DSP2 on the WM8958 has a default ROM which provides a multi-band
compressor for enhanced performance on mobile devices but can also
support runtime download of alternative firmware. In preparation for
more exploiting this functionality refactor the code to split the
handling of DSP2 into a separate file.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
The first WM8958 revision requires similar treatment.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Without this fix the driver won't instantiate properly on relevant
devices.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Cc: stable@kernel.org
Without this fix the driver won't instantiate properly on relevant
devices.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Cc: stable@kernel.org
The patch 'ASoC: WM8994: Improve Playback Robustness' did not handle
this case properly.
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Ensure that the ADCs are provided with a clock as the previous patch
"ASoC: WM8994: Improve playback robustness" did not handle this case
properly.
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org
Since we began using the late clock disable functionality, ensure that
we don't disable the clock if any of the ADC or DAC paths are still
enabled. This happens when we have simultaneous playback and recording.
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org
The default WM8958 jack detection handler implements a full set of buttons
and also support for video detection. Support for multi-button jacks is
fairly system specific and will usually require some tuning for headsets
so simplify the implementation to only report a simple short to ground
button, leaving multi-button headsets to be handled by system specific
code.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
The WM8958 has a different microphone bias architecture to WM8994 so needs
different configuration to WM8994. Support this in platform data.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Allow direct routing of the WM8958 microphone detection signal to a GPIO
to be used, saving the need to demux the interrupt.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
On WM8994 revision D and earlier ensure proper playback robustness
as some rare use cases can trigger issues.
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org
Ensure that on disabling certain registers such as AIF1DAC1L,
AIF1DAC1R etc. the AIF1CLK and AIF2CLK remain enabled. Similarly
when enabling those registers, AIF1CLK and AIF2CLK will remain
disabled.
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org
On WM8994 revision D and earlier ensure optimal sequencing with
simultaneous usage of AIF1 and AIF2 by tying the signals together
so if paths through both are connected the streams are started
simultaneously.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Cc: stable@kernel.org
Due to the different routing for AIF1 and AIF2 we weren't using a
single widget to represent the ADCDAT signal. For consistency add
one.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Cc: stable@kernel.org
fix wrong value in wm8994_set_tristate func. when updating reg bits,
it should use "value", not "reg".
Signed-off-by: Qiao Zhou <zhouqiao@marvell.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org
Add jack detection interrupt trace to Wolfson CODEC drivers.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
The compiler really ought to have been warning about unreferenced
variables...
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
The oversampling rate of the DAC and ADC can be controlled to optimise
for either low power consumption or maximum performance.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Uk Kim <w0806.kim@samsung.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The WM8994 supports mono signals - enable this in the driver. With DSP
mode an automatic data channel selector is available, activate this
when in mono mode.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
When we disable the WM8994 FLL code path sharing means that we end up
writing out a configuration. Currently this is the currently active
input and output frequency (which causes snd_soc_update_bits() to
suppress actual writes both immediately and in the common case where
we reenable the same configuration later) but we allow machine drivers
to pass through a source of zero. Since the register values written
are one less than the source constants this causes corruption of other
bitfields in the register.
Fix this by using the most recently configured FLL source when none is
provided.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Cc: stable@kernel.org
Update some of the default configuration for the device to improve
the performance.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
The paramters of the WM8958 multiband compressor can be tuned by the
user for their system using a graphical configuration tool on the host.
Allow the user to specify a set of such paramters in platform data and
select between them at runtime.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
We need a post notification as we need to shut down the MBC after the
data stops flowing rather than before.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
This allows us to communicate our power management state back to the
parent device, allowing it to do a full power down when the device is
idle.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
The WM8994 and WM8958 register map is relatively sparse so benefits
from compression. The rbtree compression gives better results than
LZO for both memory and CPU consumption on a map as sparse as this.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
In the process we convert the driver to read registers one at a time
when initialising the cache. This has the effect of working around
limitations in the sizes of I2C transactions which can be done by some
CPUs. Due to the sparseness of the register map the overhead from this
should be minimual unless I2C transactions are very expensive to start.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
The WM8958 contains an advanced accessory detection feature which allows
detection of up to seven different impedence levels on the microphone
bias output, including detection of video outputs. Since some of the
more involved accessory interfaces may involve noticable interactions
with external components a simple detection scheme is provided by
default with the option to provide custom handling of accessory detect.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
The WM8958 features a multi-band compressor which can be enabled on
any of the AIF inputs. The MBC allows different gains to be applied to
differnt audio bands, providing an improvement in perceived loudness
of the signal by avoiding overdriving the output transducers. This
patch enables support for the MBC.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Additional audio routing options are available on the WM8958 audio
interface 3. Add support for these.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
The WM8958 is a WM8994 derivative. This patch merely ensures that some
revision specific configuration for WM8994 is not enabled on WM8994,
additional patches will add support for the new features introduced on
the WM8958.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
They went AWOL during the multi-component merge.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
There is no need to include soc-dapm.h since soc.h includes it.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Makes the WM8994 driver file itself substantially smaller.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Allow the application to choose if the ADC data presented on the left
and right channels is sourced from the internal left or right channel.
This allows a mono recording to be presented as stereo on the external
bus.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
