setup_decoder_defaults() doesn't really care about the input
port. All it needs to know is if the input port is s-video or
not.
As the caller function already knows that, just pass a boolean
instead.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Let's set the the audio routing also at stream start. With this change,
we don't risk enabling the analog demux while not streaming, reducing
the risk of interfering with a DVB demux that might be happening.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The same demod is used on both analog and digital mode. We should
not let the commands for analog mode to happen while the device
is in digital mode. So, monitor it via streamon.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The input mode is used not only inside the setup_decoder_defaults()
but also at au8522_*_mode routines.
So, move it one level up. As an advantage, we can now group the
function that sets the input into just one.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The analog part of au0828 is missing the tuner Kconfig dependency.
That makes the device to not work while in analog mode.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The saa7134 driver uses core-locking, so there is no longer any need
to use the ioctl op instead of the unlocked_ioctl op. This change
was forgotten for the saa7134-empress.c, so fix this.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Wrong value used in same cases for the aspect ratio.
Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Cc: stable@vger.kernel.org # for v3.12 and up
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
First 8 bytes belonging to firmware image were hard-coded and uploaded
by the driver mistakenly. Introduce new corrected firmware file and
remove those 8 bytes from the driver.
New firmware image could be extracted from the PCTV 292e driver CD
using following command:
$ dd if=/TVC 6.4.8/Driver/PCTV Empia/emOEM.sys ibs=1 skip=1089408 count=2728 of=dvb-demod-si2168-02.fw
$ md5sum dvb-demod-si2168-02.fw
d8da7ff67cd56cd8aa4e101aea45e052 dvb-demod-si2168-02.fw
$ sudo cp dvb-demod-si2168-02.fw /lib/firmware/
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Fix following warnings:
si2157_cmd_execute() warn: add some parenthesis here?
si2157_cmd_execute() warn: maybe use && instead of &
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Fix following warnings:
si2168_cmd_execute() warn: add some parenthesis here?
si2168_cmd_execute() warn: maybe use && instead of &
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Add the basic GPLv2+ license notice to the copyright headers at the top
of all the source files in the img-ir driver.
Reported-by: David Härdeman <david@hardeman.nu>
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The sh_mobile_ceu_camera and sh_mobile_csi2 drivers are only useful on
SuperH and shmobile unless build testing.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This patch change MACH_MX27 dependency to SOC_IMX27 for MX2 camera
driver, since MACH_MX27 symbol is scheduled for removal.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
That driver hasn't been really maintained for a long time. It doesn't
compile in any way, it includes non-existent headers, has no users,
and marked as "BROKEN" more than year. Due to these factors, mx1_camera
is now removed from the tree.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The R-Car Video Input driver is only useful on shmobile unless build
testing.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Cc: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The platform data is a single word, so simply copy
it into the device's private data structure than
keeping a copy of the pointer.
This will make changing to device-tree binding
easier as it is one allocation instead of two.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
devm_kzalloc() allocations are freed when the device is unbound. But if a
certain path fails and the allocated memory cannot be used anyway it is
better to free it explicitly immediately. This patch does exactly this if
asynchronous group probing in scan_async_group() fails after memory has
been allocated.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Calibrate the signal strength to dB.
For this callibration, I used adapter 0 (antenna 1), connected
via a normal cable to a DTF-2111 generator.
The same cabling and RF generator connected to adapter 1
(antenna 2) has a difference of +3dBm (signal was stronger
there).
Yet, changing the RF for a difference of, let's say, 6dB
reflected on a 6dB difference at the measured signal, with
is good.
So, the signal strengh can indeed be used to measure the
antenna gain, if the antenna is repositioned. It is
not precise to measure the absolute dBm value, however.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Adds DVBv5 stats support. For now, just mimic whatever dib8000
does, as they're very similar, with regards to statistics.
However, dib7000p_get_time_us() likely require some
adjustments, as I didn't actually reviewed the formula
for it to work with DVB-T. Still, better than nothing,
as latter patches can improve it.
This patch also doesn't show the signal strength in dB
yet. The code is already there, but it requires to be
callibrated.
A latter patch will do the calibration.
It seems that this patch is also a bug fix: Before this
patch, the frontend were not tuning with some userspace
tools. I suspect that dib7000p firmware or hardware
internally expects that the statistics to be collected,
in order for it to work. With this patch, the DVB core
will always retrive statistics, even if userspace doesn't
request. So, it makes the device work on all tested apps.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Exporting multiple symbols don't work as it causes compilation
breakages, due to the way dvb_attach() works.
The bug happens when:
CONFIG_DVB_DIB8000=m
CONFIG_DVB_USB_DIB0700=y
As a bonus, dib8000 won't be loaded anymore if the device uses
a different frontend, reducing the memory footprint.
Tested with both Pixelview PV-D231 and MyGica S870.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Well, what we call as "foo_attach" is the method that should
be called by the dvb_attach() macro.
It should be noticed that the name "dvb_attach" is really a
bad name and don't express what it does.
dvb_attach() basically does three things, if the frontend is
compiled as a module:
- It lookups for the module that it is known to have the
given symbol name and requests such module;
- It increments the module usage (anonymously - so lsmod
doesn't print who loaded the module);
- after loading the module, it runs the function associated
with the dynamic symbol.
When compiled as builtin, it just calls the function given to it.
As dvb_attach() increments refcount, it can't be (easily)
called more than once for the same module, or the kernel
will deny to remove the module, because refcount will never
be zeroed.
In other words, the function name given to dvb_attach()
should be one single symbol that will always be called
before any other function on that module to be used.
For almost all DVB frontends, there's just one function,
but, on dib8000, there are several exported symbols.
We need to get rid of all those direct calls, because they
cause compilation breakages when bridge is builtin and
frontend is module, we'll need to add a new function that
will be the first one to be called, whatever initialization
is needed.
So, let's rename this function, in order to prepare for
a next patch that will add a new attach() function that
will be the only one exported by this module.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Exporting multiple symbols don't work as it causes compilation
breakages, due to the way dvb_attach() works.
This were reported several times, like:
drivers/built-in.o: In function `cxusb_dualdig4_rev2_tuner_attach':
>> cxusb.c:(.text+0x27d4b5): undefined reference to `dib7000p_get_i2c_master'
drivers/built-in.o: In function `dib7070_set_param_override':
cxusb.c:(.text+0x27d5a5): undefined reference to `dib0070_wbd_offset'
>> cxusb.c:(.text+0x27d5be): undefined reference to `dib7000p_set_wbd_ref'
drivers/built-in.o: In function `dib7070_tuner_reset':
>> cxusb.c:(.text+0x27d5f9): undefined reference to `dib7000p_set_gpio'
drivers/built-in.o: In function `cxusb_dualdig4_rev2_frontend_attach':
>> cxusb.c:(.text+0x27df5c): undefined reference to `dib7000p_i2c_enumeration'
In this specific report:
CONFIG_DVB_USB_CXUSB=y
CONFIG_DVB_DIB7000P=m
But the same type of bug can happen if:
CONFIG_DVB_DIB7000P=m
and one of the bridge drivers is compiled builtin (cxusb, cx23885-dvb
and/or dib0700).
As a bonus, dib7000p won't be loaded anymore if the device uses
a different frontend, reducing the memory footprint.
Tested with Hauppauge Nova-TD (2 frontends).
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Well, what we call as "foo_attach" is the method that should
be called by the dvb_attach() macro.
It should be noticed that the name "dvb_attach" is really a
bad name and don't express what it does.
dvb_attach() basically does three things, if the frontend is
compiled as a module:
- It lookups for the module that it is known to have the
given symbol name and requests such module;
- It increments the module usage (anonymously - so lsmod
doesn't print who loaded the module);
- after loading the module, it runs the function associated
with the dynamic symbol.
When compiled as builtin, it just calls the function given to it.
As dvb_attach() increments refcount, it can't be (easily)
called more than once for the same module, or the kernel
will deny to remove the module, because refcount will never
be zeroed.
In other words, the function name given to dvb_attach()
should be one single symbol that will always be called
before any other function on that module to be used.
For almost all DVB frontends, there's just one function.
However, the dib7000p initialization can require up to 3
functions to be called:
- dib7000p_get_i2c_master;
- dib7000p_i2c_enumeration;
- dib7000p_init (before this patch dib7000_attach).
(plus a bunch of other functions that the bridge driver will
need to call).
As we need to get rid of all those direct calls, because they
cause compilation breakages when bridge is builtin and
frontend is module, we'll need to add a new function that
will be the first one to be called, whatever initialization
is needed.
So, let's rename the function that probes and init the hardware
to dib7000p_init.
A latter patch will add a new dib7000p_attach that will be
used as originally conceived by dvb_attach() way.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The dvb_attach() was unbalanced, as there was no dvb_dettach. Ok,
on current cases, the dettach is done by dvbdev, but that are some
future corner cases where we may need to do this before registering
the frontend.
So, add a dvb_detach() and use it at dvb_frontend.c.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Change handling of signal_lock on rs2000. Use ibuf[2] to detect
lock as there is a longer wait for lock to appear in ibuf[6].
Remove last_key and key_timeout and use jiffies plus 60ms
to detect that streaming is still active.
If the current jiffies is time_after the interrupt urb overdue and
clear signal lock.
This results in far faster recovery of lock and streaming.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Replace resource handling in the driver with managed device resource.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The I2C address of the sensor device was in the middle of the sub-device
name and not in the end as it should have been. The smiapp sub-device names
will change from e.g. "vs6555 1-0010 pixel array" to "vs6555 pixel array
1-0010".
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Remove bogus 'numbuffers' and 'bufsize' module options. The number of buffers and
buffer sizes are determined by VIDIOC_REQBUFS and VIDIOC_S_FMT and the amount of
available memory (in the case of the MMAP stream I/O mode) and not by module
options.
These module params are a left-over from the original montavista code that used
these parameters to pre-allocate the memory needed for the buffers. The code that
allocated those buffers was never upstreamed since by the time the drivers were
added to the kernel the TI cmem module could be used in combination with the
USERPTR mode to reserve and pass physically contiguous memory pointers around.
These days of course CMA is used instead of cmem.
This patch removes these module options altogether since they no longer do what
they originally were designed for. They should never have been part of the
upstreamed code in the first place, so they've been pointless ever since
2.6.32 when this driver first appeared in the mainline kernel.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The field is assigned but never read, remove it.
This fixes a bug caused by the struct vb2_buffer field not being be the
very first field of the vsp1_video_buffer buffer structure as required
by videobuf2.
Cc: stable@vger.kernel.org
Reported-by: Takanari Hayama <taki@igel.co.jp>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Pull OMAP3 updates from Mauro Carvalho Chehab:
"Some driver improvements on OMAP3. This series depend on some iommu
patches already merged"
* 'topic/omap3isp' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (26 commits)
[media] omap3isp: Rename isp_buffer isp_addr field to dma
[media] omap3isp: Move to videobuf2
[media] v4l: vb2: Add a function to discard all DONE buffers
[media] omap3isp: Cancel all queued buffers when stopping the video stream
[media] omap3isp: Move buffer irqlist to isp_buffer structure
[media] omap3isp: Move queue irqlock to isp_video structure
[media] omap3isp: Move queue mutex to isp_video structure
[media] omap3isp: queue: Don't build scatterlist for kernel buffer
[media] omap3isp: Use the ARM DMA IOMMU-aware operations
[media] omap3isp: queue: Use sg_alloc_table_from_pages()
[media] omap3isp: queue: Map PFNMAP buffers to device
[media] omap3isp: queue: Fix the dma_map_sg() return value check
[media] omap3isp: queue: Allocate kernel buffers with dma_alloc_coherent
[media] omap3isp: queue: Inline the ispmmu_v(un)map functions
[media] omap3isp: queue: Merge the prepare and sglist functions
[media] omap3isp: queue: Use sg_table structure
[media] omap3isp: queue: Move IOMMU handling code to the queue
[media] omap3isp: video: Set the buffer bytesused field at completion time
[media] omap3isp: ccdc: Use the DMA API for FPC
[media] omap3isp: ccdc: Use the DMA API for LSC
...
Pull updates and DT support for media engines from Mauro Carvalho Chehab.
For Analog Devices ADV7604 and the Renesas VSP1 video processing engines.
* 'topic/vsp1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
[media] v4l: vsp1: Add DT support
[media] v4l: vsp1: Add DT bindings documentation
[media] v4l: vsp1: Add BRU support
[media] v4l: vsp1: Support multi-input entities
[media] v4l: vsp1: uds: Enable scaling of alpha layer
[media] v4l: vsp1: Remove unexisting rt clocks
* 'topic/adv76xx' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (21 commits)
[media] adv7604: Add LLC polarity configuration
[media] adv7604: Set HPD GPIO direction to output
[media] adv7604: Add endpoint properties to DT bindings
[media] adv7604: Add DT support
[media] adv7604: Specify the default input through platform data
[media] adv7604: Support hot-plug detect control through a GPIO
[media] adv7604: Sort headers alphabetically
[media] adv7604: Replace *_and_or() functions with *_clr_set()
[media] adv7604: Store I2C addresses and clients in arrays
[media] adv7604: Inline the to_sd function
[media] v4l: subdev: Remove deprecated video-level DV timings operations
[media] adv7604: Remove deprecated video-level DV timings operations
[media] adv7604: Add pad-level DV timings support
[media] adv7604: Make output format configurable through pad format operations
[media] adv7604: Add sink pads
[media] adv7604: Remove subdev control handlers
[media] adv7604: Add adv7611 support
[media] adv7604: Cache register contents when reading multiple bits
[media] adv7604: Add 16-bit read functions for CP and HDMI
[media] adv7604: Don't put info string arrays on the stack
...
Pull media updates from Mauro Carvalho Chehab:
"This contains:
- a new frontend/tuner driver set for si2168 and sa2157
- Videobuf 2 core now supports DVB too
- A new gspca sub-driver (dtcs033)
- saa7134 is now converted to use videobuf2
- add support for 4K timings
- several other driver fixes and improvements
PS. This pull request is shorter than usual, partly because I have
some other patches on topic branches that I'll be sending you later
this week"
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (286 commits)
[media] au0828-dvb: restore its permission to 644
[media] xc5000: delay tuner sleep to 5 seconds
[media] xc5000: Don't use whitespace before tabs
[media] xc5000: fix CamelCase
[media] xc5000: Don't wrap msleep()
[media] xc5000: get rid of positive error codes
[media] au0828: reset streaming when a new frequency is set
[media] au0828: Improve debug messages for urb_completion
[media] au0828: Cancel stream-restart operation if frontend is disconnected
[media] dib0700: fix RC support on Hauppauge Nova-TD
[media] USB: as102_usb_drv.c: Remove useless return variables
[media] v4l: Fix documentation of V4L2_PIX_FMT_H264_MVC and VP8 pixel formats
[media] m5mols: Replace missing header
[media] staging: lirc: Fix sparse warnings
[media] fix mceusb endpoint type identification/handling
[media] az6027: Added the PID for a new revision of the Elgato EyeTV Sat DVB-S Tuner
[media] DocBook media: fix typo
[media] adv7604: Add missing include to linux/types.h
[media] v4l: Validate fields in the core code for subdev EDID ioctls
[media] v4l: Add support for DV timings ioctls on subdev nodes
...
Here is the big USB driver pull request for 3.16-rc1.
Nothing huge here, but lots of little things in the USB core, and in
lots of drivers. Hopefully the USB power management will be work better
now that it has been reworked to do per-port power control dynamically.
There's also a raft of gadget driver updates and fixes, CONFIG_USB_DEBUG
is finally gone now that everything has been converted over to the
dynamic debug inteface, the last hold-out drivers were cleaned up and
the config option removed. There were also other minor things all
through the drivers/usb/ tree, the shortlog shows this pretty well.
All have been in linux-next, including the very last patch, which came
from linux-next to fix a build issue on some platforms.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iEYEABECAAYFAlONYEMACgkQMUfUDdst+ynxvgCggMQBhN5icth8Y5hFglNNaISN
c4AAoMHR2kb62U1plylLbPnboQTjfcl0
=fG6y
-----END PGP SIGNATURE-----
Merge tag 'usb-3.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb into next
Pull USB driver updates from Greg KH:
"Here is the big USB driver pull request for 3.16-rc1.
Nothing huge here, but lots of little things in the USB core, and in
lots of drivers. Hopefully the USB power management will be work
better now that it has been reworked to do per-port power control
dynamically. There's also a raft of gadget driver updates and fixes,
CONFIG_USB_DEBUG is finally gone now that everything has been
converted over to the dynamic debug inteface, the last hold-out
drivers were cleaned up and the config option removed. There were
also other minor things all through the drivers/usb/ tree, the
shortlog shows this pretty well.
All have been in linux-next, including the very last patch, which came
from linux-next to fix a build issue on some platforms"
* tag 'usb-3.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (314 commits)
usb: hub_handle_remote_wakeup() only exists for CONFIG_PM=y
USB: orinoco_usb: remove CONFIG_USB_DEBUG support
USB: media: lirc: igorplugusb: remove CONFIG_USB_DEBUG support
USB: media: streamzap: remove CONFIG_USB_DEBUG
USB: media: redrat3: remove CONFIG_USB_DEBUG usage
USB: media: redrat3: remove unneeded tracing macro
usb: qcserial: add additional Sierra Wireless QMI devices
usb: host: max3421-hcd: Use module_spi_driver
usb: host: max3421-hcd: Allow platform-data to specify Vbus polarity
usb: host: max3421-hcd: fix "spi_rd8" uses dynamic stack allocation warning
usb: host: max3421-hcd: Fix missing unlock in max3421_urb_enqueue()
usb: qcserial: add Netgear AirCard 341U
Documentation: dt-bindings: update xhci-platform DT binding for R-Car H2 and M2
usb: host: xhci-plat: add xhci_plat_start()
usb: host: max3421-hcd: Fix potential NULL urb dereference
Revert "usb: gadget: net2280: Add support for PLX USB338X"
USB: usbip: remove CONFIG_USB_DEBUG reference
USB: remove CONFIG_USB_DEBUG from defconfig files
usb: resume child device when port is powered on
usb: hub_handle_remote_wakeup() depends on CONFIG_PM_RUNTIME=y
...
It wasn't even being used for anything, so remove the test for the
config option (as the config option isn't present anymore), and remove
the unused module parameter "debug" so as to not confuse anyone.
Cc: Mauro Carvalho Chehab <m.chehab@samsung.com>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: "Antti Seppälä" <a.seppala@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the dev_dbg dynamic infrastructure instead of rolling our own custom
debug logic. This is needed as CONFIG_USB_DEBUG is now gone.
Cc: Mauro Carvalho Chehab <m.chehab@samsung.com>
Cc: Sean Young <sean@mess.org>
Cc: Hans Verkuil <hans.verkuil@cisco.com>
Cc: Jonathan McCrohan <jmccrohan@gmail.com>
Cc: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The rr3_ftr function duplicates the in-kernel tracing logic, so remove
it.
This is step 1 of of removing the CONFIG_USB_DEBUG depandancy in this
driver.
Cc: Mauro Carvalho Chehab <m.chehab@samsung.com>
Cc: Sean Young <sean@mess.org>
Cc: Hans Verkuil <hans.verkuil@cisco.com>
Cc: Jonathan McCrohan <jmccrohan@gmail.com>
Cc: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some drivers, like au0828 are very sensitive to tuner sleep and may
break if the sleep happens too fast. Also, by keeping the tuner alive
for a while could speedup tuning process during channel scan. So,
change the logic to delay the actual sleep to 5 seconds after its
command.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
WARNING: please, no space before tabs
+#define XC_PRODUCT_ID_FW_LOADED ^I0x1388$
WARNING: please, no space before tabs
+#define DK_SECAM_A2LDK3 ^I13$
WARNING: please, no space before tabs
+#define DK_SECAM_A2MONO ^I14$
WARNING: please, no space before tabs
+#define FM_RADIO_INPUT2 ^I21$
WARNING: please, no space before tabs
+#define FM_RADIO_INPUT1 ^I22$
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
There's absolutely no reason to wrap msleep() call here.
Just rename all occurences of xc_wait() with msleep() and
remove the wrapper function.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
As reported by Trevor, doing several opening/streaming/closing
operations to the demux causes it to fail.
I was able to simulate this bug too. I also noticed that,
sometimes, changing channels with au0828, the same thing
happens.
Most of the issues seem to be due to some hardware bug, that
causes the device to not fill all the URBs allocated. When
the bug happens, the only known fix is to either replug the
device, or to send an USB reset to it.
There's also a hack a the au0828 driver that starts a thread
that tries to reset the device when a package doesn't start
with a sync.
One of the culpits for this bad hardware behavior seem to be
caused by the lack of stopping and restarting the stream every
time a new channel is set.
This patch warrants that the stream will be properly reset
every time the set_frontend callback is called, partially
solving the problem.
A complete fix, however, would also need to check the PM
conditions for the tuner and demux.
Reported-by: Trevor Graffa <tlgraffa@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Sometimes, it helps to know how much data was received by
urb_completion. Add that information to the optional debug
log.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
If the tuner is already disconnected, It is meaningless to go on doing the
stream-restart operation, It is better to cancel this operation.
Signed-off-by: Changbing Xiong <cb.xiong@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The include/media/s5p_fimc.h header has been removed in commit
49b2f4c56f ("exynos4-is: Remove support
for non-dt platforms"). This broke compilation of the m5mols driver.
Include the include/media/exynos-fimc.h header instead, which contains
the S5P_FIMC_TX_END_NOTIFY definition required by the driver.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Change the I/O endpoint handling of the mceusb driver to respect the endpoint
type reported by device (bulk/interrupt), rather than treating all endpoints
as type interrupt, which breaks devices using bulk endpoints when connected
to a xhci controller. Accordingly, change the function calls to initialize
an endpoint's transfer pipe and urb handlers to use the correct function based
on the endpoint type.
[m.chehab@samsung.com: Fix merge conflicts and compilation breakage]
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Tested-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
There is another clone of AZ6027. This patch adds the relevant PID.
Signed-off-by: Manuel Schönlaub <manuel.schoenlaub@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Add an inv_llc_pol field to platform data to control the clock polarity.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The HPD GPIO is used as an output but its direction is never set. Fix
it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Add support for the hsync-active, vsync-active and pclk-sample
properties to the DT bindings and control BT.656 mode implicitly.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Parse the device tree node to populate platform data. Only the ADV7611
is currently support with DT.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
And set input routing when initializing the device.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Add support for optional GPIO-controlled HPD pins in addition to the
ADV7604-specific hotplug notifier.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The *_and_or() functions take an 'and' bitmask to be ANDed with the
register value before ORing it with th 'or' bitmask. As the functions
are used to mask and set bits selectively, this requires the caller to
invert the 'and' bitmask and is thus error prone. Replace those
functions with a *_clr_set() variant that takes a mask of bits to be
cleared instead of a mask of bits to be kept.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This allows replacing duplicate code blocks by loops over the arrays.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This one line function is called in a single location. Inline it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The video enum_dv_timings and dv_timings_cap operations are deprecated
and unused. Remove them.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The video enum_dv_timings and dv_timings_cap operations are deprecated.
Implement the pad-level version of those operations to prepare for the
removal of the video version.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Replace the dummy video format operations by pad format operations that
configure the output format.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Tested-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The ADV7604 has sink pads for its HDMI and analog inputs. Report them.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Control operations are handled by the control framework and the subdev
control handlers are never called directly. Remove them.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This patch adds support for the Analog Devices ADV7611 HDMI receiver.
The adv7611 is quite similar to the adv7604. It has only one instead of four
HDMI inputs and no analog frontend though. Also some register bits have been
shuffled around, but large parts of their register maps are compatible.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
When extracting multiple bits from a single register read the register
once and extract the bits on the read value.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
16-bit registers are read through two 8-bit read operations. Factorize
that common pattern into 16-bit read accessors to simplify the code.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
We do not want to modify the info string arrays ever, so no need to
waste stack space for them. While we are at it also make them const.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Register the device with the v4l2 asynchronous probing framework to
support asynchronous instantiation systems such as DT.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The subdev EDID ioctls receive a pad field that must reference an
existing pad and an EDID field that must point to a buffer. Validate
both fields in the core code instead of duplicating validation in all
drivers.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Validate the pad field in the core code whenever specified.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The video enum_dv_timings and dv_timings_cap operations are deprecated
and unused. Remove them.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The video enum_dv_timings and dv_timings_cap operations are deprecated
and unused. Remove them.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The video enum_dv_timings operation is deprecated and unused. Remove it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The video enum_dv_timings and dv_timings_cap operations are deprecated
and unused. Remove them.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The video enum_dv_timings and dv_timings_cap operations are deprecated
and unused. Remove them.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The video enum_dv_timings and dv_timings_cap operations are deprecated
and unused. Remove them.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The video enum_dv_timings and dv_timings_cap operations are deprecated
and unused. Remove them.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The video-level enum_dv_timings and dv_timings_cap operations are
deprecated in favor of the pad-level versions. All subdev drivers
implement the pad-level versions, switch to them.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The video-level enum_dv_timings and dv_timings_cap operations are
deprecated in favor of the pad-level versions. All subdev drivers
implement the pad-level versions, switch to them.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The video-level enum_dv_timings and dv_timings_cap operations are
deprecated in favor of the pad-level versions. All subdev drivers
implement the pad-level versions, switch to them.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Scott Jiang <scott.jiang.linux@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The video enum_dv_timings operation is deprecated. Implement the
pad-level version of the operation to prepare for the removal of the
video version.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The video enum_dv_timings and dv_timings_cap operations are deprecated.
Implement the pad-level version of those operations to prepare for the
removal of the video version.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The video enum_dv_timings operation is deprecated. Implement the
pad-level version of the operation to prepare for the removal of the
video version.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The video enum_dv_timings and dv_timings_cap operations are deprecated.
Implement the pad-level version of those operations to prepare for the
removal of the video version.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The video enum_dv_timings and dv_timings_cap operations are deprecated.
Implement the pad-level version of those operations to prepare for the
removal of the video version.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The video enum_dv_timings and dv_timings_cap operations are deprecated.
Implement the pad-level version of those operations to prepare for the
removal of the video version.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The video enum_dv_timings and dv_timings_cap operations are deprecated.
Implement the pad-level version of those operations to prepare for the
removal of the video version.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
When suspending a device while a video stream is active all buffers
marked as done but not dequeued yet will be kept across suspend and
given back to userspace after resume. This will result in outdated
buffers being dequeued.
Introduce a new vb2 function to mark all done buffers as erroneous
instead, to be used by drivers at resume time.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
When stopping a video stream the driver waits for ongoing DMA opeations
to complete for the currently active buffer, but doesn't release the
non-active queued buffers. This isn't a problem in most cases as the
video device is usually closed after the stream is stopped, which will
release all the buffers. However the problem would generate a warning
when switching to videobuf2. Fix it by cancelling all buffers after DMA
operations have completed.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This prepares for the move to videobuf2.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This prepares for the move to videobuf2.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This prepares for the move to videobuf2.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The scatterlist is not needed for those buffers, don't build it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Attach an ARM DMA I/O virtual address space to the ISP device. This
switches to the IOMMU-aware ARM DMA backend, we can thus remove the
explicit calls to the OMAP IOMMU map and unmap functions.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Replace the custom implementation with a call to the scatterlist helper
function.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Userspace PFNMAP buffers need to be mapped to the device like the
userspace non-PFNMAP buffers in order for the DMA mapping implementation
to create IOMMU mappings when we'll switch to the IOMMU-aware DMA
mapping backend.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
dma_map_sg() can merge sglist entries, and can thus return a number of
mapped entries different than the original value. Don't consider this as
an error.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
And retrieve the related sg table using dma_get_sgtable().
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The ispmmu_vmap() and ispmmu_vunmap() functions are just wrappers around
omap_iommu_vmap() and omap_iommu_vunmap(). Inline them.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
In preparation for the switch to the DMA API merge the two functions
that handle buffer preparation for the USERPTR cases (both page-backed
and non page-backed memory).
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Replace the sglen and sglist fields stored in the buffer structure with
an sg_table. This allows using the sg table allocation helper function.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
As a preparation for the switch from the OMAP IOMMU API to the DMA API
move all IOMMU handling code from the video node implementation to the
buffers queue implementation.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The v4l buffer bytesused field is a value that will be returned to
userspace when the buffer gets dequeued. As such it doesn't need to be
set early at buffer queue time. Move the assignment to buffer completion
in the omap3isp_video_buffer_next() function to prepare for the video
buffers queue refactoring.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Replace the OMAP-specific IOMMU API usage by the DMA API for FPC. The
table is now allocated using dma_alloc_coherent() and the related sg
table is retrieved using dma_get_sgtable() for sync operations.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Replace the OMAP-specific IOMMU API usage by the DMA API for LSC. The
table is now allocated using dma_alloc_coherent() and the related sg
table is retrieved using dma_get_sgtable() for sync operations.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Replace the OMAP-specific IOMMU API usage by the DMA API. All buffers
are now allocated using dma_alloc_coherent() and the related sg table is
retrieved using dma_get_sgtable() for sync operations.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The driver stores the IOMMU mapped iovm struct pointer in the buffer
structure but only needs the iovm sg table. Store the sg table instead
to prepare the migration to the DMA API.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The fields store buffer addresses as seen from the device. The first one
is used with an external DMA engine while the second one is used with
the ISP DMA engine. As they're never used together, merge them.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Move code common between the isp_stat_bufs_alloc_dma() and
isp_stat_bufs_alloc_iommu() functions to isp_stat_bufs_alloc().
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The WARN_ON statements in the buffer allocation functions try to catch
conditions where buffers would have already been allocated. As the
buffers are explicitly freed right before being allocated this can't
happen.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The macro is meant to test whether the statistics engine uses an
external DMA engine to transfer data or supports DMA directly. As both
cases will be supported by DMA coherent buffers rename the macro to
ISP_STAT_USES_DMAENGINE for improved clarity.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Currently stk1160_read_reg() uses a stack-allocated char to get the
read control value. This is wrong because usb_control_msg() requires
a kmalloc-ed buffer.
This commit fixes such issue by kmalloc'ating a 1-byte buffer to receive
the read value.
While here, let's remove the urb_buf array which was meant for a similar
purpose, but never really used.
Cc: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Sander Eikelenboom <linux@eikelenboom.it>
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: stable@vger.kernel.org # for v3.7 and up
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The g_std and s_std operations are video-related, move them to the video
ops where they belong.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Remove duplicated test of buffer presence at streamon
Signed-off-by: Victor Lambret <victor.lambret.ext@parrot.com>
Acked-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Drops check for #ifdef __KERNEL__, because this header is a Kernel
only header, where this define is always true.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
this patch adds supports to return -ENODATA to *std calls
if the selected output does not support it.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
this patch adds suppport to return -ENODATA for *dv_timings calls
if the current output does not support it.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
this patch uses SIMPLE_DEV_PM_OPS, and drops unneeded members
from io_usrs, usrs and makes use of vb2 helepers instead.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
this patch groups the v4l2_ioctl_ops and align them appropriately.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
this patch drops cropcap as this driver doesnt support cropping.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This patch removes some modprobe parameters, without any reason
or description. I was supposed to not merge this patch, but It
was merged by mistake.
Revert it while nobody provides a good description for such patch.
This reverts commit b952662f27.
Cc: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Cc: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Use the driver-specific inline function to cast from a subdev pointer to
a tvp5150 pointer instead of the generic container_of().
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
When a resolution change point is reached, queue an event to signal the
userspace that a new set of buffers is required before decoding can
continue.
Signed-off-by: Pawel Osciak <posciak@chromium.org>
Signed-off-by: Arun Kumar K <arun.kk@samsung.com>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This event indicates that the video device has encountered
a source parameter change during runtime. This can typically be a
resolution change detected by a video decoder OR a format change
detected by an input connector.
This needs to be nofified to the userspace and the application may
be expected to reallocate buffers before proceeding. The application
can subscribe to events on a specific pad or input port which
it is interested in.
Signed-off-by: Arun Kumar K <arun.kk@samsung.com>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
There is a few conflicts with older symbols on older kernels so we
have to patch this driver when backporting. Instead just make these
routines specific to the driver.
Signed-off-by: Luis R. Rodriguez <mcgrof@suse.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The current names clash with include/linux/leds.h namespace,
although there is no compile issue currently this does affect
backports. Drivers should also try to avoid generic namespaces
for things like this.
Cc: Felipe Pena <felipensp@gmail.com>
Cc: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Luis R. Rodriguez <mcgrof@suse.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
this patch moves the initalization of video device to a
single place and uses macro to define the driver name and
use it appropriately on the required places.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
the started member was indicating whether streaming was started
or not, this can be determined by vb2 offering, this patch replaces
the started member from struct common_obj with appropriate vb2 calls.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This field is set, but not used anymore. Remove it.
No functional changes.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
this patch drops reserving contigiuos memory for the device,
as now with CMA support there is no need of this.
This patch also prepares to removal of config_params.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
this patch adds support to use v4l2_fh_open() and vb2_fop_release,
which allows to drop driver specific struct vpif_fh, as this is handeled
by core. This patch also drops vpif_g/s_priority as this handeled
by core.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
No need to reinvent the wheel. Just use the already existing
functions for that.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
this patch drops unnecessary check from start_streaming() callback
as this is already done in try/s_fmt and some minor code cleanups,
drops check for vb2_is_streaming() as this check is done by vb2
itself before calling this callback.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
this patch sets the sizes[0] of plane according to the fmt passed
or which is being set in the channel, in both MMAP and USERPTR buffer
type.
This patch also move the calculation of offests(vpif_calculate_offsets())
to queue_setup() callback as after queue_setup() callback the
application is no longer allowed to change format, and prepares to
removal of config_params.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
this patch improve vpif_buffer_prepare() callback, as buf_prepare()
callback is never called with invalid state and check for
vb2_plane_vaddr(vb, 0) is dropped as payload check should
be done unconditionally.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
this patch drops buf_cleanup() callback as this callback
is never called with buffer state active.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
this patch adds support to release the buffer by calling
vb2_buffer_done(), with state marked as VB2_BUF_STATE_QUEUED
if start_streaming() call back fails.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
this patch makes use of vb2_ops_wait_prepare/finish helper functions.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
this patch drops the buf_init() callback as init
of buf list is not required.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
this patch moves the initalization of vb2 queue and
the DMA context to probe() and clean up in remove()
callback respectively.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
this patch fixes following checkpatch warning, and alongside
renames the DAVINCIHD_DISPLAY_H to VPIF_DISPLAY_H.
WARNING: Unnecessary space before function pointer arguments
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
this patch adds supports to return -ENODATA to *std calls
if the selected output does not support it.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
this patch adds suppport to return -ENODATA for *dv_timings calls
if the current output does not support it.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
this patch uses SIMPLE_DEV_PM_OPS, and drops unneeded members
from io_usrs, usrs and makes use of vb2 helepers instead.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
this patch gorups the v4l2_ioctl_ops and align them appropriately.
No functional changes.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
this patch drops cropcap as this driver doesnt support cropping.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
this patch moves the initalization of video device to a
single place and uses macro to define the driver name and
use it appropraitely in required places.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
the started member was indicating whether streaming was started
or not, this can be determined by vb2 offering, this patch replaces
the started member from struct common_obj with appropriate vb2 calls.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This patch drops numbuffers member from struct common_obj
as this was not required.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The common->memory field is set but not used anywhere. Drop it.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
this patch drops reserving contigiuos memory for the device,
as now with CMA support there is no need of this.
This patch also prepares to removal of config_params.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
As fbuffers is not used anymore, remove it.
No functional changes.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
this patch adds support to use v4l2_fh_open() and vb2_fop_release,
which allows to drop driver specific struct vpif_fh, as this is handeled
by core. This patch also drops vpif_g/s_priority as this handeled
by core.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
No need to reinvent the wheel. Just use the already existing
functions for that.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
this patch drops unnecessary check from start_streaming() callback
as this is already done in try/s_fmt and some minor code cleanups,
drops check for vb2_is_streaming() as this check is done by vb2
itself before calling this callback.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
this patch sets the sizes[0] of plane according to the fmt passed
or which is being set in the channel, in both MMAP and USERPTR buffer
type.
This patch also move the calculation of offests(vpif_calculate_offsets())
to queue_setup() callback as after queue_setup() callback the
application is no longer allowed to change format, and prepares to
removal of config_params.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
this patch improve vpif_buffer_prepare() callback, as buf_prepare()
callback is never called with invalid state and check for
vb2_plane_vaddr(vb, 0) is dropped as payload check should
be done unconditionally.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
this patch drops buf_cleanup() callback as this callback
is never called with buffer state active.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
this patch adds support to release the buffer by calling
vb2_buffer_done(), with state marked as VB2_BUF_STATE_QUEUED
if start_streaming() call back fails.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
this patch makes use of vb2_ops_wait_prepare/finish helper functions.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
this patch drops the buf_init() callback as init
of buf list is not required.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
this patch moves the initalization of vb2 queue and
the DMA context to probe() and clean up in remove()
callback respectively.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
All platforms supported by this driver are going to get device tree
support in this kernel release so remove code that would have been
actually not used any more.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Ensure dma_free_coherent() is not called with incorrect arguments
and only when the memory was actually allocated. This will prevent
possible crashes on error paths of the top level media device driver,
when fimc-is device gets unregistered and its driver detached.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: stable@vger.kernel.org # for v3.15
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
CONFIG_COMMON_CLK is not enabled on S5PV210 platform, so include
some clk API data structures conditionally to avoid compilation
errors. These #ifdefs will be removed for next kernel release,
when the S5PV210 platform moves to DT and the common clk API.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: stable@vger.kernel.org # for 3.15
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This patch adds core support for v8 encoder. This
patch also adds register definitions and buffer size
requirements for H264 & VP8 encoding, needed for new
firmware version v8 for MFC
Signed-off-by: Kiran AVND <avnd.kiran@samsung.com>
Signed-off-by: Pawel Osciak <posciak@chromium.org>
Signed-off-by: Arun Kumar K <arun.kk@samsung.com>
[k.debski@samsung.com: Change MFC version macro name to MFC_V8_BIT]
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This patch adds variant data and core support for
V8 decoder. This patch also adds the register definition
file for new firmware version v8 for MFC.
Signed-off-by: Kiran AVND <avnd.kiran@samsung.com>
Signed-off-by: Pawel Osciak <posciak@chromium.org>
Signed-off-by: Arun Kumar K <arun.kk@samsung.com>
[k.debski@samsung.com: Change MFC version macro name to MFC_V8_BIT]
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
MFC versions support a different set of formats, this specially applies
to the raw YUV formats. This patch changes enum_fmt, so that it only
reports formats that are supported by the used MFC version.
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The patch adding the v6 version of MFC changed the default format for
the CAPTURE queue, but this also affects the v5 version. This patch
solves this problem by checking the MFC version before assigning the
default format.
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Renaming the IS_MFCV7 macro to IS_MFCV7_PLUS for the
addition of MFCv8 support which reuses the v7 code.
Signed-off-by: Arun Kumar K <arun.kk@samsung.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This patch is needed in preparation to add MFC V8
where the register offsets are changed w.r.t MFC V6/V7.
This patch adds variants of MFC V6 and V7 while
accessing MFC registers. Registers are kept in mfc context
and are initialized to a particular MFC variant during probe,
which is used instead of macros.
This avoids duplication of the code for MFC variants
V6 & V7, and reduces the if_else checks while accessing
registers of different MFC variants.
Signed-off-by: Kiran AVND <avnd.kiran@samsung.com>
Signed-off-by: Pawel Osciak <posciak@chromium.org>
Signed-off-by: Arun Kumar K <arun.kk@samsung.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The register S5P_FIMV_D_INIT_BUFFER_OPTIONS holds good for v6
firmware too. So moving the definition from v7 regs to v6.
Signed-off-by: Arun Kumar K <arun.kk@samsung.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Update the MPEG4 decoder scratch buffer size as per the
new v6 firmware. This updation is increasing the size and so
is backward compatible with older v6 firmwares.
Signed-off-by: Arun Kumar K <arun.kk@samsung.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Currently, for formats that are not H264, MFC driver will check
the consumed stream size returned by the firmware and, based on that,
will try to decide whether the bitstream buffer contained more than
one frame. If the size of the buffer is larger than the consumed
stream, it assumes that there are more frames in the buffer and that the
buffer should be resubmitted for decode. This rarely works though and
actually introduces problems, because:
- v7 firmware will always return consumed stream size equal to whatever
the driver passed to it when running decode (which is the size of the whole
buffer), which means we will never try to resubmit, because the firmware
will always tell us that it consumed all the data we passed to it;
- v6 firmware will return the number of consumed bytes, but will not
include the padding ("stuffing") bytes that are allowed after the frame
in VP8. Since there is no way of figuring out how many of those bytes
follow the frame without getting the frame size from IVF headers (or
somewhere else, but not from the stream itself), the driver tries to guess that
padding size is not larger than 4 bytes, which is not always true;
The only way to make it work is to queue only one frame per buffer from
userspace and the check in the kernel is useless and wrong for VP8.
So adding VP8 also along with H264 to disallow re-submitting of buffer
back to hardware for decode.
Signed-off-by: Pawel Osciak <posciak@chromium.org>
Signed-off-by: Arun Kumar K <arun.kk@samsung.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Scratch buffer size updated for vp8 encoding as per
the latest v7 firmware. As the new macro increases the
scratch buffer size, it is backward compatible with the older
firmware too.
Signed-off-by: Kiran AVND <avnd.kiran@samsung.com>
Signed-off-by: Arun Kumar K <arun.kk@samsung.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Currently, we allocate private codec buffers on STREAMON, which may fail
if we are out of memory. We don't check for failure though, which will
make us crash with the codec accessing random memory.
We shouldn't be failing STREAMON with out of memory errors though. So move
the allocation of private codec buffers to REQBUFS for OUTPUT queue. Also,
move MFC instance opening and closing to REQBUFS as well, as it's tied to
allocation and deallocation of private codec buffers.
Signed-off-by: Pawel Osciak <posciak@chromium.org>
Signed-off-by: Arun Kumar K <arun.kk@samsung.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This is in preparation for a new flow to fix issues with streamon, which
should not be allocating buffer memory.
Signed-off-by: Pawel Osciak <posciak@chromium.org>
Signed-off-by: Arun Kumar K <arun.kk@samsung.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
- Honor return values from vb2_reqbufs on REQBUFS(0).
- Do not set the number of allocated buffers to 0 if userspace tries
to request buffers again without freeing them.
- There is no need to verify correct instance state on reqbufs, as we will
verify this in queue_setup().
- There is also no need to verify that vb2_reqbufs() was able to allocate enough
buffers (pb_count) and call buf_init on that many buffers (i.e. dst_buf_count
is at least pb_count), because this will be verified by second queue_setup()
call as well and vb2_reqbufs() will fail otherwise.
- Only verify state is MFCINST_INIT when allocating, not when freeing.
- Refactor and simplify code.
Signed-off-by: Pawel Osciak <posciak@chromium.org>
Signed-off-by: Arun Kumar K <arun.kk@samsung.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Timestamps for destination buffers are assigned by copying them from
corresponding source buffers when the decode operation results in a frame
being outputted to a destination buffer. But the decision when to do this, i.e.
whether the decode operation on current source buffer produced a destination
frame, is wrongly based on "display status". Display status reflects the status
of the destination buffer, not source.
This used to work for firmwares version <= 6, because in addition to the above,
we'd check the decoded frame type register, which was set to "skipped" if
a destination frame was not produced, exiting early from
s5p_mfc_handle_frame_new().
Firmware >=7 does not set the frame type register for frames that were not
decoded anymore though, which results in us wrongly overwriting timestamps of
previously decoded buffers (firmware reports the same destination buffer address
as previously decoded one if a frame wasn't decoded during current operation).
To do it properly, we should be basing our decision to copy the timestamp on the
status of the source buffer, i.e. "decode status". The decode status register
values are confusing, because in its case "display" means "a frame has been
outputted to a destination buffer". We should copy if "decode and display"
is returned in it. This also works on <= v6 firmware, which behaves in the same
way with regards to decode status register.
Signed-off-by: Pawel Osciak <posciak@chromium.org>
Signed-off-by: Arun Kumar K <arun.kk@samsung.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This patch adds the missing mutex_destroy(), when the driver is removed.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
There are no need to store resource struct and IRQ in the driver
internal structure.
This patch remove these fields and improve error handling by using
proper return codes from devm_ioremap_resource() and devm_request_irq().
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
VIDIOC_STREAMOFF clears the encoder's destination queue -- routines run
from the interrupt handler cannot assume that the queue is non-empty.
Signed-off-by: John Sheu <sheu@google.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Auto BLC and BLC digital offset are disabled when enabling the test
pattern and must be restored when disabling it. The driver does so by
calling the set control handler on the auto BLC and BLC offset controls,
but this programs the hardware with the new value of those controls, not
the current value. Fix this by writing to the registers directly.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The digital side of the Black Level Calibration (BLC) function must be
disabled when generating a test pattern to avoid artifacts in the image.
The driver disables BLC correctly at the hardware level, but the feature
gets reenabled by v4l2_ctrl_handler_setup() the next time the device is
powered on.
Fix this by marking the BLC controls as inactive when generating a test
pattern, and ignoring control set requests on inactive controls.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Rename the memory block resource "vpe_csc" to "csc" since it also exists within
the VIP IP block. This would make the name more generic, and both VPE and VIP DT
nodes in the future can use it.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Add selection ioctl ops. For VPE, cropping makes sense only for the input to
VPE(or V4L2_BUF_TYPE_VIDEO_OUTPUT/MPLANE buffers) and composing makes sense
only for the output of VPE(or V4L2_BUF_TYPE_VIDEO_CAPTURE/MPLANE buffers).
For the CAPTURE type, V4L2_SEL_TGT_COMPOSE results in VPE writing the output
in a rectangle within the capture buffer. For the OUTPUT type, V4L2_SEL_TGT_CROP
results in selecting a rectangle region within the source buffer.
Setting the crop/compose rectangles should successfully result in
re-configuration of registers which are affected when either source or
destination dimensions change, set_srcdst_params() is called for this purpose.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Some parameters of the VPE descriptors were understood incorrectly. They are now
fixed. The fixes are explained as follows:
- When adding an inbound data descriptor to the VPDMA descriptor list, we intend
to use c_rect as the cropped region fetched by VPDMA. Therefore, c_rect->width
shouldn't be used to calculate the line stride, the original image width
should be used for that. We add a 'width' argument which gives the buffer
width in memory.
- frame_width and frame_height describe the complete width and height of the
client to which the channel is connected. If there are multiple channels
fetching data and providing to the same client, the above 2 arguments should
be the width and height of the region covered by all the channels. In the case
where there is only one channel providing pixel data to the client
(like in VPE), frame_width and frame_height should be the cropped width and
cropped height respectively. The calculation of these params is done in the
vpe driver now.
- start_h and start_v is also used in the case of multiple channels to describe
where each channel should start filling pixel data. We don't use this in VPE,
and pass 0s to the vpdma_add_in_dtd() helper.
- Some minor changes are made to the vpdma_add_out_dtd() helper. The c_rect
param is used for specifying the 'composition' target, and 'width' is added
to calculate the line stride.
Signed-off-by: Archit Taneja <archit@ti.com>
Acked-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
For OMAP and DRA7x, we generally allocate video and graphics buffers through
omapdrm since the corresponding omap-gem driver provides DMM-Tiler backed
contiguous buffers. omapdrm is a dma-buf exporter. These buffers are used by
other drivers in the video pipeline.
Add VB2_DMABUF flag to the io_modes of the vb2 output and capture queues. This
allows the driver to import dma shared buffers.
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
vpe fops(vpe_open in particular) should be called only when VPDMA firmware
is loaded. File operations on the video device are possible the moment it is
registered.
Currently, we register the video device for VPE at driver probe, after calling
a vpdma helper to initialize VPDMA and load firmware. This function is
non-blocking(it calls request_firmware_nowait()), and doesn't ensure that the
firmware is actually loaded when it returns.
We remove the device registration from vpe probe, and move it to a callback
provided by the vpe driver to the vpdma library, through vpdma_create().
The ready field in vpdma_data is no longer needed since we always have firmware
loaded before the device is registered.
A minor problem with this approach is that if the video_register_device
fails(which doesn't really happen), the vpe platform device would be registered.
however, there won't be any v4l2 device corresponding to it.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
If the saa7134 module is loaded with the saa7134_userptr set to 1,
then USERPTR support is enabled. A check in buffer_prepare
verifies that the pointer is page-aligned.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Convert the saa7134 driver to vb2.
Note that while this uses the vb2-dma-sg version, the VB2_USERPTR mode is
disabled. The DMA hardware only supports DMAing full pages, and in the
USERPTR memory model the first and last scatter-gather buffer is almost
never a full page.
In practice this means that we can't use the VB2_USERPTR mode.
This has been tested with raw video, compressed video, VBI, radio, DVB and
video overlays.
Unfortunately, a vb2 conversion is one of those things you cannot split
up in smaller patches, it's all or nothing. This patch switches the whole
driver over to vb2, using the vb2 ioctl and fop helper functions.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
All dmaqueue's use saa7134_pgtable, so move it into struct saa7134_dmaqueue.
The videobuf_queue priv_data field now points to the dmaqueue struct.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
num_buffers can't be bigger than VIDEO_MAX_FRAME. This is assured by:
num_buffers = min_t(unsigned int, req->count, VIDEO_MAX_FRAME);
However, this value is overriden by:
num_buffers = max_t(unsigned int, req->count, q->min_buffers_needed);
It should, instead, use the previously calculated value as an input
to max_t:
num_buffers = max_t(unsigned int, num_buffers, q->min_buffers_needed);
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The __vb2_queue_cancel function marks the queue as not streaming and
then WARNs when buffers are still owned by the driver. It proceeds to
complete all active buffers by calling vb2_buffer_done with the new
buffer state set to VB2_BUF_STATE_ERROR in that case. This triggers
another WARN_ON due to as new state not being VB2_BUF_STATE_QUEUED while
the queue is not streaming.
Check buffer ownership and complete all active buffers before marking
the queue as not streaming to avoid the double WARN_on.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Both wq_trigger and stream_started are used only to control the em28xx
alsa streaming. They don't belong to em28xx common struct.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The tuner address is only used by the v4l submodule and at tuner setup and
can be obtained from the board data directly (if specified).
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The tda9887 chipset is part of the analog tuner. Move it out of
em28xx-cards.
Also, it is used only one time by the v4l2 sub-module at tuner setup.
With that, we can get rid of an additional data inside the em28xx
common structure.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Move V4L2-specific frequency cache to struct em28xx_v4l2.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Despite being at the common em28xx struct, those two fields are
actually taking into account only the usage inside em28xx v4l2
submodule. So, move them out of the common struct.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Move some temporary capture tracking date to the em28xx_v4l2 struct,
as those info are used only by em28xx v4l2 submodule.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Move camera sensor resolution and xtal out of em28xx common struct,
as thore are used only by the em28xx v4l2 submodule.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The video progressive data fields belong to analog TV. Move them out
of the common em28xx struct.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The analog format struct belongs to analog TV. Move it out of the
common em28xx struct.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
TV norm is specific to analog TV reception. move it out of the common
em28xx struct.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The video input mode and control data also belong only to the
analog side. move them to struct em28xx_v4l.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The em28xx scaler data are used only for analog video. Move them to
struct em28xx_v4l2.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The video and VBI-specific VB2 queue and mutexes are used only by
the v4l2 sub-driver. Move them to the V4L2 struct, preventing
wasting memory if this sub-driver is not used.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
There are 3 struct video_device at the em28xx common struct,
for video, VBI and radio. They all are used only by the V4L2 driver.
So, move them to the v4l2-specific struct.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The current clock definition applies only to the V4L2 side of the
driver. Move its struct pointer to the v4l2_dev, where it belongs.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Controls are only applicable to V4L2 module. Move the corresponding
data structs to the proper place.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
That reduces a little bit the memory footprint when em28xx-video
is not loaded.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The local var hdl is already pointing to &dev->ctrl_handler.
Use it, instead of dereferencing it all the time.
Code cleanup. No functional changes.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Just a cleanup. No functional changes.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
It is no longer needed since nobody is calling i2c_get_adapdata() anymore.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The message logged by v4l_print_cropcap should be a single line withouti
linebreaks, just like all the other v4l_print_<ioctl> functions.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The second argument should be physical address rather than virtual address.
Signed-off-by: Ma Haijun <mahaijuns@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
When ivtv PCM device is accessed at the state where no firmware is
loaded, it oopses like:
BUG: unable to handle kernel NULL pointer dereference at 0000000000000050
IP: [<ffffffffa049a881>] try_mailbox.isra.0+0x11/0x50 [ivtv]
Call Trace:
[<ffffffffa049aa20>] ivtv_api_call+0x160/0x6b0 [ivtv]
[<ffffffffa049af86>] ivtv_api+0x16/0x40 [ivtv]
[<ffffffffa049b10c>] ivtv_vapi+0xac/0xc0 [ivtv]
[<ffffffffa049d40d>] ivtv_start_v4l2_encode_stream+0x19d/0x630 [ivtv]
[<ffffffffa0530653>] snd_ivtv_pcm_capture_open+0x173/0x1c0 [ivtv_alsa]
[<ffffffffa04526f1>] snd_pcm_open_substream+0x51/0x100 [snd_pcm]
[<ffffffffa0452853>] snd_pcm_open+0xb3/0x260 [snd_pcm]
[<ffffffffa0452a37>] snd_pcm_capture_open+0x37/0x50 [snd_pcm]
[<ffffffffa033f557>] snd_open+0xa7/0x1e0 [snd]
[<ffffffff8118a628>] chrdev_open+0x88/0x1d0
[<ffffffff811840be>] do_dentry_open+0x1de/0x270
[<ffffffff81193a73>] do_last+0x1c3/0xec0
[<ffffffff81194826>] path_openat+0xb6/0x670
[<ffffffff81195b65>] do_filp_open+0x35/0x80
[<ffffffff81185449>] do_sys_open+0x129/0x210
[<ffffffff815b782d>] system_call_fastpath+0x1a/0x1f
This patch adds the check of firmware at PCM open callback like other
open callbacks of this driver.
Bugzilla: https://apibugzilla.novell.com/show_bug.cgi?id=875440
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This will help to debug driver, allows us to see the full name of
the device through /proc/interrupts.
CPU0
...
69: 0 mxc-avic 53 10023000.coda
...
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
this patch adds support to release the buffer by calling
vb2_buffer_done(), with state marked as VB2_BUF_STATE_QUEUED
if start_streaming() call back fails.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This patch moves data allocated using kzalloc to managed data allocated
using devm_kzalloc and cleans now unnecessary kfrees in probe and remove
functions.The label err_register is removed as it is no longer required.
The following Coccinelle semantic patch was used for making the change:
@platform@
identifier p, probefn, removefn;
@@
struct platform_driver p = {
.probe = probefn,
.remove = removefn,
};
@prb@
identifier platform.probefn, pdev;
expression e, e1, e2;
@@
probefn(struct platform_device *pdev, ...) {
<+...
- e = kzalloc(e1, e2)
+ e = devm_kzalloc(&pdev->dev, e1, e2)
...
?-kfree(e);
...+>
}
@rem depends on prb@
identifier platform.removefn;
expression e;
@@
removefn(...) {
<...
- kfree(e);
...>
}
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Function del_timer() does not guarantee that timer was really deleted.
If the timer handler is beeing executed at the moment, the function
does nothing. So, we have a race between del_timer() and kfree(), and
it's possible to use already freed memory in the handler.
Signed-off-by: Kirill Tkhai <tkhai@yandex.ru>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The else statement here is not aligned with the correct if statement.
I think the code works as intended and it's just the indenting which is
wrong. Also kernel style says we should use curly braces here so I have
added those.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
devm_ioremap_resource() returns a pointer to the remapped memory or
an ERR_PTR() encoded error code on failure. Fix the checks inside
csc_create() and sc_create() accordingly.
Cc: Archit Taneja <archit@ti.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Tested-by: Archit Taneja<archit@ti.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
em28xx_compression_disable() is a single line function which is called only one
time and this call also isn't needed.
Register 0x26 is always configured as part of the scaler configuration, which
in turn is always done when the resolution changes. And the initial resolution
setting is applied at first device open.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Just driver cleanup. No functional changes.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Prepare for supporting systems using the Device tree. Should the resources
not be available at the time of driver probe(), the EPROBE_DEFER error code
must be also returned from its probe function.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Do not use our special value, SMIAPP_NO_XSHUTDOWN.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The "best" value was unsigned however, leading to signed-to-unsigned
comparison and wrong results. Possibly only on a newer GCC. Fix this by
making the best value signed as well.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Some of the limits are used before the limits quirk is called. Move the call
immediately after obtaining the limits.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
timestamps in v4l2 buffers returned to userspace are updated in
uvc_video_clock_update() which uses timestamps fetched from
uvc_video_clock_decode() by calling unconditionally ktime_get_ts().
Hence setting the module clock param to realtime has no effect before
this patch.
This has been tested with ffmpeg:
ffmpeg -y -f v4l2 -input_format yuyv422 -video_size 640x480 -framerate 30 -i /dev/video0 \
-f alsa -acodec pcm_s16le -ar 16000 -ac 1 -i default \
-c:v libx264 -preset ultrafast \
-c:a libfdk_aac \
out.mkv
and inspecting the v4l2 input starting timestamp.
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: Olivier Langlois <olivier@trillion01.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Set error bit for incomplete buffers when end of buffer is detected by
FID toggling (for example when last transaction with EOF is lost).
This prevents passing incomplete buffers to the userspace.
Signed-off-by: Anton Leontiev <bunder@t-25.ru>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJTfR2zAAoJEHm+PkMAQRiG3noH/2s+KUge3qO2M+AmxttUo74B
+npAMdbqYR3MdEiwxYZfsHcMu4Ye/IKLcrh4pydB5hI2mdjtGkH1bnmia0f1ve/c
Z/a0256+W8gWp7mcUBqSNztqLPAWa7wKOqNdLjj5idr1BSj6u8im+fQ9FBh2woki
1fyYAuq/60lq4CMOKJvkA95V1Ome/jO+8tS4PguOgsCETQxCVFGurZcBbG3Mx5Y3
v+ioCqeRc6GvxPFR6YngnTZCrsLxSRT3tnO2Qy5zX7dxjIQkCEbvIckpBQv01Y3R
wNUaX+2Jae207igxrEv8CjmCFnmZFuUI15aWWCy6fOS/j8bjuk6ThYJO8N4ZBM0=
=2ShG
-----END PGP SIGNATURE-----
Merge tag 'v3.15-rc6' into patchwork
Linux 3.15-rc6
* tag 'v3.15-rc6': (1314 commits)
Linux 3.15-rc6
Btrfs: send, fix incorrect ref access when using extrefs
Btrfs: fix EIO on reading file after ioctl clone works on it
scripts/checksyscalls.sh: Make renameat optional
asm-generic: Add renameat2 syscall
ia64: add renameat2 syscall
parisc: add renameat2 syscall
m68k: add renameat2 syscall
sysfs: make sure read buffer is zeroed
ahci: imx: PLL clock needs 100us to settle down
PCI: Wrong register used to check pending traffic
target: fix memory leak on XCOPY
random: fix BUG_ON caused by accounting simplification
clk: tegra: Fix wrong value written to PLLE_AUX
staging: rtl8723au: Do not reset wdev->iftype in netdev_close()
ACPI / video: Revert native brightness quirk for ThinkPad T530
staging: rtl8723au: Use correct pipe type for USB interrupts
crush: decode and initialize chooseleaf_vary_r
libceph: fix corruption when using page_count 0 page in rbd
arm64: fix pud_huge() for 2-level pagetables
...
Pull media fixes from Mauro Carvalho Chehab:
"Most of the changes are drivers fixes (rtl28xuu, fc2580, ov7670,
davinci, gspca, s5p-fimc and s5c73m3).
There is also a compat32 fix and one infoleak fixup at the media
controller"
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
[media] V4L2: fix VIDIOC_CREATE_BUFS in 64- / 32-bit compatibility mode
[media] V4L2: ov7670: fix a wrong index, potentially Oopsing the kernel from user-space
[media] media-device: fix infoleak in ioctl media_enum_entities()
[media] fc2580: fix tuning failure on 32-bit arch
[media] Prefer gspca_sonixb over sn9c102 for all devices
[media] media: davinci: vpfe: make sure all the buffers unmapped and released
[media] staging: media: davinci: vpfe: make sure all the buffers are released
[media] media: davinci: vpbe_display: fix releasing of active buffers
[media] media: davinci: vpif_display: fix releasing of active buffers
[media] media: davinci: vpif_capture: fix releasing of active buffers
[media] s5p-fimc: Fix YUV422P depth
[media] s5c73m3: Add missing rename of v4l2_of_get_next_endpoint() function
[media] rtl28xxu: silence error log about disabled rtl2832_sdr module
[media] rtl28xxu: do not hard depend on staging SDR module
Changeset 15e64f0dde broke compilation on several archs, as it
forgot to include vmalloc.h.
drivers/media/pci/saa7134/saa7134-alsa.c: In function ‘saa7134_alsa_dma_init’:
CC [M] drivers/media/rc/keymaps/rc-behold-columbus.o
drivers/media/pci/saa7134/saa7134-alsa.c:283:2: error: implicit declaration of function ‘vmalloc_32’ [-Werror=implicit-function-declaration]
dma->vaddr = vmalloc_32(nr_pages << PAGE_SHIFT);
^
drivers/media/pci/saa7134/saa7134-alsa.c:283:13: warning: assignment makes pointer from integer without a cast [enabled by default]
dma->vaddr = vmalloc_32(nr_pages << PAGE_SHIFT);
^
drivers/media/pci/saa7134/saa7134-alsa.c:296:2: error: implicit declaration of function ‘vzalloc’ [-Werror=implicit-function-declaration]
dma->sglist = vzalloc(dma->nr_pages * sizeof(*dma->sglist));
^
drivers/media/pci/saa7134/saa7134-alsa.c:296:14: warning: assignment makes pointer from integer without a cast [enabled by default]
dma->sglist = vzalloc(dma->nr_pages * sizeof(*dma->sglist));
^
drivers/media/pci/saa7134/saa7134-alsa.c:310:2: error: implicit declaration of function ‘vfree’ [-Werror=implicit-function-declaration]
vfree(dma->sglist);
Add it to avoid such breakages.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Add USB ID for Peak DVB-T USB.
[crope@iki.fi: fix Brian email address and indentation]
Signed-off-by: Brian Healy <healybrian@gmail.com>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Cc: stable@vger.kernel.org
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
S5PC210 SoC doesn't support encoding NV12 raw images. Remove
relavant flag from the respective entry in the sjpeg_formats
array.
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This patch fixes build break occurring when there is no support
for Device Tree turned on in the kernel configuration. In such
case only the driver variant for S5PC210 SoC will be available.
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Prevent decompression of a JPEG 4:2:0 with odd width to
the YUV 4:2:0 compliant formats for Exynos4x12 SoCs and
adjust capture format to RGB565 in such a case. This is
required because the configuration would produce a raw
image with broken luma component.
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This patch fixes jpeg sysmmu page fault on Exynos4x12 SoCs.
During encoding Exynos4x12 SoCs access wider memory area
than it results from Image_x and Image_y values written to
the JPEG_IMAGE_SIZE register. In order to avoid sysmmu page
fault apply proper output buffer size alignment.
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Remove erroneous guard preventing successful execution of
g_selection callback in case the driver variant is different
from SJPEG_S5P.
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Simplify the code by adding m2m_ops field to the
s5p_jpeg_variant structure which allows to avoid
"if" statement in the s5p_jpeg_probe function.
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Change the driver variant check from "is not S5PC210"
to "is Exynos4" while checking whether YUV format needs
to be downgraded in order to prevent upsampling which
is not supported by Exynos4 SoCs family.
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Simplify the code by adding fmt_ver_flag field
to the s5p_jpeg_variant structure which allows
to avoid "if" statement in the s5p_jpeg_find_format
function.
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This formula did not take into account the required tiled alignement for
NV12MT format. As this was already computed an stored in payload array
initially, reuse that value.
Signed-off-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Testing showed that HW produces BGR32 rather then RGB32 as exposed
in the driver. The documentation seems to state the pixels are stored
in little endian order.
Signed-off-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
[s.nawrocki@samsung.com] replaced "BGRB888, 32 bpp" with "BGRA8888, 32 bpp"
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Depth and payload is defined per memory plane. It's better to iterate using
number of memory planes. This was not causing much issue since the rest
of the arrays involved where intialized to zero.
Signed-off-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
If a struct contains 64-bit fields, it is aligned on 64-bit boundaries
within containing structs in 64-bit compilations. This is the case with
struct v4l2_window, which contains pointers and is embedded into struct
v4l2_format, and that one is embedded into struct v4l2_create_buffers.
Unlike some other structs, used as a part of the kernel ABI as ioctl()
arguments, that are packed, these structs aren't packed. This isn't a
problem per se, but the ioctl-compat code for VIDIOC_CREATE_BUFS contains
a bug, that triggers in such 64-bit builds. That code wrongly assumes,
that in struct v4l2_create_buffers, struct v4l2_format immediately follows
the __u32 memory field, which in fact isn't the case. This bug wasn't
visible until now, because until recently hardly any applications used
this ioctl() and mostly embedded 32-bit only drivers implemented it. This
is changing now with addition of this ioctl() to some USB drivers, e.g.
UVC. This patch fixes the bug by copying parts of struct
v4l2_create_buffers separately.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Cc: stable@vger.kernel.org
Commit 75e2bdad89 "ov7670: allow
configuration of image size, clock speed, and I/O method" uses a wrong
index to iterate an array. Apart from being wrong, it also uses an
unchecked value from user-space, which can cause access to unmapped
memory in the kernel, triggered by a normal desktop user with rights to
use V4L2 devices.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Jonathan Corbet <corbet@lwn.net>
Cc: stable@vger.kernel.org
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
If a struct contains 64-bit fields, it is aligned on 64-bit boundaries
within containing structs in 64-bit compilations. This is the case with
struct v4l2_window, which contains pointers and is embedded into struct
v4l2_format, and that one is embedded into struct v4l2_create_buffers.
Unlike some other structs, used as a part of the kernel ABI as ioctl()
arguments, that are packed, these structs aren't packed. This isn't a
problem per se, but the ioctl-compat code for VIDIOC_CREATE_BUFS contains
a bug, that triggers in such 64-bit builds. That code wrongly assumes,
that in struct v4l2_create_buffers, struct v4l2_format immediately follows
the __u32 memory field, which in fact isn't the case. This bug wasn't
visible until now, because until recently hardly any applications used
this ioctl() and mostly embedded 32-bit only drivers implemented it. This
is changing now with addition of this ioctl() to some USB drivers, e.g.
UVC. This patch fixes the bug by copying parts of struct
v4l2_create_buffers separately.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Commit 75e2bdad89 "ov7670: allow
configuration of image size, clock speed, and I/O method" uses a wrong
index to iterate an array. Apart from being wrong, it also uses an
unchecked value from user-space, which can cause access to unmapped
memory in the kernel, triggered by a normal desktop user with rights to
use V4L2 devices.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Jonathan Corbet <corbet@lwn.net>
Cc: stable@vger.kernel.org
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
If the sub-device did not report any tvnorms, then disable the STD
ioctls.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski+renesas@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
When the sub-device is registered, increment the use count of the sub-device
owner only if it's different from the owner of the driver for the media
device. This avoids increasing the use count by the module itself and thus
making it possible to unload it when it's not in use.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
mdev->fops->owner is actually the owner of the very same module which
implements media_device_register(), so it can't be unloaded anyway. Instead,
use THIS_MODULE through a macro as does video_register_device().
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
VIDIOC_SUBDEV_[GS]_FRAME_INTERVAL IOCTLs argument structs contain the pad
field but the validity check was missing. There should be no implications
security-wise from this since no driver currently uses the pad field in the
struct.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This is already available from saa7134_dev.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Don't calculate this for every buffer, store it globally instead.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This will make the next patch a bit easier to read.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
saa7134-alsa used low-level videobuf functions to allocate and sync
DMA buffers. Replace this with saa7134-specific code. These functions
will not be available when we convert to vb2.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Just white space and coding style changes to reduce the noise in the
following patches.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This solves this bug:
https://bugzilla.kernel.org/show_bug.cgi?id=73361
The problem is that when you quit tvtime it calls STREAMOFF, but then it queues a
bunch of buffers for no good reason before closing the file descriptor.
In the past closing the fd would free the vb queue since that was part of the file
handle struct. Since that was moved to the global struct that no longer happened.
This wouldn't be a problem, but the extra QBUF calls that tvtime does meant that
the buffer list in videobuf (q->stream) contained buffers, so REQBUFS would fail
with -EBUSY.
The solution is to init the list head explicitly when releasing the file
descriptor and to not free the video resource when calling streamoff.
The real fix will hopefully go into kernel 3.16 when the vb2 conversion is
merged. Basically the saa7134 driver with the old videobuf is so full of holes it
ain't funny anymore, so consider this a band-aid for kernels 3.14 and 15.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: stable@vger.kernel.org # for v3.14 and up
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The register address, width and flags are encoded as a 32-bit value. Add
macros for obtaining these separately. Use the macros in register access
functions.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Add a quirk for diverting registers for on some sensors, even the standard
registers are not where they can be expected to be found. Add a quirk to
to help using such sensors.
smiapp_write_no_quirk() and smiapp_read_no_quirk() functions are provided
for the use of quirk implementations.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This is more flexible. Quirk flags may be affected by configuration.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
No reason to keep this u8, really.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
It doesn't make sense to just copy the information to the PLL flags. Add a
new fields for the quirks to contain the PLL flags.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The sub-device names should be unique. Should two identical sensors be
present in the same media device they would be indistinguishable. The names
will change e.g. from "vs6555 pixel array" to "vs6555 1-0010 pixel array".
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
8-bit reads are needed in some cases; however the condition used was wrong.
Regular access (register width) was used if:
len == SMIAPP_REG_8BIT && !only8
This causes 8-bit read access to be used always. The operator should be ||
instead: regular access can be used for 8-bit reads OR if allowed otherwise.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
SMIAPP_REG_ is the common prefix used in the driver for register related
definitions. Use it consistently.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The quirk registers mechanism which allows register to have a static read
access value from the sensor specific quirks, is not used. Remove it. It is
to be replaced by a more generic register diversion quirk soon.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Implement support for the VSP1 DT bindings in the VSP1 driver. The
driver now first retrieves platform data either from the platform data
pointer or by reading the device tree node, and then validates it
regardless of the platform data source.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The Blend ROP Unit performs blending and ROP operations for up to four
sources.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Scaling of the alpha layer is disabled as both the RPF and WPF are
configured to hardcode the alpha value to 255. This results in a 0 alpha
value at the UDS output, making the image invisible when alpha blended
in the BRU. Fix it by enabling scaling of the alpha layer.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The VSP1 has no rt clock. Remove them from the driver.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
When compiling this for older kernels using the compatibility build
the compiler complains about uninitialized variables:
In file included from include/linux/kernel.h:20:0,
from include/linux/cache.h:4,
from include/linux/time.h:7,
from include/linux/input.h:13,
from /home/hans/work/build/media_build/v4l/compat.h:9,
from <command-line>:0:
/home/hans/work/build/media_build/v4l/videobuf2-core.c: In function 'vb2_mmap':
include/linux/dynamic_debug.h:60:9: warning: 'plane' may be used uninitialized in this function [-Wmaybe-uninitialized]
printk(KERN_DEBUG pr_fmt(fmt), ##__VA_ARGS__); \
^
/home/hans/work/build/media_build/v4l/videobuf2-core.c:2381:23: note: 'plane' was declared here
unsigned int buffer, plane;
^
In file included from include/linux/kernel.h:20:0,
from include/linux/cache.h:4,
from include/linux/time.h:7,
from include/linux/input.h:13,
from /home/hans/work/build/media_build/v4l/compat.h:9,
from <command-line>:0:
include/linux/dynamic_debug.h:60:9: warning: 'buffer' may be used uninitialized in this function [-Wmaybe-uninitialized]
printk(KERN_DEBUG pr_fmt(fmt), ##__VA_ARGS__); \
^
/home/hans/work/build/media_build/v4l/videobuf2-core.c:2381:15: note: 'buffer' was declared here
unsigned int buffer, plane;
^
While these warnings are bogus (the call to __find_plane_by_offset will
set buffer and plane), it doesn't hurt to initialize these variables.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The stop_streaming op is only called if streaming is in progress,
so drop the unnecessary 'if (!vb2_is_streaming(vq))' check.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Pawel Osciak <pawel@osciak.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The vb2 core ignores any return code from the stop_streaming op.
And there really isn't anything it can do anyway in case of an error.
So change the return type to void and update any drivers that implement it.
The int return gave drivers the idea that this operation could actually
fail, but that's really not the case.
The pwc amd sdr-msi3101 drivers both had this construction:
if (mutex_lock_interruptible(&s->v4l2_lock))
return -ERESTARTSYS;
This has been updated to just call mutex_lock(). The stop_streaming op
expects this to really stop streaming and I very much doubt this will
work reliably if stop_streaming just returns without really stopping the
DMA.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Pawel Osciak <pawel@osciak.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Warnings due to __le16 / u16 conversions.
Replace offending struct and so stay on cpu domain.
Signed-off-by: Robert Butora <robert.butora.fi@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
External LNA between antenna connector and RF tuner is controlled
by EM28178 GPIO 0. GPIO value 1 is LNA active and value 0 is LNA
disabled.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
bit3 was not cleared always leaving driver reporting demod is not
fully locked. Do not check bit0 as it seems to be always 0.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
DVB-C uses lower frequencies than DVB-T. Extend frequency range down to
110 MHz in order to support DVB-C. 110 - 862 MHz range is defined by
NorDig Unified 2.2 specification.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Silicon Labs Si2157 silicon tuner driver.
Currently it supports only DVB-T.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
With the new vb2_thread_start/stop core code it is very easy to implement
videobuf2-dvb. This should simplify converting existing videobuf drivers to
vb2.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
In order to implement vb2 DVB support you need to be able to start
a kernel thread that queues and dequeues buffers, calling a callback
function for every buffer. This patch adds support for that.
It's based on drivers/media/v4l2-core/videobuf-dvb.c, but with all the DVB
specific stuff stripped out, thus making it much more generic.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The kernel debug messages produced by vb2 started either with a
lower or an upper case character. Switched all to use lower-case
which seemed to be what was used in the majority of the messages.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Pawel Osciak <pawel@osciak.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
It was impossible to read() or write() a frame if the queue type was multiplanar.
Even if the current format is single planar. Change this to just check whether
the number of planes is 1 or more.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Added a vb2_fileio_is_active inline function that returns true if fileio
is in progress. Check for this too in mmap() (you don't want apps mmap()ing
buffers used by fileio) and expbuf() (same reason).
In addition drivers should be able to check for this in queue_setup() to
return an error if an attempt is made to read() or write() with
V4L2_FIELD_ALTERNATE being configured. This is illegal (there is no way
to pass the TOP/BOTTOM information around using file I/O).
However, in order to be able to check for this the init_fileio function
needs to set q->fileio early on, before the buffers are allocated. So switch
to using internal functions (__reqbufs, vb2_internal_qbuf and
vb2_internal_streamon) to skip the fileio check. Well, that's why the internal
functions were created...
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Pawel Osciak <pawel@osciak.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
q->start_streaming_called is always true, so the WARN_ON check against
it being false can be dropped.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Pawel Osciak <pawel@osciak.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This is not allowed by the spec and does in fact not make any sense.
Return -EINVAL if this is the case.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Pawel Osciak <pawel@osciak.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
When using write() to write data to an output video node the vb2 core
should set timestamps if V4L2_BUF_FLAG_TIMESTAMP_COPY is set. Nobody
else is able to provide this information with the write() operation.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Pawel Osciak <pawel@osciak.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
__qbuf_mmap was sort of hidden in between the much larger __qbuf_userptr
and __qbuf_dmabuf functions. Move it before __qbuf_userptr which is
also conform the usual order these memory models are implemented: first
mmap, then userptr, then dmabuf.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Pawel Osciak <pawel@osciak.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Many dprintk's in vb2 use a hardcoded prefix with the function name. In
many cases that is now outdated. To keep things consistent the dprintk
macro has been changed to print the function name in addition to the "vb2:"
prefix. Superfluous prefixes elsewhere in the code have been removed.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Pawel Osciak <pawel@osciak.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The application should really always fill in bytesused for output
buffers, unfortunately the vb2 framework never checked for that.
So for single planar formats replace a bytesused of 0 by the length
of the buffer, and for multiplanar format do the same if bytesused is
0 for ALL planes.
This seems to be what the user really intended if v4l2_buffer was
just memset to 0.
I'm afraid that just checking for this and returning an error would
break too many applications. Quite a few drivers never check for bytesused
at all and just use the buffer length instead.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Pawel Osciak <pawel@osciak.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The videobuf2-core did not zero the 'planes' array in __qbuf_userptr()
and __qbuf_dmabuf(). That's now memset to 0. Without this the reserved
array in struct v4l2_plane would be non-zero, causing v4l2-compliance
errors.
More serious is the fact that data_offset was not handled correctly:
- for capture devices it was never zeroed, which meant that it was
uninitialized. Unless the driver sets it it was a completely random
number. With the memset above this is now fixed.
- __qbuf_dmabuf had a completely incorrect length check that included
data_offset.
- in __fill_vb2_buffer in the DMABUF case the data_offset field was
unconditionally copied from v4l2_buffer to v4l2_plane when this
should only happen in the output case.
- in the single-planar case data_offset was never correctly set to 0.
The single-planar API doesn't support data_offset, so setting it
to 0 is the right thing to do. This too is now solved by the memset.
All these issues were found with v4l2-compliance.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Pawel Osciak <pawel@osciak.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Add the new CEA-861-F and DMT 4K timings to the list of predefined
timings.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This patch migrates the vpfe driver to use v4l2_fh for
priority handling.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This patch migrates the vpbe driver to use v4l2_fh for
priority handling. This also fixes v4l2-compliance test.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This patch adds support for the PCI-8604PW card equipped with four 878A.
It is unknown who the manufacturer of this card is and no drivers were
available during development of the patch. According to images found
online, the card is originally sold with Linux DVR software.
A CPLD on the card prevents the 878A from requesting access to the
bus until an initialization sequence has been issued via GPIOs. The
implemented sequence uses the minimum number of GPIOs needed to
successfully unlock bus access. As there are many more GPIOs connected
to the CPLD, it is very likely that some of the others have an influence
on the bus arbitration scheduling. This should be investigated further
in case of performance issues.
The tested card contains an EEPROM on one of the 878A, but it is
completely empty (i.e. contains only 0xff), so it is not possible
to detect the card.
Signed-off-by: Daniel Glöckner <daniel-gl@gmx.net>
Tested-by: Robert Longbottom <rongblor@googlemail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
In core_init make sure access to EDID DDC lines are disabled
before chip is powered up. Also DISABLE_AUTO_EDID before power up.
The correct setting is applied later when setting the EDID.
Some sources (MAC) kept on reading EDID even when Hotplug was low
and in the short period in core_init before the DDC lines was enabled
read a corrupt EDID.
Signed-off-by: Martin Bugge <marbugge@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This was the reason for enabling the HDMI/DVI-D mode irq in the first place.
Signed-off-by: Martin Bugge <marbugge@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Fix the use of __user in the check_array_args() prototype: instead of
using 'void * __user *' you should use 'void __user **' for sparse to
understand this correctly.
This also required the use of __force in the '*kernel_ptr = user_ptr'
assignment.
Also replace a wrong cast (void *) with the correct one (void **)
in check_array_args().
This fixes these sparse warnings:
drivers/media/v4l2-core/v4l2-ioctl.c:2284:35: warning: incorrect type in assignment (different address spaces)
drivers/media/v4l2-core/v4l2-ioctl.c:2301:35: warning: incorrect type in assignment (different address spaces)
drivers/media/v4l2-core/v4l2-ioctl.c:2319:35: warning: incorrect type in assignment (different address spaces)
drivers/media/v4l2-core/v4l2-ioctl.c:2386:57: warning: incorrect type in argument 4 (different address spaces)
drivers/media/v4l2-core/v4l2-ioctl.c:2420:29: warning: incorrect type in assignment (different address spaces)
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Sparse generated a bunch of errors like this:
drivers/media/v4l2-core/videobuf2-core.c:2045:25: error: incompatible types in conditional expression (different base types)
drivers/media/v4l2-core/videobuf2-core.c:136:17: error: incompatible types in conditional expression (different base types)
drivers/media/v4l2-core/videobuf2-core.c:151:17: error: incompatible types in conditional expression (different base types)
drivers/media/v4l2-core/videobuf2-core.c:168:25: error: incompatible types in conditional expression (different base types)
drivers/media/v4l2-core/videobuf2-core.c:183:17: error: incompatible types in conditional expression (different base types)
drivers/media/v4l2-core/videobuf2-core.c:185:9: error: incompatible types in conditional expression (different base types)
drivers/media/v4l2-core/videobuf2-core.c:385:25: error: incompatible types in conditional expression (different base types)
drivers/media/v4l2-core/videobuf2-core.c:1115:17: error: incompatible types in conditional expression (different base types)
drivers/media/v4l2-core/videobuf2-core.c:1268:33: error: incompatible types in conditional expression (different base types)
drivers/media/v4l2-core/videobuf2-core.c:1270:25: error: incompatible types in conditional expression (different base types)
drivers/media/v4l2-core/videobuf2-core.c:1315:17: error: incompatible types in conditional expression (different base types)
drivers/media/v4l2-core/videobuf2-core.c:1324:25: error: incompatible types in conditional expression (different base types)
drivers/media/v4l2-core/videobuf2-core.c:1396:25: error: incompatible types in conditional expression (different base types)
drivers/media/v4l2-core/videobuf2-core.c:1457:17: error: incompatible types in conditional expression (different base types)
drivers/media/v4l2-core/videobuf2-core.c:1482:17: error: incompatible types in conditional expression (different base types)
drivers/media/v4l2-core/videobuf2-core.c:1484:9: error: incompatible types in conditional expression (different base types)
drivers/media/v4l2-core/videobuf2-core.c:1523:17: error: incompatible types in conditional expression (different base types)
drivers/media/v4l2-core/videobuf2-core.c:1525:17: error: incompatible types in conditional expression (different base types)
drivers/media/v4l2-core/videobuf2-core.c:1815:17: error: incompatible types in conditional expression (different base types)
drivers/media/v4l2-core/videobuf2-core.c:1828:17: error: incompatible types in conditional expression (different base types)
drivers/media/v4l2-core/videobuf2-core.c:1914:25: error: incompatible types in conditional expression (different base types)
drivers/media/v4l2-core/videobuf2-core.c:1944:9: error: incompatible types in conditional expression (different base types)
These are caused by the call*op defines which do something like this:
(ops->op) ? ops->op(args) : 0
which is OK as long as op is not a void function, because in that case one part
of the conditional expression returns void, the other an integer. Hence the sparse
errors.
I've replaced this by introducing three variants of the call_ macros:
call_*op for int returns, call_void_*op for void returns and call_ptr_*op for
pointer returns.
That's the bad news. The good news is that the fail_*op macros could be removed
since the call_*op macros now have enough information to determine if the op
succeeded or not and can increment the op counter only on success. This at least
makes it more robust w.r.t. future changes.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Pawel Osciak <pawel@osciak.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
There was some frequency calculation overflows which caused tuning
failure on 32-bit architecture. Use 64-bit numbers where needed in
order to avoid calculation overflows.
Thanks for the Finnish person, who asked remain anonymous, reporting,
testing and suggesting the fix.
Cc: <stable@vger.kernel.org>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
VIDEO_TIMBERDALE selects TIMB_DMA which itself depends on
MFD_TIMBERDALE, so VIDEO_TIMBERDALE should either select or depend on
MFD_TIMBERDALE as well. I chose to make it depend on it because I
think it makes more sense and it is consistent with what other options
are doing.
Adding a "|| HAS_IOMEM" to the TIMB_DMA dependencies silenced the
kconfig warning about unmet direct dependencies but it was wrong:
without MFD_TIMBERDALE, TIMB_DMA is useless as the driver has no
device to bind to.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Vinod Koul <vinod.koul@intel.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Mauro Carvalho Chehab <m.chehab@samsung.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This patch does not modify existing drivers. It adds subdriver
to gspca for DTCS033 (Scopium) webcam for astrophotography.
The patch adds dtcs033.c and modifies Kconfig and Makefile.
Signed-off-by: Robert Butora <robert.butora.fi@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The sn9c102 driver is deprecated. It was moved to staging in
anticipation of its removal in a future kernel version. However, USB
devices 0C45:6024 and 0C45:6025 are still handled by sn9c102 when
both sn9c102 and gspca_sonixb are enabled.
We must migrate all the users of these devices to the gspca_sonixb
driver now, so that it gets sufficient testing before the sn9c102
driver is finally phased out.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
from commit-id: b3379c6201
"vb2: only call start_streaming if sufficient buffers are queued"
the vb2 framework warns on (WARN_ON()) if all the active buffers
are not released when streaming is stopped, initially the vb2 silently
released the buffer internally if the buffer was not released by
the driver.
This patch fixes following issue:
WARNING: CPU: 0 PID: 2049 at drivers/media/v4l2-core/videobuf2-core.c:2011 __vb2_queue_cancel+0x1a0/0x218()
Modules linked in:
CPU: 0 PID: 2049 Comm: vpbe_display Tainted: G W 3.14.0-rc5-00414-ged97a6f #89
[<c000e3f0>] (unwind_backtrace) from [<c000c618>] (show_stack+0x10/0x14)
[<c000c618>] (show_stack) from [<c001adb0>] (warn_slowpath_common+0x68/0x88)
[<c001adb0>] (warn_slowpath_common) from [<c001adec>] (warn_slowpath_null+0x1c/0x24)
[<c001adec>] (warn_slowpath_null) from [<c0252e0c>] (__vb2_queue_cancel+0x1a0/0x218)
[<c0252e0c>] (__vb2_queue_cancel) from [<c02533a4>] (vb2_queue_release+0x14/0x24)
[<c02533a4>] (vb2_queue_release) from [<c025a65c>] (vpbe_display_release+0x60/0x230)
[<c025a65c>] (vpbe_display_release) from [<c023fe5c>] (v4l2_release+0x34/0x74)
[<c023fe5c>] (v4l2_release) from [<c00b4a00>] (__fput+0x80/0x224)
[<c00b4a00>] (__fput) from [<c00341e8>] (task_work_run+0xa0/0xd0)
[<c00341e8>] (task_work_run) from [<c001cc28>] (do_exit+0x244/0x918)
[<c001cc28>] (do_exit) from [<c001d344>] (do_group_exit+0x48/0xdc)
[<c001d344>] (do_group_exit) from [<c0029894>] (get_signal_to_deliver+0x2a0/0x5bc)
[<c0029894>] (get_signal_to_deliver) from [<c000b888>] (do_signal+0x78/0x3a0)
[<c000b888>] (do_signal) from [<c000bc54>] (do_work_pending+0xa4/0xb4)
[<c000bc54>] (do_work_pending) from [<c00096dc>] (work_pending+0xc/0x20)
---[ end trace 5faa75e8c2f8a6a1 ]---
------------[ cut here ]------------
WARNING: CPU: 0 PID: 2049 at drivers/media/v4l2-core/videobuf2-core.c:1095 vb2_buffer_done+0x1e0/0x224()
Modules linked in:
CPU: 0 PID: 2049 Comm: vpbe_display Tainted: G W 3.14.0-rc5-00414-ged97a6f #89
[<c000e3f0>] (unwind_backtrace) from [<c000c618>] (show_stack+0x10/0x14)
[<c000c618>] (show_stack) from [<c001adb0>] (warn_slowpath_common+0x68/0x88)
[<c001adb0>] (warn_slowpath_common) from [<c001adec>] (warn_slowpath_null+0x1c/0x24)
[<c001adec>] (warn_slowpath_null) from [<c0252c28>] (vb2_buffer_done+0x1e0/0x224)
[<c0252c28>] (vb2_buffer_done) from [<c0252e3c>] (__vb2_queue_cancel+0x1d0/0x218)
[<c0252e3c>] (__vb2_queue_cancel) from [<c02533a4>] (vb2_queue_release+0x14/0x24)
[<c02533a4>] (vb2_queue_release) from [<c025a65c>] (vpbe_display_release+0x60/0x230)
[<c025a65c>] (vpbe_display_release) from [<c023fe5c>] (v4l2_release+0x34/0x74)
[<c023fe5c>] (v4l2_release) from [<c00b4a00>] (__fput+0x80/0x224)
[<c00b4a00>] (__fput) from [<c00341e8>] (task_work_run+0xa0/0xd0)
[<c00341e8>] (task_work_run) from [<c001cc28>] (do_exit+0x244/0x918)
[<c001cc28>] (do_exit) from [<c001d344>] (do_group_exit+0x48/0xdc)
[<c001d344>] (do_group_exit) from [<c0029894>] (get_signal_to_deliver+0x2a0/0x5bc)
[<c0029894>] (get_signal_to_deliver) from [<c000b888>] (do_signal+0x78/0x3a0)
[<c000b888>] (do_signal) from [<c000bc54>] (do_work_pending+0xa4/0xb4)
[<c000bc54>] (do_work_pending) from [<c00096dc>] (work_pending+0xc/0x20)
---[ end trace 5faa75e8c2f8a6a2 ]---
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
from commit-id: b3379c6201
"vb2: only call start_streaming if sufficient buffers are queued"
the vb2 framework warns on (WARN_ON()) if all the active buffers
are not released when streaming is stopped, initially the vb2 silently
released the buffer internally if the buffer was not released by
the driver.
Also this patch moves the disabling of interrupts from relase() callback
to stop_streaming() callback as which needs to be done ideally.
This patch fixes following issue:
WARNING: CPU: 0 PID: 2049 at drivers/media/v4l2-core/videobuf2-core.c:2011 __vb2_queue_cancel+0x1a0/0x218()
Modules linked in:
CPU: 0 PID: 2049 Comm: vpif_display Tainted: G W 3.14.0-rc5-00414-ged97a6f #89
[<c000e3f0>] (unwind_backtrace) from [<c000c618>] (show_stack+0x10/0x14)
[<c000c618>] (show_stack) from [<c001adb0>] (warn_slowpath_common+0x68/0x88)
[<c001adb0>] (warn_slowpath_common) from [<c001adec>] (warn_slowpath_null+0x1c/0x24)
[<c001adec>] (warn_slowpath_null) from [<c0252e0c>] (__vb2_queue_cancel+0x1a0/0x218)
[<c0252e0c>] (__vb2_queue_cancel) from [<c02533a4>] (vb2_queue_release+0x14/0x24)
[<c02533a4>] (vb2_queue_release) from [<c025a65c>] (vpif_release+0x60/0x230)
[<c025a65c>] (vpif_release) from [<c023fe5c>] (v4l2_release+0x34/0x74)
[<c023fe5c>] (v4l2_release) from [<c00b4a00>] (__fput+0x80/0x224)
[<c00b4a00>] (__fput) from [<c00341e8>] (task_work_run+0xa0/0xd0)
[<c00341e8>] (task_work_run) from [<c001cc28>] (do_exit+0x244/0x918)
[<c001cc28>] (do_exit) from [<c001d344>] (do_group_exit+0x48/0xdc)
[<c001d344>] (do_group_exit) from [<c0029894>] (get_signal_to_deliver+0x2a0/0x5bc)
[<c0029894>] (get_signal_to_deliver) from [<c000b888>] (do_signal+0x78/0x3a0)
[<c000b888>] (do_signal) from [<c000bc54>] (do_work_pending+0xa4/0xb4)
[<c000bc54>] (do_work_pending) from [<c00096dc>] (work_pending+0xc/0x20)
---[ end trace 5faa75e8c2f8a6a1 ]---
------------[ cut here ]------------
WARNING: CPU: 0 PID: 2049 at drivers/media/v4l2-core/videobuf2-core.c:1095 vb2_buffer_done+0x1e0/0x224()
Modules linked in:
CPU: 0 PID: 2049 Comm: vpif_display Tainted: G W 3.14.0-rc5-00414-ged97a6f #89
[<c000e3f0>] (unwind_backtrace) from [<c000c618>] (show_stack+0x10/0x14)
[<c000c618>] (show_stack) from [<c001adb0>] (warn_slowpath_common+0x68/0x88)
[<c001adb0>] (warn_slowpath_common) from [<c001adec>] (warn_slowpath_null+0x1c/0x24)
[<c001adec>] (warn_slowpath_null) from [<c0252c28>] (vb2_buffer_done+0x1e0/0x224)
[<c0252c28>] (vb2_buffer_done) from [<c0252e3c>] (__vb2_queue_cancel+0x1d0/0x218)
[<c0252e3c>] (__vb2_queue_cancel) from [<c02533a4>] (vb2_queue_release+0x14/0x24)
[<c02533a4>] (vb2_queue_release) from [<c025a65c>] (vpif_release+0x60/0x230)
[<c025a65c>] (vpif_release) from [<c023fe5c>] (v4l2_release+0x34/0x74)
[<c023fe5c>] (v4l2_release) from [<c00b4a00>] (__fput+0x80/0x224)
[<c00b4a00>] (__fput) from [<c00341e8>] (task_work_run+0xa0/0xd0)
[<c00341e8>] (task_work_run) from [<c001cc28>] (do_exit+0x244/0x918)
[<c001cc28>] (do_exit) from [<c001d344>] (do_group_exit+0x48/0xdc)
[<c001d344>] (do_group_exit) from [<c0029894>] (get_signal_to_deliver+0x2a0/0x5bc)
[<c0029894>] (get_signal_to_deliver) from [<c000b888>] (do_signal+0x78/0x3a0)
[<c000b888>] (do_signal) from [<c000bc54>] (do_work_pending+0xa4/0xb4)
[<c000bc54>] (do_work_pending) from [<c00096dc>] (work_pending+0xc/0x20)
---[ end trace 5faa75e8c2f8a6a2 ]---
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
from commit-id: b3379c6201
"vb2: only call start_streaming if sufficient buffers are queued"
the vb2 framework warns on (WARN_ON()) if all the active buffers
are not released when streaming is stopped, initially the vb2 silently
released the buffer internally if the buffer was not released by
the driver.
Also this patch moves the disabling of interrupts from relase() callback
to stop_streaming() callback as which needs to be done ideally.
This patch fixes following issue:
WARNING: CPU: 0 PID: 2049 at drivers/media/v4l2-core/videobuf2-core.c:2011 __vb2_queue_cancel+0x1a0/0x218()
Modules linked in:
CPU: 0 PID: 2049 Comm: vpif_capture Tainted: G W 3.14.0-rc5-00414-ged97a6f #89
[<c000e3f0>] (unwind_backtrace) from [<c000c618>] (show_stack+0x10/0x14)
[<c000c618>] (show_stack) from [<c001adb0>] (warn_slowpath_common+0x68/0x88)
[<c001adb0>] (warn_slowpath_common) from [<c001adec>] (warn_slowpath_null+0x1c/0x24)
[<c001adec>] (warn_slowpath_null) from [<c0252e0c>] (__vb2_queue_cancel+0x1a0/0x218)
[<c0252e0c>] (__vb2_queue_cancel) from [<c02533a4>] (vb2_queue_release+0x14/0x24)
[<c02533a4>] (vb2_queue_release) from [<c025a65c>] (vpif_release+0x60/0x230)
[<c025a65c>] (vpif_release) from [<c023fe5c>] (v4l2_release+0x34/0x74)
[<c023fe5c>] (v4l2_release) from [<c00b4a00>] (__fput+0x80/0x224)
[<c00b4a00>] (__fput) from [<c00341e8>] (task_work_run+0xa0/0xd0)
[<c00341e8>] (task_work_run) from [<c001cc28>] (do_exit+0x244/0x918)
[<c001cc28>] (do_exit) from [<c001d344>] (do_group_exit+0x48/0xdc)
[<c001d344>] (do_group_exit) from [<c0029894>] (get_signal_to_deliver+0x2a0/0x5bc)
[<c0029894>] (get_signal_to_deliver) from [<c000b888>] (do_signal+0x78/0x3a0)
[<c000b888>] (do_signal) from [<c000bc54>] (do_work_pending+0xa4/0xb4)
[<c000bc54>] (do_work_pending) from [<c00096dc>] (work_pending+0xc/0x20)
---[ end trace 5faa75e8c2f8a6a1 ]---
------------[ cut here ]------------
WARNING: CPU: 0 PID: 2049 at drivers/media/v4l2-core/videobuf2-core.c:1095 vb2_buffer_done+0x1e0/0x224()
Modules linked in:
CPU: 0 PID: 2049 Comm: vpif_capture Tainted: G W 3.14.0-rc5-00414-ged97a6f #89
[<c000e3f0>] (unwind_backtrace) from [<c000c618>] (show_stack+0x10/0x14)
[<c000c618>] (show_stack) from [<c001adb0>] (warn_slowpath_common+0x68/0x88)
[<c001adb0>] (warn_slowpath_common) from [<c001adec>] (warn_slowpath_null+0x1c/0x24)
[<c001adec>] (warn_slowpath_null) from [<c0252c28>] (vb2_buffer_done+0x1e0/0x224)
[<c0252c28>] (vb2_buffer_done) from [<c0252e3c>] (__vb2_queue_cancel+0x1d0/0x218)
[<c0252e3c>] (__vb2_queue_cancel) from [<c02533a4>] (vb2_queue_release+0x14/0x24)
[<c02533a4>] (vb2_queue_release) from [<c025a65c>] (vpif_release+0x60/0x230)
[<c025a65c>] (vpif_release) from [<c023fe5c>] (v4l2_release+0x34/0x74)
[<c023fe5c>] (v4l2_release) from [<c00b4a00>] (__fput+0x80/0x224)
[<c00b4a00>] (__fput) from [<c00341e8>] (task_work_run+0xa0/0xd0)
[<c00341e8>] (task_work_run) from [<c001cc28>] (do_exit+0x244/0x918)
[<c001cc28>] (do_exit) from [<c001d344>] (do_group_exit+0x48/0xdc)
[<c001d344>] (do_group_exit) from [<c0029894>] (get_signal_to_deliver+0x2a0/0x5bc)
[<c0029894>] (get_signal_to_deliver) from [<c000b888>] (do_signal+0x78/0x3a0)
[<c000b888>] (do_signal) from [<c000bc54>] (do_work_pending+0xa4/0xb4)
[<c000bc54>] (do_work_pending) from [<c00096dc>] (work_pending+0xc/0x20)
---[ end trace 5faa75e8c2f8a6a2 ]---
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
All YUV 422 has 16bit per pixels.
Signed-off-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This fixes following build error:
CC drivers/media/i2c/s5c73m3/s5c73m3-core.o
CC drivers/md/dm-ioctl.o
CC net/ipv4/inet_lro.o
drivers/media/i2c/s5c73m3/s5c73m3-core.c: In function ‘s5c73m3_get_platform_data’:
drivers/media/i2c/s5c73m3/s5c73m3-core.c:1619:2: error: implicit declaration of function ‘v4l2_of_get_next_endpoint’ [-Werror=implicit-function-declaration]
drivers/media/i2c/s5c73m3/s5c73m3-core.c:1619:10: warning: assignment makes pointer from integer without a cast [enabled by default]
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
