Disabling ethernet during reboot (only to enable it again when the
ethernet driver attaches) can put the chip into a faulty state where it
corrupts the header of all incoming packets.
This happens if packets arrive during the time window where the core is
disabled, and it can be easily reproduced by rebooting while sending a
flood ping to the broadcast address.
Fixes: 95135bfa7e ("MIPS: Lantiq: Deactivate most of the devices by default")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Acked-by: John Crispin <john@phrozen.org>
Cc: hauke.mehrtens@lantiq.com
Cc: linux-mips@linux-mips.org
Cc: <stable@vger.kernel.org> # 4.4.x-
Patchwork: https://patchwork.linux-mips.org/patch/15078/
Signed-off-by: James Hogan <james.hogan@imgtec.com>
physical_memsize is needed by the vpe loader code and the platform
specific code has to define it. This value will be given to the
firmware loaded with the VPE loader. I am not aware of any standard
interface or better value to provide here.
Reported-by: kbuild test robot <lkp@intel.com>
Fixes: d9ae4f18c0 ("MIPS: Lantiq: Activate more drivers in default configuration")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: John Crispin <john@phrozen.org>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/14908/
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Historically a lot of these existed because we did not have
a distinction between what was modular code and what was providing
support to modules via EXPORT_SYMBOL and friends. That changed
when we forked out support for the latter into the export.h file.
This means we should be able to reduce the usage of module.h
in code that is obj-y Makefile or bool Kconfig. In the case of
some code where it is modular, we can extend that to also include
files that are building basic support functionality but not related
to loading or registering the final module; such files also have
no need whatsoever for module.h
The advantage in removing such instances is that module.h itself
sources about 15 other headers; adding significantly to what we feed
cpp, and it can obscure what headers we are effectively using.
Since module.h might have been the implicit source for init.h
(for __init) and for export.h (for EXPORT_SYMBOL) we consider each
instance for the presence of either and replace/add as needed.
Also note that MODULE_DEVICE_TABLE is a no-op for non-modular code.
Build coverage of all the mips defconfigs revealed the module.h
header was masking a couple of implicit include instances, so
we add the appropriate headers there.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: David Daney <david.daney@cavium.com>
Cc: John Crispin <john@phrozen.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: "Steven J. Hill" <steven.hill@cavium.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/15131/
[james.hogan@imgtec.com: Preserve sort order where it already exists]
Signed-off-by: James Hogan <james.hogan@imgtec.com>
With the IRQ stack changes integrated, the XRX200 devices started
emitting a constant stream of kernel messages like this:
[ 565.415310] Spurious IRQ: CAUSE=0x1100c300
This is caused by IP0 getting handled by plat_irq_dispatch() rather than
its vectored interrupt handler, which is fixed by commit de856416e714
("MIPS: IRQ Stack: Fix erroneous jal to plat_irq_dispatch").
Fix plat_irq_dispatch() to handle non-vectored IPI interrupts correctly
by setting up IP2-6 as proper chained IRQ handlers and calling do_IRQ
for all MIPS CPU interrupts.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Acked-by: John Crispin <john@phrozen.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/15077/
[james.hogan@imgtec.com: tweaked commit message]
Signed-off-by: James Hogan <james.hogan@imgtec.com>
The DMA controller channel and port configuration is changed by
selecting the port or channel in one register and then update the
configuration in other registers. This has to be done in an atomic
operation. Previously only the local interrupts were deactivated which
works for single CPU systems. If the system supports SMP a better
locking is needed, use spinlocks instead.
On more recent SoCs (at least xrx200 and later) there are two memory
regions to change the configuration, there we could use one area for
each CPU and do not have to synchronize between the CPUs and more.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Cc: john@phrozen.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/14912/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Hauke already fixed a couple of them, but one instance remains
that checks for a negative integer when it should check
for a NULL pointer:
arch/mips/lantiq/xway/sysctrl.c: In function 'ltq_soc_init':
arch/mips/lantiq/xway/sysctrl.c:473:19: error: ordered comparison of pointer with integer zero [-Werror=extra]
Fixes: 6e80785267 ("MIPS: Lantiq: Fix check for return value of request_mem_region()")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: John Crispin <john@phrozen.org>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/15043/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The hardware documentation says bit 11:10 are used for the GPE
frequency selection. Fix the mask in the define to match these bits.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Thomas Langer <thomas.langer@intel.com>
Cc: linux-mips@linux-mips.org
Cc: john@phrozen.org
Patchwork: https://patchwork.linux-mips.org/patch/14648/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The Kconfig currently controlling compilation of this code is:
arch/mips/lantiq/Kconfig:config XRX200_PHY_FW
arch/mips/lantiq/Kconfig: bool "XRX200 PHY firmware loader"
...meaning that it currently is not being built as a module by anyone.
Lets remove the couple traces of modular infrastructure use, so that
when reading the driver there is no doubt it is builtin-only.
Since module_platform_driver() uses the same init level priority as
builtin_platform_driver() the init ordering remains unchanged with
this commit.
Also note that MODULE_DEVICE_TABLE is a no-op for non-modular code.
We also delete the MODULE_LICENSE tag etc. since all that information
was (or is now) contained at the top of the file in the comments.
We don't replace module.h with init.h since the file doesn't need that.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: John Crispin <john@phrozen.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/13932/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The Makefile entry controlling compilation of this code is:
arch/mips/lantiq/xway/vmmc.o
---> arch/mips/lantiq/xway/Makefile:obj-y += vmmc.o
...meaning that it currently is not being built as a module by anyone.
Since module_platform_driver() uses the same init level priority as
builtin_platform_driver() the init ordering remains unchanged with
this commit.
Also note that MODULE_DEVICE_TABLE is a no-op for non-modular code.
We replace module.h with export.h since the file does actually use
EXPORT_SYMBOL.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: John Crispin <john@phrozen.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/13930/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Some configs of mips like xway_defconffig are failing with the error:
arch/mips/lantiq/irq.c:209:2: error: initialization from incompatible
pointer type [-Werror]
"icu",
^
arch/mips/lantiq/irq.c:209:2: error: (near initialization for
'ltq_irq_type.parent_device') [-Werror]
arch/mips/lantiq/irq.c:219:2: error: initialization from incompatible
pointer type [-Werror]
"eiu",
^
arch/mips/lantiq/irq.c:219:2: error: (near initialization for
'ltq_eiu_type.parent_device') [-Werror]
The first member of the "struct irq" is no longer a pointer for the
name.
Fixes: be45beb2df ("genirq: Add runtime power management support for IRQ chips")
Signed-off-by: Sudip Mukherjee <sudip.mukherjee@codethink.co.uk>
Acked-by: John Crispin <john@phrozen.org>
Cc: linux-kernel@vger.kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/13684/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Instead of rewriting the arguments to match the UHI spec, store the
address of a appended or UHI supplied dtb in fw_supplied_dtb.
That way the original bootloader arugments are kept intact while still
making the use of an appended dtb invisible for mach code.
Mach code can still find out if it is an appended dtb by comparing
fw_arg1 with fw_supplied_dtb.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
Cc: Kevin Cernekee <cernekee@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: John Crispin <john@phrozen.org>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Alban Bedel <albeu@free.fr>
Cc: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
Cc: Antony Pavlov <antonynpavlov@gmail.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/13699/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
We used the hardware IRQ number to register the IRQ handler and not the
virtual one. This probably caused some problems because the hardware
IRQ numbers are only unique for each IRQ controller and not in the
system. The virtual IRQ number is managed by Linux and unique in the
system. This was probably the reason there was a gab of 8 IRQ numbers added
before the numbers used for the lantiq IRQ controller. With the current
setup the hardware and the virtual IRQ numbers are the same.
Reported-by: Thomas Langer <thomas.langer@intel.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: John Crispin <john@phrozen.org>
Cc: thomas.langer@intel.com
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/13539/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
We runtime load the available external interrupts into an array and store
the number inside exin_avail. Some of the code however uses MAX_EIU for
looping over the array which may partially be 0. This is a cosmetic fix as
the existing code works as is. It is just nicer to only loop over the array
elements that were actually populated during probe.
Signed-off-by: John Crispin <john@phrozen.org>
Cc: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/13602/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Using of_irq_count to load the irq index from the devicetree is incorrect.
This will cause the kernel to map them regardless, even if they dont
actually get used. Change the code to use of_property_count_u32_elems()
instead which is the correct API to use in this case.
Signed-off-by: John Crispin <john@phrozen.org>
Cc: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/13601/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Using of_irq_count to load the irq index from the devicetree is incorrect.
This will cause the kernel to map them regardless, even if they dont
actually get used. Change the code to use of_property_count_u32_elems()
instead which is the correct API to use in this case.
Signed-off-by: John Crispin <john@phrozen.org>
Cc: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/13601/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Now it is possible to build in no device tree at all and depend on the
boot loader providing one or someone concatenating a device tree to the
end of the image.
This was copied from arch/mips/bmips/Kconfig
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: John Crispin <john@phrozen.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/12899/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This fetches the device tree file like it is specified in the MIPS UHI
interface if one was found. This is also used when the device tree file
was appended to the kernel image with cat.
This code is copied from arch/mips/bmips/setup.c.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: John Crispin <john@phrozen.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/12898/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Seval of-enabled machines (bmips, lantiq, xlp, pistachio, ralink) copied
the arguments from dtb to arcs_command_line to prevent the kernel from
overwriting them.
Since there is now an option to keep the dtb arguments, default to the
new option remove the "backup" to arcs_command_line in case of USE_OF is
enabled, except for those platforms that still take the bootloader
arguments or do not use any at all.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
Cc: linux-mips@linux-mips.org
Cc: Kevin Cernekee <cernekee@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Zubair Lutfullah Kakakhel <Zubair.Kakakhel@imgtec.com>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: John Crispin <blogic@openwrt.org>
Cc: Ganesan Ramalingam <ganesanr@broadcom.com>
Cc: Jayachandran C <jchandra@broadcom.com>
Cc: Andrew Bresticker <abrestic@chromium.org>
Cc: James Hartley <james.hartley@imgtec.com>
Patchwork: https://patchwork.linux-mips.org/patch/11285/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
There is a DWC2 USB core in these SoCs. To make USB work we need to first
reset and power the state machine. These are SoC specific registers and
not part of the actual USB core.
Signed-off-by: Antti Seppälä <a.seppala@gmail.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/11449/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Some configurations of AR9 reported the incorrect speed for the fpi bus.
Signed-off-by: Ben Mulvihill <ben.mulvihill@gmail.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/11448/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
request_mem_region() returns a pointer and not an integer with an error
value. A check for "< 0" on a pointer will cause problems, replace it
with not null checks instead. This was found with sparse.
Signed-off-by: Hauke Mehrtens <hauke.mehrtens@lantiq.com>
Acked-by: John Crispin <blogic@openwrt.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/11395/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This adds the PUM bits for USB and SDIO devices
Signed-off-by: Hauke Mehrtens <hauke.mehrtens@lantiq.com>
Acked-by: John Crispin <blogic@openwrt.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/11387/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
When the SoC starts up most of the devices should be deactivated by the
PMU, they should be activated when they get used by their drivers. Some
devices should not get deactivate at startup like the serial, register
them in a special way.
Signed-off-by: Hauke Mehrtens <hauke.mehrtens@lantiq.com>
Acked-by: John Crispin <blogic@openwrt.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/11386/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This add detection of some clocks on the ar10 and grx390.
Signed-off-by: Hauke Mehrtens <hauke.mehrtens@lantiq.com>
Acked-by: John Crispin <blogic@openwrt.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/11385/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This adds support for setting the PMU register on the AR10 and GRX390.
Signed-off-by: Hauke Mehrtens <hauke.mehrtens@lantiq.com>
Acked-by: John Crispin <blogic@openwrt.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/11382/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The PMU register are accessed in a non atomic way and they could be
accessed by different threads simultaneously, which could cause
problems this patch adds locking around the PMU registers. In
addition we now also wait till the PMU is actually deactivated.
[ralf@linux-mips.org: Fix spelling mistake in commit message as noticed
by Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>.]
Signed-off-by: Hauke Mehrtens <hauke.mehrtens@lantiq.com>
Acked-by: John Crispin <blogic@openwrt.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/11381/
Patchwork: https://patchwork.linux-mips.org/patch/11396/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This adds a basic implementation of clk_round_rate()
The clk_round_rate() function is called by multiple drivers and
subsystems now and the lantiq clk driver is supposed to export this,
but doesn't do so, this causes linking problems like this one:
ERROR: "clk_round_rate" [drivers/media/v4l2-core/videodev.ko] undefined!
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: John Crispin <blogic@openwrt.org>
Cc: <stable@vger.kernel.org> # 4.1+
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/11358/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The majority of SMP platforms handle their IPIs through do_IRQ()
which calls irq_{enter/exit}(). When a call function IPI is received,
smp_call_function_interrupt() is called which also calls
irq_{enter,exit}(), meaning irq_count is raised twice.
When tick broadcasting is used (which is implemented via a call
function IPI), this incorrectly causes all CPU idle time on the core
receiving broadcast ticks to be accounted as time spent servicing
IRQs, as account_process_tick() will account as such if irq_count is
greater than 1. This results in 100% CPU usage being reported on a
core which receives its ticks via broadcast.
This patch removes the SMP smp_call_function_interrupt() wrapper which
calls irq_{enter,exit}(). Platforms which handle their IPIs through
do_IRQ() now call generic_smp_call_function_interrupt() directly to
avoid incrementing irq_count a second time. Platforms which don't
(loongson, sgi-ip27, sibyte) call generic_smp_call_function_interrupt()
wrapped in irq_{enter,exit}().
Signed-off-by: Alex Smith <alex.smith@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/10770/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
On OCTEON the function is non-trivial and we can potentially even save
some memory.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Acked-by: David Daney <david.daney@cavium.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/9338/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes, just
removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There are
some ath9k patches coming in through this tree that have been acked by
the wireless maintainers as they relied on the debugfs changes.
Everything has been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlSOD20ACgkQMUfUDdst+ylLPACg2QrW1oHhdTMT9WI8jihlHVRM
53kAoLeteByQ3iVwWurwwseRPiWa8+MI
=OVRS
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core update from Greg KH:
"Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes,
just removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There
are some ath9k patches coming in through this tree that have been
acked by the wireless maintainers as they relied on the debugfs
changes.
Everything has been in linux-next for a while"
* tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (324 commits)
Revert "ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries"
fs: debugfs: add forward declaration for struct device type
firmware class: Deletion of an unnecessary check before the function call "vunmap"
firmware loader: fix hung task warning dump
devcoredump: provide a one-way disable function
device: Add dev_<level>_once variants
ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries
ath: use seq_file api for ath9k debugfs files
debugfs: add helper function to create device related seq_file
drivers/base: cacheinfo: remove noisy error boot message
Revert "core: platform: add warning if driver has no owner"
drivers: base: support cpu cache information interface to userspace via sysfs
drivers: base: add cpu_device_create to support per-cpu devices
topology: replace custom attribute macros with standard DEVICE_ATTR*
cpumask: factor out show_cpumap into separate helper function
driver core: Fix unbalanced device reference in drivers_probe
driver core: fix race with userland in device_add()
sysfs/kernfs: make read requests on pre-alloc files use the buffer.
sysfs/kernfs: allow attributes to request write buffer be pre-allocated.
fs: sysfs: return EGBIG on write if offset is larger than file size
...
The code to detect unfused SoCs was broken due to missing register masking.
Signed-off-by: Thomas Langer <thomas.langer@lantiq.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/8049/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This is a regression caused by:
commit afb46f7996
Author: Rob Herring <robh@kernel.org>
Date: Wed Apr 2 19:07:24 2014 -0500
mips: ralink: convert to use unflatten_and_copy_device_tree
Make the of init code reuse the cmdline defined inside the dts.
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/8048/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The eiu init failed as the irq_domain was not yet available.
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/8047/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The voice and dsl drivers need to know which SoC we are running on.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Patchwork: http://patchwork.linux-mips.org/patch/8046/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
VR9 needs different firmware files for the various phy/soc revisions. Some
boards are ship with older and newer SoC revisions. To be able to boot a single
image on all versions we need to define both firmware files inside the
devicetree.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/8045/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
A reboot sometimes lead to a none working phy. An explicit reboot fixes the
problem.
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/8044/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add a reset-controller binding for the reset registers found on the lantiq
SoC.
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/8043/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The Lantiq SoCs have a 2nd mips core called "voice mips macro core (vmmc)"
which is used to run the voice firmware. This driver allows us to register
a chunk of memory that the voice driver can later use for the 2nd core.
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/8042/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The hardware perf event driver and oprofile interpret the global
cp0_perfcount_irq differently: in the hardware perf event driver
it is an offset from MIPS_CPU_IRQ_BASE and in oprofile it is the
actual IRQ number. This still works most of the time since
MIPS_CPU_IRQ_BASE is usually 0, but is clearly wrong. Since the
performance counter interrupt may vary from platform to platform
like the C0 timer interrupt, add the optional get_c0_perfcount_int
hook which returns the IRQ number of the performance counter.
The hook should return < 0 if the performance counter interrupt is
shared with the timer. If the hook is not present, the CPU vector
reported in C0_IntCtl (cp0_perfcount_irq) is used.
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Reviewed-by: Qais Yousef <qais.yousef@imgtec.com>
Tested-by: Qais Yousef <qais.yousef@imgtec.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Andrew Bresticker <abrestic@chromium.org>
Cc: Jeffrey Deans <jeffrey.deans@imgtec.com>
Cc: Markos Chandras <markos.chandras@imgtec.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Qais Yousef <qais.yousef@imgtec.com>
Cc: Jonas Gorski <jogo@openwrt.org>
Cc: John Crispin <blogic@openwrt.org>
Cc: David Daney <ddaney.cavm@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/7805/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Pull MIPS updates from Ralf Baechle:
"This is the MIPS pull request for the next kernel:
- Zubair's patch series adds CMA support for MIPS. Doing so it also
touches ARM64 and x86.
- remove the last instance of IRQF_DISABLED from arch/mips
- updates to two of the MIPS defconfig files.
- cleanup of how cache coherency bits are handled on MIPS and
implement support for write-combining.
- platform upgrades for Alchemy
- move MIPS DTS files to arch/mips/boot/dts/"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (24 commits)
MIPS: ralink: remove deprecated IRQF_DISABLED
MIPS: pgtable.h: Implement the pgprot_writecombine function for MIPS
MIPS: cpu-probe: Set the write-combine CCA value on per core basis
MIPS: pgtable-bits: Define the CCA bit for WC writes on Ingenic cores
MIPS: pgtable-bits: Move the CCA bits out of the core's ifdef blocks
MIPS: DMA: Add cma support
x86: use generic dma-contiguous.h
arm64: use generic dma-contiguous.h
asm-generic: Add dma-contiguous.h
MIPS: BPF: Add new emit_long_instr macro
MIPS: ralink: Move device-trees to arch/mips/boot/dts/
MIPS: Netlogic: Move device-trees to arch/mips/boot/dts/
MIPS: sead3: Move device-trees to arch/mips/boot/dts/
MIPS: Lantiq: Move device-trees to arch/mips/boot/dts/
MIPS: Octeon: Move device-trees to arch/mips/boot/dts/
MIPS: Add support for building device-tree binaries
MIPS: Create common infrastructure for building built-in device-trees
MIPS: SEAD3: Enable DEVTMPFS
MIPS: SEAD3: Regenerate defconfigs
MIPS: Alchemy: DB1300: Add touch penirq support
...
Move the Lantiq device-trees to arch/mips/boot/dts/ and update the
Makefiles accordingly. There is currently only a single Lantiq
device-tree (EASY50712), and it's required to be built into the kernel,
so select BUILTIN_DTB for it.
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Kumar Gala <galak@codeaurora.org>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: David Daney <david.daney@cavium.com>
Cc: John Crispin <blogic@openwrt.org>
Cc: Jayachandran C <jchandra@broadcom.com>
Cc: Qais Yousef <qais.yousef@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Cc: devicetree@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/7559/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Pull MIPS updates from Ralf Baechle:
- three fixes for 3.15 that didn't make it in time
- limited Octeon 3 support.
- paravirtualization support
- improvment to platform support for Netlogix SOCs.
- add support for powering down the Malta eval board in software
- add many instructions to the in-kernel microassembler.
- add support for the BPF JIT.
- minor cleanups of the BCM47xx code.
- large cleanup of math emu code resulting in significant code size
reduction, better readability of the code and more accurate
emulation.
- improvments to the MIPS CPS code.
- support C3 power status for the R4k count/compare clock device.
- improvments to the GIO support for older SGI workstations.
- increase number of supported CPUs to 256; this can be reached on
certain embedded multithreaded ccNUMA configurations.
- various small cleanups, updates and fixes
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (173 commits)
MIPS: IP22/IP28: Improve GIO support
MIPS: Octeon: Add twsi interrupt initialization for OCTEON 3XXX, 5XXX, 63XX
DEC: Document the R4k MB ASIC mini interrupt controller
DEC: Add self as the maintainer
MIPS: Add microMIPS MSA support.
MIPS: Replace calls to obsolete strict_strto call with kstrto* equivalents.
MIPS: Replace obsolete strict_strto call with kstrto
MIPS: BFP: Simplify code slightly.
MIPS: Call find_vma with the mmap_sem held
MIPS: Fix 'write_msa_##' inline macro.
MIPS: Fix MSA toolchain support detection.
mips: Update the email address of Geert Uytterhoeven
MIPS: Add minimal defconfig for mips_paravirt
MIPS: Enable build for new system 'paravirt'
MIPS: paravirt: Add pci controller for virtio
MIPS: Add code for new system 'paravirt'
MIPS: Add functions for hypervisor call
MIPS: OCTEON: Add OCTEON3 to __get_cpu_type
MIPS: Add function get_ebase_cpunum
MIPS: Add minimal support for OCTEON3 to c-r4k.c
...
- Another round of clean-up of FDT related code in architecture code.
This removes knowledge of internal FDT details from most architectures
except powerpc.
- Conversion of kernel's custom FDT parsing code to use libfdt.
- DT based initialization for generic serial earlycon. The introduction
of generic serial earlycon support went in thru tty tree.
- Improve the platform device naming for DT probed devices to ensure
unique naming and use parent names instead of a global index.
- Fix a race condition in of_update_property.
- Unify the various linker section OF match tables and fix several
function prototype errors.
- Update platform_get_irq_byname to work in deferred probe cases.
- 2 binding doc updates
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJTjzgyAAoJEMhvYp4jgsXiFsUH/1PMTGo8CyD62VQD5ZKdAoW+
Fq6vCiRQ8assF5i5ZLcW1DqhjtoRaCKYhVbRKa5lj7cZdjlSpacI/qQPrF5Br2Ii
bTE3Ff/AQwipQaz/Bj7HqJCgGwfWK8xdfgW0abKsyXMWDN86Bov/zzeu8apmws0x
H1XjJRgnc/rzM4m9ny6+lss0iq6YL54SuTYNzHR33+Ywxls69SfHXIhCW0KpZcBl
5U3YUOomt40GfO46sxFA4xApAhypEK4oVq7asyiA2ArTZ/c2Pkc9p5CBqzhDLmlq
yioWTwHIISv0q+yMLCuQrVGIsbUDkQyy7RQ15z6U+/e/iGO/M+j3A5yxMc3qOi4=
=Onff
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux into next
Pull DeviceTree updates from Rob Herring:
- Another round of clean-up of FDT related code in architecture code.
This removes knowledge of internal FDT details from most
architectures except powerpc.
- Conversion of kernel's custom FDT parsing code to use libfdt.
- DT based initialization for generic serial earlycon. The
introduction of generic serial earlycon support went in through the
tty tree.
- Improve the platform device naming for DT probed devices to ensure
unique naming and use parent names instead of a global index.
- Fix a race condition in of_update_property.
- Unify the various linker section OF match tables and fix several
function prototype errors.
- Update platform_get_irq_byname to work in deferred probe cases.
- 2 binding doc updates
* tag 'devicetree-for-3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (58 commits)
of: handle NULL node in next_child iterators
of/irq: provide more wrappers for !CONFIG_OF
devicetree: bindings: Document micrel vendor prefix
dt: bindings: dwc2: fix required value for the phy-names property
of_pci_irq: kill useless variable in of_irq_parse_pci()
of/irq: do irq resolution in platform_get_irq_byname()
of: Add a testcase for of_find_node_by_path()
of: Make of_find_node_by_path() handle /aliases
of: Create unlocked version of for_each_child_of_node()
lib: add glibc style strchrnul() variant
of: Handle memory@0 node on PPC32 only
pci/of: Remove dead code
of: fix race between search and remove in of_update_property()
of: Use NULL for pointers
of: Stop naming platform_device using dcr address
of: Ensure unique names without sacrificing determinism
tty/serial: pl011: add DT based earlycon support
of/fdt: add FDT serial scanning for earlycon
of/fdt: add FDT address translation support
serial: earlycon: add DT support
...
A few platforms lack a 'device_type = "memory"' for their memory
nodes, relying on an old ppc quirk in order to discover its memory.
Add the missing data so that all parsing code can find memory nodes
correctly.
Signed-off-by: Leif Lindholm <leif.lindholm@linaro.org>
Acked-by: John Crispin <blogic@openwrt.org>
Signed-off-by: Grant Likely <grant.likely@linaro.org>
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: <stable@vger.kernel.org>
Cc: gaurav.minocha@alumni.ubc.ca
Patchwork: https://patchwork.linux-mips.org/patch/6989/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Nobody is maintaining SMTC anymore and there also seems to be no userbase.
Which is a pity - the SMTC technology primarily developed by Kevin D.
Kissell <kevink@paralogos.com> is an ingenious demonstration for the MT
ASE's power and elegance.
Based on Markos Chandras <Markos.Chandras@imgtec.com> patch
https://patchwork.linux-mips.org/patch/6719/ which while very similar did
no longer apply cleanly when I tried to merge it plus some additional
post-SMTC cleanup - SMTC was a feature as tricky to remove as it was to
merge once upon a time.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
A few platforms lack a 'device_type = "memory"' for their memory
nodes, relying on an old ppc quirk in order to discover its memory.
Add the missing data so that all parsing code can find memory nodes
correctly.
Signed-off-by: Leif Lindholm <leif.lindholm@linaro.org>
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: <stable@vger.kernel.org>
Acked-by: John Crispin <blogic@openwrt.org>
Signed-off-by: Grant Likely <grant.likely@linaro.org>
Unify the various architectures __dtb_start and __dtb_end definitions
moving them into of_fdt.h.
Signed-off-by: Rob Herring <robh@kernel.org>
Acked-by: Vineet Gupta <vgupta@synopsys.com>
Acked-by: James Hogan <james.hogan@imgtec.com>
Tested-by: Michal Simek <michal.simek@xilinx.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Jonas Bonn <jonas@southpole.se>
Cc: Chris Zankel <chris@zankel.net>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Cc: linux-metag@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: linux@lists.openrisc.net
Cc: linux-xtensa@linux-xtensa.org
Tested-by: Grant Likely <grant.likely@linaro.org>
Tested-by: Stephen Chivers <schivers@csc.com>
The architecture code does not need to access the internals of the FDT
blob directly, so make the pointers to it void * and use char arrays
for section variables.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Tested-by: Grant Likely <grant.likely@linaro.org>
The existing code is buggy because built-in DTBs are in init memory.
Fix this by using the unflatten_and_copy_device_tree function.
This removes all accesses to FDT header data by the arch code.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Tested-by: Grant Likely <grant.likely@linaro.org>
None of these files are actually using any __init type directives
and hence don't need to include <linux/init.h>. Most are just a
left over from __devinit and __cpuinit removal, or simply due to
code getting copied from one driver to the next.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6320/
devm_ioremap_resource does sanity checks on the given resource. No need to
duplicate this in the driver.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6348/
usual for this cycle with lots of clean-up.
- Cross arch clean-up and consolidation of early DT scanning code.
- Clean-up and removal of arch prom.h headers. Makes arch specific
prom.h optional on all but Sparc.
- Addition of interrupts-extended property for devices connected to
multiple interrupt controllers.
- Refactoring of DT interrupt parsing code in preparation for deferred
probe of interrupts.
- ARM cpu and cpu topology bindings documentation.
- Various DT vendor binding documentation updates.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQEcBAABAgAGBQJSgPQ4AAoJEMhvYp4jgsXif28H/1WkrXq5+lCFQZF8nbYdE2h0
R8PsfiJJmAl6/wFgQTsRel+ScMk2hiP08uTyqf2RLnB1v87gCF7MKVaLOdONfUDi
huXbcQGWCmZv0tbBIklxJe3+X3FIJch4gnyUvPudD1m8a0R0LxWXH/NhdTSFyB20
PNjhN/IzoN40X1PSAhfB5ndWnoxXBoehV/IVHVDU42vkPVbVTyGAw5qJzHW8CLyN
2oGTOalOO4ffQ7dIkBEQfj0mrgGcODToPdDvUQyyGZjYK2FY2sGrjyquir6SDcNa
Q4gwatHTu0ygXpyphjtQf5tc3ZCejJ/F0s3olOAS1ahKGfe01fehtwPRROQnCK8=
=GCbY
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull devicetree updates from Rob Herring:
"DeviceTree updates for 3.13. This is a bit larger pull request than
usual for this cycle with lots of clean-up.
- Cross arch clean-up and consolidation of early DT scanning code.
- Clean-up and removal of arch prom.h headers. Makes arch specific
prom.h optional on all but Sparc.
- Addition of interrupts-extended property for devices connected to
multiple interrupt controllers.
- Refactoring of DT interrupt parsing code in preparation for
deferred probe of interrupts.
- ARM cpu and cpu topology bindings documentation.
- Various DT vendor binding documentation updates"
* tag 'devicetree-for-3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (82 commits)
powerpc: add missing explicit OF includes for ppc
dt/irq: add empty of_irq_count for !OF_IRQ
dt: disable self-tests for !OF_IRQ
of: irq: Fix interrupt-map entry matching
MIPS: Netlogic: replace early_init_devtree() call
of: Add Panasonic Corporation vendor prefix
of: Add Chunghwa Picture Tubes Ltd. vendor prefix
of: Add AU Optronics Corporation vendor prefix
of/irq: Fix potential buffer overflow
of/irq: Fix bug in interrupt parsing refactor.
of: set dma_mask to point to coherent_dma_mask
of: add vendor prefix for PHYTEC Messtechnik GmbH
DT: sort vendor-prefixes.txt
of: Add vendor prefix for Cadence
of: Add empty for_each_available_child_of_node() macro definition
arm/versatile: Fix versatile irq specifications.
of/irq: create interrupts-extended property
microblaze/pci: Drop PowerPC-ism from irq parsing
of/irq: Create of_irq_parse_and_map_pci() to consolidate arch code.
of/irq: Use irq_of_parse_and_map()
...
Panic() is going to add a \n itself and it's annoying if a panic message rolls
of the screen on a device with no scrollback.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
In preparation of removing prom.h include by of.h, add explicit includes.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Grant Likely <grant.likely@linaro.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
The clocks of the serial ports were not setup properly.
Signed-off-by: Thomas Langer <thomas.langer@lantiq.com>
Acked-by: John Crispin <blogic@openwrt.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5659/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
commit 3747069b25e419f6b51395f48127e9812abc3596 upstream.
The __cpuinit type of throwaway sections might have made sense
some time ago when RAM was more constrained, but now the savings
do not offset the cost and complications. For example, the fix in
commit 5e427ec2d0 ("x86: Fix bit corruption at CPU resume time")
is a good example of the nasty type of bugs that can be created
with improper use of the various __init prefixes.
After a discussion on LKML[1] it was decided that cpuinit should go
the way of devinit and be phased out. Once all the users are gone,
we can then finally remove the macros themselves from linux/init.h.
Note that some harmless section mismatch warnings may result, since
notify_cpu_starting() and cpu_up() are arch independent (kernel/cpu.c)
and are flagged as __cpuinit -- so if we remove the __cpuinit from
the arch specific callers, we will also get section mismatch warnings.
As an intermediate step, we intend to turn the linux/init.h cpuinit
related content into no-ops as early as possible, since that will get
rid of these warnings. In any case, they are temporary and harmless.
Here, we remove all the MIPS __cpuinit from C code and __CPUINIT
from asm files. MIPS is interesting in this respect, because there
are also uasm users hiding behind their own renamed versions of the
__cpuinit macros.
[1] https://lkml.org/lkml/2013/5/20/589
[ralf@linux-mips.org: Folded in Paul's followup fix.]
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5494/
Patchwork: https://patchwork.linux-mips.org/patch/5495/
Patchwork: https://patchwork.linux-mips.org/patch/5509/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
'compatible' is used by strlen() in __of_device_is_compatible().
Ensure strings are always '\0' terminated.
'of_ids is not a structure in "include/uapi/*", so no need to initialize
it completly; using strlcpy() instead of strncpy() will do.
Signed-off-by: Chen Gang <gang.chen@asianux.com>
Acked-by: John Crispin <blogic@openwrt.org>
Cc: linux-mips@linux-mips.org
Cc: Linux-Arch <linux-arch@vger.kernel.org>
Patchwork: https://patchwork.linux-mips.org/patch/5329/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Pull devm usage cleanup from Wolfram Sang:
"Lately, I have been experimenting how to improve the devm interface to
make writing device drivers easier and less error prone while also
getting rid of its subtle issues. I think it has more potential but
still needs work and definately conistency, especiall in its usage.
The first thing I come up with is a low hanging fruit regarding
devm_ioremap_resouce(). This function already checks if the passed
resource is valid and gives an error message if not. So, we can
remove similar checks from the drivers and get rid of a bit of code
and a number of inconsistent error strings.
This series only removes the unneeded check iff devm_ioremap_resource
follows platform_get_resource directly. The previous version tried to
shuffle code if needed, too, what lead to an embarrasing bug. It
turned out to me that shuffling code for all cases found will make the
automated script too complex, so I am unsure if an automated cleanup
is the proper tool for this case. Removing the easy stuff seems
worthwhile to me, though.
Despite various architectures and platform dependencies, I managed to
compile test 45 out of 57 modified files locally using heuristics and
defconfigs."
Pulled because: 296 deletions, 0 additions.
* 'devm_no_resource_check' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (33 commits)
sound/soc/kirkwood: don't check resource with devm_ioremap_resource
sound/soc/fsl: don't check resource with devm_ioremap_resource
arch/mips/lantiq/xway: don't check resource with devm_ioremap_resource
arch/arm/plat-samsung: don't check resource with devm_ioremap_resource
arch/arm/mach-tegra: don't check resource with devm_ioremap_resource
drivers/watchdog: don't check resource with devm_ioremap_resource
drivers/w1/masters: don't check resource with devm_ioremap_resource
drivers/video/omap2/dss: don't check resource with devm_ioremap_resource
drivers/video/omap2: don't check resource with devm_ioremap_resource
drivers/usb/phy: don't check resource with devm_ioremap_resource
drivers/usb/host: don't check resource with devm_ioremap_resource
drivers/usb/gadget: don't check resource with devm_ioremap_resource
drivers/usb/chipidea: don't check resource with devm_ioremap_resource
drivers/thermal: don't check resource with devm_ioremap_resource
drivers/staging/nvec: don't check resource with devm_ioremap_resource
drivers/staging/dwc2: don't check resource with devm_ioremap_resource
drivers/spi: don't check resource with devm_ioremap_resource
drivers/rtc: don't check resource with devm_ioremap_resource
drivers/pwm: don't check resource with devm_ioremap_resource
drivers/pinctrl: don't check resource with devm_ioremap_resource
...
devm_ioremap_resource does sanity checks on the given resource. No need to
duplicate this in the driver.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: John Crispin <blogic@openwrt.org>
Pull MIPS updates from Ralf Baechle:
o Add basic support for the Mediatek/Ralink Wireless SoC family.
o The Qualcomm Atheros platform is extended by support for the new
QCA955X SoC series as well as a bunch of patches that get the code
ready for OF support.
o Lantiq and BCM47XX platform have a few improvements and bug fixes.
o MIPS has sent a few patches that get the kernel ready for the
upcoming microMIPS support.
o The rest of the series is made up of small bug fixes and cleanups
that relate to various parts of the MIPS code. The biggy in there is
a whitespace cleanup. After I was sent another set of whitespace
cleanup patches I decided it was the time to clean the whitespace
"issues" for once and and that touches many files below arch/mips/.
Fix up silly conflicts, mostly due to whitespace cleanups.
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (105 commits)
MIPS: Quit exporting kernel internel break codes to uapi/asm/break.h
MIPS: remove broken conditional inside vpe loader code
MIPS: SMTC: fix implicit declaration of set_vi_handler
MIPS: early_printk: drop __init annotations
MIPS: Probe for and report hardware virtualization support.
MIPS: ath79: add support for the Qualcomm Atheros AP136-010 board
MIPS: ath79: add USB controller registration code for the QCA955X SoCs
MIPS: ath79: add PCI controller registration code for the QCA955X SoCs
MIPS: ath79: add WMAC registration code for the QCA955X SoCs
MIPS: ath79: register UART for the QCA955X SoCs
MIPS: ath79: add QCA955X specific glue to ath79_device_reset_{set, clear}
MIPS: ath79: add GPIO setup code for the QCA955X SoCs
MIPS: ath79: add IRQ handling code for the QCA955X SoCs
MIPS: ath79: add clock setup code for the QCA955X SoCs
MIPS: ath79: add SoC detection code for the QCA955X SoCs
MIPS: ath79: add early printk support for the QCA955X SoCs
MIPS: ath79: fix WMAC IRQ resource assignment
mips: reserve elfcorehdr
mips: Make sure kernel memory is in iomem
MIPS: ath79: use dynamically allocated USB platform devices
...
Here is the big driver core merge for 3.9-rc1
There are two major series here, both of which touch lots of drivers all
over the kernel, and will cause you some merge conflicts:
- add a new function called devm_ioremap_resource() to properly be
able to check return values.
- remove CONFIG_EXPERIMENTAL
If you need me to provide a merged tree to handle these resolutions,
please let me know.
Other than those patches, there's not much here, some minor fixes and
updates.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlEmV0cACgkQMUfUDdst+yncCQCfbmnQZju7kzWXk6PjdFuKspT9
weAAoMCzcAtEzzc4LXuUxxG/sXBVBCjW
=yWAQ
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core patches from Greg Kroah-Hartman:
"Here is the big driver core merge for 3.9-rc1
There are two major series here, both of which touch lots of drivers
all over the kernel, and will cause you some merge conflicts:
- add a new function called devm_ioremap_resource() to properly be
able to check return values.
- remove CONFIG_EXPERIMENTAL
Other than those patches, there's not much here, some minor fixes and
updates"
Fix up trivial conflicts
* tag 'driver-core-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (221 commits)
base: memory: fix soft/hard_offline_page permissions
drivercore: Fix ordering between deferred_probe and exiting initcalls
backlight: fix class_find_device() arguments
TTY: mark tty_get_device call with the proper const values
driver-core: constify data for class_find_device()
firmware: Ignore abort check when no user-helper is used
firmware: Reduce ifdef CONFIG_FW_LOADER_USER_HELPER
firmware: Make user-mode helper optional
firmware: Refactoring for splitting user-mode helper code
Driver core: treat unregistered bus_types as having no devices
watchdog: Convert to devm_ioremap_resource()
thermal: Convert to devm_ioremap_resource()
spi: Convert to devm_ioremap_resource()
power: Convert to devm_ioremap_resource()
mtd: Convert to devm_ioremap_resource()
mmc: Convert to devm_ioremap_resource()
mfd: Convert to devm_ioremap_resource()
media: Convert to devm_ioremap_resource()
iommu: Convert to devm_ioremap_resource()
drm: Convert to devm_ioremap_resource()
...
This code makes the irqs used by the EIU loadable from the DT. Additionally we
add a helper that allows the pinctrl layer to map external irqs to real irq
numbers.
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/4818/
Explicitly enable the clock gate of the internal GPHYs found on xrx200.
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/4816/
The Lantiq DSL SoCs have an internal networking processor. Add code to read
the static clock rate.
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/4815/
Having received another series of whitespace patches I decided to do this
once and for all rather than dealing with this kind of patches trickling
in forever.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The introduction of the OF support broke the cp0_perfcount_irq mapping. This
resulted in oprofile not working anymore.
Offending commit is :
commit 3645da0276
Author: John Crispin <blogic@openwrt.org>
Date: Tue Apr 17 10:18:32 2012 +0200
OF: MIPS: lantiq: implement irq_domain support
Signed-off-by: Conor O'Gorman <i@conorogorman.net>
Signed-off-by: John Crispin <blogic@openwrt.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/4875/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Convert all uses of devm_request_and_ioremap() to the newly introduced
devm_ioremap_resource() which provides more consistent error handling.
devm_ioremap_resource() provides its own error messages so all explicit
error messages can be removed from the failure code paths.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CONFIG_HOTPLUG is going away as an option. As a result, the __dev*
markings need to be removed.
This change removes the use of __devinit, __devexit_p, __devinitdata,
and __devexit from these drivers.
Based on patches originally written by Bill Pemberton, but redone by me
in order to handle some of the coding style issues better, by hand.
Cc: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull MIPS updates from Ralf Baechle:
"The MIPS bits for 3.8. This also includes a bunch fixes that were
sitting in the linux-mips.org git tree for a long time. This pull
request contains updates to several OCTEON drivers and the board
support code for BCM47XX, BCM63XX, XLP, XLR, XLS, lantiq, Loongson1B,
updates to the SSB bus support, MIPS kexec code and adds support for
kdump.
When pulling this, there are two expected merge conflicts in
include/linux/bcma/bcma_driver_chipcommon.h which are trivial to
resolve, just remove the conflict markers and keep both alternatives."
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (90 commits)
MIPS: PMC-Sierra Yosemite: Remove support.
VIDEO: Newport Fix console crashes
MIPS: wrppmc: Fix build of PCI code.
MIPS: IP22/IP28: Fix build of EISA code.
MIPS: RB532: Fix build of prom code.
MIPS: PowerTV: Fix build.
MIPS: IP27: Correct fucked grammar in ops-bridge.c
MIPS: Highmem: Fix build error if CONFIG_DEBUG_HIGHMEM is disabled
MIPS: Fix potencial corruption
MIPS: Fix for warning from FPU emulation code
MIPS: Handle COP3 Unusable exception as COP1X for FP emulation
MIPS: Fix poweroff failure when HOTPLUG_CPU configured.
MIPS: MT: Fix build with CONFIG_UIDGID_STRICT_TYPE_CHECKS=y
MIPS: Remove unused smvp.h
MIPS/EDAC: Improve OCTEON EDAC support.
MIPS: OCTEON: Add definitions for OCTEON memory contoller registers.
MIPS: OCTEON: Add OCTEON family definitions to octeon-model.h
ata: pata_octeon_cf: Use correct byte order for DMA in when built little-endian.
MIPS/OCTEON/ata: Convert pata_octeon_cf.c to use device tree.
MIPS: Remove usage of CEVT_R4K_LIB config option.
...
All architectures that use cmd_dtc do so in almost the same way. Create
a central build rule to avoid duplication. The one difference is that
most current uses of dtc build $(obj)/%.dtb from $(src)/dts/%.dts rather
than building the .dtb in the same directory as the .dts file. This
difference will be eliminated arch-by-arch in future patches.
MIPS is the exception here; it already uses the exact same rule as the
new common rule, so the duplicate is removed in this patch to avoid any
conflict. arch/mips changes courtesy of Ralf Baechle.
Update Documentation/kbuild to remove the explicit call to cmd_dtc from
the example, now that the rule exists in a centralized location.
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Olof Johansson <olof@lixom.net>
Cc: Russell King <linux@arm.linux.org.uk>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Cc: Jonas Bonn <jonas@southpole.se>
Cc: linux@lists.openrisc.net
Cc: Aurelien Jacquiot <a-jacquiot@ti.com>
Cc: linux-c6x-dev@linux-c6x.org
Cc: Mark Salter <msalter@redhat.com>
Cc: Michal Simek <monstr@monstr.eu>
Cc: microblaze-uclinux@itee.uq.edu.au
Cc: Chris Zankel <chris@zankel.net>
Cc: linux-xtensa@linux-xtensa.org
Cc: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
The internal GPHYs need a firmware blob to function properly. This patch adds
the code needed to request the blob and load it to the PHY.
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/4523
The XRX200 family of SoCs has embedded gigabit PHYs. This patch adds code to
boot them up.
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/4522
Print the hardware revision and port/channel info when starting the dma core.
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/4520
