This patch adds minimal support and build configuration for TI8148 EVM. Also
adds support for low level debugging on UART1 console on the EVM.
Note that existing TI8168 EVM file (board-ti8168evm.c) is updated with machine
info for TI8148 EVM.
Signed-off-by: Hemant Pedanekar <hemantp@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
OMAP4 SDP/Blaze boards have onboard digital microphones.
Register the platform device for the dmic-codec to be
able to use the microphones.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add memory timing info regarding the 200 MHz memory in sdram-nokia.
Note that 100 MHz mode uses these same timings too.
Signed-off-by: Igor Dmitriev <ext-dmitriev.igor@nokia.com>
Signed-off-by: Eduardo Valentin <eduardo.valentin@nokia.com>
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
[tony@atomide.com: updated comments for 100 MHz timings]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Enable TSC2005 touchscreen driver on the RX-51 board by providing the
needed platform data.
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Reviewed-by: Sebastian Reichel <sre@debian.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
OMAP pin mux configuration API has been used incorrectly resulting
in wrong mux mode set for several DSS pins.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
USB hub is not functional until is reset.
Reset the USB hub on SB-T35.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
[tony@atomide.com: updated subject]
Signed-off-by: Tony Lindgren <tony@atomide.com>
TWL4030 audio codec is not being registered if no platform data is
supplied. Provide platform data for the TWL4030 audio codec.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
[tony@atomide.com: updated subject]
Signed-off-by: Tony Lindgren <tony@atomide.com>
cm-t35 DSS suplies are connected to VIO.
In fact, TPS65930 does not have VPLL2.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
[tony@atomide.com: updated subject]
Signed-off-by: Tony Lindgren <tony@atomide.com>
ads7846 driver fails to find the regulator supply and
as a result the touchscreen is not working.
Fix this by adding a regulator supply for the ads7846 driver.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
[tony@atomide.com: updated subject]
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch adds cpu type, macros for identification of TI814X device.
Signed-off-by: Hemant Pedanekar <hemantp@ti.com>
[tony@atomide.com: left out CK_TI814X for now]
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch updates existing macros, functions used for TI816X, to enable
addition of other SoCs belonging to TI81XX family (e.g., TI814X).
The approach taken is to use TI81XX/ti81xx for code/data going to be common
across all TI81XX devices.
cpu_is_ti81xx() is introduced to handle code common across TI81XX devices.
In addition, ti8168_evm_map_io() is now replaced with ti81xx_map_io() and moved
in mach-omap2/common.c as same will be used for TI814X and is not board
specific.
Signed-off-by: Hemant Pedanekar <hemantp@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
allow for the omap4430 es2.3 revision to be recognized in the
omap4_check_revision() function.
most aspects of all omap4430 es2.x versions are identical, however
a number of small variations such as default pullup or pulldown
resistor configurations vary between revisions.
detailed information on silicon errata for omap4430 revisions can
be found at http://focus.ti.com/pdfs/wtbu/swpz009D.pdf
Signed-off-by: David Anders <x0132446@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch updates the common machine specific source files for
support for AM33XX/AM335x with cpu type, macros for identification of
AM33XX/AM335X device.
Signed-off-by: Afzal Mohammed <afzal@ti.com>
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Tested-by: Kevin Hilman <khilman@ti.com>
[tony@atomide.com: updated for map_io and common.h changes, dropped CK_AM33XX]
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch updates the common platform files with AM335X device
support (AM33XX family).
The approach taken in this patch is,
AM33XX device will be considered as OMAP3 variant, and a separate
SoC class created for AM33XX family of devices with a subclass type
for AM335X device, which is newly added device in the family.
This means, cpu_is_omap34xx(), cpu_is_am33xx() and cpu_is_am335x()
checks will return success on AM335X device.
A kernel config option CONFIG_SOC_OMAPAM33XX is added under OMAP3
to include support for AM33XX build.
Also, cpu_mask and RATE_IN_XXX flags have crossed 8 bit hence
struct clksel_rate.flags, struct prcm_config.flags and cpu_mask
are changed to u16 from u8.
Signed-off-by: Afzal Mohammed <afzal@ti.com>
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Cc: Hemant Pedanekar <hemantp@ti.com>
[tony@atomide.com: left out CK_AM33XX for now]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Now that there is a common way to reset the machine, let's use it
instead of reinventing the wheel in the kexec backend.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Sending IPI_CPU_STOP to a CPU causes it to execute a busy cpu_relax
loop forever. This makes it impossible to kexec successfully on an SMP
system since the secondary CPUs do not reset.
This patch adds a callback to platform_cpu_kill, defined when
CONFIG_HOTPLUG_CPU=y, from the ipi_cpu_stop handling code. This function
currently just returns 1 on all platforms that define it but allows them
to do something more sophisticated in the future.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Tools such as kexec and CPU hotplug require a way to reset the processor
and branch to some code in physical space. This requires various bits of
jiggery pokery with the caches and MMU which, when it goes wrong, tends
to lock up the system.
This patch fleshes out the soft_restart implementation so that it
branches to the reset code using the identity mapping. This requires us
to change to a temporary stack, held within the kernel image as a static
array, to avoid conflicting with the new view of memory.
Signed-off-by: Will Deacon <will.deacon@arm.com>
When disabling the MMU, it is necessary to take out a 1:1 identity map
of the reset code so that it can safely be executed with and without
the MMU active. To avoid the situation where the physical address of the
reset code aliases with the virtual address of the active stack (which
cannot be included in the 1:1 mapping), it is desirable to change to a
new stack at a location which is less likely to alias.
This code adds a new lib function, call_with_stack:
void call_with_stack(void (*fn)(void *), void *arg, void *sp);
which changes the stack to point at the sp parameter, before invoking
fn(arg) with the new stack selected.
Reviewed-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Dave Martin <dave.martin@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
When probing the VIC, the ST variant has a different probing method to
account for the extra interrupts which meant we didn't previously call
vic_register() which registered the irq_domain.
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Jamie Iles <jamie@jamieiles.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds the ARM_LPAE and ARCH_PHYS_ADDR_T_64BIT Kconfig entries
allowing LPAE support to be compiled into the kernel.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Memory banks living outside of the 32-bit physical address
space do not have a 1:1 pa <-> va mapping and therefore the
__va macro may wrap.
This patch ensures that such banks are marked as highmem so
that the Kernel doesn't try to split them up when it sees that
the wrapped virtual address overlaps the vmalloc space.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Nicolas Pitre <nico@linaro.org>
With LPAE, the pgd is a separate page table with entries pointing to the
pmd. The identity_mapping_add() function needs to ensure that the pgd is
populated before populating the pmd level. The do..while blocks now loop
over the pmd in order to have the same implementation for the two page
table formats. The pmd_addr_end() definition has been removed and the
generic one used instead. The pmd clean-up is done in the pgd_free()
function.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
With LPAE, TTBRx registers are 64-bit. The ASID is stored in TTBR0
rather than a separate Context ID register. This patch makes the
necessary changes to handle context switching on LPAE.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
The DFSR and IFSR register format is different when LPAE is enabled. In
addition, DFSR and IFSR have similar definitions for the fault type.
This modifies the fault code to correctly handle the new format.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Similar to the PTE freeing, this patch introduced __pmd_free_tlb() which
invalidates the TLB before freeing a PMD page. This is needed because on
newer processors the entry in the upper page table may be cached by the
TLB and point to random data after the PMD has been freed.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
This patch adds the MMU initialisation for the LPAE page table format.
The swapper_pg_dir size with LPAE is 5 rather than 4 pages. A new
proc-v7-3level.S file contains the TTB initialisation, context switch
and PTE setting code with the LPAE. The TTBRx split is based on the
PAGE_OFFSET with TTBR1 used for the kernel mappings. The 36-bit mappings
(supersections) and a few other memory types in mmu.c are conditionally
compiled.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
This patch modifies the pgd/pmd/pte manipulation functions to support
the 3-level page table format. Since there is no need for an 'ext'
argument to cpu_set_pte_ext(), this patch conditionally defines a
different prototype for this function when CONFIG_ARM_LPAE.
The patch also introduces the L_PGD_SWAPPER flag to mark pgd entries
pointing to pmd tables pre-allocated in the swapper_pg_dir and avoid
trying to free them at run-time. This flag is 0 with the classic page
table format.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
This patch introduces the pgtable-3level*.h files with definitions
specific to the LPAE page table format (3 levels of page tables).
Each table is 4KB and has 512 64-bit entries. An entry can point to a
40-bit physical address. The young, write and exec software bits share
the corresponding hardware bits (negated). Other software bits use spare
bits in the PTE.
The patch also changes some variable types from unsigned long or int to
pteval_t or pgprot_t.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Before we enable the MMU, we must ensure that the TTBR registers contain
sane values. After the MMU has been enabled, we jump to the *virtual*
address of the following function, so we also need to ensure that the
SCTLR write has taken effect.
This patch adds ISB instructions around the SCTLR write to ensure the
visibility of the above.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
This patch modifies the proc-v7.S file so that it only contains code
shared between classic MMU and LPAE. The non-common code is factored out
into a separate file.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
The FSR structure is different with LPAE and this patch moves the
classic MMU specific definition to a separate fsr-2level.c file that is
included in fault.c. It also moves the fsr_fs and FSR bits to the
fault.h file.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
The page table maintenance macros need to be duplicated between the
classic and the LPAE MMU so this patch moves those that are not common
to the pgtable-2level.h file.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Nick Piggin noted upon introducing 4level-fixup.h:
| Add a temporary "fallback" header so architectures can run with
| the 4level pagetables patch without modification. All architectures
| should be converted to use the folding headers (include/asm-generic/
| pgtable-nop?d.h) as soon as possible, and the fallback header removed.
This makes ARM compliant with this statement.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
With the arch/arm code conversion to pgtable-nopud.h, the section and
supersection (un|re)map code triggers compiler warnings on UP systems.
This is caused by pmd_offset() being given a pgd_t argument rather than
a pud_t one. This patch makes the necessary conversion with the
assumption that the pud is folded into the pgd. The page table setting
code only loops over the pmd which is enough with the classic page
tables. This code is not compiled when LPAE is enabled.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
ARM restart changes needed changes to common.h to make it local.
This conflicted with v3.2-rc4 DSS related hwmod changes that
git mergetool was not able to handle.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
