The phylink conflict was between a bug fix by Russell King
to make sure we have a consistent PHY interface mode, and
a change in net-next to pull some code in phylink_resolve()
into the helper functions phylink_mac_link_{up,down}()
On the dp83867 side it's mostly overlapping changes, with
the 'net' side removing a condition that was supposed to
trigger for RGMII but because of how it was coded never
actually could trigger.
Signed-off-by: David S. Miller <davem@davemloft.net>
Add binding documentation for Atheros/QCA networking IP core used
in many routers.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add new interface mode USXGMII to binding documentation.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The clock output is generally only used for testing and development and
not used to daisy-chain PHYs. It's just a source of RF noise afterward.
Add a mux value for "off". I've added it as another enumeration to the
output property. In the actual PHY, the mux and the output enable are
independently controllable. However, it doesn't seem useful to be able
to describe the mux setting when the output is disabled.
Document that PHY's default setting will be left as is if the property
is omitted.
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Trent Piepho <tpiepho@impinj.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a note to make it more clear how the driver behaves when "rgmii" vs
"rgmii-id", "rgmii-idrx", or "rgmii-idtx" interface modes are selected.
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Trent Piepho <tpiepho@impinj.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
nand-controller.yaml replaced nand.txt however the references to it were
not updated. This change updates these references wherever it appears in
bindings documentation.
Fixes: 212e496935 ("dt-bindings: mtd: Add YAML schemas for the generic NAND options")
Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Validating the examples against the schema have a few errors:
arm,gic.example.dt.yaml: 'ranges' does not match any of the regexes: '^v2m@[0-9a-f]+$', 'pinctrl-[0-9]+'
arm,gic.example.dt.yaml: #address-cells:0:0: 2 is not one of [0, 1]
arm,gic.example.dt.yaml: #size-cells:0:0: 1 was expected
'ranges' is valid, but missing from the schema, so add it. The reg
addresses and sizes don't match the schema requirements and the example
template. We could just override the example template to use 64-bit
addresses, but there's not really any value showing that in the example.
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Following commit 31af04cd60 ("arm64: dts: Remove inconsistent use of
'arm,armv8' compatible string"), clean up these binding examples in case
anyone is tempted to copy them.
CC: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Rob Herring <robh@kernel.org>
These files were converted to json-schema, but the references weren't
renamed.
Fixes: 66ed144f14 ("dt-bindings: interrupt-controller: Convert ARM GIC to json-schema")
(and other similar commits)
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Rob Herring <robh@kernel.org>
In order to have $ref's to schema files within the kernel, we need to
pass the base path of bindings to the schema validation tools.
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Michal Marek <michal.lkml@markovi.net>
Cc: devicetree@vger.kernel.org
Cc: linux-kbuild@vger.kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
For IP blocks that are generated from the public, open-source
sifive-blocks repository, describe the version numbering policy
that its maintainers intend to use, upon request from Rob
Herring <robh@kernel.org>.
Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Reviewed-by: Palmer Dabbelt <palmer@sifive.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Palmer Dabbelt <palmer@sifive.com>
Cc: Megan Wachs <megan@sifive.com>
Cc: Wesley Terpstra <wesley@sifive.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: devicetree@vger.kernel.org
Cc: linux-riscv@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Pull clocksource updates from Ingo Molnar:
"Misc clocksource/clockevent driver updates that came in a bit late but
are ready for v5.2"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
misc: atmel_tclib: Do not probe already used TCBs
clocksource/drivers/timer-atmel-tcb: Convert tc_clksrc_suspend|resume() to static
clocksource/drivers/tcb_clksrc: Rename the file for consistency
clocksource/drivers/timer-atmel-pit: Rework Kconfig option
clocksource/drivers/tcb_clksrc: Move Kconfig option
ARM: at91: Implement clocksource selection
clocksource/drivers/tcb_clksrc: Use tcb as sched_clock
clocksource/drivers/tcb_clksrc: Stop depending on atmel_tclib
ARM: at91: move SoC specific definitions to SoC folder
clocksource/drivers/timer-milbeaut: Cleanup common register accesses
clocksource/drivers/timer-milbeaut: Add shutdown function
clocksource/drivers/timer-milbeaut: Fix to enable one-shot timer
clocksource/drivers/tegra: Rework for compensation of suspend time
clocksource/drivers/sp804: Add COMPILE_TEST to CONFIG_ARM_TIMER_SP804
clocksource/drivers/sun4i: Add a compatible for suniv
dt-bindings: timer: Add Allwinner suniv timer
Pull IRQ chip updates from Ingo Molnar:
"A late irqchips update:
- New TI INTR/INTA set of drivers
- Rewrite of the stm32mp1-exti driver as a platform driver
- Update the IOMMU MSI mapping API to be RT friendly
- A number of cleanups and other low impact fixes"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (34 commits)
iommu/dma-iommu: Remove iommu_dma_map_msi_msg()
irqchip/gic-v3-mbi: Don't map the MSI page in mbi_compose_m{b, s}i_msg()
irqchip/ls-scfg-msi: Don't map the MSI page in ls_scfg_msi_compose_msg()
irqchip/gic-v3-its: Don't map the MSI page in its_irq_compose_msi_msg()
irqchip/gicv2m: Don't map the MSI page in gicv2m_compose_msi_msg()
iommu/dma-iommu: Split iommu_dma_map_msi_msg() in two parts
genirq/msi: Add a new field in msi_desc to store an IOMMU cookie
arm64: arch_k3: Enable interrupt controller drivers
irqchip/ti-sci-inta: Add msi domain support
soc: ti: Add MSI domain bus support for Interrupt Aggregator
irqchip/ti-sci-inta: Add support for Interrupt Aggregator driver
dt-bindings: irqchip: Introduce TISCI Interrupt Aggregator bindings
irqchip/ti-sci-intr: Add support for Interrupt Router driver
dt-bindings: irqchip: Introduce TISCI Interrupt router bindings
gpio: thunderx: Use the default parent apis for {request,release}_resources
genirq: Introduce irq_chip_{request,release}_resource_parent() apis
firmware: ti_sci: Add helper apis to manage resources
firmware: ti_sci: Add RM mapping table for am654
firmware: ti_sci: Add support for IRQ management
firmware: ti_sci: Add support for RM core ops
...
This is some material that we picked up into our tree late. Most of it
are smaller fixes and additions, some defconfig updates due to recent
development, etc.
Code-wise the largest portion is a series of PM updates for the at91
platform, and those have been in linux-next a while through the at91
tree before we picked them up.
-----BEGIN PGP SIGNATURE-----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=XCCp
-----END PGP SIGNATURE-----
Merge tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC late updates from Olof Johansson:
"This is some material that we picked up into our tree late. Most of it
are smaller fixes and additions, some defconfig updates due to recent
development, etc.
Code-wise the largest portion is a series of PM updates for the at91
platform, and those have been in linux-next a while through the at91
tree before we picked them up"
* tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (29 commits)
arm64: dts: sprd: Add clock properties for serial devices
Opt out of scripts/get_maintainer.pl
ARM: ixp4xx: Remove duplicated include from common.c
soc: ixp4xx: qmgr: Fix an NULL vs IS_ERR() check in probe
arm64: tegra: Disable XUSB support on Jetson TX2
arm64: tegra: Enable SMMU translation for PCI on Tegra186
arm64: tegra: Fix insecure SMMU users for Tegra186
arm64: tegra: Select ARM_GIC_PM
amba: tegra-ahb: Mark PM functions as __maybe_unused
ARM: dts: logicpd-som-lv: Fix MMC1 card detect
ARM: mvebu: drop return from void function
ARM: mvebu: prefix coprocessor operand with p
ARM: mvebu: drop unnecessary label
ARM: mvebu: fix a leaked reference by adding missing of_node_put
ARM: socfpga_defconfig: enable LTC2497
ARM: mvebu: kirkwood: remove error message when retrieving mac address
ARM: at91: sama5: make ov2640 as a module
ARM: OMAP1: ams-delta: fix early boot crash when LED support is disabled
ARM: at91: remove HAVE_FB_ATMEL for sama5 SoC as they use DRM
soc/fsl/qe: Fix an error code in qe_pin_request()
...
This patch set contains an assortment of RISC-V related patches that I'd
like to target for the 5.2 merge window. Most of the patches are
cleanups, but there are a handful of user-visible changes:
* The nosmp and nr_cpus command-line arguments are now supported, which
work like normal.
* The SBI console no longer installs itself as a preferred console, we
rely on standard mechanisms (/chosen, command-line, hueristics)
instead.
* sfence_remove_sfence_vma{,_asid} now pass their arguments along to the
SBI call.
* Modules now support BUG().
* A missing sfence.vma during boot has been added. This bug only
manifests during boot.
* The arch/riscv support for SiFive's L2 cache controller has been
merged, which should un-block the EDAC framework work.
I've only tested this on QEMU again, as I didn't have time to get things
running on the Unleashed. The latest master from this morning merges in
cleanly and passes the tests as well.
This patch set rebased my "5.2 MW, Part 1" patch set which includes an
erronous empty file. It's also a rebase of my "5.2 MW, Part 2" patch
set, in which I managed to create another file while attempting to
remove the empty file.
Sorry for all the noise!
-----BEGIN PGP SIGNATURE-----
iQJHBAABCAAxFiEEAM520YNJYN/OiG3470yhUCzLq0EFAlzeLhUTHHBhbG1lckBk
YWJiZWx0LmNvbQAKCRDvTKFQLMurQXV/D/9nz8KYxNKOVIXft27mw93Qnx5joblg
fibA7nGDuxCszSC3tfyaROJZuGKe1G24vP4RG7aVs+iwRmmFhtVdPwm7ZvIr+DfU
a5mzwWkxhMZP8lgxMAIn7iM/NWrBm7rWdGTU0BYjHlGkQ5z3WA67rU/r/vrowhUN
zK1U/ATLvFWDJv5rdDj8/T2rDJzWtAsuy2qlmQN30CCJoOXXgIdAj+fVG4IYoxO9
2+NFJU4Y0a+YczWW3qaGFjTaYYt/sNr/uA8AoBNqV1NvsopK1UO3txbcfJwvZZC3
JFU9WBjC7xuF2ihMWecIZ7XljZeqhlsP7lZDizatQ/mdL9k7+6elk1sdcNLC23dN
VWJakudE42dISCwSh49fAbeNSl/3R5VWSlZmVO18gsmslkGa4FwuoKjklnxx7hYx
fQfvaqMIEXy3YmKtmFneUXLdcGoWOjV0FfDh5Ye582tAmB2TzvgEJHPJI7suUA/a
RkZHcmVJTSRBMe2fS0qkYxy/wdIDtRW2yjypssl9G6zQPPCVW+maD70m/9oVdsgm
IL8MpoDxW0uAYsV8Ctt1/+Ux+BObMADIml/1HPQyBRA0qhorQQWk0TcbjEXeIShs
OOG8byAQUJx98z62zrKQ53+Pxdevcja6uKxu3f0yEHxl19dBJdT2BM6rjs3sO1hi
c3tX/U8o39H0Kg==
=mZwx
-----END PGP SIGNATURE-----
Merge tag 'riscv-for-linus-5.2-mw2' of git://git.kernel.org/pub/scm/linux/kernel/git/palmer/riscv-linux
Pull RISC-V updates from Palmer Dabbelt:
"This contains an assortment of RISC-V related patches that I'd like to
target for the 5.2 merge window. Most of the patches are cleanups, but
there are a handful of user-visible changes:
- The nosmp and nr_cpus command-line arguments are now supported,
which work like normal.
- The SBI console no longer installs itself as a preferred console,
we rely on standard mechanisms (/chosen, command-line, hueristics)
instead.
- sfence_remove_sfence_vma{,_asid} now pass their arguments along to
the SBI call.
- Modules now support BUG().
- A missing sfence.vma during boot has been added. This bug only
manifests during boot.
- The arch/riscv support for SiFive's L2 cache controller has been
merged, which should un-block the EDAC framework work.
I've only tested this on QEMU again, as I didn't have time to get
things running on the Unleashed. The latest master from this morning
merges in cleanly and passes the tests as well"
* tag 'riscv-for-linus-5.2-mw2' of git://git.kernel.org/pub/scm/linux/kernel/git/palmer/riscv-linux: (31 commits)
riscv: fix locking violation in page fault handler
RISC-V: sifive_l2_cache: Add L2 cache controller driver for SiFive SoCs
RISC-V: Add DT documentation for SiFive L2 Cache Controller
RISC-V: Avoid using invalid intermediate translations
riscv: Support BUG() in kernel module
riscv: Add the support for c.ebreak check in is_valid_bugaddr()
riscv: support trap-based WARN()
riscv: fix sbi_remote_sfence_vma{,_asid}.
riscv: move switch_mm to its own file
riscv: move flush_icache_{all,mm} to cacheflush.c
tty: Don't force RISCV SBI console as preferred console
RISC-V: Access CSRs using CSR numbers
RISC-V: Add interrupt related SCAUSE defines in asm/csr.h
RISC-V: Use tabs to align macro values in asm/csr.h
RISC-V: Fix minor checkpatch issues.
RISC-V: Support nr_cpus command line option.
RISC-V: Implement nosmp commandline option.
RISC-V: Add RISC-V specific arch_match_cpu_phys_id
riscv: vdso: drop unnecessary cc-ldoption
riscv: call pm_power_off from machine_halt / machine_power_off
...
Convert the vendor prefix registry to a schema. This will enable checking
that new vendor prefixes are added (in addition to the less than perfect
checkpatch.pl check) and will also check against adding other prefixes
which are not vendors.
Converted vendor-prefixes.txt using the following sed script:
sed -e 's/\([a-zA-Z0-9\-]*\)[[:space:]]*\([a-zA-Z0-9].*\)/ "^\1,\.\*\":\n description: \2/'
Signed-off-by: Rob Herring <robh@kernel.org>
Various driver updates for platforms and a couple of the small driver
subsystems we merge through our tree:
Among the larger pieces:
- Power management improvements for TI am335x and am437x (RTC suspend/wake)
- Misc new additions for Amlogic (socinfo updates)
- ZynqMP FPGA manager
- Nvidia improvements for reset/powergate handling
- PMIC wrapper for Mediatek MT8516
- Misc fixes/improvements for ARM SCMI, TEE, NXP i.MX SCU drivers
-----BEGIN PGP SIGNATURE-----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=YSfu
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC-related driver updates from Olof Johansson:
"Various driver updates for platforms and a couple of the small driver
subsystems we merge through our tree:
Among the larger pieces:
- Power management improvements for TI am335x and am437x (RTC
suspend/wake)
- Misc new additions for Amlogic (socinfo updates)
- ZynqMP FPGA manager
- Nvidia improvements for reset/powergate handling
- PMIC wrapper for Mediatek MT8516
- Misc fixes/improvements for ARM SCMI, TEE, NXP i.MX SCU drivers"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (57 commits)
soc: aspeed: fix Kconfig
soc: add aspeed folder and misc drivers
spi: zynqmp: Fix build break
soc: imx: Add generic i.MX8 SoC driver
MAINTAINERS: Update email for Qualcomm SoC maintainer
memory: tegra: Fix a typos for "fdcdwr2" mc client
Revert "ARM: tegra: Restore memory arbitration on resume from LP1 on Tegra30+"
memory: tegra: Replace readl-writel with mc_readl-mc_writel
memory: tegra: Fix integer overflow on tick value calculation
memory: tegra: Fix missed registers values latching
ARM: tegra: cpuidle: Handle tick broadcasting within cpuidle core on Tegra20/30
optee: allow to work without static shared memory
soc/tegra: pmc: Move powergate initialisation to probe
soc/tegra: pmc: Remove reset sysfs entries on error
soc/tegra: pmc: Fix reset sources and levels
soc: amlogic: meson-gx-pwrc-vpu: Add support for G12A
soc: amlogic: meson-gx-pwrc-vpu: Fix power on/off register bitmask
fpga manager: Adding FPGA Manager support for Xilinx zynqmp
dt-bindings: fpga: Add bindings for ZynqMP fpga driver
firmware: xilinx: Add fpga API's
...
SoC updates, mostly refactorings and cleanups of old legacy platforms.
Major themes this release:
- Conversion of ixp4xx to a modern platform (drivers, DT, bindings)
- Moving some of the ep93xx headers around to get it closer to multiplatform enabled.
- Cleanups of Davinci
This tag also contains a few patches that were queued up as fixes before
5.1 but I didn't get sent in before release.
-----BEGIN PGP SIGNATURE-----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=pUeO
-----END PGP SIGNATURE-----
Merge tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC platform updates from Olof Johansson:
"SoC updates, mostly refactorings and cleanups of old legacy platforms.
Major themes this release:
- Conversion of ixp4xx to a modern platform (drivers, DT, bindings)
- Moving some of the ep93xx headers around to get it closer to
multiplatform enabled.
- Cleanups of Davinci
This also contains a few patches that were queued up as fixes before
5.1 but I didn't get sent in before release"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (123 commits)
ARM: debug-ll: add default address for digicolor
ARM: u300: regulator: add MODULE_LICENSE()
ARM: ep93xx: move private headers out of mach/*
ARM: ep93xx: move pinctrl interfaces into include/linux/soc
ARM: ep93xx: keypad: stop using mach/platform.h
ARM: ep93xx: move network platform data to separate header
ARM: stm32: add AMBA support for stm32 family
MAINTAINERS: update arch/arm/mach-davinci
ARM: rockchip: add missing of_node_put in rockchip_smp_prepare_pmu
ARM: dts: Add queue manager and NPE to the IXP4xx DTSI
soc: ixp4xx: qmgr: Add DT probe code
soc: ixp4xx: qmgr: Add DT bindings for IXP4xx qmgr
soc: ixp4xx: npe: Add DT probe code
soc: ixp4xx: Add DT bindings for IXP4xx NPE
soc: ixp4xx: qmgr: Pass resources
soc: ixp4xx: Remove unused functions
soc: ixp4xx: Uninline several functions
soc: ixp4xx: npe: Pass addresses as resources
ARM: ixp4xx: Turn the QMGR into a platform device
ARM: ixp4xx: Turn the NPE into a platform device
...
Pull thermal soc updates from Eduardo Valentin:
- thermal core has a new devm_* API for registering cooling devices. I
took the entire series, that is why you see changes on drivers/hwmon
in this pull (Guenter Roeck)
- rockchip thermal driver gains support to PX30 SoC (Elaine Zhang)
- the generic-adc thermal driver now considers the lookup table DT
property as optional (Jean-Francois Dagenais)
- Refactoring of tsens thermal driver (Amit Kucheria)
- Cleanups on cpu cooling driver (Daniel Lezcano)
- broadcom thermal driver dropped support to ACPI (Srinath Mannam)
- tegra thermal driver gains support to OC hw throttle and GPU throtle
(Wei Ni)
- Fixes in several thermal drivers.
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/evalenti/linux-soc-thermal: (59 commits)
hwmon: (pwm-fan) Use devm_thermal_of_cooling_device_register
hwmon: (npcm750-pwm-fan) Use devm_thermal_of_cooling_device_register
hwmon: (mlxreg-fan) Use devm_thermal_of_cooling_device_register
hwmon: (gpio-fan) Use devm_thermal_of_cooling_device_register
hwmon: (aspeed-pwm-tacho) Use devm_thermal_of_cooling_device_register
thermal: rcar_gen3_thermal: Fix to show correct trip points number
thermal: rcar_thermal: update calculation formula for R-Car Gen3 SoCs
thermal: cpu_cooling: Actually trace CPU load in thermal_power_cpu_get_power
thermal: rockchip: Support the PX30 SoC in thermal driver
dt-bindings: rockchip-thermal: Support the PX30 SoC compatible
thermal: rockchip: fix up the tsadc pinctrl setting error
thermal: broadcom: Remove ACPI support
thermal: Fix build error of missing devm_ioremap_resource on UM
thermal/drivers/cpu_cooling: Remove pointless field
thermal/drivers/cpu_cooling: Add Software Package Data Exchange (SPDX)
thermal/drivers/cpu_cooling: Fixup the header and copyright
thermal/drivers/cpu_cooling: Remove pointless test in power2state()
thermal: rcar_gen3_thermal: disable interrupt in .remove
thermal: rcar_gen3_thermal: fix interrupt type
thermal: Introduce devm_thermal_of_cooling_device_register
...
Merge in a few pending fixes from pre-5.1 that didn't get sent in:
MAINTAINERS: update arch/arm/mach-davinci
ARM: dts: ls1021: Fix SGMII PCS link remaining down after PHY disconnect
ARM: dts: imx6q-logicpd: Reduce inrush current on USBH1
ARM: dts: imx6q-logicpd: Reduce inrush current on start
ARM: dts: imx: Fix the AR803X phy-mode
ARM: dts: sun8i: a33: Reintroduce default pinctrl muxing
arm64: dts: allwinner: a64: Rename hpvcc-supply to cpvdd-supply
ARM: sunxi: fix a leaked reference by adding missing of_node_put
ARM: sunxi: fix a leaked reference by adding missing of_node_put
Signed-off-by: Olof Johansson <olof@lixom.net>
Core:
* Add over-current health state
* Add standard, adaptive and custom charge types
* Add new properties for start/end charge threshold
New Drivers / Hardware:
* UCS1002 Programmable USB Port Power Controller
* Ingenic JZ47xx Battery Fuel Gauge
* AXP20x USB Power: Add AXP813 support
* AT91 poweroff: Add SAM9X60 support
* OLPC battery: Add XO-1.5 and XO-1.75 support
Misc. Changes:
* syscon-reboot: support mask property
* AXP288 fuel gauge: Blacklist ACEPC T8/T11
- Looks like some vendor thought it's a good idea to
build a desktop system with a fuel gauge, that slowly
"discharges"...
* cpcap-battery: Fix calculation errors
* misc. fixes
-----BEGIN PGP SIGNATURE-----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=qicd
-----END PGP SIGNATURE-----
Merge tag 'for-v5.2' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply
Pull power supply and reset updates from Sebastian Reichel:
"Core:
- Add over-current health state
- Add standard, adaptive and custom charge types
- Add new properties for start/end charge threshold
New Drivers / Hardware:
- UCS1002 Programmable USB Port Power Controller
- Ingenic JZ47xx Battery Fuel Gauge
- AXP20x USB Power: Add AXP813 support
- AT91 poweroff: Add SAM9X60 support
- OLPC battery: Add XO-1.5 and XO-1.75 support
Misc Changes:
- syscon-reboot: support mask property
- AXP288 fuel gauge: Blacklist ACEPC T8/T11. Looks like some vendor
thought it's a good idea to build a desktop system with a fuel
gauge, that slowly "discharges"...
- cpcap-battery: Fix calculation errors
- misc fixes"
* tag 'for-v5.2' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply: (54 commits)
power: supply: olpc_battery: force the le/be casts
power: supply: ucs1002: Fix build error without CONFIG_REGULATOR
power: supply: ucs1002: Fix wrong return value checking
power: supply: Add driver for Microchip UCS1002
dt-bindings: power: supply: Add bindings for Microchip UCS1002
power: supply: core: Add POWER_SUPPLY_HEALTH_OVERCURRENT constant
power: supply: core: fix clang -Wunsequenced
power: supply: core: Add missing documentation for CHARGE_CONTROL_* properties
power: supply: core: Add CHARGE_CONTROL_{START_THRESHOLD,END_THRESHOLD} properties
power: supply: core: Add Standard, Adaptive, and Custom charge types
power: supply: axp288_fuel_gauge: Add ACEPC T8 and T11 mini PCs to the blacklist
power: supply: bq27xxx_battery: Notify also about status changes
power: supply: olpc_battery: Have the framework register sysfs files for us
power: supply: olpc_battery: Add OLPC XO 1.75 support
power: supply: olpc_battery: Avoid using platform_info
power: supply: olpc_battery: Use devm_power_supply_register()
power: supply: olpc_battery: Move priv data to a struct
power: supply: olpc_battery: Use DT to get battery version
x86/platform/olpc: Use a correct version when making up a battery node
x86/platform/olpc: Trivial code move in DT fixup
...
This patch implements the device tree binding changes required for the
PPS ECHO functionality for pps-gpio, that sysfs claims is available
already.
It adds two DT properties for configuring the PPS ECHO functionality.
This patch is provided separated from the rest of the patch per
Documentation/devicetree/bindings/submitting-patches.txt.
This patch was originally written by Lukas Senger as part of a masters
thesis project and modified for inclusion into the linux kernel by Tom
Burkart.
Link: http://lkml.kernel.org/r/20190324043305.6627-3-tom@aussec.com
Signed-off-by: Tom Burkart <tom@aussec.com>
Signed-off-by: Lukas Senger <lukas@fridolin.com>
Acked-by: Rodolfo Giometti <giometti@enneenne.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Cc: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- Document (kerneldoc) core mfd_add_devices() API
- New Drivers
- Add support for Altera SOCFPGA System Manager
- Add support for Maxim MAX77650/77651 PMIC
- Add support for Maxim MAX77663 PMIC
- Add support for ST Multi-Function eXpander (STMFX)
- New Device Support
- Add support for LEDs to Intel Cherry Trail Whiskey Cove PMIC
- Add support for RTC to SAMSUNG Electronics S2MPA01 PMIC
- Add support for SAM9X60 to Atmel HLCDC (High-end LCD Controller)
- Add support for USB X-Powers AXP 8xx PMICs
- Add support for Integrated Sensor Hub (ISH) to ChromeOS EC
- Add support for USB PD Logger to ChromeOS EC
- Add support for AXP223 to X-Powers AXP series PMICs
- Add support for Power Supply to X-Powers AXP 803 PMICs
- Add support for Comet Lake to Intel Low Power Subsystem
- Add support for Fingerprint MCU to ChromeOS EC
- Add support for Touchpad MCU to ChromeOS EC
- Move TI LM3532 support to LED
- New Functionality
- Add/extend DT support; max77650, max77620
- Add support for power-off; max77620
- Add support for clocking; syscon
- Add support for host sleep event; cros_ec
- Fix-ups
- Trivial; Formatting, spelling, etc; Kconfig, sec-core, ab8500-debugfs
- Remove unused functionality; rk808, da9063-*
- SPDX conversion; da9063-*, atmel-*,
- Adapt/add new register definitions; cs47l35-tables, cs47l90-tables, imx6q-iomuxc-gpr
- Fix-up DT bindings; ti-lmu, cirrus,lochnagar
- Simply obtaining driver data; ssbi, t7l66xb, tc6387xb, tc6393xb
- Bug Fixes
- Fix incorrect defined values; max77620, da9063
- Fix device initialisation; twl6040
- Reset device on init; intel-lpss
- Fix build warnings when !OF; sun6i-prcm
- Register OF match tables; tps65912-spi
- Fix DMI matching; intel_quark_i2c_gpio
-----BEGIN PGP SIGNATURE-----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=dTSD
-----END PGP SIGNATURE-----
Merge tag 'mfd-next-5.2' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD updates from Lee Jones:
"Core Framework:
- Document (kerneldoc) core mfd_add_devices() API
New Drivers:
- Altera SOCFPGA System Manager
- Maxim MAX77650/77651 PMIC
- Maxim MAX77663 PMIC
- ST Multi-Function eXpander (STMFX)
New Device Support:
- LEDs support in Intel Cherry Trail Whiskey Cove PMIC
- RTC support in SAMSUNG Electronics S2MPA01 PMIC
- SAM9X60 support in Atmel HLCDC (High-end LCD Controller)
- USB X-Powers AXP 8xx PMICs
- Integrated Sensor Hub (ISH) in ChromeOS EC
- USB PD Logger in ChromeOS EC
- AXP223 in X-Powers AXP series PMICs
- Power Supply in X-Powers AXP 803 PMICs
- Comet Lake in Intel Low Power Subsystem
- Fingerprint MCU in ChromeOS EC
- Touchpad MCU in ChromeOS EC
- Move TI LM3532 support to LED
New Functionality:
- max77650, max77620: Add/extend DT support
- max77620 power-off
- syscon clocking
- croc_ec host sleep event
Fix-ups:
- Trivial; Formatting, spelling, etc; Kconfig, sec-core, ab8500-debugfs
- Remove unused functionality; rk808, da9063-*
- SPDX conversion; da9063-*, atmel-*,
- Adapt/add new register definitions; cs47l35-tables, cs47l90-tables, imx6q-iomuxc-gpr
- Fix-up DT bindings; ti-lmu, cirrus,lochnagar
- Simply obtaining driver data; ssbi, t7l66xb, tc6387xb, tc6393xb
Bug Fixes:
- Fix incorrect defined values; max77620, da9063
- Fix device initialisation; twl6040
- Reset device on init; intel-lpss
- Fix build warnings when !OF; sun6i-prcm
- Register OF match tables; tps65912-spi
- Fix DMI matching; intel_quark_i2c_gpio"
* tag 'mfd-next-5.2' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (65 commits)
mfd: Use dev_get_drvdata() directly
mfd: cros_ec: Instantiate properly CrOS Touchpad MCU device
mfd: cros_ec: Instantiate properly CrOS FP MCU device
mfd: cros_ec: Update the EC feature codes
mfd: intel-lpss: Add Intel Comet Lake PCI IDs
mfd: lochnagar: Add links to binding docs for sound and hwmon
mfd: ab8500-debugfs: Fix a typo ("deubgfs")
mfd: imx6sx: Add MQS register definition for iomuxc gpr
dt-bindings: mfd: LMU: Fix lm3632 dt binding example
mfd: intel_quark_i2c_gpio: Adjust IOT2000 matching
mfd: da9063: Fix OTP control register names to match datasheets for DA9063/63L
mfd: tps65912-spi: Add missing of table registration
mfd: axp20x: Add USB power supply mfd cell to AXP803
mfd: sun6i-prcm: Fix build warning for non-OF configurations
mfd: intel-lpss: Set the device in reset state when init
platform/chrome: Add support for v1 of host sleep event
mfd: cros_ec: Add host_sleep_event_v1 command
mfd: cros_ec: Instantiate the CrOS USB PD logger driver
mfd: cs47l90: Make DAC_AEC_CONTROL_2 readable
mfd: cs47l35: Make DAC_AEC_CONTROL_2 readable
...
Add a new compatible for thermal founding on PX30 SoCs.
Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
qcs404 uses v1 of the TSENS IP block. Create a fallback DT property
"qcom,tsens-v1" to gather common code
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Add new backlight bindings for the TI LM3630A dual-string white LED.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Pavel Machek <pavel@ucw.cz>
Acked-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Lochnagar is an evaluation and development board for Cirrus
Logic Smart CODEC and Amp devices. It allows the connection of
most Cirrus Logic devices on mini-cards, as well as allowing
connection of various application processor systems to provide a
full evaluation platform. This driver supports the board
controller chip on the Lochnagar board.
Add links to the binding documents for the new sound and hardware
monitor parts of the driver.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Fix the lm3632 dt binding examples as the LCM enable GPIOs
are defined as enable GPIOs per the regulator/lm363x-regulator.txt
bindings document.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add new compatible string for the HLCD controller on SAM9X60 SoC.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
STM32 system configuration controller registers needs to be clocked.
Document clock support on stm32-syscon.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
-----BEGIN PGP SIGNATURE-----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=55X1
-----END PGP SIGNATURE-----
Merge branches 'ib-mfd-arm-leds-5.2', 'ib-mfd-gpio-input-leds-power-5.2', 'ib-mfd-pinctrl-5.2-2' and 'ib-mfd-regulator-5.2', tag 'ib-mfd-arm-net-5.2' into ibs-for-mfd-merged
Immutable branch between MFD, ARM and Net due for the 5.2 merge window
Add OC HW throttle configuration for soctherm in DT.
It is used to describe the OCx throttle events.
Signed-off-by: Wei Ni <wni@nvidia.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Add optional property "nvidia,thermtrips".
If present, these trips will be used as HW shutdown trips,
and critical trips will be used as SW shutdown trips.
Signed-off-by: Wei Ni <wni@nvidia.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
- Move IRQ register address computation inside macros (Kishon Vijay
Abraham I)
- Separate legacy IRQ and MSI configuration (Kishon Vijay Abraham I)
- Use hwirq, not virq, to get MSI IRQ number offset (Kishon Vijay Abraham
I)
- Squash ks_pcie_handle_msi_irq() into ks_pcie_msi_irq_handler() (Kishon
Vijay Abraham I)
- Add dwc support for platforms with custom MSI controllers (Kishon Vijay
Abraham I)
- Add keystone-specific MSI controller (Kishon Vijay Abraham I)
- Remove dwc host_ops previously used for keystone-specific MSI (Kishon
Vijay Abraham I)
- Skip dwc default MSI init if platform has custom MSI controller (Kishon
Vijay Abraham I)
- Implement .start_link() and .stop_link() for keystone endpoint support
(Kishon Vijay Abraham I)
- Add keystone "reg-names" DT binding (Kishon Vijay Abraham I)
- Squash ks_pcie_dw_host_init() into ks_pcie_add_pcie_port() (Kishon
Vijay Abraham I)
- Get keystone register resources from DT by name, not index (Kishon
Vijay Abraham I)
- Get DT resources in .probe() to prepare for endpoint support (Kishon
Vijay Abraham I)
- Add "ti,syscon-pcie-mode" DT property for PCIe mode configuration
(Kishon Vijay Abraham I)
- Explicitly set keystone to host mode (Kishon Vijay Abraham I)
- Document DT "atu" reg-names requirement for DesignWare core >= 4.80
(Kishon Vijay Abraham I)
- Enable dwc iATU unroll for endpoint mode as well as host mode (Kishon
Vijay Abraham I)
- Add dwc "version" to identify core >= 4.80 for ATU programming (Kishon
Vijay Abraham I)
- Don't build ARM32-specific keystone code on ARM64 (Kishon Vijay Abraham
I)
- Add DT binding for keystone PCIe RC in AM654 SoC (Kishon Vijay Abraham
I)
- Add keystone support for AM654 SoC PCIe RC (Kishon Vijay Abraham I)
- Reset keystone PHYs before enabling them (Kishon Vijay Abraham I)
- Make of_pci_get_max_link_speed() available to endpoint drivers as well
as host drivers (Kishon Vijay Abraham I)
- Add keystone support for DT "max-link-speed" property (Kishon Vijay
Abraham I)
- Add endpoint library support for BAR buffer alignment (Kishon Vijay
Abraham I)
- Make all dw_pcie_ep_ops structs const (Kishon Vijay Abraham I)
- Fix fencepost error in dw_pcie_ep_find_capability() (Kishon Vijay
Abraham I)
- Add dwc hooks for dbi/dbi2 that share the same address space (Kishon
Vijay Abraham I)
- Add keystone support for TI AM654x in endpoint mode (Kishon Vijay
Abraham I)
- Configure designware endpoints to advertise smallest resizable BAR
(1MB) (Kishon Vijay Abraham I)
- Align designware endpoint ATU windows for raising MSIs (Kishon Vijay
Abraham I)
- Add endpoint test support for TI AM654x (Kishon Vijay Abraham I)
- Fix endpoint test test_reg_bar issue (Kishon Vijay Abraham I)
* remotes/lorenzo/pci/keystone:
misc: pci_endpoint_test: Fix test_reg_bar to be updated in pci_endpoint_test
misc: pci_endpoint_test: Add support to test PCI EP in AM654x
PCI: designware-ep: Use aligned ATU window for raising MSI interrupts
PCI: designware-ep: Configure Resizable BAR cap to advertise the smallest size
PCI: keystone: Add support for PCIe EP in AM654x Platforms
dt-bindings: PCI: Add PCI EP DT binding documentation for AM654
PCI: dwc: Add callbacks for accessing dbi2 address space
PCI: dwc: Fix dw_pcie_ep_find_capability() to return correct capability offset
PCI: dwc: Add const qualifier to struct dw_pcie_ep_ops
PCI: endpoint: Add support to specify alignment for buffers allocated to BARs
PCI: keystone: Add support to set the max link speed from DT
PCI: OF: Allow of_pci_get_max_link_speed() to be used by PCI Endpoint drivers
PCI: keystone: Invoke phy_reset() API before enabling PHY
PCI: keystone: Add support for PCIe RC in AM654x Platforms
dt-bindings: PCI: Add PCI RC DT binding documentation for AM654
PCI: keystone: Prevent ARM32 specific code to be compiled for ARM64
PCI: dwc: Fix ATU identification for designware version >= 4.80
PCI: dwc: Enable iATU unroll for endpoint too
dt-bindings: PCI: Document "atu" reg-names
PCI: keystone: Explicitly set the PCIe mode
dt-bindings: PCI: Add dt-binding to configure PCIe mode
PCI: keystone: Move resources initialization to prepare for EP support
PCI: keystone: Use platform_get_resource_byname() to get memory resources
PCI: keystone: Perform host initialization in a single function
dt-bindings: PCI: keystone: Add "reg-names" binding information
PCI: keystone: Cleanup error_irq configuration
PCI: keystone: Add start_link()/stop_link() dw_pcie_ops
PCI: dwc: Remove default MSI initialization for platform specific MSI chips
PCI: dwc: Remove Keystone specific dw_pcie_host_ops
PCI: keystone: Use Keystone specific msi_irq_chip
PCI: dwc: Add support to use non default msi_irq_chip
PCI: keystone: Cleanup ks_pcie_msi_irq_handler()
PCI: keystone: Use hwirq to get the MSI IRQ number offset
PCI: keystone: Add separate functions for configuring MSI and legacy interrupt
PCI: keystone: Cleanup interrupt related macros
# Conflicts:
# drivers/pci/controller/dwc/pcie-designware.h
Pull input updates from Dmitry Torokhov:
"A few new drivers:
- driver for Azoteq IQS550/572/525 touch controllers
- driver for Microchip AT42QT1050 keys
- driver for GPIO controllable vibrators
- support for GT5663 in Goodix driver
... along with miscellaneous driver fixes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: libps2 - mark expected switch fall-through
Input: qt1050 - add Microchip AT42QT1050 support
Input: add support for Azoteq IQS550/572/525
Input: add a driver for GPIO controllable vibrators
Input: synaptics-rmi4 - fix enum_fmt
Input: synaptics-rmi4 - fill initial format
HID: input: add mapping for KEY_KBD_LAYOUT_NEXT
Input: add KEY_KBD_LAYOUT_NEXT
Input: hyperv-keyboard - add module description
Input: olpc_apsp - depend on ARCH_MMP
Input: sun4i-a10-lradc-keys - add support for A83T
Input: snvs_pwrkey - use dev_pm_set_wake_irq() to simplify code
Input: lpc32xx-key - add clocks property and fix DT binding example
Input: i8042 - signal wakeup from atkbd/psmouse
Input: goodix - add GT5663 CTP support
Input: goodix - add regulators suppot
Input: evdev - use struct_size() in kzalloc() and vzalloc()
Input: edt-ft5x06 - convert to use SPDX identifier
Input: edt-ft5x06 - enable ACPI enumeration
Pull networking fixes from David Miller:
"Fixes all over:
1) Netdev refcnt leak in nf_flow_table, from Taehee Yoo.
2) Fix RCU usage in nf_tables, from Florian Westphal.
3) Fix DSA build when NET_DSA_TAG_BRCM_PREPEND is not set, from Yue
Haibing.
4) Add missing page read/write ops to realtek driver, from Heiner
Kallweit.
5) Endianness fix in qrtr code, from Nicholas Mc Guire.
6) Fix various bugs in DSA_SKB_* macros, from Vladimir Oltean.
7) Several BPF documentation cures, from Quentin Monnet.
8) Fix undefined behavior in narrow load handling of BPF verifier,
from Krzesimir Nowak.
9) DMA ops crash in SGI Seeq driver due to not set netdev parent
device pointer, from Thomas Bogendoerfer.
10) Flow dissector has to disable preemption when invoking BPF
program, from Eric Dumazet"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (48 commits)
net: ethernet: stmmac: dwmac-sun8i: enable support of unicast filtering
net: ethernet: ti: netcp_ethss: fix build
flow_dissector: disable preemption around BPF calls
bonding: fix arp_validate toggling in active-backup mode
net: meson: fixup g12a glue ephy id
net: phy: realtek: Replace phy functions with non-locked version in rtl8211e_config_init()
net: seeq: fix crash caused by not set dev.parent
of_net: Fix missing of_find_device_by_node ref count drop
net: mvpp2: cls: Add missing NETIF_F_NTUPLE flag
bpf: fix undefined behavior in narrow load handling
libbpf: detect supported kernel BTF features and sanitize BTF
selftests: bpf: Add files generated after build to .gitignore
tools: bpf: synchronise BPF UAPI header with tools
bpf: fix minor issues in documentation for BPF helpers.
bpf: fix recurring typo in documentation for BPF helpers
bpf: fix script for generating man page on BPF helpers
bpf: add various test cases for backward jumps
net: dccp : proto: remove Unneeded variable "err"
net: dsa: Remove the now unused DSA_SKB_CB_COPY() macro
net: dsa: Remove dangerous DSA_SKB_CLONE() macro
...
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.14 (GNU/Linux)
iEYEABECAAYFAlzZRp0ACgkQ+iyteGJfRsq1WQCfaR8jQjujN1bGWghnSWbTr01X
O3cAn3RmJWiEtI0zmmMcRQBna8nj4cHJ
=PuHw
-----END PGP SIGNATURE-----
Merge tag 'linux-watchdog-5.2-rc1' of git://www.linux-watchdog.org/linux-watchdog
Pull watchdog updates from Wim Van Sebroeck:
- a new watchdog driver for the ROHM BD70528 watchdog block
- a new watchdog driver for the i.MX system controller watchdog
- conversions to use device managed functions and other improvements
- refactor watchdog_init_timeout
- make watchdog core configurable as module
- pretimeout governors improvements
- a lot of other fixes
* tag 'linux-watchdog-5.2-rc1' of git://www.linux-watchdog.org/linux-watchdog: (114 commits)
watchdog: Enforce that at least one pretimeout governor is enabled
watchdog: stm32: add dynamic prescaler support
watchdog: Improve Kconfig entry ordering and dependencies
watchdog: npcm: Enable modular builds
watchdog: Make watchdog core configurable as module
watchdog: Move pretimeout governor configuration up
watchdog: Use depends instead of select for pretimeout governors
watchdog: rtd119x: drop unused module.h include
watchdog: intel_scu: make it explicitly non-modular
watchdog: coh901327: make it explicitly non-modular
watchdog: ziirave_wdt: drop warning after calling watchdog_init_timeout
watchdog: xen_wdt: drop warning after calling watchdog_init_timeout
watchdog: stm32_iwdg: drop warning after calling watchdog_init_timeout
watchdog: st_lpc_wdt: drop warning after calling watchdog_init_timeout
watchdog: sp5100_tco: drop warning after calling watchdog_init_timeout
watchdog: renesas_wdt: drop warning after calling watchdog_init_timeout
watchdog: nic7018_wdt: drop warning after calling watchdog_init_timeout
watchdog: ni903x_wdt: drop warning after calling watchdog_init_timeout
watchdog: imx_sc_wdt: drop warning after calling watchdog_init_timeout
watchdog: i6300esb: drop warning after calling watchdog_init_timeout
...
MTD core changes:
- New AFS partition parser
- Update MAINTAINERS entry
- Use of fall-throughs markers
NAND core changes:
- Support having the bad block markers in either the first, second or
last page of a block. The combination of all three location is now
possible.
- Constification of NAND_OP_PARSER(_PATTERN) elements.
- Generic NAND DT bindings changed to yaml format (can be used to
check the proposed bindings. First platform to be fully supported:
sunxi.
- Stopped using several legacy hooks.
- Preparation to use the generic NAND layer with the addition of
several helpers and the removal of the struct nand_chip from generic
functions.
- Kconfig cleanup to prepare the introduction of external ECC engines
support.
- Fallthrough comments.
- Introduction of the SPI-mem dirmap API for SPI-NAND devices.
Raw NAND controller drivers changes:
- nandsim:
* Switch to ->exec-op().
- meson:
* Misc cleanups and fixes.
* New OOB layout.
- Sunxi:
* A23/A33 NAND DMA support.
- Ingenic:
* Full reorganization and cleanup.
* Clear separation between NAND controller and ECC engine.
* Support JZ4740 an JZ4725B.
- Denali:
* Clear controller/chip separation.
* ->exec_op() migration.
* Various cleanups.
- fsl_elbc:
* Enable software ECC support.
- Atmel:
* Sam9x60 support.
- GPMI:
* Introduce the GPMI_IS_MXS() macro.
- Various trivial/spelling/coding style fixes.
SPI NOR core changes:
- Print all JEDEC ID bytes on error
- Fix comment of spi_nor_find_best_erase_type()
- Add region locking flags for s25fl512s
SPI NOR controller drivers changes:
- intel-spi:
* Avoid crossing 4K address boundary on read/write
* Add support for Intel Comet Lake SPI serial flash
-----BEGIN PGP SIGNATURE-----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=HXap
-----END PGP SIGNATURE-----
Merge tag 'mtd/for-5.2' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/mtd/linux
Pull MTD updates from Richard Weinberger:
"MTD core changes:
- New AFS partition parser
- Update MAINTAINERS entry
- Use of fall-throughs markers
NAND core changes:
- Support having the bad block markers in either the first, second or
last page of a block. The combination of all three location is now
possible.
- Constification of NAND_OP_PARSER(_PATTERN) elements.
- Generic NAND DT bindings changed to yaml format (can be used to
check the proposed bindings. First platform to be fully supported:
sunxi.
- Stopped using several legacy hooks.
- Preparation to use the generic NAND layer with the addition of
several helpers and the removal of the struct nand_chip from
generic functions.
- Kconfig cleanup to prepare the introduction of external ECC engines
support.
- Fallthrough comments.
- Introduction of the SPI-mem dirmap API for SPI-NAND devices.
Raw NAND controller drivers changes:
- nandsim:
- Switch to ->exec-op().
- meson:
- Misc cleanups and fixes.
- New OOB layout.
- Sunxi:
- A23/A33 NAND DMA support.
- Ingenic:
- Full reorganization and cleanup.
- Clear separation between NAND controller and ECC engine.
- Support JZ4740 an JZ4725B.
- Denali:
- Clear controller/chip separation.
- ->exec_op() migration.
- Various cleanups.
- fsl_elbc:
- Enable software ECC support.
- Atmel:
- Sam9x60 support.
- GPMI:
- Introduce the GPMI_IS_MXS() macro.
- Various trivial/spelling/coding style fixes.
SPI NOR core changes:
- Print all JEDEC ID bytes on error
- Fix comment of spi_nor_find_best_erase_type()
- Add region locking flags for s25fl512s
SPI NOR controller drivers changes:
- intel-spi:
- Avoid crossing 4K address boundary on read/write
- Add support for Intel Comet Lake SPI serial flash"
* tag 'mtd/for-5.2' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/mtd/linux: (120 commits)
mtd: part: fix incorrect format specifier for an unsigned long long
mtd: lpddr_cmds: Mark expected switch fall-through
mtd: phram: Mark expected switch fall-throughs
mtd: cfi_cmdset_0002: Mark expected switch fall-throughs
mtd: cfi_util: mark expected switch fall-throughs
MAINTAINERS: MTD Git repository is hosted on kernel.org
MAINTAINERS: Update jffs2 entry
mtd: afs: add v2 partition parsing
mtd: afs: factor the IIS read into partition parser
mtd: afs: factor footer parsing into the v1 part parsing
mtd: factor out v1 partition parsing
mtd: afs: simplify partition detection
mtd: afs: simplify partition parsing
mtd: partitions: Add OF support to AFS partitions
mtd: partitions: Add AFS partitions DT bindings
mtd: afs: Move AFS partition parser to parsers subdir
mtd: maps: Make uclinux_ram_map static
mtd: maps: Allow MTD_PHYSMAP with MTD_RAM
MAINTAINERS: Add myself as MTD maintainer
MAINTAINERS: Remove my name from the MTD and NAND entries
...
Core changes:
- The gpiolib MMIO driver has been enhanced to handle two direction
registers, i.e. one register to set lines as input and one register
to set lines as output. It turns out some silicon engineer thinks
the ability to configure a line as input and output at the same
time makes sense, this can be debated but includes a lot of analog
electronics reasoning, and the registers are there and need to
be handled consistently. Unsurprisingly, we enforce the lines to
be either inputs or outputs in such schemes.
- Send in the proper argument value to .set_config() dispatched to
the pin control subsystem. Nobody used it before, now someone
does, so fix it to work as expected.
- The ACPI gpiolib portions can now handle pin bias setting (pull up
or pull down). This has been in the ACPI spec for years and we
finally have it properly integrated with Linux GPIOs. It was based
on an observation from Andy Schevchenko that Thomas Petazzoni's
changes to the core for biasing the PCA950x GPIO expander actually
happen to fit hand-in-glove with what the ACPI core needed.
Such nice synergies happen sometimes.
New drivers:
- A new driver for the Mellanox BlueField GPIO controller. This is
using 64bit MMIO registers and can configure lines as inputs
and outputs at the same time and after improving the MMIO library
we handle it just fine. Interesting.
- A new IXP4xx proper gpiochip driver with hierarchical interrupts
should be coming in from the ARM SoC tree as well.
Driver enhancements:
- The PCA053x driver handles the CAT9554 GPIO expander.
- The PCA053x driver handles the NXP PCAL6416 GPIO expander.
- Wake-up support on PCA053x GPIO lines.
- OMAP now does a nice asynchronous IRQ handling on wake-ups by
letting everything wake up on edges, and this makes runtime PM
work as expected too.
Misc:
- Several cleanups such as devres fixes.
- Get rid of some languager comstructs that cause problems when
compiling with LLVMs clang.
- Documentation review and update.
-----BEGIN PGP SIGNATURE-----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=rhto
-----END PGP SIGNATURE-----
Merge tag 'gpio-v5.2-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull gpio updates from Linus Walleij:
"This is the bulk of the GPIO changes for the v5.2 kernel cycle. A bit
later than usual because I was ironing out my own mistakes. I'm
holding some stuff back for the next kernel as a result, and this
should be a healthy and well tested batch.
Core changes:
- The gpiolib MMIO driver has been enhanced to handle two direction
registers, i.e. one register to set lines as input and one register
to set lines as output. It turns out some silicon engineer thinks
the ability to configure a line as input and output at the same
time makes sense, this can be debated but includes a lot of analog
electronics reasoning, and the registers are there and need to be
handled consistently. Unsurprisingly, we enforce the lines to be
either inputs or outputs in such schemes.
- Send in the proper argument value to .set_config() dispatched to
the pin control subsystem. Nobody used it before, now someone does,
so fix it to work as expected.
- The ACPI gpiolib portions can now handle pin bias setting (pull up
or pull down). This has been in the ACPI spec for years and we
finally have it properly integrated with Linux GPIOs. It was based
on an observation from Andy Schevchenko that Thomas Petazzoni's
changes to the core for biasing the PCA950x GPIO expander actually
happen to fit hand-in-glove with what the ACPI core needed. Such
nice synergies happen sometimes.
New drivers:
- A new driver for the Mellanox BlueField GPIO controller. This is
using 64bit MMIO registers and can configure lines as inputs and
outputs at the same time and after improving the MMIO library we
handle it just fine. Interesting.
- A new IXP4xx proper gpiochip driver with hierarchical interrupts
should be coming in from the ARM SoC tree as well.
Driver enhancements:
- The PCA053x driver handles the CAT9554 GPIO expander.
- The PCA053x driver handles the NXP PCAL6416 GPIO expander.
- Wake-up support on PCA053x GPIO lines.
- OMAP now does a nice asynchronous IRQ handling on wake-ups by
letting everything wake up on edges, and this makes runtime PM work
as expected too.
Misc:
- Several cleanups such as devres fixes.
- Get rid of some languager comstructs that cause problems when
compiling with LLVMs clang.
- Documentation review and update"
* tag 'gpio-v5.2-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (85 commits)
gpio: Update documentation
docs: gpio: convert docs to ReST and rename to *.rst
gpio: sch: Remove write-only core_base
gpio: pxa: Make two symbols static
gpiolib: acpi: Respect pin bias setting
gpiolib: acpi: Add acpi_gpio_update_gpiod_lookup_flags() helper
gpiolib: acpi: Set pin value, based on bias, more accurately
gpiolib: acpi: Change type of dflags
gpiolib: Introduce GPIO_LOOKUP_FLAGS_DEFAULT
gpiolib: Make use of enum gpio_lookup_flags consistent
gpiolib: Indent entry values of enum gpio_lookup_flags
gpio: pca953x: add support for pca6416
dt-bindings: gpio: pca953x: document the nxp,pca6416
gpio: pca953x: add pcal6416 to the of_device_id table
gpio: gpio-omap: Remove conditional pm_runtime handling for GPIO interrupts
gpio: gpio-omap: configure edge detection for level IRQs for idle wakeup
tracing: stop making gpio tracing configurable
gpio: pca953x: Configure wake-up path when wake-up is enabled
gpio: of: Optimize quirk checks
gpio: mmio: Drop bgpio_dir_inverted
...
In commit 687e3d5550 ("dt-bindings: doc: reflect new NVMEM
of_get_mac_address behaviour") I've kept or added references to Linux
of_get_mac_address API which is unwanted so this patch fixes that by
removing those references.
Fixes: 687e3d5550 ("dt-bindings: doc: reflect new NVMEM of_get_mac_address behaviour")
Suggested-by: Rob Herring <robh@kernel.org>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nothing out of the ordinary this cycle. The bulk of this is a collection
of fixes for existing drivers and some cleanups. There's one new driver
for i.MX SoCs and addition of support for some new variants to existing
drivers.
-----BEGIN PGP SIGNATURE-----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=3p6h
-----END PGP SIGNATURE-----
Merge tag 'pwm/for-5.2-rc1' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm
Pull pwm updates from Thierry Reding:
"Nothing out of the ordinary this cycle.
The bulk of this is a collection of fixes for existing drivers and
some cleanups. There's one new driver for i.MX SoCs and addition of
support for some new variants to existing drivers"
* tag 'pwm/for-5.2-rc1' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm:
pwm: meson: Add clock source configuration for Meson G12A
dt-bindings: pwm: Update bindings for the Meson G12A Family
pwm: samsung: Don't uses devm_*() functions in ->request()
pwm: Clear chip_data in pwm_put()
pwm: Add i.MX TPM PWM driver support
dt-bindings: pwm: Add i.MX TPM PWM binding
pwm: imx27: Use devm_platform_ioremap_resource() to simplify code
pwm: meson: Use the spin-lock only to protect register modifications
pwm: meson: Don't disable PWM when setting duty repeatedly
pwm: meson: Consider 128 a valid pre-divider
pwm: sysfs: fix typo "its" -> "it's"
pwm: tiehrpwm: Enable compilation for ARCH_K3
dt-bindings: pwm: tiehrpwm: Add TI AM654 SoC specific compatible
pwm: tiehrpwm: Update shadow register for disabling PWMs
pwm: img: Turn final 'else if' into 'else' in img_pwm_config
pwm: Fix deadlock warning when removing PWM device
