New action to decrement TTL instead of setting it to a fixed value.
This action will decrement the TTL and, in case of expired TTL, drop it
or execute an action passed via a nested attribute.
The default TTL expired action is to drop the packet.
Supports both IPv4 and IPv6 via the ttl and hop_limit fields, respectively.
Tested with a corresponding change in the userspace:
# ovs-dpctl dump-flows
in_port(2),eth(),eth_type(0x0800), packets:0, bytes:0, used:never, actions:dec_ttl{ttl<=1 action:(drop)},1
in_port(1),eth(),eth_type(0x0800), packets:0, bytes:0, used:never, actions:dec_ttl{ttl<=1 action:(drop)},2
in_port(1),eth(),eth_type(0x0806), packets:0, bytes:0, used:never, actions:2
in_port(2),eth(),eth_type(0x0806), packets:0, bytes:0, used:never, actions:1
# ping -c1 192.168.0.2 -t 42
IP (tos 0x0, ttl 41, id 61647, offset 0, flags [DF], proto ICMP (1), length 84)
192.168.0.1 > 192.168.0.2: ICMP echo request, id 386, seq 1, length 64
# ping -c1 192.168.0.2 -t 120
IP (tos 0x0, ttl 119, id 62070, offset 0, flags [DF], proto ICMP (1), length 84)
192.168.0.1 > 192.168.0.2: ICMP echo request, id 388, seq 1, length 64
# ping -c1 192.168.0.2 -t 1
#
Co-developed-by: Bindiya Kurle <bindiyakurle@gmail.com>
Signed-off-by: Bindiya Kurle <bindiyakurle@gmail.com>
Signed-off-by: Matteo Croce <mcroce@redhat.com>
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a straight-forward conversion case for the new function, keeping
the flow of the existing code as intact as possible.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The existing PUSH MPLS action inserts MPLS header between ethernet header
and the IP header. Though this behaviour is fine for L3 VPN where an IP
packet is encapsulated inside a MPLS tunnel, it does not suffice the L2
VPN (l2 tunnelling) requirements. In L2 VPN the MPLS header should
encapsulate the ethernet packet.
The new mpls action ADD_MPLS inserts MPLS header at the start of the
packet or at the start of the l3 header depending on the value of l3 tunnel
flag in the ADD_MPLS arguments.
POP_MPLS action is extended to support ethertype 0x6558.
Signed-off-by: Martin Varghese <martin.varghese@nokia.com>
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace all the occurrences of FIELD_SIZEOF() with sizeof_field() except
at places where these are defined. Later patches will remove the unused
definition of FIELD_SIZEOF().
This patch is generated using following script:
EXCLUDE_FILES="include/linux/stddef.h|include/linux/kernel.h"
git grep -l -e "\bFIELD_SIZEOF\b" | while read file;
do
if [[ "$file" =~ $EXCLUDE_FILES ]]; then
continue
fi
sed -i -e 's/\bFIELD_SIZEOF\b/sizeof_field/g' $file;
done
Signed-off-by: Pankaj Bharadiya <pankaj.laxminarayan.bharadiya@intel.com>
Link: https://lore.kernel.org/r/20190924105839.110713-3-pankaj.laxminarayan.bharadiya@intel.com
Co-developed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: David Miller <davem@davemloft.net> # for net
The skb_mpls_push was not updating ethertype of an ethernet packet if
the packet was originally received from a non ARPHRD_ETHER device.
In the below OVS data path flow, since the device corresponding to
port 7 is an l3 device (ARPHRD_NONE) the skb_mpls_push function does
not update the ethertype of the packet even though the previous
push_eth action had added an ethernet header to the packet.
recirc_id(0),in_port(7),eth_type(0x0800),ipv4(tos=0/0xfc,ttl=64,frag=no),
actions:push_eth(src=00:00:00:00:00:00,dst=00:00:00:00:00:00),
push_mpls(label=13,tc=0,ttl=64,bos=1,eth_type=0x8847),4
Fixes: 8822e270d6 ("net: core: move push MPLS functionality from OvS to core helper")
Signed-off-by: Martin Varghese <martin.varghese@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The openvswitch module shares a common conntrack and NAT infrastructure
exposed via netfilter. It's possible that a packet needs both SNAT and
DNAT manipulation, due to e.g. tuple collision. Netfilter can support
this because it runs through the NAT table twice - once on ingress and
again after egress. The openvswitch module doesn't have such capability.
Like netfilter hook infrastructure, we should run through NAT twice to
keep the symmetry.
Fixes: 05752523e5 ("openvswitch: Interface with NAT.")
Signed-off-by: Aaron Conole <aconole@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The skb_mpls_pop was not updating ethertype of an ethernet packet if the
packet was originally received from a non ARPHRD_ETHER device.
In the below OVS data path flow, since the device corresponding to port 7
is an l3 device (ARPHRD_NONE) the skb_mpls_pop function does not update
the ethertype of the packet even though the previous push_eth action had
added an ethernet header to the packet.
recirc_id(0),in_port(7),eth_type(0x8847),
mpls(label=12/0xfffff,tc=0/0,ttl=0/0x0,bos=1/1),
actions:push_eth(src=00:00:00:00:00:00,dst=00:00:00:00:00:00),
pop_mpls(eth_type=0x800),4
Fixes: ed246cee09 ("net: core: move pop MPLS functionality from OvS to core helper")
Signed-off-by: Martin Varghese <martin.varghese@nokia.com>
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
If we can't build the flow del notification, we can simply delete
the flow, no need to crash the kernel. Still keep a WARN_ON to
preserve debuggability.
Note: the BUG_ON() predates the Fixes tag, but this change
can be applied only after the mentioned commit.
v1 -> v2:
- do not leak an skb on error
Fixes: aed067783e ("openvswitch: Minimize ovs_flow_cmd_del critical section.")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All the callers of ovs_flow_cmd_build_info() already deal with
error return code correctly, so we can handle the error condition
in a more gracefull way. Still dump a warning to preserve
debuggability.
v1 -> v2:
- clarify the commit message
- clean the skb and report the error (DaveM)
Fixes: ccb1352e76 ("net: Add Open vSwitch kernel components.")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When user-space sets the OVS_UFID_F_OMIT_* flags, and the relevant
flow has no UFID, we can exceed the computed size, as
ovs_nla_put_identifier() will always dump an OVS_FLOW_ATTR_KEY
attribute.
Take the above in account when computing the flow command message
size.
Fixes: 74ed7ab926 ("openvswitch: Add support for unique flow IDs.")
Reported-by: Qi Jun Ding <qding@redhat.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The nla_put_u16/nla_put_u32 makes sure that
*attrlen is align. The call tree is that:
nla_put_u16/nla_put_u32
-> nla_put attrlen = sizeof(u16) or sizeof(u32)
-> __nla_put attrlen
-> __nla_reserve attrlen
-> skb_put(skb, nla_total_size(attrlen))
nla_total_size returns the total length of attribute
including padding.
Cc: Joe Stringer <joe@ovn.org>
Cc: William Tu <u9012063@gmail.com>
Signed-off-by: Tonghao Zhang <xiangxia.m.yue@gmail.com>
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When using the kernel datapath, the upcall don't
include skb hash info relatived. That will introduce
some problem, because the hash of skb is important
in kernel stack. For example, VXLAN module uses
it to select UDP src port. The tx queue selection
may also use the hash in stack.
Hash is computed in different ways. Hash is random
for a TCP socket, and hash may be computed in hardware,
or software stack. Recalculation hash is not easy.
Hash of TCP socket is computed:
tcp_v4_connect
-> sk_set_txhash (is random)
__tcp_transmit_skb
-> skb_set_hash_from_sk
There will be one upcall, without information of skb
hash, to ovs-vswitchd, for the first packet of a TCP
session. The rest packets will be processed in Open vSwitch
modules, hash kept. If this tcp session is forward to
VXLAN module, then the UDP src port of first tcp packet
is different from rest packets.
TCP packets may come from the host or dockers, to Open vSwitch.
To fix it, we store the hash info to upcall, and restore hash
when packets sent back.
+---------------+ +-------------------------+
| Docker/VMs | | ovs-vswitchd |
+----+----------+ +-+--------------------+--+
| ^ |
| | |
| | upcall v restore packet hash (not recalculate)
| +-+--------------------+--+
| tap netdev | | vxlan module
+---------------> +--> Open vSwitch ko +-->
or internal type | |
+-------------------------+
Reported-at: https://mail.openvswitch.org/pipermail/ovs-dev/2019-October/364062.html
Signed-off-by: Tonghao Zhang <xiangxia.m.yue@gmail.com>
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The commit 69c51582ff786 ("dpif-netlink: don't allocate per
thread netlink sockets"), in Open vSwitch ovs-vswitchd, has
changed the number of allocated sockets to just one per port
by moving the socket array from a per handler structure to
a per datapath one. In the kernel datapath, a vport will have
only one socket in most case, if so select it directly in
fast-path.
Signed-off-by: Tonghao Zhang <xiangxia.m.yue@gmail.com>
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The openvswitch was supporting a MPLS label depth of 1 in the ingress
direction though the userspace OVS supports a max depth of 3 labels.
This change enables openvswitch module to support a max depth of
3 labels in the ingress.
Signed-off-by: Martin Varghese <martin.varghese@nokia.com>
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
use the specified functions to init resource.
Signed-off-by: Tonghao Zhang <xiangxia.m.yue@gmail.com>
Tested-by: Greg Rose <gvrose8192@gmail.com>
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Unlocking of a not locked mutex is not allowed.
Other kernel thread may be in critical section while
we unlock it because of setting user_feature fail.
Fixes: 95a7233c4 ("net: openvswitch: Set OvS recirc_id from tc chain index")
Cc: Paul Blakey <paulb@mellanox.com>
Signed-off-by: Tonghao Zhang <xiangxia.m.yue@gmail.com>
Tested-by: Greg Rose <gvrose8192@gmail.com>
Acked-by: William Tu <u9012063@gmail.com>
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we destroy the flow tables which may contain the flow_mask,
so release the flow mask struct.
Signed-off-by: Tonghao Zhang <xiangxia.m.yue@gmail.com>
Tested-by: Greg Rose <gvrose8192@gmail.com>
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The most case *index < ma->max, and flow-mask is not NULL.
We add un/likely for performance.
Signed-off-by: Tonghao Zhang <xiangxia.m.yue@gmail.com>
Tested-by: Greg Rose <gvrose8192@gmail.com>
Acked-by: William Tu <u9012063@gmail.com>
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simplify the code and remove the unnecessary BUILD_BUG_ON.
Signed-off-by: Tonghao Zhang <xiangxia.m.yue@gmail.com>
Tested-by: Greg Rose <gvrose8192@gmail.com>
Acked-by: William Tu <u9012063@gmail.com>
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The full looking up on flow table traverses all mask array.
If mask-array is too large, the number of invalid flow-mask
increase, performance will be drop.
One bad case, for example: M means flow-mask is valid and NULL
of flow-mask means deleted.
+-------------------------------------------+
| M | NULL | ... | NULL | M|
+-------------------------------------------+
In that case, without this patch, openvswitch will traverses all
mask array, because there will be one flow-mask in the tail. This
patch changes the way of flow-mask inserting and deleting, and the
mask array will be keep as below: there is not a NULL hole. In the
fast path, we can "break" "for" (not "continue") in flow_lookup
when we get a NULL flow-mask.
"break"
v
+-------------------------------------------+
| M | M | NULL |... | NULL | NULL|
+-------------------------------------------+
This patch don't optimize slow or control path, still using ma->max
to traverse. Slow path:
* tbl_mask_array_realloc
* ovs_flow_tbl_lookup_exact
* flow_mask_find
Signed-off-by: Tonghao Zhang <xiangxia.m.yue@gmail.com>
Tested-by: Greg Rose <gvrose8192@gmail.com>
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Port the codes to linux upstream and with little changes.
Pravin B Shelar, says:
| In case hash collision on mask cache, OVS does extra flow
| lookup. Following patch avoid it.
Link: 0e6efbe271
Signed-off-by: Tonghao Zhang <xiangxia.m.yue@gmail.com>
Tested-by: Greg Rose <gvrose8192@gmail.com>
Signed-off-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When creating and inserting flow-mask, if there is no available
flow-mask, we realloc the mask array. When removing flow-mask,
if necessary, we shrink mask array.
Signed-off-by: Tonghao Zhang <xiangxia.m.yue@gmail.com>
Tested-by: Greg Rose <gvrose8192@gmail.com>
Acked-by: William Tu <u9012063@gmail.com>
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Port the codes to linux upstream and with little changes.
Pravin B Shelar, says:
| mask caches index of mask in mask_list. On packet recv OVS
| need to traverse mask-list to get cached mask. Therefore array
| is better for retrieving cached mask. This also allows better
| cache replacement algorithm by directly checking mask's existence.
Link: d49fc3ff53
Signed-off-by: Tonghao Zhang <xiangxia.m.yue@gmail.com>
Tested-by: Greg Rose <gvrose8192@gmail.com>
Acked-by: William Tu <u9012063@gmail.com>
Signed-off-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The idea of this optimization comes from a patch which
is committed in 2014, openvswitch community. The author
is Pravin B Shelar. In order to get high performance, I
implement it again. Later patches will use it.
Pravin B Shelar, says:
| On every packet OVS needs to lookup flow-table with every
| mask until it finds a match. The packet flow-key is first
| masked with mask in the list and then the masked key is
| looked up in flow-table. Therefore number of masks can
| affect packet processing performance.
Link: 5604935e4e
Signed-off-by: Tonghao Zhang <xiangxia.m.yue@gmail.com>
Tested-by: Greg Rose <gvrose8192@gmail.com>
Acked-by: William Tu <u9012063@gmail.com>
Signed-off-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The only slightly tricky merge conflict was the netdevsim because the
mutex locking fix overlapped a lot of driver reload reorganization.
The rest were (relatively) trivial in nature.
Signed-off-by: David S. Miller <davem@davemloft.net>
In rtnl_net_notifyid(), we certainly can't pass a null GFP flag to
rtnl_notify(). A GFP_KERNEL flag would be fine in most circumstances,
but there are a few paths calling rtnl_net_notifyid() from atomic
context or from RCU critical sections. The later also precludes the use
of gfp_any() as it wouldn't detect the RCU case. Also, the nlmsg_new()
call is wrong too, as it uses GFP_KERNEL unconditionally.
Therefore, we need to pass the GFP flags as parameter and propagate it
through function calls until the proper flags can be determined.
In most cases, GFP_KERNEL is fine. The exceptions are:
* openvswitch: ovs_vport_cmd_get() and ovs_vport_cmd_dump()
indirectly call rtnl_net_notifyid() from RCU critical section,
* rtnetlink: rtmsg_ifinfo_build_skb() already receives GFP flags as
parameter.
Also, in ovs_vport_cmd_build_info(), let's change the GFP flags used
by nlmsg_new(). The function is allowed to sleep, so better make the
flags consistent with the ones used in the following
ovs_vport_cmd_fill_info() call.
Found by code inspection.
Fixes: 9a9634545c ("netns: notify netns id events")
Signed-off-by: Guillaume Nault <gnault@redhat.com>
Acked-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
the following script:
# tc qdisc add dev eth0 clsact
# tc filter add dev eth0 egress protocol ip matchall \
> action mpls push protocol mpls_uc label 0x355aa bos 1
causes corruption of all IP packets transmitted by eth0. On TC egress, we
can't rely on the value of skb->mac_len, because it's 0 and a MPLS 'push'
operation will result in an overwrite of the first 4 octets in the packet
L2 header (e.g. the Destination Address if eth0 is an Ethernet); the same
error pattern is present also in the MPLS 'pop' operation. Fix this error
in act_mpls data plane, computing 'mac_len' as the difference between the
network header and the mac header (when not at TC ingress), and use it in
MPLS 'push'/'pop' core functions.
v2: unbreak 'make htmldocs' because of missing documentation of 'mac_len'
in skb_mpls_pop(), reported by kbuild test robot
CC: Lorenzo Bianconi <lorenzo@kernel.org>
Fixes: 2a2ea50870 ("net: sched: add mpls manipulation actions to TC")
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Acked-by: John Hurley <john.hurley@netronome.com>
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch allows to attach conntrack helper to a confirmed conntrack
entry. Currently, we can only attach alg helper to a conntrack entry
when it is in the unconfirmed state. This patch enables an use case
that we can firstly commit a conntrack entry after it passed some
initial conditions. After that the processing pipeline will further
check a couple of packets to determine if the connection belongs to
a particular application, and attach alg helper to the connection
in a later stage.
Signed-off-by: Yi-Hung Wei <yihung.wei@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 174e23810c
("sk_buff: drop all skb extensions on free and skb scrubbing") made napi
recycle always drop skb extensions. The additional skb_ext_del() that is
performed via nf_reset on napi skb recycle is not needed anymore.
Most nf_reset() calls in the stack are there so queued skb won't block
'rmmod nf_conntrack' indefinitely.
This removes the skb_ext_del from nf_reset, and renames it to a more
fitting nf_reset_ct().
In a few selected places, add a call to skb_ext_reset to make sure that
no active extensions remain.
I am submitting this for "net", because we're still early in the release
cycle. The patch applies to net-next too, but I think the rename causes
needless divergence between those trees.
Suggested-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
userspace openvswitch patch "(dpif-linux: Implement the API
functions to allow multiple handler threads read upcall)"
changes its type from U32 to UNSPEC, but leave the kernel
unchanged
and after kernel 6e237d099f "(netlink: Relax attr validation
for fixed length types)", this bug is exposed by the below
warning
[ 57.215841] netlink: 'ovs-vswitchd': attribute type 5 has an invalid length.
Fixes: 5cd667b0a4 ("openvswitch: Allow each vport to have an array of 'port_id's")
Signed-off-by: Li RongQing <lirongqing@baidu.com>
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Offloaded OvS datapath rules are translated one to one to tc rules,
for example the following simplified OvS rule:
recirc_id(0),in_port(dev1),eth_type(0x0800),ct_state(-trk) actions:ct(),recirc(2)
Will be translated to the following tc rule:
$ tc filter add dev dev1 ingress \
prio 1 chain 0 proto ip \
flower tcp ct_state -trk \
action ct pipe \
action goto chain 2
Received packets will first travel though tc, and if they aren't stolen
by it, like in the above rule, they will continue to OvS datapath.
Since we already did some actions (action ct in this case) which might
modify the packets, and updated action stats, we would like to continue
the proccessing with the correct recirc_id in OvS (here recirc_id(2))
where we left off.
To support this, introduce a new skb extension for tc, which
will be used for translating tc chain to ovs recirc_id to
handle these miss cases. Last tc chain index will be set
by tc goto chain action and read by OvS datapath.
Signed-off-by: Paul Blakey <paulb@mellanox.com>
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Only the first fragment in a datagram contains the L4 headers. When the
Open vSwitch module parses a packet, it always sets the IP protocol
field in the key, but can only set the L4 fields on the first fragment.
The original behavior would not clear the L4 portion of the key, so
garbage values would be sent in the key for "later" fragments. This
patch clears the L4 fields in that circumstance to prevent sending those
garbage values as part of the upcall.
Signed-off-by: Justin Pettit <jpettit@ovn.org>
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When IP fragments are reassembled before being sent to conntrack, the
key from the last fragment is used. Unless there are reordering
issues, the last fragment received will not contain the L4 ports, so the
key for the reassembled datagram won't contain them. This patch updates
the key once we have a reassembled datagram.
The handle_fragments() function works on L3 headers so we pull the L3/L4
flow key update code from key_extract into a new function
'key_extract_l3l4'. Then we add a another new function
ovs_flow_key_update_l3l4() and export it so that it is accessible by
handle_fragments() for conntrack packet reassembly.
Co-authored-by: Justin Pettit <jpettit@ovn.org>
Signed-off-by: Greg Rose <gvrose8192@gmail.com>
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch addresses a conntrack cache issue with timeout policy.
Currently, we do not check if the timeout extension is set properly in the
cached conntrack entry. Thus, after packet recirculate from conntrack
action, the timeout policy is not applied properly. This patch fixes the
aforementioned issue.
Fixes: 06bd2bdf19 ("openvswitch: Add timeout support to ct action")
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Yi-Hung Wei <yihung.wei@gmail.com>
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes: 06bd2bdf19 ("openvswitch: Add timeout support to ct action")
Signed-off-by: Yi-Hung Wei <yihung.wei@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently in function ovs_dp_process_packet(), return values of
ovs_execute_actions() are silently discarded. This patch prints out
an debug message when error happens so as to provide helpful hints
for debugging.
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some functions in the datapath code are factored out so that each
one has a stack frame smaller than 1024 bytes with gcc. However,
when compiling with clang, the functions are inlined more aggressively
and combined again so we get
net/openvswitch/datapath.c:1124:12: error: stack frame size of 1528 bytes in function 'ovs_flow_cmd_set' [-Werror,-Wframe-larger-than=]
Marking both get_flow_actions() and ovs_nla_init_match_and_action()
as 'noinline_for_stack' gives us the same behavior that we see with
gcc, and no warning. Note that this does not mean we actually use
less stack, as the functions call each other, and we still get
three copies of the large 'struct sw_flow_key' type on the stack.
The comment tells us that this was previously considered safe,
presumably since the netlink parsing functions are called with
a known backchain that does not also use a lot of stack space.
Fixes: 9cc9a5cb17 ("datapath: Avoid using stack larger than 1024.")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a flow_stats structure defined in include/net/flow_offload.h
and a follow up patch adds #include <net/flow_offload.h> to
net/sch_generic.h.
This breaks compilation since OVS codebase includes net/sock.h which
pulls in linux/filter.h which includes net/sch_generic.h.
In file included from ./include/net/sch_generic.h:18:0,
from ./include/linux/filter.h:25,
from ./include/net/sock.h:59,
from ./include/linux/tcp.h:19,
from net/openvswitch/datapath.c:24
This definition takes precedence on OVS since it is placed in the
networking core, so rename flow_stats in OVS to sw_flow_stats since
this structure is contained in sw_flow.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a vport is deleted, the maximum headroom size would be changed.
If the vport which has the largest headroom is deleted,
the new max_headroom would be set.
But, if the new headroom size is equal to the old headroom size,
updating routine is unnecessary.
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Tested-by: Greg Rose <gvrose8192@gmail.com>
Reviewed-by: Greg Rose <gvrose8192@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Open vSwitch allows the updating of an existing MPLS header on a packet.
In preparation for supporting similar functionality in TC, move this to a
common skb helper function.
Signed-off-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Acked-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Open vSwitch provides code to pop an MPLS header to a packet. In
preparation for supporting this in TC, move the pop code to an skb helper
that can be reused.
Remove the, now unused, update_ethertype static function from OvS.
Signed-off-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Acked-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Open vSwitch provides code to push an MPLS header to a packet. In
preparation for supporting this in TC, move the push code to an skb helper
that can be reused.
Signed-off-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Acked-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use netif_ovs_is_port() function instead of open code.
This patch doesn't change logic.
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Skbs may have their checksum value populated by HW. If this is a checksum
calculated over the entire packet then the CHECKSUM_COMPLETE field is
marked. Changes to the data pointer on the skb throughout the network
stack still try to maintain this complete csum value if it is required
through functions such as skb_postpush_rcsum.
The MPLS actions in Open vSwitch modify a CHECKSUM_COMPLETE value when
changes are made to packet data without a push or a pull. This occurs when
the ethertype of the MAC header is changed or when MPLS lse fields are
modified.
The modification is carried out using the csum_partial function to get the
csum of a buffer and add it into the larger checksum. The buffer is an
inversion of the data to be removed followed by the new data. Because the
csum is calculated over 16 bits and these values align with 16 bits, the
effect is the removal of the old value from the CHECKSUM_COMPLETE and
addition of the new value.
However, the csum fed into the function and the outcome of the
calculation are also inverted. This would only make sense if it was the
new value rather than the old that was inverted in the input buffer.
Fix the issue by removing the bit inverts in the csum_partial calculation.
The bug was verified and the fix tested by comparing the folded value of
the updated CHECKSUM_COMPLETE value with the folded value of a full
software checksum calculation (reset skb->csum to 0 and run
skb_checksum_complete(skb)). Prior to the fix the outcomes differed but
after they produce the same result.
Fixes: 25cd9ba0ab ("openvswitch: Add basic MPLS support to kernel")
Fixes: bc7cc5999f ("openvswitch: update checksum in {push,pop}_mpls")
Signed-off-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
