5-SAA7134.
I think it is more good.
Renamed definition of I2S audio output control register. It`s SAA7133/5 register
Start video port after configuring procedure.
Signed-off-by: Beholder Intl. Ltd. Dmitry Belimov <d.belimov@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- Separate the newer variant of the HVR-900 into its own device profile
because it has a Micronas DRX397 instead of the Zarlink demod. This
doesn't make the device work, but at least we don't try to initialize it
as though it had the Zarlink device.
Signed-off-by: Devin Heitmueller <devin.heitmueller@gmail.com>
[mchehab@infradead.org: avoid compilation breakage at mainstream, where drx397xD.h doesn't exist yet]
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch brings the following changes:
- this now finally adds hardware frequency seek support
Signed-off-by: Tobias Lorenz <tobias.lorenz@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch brings the following changes:
- afc indication:
device has no indication whether freq is too low or too high
therefore afc always return 1, when freq is wrong
Signed-off-by: Tobias Lorenz <tobias.lorenz@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch brings the following changes:
- comment on how to listen to an usb audio device
(i get so many questions about that...)
- code cleanup (error handling, more warnings, spacing, ...)
Signed-off-by: Tobias Lorenz <tobias.lorenz@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch brings the following changes:
- version bumped to 1.0.8 for all the following patches
- si470x_get_freq now returns errno
Signed-off-by: Tobias Lorenz <tobias.lorenz@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
this patch brings the following changes:
- move the global disconnect lock into the device structure
- code cleanup (spaces to tabs, long line splits, ...)
Signed-off-by: Tobias Lorenz <tobias.lorenz@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Only one frontend is enabled right now. The second frontend can lock,
but transport doesn't work yet. The device will be supported as a
single tuner device until the second frontend is working.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This file was renamed but we forgot to change it in the comments.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- update license comments
- change MODULE_DESCRIPTION from device specific to chipset specific
- correct debug switch from deb_rc to deb_info
- correct MPEG2 stream interval from 1.25 to 1
- change frontend_attach error code from -EIO to -ENODEV
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The naming for the callbacks that handle the VIDIOC_ENUM_FMT and
VIDIOC_S/G/TRY_FMT ioctls was very confusing. Renamed it to match
the v4l2_buf_type name.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
There was no vidioc_try_fmt_sliced_vbi_output, instead vidioc_try_fmt_vbi_output
was reused.
The VIDIOC_ENUMOUTPUT handling was missing altogether, even though the callback
existed.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The default videodev behavior for VIDIOC_G_STD is not correct for all devices.
Add a new callback that drivers can use instead.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
__video_do_ioctl incorrectly zeroed the tuner field of v4l2_frequency and
did not zero the full fmt union of v4l2_format.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Back in the early days of the pvrusb2 driver, the kernel class
mechanism in use for the sysfs interface had no means to pass
per-attribute information to the show / store functions. This forced
me to implement a horrible ugly thunking mechanism (i.e. infer the
missing data through the use of dedicated cookie cutter bounce
functions). However now we're using a better mechanism which also
passes enough additional information to the show / store functions
that we no longer need the hack. So eliminate all the crap. Yay!
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The driver enforces a "quiet period" on the encoder in certain
situations before attempting to operate it. This seems to help avoid
video encoding errors / corruption. The quiet period was 50msec, but
through experimentation it has been observed to improve further if the
interval is increased to 100msec.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This is primarily a cosmetic change to make it easier to change some
of the time constants used in the driver.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Separate gpio_init field and xceive_pin and combine the two when
the gpio is initialized. So there is no longer any need to set the
xceive pin in the gpio_init values, simplifying the creation of a
new card definition.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Thanks to Peter Brandt for doing the necessary tests to fill out the card
definition!
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
snprinf() takes the trailing \0 into account in its length calculations,
so there is no need to subtract 1 to the buffer size.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Add invertation of image mirroring register bits to default
configuration.
This is useful when the camera module is e.g. mounted upside down.
Signed-off-by: Sakari Ailus <sakari.ailus@nokia.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
write() operations to the ivtv framebuffer will now attempt to use DMA if the
amount of data to copy is >= 4096 bytes. This change effectively depreciates
the need for the proprietary IVTVFB_IOC_DMA_FRAME ioctl since a write() of
sufficient size will do the same thing.
Signed-off-by: Ian Armstrong <ian@iarmst.demon.co.uk>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The pvrusb2 driver initially sets the tuner to known broadcast frequencies
in the Chicago area, to ease driver testing for the maintainer.
This patch keeps those default frequencies, but allows them to be altered
via modprobe option. This allows the same ease and convenience for testing
multiple pvrusb2 devices one after another under other conditions and areas.
For instance, the default initial frequency, 175.25 MHz, might not
necessarily be valid on all cable television networks, but usually will be a
valid NTSC broadcast channel.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch will fix the following sparse warnings:
/home/benli/sparse/bnx2.c:297:8: warning: symbol 'val' shadows an earlier one
/home/benli/sparse/bnx2.c:286:60: originally declared here
/home/benli/sparse/bnx2.c:7461:7: warning: symbol 'i' shadows an earlier one
/home/benli/sparse/bnx2.c:7265:10: originally declared here
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change allows the first TX ring (CID 16) and the first TSS TX ring
(CID 32) to be used concurrently. Before this change, we could get TSO
errors when both TX rings were used concurrently.
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the recent changes to tx mutiqueue, e1000 was not calling
netif_start_queue() before calling netif_wake_queue().
This causes an oops during loading of the driver.
(Based on commit d55b53fff0
("igb/ixgbe/e1000e: resolve tx multiqueue bug").)
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the recent changes to tx mutiqueue, igb/ixgbe/e1000e was not calling
netif_tx_start_all_queues() before calling netif_tx_wake_all_queues().
This causes an issue during loading of the driver.
In addition, updated e1000e to use the updated tx mutliqueue api.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 94d9842403.
Alan says it's not appropriate to remove this driver,
Adrian Bunk also agrees with this revert.
Signed-off-by: David S. Miller <davem@davemloft.net>
The private area of a netdev is now at a fixed offset once more.
Unfortunately, some assumptions that netdev_priv() == netdev->priv
crept back into the tree. In particular this happened in the
loopback driver. Make it use netdev->ml_priv.
Signed-off-by: David S. Miller <davem@davemloft.net>
This effectively "flips the switch" by making the core networking
and multiqueue-aware drivers use the new TX multiqueue structures.
Non-multiqueue drivers need no changes. The interfaces they use such
as netif_stop_queue() degenerate into an operation on TX queue zero.
So everything "just works" for them.
Code that really wants to do "X" to all TX queues now invokes a
routine that does so, such as netif_tx_wake_all_queues(),
netif_tx_stop_all_queues(), etc.
pktgen and netpoll required a little bit more surgery than the others.
In particular the pktgen changes, whilst functional, could be largely
improved. The initial check in pktgen_xmit() will sometimes check the
wrong queue, which is mostly harmless. The thing to do is probably to
invoke fill_packet() earlier.
The bulk of the netpoll changes is to make the code operate solely on
the TX queue indicated by by the SKB queue mapping.
Setting of the SKB queue mapping is entirely confined inside of
net/core/dev.c:dev_pick_tx(). If we end up needing any kind of
special semantics (drops, for example) it will be implemented here.
Finally, we now have a "real_num_tx_queues" which is where the driver
indicates how many TX queues are actually active.
With IGB changes from Jeff Kirsher.
Signed-off-by: David S. Miller <davem@davemloft.net>
