Kernel software timestamping requires that the driver calls skb_tx_timestamp
just before passing the skb to the HW MAC layer. This patch adds this call.
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch allows to enable/disable HW timestamping for incoming and/or
outgoing packets. It adds and initializes all structs and callbacks
needed by kernel TS API.
To enable/disable HW timestamping appropriate ioctl should be used.
Currently HWTSTAMP_FILTER_ALL/NONE and HWTSAMP_TX_ON/OFF only are
supported.
When enabling TS on receive flow - VLAN stripping will be disabled.
Also were made all relevant changes in RX/TX flows to consider TS request
and plant HW timestamps into relevant structures.
mlx4_ib was fixed to compile with new mlx4_cq_alloc() signature.
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Read HCA frequency, read PCI clock bar and offset, map internal clock to
PCI bar.
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add new device capability for timestamping support and query FW to retrieve it.
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a protocol argument to the VLAN packet tagging functions. In case of HW
tagging, we need that protocol available in the ndo_start_xmit functions,
so it is stored in a new field in the skb. The new field fits into a hole
(on 64 bit) and doesn't increase the sks's size.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change the rx_{add,kill}_vid callbacks to take a protocol argument in
preparation of 802.1ad support. The protocol argument used so far is
always htons(ETH_P_8021Q).
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename the hardware VLAN acceleration features to include "CTAG" to indicate
that they only support CTAGs. Follow up patches will introduce 802.1ad
server provider tagging (STAGs) and require the distinction for hardware not
supporting acclerating both.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Expose a new API mlx4_srq_lookup() to retrive a SRQ based on its
number. This API is needed in the mlx4_ib driver CQ polling logic,
when a work completion is associated with a XRC TGT QP. Since a
target QP may redirect to more than one XRC SRQ, the srq field in the
QP has no usage and the real XRC SRQ need to be retrived using the
information from the XRCETH IB header which is placed in the HW CQE.
Signed-off-by: Shlomo Pongratz <shlomop@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
When setting MTU in SRIOV mode add ETH, VLAN and FCS header length
to the maximum MTU obtained from QUERY_DEV_CAP.
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The different steering modes are global to the device, with DMFS
being introduced after SRIOV was merged. Hence, SRIOV guests running
legacy / older Linux kernels or non-Linux drivers may provide
B0 steering directives when the hypervisor is using DMFS and fail.
Under B0 only L2 steering rules are allowed, hence B0 is a subset of DMFS.
Use this fact to enable such legacy guests to run by modifying the SRIOV
B0 steering wrapper to translate guest B0 directives to DMFS ones when
the device uses DMFS. The translated B0 rule has to be kept in the
resource tracker as a B0 object to allow for lookup in case of detach.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A pre-step for supporting guests that use B0 steering over a hypervisor
that runs in DMFS (device managed flow steering mode). Add helper function
which allows to translate L2 attachments / detachments provided in B0 mode
to DMFS rules.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When our getdcbx entry is called, DCB_CAP_DCBX_HOST should be advertized too.
Cc: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enable the DCB ETS ops only when supported by the firmware. For older firmware/cards
which don't support ETS, advertize only PFC DCB ops.
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added readable description for the DPDP and port sensing device capabilities.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 6bbb6d9 "net/mlx4_en: Optimize Rx fast path filter checks" introduced a regression
under which the MAC address read from the card was not converted correctly
(the most significant byte was not handled), fix that.
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Yan Burman <yanb@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull to get the thermal netlink multicast group name fix, otherwise
the assertion added in net-next to netlink to detect that kind of bug
makes systems unbootable for some folks.
Signed-off-by: David S. Miller <davem@davemloft.net>
VF QPs must not be released when they have steering rules attached to them.
For that end, introduce a reference count field to the QP object in the
SRIOV resource tracker which is incremented/decremented when steering rules
are attached/detached to it. QPs can be released by VF only when their
ref count is zero.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
One of the resource tracker code paths was wrongly using int and not u64
for resource tracking IDs, fix it.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the ethtool flow steering rules cleanup to be carried out before
releasing the RX QPs.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On the resource tracker cleanup flow, the DMFS rules must be deleted before we
destroy the QPs, else the HW may attempt doing packet steering to non existent QPs.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the mask is wrongly set in the MAP_EQ wrapper, fix that.
Without the fix any EQ number above 511 is mapped to one below 511.
Signed-off-by: Moshe Lazer <moshel@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I believe these error messages are already logged
on allocation failure by warn_alloc_failed and so
get a dump_stack on OOM.
Remove the unnecessary additional error logging.
Around these deletions:
o Alignment neatening.
o Remove unnecessary casts of dma_alloc_coherent.
o Hoist assigns from ifs.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/intel/e1000e/netdev.c
Minor conflict in e1000e, a line that got fixed in 'net'
has been removed in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Emitting netdev_alloc_skb and netdev_alloc_skb_ip_align OOM
messages is unnecessary as there is already a dump_stack
after allocation failures.
Other trivial changes around these removals:
Convert a few comparisons of pointer to 0 to !pointer.
Change flow to remove unnecessary label.
Remove now unused variable.
Hoist assignment from if.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 37706996 "mlx4_en: fix allocation of CPU affinity reverse-map" fixed
a bug when mlx4_dev->caps.comp_pool is larger from the device rx rings, but
introduced a regression.
When the mlx4_core is activating its "legacy mode" (e.g when running in SRIOV
mode) w.r.t to EQs/IRQs usage, comp_pool becomes zero and we're crashing on
divide by zero alloc_cpu_rmap.
Fix that by enabling RFS only when running in non-legacy mode.
Reported-by: Yan Burman <yanb@mellanox.com>
Cc: Kleber Sacilotto de Souza <klebers@linux.vnet.ibm.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure we cleanup all MAC related resources (entries in the port MAC
table and steering rules) when stopping a port or when the driver is unloaded.
The leak was introduced by commit 07cb4b0a "net/mlx4_en: Manage hash of MAC
addresses per port".
Signed-off-by: Yan Burman <yanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove unnecessary use of workqueue for the device MAC address setting
flow, and fix a race when setting MAC address which was introduced by
commit c07cb4b0a "net/mlx4_en: Manage hash of MAC addresses per port"
The race happened when mlx4_en_replace_mac was being executed in parallel
with a successive call to ndo_set_mac_address, e.g witn an A/B/A MAC
setting configuration test, the third set fails.
With this change we also properly report an error if set MAC fails.
Signed-off-by: Yan Burman <yanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The set_param_l function assumes casting a u64 pointer to a u32 pointer
allows to access the lower 32bits, but it results in writing the upper
32 bits on big endian systems.
The fixed function reads the upper 32 bits of the 64 argument, and or's
them with the 32 bits of the 32-bit value passed to the function.
Since this is now a "read-modify-write" operation, we got many
"unintialized variable" warnings which needed to be fixed as well.
Reported-by: Alexander Schmidt <alexschm@de.ibm.com>.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Older kernels detect DMFS (device-managed flow steering) from the HCA
device capability directly, regardless of whether the capability was
enabled in INIT_HCA, this is fixed by commit 7b8157bed "mlx4_core: Adjustments
to Flow Steering activation logic for SR-IOV"
To protect against guests running kernels without this fix, the host driver
should turn off the DMFS capability bit in mlx4_QUERY_DEV_CAP_wrapper.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Guests kernels may not correctly detect if DMFS (device-enabled flow steering) is
activated by the host. If DMFS is activated, the master should return error to guests
which try to use the B0-steering flow calls (mlx4_QP_ATTACH).
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove driver specific fdb hadlers since they are the same as
the default ones.
CC: Amir Vadai <amirv@mellanox.com>
CC: Yan Burman <yanb@mellanox.com>
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I'm not sure why, but the hlist for each entry iterators were conceived
list_for_each_entry(pos, head, member)
The hlist ones were greedy and wanted an extra parameter:
hlist_for_each_entry(tpos, pos, head, member)
Why did they need an extra pos parameter? I'm not quite sure. Not only
they don't really need it, it also prevents the iterator from looking
exactly like the list iterator, which is unfortunate.
Besides the semantic patch, there was some manual work required:
- Fix up the actual hlist iterators in linux/list.h
- Fix up the declaration of other iterators based on the hlist ones.
- A very small amount of places were using the 'node' parameter, this
was modified to use 'obj->member' instead.
- Coccinelle didn't handle the hlist_for_each_entry_safe iterator
properly, so those had to be fixed up manually.
The semantic patch which is mostly the work of Peter Senna Tschudin is here:
@@
iterator name hlist_for_each_entry, hlist_for_each_entry_continue, hlist_for_each_entry_from, hlist_for_each_entry_rcu, hlist_for_each_entry_rcu_bh, hlist_for_each_entry_continue_rcu_bh, for_each_busy_worker, ax25_uid_for_each, ax25_for_each, inet_bind_bucket_for_each, sctp_for_each_hentry, sk_for_each, sk_for_each_rcu, sk_for_each_from, sk_for_each_safe, sk_for_each_bound, hlist_for_each_entry_safe, hlist_for_each_entry_continue_rcu, nr_neigh_for_each, nr_neigh_for_each_safe, nr_node_for_each, nr_node_for_each_safe, for_each_gfn_indirect_valid_sp, for_each_gfn_sp, for_each_host;
type T;
expression a,c,d,e;
identifier b;
statement S;
@@
-T b;
<+... when != b
(
hlist_for_each_entry(a,
- b,
c, d) S
|
hlist_for_each_entry_continue(a,
- b,
c) S
|
hlist_for_each_entry_from(a,
- b,
c) S
|
hlist_for_each_entry_rcu(a,
- b,
c, d) S
|
hlist_for_each_entry_rcu_bh(a,
- b,
c, d) S
|
hlist_for_each_entry_continue_rcu_bh(a,
- b,
c) S
|
for_each_busy_worker(a, c,
- b,
d) S
|
ax25_uid_for_each(a,
- b,
c) S
|
ax25_for_each(a,
- b,
c) S
|
inet_bind_bucket_for_each(a,
- b,
c) S
|
sctp_for_each_hentry(a,
- b,
c) S
|
sk_for_each(a,
- b,
c) S
|
sk_for_each_rcu(a,
- b,
c) S
|
sk_for_each_from
-(a, b)
+(a)
S
+ sk_for_each_from(a) S
|
sk_for_each_safe(a,
- b,
c, d) S
|
sk_for_each_bound(a,
- b,
c) S
|
hlist_for_each_entry_safe(a,
- b,
c, d, e) S
|
hlist_for_each_entry_continue_rcu(a,
- b,
c) S
|
nr_neigh_for_each(a,
- b,
c) S
|
nr_neigh_for_each_safe(a,
- b,
c, d) S
|
nr_node_for_each(a,
- b,
c) S
|
nr_node_for_each_safe(a,
- b,
c, d) S
|
- for_each_gfn_sp(a, c, d, b) S
+ for_each_gfn_sp(a, c, d) S
|
- for_each_gfn_indirect_valid_sp(a, c, d, b) S
+ for_each_gfn_indirect_valid_sp(a, c, d) S
|
for_each_host(a,
- b,
c) S
|
for_each_host_safe(a,
- b,
c, d) S
|
for_each_mesh_entry(a,
- b,
c, d) S
)
...+>
[akpm@linux-foundation.org: drop bogus change from net/ipv4/raw.c]
[akpm@linux-foundation.org: drop bogus hunk from net/ipv6/raw.c]
[akpm@linux-foundation.org: checkpatch fixes]
[akpm@linux-foundation.org: fix warnings]
[akpm@linux-foudnation.org: redo intrusive kvm changes]
Tested-by: Peter Senna Tschudin <peter.senna@gmail.com>
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Cc: Wu Fengguang <fengguang.wu@intel.com>
Cc: Marcelo Tosatti <mtosatti@redhat.com>
Cc: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull networking fixes from David Miller:
1) ping_err() ICMP error handler looks at wrong ICMP header, from Li
Wei.
2) TCP socket hash function on ipv6 is too weak, from Eric Dumazet.
3) netif_set_xps_queue() forgets to drop mutex on errors, fix from
Alexander Duyck.
4) sum_frag_mem_limit() can deadlock due to lack of BH disabling, fix
from Eric Dumazet.
5) TCP SYN data is miscalculated in tcp_send_syn_data(), because the
amount of TCP option space was not taken into account properly in
this code path. Fix from yuchung Cheng.
6) MLX4 driver allocates device queues with the wrong size, from Kleber
Sacilotto.
7) sock_diag can access past the end of the sock_diag_handlers[] array,
from Mathias Krause.
8) vlan_set_encap_proto() makes incorrect assumptions about where
skb->data points, rework the logic so that it works regardless of
where skb->data happens to be. From Jesse Gross.
9) Fix gianfar build failure with NET_POLL enabled, from Paul
Gortmaker.
10) Fix Ipv4 ID setting and checksum calculations in GRE driver, from
Pravin B Shelar.
11) bgmac driver does:
int i;
for (i = 0; ...; ...) {
...
for (i = 0; ...; ...) {
effectively corrupting the outer loop index, use a seperate
variable for the inner loops. From Rafał Miłecki.
12) Fix suspend bugs in smsc95xx driver, from Ming Lei.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (35 commits)
usbnet: smsc95xx: rename FEATURE_AUTOSUSPEND
usbnet: smsc95xx: fix broken runtime suspend
usbnet: smsc95xx: fix suspend failure
bgmac: fix indexing of 2nd level loops
b43: Fix lockdep splat on module unload
Revert "ip_gre: propogate target device GSO capability to the tunnel device"
IP_GRE: Fix GRE_CSUM case.
VXLAN: Use tunnel_ip_select_ident() for tunnel IP-Identification.
IP_GRE: Fix IP-Identification.
net/pasemi: Fix missing coding style
vmxnet3: fix ethtool ring buffer size setting
vmxnet3: make local function static
bnx2x: remove dead code and make local funcs static
gianfar: fix compile fail for NET_POLL=y due to struct packing
vlan: adjust vlan_set_encap_proto() for its callers
sock_diag: Simplify sock_diag_handlers[] handling in __sock_diag_rcv_msg
sock_diag: Fix out-of-bounds access to sock_diag_handlers[]
vxlan: remove depends on CONFIG_EXPERIMENTAL
mlx4_en: fix allocation of CPU affinity reverse-map
mlx4_en: fix allocation of device tx_cq
...
- SRP error handling fixes from Bart Van Assche
- Implementation of memory windows for mlx4 from Shani Michaeli
- Lots of cxgb4 HW driver fixes from Vipul Pandya
- Make iSER work for virtual functions, other fixes from Or Gerlitz
- Fix for bug in qib HW driver from Mike Marciniszyn
- IPoIB fixes from me, Itai Garbi, Shlomo Pongratz, Yan Burman
- Various cleanups and warning fixes from Julia Lawall, Paul Bolle, Wei Yongjun
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=RAQw
-----END PGP SIGNATURE-----
Merge tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
Pull infiniband update from Roland Dreier:
"Main batch of InfiniBand/RDMA changes for 3.9:
- SRP error handling fixes from Bart Van Assche
- Implementation of memory windows for mlx4 from Shani Michaeli
- Lots of cxgb4 HW driver fixes from Vipul Pandya
- Make iSER work for virtual functions, other fixes from Or Gerlitz
- Fix for bug in qib HW driver from Mike Marciniszyn
- IPoIB fixes from me, Itai Garbi, Shlomo Pongratz, Yan Burman
- Various cleanups and warning fixes from Julia Lawall, Paul Bolle,
Wei Yongjun"
* tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband: (41 commits)
IB/mlx4: Advertise MW support
IB/mlx4: Support memory window binding
mlx4: Implement memory windows allocation and deallocation
mlx4_core: Enable memory windows in {INIT, QUERY}_HCA
mlx4_core: Disable memory windows for virtual functions
IPoIB: Free ipoib neigh on path record failure so path rec queries are retried
IB/srp: Fail I/O requests if the transport is offline
IB/srp: Avoid endless SCSI error handling loop
IB/srp: Avoid sending a task management function needlessly
IB/srp: Track connection state properly
IB/mlx4: Remove redundant NULL check before kfree
IB/mlx4: Fix compiler warning about uninitialized 'vlan' variable
IB/mlx4: Convert is_xxx variables in build_mlx_header() to bool
IB/iser: Enable iser when FMRs are not supported
IB/iser: Avoid error prints on EAGAIN registration failures
IB/iser: Use proper define for the commands per LUN value advertised to SCSI ML
IB/uverbs: Implement memory windows support in uverbs
IB/core: Add "type 2" memory windows support
mlx4_core: Propagate MR deregistration failures to caller
mlx4_core: Rename MPT-related functions to have mpt_ prefix
...
Implement MW allocation and deallocation in mlx4_core and mlx4_ib.
Pass down the enable bind flag when registering memory regions.
Signed-off-by: Haggai Eran <haggaie@mellanox.com>
Signed-off-by: Shani Michaeli <shanim@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Add memory windows-related code to INIT_HCA and QUERY_HCA.
Signed-off-by: Haggai Eran <haggaie@mellanox.com>
Signed-off-by: Shani Michaeli <shanim@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Do not enable memory windows allocation for virtual functions.
In addition, add a few safety checks, such as:
* Verifying the PD of a new MPT matches the VF.
* Making sure binding memory window isn't enabled for FMRs, and
that new memory windows are not FMR themselves.
Signed-off-by: Haggai Eran <haggaie@mellanox.com>
Signed-off-by: Shani Michaeli <shanim@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
The mlx4_en driver allocates the number of objects for the CPU affinity
reverse-map based on the number of rx rings of the device. However,
mlx4_assign_eq() calls irq_cpu_rmap_add() as many times as IRQ's are
assigned to EQ's, which can be as large as mlx4_dev->caps.comp_pool. If
caps.comp_pool is larger than rx_ring_num we will eventually hit the
BUG_ON() in cpu_rmap_add().
Fix this problem by allocating space for the maximum number of CPU
affinity reverse-map objects we might want to add.
Signed-off-by: Kleber Sacilotto de Souza <klebers@linux.vnet.ibm.com>
Acked-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The memory to hold the network device tx_cq is not being allocated with
the correct size in mlx4_en_init_netdev(). It should use MAX_TX_RINGS
instead of MAX_RX_RINGS. This can cause problems if the number of tx
rings being used is greater than MAX_RX_RINGS.
Signed-off-by: Kleber Sacilotto de Souza <klebers@linux.vnet.ibm.com>
Acked-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull trivial tree from Jiri Kosina:
"Assorted tiny fixes queued in trivial tree"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (22 commits)
DocBook: update EXPORT_SYMBOL entry to point at export.h
Documentation: update top level 00-INDEX file with new additions
ARM: at91/ide: remove unsused at91-ide Kconfig entry
percpu_counter.h: comment code for better readability
x86, efi: fix comment typo in head_32.S
IB: cxgb3: delay freeing mem untill entirely done with it
net: mvneta: remove unneeded version.h include
time: x86: report_lost_ticks doesn't exist any more
pcmcia: avoid static analysis complaint about use-after-free
fs/jfs: Fix typo in comment : 'how may' -> 'how many'
of: add missing documentation for of_platform_populate()
btrfs: remove unnecessary cur_trans set before goto loop in join_transaction
sound: soc: Fix typo in sound/codecs
treewide: Fix typo in various drivers
btrfs: fix comment typos
Update ibmvscsi module name in Kconfig.
powerpc: fix typo (utilties -> utilities)
of: fix spelling mistake in comment
h8300: Fix home page URL in h8300/README
xtensa: Fix home page URL in Kconfig
...
MR deregistration fails when memory windows are bound to the MR.
Handle such failures by propagating them to the caller ULP.
Signed-off-by: Haggai Eran <haggaie@mellanox.com>
Signed-off-by: Shani Michaeli <shanim@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
The MPT - Memory Protection Table - is used by both memory windows and
memory regions. Hence, all MPT references are relevant for both types
of memory objects. Rename the relevant functions to start with mpt_
instead of the current mr_ prefix.
Signed-off-by: Haggai Eran <haggaie@mellanox.com>
Signed-off-by: Shani Michaeli <shanim@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
When a user adds bridge neighbors, allow him to specify VLAN id.
If the VLAN id is not specified, the neighbor will be added
for VLANs currently in the ports filter list. If no VLANs are
configured on the port, we use vlan 0 and only add 1 entry.
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Acked-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Synchronize with 'net' in order to sort out some l2tp, wireless, and
ipv6 GRE fixes that will be built on top of in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
alloc failures already get standardized OOM
messages and a dump_stack.
For the affected mallocs around these OOM messages:
Converted kmallocs with multiplies to kmalloc_array.
Converted a kmalloc/memcpy to kmemdup.
Removed now unused stack variables.
Removed unnecessary parentheses.
Neatened alignment.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Arend van Spriel <arend@broadcom.com>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Acked-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix issue in Mellanox driver related to BQL. netdev_tx_reset_queue
was not being called in certain situations where the device was
being start and stopped. Moved netdev_tx_reset_queue from the reset
device path to mlx4_en_free_tx_buf which is where the rings are
cleaned in a reset (specifically from device being stopped).
Signed-off-by: Tom Herbert <therbert@google.com>
Acked-By: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for setting embedded switch fdb in case of SRIOV, by
implementing ndo_fdb_{add, del, dump}. This will allow to use
bridged configuration with multi-function. In order to add VM MAC
to the eSwitch fdb, the following command may be used over the relevant function interface:
bridge fdb add <MAC> permanent self dev <IFACE>
Signed-off-by: Yan Burman <yanb@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement and advertise unicast MAC filtering, such that setting macvlan
instance over mlx4_en interfaces will not require the networking core
to put mlx4_en devices in promiscuous mode.
If for some reason adding a unicast address filter fails e.g as of missing space in
the HW mac table, the device forces itself into promiscuous mode (and out of this
forced state when enough space is available).
Signed-off-by: Yan Burman <yanb@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As a preparation step for supporting multiple unicast addresses, store MAC addresses in hash table.
Remove the radix tree for MAC addresses per QP, as it's not in use.
Signed-off-by: Yan Burman <yanb@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to having more than one unicast MAC per port, we need to keep track
of the previous MAC address in the flow of ndo_set_mac_address,
so that mlx4_en_replace_mac will know what to replace.
Signed-off-by: Yan Burman <yanb@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, mlx4_en_do_set_multicast serves as the ndo_set_rx_mode entry for mlx4_en,
doing all related work. Split it to few calls, one per required functionality
(e.g multicast, promiscuous, etc) and rename some structures and calls
to use rx_mode notation instead of multicast.
Signed-off-by: Yan Burman <yanb@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move low level code that deals with management of Ethernet MACs and QPs from mlx4_core to mlx4_en.
Also convert the new functions to deal with MACs in form of char array instead of u64.
Actual functions moved:
mlx4_replace_mac
mlx4_get_eth_qp
mlx4_put_eth_qp
To conduct this change, some functionality had to be exported from the core,
the following functions were added:
mlx4_get_base_qp
__mlx4_replace_mac (low level function for CX1/A0 compatibility)
Signed-off-by: Yan Burman <yanb@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make the code consistent in regard to error messages
not spanning multiple lines.
Signed-off-by: Yan Burman <yanb@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, RX path code that does RX filtering is not optimized
and does an expensive conversion. In order to use ether_addr_equal_64bits
which is optimized for such cases, we need the MAC address kept by the device
to be in the form of unsigned char array instead of u64. Store the MAC address
as unsigned char array and convert to/from u64 out of the fast path when needed.
Side effect of this is that we no longer need priv->mac, since it's the same
as dev->dev_addr.
This optimization was suggested by Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Yan Burman <yanb@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently there are relatively complex conditional checks in the fast path,
for TX loopback enabling and resulting RX filter logic.
Move elaborate if's out of data path, replace them with a single flag
for each state and update that state from appropriate places.
Also, in native (non SRIOV) mode and not in loopback or in selftest,
there is no need to try and filter out packets that HW loopback-ed,
as in native mode we do not loopback packets anymore.
Signed-off-by: Yan Burman <yanb@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Fix mlx4 VFs not working on old guests because of 64B CQE changes
- Fix ill-considered sparse fix for qib
- Fix IPoIB crash due to skb double destruct introduced in 3.8-rc1
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=bmKU
-----END PGP SIGNATURE-----
Merge tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
Pull IB regression fixes from Roland Dreier:
- Fix mlx4 VFs not working on old guests because of 64B CQE changes
- Fix ill-considered sparse fix for qib
- Fix IPoIB crash due to skb double destruct introduced in 3.8-rc1
* tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
IB/qib: Fix for broken sparse warning fix
mlx4_core: Fix advertisement of wrong PF context behaviour
IPoIB: Fix crash due to skb double destruct
Commit 08ff32352d ("mlx4: 64-byte CQE/EQE support") introduced a
regression where older guest VF drivers failed to load even when
64-byte EQEs/CQEs are disabled, since the PF wrongly advertises the
new context behaviour anyway. The failure looks like:
mlx4_core 0000:00:07.0: Unknown pf context behaviour
mlx4_core 0000:00:07.0: Failed to obtain slave caps
mlx4_core: probe of 0000:00:07.0 failed with error -38
Fix this by basing this advertisement on dev->caps.flags, which is the
operational capabilities used by the QUERY_FUNC_CAP command wrapper
(dev_cap->flags holds the firmware capabilities).
Reported-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
ip_eth_mc_map function can't be used when CONFIG_INET isn't defined.
Fixed compilation error by adding CONFIG_INET define check before using the
function.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Propagate return value of mlx4_en_ethtool_add_mac_rule_by_ipv4 in case of
failure.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
alloc failures already get standardized OOM
messages and a dump_stack.
Convert kzalloc's with multiplies to kcalloc.
Convert kmalloc's with multiplies to kmalloc_array.
Fix a few whitespace defects.
Convert a constant 6 to ETH_ALEN.
Use parentheses around sizeof.
Convert vmalloc/memset to vzalloc.
Remove now unused size variables.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Under heavy CPU load, changing, ring size/mtu/etc. could result in transmit
timeout, since stop-start port might take more than 10 seconds.
Calling netif_detach_device to prevent tx queue transmit timeout.
netif_detach_device() is not called under ndo_stop, because netif_carrier_off
will prevent the timeout, and device should not be marked as not present, or
else user won't be able to start it later on.
CC: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mac reassignments should only be done when not supported by the firmware. To
accomplish that, checking firmware capability bit to know whether we should
reassign macs in the driver.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Firmware dynamically changes flow steering hash configuration from covering
L2 only to "full" L2/L3/L4 mode needed. The dynamic change allows the driver
to set hard coded hash configuration which is changed by the firmware from L2
to L2/L3/L4 when attaching the first L3/L4 flow steering rule and back to L2
when there are no more such rules.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As part of the driver unload flow, all steering rules must be deleted,
make sure to remove the rules that were set through ethtool.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Attaching steering rules while the interface is down is an invalid operation, block it.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The vlan mask field should be validated and assigned according to the field
size which is 12 bits. Also replace the numeric 0xfff mask with existing kernel
macro.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When attaching flow steering rules via Ethtool accept only valid vlans IDs e.g
in the range: [0,4095].
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Destination mac is a mandatory specification for ip/udp steering rules.
When attaching multicast steering rules via ethtool the unicast mac of the
interface was added to the rule specification instead of the multicast mac.
The following commit sets the corresponding multicast mac for the rule multicast ip.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The allow_loopback flag was wrongly set using arithmetic bit operation, change
the code to use logical bit operation.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some of the fields for struct mlx4_net_trans_rule_hw_ctrl were packed into u32
and accessed through bit field operations. Expose and access them directly as
u8.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bring in the 'net' tree so that we can get some ipv4/ipv6 bug
fixes that some net-next work will build upon.
Signed-off-by: David S. Miller <davem@davemloft.net>
filters_lock might have been used while it was re-initialized.
Moved filters_lock and filters_list initialization to init_netdev instead of
alloc_resources which is called every time the device is configured.
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a possible race where the TX completion handler can clean the
entire TX queue between the decision that the queue is full and actually
closing it. To avoid this situation, check again if the queue is really
full, if not, reopen the transmit and continue with sending the packet.
CC: Eric Dumazet <edumazet@google.com>
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.com>
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Returning 0 (success) when in fact we are aborting the load, leads to kernel
panic when unloading the module. Fix that by returning the actual error code.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The device multicast list is protected by netif_addr_lock_bh in the networking core, we should
use this locking practice in mlx4_en too.
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Reviewed-by: Yevgeny Petrilin <yevgenyp@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When port is stopped and flow steering mode is not device managed: promisc QP
rule wasn't removed from MCG table.
Added code to remove it in all flow steering modes.
In addition, promsic rule removal should be in stop port and not in start
port - moved it accordingly.
Signed-off-by: Aviad Yehezkel <aviadye@mellanox.com>
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Performing the DUMP_ETH_STATS firmware command outside the lock leads to kernel
panic when data structures such as RX/TX rings are freed in parallel, e.g when
one changes the mtu or ring sizes.
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
remove redundant code from build_inline_wqe()
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-By: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The lines
if (mlx4_is_mfunc(dev)) {
nreq = 2;
} else {
which hard code the number of requested msi-x vectors under multi-function
mode to two can be removed completely, since the firmware sets num_eqs and
reserved_eqs appropriately Thus, the code line:
nreq = min_t(int, dev->caps.num_eqs - dev->caps.reserved_eqs, nreq);
is by itself sufficient and correct for all cases. Currently, for mfunc
mode num_eqs = 32 and reserved_eqs = 28, hence four vectors will be enabled.
This triples (one vector is used for the async events and commands EQ) the
horse power provided for processing of incoming packets on netdev RSS scheme,
IO initiators/targets commands processing flows, etc.
Reviewed-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 5b4c4d3686 "mlx4_en: Allow communication between functions on
same host" introduced a regression under which a bridge acting as vSwitch
whose uplink is an mlx4 Ethernet device become non-operative in native
(non sriov) mode. This happens since broadcast ARP requests sent by VMs
were loopback-ed by the HW and hence the bridge learned VM source MACs
on both the VM and the uplink ports.
The fix is to place the DMAC in the send WQE only under SRIOV/eSwitch
configuration or when the device is in selftest.
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Yan Burman <yanb@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
perm_addr is initialized correctly in register_netdevice() so to init it in
drivers is no longer needed.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
Device managed flow steering will be enabled only under administrator
directive provided through setting the existing module parameter
log_num_mgm_entry_size to -1 (if the device actually supports flow
steering). If flow steering isn't requested or not available, the
driver will use the value of log_num_mgm_entry_size and B0 steering.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Separate flow steering capability detection from the decision to activate.
For the master (and for native), detect the flow steering capability
in mlx4_dev_cap, but activate the appropriate steering type in a new
function choose_flow_steering() based on detected data.
For VFs, activate flow steering based on what was actually activated
by the master, where that info is obtained via QUERY_HCA. This fixes
the current VF detection which is wrongly based on QUERY_DEV_CAP.
Also, for SR-IOV mode, if flow steering may be activated, do so only
if the max number of QPs per rule is sufficient to satisfy one
subscription per VF. If not, fall back to B0 mode. This is needed to
serve registrations done by L2 network drivers such as mlx4_en and
IPoIB when the network stack attempts to join to multicast groups such
as all-hosts or the IPoIB broadcast group.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
The error flow of the flow steering wrapper had a typo which caused
the wrong firmware command to be called, fix it.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Since VFs may be mapped to VMs which aren't trusted entities, flow
steering rules attached through the wrapper on behalf of VFs must be
checked to make sure that the specified QP number is assigned to that
VF. Also, make sure to keep the QP busy till the end of the operation
from the resource tracker point of view.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
- A good chunk of Bart Van Assche's SRP fixes
- UAPI disintegration from David Howells
- mlx4 support for "64-byte CQE" hardware feature from Or Gerlitz
- Other miscellaneous fixes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=TQK2
-----END PGP SIGNATURE-----
Merge tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
Pull infiniband upate from Roland Dreier:
"First batch of InfiniBand/RDMA changes for the 3.8 merge window:
- A good chunk of Bart Van Assche's SRP fixes
- UAPI disintegration from David Howells
- mlx4 support for "64-byte CQE" hardware feature from Or Gerlitz
- Other miscellaneous fixes"
Fix up trivial conflict in mellanox/mlx4 driver.
* tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband: (33 commits)
RDMA/nes: Fix for crash when registering zero length MR for CQ
RDMA/nes: Fix for terminate timer crash
RDMA/nes: Fix for BUG_ON due to adding already-pending timer
IB/srp: Allow SRP disconnect through sysfs
srp_transport: Document sysfs attributes
srp_transport: Simplify attribute initialization code
srp_transport: Fix attribute registration
IB/srp: Document sysfs attributes
IB/srp: send disconnect request without waiting for CM timewait exit
IB/srp: destroy and recreate QP and CQs when reconnecting
IB/srp: Eliminate state SRP_TARGET_DEAD
IB/srp: Introduce the helper function srp_remove_target()
IB/srp: Suppress superfluous error messages
IB/srp: Process all error completions
IB/srp: Introduce srp_handle_qp_err()
IB/srp: Simplify SCSI error handling
IB/srp: Keep processing commands during host removal
IB/srp: Eliminate state SRP_TARGET_CONNECTING
IB/srp: Increase block layer timeout
RDMA/cm: Change return value from find_gid_port()
...
Pull trivial branch from Jiri Kosina:
"Usual stuff -- comment/printk typo fixes, documentation updates, dead
code elimination."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (39 commits)
HOWTO: fix double words typo
x86 mtrr: fix comment typo in mtrr_bp_init
propagate name change to comments in kernel source
doc: Update the name of profiling based on sysfs
treewide: Fix typos in various drivers
treewide: Fix typos in various Kconfig
wireless: mwifiex: Fix typo in wireless/mwifiex driver
messages: i2o: Fix typo in messages/i2o
scripts/kernel-doc: check that non-void fcts describe their return value
Kernel-doc: Convention: Use a "Return" section to describe return values
radeon: Fix typo and copy/paste error in comments
doc: Remove unnecessary declarations from Documentation/accounting/getdelays.c
various: Fix spelling of "asynchronous" in comments.
Fix misspellings of "whether" in comments.
eisa: Fix spelling of "asynchronous".
various: Fix spelling of "registered" in comments.
doc: fix quite a few typos within Documentation
target: iscsi: fix comment typos in target/iscsi drivers
treewide: fix typo of "suport" in various comments and Kconfig
treewide: fix typo of "suppport" in various comments
...
Implement destination MAC rule extension for L3/L4 rules in
flow steering. Usefull for vSwitch/macvlan configurations.
Signed-off-by: Yan Burman <yanb@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Get rid of full_mac, zero_mac in favour of
is_zero_ether_addr and is_broadcast_ether_addr.
Signed-off-by: Yan Burman <yanb@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The __dev* removal patches for the network drivers ended up messing up
the function prototypes for a bunch of drivers. This patch fixes all of
them back up to be properly aligned.
Bonus is that this almost removes 100 lines of code, always a nice
surprise.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
CONFIG_HOTPLUG is going away as an option. As result the __dev*
markings will be going away.
Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support to changing number of rx/tx channels using
ethtool ('ethtool -[lL]'). Where the number of tx channels specified in ethtool
is the number of rings per user priority - not total number of tx rings.
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to re-set tx moderation information after calling set_ringparam
else default tx moderation will be used.
Also avoid related code duplication, by putting it in a utility function.
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The slave_state_lock spinlock is used in both interrupt context and
process context, hence irq locking must be used. Found by lockdep.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Roland Dreier <roland@purestorage.com>
ConnectX-3 devices can use either 64- or 32-byte completion queue
entries (CQEs) and event queue entries (EQEs). Using 64-byte
EQEs/CQEs performs better because each entry is aligned to a complete
cacheline. This patch queries the HCA's capabilities, and if it
supports 64-byte CQEs and EQES the driver will configure the HW to
work in 64-byte mode.
The 32-byte vs 64-byte mode is global per HCA and not per CQ or EQ.
Since this mode is global, userspace (libmlx4) must be updated to work
with the configured CQE size, and guests using SR-IOV virtual
functions need to know both EQE and CQE size.
In case one of the 64-byte CQE/EQE capabilities is activated, the
patch makes sure that older guest drivers that use the QUERY_DEV_FUNC
command (e.g as done in mlx4_core of Linux 3.3..3.6) will notice that
they need an update to be able to work with the PPF. This is done by
changing the returned pf_context_behaviour not to be zero any more. In
case none of these capabilities is activated that value remains zero
and older guest drivers can run OK.
The SRIOV related flow is as follows
1. the PPF does the detection of the new capabilities using
QUERY_DEV_CAP command.
2. the PPF activates the new capabilities using INIT_HCA.
3. the VF detects if the PPF activated the capabilities using
QUERY_HCA, and if this is the case activates them for itself too.
Note that the VF detects that it must be aware to the new PF behaviour
using QUERY_FUNC_CAP. Steps 1 and 2 apply also for native mode.
User space notification is done through a new field introduced in
struct mlx4_ib_ucontext which holds device capabilities for which user
space must take action. This changes the binary interface so the ABI
towards libmlx4 exposed through uverbs is bumped from 3 to 4 but only
when **needed** i.e. only when the driver does use 64-byte CQEs or
future device capabilities which must be in sync by user space. This
practice allows to work with unmodified libmlx4 on older devices (e.g
A0, B0) which don't support 64-byte CQEs.
In order to keep existing systems functional when they update to a
newer kernel that contains these changes in VF and userspace ABI, a
module parameter enable_64b_cqe_eqe must be set to enable 64-byte
mode; the default is currently false.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
