We rely on the return code of wacom_bpt*() to do the input_sync().
wacom_wac_irq() then properly sync the input devices.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Reviewed-by: Ping Cheng <pingc@wacom.com>
Reviewed-by: Jason Gerecke <killertofu@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
MSC_SERIAL can be safely dropped for pad input devices.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Reviewed-by: Ping Cheng <pingc@wacom.com>
Reviewed-by: Jason Gerecke <killertofu@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Currently, the pad events are sent through the stylus input device
for the Intuos/Cintiqs, and through the touch input device for the
Bamboos.
To differentiate the buttons pressed on the pad from the ones pressed
on the stylus, the Intuos/Cintiq uses MISC_SERIAL and ABS_MISC. This
lead to a multiplexing of the events into one device, which are then
splitted out in xf86-input-wacom. Bamboos are not using MISC events
because the pad is attached to the touch interface, and only BTN_TOUCH
is used for the finger (and DOUBLE_TAP, etc...). However, the user space
driver still splits out the pad from the touch interface in the same
way it does for the pro line devices.
The other problem we can see with this fact is that some of the Intuos
and Cintiq have a wheel, and the effective range of the reported values
is [0..71]. Unfortunately, the airbrush stylus also sends wheel events
(there is a small wheel on it), but in the range [0..1023]. From the user
space point of view it is kind of difficult to understand that because
the wheel on the pad are quite common, while the airbrush tool is not.
A solution to fix all of these problems is to split out the pad device
from the stylus/touch. This decision makes more sense because the pad is
not linked to the absolute position of the finger or pen, and usually, the
events from the pad are filtered out by the compositor, which then convert
them into actions or keyboard shortcuts.
For backward compatibility with current xf86-input-wacom, the pad devices
still present the ABS_X, ABS_Y and ABS_MISC events, but they can be
completely ignored in the new implementation.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Reviewed-by: Ping Cheng <pingc@wacom.com>
Reviewed-by: Jason Gerecke <killertofu@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This field was not used for 9 years, it is time to assign it.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This reverts commit 1b2faaf7e2.
The Intuos4 series presents a bug in which it hangs if it receives
a set feature command while switching to the enhanced mode.
This bug is triggered when plugging an Intuos 4 while having
a gnome user session up and running.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Aristeu Rozanski <aris@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
wacom_wac.h will be moving to drivers/hid. Since we only need 3 definitions
from it let's simply copy them over.
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Recent version of xf86-input-wacom no longer support directly accessing
serial tablets. Instead xf86-input-wacom now expects all wacom tablets to
be driven by the kernel and to show up as evdev devices.
This has caused old serial Wacom tablets to stop working for people who still
have such tablets. Julian Squires has written a serio input driver to fix this:
https://github.com/tokenrove/wacom-serial-iv
This is a cleaned up version of this driver with improved Graphire support
(I own an old Graphire myself).
Signed-off-by: Julian Squires <julian@cipht.net>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
New Cintiq tablets have a 200 tablet counts outside of screen area.
Add x/y_min for ABS_X/Y to pass this information to userland.
Signed-off-by: Ping Cheng <pingc@wacom.com>
Reviewed-by: Jason Gerecke <killertofu@gmail.com>
Tested-by: Jason Gerecke <killertofu@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This patch adds support for the 0x4004, 0x5000, and 0x5002 sensors found
on what should be the Motion R12, Fujitsu Q704, and Fujitsu T904. These
tablets use a new report ID (3) for their touch packets and a slightly
different HID descriptor format, but are otherwise largely identical in
protocol to the "MTTPC" tablets.
Note:
* The R12 uses its 0x4004 sensor for touch input only. A pen interface
is not present in its HID descriptor, though its possible a 0x4004
may be used for pen input by other tablet PCs in the future.
* The 0x5002 sensor appears to use a new report ID (8) for its pen
packets. The other sensors continue to use the traditional report
ID (2).
Signed-off-by: Jason Gerecke <killertofu@gmail.com>
Reviewed-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
A few cases of incorrectly using 'le16_to_cpup' instead of
'get_unaligned_le16' have been noticed and fixed.
Signed-off-by: Jason Gerecke <killertofu@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJTbTZoAAoJEHm+PkMAQRiGLssH/3Rv6e9rAkEw9Ey0ymwGsCvf
6DEAcSgaWEyYWEU+DmkEQ3hbiOyESHFOsWE4zA2F5WY0w2Xsr+wDCS+14WCN6NHT
6sxSYGj1hd+ni6GhlGxfRpUXtY59h7TKHaaHYKPIOsO4OWXVeD53trpq416kvqal
zWkFOWeiEyeJnNKv0z0+5QWTeFDjTd1YawWcK/8kFez1Y4BXBECTgKoJaEcvowfU
j7oQ0BJxtLlxFgCB84bZTUbGuyn1x9FiS7Z2w9JcqSkTLMabFjsbA15eZIV66N4s
boaxlRvyvelR09eiiYYqOLxUmeEi1wRqtAM3yln1Y5/MX+DAmf5/sylqKtC5eLg=
=ezkr
-----END PGP SIGNATURE-----
Merge tag 'v3.15-rc5' into next
Merge with Linux 3.15-rc5 to sync up Wacom and other changes.
The Win8 version of the Panasonic CF-H2 includes a new Wacom device.
The pen interface appears to use the same protocol as before, but the
touch interface has been tweaked to send Win8-compatible reports.
Signed-off-by: Jason Gerecke <killertofu@gmail.com>
Reviewed-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Some tablet PC sensors (e.g. the 0xEC found in the Thinkpad Yoga) report
more than 256 pressure levels and will experience wraparound unless the
full range is read.
Signed-off-by: Jason Gerecke <killertofu@gmail.com>
Tested-by: Aaron Skomra <Aaron.Skomra@wacom.com>
Reviewed-by: Carl Worth <cworth@cworth.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
'wacom->data' contains raw binary data and can lead to unexpected behavior
if a byte under examination happens to have its MSB set.
Signed-off-by: Jason Gerecke <killertofu@gmail.com>
Tested-by: Aaron Skomra <Aaron.Skomra@wacom.com>
Reviewed-by: Carl Worth <cworth@cworth.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The 0xEC sensor is used in multiple tablet PCs and curiously has versions
that report 256 levels of pressure (Samsung Slate 7) as well as versions
that report 1024 levels (Lenovo Thinkpad Yoga). To allow both versions to
work properly, we allow the value of HID_USAGE_PRESSURE reported to
override pressure_max.
Signed-off-by: Jason Gerecke <killertofu@gmail.com>
Tested-by: Aaron Skomra <Aaron.Skomra@wacom.com>
Reviewed-by: Carl Worth <cworth@cworth.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
A HID Usage is a 32-bit value: an upper 16-bit "page" and a lower 16-bit
ID. While the two halves are normally reported seperately, only the
combination uniquely idenfifes a particular HID Usage.
The existing code performs the comparison in two steps, first performing a
switch on the ID and then verifying the page within each case. While this
works fine, it is very akward to handle two Usages that share a single ID,
such as HID_USAGE_PRESSURE and HID_USAGE_X because the case statement can
only have a single identifier.
To work around this, we now check the full 32-bit HID Usage directly rather
than first checking the ID and then the page. This allows the switch
statement to have distinct cases for e.g. HID_USAGE_PRESSURE and
HID_USAGE_X.
Signed-off-by: Jason Gerecke <killertofu@gmail.com>
Tested-by: Aaron Skomra <Aaron.Skomra@wacom.com>
Reviewed-by: Carl Worth <cworth@cworth.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
There is usb_get_dev() in gtco_probe(), but there is no usb_put_dev()
anywhere in the driver.
As pointed out by Dmitry Torokhov:
The lifetime of gtco structure is already directly tied to lifetime of
usb_dev: when destroying usb_dev driver core will call remove() function
of currently bound driver (in our case gtco) which will destroy gtco
memory. Taking additional reference is not needed here.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
features->quirks can have multiple bits set. For dual input, we only
need to check WACOM_QUIRK_MULTI_INPUT.
Reviewed-by: Jason Gerecke <killertofu@gmail.com>
Signed-off-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
None of these files are actually using any __init type directives
and hence don't need to include <linux/init.h>. Most are just a
left over from __devinit and __cpuinit removal, or simply due to
code getting copied from one driver to the next.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
New Intuos series models added a hardware switch to turn touch
data on/off. The state of the switch is reported periodically
from the tablet. To report the state the driver will emit SW_MUTE_DEVICE
events.
Reviewed_by: Chris Bagwell <chris@cnpbagwell.com>
Acked-by: Peter Hutterer <peter.hutterer@who-t.net>
Tested-by: Jason Gerecke <killertofu@gmail.com>
Signed-off-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.15 (GNU/Linux)
iQEcBAABAgAGBQJSrhGrAAoJEHm+PkMAQRiGsNoH/jIK3CsQ2lbW7yRLXmfgtbzz
i2Kep6D4SDvmaLpLYOVC8xNYTiE8jtTbSXHomwP5wMZ63MQDhBfnEWsEWqeZ9+D9
3Q46p0QWuoBgYu2VGkoxTfygkT6hhSpwWIi3SeImbY4fg57OHiUil/+YGhORM4Qc
K4549OCTY3sIrgmWL77gzqjRUo+pQ4C73NKqZ3+5nlOmYBZC1yugk8mFwEpQkwhK
4NRNU760Fo+XIht/bINqRiPMddzC15p0mxvJy3cDW8bZa1tFSS9SB7AQUULBbcHL
+2dFlFOEb5SV1sNiNPrJ0W+h2qUh2e7kPB0F8epaBppgbwVdyQoC2u4uuLV2ZN0=
=lI2r
-----END PGP SIGNATURE-----
Merge tag 'v3.13-rc4' into next
Synchronize with mainline to bring in the new keycode definitions and
new hwmon API.
Two tablets in this series support both pen and touch. One (Intuos S)
only supports pen. This patch also updates the driver to process wireless
devices that do not support touch interface.
Tested-by: Jason Gerecke <killertofu@gmail.com>
Reviewed-by: Chris Bagwell <chris@cnpbagwell.com>
Signed-off-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Old single touch Tablet PCs do not have touch_max set at
wacom_features. Since touch device at lease supports one
finger, assign touch_max to 1 when touch usage is defined
in its HID Descriptor and touch_max is not pre-defined.
Tested-by: Jason Gerecke <killertofu@gmail.com>
Signed-off-by: Ping Cheng <pingc@wacom.com>
Reviewed-by: Chris Bagwell <chris@cnpbagwell.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The width and height values reported by the Intuos Pro are not in
surface units as required by the MT protocol. A simple multiplier
of 100x corrects it.
Signed-off-by: Jason Gerecke <killertofu@gmail.com>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Some multi-interface devices support expresskeys on a separate interface,
such as Bamboo; some multi-interface devices do not support touch at all,
such as Pen only Intuos5. Make sure we report the right device names.
Tested-by: Jason Gerecke <killertofu@gmail.com>
Signed-off-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This will stop UPower from detecting the tablet as a power supply,
and using its battery status to hibernate or switch off the machine.
https://bugs.freedesktop.org/show_bug.cgi?id=70321
Signed-off-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The EMR sensor of Intuos4 and newer devices can send a packet with
0x20 in its second byte which contains only location information.
This packet is sent when the pen is too far away to reliably obtain
other information. Because only the location is updated userspace
will continue to see stale information for other values, most notably
TOUCH, PRESSURE, and DISTANCE.
This patch ensures userspace is not left with stale device state
information when the pen re-enters proximity (possibly leading to
the assumption the pen is still in contact even though it is
actually hovering).
Signed-off-by: Jason Gerecke <killertofu@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Adds support for the sensors integrated in to the Cintiq Companion
Hybrid. These sensors use by-and-large the same protocol as the
Cintiq 24HD touch.
NOTE: The ExpressKeys on the Cintiq Companion Hybrid are wired to
both the EMR controller and CPU GPIO pins. It may be necessary to
disable their functionality in this driver if building a custom
Android kernel for this device (lest two events be sent to userspace
for every button press).
Signed-off-by: Jason Gerecke <killertofu@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iQEcBAABAgAGBQJSJPkeAAoJEHm+PkMAQRiGVWMH/jo5f01Ra7G4/CYS59K+AlBQ
/oWL3W81r5MORlsMxwUwGtJ3sZ7UulKwiDrluWeOkz2+/9SmoHoUfkpbByq1bSIV
y0eqhmjtkHQZz5radJIHeyz1gJIICBIgAM0l45j8SpK4n9EXRcjLSZjdjAkPzxZp
qZpfxKhVSTu79m96bud7F+HrboHDQEyhD9zqdSi4xPQNnOmTc7K3tvui9AB3rMbV
ablM3C+LqBYjZx+pKS/rOdfATxZvtU392HU53XTALt6VD1e8alMmhmpe0I9Zxvjv
scsB6hfRkevfe7VaK3aVoDnQnLKd61yxs+/XdzTtkWPbVGp+kiuFUdDv/5y2r1g=
=7Xf6
-----END PGP SIGNATURE-----
Merge tag 'v3.11' into next
Merge with mainline to bring in sync changes to cyttsp4 driver.
Fix to return a negative error code from the urb submit error
handling case instead of 0, as done elsewhere in this function.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
plus send begin and end of express keys events for
Cintiq 13HD and DTH2242/DTK2241
Signed-off-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Add new styli for Cintiq 13HD and 22HD. Update comments for
for tools. Check whole 10 nibbles of tool ID for tool
types. Remove unuecessary tool type for Intuos series PAD.
Signed-off-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Same as Cintiq 24HDT, DTH2242 has two interfaces sharing one configuration.
This patch ignores the second interface.
Signed-off-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The MFT device in the Cintiq 24HDT has two interfaces sharing the
same configuration. Without this patch, the driver attempts to
make use of both interfaces, even though the second interface is
not compatible with this driver.
Signed-off-by: Jason Gerecke <killertofu@gmail.com>
Tested-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
It is a Wacom device found in Fujitsu Lifebook T902.
Signed-off-by: Stephan Frank <sfrank@cs.tu-berlin.de>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Logic sets a value and then reads it back to make sure it worked
and retries write on failures. Since read and write share a buffer,
it needs to be set back up before writing though.
Issue is not seen a lot because 1) it doesn't need to retry for
a lot of tablets and 2) a lot of failures that need a retry are
from an -ETIMEDOUT and hopefully buffer is not touched in this case.
At least one user has shown logs with buffer being modified during
-ETIMEDOUT case with linux 3.7 kernel.
Signed-off-by: Chris Bagwell <chris@cnpbagwell.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This patch brings wacom driver in-sync with input-mt changes
made in release 3.7.
Signed-off-by: Ping Cheng <pingc@wacom.com>
Reviewed-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Henrik added new MT routines in release 3.7. This patch is to prepare
for the use of new MT routines.
In the newly added wacom_abs_set_axis() function, the first
if-statement assigns ABS_X/Y for number of contacts less or equal
to 2. So, it is single and 2 finger touch devices. Two finger touch
devices are processed here since they will not use the updated
input_mt_init_slots(), which does not offer benefit to those devices.
input_mt_init_slots() will take care of ABS_X/Y assignment when flags
are not zero. All touch devices with more than two contacts will use
input_mt_init_slots() with non-zero flags.
The second if-statement is for all MT devices, which include two
finger touch devices.
Signed-off-by: Ping Cheng <pingc@wacom.com>
Reviewed-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Commit f393ee2b81 forgot to add the
touch_max property for Wacom Bamboo Fun CTH-461/S, ID 056a:00d2.
This broke the touch functionality for that device. This patch,
(done with help of Ping Cheng), adds the correct value and makes
touch work again.
Signed-off-by: Diego Calleja <diegocg@gmail.com>
Reviewed-by: Ping Cheng <pinglinux@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The updated type enum enables this implementation.
Signed-off-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This adds support for the two new multi-touch tablets.
Signed-off-by: Ping Cheng <pinglinux@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Use switch instead of if statement to verify device types
Signed-off-by: Ping Cheng <pinglinux@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iQEcBAABAgAGBQJQjYaSAAoJEHm+PkMAQRiGIlYH+wbwj7i5CcUG46VRFT5WlG7W
iYaojL68FKKIUCBh4GOvZxE2D907KgqHQI6rePE/xDhK493d0Nyi4PGQJ1JoTE+l
JQq++C3CoX9mm/zCRW5JyOcemE4t2t1/poi2ege9Kf9E9N5Cw0P4r8Cz1urCFKL6
EO2/gA5d6cBQpg+gVq9T88SnYgiJGs7d8AYjFeC7SrqIwDvG6tfg+YF4IRxC4QAc
0zbBgej/kbuiLbGl2ltU0I9HTOwlTgp53tdYe810cs3CdzNC2ykdF391Q24tloeo
uxmCSQrA2upHA9aILqY+T5f+cMOpVS4T8Ica3N9OzVEIPXSh2K9d4tESGPikMEE=
=yiDr
-----END PGP SIGNATURE-----
Merge tag 'v3.7-rc3' into for-linus to sync up with recent USB changes
Decode multitouch reports from the touch sensor of the Cintiq 24HD
touch.
Signed-off-by: Jason Gerecke <killertofu@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Like our other pen-and-touch products, the Cintiq 24HD touch needs data
to be shared between its two sensors to facilitate proximity-based palm
rejection.
Unlike other tablets that report sensor data through separate interfaces
of the same USB device, the Cintiq 24HD touch has separate USB devices
that are connected to an internal USB hub.
This patch makes it possible to designate the USB VID/PID of the other
device so that the two may share data. To ensure we don't accidentally
link to a sensor from a physically separate device (if several have been
plugged in), we limit the search to siblings (i.e., devices directly
connected to the same hub).
Signed-off-by: Jason Gerecke <killertofu@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Rewrites this function to be easier to read and understand. The new
function 'wacom_set_device_mode' now handles the grunt work of
assembling the proper feature report, sending it to the device,
and ensuring the setting "sticks".
Signed-off-by: Jason Gerecke <killertofu@gmail.com>
Tested-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The Cintiq 24HD touch cannot use wacom_set_phy_from_res to determine
the physical size of the touch sensor since the pen and touch are
on separate USB devices. The physical size is, however, provided in
the HID descriptor, just scaled to a unit we don't use.
This patch introduces the function wacom_fix_phy_from_hid to let
us make use of the unit and exponent data provided by HID to set
the [xy]_phy variables to an appropriate value. This function
relies on a trimmed-down version of hidinput_calc_abs_res from
the hid-input.c.
Signed-off-by: Jason Gerecke <killertofu@gmail.com>
Tested-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The ability to set the proximity flag should apply to any device
that has both pen and touch input. Rather than listing classes of
devices known to meet this criteria, simply filter on the quirk
defining all such devices.
Signed-off-by: Jason Gerecke <killertofu@gmail.com>
Tested-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This changes how the touch packets for Intuos5 and 3rd-gen Bamboo
are interpreted, so that proper values for the MAJOR and MINOR
axes are reported. Instead of using the amplitude field (data[6]),
we use the size field (data[5]) and do some calculation to
transform it from a scaled-down area into axis lengths.
Note that even though we assume a circular contact, both MAJOR and
MINOR are reported since the resolution of the X and Y axes differ.
Signed-off-by: Jason Gerecke <killertofu@gmail.com>
Reviewed-by: Chris Bagwell <chris@cnpbagwell.com>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Merge Henrik's updates to multitouch code. Even though Jiri already
pulled them in I need to do it too since my changes to evdev using
dynamic major would clash with them.
If the ExpressKeys on the Intuos5 are touched, they currently result
an out-of-prox packet being sent even if the pad is already out of
prox. This can cause some confusion in the X driver. To restore the
expected semantics, we make being touched a sufficient condition to
signal proximity.
https://bugs.freedesktop.org/show_bug.cgi?id=54250
Reported-by: Timo Aaltonen <tjaalton@ubuntu.com>
Signed-off-by: Jason Gerecke <killertofu@gmail.com>
Reviewed-by: Chris Bagwell <chris@cnpbagwell.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Preparing to move more repeated code into the mt core, add a flags
argument to the input_mt_slots_init() function.
Reviewed-and-tested-by: Benjamin Tissoires <benjamin.tissoires@enac.fr>
Tested-by: Ping Cheng <pingc@wacom.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Adds support for the EMR digitizer on the Cintiq 24HD touch. The
EMR digitizer should work identically to that found on the Cintiq
24HD. The touch digitizer is a separate USB device similar to how
we split apart some other devices.
Signed-off-by: Jason Gerecke <killertofu@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Adds support for the EMR digitizer on the Cintiq 24HD touch. The
EMR digitizer should work identically to that found on the Cintiq
24HD. The touch digitizer is a separate USB device similar to how
we split apart some other devices.
Signed-off-by: Jason Gerecke <killertofu@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This change adds support for old Hanwang Art master II tablet
Signed-off-by: weixing <weixing@hanwang.com.cn>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Some models, such as 0xE6, report more fingers than we process.
Reported-by: Jonathan Nieder <jrnieder@gmail.com>
Signed-off-by: Ping Cheng <pingc@wacom.com>
Tested-by: Nils Kanning <nils@kanning.de>
Tested-by: Rafi Rubin <rafi@seas.upenn.edu>
Reviewed-by: Jason Gerecke <killertofu@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
rep_data is not an array anymore, so taking it's address when passing to
wacom_get_report() is wrong.
Signed-off-by: Ping Cheng <pingc@wacom.com>
Tested-by: Rafi Rubin <rafi@seas.upenn.edu>
Reviewed-by: Jason Gerecke <killertofu@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Replaces code to calculate Intuos5 physical dimensions with a call
to an existing function that performs the same task.
Signed-off-by: Jason Gerecke <killertofu@gmail.com>
Reviewed-by: Chris Bagwell <chris@cnpbagwell.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This case appears to have been missed in the original commit.
Signed-off-by: Jason Gerecke <killertofu@gmail.com>
Reviewed-by: Chris Bagwell <chris@cnpbagwell.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Bamboo One's with ID of 0x6a and 0x6b were added with correct
indication of 1024 pressure levels but the Graphire packet routine
was only looking at 9 bits. Increased to 10 bits.
This bug caused these devices to roll over to zero pressure at half
way mark.
The other devices using this routine only support 256 or 512 range
and look to fix unused bits at zero.
Signed-off-by: Chris Bagwell <chris@cnpbagwell.com>
Reported-by: Tushant Mirchandani <tushantin@gmail.com>
Reviewed-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Do not register battery device until connected to a tablet.
This prevents an empty battery icon from being shown when tablet is
connected using USB cable.
Also, call power_supply_powers() for apps that can make use of that
info.
And stop ignoring input registration failures.
Signed-off-by: Chris Bagwell <chris@cnpbagwell.com>
Reviewed-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
So we can simplify a few type related if statements
Signed-off-by: Ping Cheng <pingc@wacom.com>
Acked-by: Chris Bagwell <chris@cnpbagwell.com>
Reviewed-by: Jason Gerecke <killertofu@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Pull input layer updates from Dmitry Torokhov:
- a bunch of new drivers (DA9052/53 touchscreenn controller, Synaptics
Navpoint, LM8333 keypads, Wacom I2C touhscreen);
- updates to existing touchpad drivers (ALPS, Sntelic);
- Wacom driver now supports Intuos5;
- device-tree bindings in numerous drivers;
- other cleanups and fixes.
Fix annoying conflict in drivers/input/tablet/wacom_wac.c that I think
implies that the input layer device naming is broken, but let's see. I
brough it up with Dmitry.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (57 commits)
Input: matrix-keymap - fix building keymaps
Input: spear-keyboard - document DT bindings
Input: spear-keyboard - add device tree bindings
Input: matrix-keymap - wire up device tree support
Input: matrix-keymap - uninline and prepare for device tree support
Input: adp5588 - add support for gpio names
Input: omap-keypad - dynamically handle register offsets
Input: synaptics - fix compile warning
MAINTAINERS: adjust input-related patterns
Input: ALPS - switch to using input_mt_report_finger_count
Input: ALPS - add semi-MT support for v4 protocol
Input: Add Synaptics NavPoint (PXA27x SSP/SPI) driver
Input: atmel_mxt_ts - dump each message on just 1 line
Input: atmel_mxt_ts - do not read extra (checksum) byte
Input: atmel_mxt_ts - verify object size in mxt_write_object
Input: atmel_mxt_ts - only allow root to update firmware
Input: atmel_mxt_ts - use CONFIG_PM_SLEEP
Input: sentelic - report device's production serial number
Input: tl6040-vibra - Device Tree support
Input: evdev - properly handle read/write with count 0
...
Previously I had made the struct device point to the input device, but
after talking with Dmitry, he said that the USB device would make more
sense for this driver to point to. So converted it to use that instead.
CC: Dmitry Torokhov <dmitry.torokhov@gmail.com>
CC: Ping Cheng <pingc@wacom.com>
CC: Chris Bagwell <chris@cnpbagwell.com>
CC: Eduard Hasenleithner <eduard@hasenleithner.at>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Previously I had made the struct device point to the input device, but
after talking with Dmitry, he said that the USB device would make more
sense for this driver to point to. So converted it to use that instead.
CC: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Previously I had made the struct device point to the input device, but
after talking with Dmitry, he said that the USB device would make more
sense for this driver to point to. So converted it to use that instead.
CC: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Previously I had made the struct device point to the input device, but
after talking with Dmitry, he said that the USB device would make more
sense for this driver to point to. So converted it to use that instead.
CC: Dmitry Torokhov <dmitry.torokhov@gmail.com>
CC: Jesper Juhl <jj@chaosbits.net>
CC: JJ Ding <dgdunix@gmail.com>
CC: Edwin van Vliet <edwin@cheatah.nl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Previously I had made the struct device point to the input device, but
after talking with Dmitry, he said that the USB device would make more
sense for this driver to point to. So converted it to use that instead.
CC: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Instead of returning 1 (which is not even negative) let's capture and return
error codde returned by usb_get_extra_descriptor().
Reviewed-by: Chris Bagwell <chris@cnpbagwell.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
