The defines are taken from dt-bindings/pinctrl/am33xx.h
Signed-off-by: Christina Quast <cquast@hanoverdisplays.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Switch to use phy-gmii-sel PHY instead of cpsw-phy-sel.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add stdout-path property in /chosen node so that earlycon can be
used by just adding earlycon in bootargs.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The phy_id property is deprecated and phy-handle has to be used instead.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The interrupt for power button is static data that comes from the
datasheet, there is no reason to need to define this value on every
board so seams reasonable put this information into the common tps65217
file.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The interrupt specifiers for USB and AC charger input are static data that
comes from the datasheet, there is no reason to need to define these values
on every board so seem reasonable put this information into the common
tps65217 file.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
chiliBoard has a battery connector, so support charging battery
through tps65217 chip.
Additionally, enabling tps65217 charger allows us to get status
of AC power.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
On chiliBoard power button is connected to TPS65217. It signals power
button presses by asserting interrupt output and allows to read the
state by i2c bus.
Handle TPS65217 interrupts and enable notifications of power button
presses.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
ChiliSOM has 2 Ethernet subsystems with different types of possibly used
PHY interfaces (i.e. MII, RMII, GMII, RGMII). Current code configured
pinmux for RMII on 1st Ethernet subsystem and enabled Ethernet MAC with
1 slave for all boards which use ChiliSOM.
This change moves pinmux configuration of 1st Ethernet subsystem to
ChiliBoard description, as this is board-specific.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
uart0 configuration code has been in SOM. However, it is possible to
use all (or none) of 6 uart's of AM335x processor present on ChiliSOM.
This fix moves declaration of uart0 from ChiliSOM to ChiliBoard, because
use of uart is strictly board-specific.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Use the pinmux IOPAD macro to define the register absolute physical
address instead of the offset from the padconf base address. This
makes the DTS easier to read since matches the addresses listed in
the Technical Reference Manual.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
