The GPIO Chip and GPIO IRQ Chip functionality are essentially orthogonal,
so GPIO IRQ Chip implementation shouldn't touch GPIO specific
registers and vise versa.
Hence, rework omap_gpio_irq_shutdown and try to touch only irqs specific
registers:
- don't configure GPIO as input (it, actually, should be already configured
as input).
- don't clear debounce configuration if GPIO is still used as GPIO.
We need to take in to account here commit c9c55d9211
("gpio/omap: fix off-mode bug: clear debounce settings on free/reset").
Also remove omap_reset_gpio() function as it is not used any more.
Signed-off-by: Grygorii Strashko <grygorii.strashko@linaro.org>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The GPIO bank will be kept powered in case if input parameters
are invalid or error occurred in omap_gpio_irq_type.
Hence, fix it by ensuring that GPIO bank will be unpowered
in case of errors and add additional check of value returned
from omap_set_gpio_triggering().
Signed-off-by: Grygorii Strashko <grygorii.strashko@linaro.org>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch fixes following issue:
- GPIOn is used as IRQ by some dev, for example PCF8575.INT -> gpio6.11
- PCFx driver knows nothing about type of IRQ line (GPIO or not)
so it doesn't request gpio and just do request_irq()
- If gpio6.11 will be exported through the sysfs and then un-xeported
then IRQs from PCFx will not be received any more, because
IRQ configuration for gpio6.11 will be cleaned up unconditionally
in omap_gpio_free.
Fix this by removing all GPIO IRQ specific code from omap_gpio_free()
and also do GPIO clean up (change direction to 'in' and disable debounce)
only if corresponding GPIO is not used as IRQ too.
GPIO IRQ will be properly cleaned up by GPIO irqchip code.
Signed-off-by: Grygorii Strashko <grygorii.strashko@linaro.org>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
If an interrupt controller doesn't support wake-up configuration,
irq_set_irq_wake() returns an error code. Then any subsequent call
trying to deconfigure wake-up will cause an imbalance, and a warning
will be printed:
WARNING: CPU: 1 PID: 1341 at kernel/irq/manage.c:540 irq_set_irq_wake+0x9c/0xf8()
Unbalanced IRQ 26 wake disable
To fix this, refrain from any further parent interrupt controller
(de)configuration if irq_set_irq_wake() failed.
Alternative fixes would be:
- calling "gic_set_irqchip_flags(IRQCHIP_SKIP_SET_WAKE)" from the
platform code,
- setting "gic_chip.flags = IRQCHIP_SKIP_SET_WAKE" in the GIC driver
code,
but these were withheld as the GIC hardware doesn't really support
wake-up interrupts.
Fixes: ab82fa7da4 ("gpio: rcar: Prevent module clock disable when wake-up is enabled")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
There have been concerns that the function names gpiod_set_array() and
gpiod_get_array() might be confusing to users. One might expect
gpiod_get_array() to return array values, while it is actually the array
counterpart of gpiod_get(). To be consistent with the single descriptor API
we could rename gpiod_set_array() to gpiod_set_array_value(). This makes
some function names a bit lengthy: gpiod_set_raw_array_value_cansleep().
Signed-off-by: Rojhalat Ibrahim <imr@rtschenk.de>
Acked-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Clean up chained handler and handler data if they were set by
gpiochip_set_chained_irqchip().
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The dln2 driver was initialising a gpiolib private field, which is now
gone.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch fixes an inverted return value of the gpio get_direction
function.
The wrong value causes the direction sysfs entry and GPIO debugfs file
to indicate incorrect GPIO direction settings. In some cases it also
prevents setting GPIO output values.
The problem is also present in all other stable kernel versions since
linux-3.12.
Cc: Stable <stable@vger.kernel.org> # v3.12+
Reported-by: Jochen Henneberg <jh@henneberg-systemdesign.com>
Signed-off-by: Michael Brunner <michael.brunner@kontron.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Make sure to free any hogged gpios on errors in gpiochip_add.
Also move all forward declarations to the top of the file.
Fixes: f625d46017 ("gpio: add GPIO hogging mechanism")
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Move irq trigger flags, which as sysfs-interface specific, to the class
device data.
This avoids accessing the gpio-descriptor flags field using non-atomic
operations without any locking, and allows for a more clear separation
of the sysfs interface from gpiolib core.
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Remove FLAG_SYSFS_DIR, which is sysfs-interface specific, and store it
in the class-device data instead.
Note that the flag is only used during export.
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Rename active-low helper using common prefix.
Also remove unnecessary manipulation of value argument.
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Make sure to deregister the class device (and release the irq) while
holding the sysfs lock in gpio_unexport to prevent racing with
gpio_export.
Note that this requires the recently introduced per-gpio locking to
avoid a deadlock with the kernfs active protection when waiting for the
attribute operations to drain during deregistration.
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add a per-gpio mutex to serialise attribute operations rather than use
one global mutex for all gpios and chips.
Having a single global lock for all gpios in a system adds unnecessary
latency to the sysfs interface, and especially when having gpio
controllers connected over slow buses.
Now that the global gpio-sysfs interrupt table is gone and with per-gpio
data in place, we can easily switch to using a more fine-grained locking
scheme.
Keep the global mutex to serialise the global (class) operations of gpio
export and unexport and chip removal.
Also document the locking assumptions made.
Note that this is also needed to fix a race between gpiod_export and
gpiod_unexport.
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Drop unnecessary locking from gpiod_export_link. If the class device has
not already been unregistered, class_find_device returns the ref-counted
class device so there's no need for locking.
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Only call irq helper if actually reconfiguring interrupt state.
This is a preparatory step in introducing separate gpio-irq request and
free functions.
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Store the value sysfs entry in the gpiod data rather than in a global
table accessed through an index stored in the overloaded gpio-descriptor
flag field.
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add gpiod class-device data.
This is a first step in getting rid of the insane gpio-descriptor flag
overloading, backward irq-interface implementation, and course grained
sysfs-interface locking (a single static mutex for every operation on
all exported gpios in a system).
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The attribute operations will never be called for an unregistered device
so remove redundant checks for FLAG_EXPORT.
Note that kernfs will also guarantee that any active sysfs operation has
finished before the attribute is removed during deregistration.
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Make sure to release any irq only after the class device has been
deregistered.
This avoids a race between gpiod_unexport and edge_store, where an irq
could be allocated just before the gpio class device is deregistered
without relying on FLAG_EXPORT and the global sysfs lock.
Note that there is no need to hold the sysfs lock when releasing the irq
after the class device is gone as kernfs will prevent further attribute
operations.
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use DEVICE_ATTR_RO and DEVICE_ATTR_RW rather than specifying masks and
callbacks directly.
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Remove gpiod_sysfs_set_active_low (and gpio_sysfs_set_active_low) which
allowed code to change the polarity of a gpio line even after it had
been exported through sysfs.
Drivers should not care, and generally does not know, about gpio-line
polarity which is a hardware feature that needs to be described by
firmware.
It is currently possible to define gpio-line polarity in device-tree and
acpi firmware or using platform data. Userspace can also change the
polarity through sysfs.
Note that drivers using the legacy gpio interface could still use
GPIOF_ACTIVE_LOW to change the polarity before exporting the gpio.
There are no in-kernel users of this interface.
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Harry Wei <harryxiyou@gmail.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: linux-doc@vger.kernel.org
Cc: linux-kernel@zh-kernel.org
Cc: linux-arch@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Rename the gpio-chip export/unexport functions to the more descriptive
names gpiochip_sysfs_register and gpiochip_sysfs_unregister.
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Clean gpio-chip class device registration and deregistration.
The class device is registered when a gpio-chip is added (or from
gpiolib_sysfs_init post-core init call), and deregistered when the chip
is removed.
Store the class device in struct gpio_chip directly rather than do a
class-device lookup on deregistration. This also removes the need for
the exported flag.
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reduce scope of sysfs_lock protection during chip export and unexport,
which is only needed to prevent gpiod (re-)exports during chip removal.
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Put the recently introduced gpio-chip pointer to some more use in
gpiod_export.
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Drivers should call gpiochip_lock_as_irq (which prevents the pin
direction from being changed) in their irq_request_resources callbacks
but some drivers currently fail to do so.
Instead a second, explicit and often redundant call to lock-as-irq is
made by the sysfs-interface implementation after an irq has been
requested.
Move the explicit call before the irq-request to match the unlock done
after the irq is later released. Note that this also fixes an irq leak,
should the explicit call ever have failed.
Also add a comment about removing the redundant call once the broken
drivers have been fixed.
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Clean up gpiochip_remove somewhat and only output warning about removing
chip with GPIOs requested once.
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
priv->irq is allocated using devm_kzalloc so there is no need to memset it.
Signed-off-by: Christophe Jaillet <christophe.jaillet@wanadoo.fr>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The platform_device_id is not modified by the driver and core uses it as
const.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This file is built off of a tristate Kconfig option and also contains
modular function calls so it should explicitly include module.h to
avoid compile breakage during header shuffles done in the future.
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: linux-gpio@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
ACPI specification knows two types of GPIOs: GpioIo and GpioInt. The latter
is used to describe that a given device interrupt line is connected to a
specific GPIO pin. Typical ACPI _CRS entry for such device looks like
below:
Name (_CRS, ResourceTemplate ()
{
I2cSerialBus (0x004A, ControllerInitiated, 0x00061A80,
AddressingMode7Bit, "\\_SB.PCI0.I2C6",
0x00, ResourceConsumer)
GpioIo (Exclusive, PullDefault, 0x0000, 0x0000,
IoRestrictionOutputOnly, "\\_SB.GPO0",
0x00, ResourceConsumer)
{
0x004B
}
GpioInt (Level, ActiveLow, Shared, PullDefault, 0x0000,
"\\_SB.GPO0", 0x00, ResourceConsumer)
{
0x004C
}
})
Currently drivers need to request a GPIO corresponding to the right GpioInt
and then translate that to Linux IRQ number. This adds unnecessary lines of
boiler-plate code.
We can ease this a bit by introducing acpi_dev_gpio_irq_get() analogous to
of_irq_get(). This function translates given GpioInt resource under the
device in question to the suitable Linux IRQ number.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
All supported iMX GPIO controllers store configured GPIO output value
in GPIO_DR data register, which is represented by GPIO generic reg_set.
Provide a BGPIOF_READ_OUTPUT_REG_SET flag to bgpio_init() to allow
correct getting of previously set output value.
Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Adding a BGPIOF_READ_OUTPUT_REG_SET initialization flag to GPIO
generic MMIO driver makes possible to remove a private get() value
function from the driver.
Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The change introduces BGPIOF_READ_OUTPUT_REG_SET flag for gpio-generic
GPIO chip implementation, which allows to get correct configured value
from reg_set register, input value is still get from reg_dat.
Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add GPIO controller driver for Netlogic XLP MIPS64 SOCs.
This driver is instantiated by device tree and supports interrupts
for GPIOs.
Signed-off-by: Kamlakant Patel <kamlakant.patel@broadcom.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The irq_domain_ops are not modified by the driver and the irqdomain core
code accepts pointer to a const data.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We currently get all kinds of errors building the omap gpio driver
as a module starting with:
undefined reference to `omap2_gpio_resume_after_idle'
undefined reference to `omap2_gpio_prepare_for_idle'
...
Let's fix the issue by adding inline functions to the header.
Note that we can now also remove the two unused functions for
omap_set_gpio_debounce and omap_set_gpio_debounce_time.
Then doing rmmod on the module produces further warnings
because of missing exit related functions. Let's add those.
And finally, we can make the Kconfig entry just a tristate
option that's selected for omaps.
Cc: Javier Martinez Canillas <javier@dowhile0.org>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@linaro.org>
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
At some point with all the GPIO clean-up we've broken the
MPUIO interrupts. Those are just a little bit different from
the GPIO interrupts, so we can fix it up just by setting
different irqchip functions for it. And then we can just
remove all old code trying to do the same.
Cc: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: Javier Martinez Canillas <javier@dowhile0.org>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@linaro.org>
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
MAX732X clears all pending interrupts on I2C read (when interrupts
register is being read). Driver doesn't need to send any ACKs when
interrupt was handled. So replace handle_edge_irq() with
handle_simple_irq().
Using handle_edge_irq() (w/o .irq_ack callback set) may lead to NULL
pointer dereference in some cases. E.g. this was observed on
hibernation process:
Unable to handle kernel NULL pointer dereference at virtual address 0
Backtrace:
(handle_edge_irq) from (resend_irqs)
(resend_irqs) from (tasklet_action)
(tasklet_action) from (__do_softirq)
(__do_softirq) from (run_ksoftirqd)
(run_ksoftirqd) from (smpboot_thread_fn)
(smpboot_thread_fn) from (kthread)
(kthread) from (ret_from_fork)
Signed-off-by: Semen Protsenko <semen.protsenko@globallogic.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
It's possible that multiple MAX732X can be hooked up to the same
interrupt line with the processor. So add IRQF_SHARED in requesting irq.
Signed-off-by: Semen Protsenko <semen.protsenko@globallogic.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Driver for the GPIO block found on NXP LPC18xx/43xx devices.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Set .irq_set_wake callback to prevent possible issues on wake-up.
This patch was inspired by this commit:
b80eef95be
Signed-off-by: Semen Protsenko <semen.protsenko@globallogic.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Unregister GPIOs requested through sysfs at chip remove to avoid leaking
the associated memory and sysfs entries.
The stale sysfs entries prevented the gpio numbers from being exported
when the gpio range was later reused (e.g. at device reconnect).
This also fixes the related module-reference leak.
Note that kernfs makes sure that any on-going sysfs operations finish
before the class devices are unregistered and that further accesses
fail.
The chip exported flag is used to prevent gpiod exports during removal.
This also makes it harder to trigger, but does not fix, the related race
between gpiochip_remove and export_store, which is really a race with
gpiod_request that needs to be addressed separately.
Also note that this would prevent the crashes (e.g. NULL-dereferences)
at reconnect that affects pre-3.18 kernels, as well as use-after-free on
operations on open attribute files on pre-3.14 kernels (prior to
kernfs).
Fixes: d8f388d8dc ("gpio: sysfs interface")
Cc: stable <stable@vger.kernel.org> # v2.6.27: 01cca93a94
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Implement gpio_chip's get_direction() callback, that lets other drivers get
particular GPIOs direction using gpiod_get_direction().
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Reviewed-by: Ray Jui <rjui@broadcom.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The signed error will be wrongly used as valid gpio offset
Reported-by: David Binderman <dcb314@hotmail.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Qipeng Zha <qipeng.zha@intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We've got a fairly large cleanup branch this time. The bulk of this is removal
of non-DT platforms of several flavors:
- Atmel at91 platforms go full-DT, with removal of remaining board-file based
support
- OMAP removes legacy board files for three more platforms
- Removal of non-DT mach-msm, newer Qualcomm platforms now live in mach-qcom
- Freescale i.MX25 also removes non-DT platform support
Most of the rest of the changes here are fallout from the above, i.e. for
example removal of drivers that now lack platforms, etc.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=BV8A
-----END PGP SIGNATURE-----
Merge tag 'armsoc-cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC cleanups from Olof Johansson:
"We've got a fairly large cleanup branch this time. The bulk of this
is removal of non-DT platforms of several flavors:
- Atmel at91 platforms go full-DT, with removal of remaining
board-file based support
- OMAP removes legacy board files for three more platforms
- removal of non-DT mach-msm, newer Qualcomm platforms now live in
mach-qcom
- Freescale i.MX25 also removes non-DT platform support"
Most of the rest of the changes here are fallout from the above, i.e. for
example removal of drivers that now lack platforms, etc.
* tag 'armsoc-cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (58 commits)
mmc: Remove msm_sdcc driver
gpio: Remove gpio-msm-v1 driver
ARM: Remove mach-msm and associated ARM architecture code
ARM: shmobile: cpuidle: Remove the pointless default driver
ARM: davinci: dm646x: Add interrupt resource for McASPs
ARM: davinci: irqs: Correct McASP1 TX interrupt definition for DM646x
ARM: davinci: dm646x: Clean up the McASP DMA resources
ARM: davinci: devices-da8xx: Add support for McASP2 on da830
ARM: davinci: devices-da8xx: Clean up and correct the McASP device creation
ARM: davinci: devices-da8xx: Add interrupt resource to McASP structs
ARM: davinci: devices-da8xx: Add resource name for the McASP DMA request
ARM: OMAP2+: Remove legacy support for omap3 TouchBook
ARM: OMAP3: Remove legacy support for devkit8000
ARM: OMAP3: Remove legacy support for EMA-Tech Stalker board
ARM: shmobile: Consolidate the pm code for R-Car Gen2
ARM: shmobile: r8a7791: Correct SYSCIER value
ARM: shmobile: r8a7790: Correct SYSCIER value
ARM: at91: remove old setup
ARM: at91: sama5d4: remove useless map_io
ARM: at91: sama5 use SoC detection infrastructure
...
cycle:
- A new GPIO hogging mechanism has been added. This can
be used on boards that want to drive some GPIO line high,
low, or set it as input on boot and then never touch it
again. For some embedded systems this is bliss and
simplifies things to a great extent.
- Some API cleanup and closure: gpiod_get_array() and
gpiod_put_array() has been added to get and put GPIOs
in bulk as was possible with the non-descriptor API.
- Encapsulate cross-calls to the pin control subsystem in
<linux/gpio/driver.h>. Now this should be the only header
any GPIO driver needs to include or something is wrong.
Cleanups restricting drivers to this include are welcomed
if tested.
- Sort the GPIO Kconfig and split it into submenus, as
it was becoming and unstructured, illogical and
unnavigatable mess. I hope this is easier to follow.
Menus that require a certain subsystem like I2C can
now be hidden nicely for example, still working on
others.
- New drivers:
- New driver for the Altera Soft GPIO.
- The F7188x driver now handles the F71869 and
F71869A variants.
- The MIPS Loongson driver has been moved to
drivers/gpio for consolidation and cleanup.
- Cleanups:
- The MAX732x is converted to use the GPIOLIB_IRQCHIP
infrastructure.
- The PCF857x is converted to use the GPIOLIB_IRQCHIP
infrastructure.
- Radical cleanup of the OMAP driver.
- Misc:
- Enable the DWAPB GPIO for all architectures. This is
a "hard IP" block from Synopsys which has started to
turn up in so diverse architectures as X86 Quark, ARC
and a slew of ARM systems. So even though it's not an
expander, it's generic enough to be available for all.
- We add a mock GPIO on Crystalcove PMIC after a long
discussion with Daniel Vetter et al, tracing back to
the shootout at the kernel summit where DRM drivers
and sub-componentization was discussed. In this case
a mock GPIO is assumed to be the best compromise
gaining some reuse of infrastructure without making
DRM drivers overly complex at the same time. Let's
see.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=QFbC
-----END PGP SIGNATURE-----
Merge tag 'gpio-v4.1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"This is the bulk of GPIO changes for the v4.1 development cycle:
- A new GPIO hogging mechanism has been added. This can be used on
boards that want to drive some GPIO line high, low, or set it as
input on boot and then never touch it again. For some embedded
systems this is bliss and simplifies things to a great extent.
- Some API cleanup and closure: gpiod_get_array() and
gpiod_put_array() has been added to get and put GPIOs in bulk as
was possible with the non-descriptor API.
- Encapsulate cross-calls to the pin control subsystem in
<linux/gpio/driver.h>. Now this should be the only header any GPIO
driver needs to include or something is wrong. Cleanups
restricting drivers to this include are welcomed if tested.
- Sort the GPIO Kconfig and split it into submenus, as it was
becoming and unstructured, illogical and unnavigatable mess. I
hope this is easier to follow. Menus that require a certain
subsystem like I2C can now be hidden nicely for example, still
working on others.
- New drivers:
- New driver for the Altera Soft GPIO.
- The F7188x driver now handles the F71869 and F71869A variants.
- The MIPS Loongson driver has been moved to drivers/gpio for
consolidation and cleanup.
- Cleanups:
- The MAX732x is converted to use the GPIOLIB_IRQCHIP
infrastructure.
- The PCF857x is converted to use the GPIOLIB_IRQCHIP
infrastructure.
- Radical cleanup of the OMAP driver.
- Misc:
- Enable the DWAPB GPIO for all architectures. This is a "hard
IP" block from Synopsys which has started to turn up in so
diverse architectures as X86 Quark, ARC and a slew of ARM
systems. So even though it's not an expander, it's generic
enough to be available for all.
- We add a mock GPIO on Crystalcove PMIC after a long discussion
with Daniel Vetter et al, tracing back to the shootout at the
kernel summit where DRM drivers and sub-componentization was
discussed. In this case a mock GPIO is assumed to be the best
compromise gaining some reuse of infrastructure without making
DRM drivers overly complex at the same time. Let's see"
* tag 'gpio-v4.1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (62 commits)
Revert "gpio: sch: use uapi/linux/pci_ids.h directly"
gpio: dwapb: remove dependencies
gpio: dwapb: enable for ARC
gpio: removing kfree remove functionality
gpio: mvebu: Fix mask/unmask managment per irq chip type
gpio: split GPIO drivers in submenus
gpio: move MFD GPIO drivers under their own comment
gpio: move BCM Kona Kconfig option
gpio: arrange SPI Kconfig symbols alphabetically
gpio: arrange PCI GPIO controllers alphabetically
gpio: arrange I2C Kconfig symbols alphabetically
gpio: arrange Kconfig symbols alphabetically
gpio: ich: Implement get_direction function
gpio: use (!foo) instead of (foo == NULL)
gpio: arizona: drop owner assignment from platform_drivers
gpio: max7300: remove 'ret' variable
gpio: use devm_kzalloc
gpio: sch: use uapi/linux/pci_ids.h directly
gpio: x-gene: fix devm_ioremap_resource() check
gpio: loongson: Add Loongson-3A/3B GPIO driver support
...
- Generic PM domains support update including new PM domain
callbacks to handle device initialization better (Russell King,
Rafael J Wysocki, Kevin Hilman).
- Unified device properties API update including a new mechanism
for accessing data provided by platform initialization code
(Rafael J Wysocki, Adrian Hunter).
- ARM cpuidle update including ARM32/ARM64 handling consolidation
(Daniel Lezcano).
- intel_idle update including support for the Silvermont Core in
the Baytrail SOC and for the Airmont Core in the Cherrytrail and
Braswell SOCs (Len Brown, Mathias Krause).
- New cpufreq driver for Hisilicon ACPU (Leo Yan).
- intel_pstate update including support for the Knights Landing
chip (Dasaratharaman Chandramouli, Kristen Carlson Accardi).
- QorIQ cpufreq driver update (Tang Yuantian, Arnd Bergmann).
- powernv cpufreq driver update (Shilpasri G Bhat).
- devfreq update including Tegra support changes (Tomeu Vizoso,
MyungJoo Ham, Chanwoo Choi).
- powercap RAPL (Running-Average Power Limit) driver update
including support for Intel Broadwell server chips (Jacob Pan,
Mathias Krause).
- ACPI device enumeration update related to the handling of the
special PRP0001 device ID allowing DT-style 'compatible' property
to be used for ACPI device identification (Rafael J Wysocki).
- ACPI EC driver update including limited _DEP support (Lan Tianyu,
Lv Zheng).
- ACPI backlight driver update including a new mechanism to allow
native backlight handling to be forced on non-Windows 8 systems
and a new quirk for Lenovo Ideapad Z570 (Aaron Lu, Hans de Goede).
- New Windows Vista compatibility quirk for Sony VGN-SR19XN (Chen Yu).
- Assorted ACPI fixes and cleanups (Aaron Lu, Martin Kepplinger,
Masanari Iida, Mika Westerberg, Nan Li, Rafael J Wysocki).
- Fixes related to suspend-to-idle for the iTCO watchdog driver and
the ACPI core system suspend/resume code (Rafael J Wysocki, Chen Yu).
- PM tracing support for the suspend phase of system suspend/resume
transitions (Zhonghui Fu).
- Configurable delay for the system suspend/resume testing facility
(Brian Norris).
- PNP subsystem cleanups (Peter Huewe, Rafael J Wysocki).
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=erd3
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-4.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management and ACPI updates from Rafael Wysocki:
"These are mostly fixes and cleanups all over, although there are a few
items that sort of fall into the new feature category.
First off, we have new callbacks for PM domains that should help us to
handle some issues related to device initialization in a better way.
There also is some consolidation in the unified device properties API
area allowing us to use that inferface for accessing data coming from
platform initialization code in addition to firmware-provided data.
We have some new device/CPU IDs in a few drivers, support for new
chips and a new cpufreq driver too.
Specifics:
- Generic PM domains support update including new PM domain callbacks
to handle device initialization better (Russell King, Rafael J
Wysocki, Kevin Hilman)
- Unified device properties API update including a new mechanism for
accessing data provided by platform initialization code (Rafael J
Wysocki, Adrian Hunter)
- ARM cpuidle update including ARM32/ARM64 handling consolidation
(Daniel Lezcano)
- intel_idle update including support for the Silvermont Core in the
Baytrail SOC and for the Airmont Core in the Cherrytrail and
Braswell SOCs (Len Brown, Mathias Krause)
- New cpufreq driver for Hisilicon ACPU (Leo Yan)
- intel_pstate update including support for the Knights Landing chip
(Dasaratharaman Chandramouli, Kristen Carlson Accardi)
- QorIQ cpufreq driver update (Tang Yuantian, Arnd Bergmann)
- powernv cpufreq driver update (Shilpasri G Bhat)
- devfreq update including Tegra support changes (Tomeu Vizoso,
MyungJoo Ham, Chanwoo Choi)
- powercap RAPL (Running-Average Power Limit) driver update including
support for Intel Broadwell server chips (Jacob Pan, Mathias Krause)
- ACPI device enumeration update related to the handling of the
special PRP0001 device ID allowing DT-style 'compatible' property
to be used for ACPI device identification (Rafael J Wysocki)
- ACPI EC driver update including limited _DEP support (Lan Tianyu,
Lv Zheng)
- ACPI backlight driver update including a new mechanism to allow
native backlight handling to be forced on non-Windows 8 systems and
a new quirk for Lenovo Ideapad Z570 (Aaron Lu, Hans de Goede)
- New Windows Vista compatibility quirk for Sony VGN-SR19XN (Chen Yu)
- Assorted ACPI fixes and cleanups (Aaron Lu, Martin Kepplinger,
Masanari Iida, Mika Westerberg, Nan Li, Rafael J Wysocki)
- Fixes related to suspend-to-idle for the iTCO watchdog driver and
the ACPI core system suspend/resume code (Rafael J Wysocki, Chen Yu)
- PM tracing support for the suspend phase of system suspend/resume
transitions (Zhonghui Fu)
- Configurable delay for the system suspend/resume testing facility
(Brian Norris)
- PNP subsystem cleanups (Peter Huewe, Rafael J Wysocki)"
* tag 'pm+acpi-4.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (74 commits)
ACPI / scan: Fix NULL pointer dereference in acpi_companion_match()
ACPI / scan: Rework modalias creation when "compatible" is present
intel_idle: mark cpu id array as __initconst
powercap / RAPL: mark rapl_ids array as __initconst
powercap / RAPL: add ID for Broadwell server
intel_pstate: Knights Landing support
intel_pstate: remove MSR test
cpufreq: fix qoriq uniprocessor build
ACPI / scan: Take the PRP0001 position in the list of IDs into account
ACPI / scan: Simplify acpi_match_device()
ACPI / scan: Generalize of_compatible matching
device property: Introduce firmware node type for platform data
device property: Make it possible to use secondary firmware nodes
PM / watchdog: iTCO: stop watchdog during system suspend
cpufreq: hisilicon: add acpu driver
ACPI / EC: Call acpi_walk_dep_device_list() after installing EC opregion handler
cpufreq: powernv: Report cpu frequency throttling
intel_idle: Add support for the Airmont Core in the Cherrytrail and Braswell SOCs
intel_idle: Update support for Silvermont Core in Baytrail SOC
PM / devfreq: tegra: Register governor on module init
...
* device-properties:
device property: Introduce firmware node type for platform data
device property: Make it possible to use secondary firmware nodes
driver core: Implement device property accessors through fwnode ones
driver core: property: Update fwnode_property_read_string_array()
driver core: Add comments about returning array counts
ACPI: Introduce has_acpi_companion()
driver core / ACPI: Represent ACPI companions using fwnode_handle
The Synopsys DesignWare DWAPB GPIO block is popular to
synthesize amongst many architectures: X86, ARM, ARC.
The driver was restricted to only these archs due to
using [read|write]l_relaxed() accessors that were not
universally available in the past,
but as of commit 9439eb3ab9
"asm-generic: io: implement relaxed accessor macros as
conditional wrappers" these accessors are available on all
archs so this should not be a problem any more. Enable the
driver for all archs.
Cc: Alexey Brodkin <Alexey.Brodkin@synopsys.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Synopsys SDP platform uses DW GPIO controller in design with
ARC cores. So adding ARC to architectures that may select this
GPIO controller.
Even though support for Synopsys SDP is yet to be submitted we'll need
this tiny option enabled at least for properly working interrupts (DW
GPIO controller is used as interrupt controller).
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
commit 3de07e5aaf290a0b58919 ("drivers: gpio: use devm_kzalloc")
introduce devm_kzalloc() for allocating the memory. In this case kfree
is not required to use. Above commit id introduced the bug that kfree
is not removed from the remove function.
This patch fix the above bug.
Signed-off-by: Varka Bhadram <varkab@cdac.in>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Level IRQ handlers and edge IRQ handler are managed by tow different
sets of registers. But currently the driver uses the same mask for the
both registers. It lead to issues with the following scenario:
First, an IRQ is requested on a GPIO to be triggered on front. After,
this an other IRQ is requested for a GPIO of the same bank but
triggered on level. Then the first one will be also setup to be
triggered on level. It leads to an interrupt storm.
The different kind of handler are already associated with two
different irq chip type. With this patch the driver uses a private
mask for each one which solves this issue.
It has been tested on an Armada XP based board and on an Armada 375
board. For the both boards, with this patch is applied, there is no
such interrupt storm when running the previous scenario.
This bug was already fixed but in a different way in the legacy
version of this driver by Evgeniy Dushistov:
9ece8839b1 "ARM: orion: Fix for certain
sequence of request_irq can cause irq storm". The fact the new version
of the gpio drive could be affected had been discussed there:
http://thread.gmane.org/gmane.linux.ports.arm.kernel/344670/focus=364012
Reported-by: Evgeniy A. Dushistov <dushistov@mail.ru>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Cc: <stable@vger.kernel.org> # v3.7 +
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Create Kconfig submenus for memory mapped, I2C, MFD,
PCI, SPI and USB GPIO drivers to help navigate the forest
of drivers in this subsystem. The I2C, SPI and USB menus
get dependencies so we don't have to see them unless we
have the required subsystem enabled in the first place.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Get rid of AC97, MODULbus and other weird subheadings for
GPIO drivers. Move all MFD drivers out of I2C etc and in under
the MFD comment. This is too weird as it is and makes no
sense, if the dependent parent driver is MFD, group these as
MFD GPIO drivers. Alphabetize and move this comment group
inbetween "I2C" and "PCI" to also have the groups in
alphabetic order.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Move the Kconfig option for the Broadcom BCM Kona up to the
commin GPIO controllers, as it is currently grouped under
MODULbus expanders which it definately is not.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Rearrange the SPI GPIO expanders in alphabetic order
as already indicated by the comment in the file.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Rearrange PCI GPIO controllers in alphabetic order
as already indicated by the comment in the file.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Rearrange the I2C GPIO expanders in alphabetic order
as already indicated by the comment in the file.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This rearranges the GPIO drivers Kconfig symbols alphabetically
as the top comment in the file already states they should be.
No functional changes whatsoever.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Allow the kernel to query the driver for a GPIO's pin direction.
Signed-off-by: Aaron Sierra <asierra@xes-inc.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This driver no need to set the owner field, it will be populated
by driver core.
Signed-off-by: Varka Bhadram <varkab@cdac.in>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We can use devres API for allocating memory. No need of using kfree.
Signed-off-by: Varka Bhadram <varkab@cdac.in>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Header moved from linux/pci_ids.h to uapi/linux/pci_ids.h,
use the new header directly so we can drop
the wrapper in include/linux/pci_ids.h.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
devm_ioremap_resource() returns IOMEM_ERR_PTR() and it never
returns NULL, fix the check to prevent access to invalid
virtual address.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This driver is orphaned now that mach-msm has been removed.
Delete it.
Cc: David Brown <davidb@codeaurora.org>
Cc: Bryan Huntsman <bryanh@codeaurora.org>
Cc: Daniel Walker <dwalker@fifo99.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Alexandre Courbot <gnurou@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Kumar Gala <galak@codeaurora.org>
Even if bus is not hot-pluggable, the devices can be unbound from the
driver via sysfs, so we should not be using __exit annotations on
remove() methods. The only exception is drivers registered with
platform_driver_probe() which specifically disables sysfs bind/unbind
attributes.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Now GPIO syscon driver produces bunch of warnings during the
boot of Kesytone 2 SoCs:
gpio-syscon soc:keystone_dsp_gpio@02620240: can't read the dir register offset!
gpio-syscon soc:keystone_dsp_gpio@2620244: can't read the dir register offset!
This message unintentionally was added using dev_err(), but its
actual log level is debug, because third cell of "ti,syscon-dev" is
optional.
Hence change it to dev_dbg() as it should be.
This patch fixes commit:
5a3e3f8 ("gpio: syscon: retriave syscon node and regs offsets from dt")
Reported-by: Russell King <linux@arm.linux.org.uk>
Tested-by: Murali Karicheri <m-karicheri2@ti.com>
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Signed-off-by: Grygorii Strashko <grygorii.strashko@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Convert GPIO IRQ functions to use GPIO offset instead of system
GPIO numbers. This allows to drop unneeded conversations between
system GPIO <-> GPIO offset which are done in many places and
many times.
It is safe to do now because:
- gpiolib always passes GPIO offset to GPIO controller
- OMAP GPIO driver converted to use IRQ domain, so
struct irq_data->hwirq contains GPIO offset
This is preparation step before removing:
#define GPIO_INDEX(bank, gpio)
#define GPIO_BIT(bank, gpio)
int omap_irq_to_gpio()
Tested-by: Tony Lindgren <tony@atomide.com>
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Acked-by: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: Grygorii Strashko <grygorii.strashko@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The 'gpio' parameter isn't needed any more as it
duplicates 'offset' parameter, so drop it.
Tested-by: Tony Lindgren <tony@atomide.com>
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Acked-by: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: Grygorii Strashko <grygorii.strashko@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Convert debounce functions to use GPIO offset instead of system
GPIO numbers. This allows to drop unneeded conversations between
system GPIO <-> GPIO offset which are done in many places and
many times.
It is safe to do now because:
- gpiolib always passes GPIO offset to GPIO controller
- OMAP GPIO driver converted to use IRQ domain
This is preparation step before removing:
#define GPIO_INDEX(bank, gpio)
#define GPIO_BIT(bank, gpio)
int omap_irq_to_gpio()
Tested-by: Tony Lindgren <tony@atomide.com>
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Acked-by: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: Grygorii Strashko <grygorii.strashko@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Both functions omap_set_gpio_dataout_reg() and
omap_set_gpio_dataout_mask() accept GPIO offset
as 'gpio' input parameter, so rename it to 'offset' and
drop usage of GPIO_BIT() macro.
Tested-by: Tony Lindgren <tony@atomide.com>
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Acked-by: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: Grygorii Strashko <grygorii.strashko@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Convert omap_gpio_is_input() to use GPIO offset instead of mask and,
in such way, make code simpler and remove few lines of code.
Tested-by: Tony Lindgren <tony@atomide.com>
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Acked-by: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: Grygorii Strashko <grygorii.strashko@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
All systems using the TC3589x multifunction expander uses
devicetree, so don't clutter the place with a lot of
and assume it is there.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
When the GPIO module is needed for wake-up, it's module clock must not
be disabled. Hence implement irq_chip.irq_set_wake(), which
increments/decrements the clock's enable_count when needed, and forwards
the wake-up state to the upstream interrupt controller.
This fixes wake-up from s2ram using gpio-keys when using a PM Domain to
manage the module clock.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The existing variable gpio_chip already points to the gpiochip instance,
hence use it everywhere.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Intel Quark SoC contains the DW GPIO on board. While fixing the build error
the commit 1972c97db5 (gpio: dwapb: fix compile errors) disables the
possibility to build the driver on X86, i.e. Intel Quark.
The patch reenables it for Intel Quark as well.
Since we have Intel Quark SoC introduced in 4.0-rc1 I would like to make this
fix available there as well, though the actual MFD driver [1] is applied only
for next version.
[1] https://lkml.org/lkml/2015/2/1/217
Fixes: 1972c97db5 (gpio: dwapb: fix compile errors)
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In acpi_gpiochip_request_interrupts() the handle local
variable already contains the value that we want to pass
to acpi_walk_resources(), so it is better to use that
variable instead of evaluating ACPI_HANDLE() once more
for the same device.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
If dev is NULL in __gpiod_get_index() and both ACPI and OF are
enabled, it will be checked twice before the code decides to give
up with DT/ACPI lookup, so avoid that.
Also use the observation that ACPI_COMPANION() is much more efficient
than ACPI_HANDLE(), because the latter uses the former and carries out
a check and a pointer dereference on top of it, so replace the
ACPI_HANDLE() check with an ACPI_COMPANION() one which does not
require the additional IS_ENABLED(CONFIG_ACPI) check too.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Hanjun Guo <hanjun.guo@linaro.org>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
If GPIO driver use pin mapping, need to translate pin number
between ACPI table and GPIO driver.
This issue is found on one platform with Cherryview gpio
controller, kernel is hang when executed _PS0 method of
one ACPI device, since without this translation, it access
invalid gpiodesc array.
Verified it works again with this patch.
Signed-off-by: qipeng.zha <qipeng.zha@intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add support for the GPIOs found on the Fintek SuperI/O chip F71869A,
such as the one found on the Jetway JNF99-525 motherboard, to the f7188x
gpio driver.
Signed-off-by: Andreas Bofjall <andreas@gazonk.org>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add support for the GPIOs found on the Fintek SuperI/O chip F71869, such
as the one found on the Jetway NF96u-525 motherboard, to the f7188x gpio
driver.
Signed-off-by: Andreas Bofjall <andreas@gazonk.org>
Tested-by: Les Schaffer <schaffer@optonline.net>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The company is called "Fintek", not "Fintech". Fix it.
Signed-off-by: Andreas Bofjall <andreas@gazonk.org>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Commit 1feb57a245
"gpio: add parameter to allow the use named gpios"
includes a double-consted array. What we want is not
const const * but const * const (const pointer to const
data). Fix this.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: Olliver Schinagl <oliver@schinagl.nl>
Cc: Rojhalat Ibrahim <imr@rtschenk.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Now that we have struct fwnode_handle, we can use that to point to
ACPI companions from struct device objects instead of pointing to
struct acpi_device directly.
There are two benefits from that. First, the somewhat ugly and
hackish struct acpi_dev_node can be dropped and, second, the same
struct fwnode_handle pointer can be used in the future to point
to other (non-ACPI) firmware device node types.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Grant Likely <grant.likely@linaro.org>
The macro BANK_OFF which calculates the base offset for each GPIO port.
The macro is needlessly complex and unreadable. Simplify the
calculation to a simple math operation.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: linux-gpio@vger.kernel.org
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Adds a new driver for Altera soft GPIO IP. The driver is able to do
read/write and allows GPIO to be a interrupt controller.
Tested on Altera GHRD on interrupt handling and IO.
v10:
- Updated conflicting device tree parameters
- Removed unused headers
- Used macro instead of magic numbers for ngpio
- Code readability cleanup using ?: and temporal variables
- Removed leftover garbage and unnecessary function calls
- Checked bgpio_init but unusable because Altera GPIO may not
be a multiple of 8 bits
v9:
- Removed duplicated initialization on set_type using temporals
to improve code readability in calling generic_handle_irq
- Using ?: ternary to reduce code size
v8:
- Using for_each_set_bit
- Added const for struct definition
- Removed naggy pr_err
- Sort alpha header
- Remove unused macros
- Use fixed width data types instead of unsigned long
- Whitespace issue fixes
- Removed _relaxed function for better compatibility across different
CPU
- Changed irq_create_mapping to platform_get_irq updated implementation
to use gpiochip_irqchip_add
- Reserve interrupt-cells number 2 in device tree binding for future
use
- Remove confusing sections on devicetree bindings
- Added tristate Kconfig help text
v7:
- Used dev_warn instead of pr_warn
- Clean up unnecesarry if else indentation
v6:
- Added irq_startup and irq_shutdown
- Changed bitwise clamping style
- Cleanup bitwise operation to improve readability change naming of
mapped irqs from virq to mapped_irq
v5:
- Dispose irq_domain mapping correctly
- Update optional binding description in binding docs
v4:
- Added vendor prefix to devicetree binding for IP specific properties
using MMIO GPIO helper library instead of manually map PIO to memory
- altera_gpio_chip inline struct documentation to kerneldoc
- Using dev_ print to print a better failure message
v2, v3:
- Do not reference NO_IRQ
- Updated irq_set_type to only allow the hardware configured irq type
Signed-off-by: Tien Hock Loh <thloh@altera.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Since commit 98686d9a52 ("gpio: mpc8xxx: Convert to platform device
interface"), we get the following section mismatch warning. Remove the
__initdata annotation to fix it.
WARNING: vmlinux.o(.data+0xbc28): Section mismatch in reference from the variable mpc8xxx_plat_driver to the variable .init.data:mpc8xxx_gpio_ids
The variable mpc8xxx_plat_driver references
the variable __initdata mpc8xxx_gpio_ids
If the reference is valid then annotate the
variable with __init* or __refdata (see linux/init.h) or name the variable:
*_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add device managed variants of gpiod_get_array() / gpiod_put_array()
functions for conveniently obtaining and disposing of an entire array
of GPIOs with one function call.
Signed-off-by: Rojhalat Ibrahim <imr@rtschenk.de>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Introduce new functions for conveniently obtaining and disposing of
an entire array of GPIOs with one function call.
ACPI parts tested by Mika Westerberg, DT parts tested by Rojhalat
Ibrahim.
Change log:
v5: move the ACPI functions to gpiolib-acpi.c
v4: - use shorter names for members of struct gpio_descs
- rename lut_gpio_count to platform_gpio_count for clarity
- add check for successful memory allocation
- use ERR_CAST()
v3: - rebase on current linux-gpio devel branch
- fix ACPI GPIO counting
- allow for zero-sized arrays
- make the flags argument mandatory for the new functions
- clarify documentation
v2: change interface
Suggested-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Rojhalat Ibrahim <imr@rtschenk.de>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Tested-by: Rojhalat Ibrahim <imr@rtschenk.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Avoid multiple identical definitions of the gpio suffix strings by putting
them into a global constant array.
Signed-off-by: Rojhalat Ibrahim <imr@rtschenk.de>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The gpio binding document says that new code should always use named
gpios. Patch 40b73183 added support to parse a list of gpios from child
nodes, but does not make it possible to use named gpios. This patch adds
the con_id property and implements it is done in gpiolib.c, where the
old-style of using unnamed gpios still works.
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
Acked-by: Bryan Wu <cooloney@gmail.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The pcf857x GPIO and interrupt controller uses dummy_irq_chip, which
does not implement irq_chip.irq_set_wake() and does not set
IRQCHIP_SKIP_SET_WAKE.
This causes two s2ram issues if wake-up is enabled for the pcf857x GPIO
pins:
1. During resume from s2ram, the following warning is printed:
WARNING: CPU: 0 PID: 1046 at kernel/irq/manage.c:537 irq_set_irq_wake+0x9c/0xf8()
Unbalanced IRQ 113 wake disable
2. Wake-up through the pcf857x GPIO pins may fail, as the parent
interrupt controller may be suspended.
Migrate the pcf857x GPIO and interrupt controller from dummy_irq_chip to
its own irq_chip. This irq chip implements irq_chip.irq_set_wake() to
propagate its wake-up setting to the parent interrupt controller.
This fixes wake-up through gpio-keys on sh73a0/kzm9g, where the pcf857x
interrupt is cascaded to irq-renesas-intc-irqpin, and the latter must
not be suspended when wake-up is enabled.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Switch the PCF857x GPIO driver to use the gpiolib irqchip helpers.
This driver uses a nested threaded interrupt, hence handle_nested_irq()
and gpiochip_set_chained_irqchip() must be used.
Note that this removes the checks added in commit 21fd3cd187
("gpio: pcf857x: call the gpio user handler iff gpio_to_irq is done"),
as the interrupt mappings are no longer created on-demand by the driver,
but by gpiochip_irqchip_add() during initialization.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Based on Boris Brezillion's work this is a reworked patch
of his initial GPIO hogging mechanism.
This patch provides a way to initially configure specific GPIO
when the GPIO controller is probed.
The actual DT scanning to collect the GPIO specific data is performed
as part of gpiochip_add().
The purpose of this is to allow specific GPIOs to be configured
without any driver specific code.
This is particularly useful because board design are getting
increasingly complex and given SoC pins can now have more
than 10 mux values, a lot of connections are now dependent on
external IO muxes to switch various modes.
Specific drivers should not necessarily need to be aware of
what accounts to a specific board implementation. This board level
"description" should be best kept as part of the dts file.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Take a sweep to bring the irq support for the MAX732x expanders
into the gpiolib core to cut down on duplicated code.
Only compile tested! I need some feedback from people using this
expander with interrupts to tell me if things go right or
wrong when I do this.
Cc: Semen Protsenko <semen.protsenko@globallogic.com>
Cc: Mans Rullgard <mans@mansr.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The gpio_chip operations receive a pointer the gpio_chip struct which is
contained in the driver's private struct, yet the container_of call in those
functions point to the mfd struct defined in include/linux/mfd/tps65912.h.
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: Nicolas Saenz Julienne <nicolassaenzj@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The change:
7b8792bbdf
gpiolib: of: Correct error handling in of_get_named_gpiod_flags
assumed that only one gpio-chip is registred per of-node.
Some drivers register more than one chip per of-node, so
adjust the matching function of_gpiochip_find_and_xlate to
not stop looking for chips if a node-match is found and
the translation fails.
Cc: Stable <stable@vger.kernel.org>
Fixes: 7b8792bbdf ("gpiolib: of: Correct error handling in of_get_named_gpiod_flags")
Signed-off-by: Hans Holmberg <hans.holmberg@intel.com>
Acked-by: Alexandre Courbot <acourbot@nvidia.com>
Tested-by: Robert Jarzmik <robert.jarzmik@free.fr>
Tested-by: Tyler Hall <tylerwhall@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Pull ARM updates from Russell King:
- clang assembly fixes from Ard
- optimisations and cleanups for Aurora L2 cache support
- efficient L2 cache support for secure monitor API on Exynos SoCs
- debug menu cleanup from Daniel Thompson to allow better behaviour for
multiplatform kernels
- StrongARM SA11x0 conversion to irq domains, and pxa_timer
- kprobes updates for older ARM CPUs
- move probes support out of arch/arm/kernel to arch/arm/probes
- add inline asm support for the rbit (reverse bits) instruction
- provide an ARM mode secondary CPU entry point (for Qualcomm CPUs)
- remove the unused ARMv3 user access code
- add driver_override support to AMBA Primecell bus
* 'for-linus' of git://ftp.arm.linux.org.uk/~rmk/linux-arm: (55 commits)
ARM: 8256/1: driver coamba: add device binding path 'driver_override'
ARM: 8301/1: qcom: Use secondary_startup_arm()
ARM: 8302/1: Add a secondary_startup that assumes ARM mode
ARM: 8300/1: teach __asmeq that r11 == fp and r12 == ip
ARM: kprobes: Fix compilation error caused by superfluous '*'
ARM: 8297/1: cache-l2x0: optimize aurora range operations
ARM: 8296/1: cache-l2x0: clean up aurora cache handling
ARM: 8284/1: sa1100: clear RCSR_SMR on resume
ARM: 8283/1: sa1100: collie: clear PWER register on machine init
ARM: 8282/1: sa1100: use handle_domain_irq
ARM: 8281/1: sa1100: move GPIO-related IRQ code to gpio driver
ARM: 8280/1: sa1100: switch to irq_domain_add_simple()
ARM: 8279/1: sa1100: merge both GPIO irqdomains
ARM: 8278/1: sa1100: split irq handling for low GPIOs
ARM: 8291/1: replace magic number with PAGE_SHIFT macro in fixup_pv code
ARM: 8290/1: decompressor: fix a wrong comment
ARM: 8286/1: mm: Fix dma_contiguous_reserve comment
ARM: 8248/1: pm: remove outdated comment
ARM: 8274/1: Fix DEBUG_LL for multi-platform kernels (without PL01X)
ARM: 8273/1: Seperate DEBUG_UART_PHYS from DEBUG_LL on EP93XX
...
- GPIOLIB core changes:
- Create and use of_mm_gpiochip_remove() for removing
memory-mapped OF GPIO chips
- GPIO MMIO library suppports bgpio_set_multiple for
switching several lines at once, a feature merged in
the last cycle.
- New drivers:
- New driver for the APM X-gene standby GPIO controller
- New driver for the Fujitsu MB86S7x GPIO controller
- Cleanups:
- Moved rcar driver to use gpiolib irqchip
- Moxart converted to the GPIO MMIO library
- GE driver converted to GPIO MMIO library
- Move sx150x to irqdomain
- Move max732x to irqdomain
- Move vx855 to use managed resources
- Move dwapb to use managed resources
- Clean tc3589x from platform data
- Clean stmpe driver to use device tree only probe
- New subtypes:
- sx1506 support in the sx150x driver
- Quark 1000 SoC support in the SCH driver
- Support X86 in the Xilinx driver
- Support PXA1928 in the PXA driver
- Extended drivers:
- max732x supports device tree probe
- sx150x supports device tree probe
- Various minor cleanups and bug fixes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=yWrB
-----END PGP SIGNATURE-----
Merge tag 'gpio-v3.20-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO changes from Linus Walleij:
"This is the GPIO bulk changes for the v3.20 series:
GPIOLIB core changes:
- Create and use of_mm_gpiochip_remove() for removing memory-mapped
OF GPIO chips
- GPIO MMIO library suppports bgpio_set_multiple for switching
several lines at once, a feature merged in the last cycle.
New drivers:
- New driver for the APM X-gene standby GPIO controller
- New driver for the Fujitsu MB86S7x GPIO controller
Cleanups:
- Moved rcar driver to use gpiolib irqchip
- Moxart converted to the GPIO MMIO library
- GE driver converted to GPIO MMIO library
- Move sx150x to irqdomain
- Move max732x to irqdomain
- Move vx855 to use managed resources
- Move dwapb to use managed resources
- Clean tc3589x from platform data
- Clean stmpe driver to use device tree only probe
New subtypes:
- sx1506 support in the sx150x driver
- Quark 1000 SoC support in the SCH driver
- Support X86 in the Xilinx driver
- Support PXA1928 in the PXA driver
Extended drivers:
- max732x supports device tree probe
- sx150x supports device tree probe
Various minor cleanups and bug fixes"
* tag 'gpio-v3.20-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (61 commits)
gpio: kconfig: replace PPC_OF with PPC
gpio: pxa: add PXA1928 gpio type support
dt/bindings: gpio: add compatible string for marvell,pxa1928-gpio
gpio: pxa: remove mach IRQ includes
gpio: max732x: use an inline function for container cast
gpio: use sizeof() instead of hardcoded values
gpio: max732x: add set_multiple function
gpio: sch: Consolidate similar algorithms
gpio: tz1090-pdc: Use resource_size to fix off-by-one resource size calculation
gpio: ge: Convert to use devm_kstrdup
gpio: correctly use const char * const
gpio: sx150x: fixup OF support
gpio: mpc8xxx: Use of_mm_gpiochip_remove
gpio: Add Fujitsu MB86S7x GPIO driver
gpio: mpc8xxx: Convert to platform device interface.
gpio: zevio: Use of_mm_gpiochip_remove
gpio: gpio-mm-lantiq: Use of_mm_gpiochip_remove
gpio: gpio-mm-lantiq: Use of_property_read_u32
gpio: gpio-mm-lantiq: Do not replicate code
gpio :gpio-mm-lantiq: Use devm_kzalloc
...
The PPC_OF is a ppc specific option which is used to mean that the
firmware device tree access functions are available. Since all the
ppc platforms have a device tree, it is aways set to 'y' for ppc.
So it makes no sense to keep a such option in the current kernel.
Replace it with PPC.
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add support for PXA1928 GPIOs. The PXA1928 adds a 6th bank from previous
generations.
Signed-off-by: Jing Xiang <jxiang@marvell.com>
Signed-off-by: Xiangzhan Meng <mengxzh@marvell.com>
[robh: ported to 3.19 from vendor kernel]
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Alexandre Courbot <gnurou@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In preparation to enable ARCH_MMP on ARM64, the include of mach/irqs.h
must be eliminated. mach/irqs.h was being included for IRQ_GPIO{0,1},
but these IRQs are always passed in as resources now. We can use irq0
and irq1 and get rid of IRQ_GPIOx. Get rid of the ifdef in the process
as it is no longer needed.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Alexandre Courbot <gnurou@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Cast the struct gpio_chip into a max732x_chip using an inline
macro and move the assignment to the variable declaration
to save lines and simplify things.
Cc: Semen Protsenko <semen.protsenko@globallogic.com>
Acked-by: Mans Rullgard <mans@mansr.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
gpiolib uses a fixed string for the suffixes and defines it at 32 bytes.
Later in the code snprintf is used with this fixed value of 32. Using
sizeof() is safer in case the size for the suffixes is ever changed.
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds a set_multiple function to the MAX732x GPIO driver,
allowing for performance gains when using gpiod_set_array().
Signed-off-by: Mans Rullgard <mans@mansr.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Fix memory leak in the gpio sysfs interface due to failure to drop
reference to device returned by class_find_device when setting the
gpio-line polarity.
Fixes: 0769746183 ("gpiolib: add support for changing value polarity
in sysfs")
Cc: stable <stable@vger.kernel.org> # v2.6.33
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Fix memory leak in the gpio sysfs interface due to failure to drop
reference to device returned by class_find_device when creating a link.
Fixes: a4177ee7f1 ("gpiolib: allow exported GPIO nodes to be named
using sysfs links")
Cc: stable <stable@vger.kernel.org> # v2.6.32
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
As a part of driver consolidation, move GPIO-related IRQ code to
drivers/gpio/gpio-sa1100.c. The code does not use GPIOLIB_IRQCHIP (yet),
because sa1100 does not have a device for gpios, which is a requirement
for GPIOLIB_IRQCHIP. This will be the next step.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Low GPIO pins use an interrupt in SC interrupts space. However it's
possible to handle them as if all the GPIO interrupts are instead tied
to single GPIO handler, which later decodes GEDR register and
chain-calls next IRQ handler. So split first 11 interrupts into system
part (IRQ_GPIO0_SC - IRQ_GPIO10_SC) which work exactly like the rest of
system controller interrupts and real GPIO interrupts
(IRQ_GPIO0..IRQ_GPIO10). A single handler sa1100_gpio_handler then
decodes and calls next handler.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Consolidating similar algorithms into common functions to make
GPIO SCH simpler and manageable.
Signed-off-by: Chang Rebecca Swee Fun <rebecca.swee.fun.chang@intel.com>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use devm_kstrdup to simplify the error handling path.
Also return -ENOMEM instead of 0 if devm_kstrdup fails.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
On my previous patch I was overly hasty and made the suffixes string
array
const char const *suffixes, instaed of const char * const suffixes. This
patch corrects that
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Create default gpio base if neither device node nor
platform data is defined.
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Tested-by: Antonio Fiol <antonio@fiol.es>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Similar to omap_gpio_irq_type() let's make sure that the GPIO
is usable as an interrupt if the platform init code did not
call gpio_request(). Otherwise we can get invalid device access
after setup_irq():
WARNING: CPU: 0 PID: 1 at drivers/bus/omap_l3_noc.c:147 l3_interrupt_handler+0x214/0x340()
44000000.ocp:L3 Custom Error: MASTER MPU TARGET L4CFG (Idle): Data Access in Supervisor mode during Functional access
...
[<c05f21e4>] (__irq_svc) from [<c05f1974>] (_raw_spin_unlock_irqrestore+0x34/0x44)
[<c05f1974>] (_raw_spin_unlock_irqrestore) from [<c00914a8>] (__setup_irq+0x244/0x530)
[<c00914a8>] (__setup_irq) from [<c00917d4>] (setup_irq+0x40/0x8c)
[<c00917d4>] (setup_irq) from [<c0039c8c>] (omap_system_dma_probe+0x1d4/0x2b4)
[<c0039c8c>] (omap_system_dma_probe) from [<c03b2200>] (platform_drv_probe+0x44/0xa4)
...
We can fix this the same way omap_gpio_irq_type() is handling it.
Note that the long term solution is to change the gpio-omap driver
to handle the banks as separate driver instances. This will allow
us to rely on just runtime PM for tracking the bank specific state.
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Javier Martinez Canillas <javier@dowhile0.org>
Cc: Kevin Hilman <khilman@kernel.org>
Cc: Santosh Shilimkar <ssantosh@kernel.org>
Tested-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Make OF conditional on CONFIG_OF_GPIO, rename and register
the match table.
Reported-by: Mike Krinkin <krinkin.m.u@gmail.com>
Cc: Wei Chen <Wei.Chen@csr.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Since d621e8bae5 (Create of_mm_gpiochip_remove), there is a
counterpart for of_mm_gpiochip_add.
This patch implements the remove function of the driver making use of
it.
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Driver for Fujitsu MB86S7x SoCs that have a memory mapped GPIO controller.
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Signed-off-by: Andy Green <andy.green@linaro.org>
Signed-off-by: Vincent Yang <Vincent.Yang@tw.fujitsu.com>
Signed-off-by: Tetsuya Nuriya <nuriya.tetsuya@jp.fujitsu.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This way we do not need to transverse the device tree manually.
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: devicetree@vger.kernel.org
Acked-by: Peter Korsgaard <peter@korsgaard.com>
Acked-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Since d621e8bae5 (Create of_mm_gpiochip_remove), there is a
counterpart for of_mm_gpiochip_add.
This patch implements the remove function of the driver making use of
it.
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: Fabian Vogt <fabian@ritter-vogt.de>
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Since d621e8bae5 (Create of_mm_gpiochip_remove), there is a
counterpart for of_mm_gpiochip_add.
This patch implements the remove function of the driver making use of
it.
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: John Crispin <blogic@openwrt.org>
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Instead of parsing manually the shadow content, use the much simpler
helper of_property_read_u32.
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: John Crispin <blogic@openwrt.org>
Cc: devicetree@vger.kernel.org
Cc: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Since d621e8bae5 (Create of_mm_gpiochip_remove), there is a
counterpart for of_mm_gpiochip_add.
This patch implements the remove function of the driver making use of
it.
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Require that device tree be used with STMPE (all platforms use this)
and enforce OF_GPIO, then delete the platform data.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Driver for standby GPIO controller of APM X-Gene SoCs on arm64.
Signed-off-by: Y Vo <yvo@apm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Current sx150x gpio expander driver doesn't support
DTS. Now we added dts support for this driver.
Signed-off-by: Wei Chen <Wei.Chen@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add set_multiple functions to the generic driver for memory-mapped GPIO
controllers to improve performance when setting multiple outputs
simultaneously.
Signed-off-by: Rojhalat Ibrahim <imr@rtschenk.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Commit ffe4770b9b ("gpio-amd8111: check ioport_map return value")
adds the error check on ioport_map(). It doesnt release the requested region.
On failure this patch release the region that has requested before.
Signed-off-by: Varka Bhadram <varkab@cdac.in>
Reported-by: Alexandre Courbot <gnurou@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Include linux/slab.h to fix following compilation error.
drivers/gpio/gpio-ge.c: In function ‘gef_gpio_probe’:
drivers/gpio/gpio-ge.c:95:2: error: implicit declaration of function ‘kfree’ [-Werror=implicit-function-declaration]
kfree(bgc->gc.label);
Signed-off-by: Kamlakant Patel <kamlakant.patel@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
that have been around forever in the GPIO subsystem, most of them
also tagged for stable:
- A large slew of fixes from Johan Hovold who is finally testing and
reviewing the removal path of the GPIO drivers.
- Fix of_get_named_gpiod_flags() so it works as expected.
- Fix an IRQ handling bug in the crystalcove driver.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=ekXq
-----END PGP SIGNATURE-----
Merge tag 'gpio-v3.19-4' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO fixes from Linus Walleij:
"Here is a set of fixes that mainly appeared when Johan Hovold started
exercising the removal path of the GPIO library, dealing with
hotplugging of GPIO controllers. Details from tag:
A slew of fixes dealing with some irritating bugs (non-regressions)
that have been around forever in the GPIO subsystem, most of them also
tagged for stable:
- A large slew of fixes from Johan Hovold who is finally testing and
reviewing the removal path of the GPIO drivers.
- Fix of_get_named_gpiod_flags() so it works as expected.
- Fix an IRQ handling bug in the crystalcove driver"
* tag 'gpio-v3.19-4' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
gpiolib: of: Correct error handling in of_get_named_gpiod_flags
gpio: sysfs: fix gpio attribute-creation race
gpio: sysfs: fix gpio device-attribute leak
gpio: sysfs: fix gpio-chip device-attribute leak
gpio: unregister gpiochip device before removing it
gpio: fix sleep-while-atomic in gpiochip_remove
gpio: fix memory leak and sleep-while-atomic
gpio: clean up gpiochip_add error handling
gpio: fix gpio-chip list corruption
gpio: fix memory and reference leaks in gpiochip_add error path
gpio: crystalcove: use handle_nested_irq
of_get_named_gpiod_flags fails with -EPROBE_DEFER in cases
where the gpio chip is available and the GPIO translation fails.
This causes drivers to be re-probed erroneusly, and hides the
real problem(i.e. the GPIO number being out of range).
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: Hans Holmberg <hans.holmberg@intel.com>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Fix the coding style issue by adding a blank line after declaration
Signed-off-by: Mohammad Jamal <md.jamalmohiuddin@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
X86 Kconfig symbol is X86, not ARCH_X86.
Fixes: c586b3075d5b47d8 (gpio/xilinx: Add support for X86 Arch)
Reported-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Switch the R-Car Gen2 GPIO driver to use the gpiolib irqchip helpers.
While doing this also make sure that gpiochip_irqchip_add() is called
after the gpiochip itself is registered, as required.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
If the call to devm_kzalloc() fails, nothing must be cleant up.
This was missed before because gpio_rcar_probe() had a "return"
statement after the first "goto err0".
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Fixes: df0c6c8023 ("gpio: rcar: Add minimal runtime PM support")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Ensure that when there is an error during probe that the gpiochip is
removed and the generic irq chip is removed.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Wrap some long lines.
Prefer seq_puts() over seq_printf().
space to tab conversions.
Spelling error fix.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Checkpatch complains, and probably with good reason that we should use
const char const * for the static constant array that never gets
changed.
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
ioport_map() may fail. Its safe to check the return value.
Signed-off-by: Varka Bhadram <varkab@cdac.in>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use resource managed APIs to simplify the code a bit.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use resource_size to fix off-by-one resource size calculation
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This platform_driver does not need to set an owner, it will be populated by the
driver core.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
"gc->ngpio" is a number between 1 and GRGPIO_MAX_NGPIO. If "offset" is
GRGPIO_MAX_NGPIO then we're going one step beyond the end of the
priv->lirqs[] array.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This device is only used from the device tree, and the startup()
and remove() callbacks are not used anywhere in the kernel, so
retire them and the pdata altogether.
Cc: Samuel Ortiz <sameo@linux.intel.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use devm_* APIs to simplify the code a bit.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use the newly created of_mm_gpiochip_remove function for cleaning up
of_mm_gpiochip_add
Suggested-by: Alexandre Courbot <gnurou@gmail.com>
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Create counterpart of of_mm_gpiochip_add(). This way the modules that
can be removable do not duplicate the cleanup code.
Suggested-by: Alexandre Courbot <gnurou@gmail.com>
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Currently, we had two gpio chips on cores configured as dual.
This lead to mapping the same memory region twice and duplicating the
init and remove code.
This patch creates a single gpiochip for single and dual cores.
Suggested-by: Alexandre Courbot <gnurou@gmail.com>
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Some documentation were not following the kernel-doc format.
Backporting patch from Xilinx git repository.
Suggested-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Core can be accessed via PCIe on X86 platform.
This patch also allows the driver to be used as module.
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This way we do not need to transverse the device tree manually and we
support hot plugged devices.
Also Implement remove callback so the driver can be unloaded
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Instead of calculating the register offset per call, pre-calculate it on
probe time.
Acked-by: Alexandre Courbot <acourbot@nvidia.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Intel Quark X1000 provides a total of 16 GPIOs. The GPIOs are split between
the legacy I/O bridge and the GPIO controller.
GPIO-SCH is the GPIO pins on legacy bridge for Intel Quark SoC.
Intel Quark X1000 has 2 GPIOs powered by the core power well and 6 from
the suspend power well.
This piece of work is derived from Dan O'Donovan's initial work for Quark
X1000 enabling.
Signed-off-by: Chang Rebecca Swee Fun <rebecca.swee.fun.chang@intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
semtech has two series of sx150x gpio expanders: sx150x-456 and
sx150x-789.
The current gpio-150x driver in linux only support sx1508 and
sx1509.
We added sx1506 support code into this driver.
Signed-off-by: Wei Chen <Wei.Chen@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The sx150x gpio driver used a loop to set liner irq map for gpio pins.
Now we use the irq domain to rebuild this irq mappig and make sure the
codes are still compatible to old users.
this patch also adds IRQF_ONESHOT flag to fix the IRQ flooding issues.
Signed-off-by: Wei Chen <Wei.Chen@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
[Make Kconfig select GPIOLIB_IRQCHIP]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Fix attribute-creation race with userspace by using the default group
to create also the contingent gpio device attributes.
Fixes: d8f388d8dc ("gpio: sysfs interface")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The gpio device attributes were never destroyed when the gpio was
unexported (or on export failures).
Use device_create_with_groups() to create the default device attributes
of the gpio class device. Note that this also fixes the
attribute-creation race with userspace for these attributes.
Remove contingent attributes in export error path and on unexport.
Fixes: d8f388d8dc ("gpio: sysfs interface")
Cc: stable <stable@vger.kernel.org> # v2.6.27+
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The gpio-chip device attributes were never destroyed when the device was
removed.
Fix by using device_create_with_groups() to create the device attributes
of the chip class device.
Note that this also fixes the attribute-creation race with userspace.
Fixes: d8f388d8dc ("gpio: sysfs interface")
Cc: stable <stable@vger.kernel.org> # v2.6.27+
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Unregister gpiochip device (used to export information through sysfs)
before removing it internally. This way removal will reverse addition.
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Move direct and indirect calls to gpiochip_remove_pin_ranges outside of
spin lock as they can end up taking a mutex in pinctrl_remove_gpio_range.
Note that the pin ranges are already added outside of the lock.
Fixes: 9ef0d6f762 ("gpiolib: call pin removal in chip removal function")
Fixes: f23f1516b6 ("gpiolib: provide provision to register pin ranges")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Fix memory leak and sleep-while-atomic in gpiochip_remove.
The memory leak was introduced by afa82fab5e ("gpio / ACPI: Move event
handling registration to gpiolib irqchip helpers") that moved the
release of acpi interrupt resources to gpiochip_irqchip_remove, but by
then the resources are no longer accessible as the acpi_gpio_chip has
already been freed by acpi_gpiochip_remove.
Note that this also fixes a few potential sleep-while-atomics, which has
been around since 1425052097 ("gpio: add IRQ chip helpers in gpiolib")
when the call to gpiochip_irqchip_remove while holding a spinlock was
added (a couple of irq-domain paths can end up grabbing mutexes).
Fixes: afa82fab5e ("gpio / ACPI: Move event handling registration to
gpiolib irqchip helpers")
Fixes: 1425052097 ("gpio: add IRQ chip helpers in gpiolib")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Fix potential corruption of gpio-chip list due to failure to remove the
chip from the list before returning in gpiochip_add error path.
The chip could be long gone when the global list is next traversed,
something which could lead to a null-pointer dereference. In the best
case (chip not deallocated) we are just leaking the gpio range.
Fixes: 14e85c0e69 ("gpio: remove gpio_descs global array")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Memory allocated and references taken by of_gpiochip_add and
acpi_gpiochip_add were never released on errors in gpiochip_add (e.g.
failure to find free gpio range).
Fixes: 391c970c0d ("of/gpio: add default of_xlate function if device
has a node pointer")
Fixes: 664e3e5ac6 ("gpio / ACPI: register to ACPI events
automatically")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use the irq_chip bus_sync_unlock method to update hardware registers
instead of scheduling work from the mask/unmask methods. This simplifies
a bit the driver and make it more uniform with the other GPIO IRQ
drivers.
Signed-off-by: Octavian Purdila <octavian.purdila@intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
irqmap is optional property, so priv->domain can be NULL if !irqmap.
Thus add NULL test for priv->domain before calling irq_domain_remove()
to prevent NULL pointer dereference.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
dln2_gpio_direction_output() ignored the state passed into it. Fix it.
Also make dln2_gpio_pin_set_out_val return int, so we can check the error value.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Tested-by: Daniel Baluta <daniel.baluta@intel.com>
Acked-by: Alexandre Courbot <acourbot@nvidia.com>
Reviewed-by: Octavian Purdila <octavian.purdila@intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
As noticed during suspend/resume operations, the IRQ can be unmasked
then disabled in suspend and eventually enabled in resume, but without
being unmasked.
The current implementation does not take into account interactions
between mask/unmask and enable/disable interrupts, and thus in the
above scenarios the IRQs remain unactive.
To fix this we removed the enable/disable operations as they fallback
to mask/unmask anyway.
We also remove the pending bitmaks as it is already done in irq_data
(i.e. IRQS_PENDING).
Signed-off-by: Octavian Purdila <octavian.purdila@intel.com>
Acked-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes, just
removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There are
some ath9k patches coming in through this tree that have been acked by
the wireless maintainers as they relied on the debugfs changes.
Everything has been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlSOD20ACgkQMUfUDdst+ylLPACg2QrW1oHhdTMT9WI8jihlHVRM
53kAoLeteByQ3iVwWurwwseRPiWa8+MI
=OVRS
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core update from Greg KH:
"Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes,
just removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There
are some ath9k patches coming in through this tree that have been
acked by the wireless maintainers as they relied on the debugfs
changes.
Everything has been in linux-next for a while"
* tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (324 commits)
Revert "ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries"
fs: debugfs: add forward declaration for struct device type
firmware class: Deletion of an unnecessary check before the function call "vunmap"
firmware loader: fix hung task warning dump
devcoredump: provide a one-way disable function
device: Add dev_<level>_once variants
ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries
ath: use seq_file api for ath9k debugfs files
debugfs: add helper function to create device related seq_file
drivers/base: cacheinfo: remove noisy error boot message
Revert "core: platform: add warning if driver has no owner"
drivers: base: support cpu cache information interface to userspace via sysfs
drivers: base: add cpu_device_create to support per-cpu devices
topology: replace custom attribute macros with standard DEVICE_ATTR*
cpumask: factor out show_cpumap into separate helper function
driver core: Fix unbalanced device reference in drivers_probe
driver core: fix race with userland in device_add()
sysfs/kernfs: make read requests on pre-alloc files use the buffer.
sysfs/kernfs: allow attributes to request write buffer be pre-allocated.
fs: sysfs: return EGBIG on write if offset is larger than file size
...
- A new API that allows setting more than one GPIO at the
time. This is implemented for the new descriptor-based
API only and makes it possible to e.g. toggle a clock and
data line at the same time, if the hardware can do this
with a single register write. Both consumers and drivers
need new calls, and the core will fall back to driving
individual lines where needed. Implemented for the MPC8xxx
driver initially.
- Patched the mdio-mux-gpio and the serial mctrl driver
that drives modems to use the new multiple-setting API
to set several signals simultaneously.
- Get rid of the global GPIO descriptor array, and instead
allocate descriptors dynamically for each GPIO on a certain
GPIO chip. This moves us closer to getting rid of the
limitation of using the global, static GPIO numberspace.
- New driver and device tree bindings for 74xx ICs.
- New driver and device tree bindings for the VF610 Vybrid.
- Support the RCAR r8a7793 and r8a7794.
- Guidelines for GPIO device tree bindings trying to get
things a bit more strict with the advent of combined
device properties.
- Suspend/resume support for the MVEBU driver.
- A slew of minor fixes and improvements.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=ZAhA
-----END PGP SIGNATURE-----
Merge tag 'gpio-v3.19-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull take two of the GPIO updates:
"Same stuff as last time, now with a fixup patch for the previous
compile error plus I ran a few extra rounds of compile-testing.
This is the bulk of GPIO changes for the v3.19 series:
- A new API that allows setting more than one GPIO at the time. This
is implemented for the new descriptor-based API only and makes it
possible to e.g. toggle a clock and data line at the same time, if
the hardware can do this with a single register write. Both
consumers and drivers need new calls, and the core will fall back
to driving individual lines where needed. Implemented for the
MPC8xxx driver initially
- Patched the mdio-mux-gpio and the serial mctrl driver that drives
modems to use the new multiple-setting API to set several signals
simultaneously
- Get rid of the global GPIO descriptor array, and instead allocate
descriptors dynamically for each GPIO on a certain GPIO chip. This
moves us closer to getting rid of the limitation of using the
global, static GPIO numberspace
- New driver and device tree bindings for 74xx ICs
- New driver and device tree bindings for the VF610 Vybrid
- Support the RCAR r8a7793 and r8a7794
- Guidelines for GPIO device tree bindings trying to get things a bit
more strict with the advent of combined device properties
- Suspend/resume support for the MVEBU driver
- A slew of minor fixes and improvements"
* tag 'gpio-v3.19-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (33 commits)
gpio: mcp23s08: fix up compilation error
gpio: pl061: document gpio-ranges property for bindings file
gpio: pl061: hook request if gpio-ranges avaiable
gpio: mcp23s08: Add option to configure IRQ output polarity as active high
gpio: fix deferred probe detection for legacy API
serial: mctrl_gpio: use gpiod_set_array function
mdio-mux-gpio: Use GPIO descriptor interface and new gpiod_set_array function
gpio: remove const modifier from gpiod_get_direction()
gpio: remove gpio_descs global array
gpio: mxs: implement get_direction callback
gpio: em: Use dynamic allocation of GPIOs
gpio: Check if base is positive before calling gpio_is_valid()
gpio: mcp23s08: Add simple IRQ support for SPI devices
gpio: mcp23s08: request a shared interrupt
gpio: mcp23s08: Do not free unrequested interrupt
gpio: rcar: Add r8a7793 and r8a7794 support
gpio-mpc8xxx: add mpc8xxx_gpio_set_multiple function
gpiolib: allow simultaneous setting of multiple GPIO outputs
gpio: mvebu: add suspend/resume support
gpio: gpio-davinci: remove duplicate check on resource
..
The driver depends on the chip.of_node being present to compile,
which is the case on some target platforms but not others.
Instead, rely on chip.dev->of_node to be used, as struct device
always has an of_node in place.
Cc: Alexander Stein <alexander.stein@systec-electronic.com>
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
- Force conversion of the ux500 pin control device trees
and parsers to use the generic pin control bindings.
- New driver and device tree bindings for the Qualcomm
PMIC MPP pin controller and GPIO.
- Some ACPI infrastructure for pin controllers.
- New driver for the Intel CherryView/Braswell pin controller,
the first Intel pin controller to fully take advantage of
the pin control subsystem.
- Support the Freescale i.MX VF610 variant.
- Support the sunxi A80 variant.
- Support the Samsung Exynos 4415 and Exynos 7 variants.
- Split out Intel pin controllers to their own subdirectory.
- A large slew of rockchip pin control updates, including
suspend/resume support.
- A large slew of Samsung Exynos pin controller updates.
- Various minor updates and fixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=sxpe
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v3.19-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control changes from Linus Walleij:
"Here is a stash of pin control changes I have collected for the v3.19
series. Mainly new hardware support, with Intels new embedded SoC as
the especially interesting thing standing out, fully using the
subsystem.
- Force conversion of the ux500 pin control device trees and parsers
to use the generic pin control bindings.
- New driver and device tree bindings for the Qualcomm PMIC MPP pin
controller and GPIO.
- Some ACPI infrastructure for pin controllers.
- New driver for the Intel CherryView/Braswell pin controller, the
first Intel pin controller to fully take advantage of the pin
control subsystem.
- Support the Freescale i.MX VF610 variant.
- Support the sunxi A80 variant.
- Support the Samsung Exynos 4415 and Exynos 7 variants.
- Split out Intel pin controllers to their own subdirectory.
- A large slew of rockchip pin control updates, including
suspend/resume support.
- A large slew of Samsung Exynos pin controller updates.
- Various minor updates and fixes"
* tag 'pinctrl-v3.19-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (49 commits)
pinctrl: at91: enhance (debugfs) at91_gpio_dbg_show
pinctrl: meson: add device tree bindings documentation
gpio: tz1090: Fix error handling of irq_of_parse_and_map
pinctrl: tz1090-pinctrl.txt: Fix typo in binding
pinctrl: pinconf-generic: Declare dt_params/conf_items const
pinctrl: exynos: Add support for Exynos4415
pinctrl: exynos: Add initial driver data for Exynos7
pinctrl: exynos: Add irq_chip instance for Exynos7 wakeup interrupts
pinctrl: exynos: Consolidate irq domain callbacks
pinctrl: exynos: Generalize the eint16_31 demux code
pinctrl: samsung: Separate per-bank init and runtime data
pinctrl: samsung: Constify samsung_pin_ctrl struct
pinctrl: samsung: Constify samsung_pin_bank_type struct
pinctrl: samsung: Drop unused label field in samsung_pin_ctrl struct
pinctrl: samsung: Make samsung_pinctrl_get_soc_data use ERR_PTR()
pinctrl: Add Intel Cherryview/Braswell pin controller support
gpio / ACPI: Add knowledge about pin controllers to acpi_get_gpiod()
pinctrl: Fix path error in documentation
pinctrl: rockchip: save and restore gpio6_c6 pinmux in suspend/resume
pinctrl: rockchip: add suspend/resume functions
...
This time we have some more new material than we used to have during
the last couple of development cycles.
The most important part of it to me is the introduction of a unified
interface for accessing device properties provided by platform
firmware. It works with Device Trees and ACPI in a uniform way and
drivers using it need not worry about where the properties come
from as long as the platform firmware (either DT or ACPI) makes
them available. It covers both devices and "bare" device node
objects without struct device representation as that turns out to
be necessary in some cases. This has been in the works for quite
a few months (and development cycles) and has been approved by
all of the relevant maintainers.
On top of that, some drivers are switched over to the new interface
(at25, leds-gpio, gpio_keys_polled) and some additional changes are
made to the core GPIO subsystem to allow device drivers to manipulate
GPIOs in the "canonical" way on platforms that provide GPIO information
in their ACPI tables, but don't assign names to GPIO lines (in which
case the driver needs to do that on the basis of what it knows about
the device in question). That also has been approved by the GPIO
core maintainers and the rfkill driver is now going to use it.
Second is support for hardware P-states in the intel_pstate driver.
It uses CPUID to detect whether or not the feature is supported by
the processor in which case it will be enabled by default. However,
it can be disabled entirely from the kernel command line if necessary.
Next is support for a platform firmware interface based on ACPI
operation regions used by the PMIC (Power Management Integrated
Circuit) chips on the Intel Baytrail-T and Baytrail-T-CR platforms.
That interface is used for manipulating power resources and for
thermal management: sensor temperature reporting, trip point setting
and so on.
Also the ACPI core is now going to support the _DEP configuration
information in a limited way. Basically, _DEP it supposed to reflect
off-the-hierarchy dependencies between devices which may be very
indirect, like when AML for one device accesses locations in an
operation region handled by another device's driver (usually, the
device depended on this way is a serial bus or GPIO controller).
The support added this time is sufficient to make the ACPI battery
driver work on Asus T100A, but it is general enough to be able to
cover some other use cases in the future.
Finally, we have a new cpufreq driver for the Loongson1B processor.
In addition to the above, there are fixes and cleanups all over the
place as usual and a traditional ACPICA update to a recent upstream
release.
As far as the fixes go, the ACPI LPSS (Low-power Subsystem) driver
for Intel platforms should be able to handle power management of
the DMA engine correctly, the cpufreq-dt driver should interact
with the thermal subsystem in a better way and the ACPI backlight
driver should handle some more corner cases, among other things.
On top of the ACPICA update there are fixes for race conditions
in the ACPICA's interrupt handling code which might lead to some
random and strange looking failures on some systems.
In the cleanups department the most visible part is the series
of commits targeted at getting rid of the CONFIG_PM_RUNTIME
configuration option. That was triggered by a discussion
regarding the generic power domains code during which we realized
that trying to support certain combinations of PM config options
was painful and not really worth it, because nobody would use them
in production anyway. For this reason, we decided to make
CONFIG_PM_SLEEP select CONFIG_PM_RUNTIME and that lead to the
conclusion that the latter became redundant and CONFIG_PM could
be used instead of it. The material here makes that replacement
in a major part of the tree, but there will be at least one more
batch of that in the second part of the merge window.
Specifics:
- Support for retrieving device properties information from ACPI
_DSD device configuration objects and a unified device properties
interface for device drivers (and subsystems) on top of that.
As stated above, this works with Device Trees and ACPI and allows
device drivers to be written in a platform firmware (DT or ACPI)
agnostic way. The at25, leds-gpio and gpio_keys_polled drivers
are now going to use this new interface and the GPIO subsystem
is additionally modified to allow device drivers to assign names
to GPIO resources returned by ACPI _CRS objects (in case _DSD is
not present or does not provide the expected data). The changes
in this set are mostly from Mika Westerberg, Rafael J Wysocki,
Aaron Lu, and Darren Hart with some fixes from others (Fabio Estevam,
Geert Uytterhoeven).
- Support for Hardware Managed Performance States (HWP) as described
in Volume 3, section 14.4, of the Intel SDM in the intel_pstate
driver. CPUID is used to detect whether or not the feature is
supported by the processor. If supported, it will be enabled
automatically unless the intel_pstate=no_hwp switch is present in
the kernel command line. From Dirk Brandewie.
- New Intel Broadwell-H ID for intel_pstate (Dirk Brandewie).
- Support for firmware interface based on ACPI operation regions
used by the PMIC chips on the Intel Baytrail-T and Baytrail-T-CR
platforms for power resource control and thermal management
(Aaron Lu).
- Limited support for retrieving off-the-hierarchy dependencies
between devices from ACPI _DEP device configuration objects
and deferred probing support for the ACPI battery driver based
on the _DEP information to make that driver work on Asus T100A
(Lan Tianyu).
- New cpufreq driver for the Loongson1B processor (Kelvin Cheung).
- ACPICA update to upstream revision 20141107 which only affects
tools (Bob Moore).
- Fixes for race conditions in the ACPICA's interrupt handling
code and in the ACPI code related to system suspend and resume
(Lv Zheng and Rafael J Wysocki).
- ACPI core fix for an RCU-related issue in the ioremap() regions
management code that slowed down significantly after CPUs had
been allowed to enter idle states even if they'd had RCU callbakcs
queued and triggered some problems in certain proprietary graphics
driver (and elsewhere). The fix replaces synchronize_rcu() in
that code with synchronize_rcu_expedited() which makes the issue
go away. From Konstantin Khlebnikov.
- ACPI LPSS (Low-Power Subsystem) driver fix to handle power
management of the DMA engine included into the LPSS correctly.
The problem is that the DMA engine doesn't have ACPI PM support
of its own and it simply is turned off when the last LPSS device
having ACPI PM support goes into D3cold. To work around that,
the PM domain used by the ACPI LPSS driver is redesigned so at
least one device with ACPI PM support will be on as long as the
DMA engine is in use. From Andy Shevchenko.
- ACPI backlight driver fix to avoid using it on "Win8-compatible"
systems where it doesn't work and where it was used by default by
mistake (Aaron Lu).
- Assorted minor ACPI core fixes and cleanups from Tomasz Nowicki,
Sudeep Holla, Huang Rui, Hanjun Guo, Fabian Frederick, and
Ashwin Chaugule (mostly related to the upcoming ARM64 support).
- Intel RAPL (Running Average Power Limit) power capping driver
fixes and improvements including new processor IDs (Jacob Pan).
- Generic power domains modification to power up domains after
attaching devices to them to meet the expectations of device
drivers and bus types assuming devices to be accessible at
probe time (Ulf Hansson).
- Preliminary support for controlling device clocks from the
generic power domains core code and modifications of the
ARM/shmobile platform to use that feature (Ulf Hansson).
- Assorted minor fixes and cleanups of the generic power
domains core code (Ulf Hansson, Geert Uytterhoeven).
- Assorted minor fixes and cleanups of the device clocks control
code in the PM core (Geert Uytterhoeven, Grygorii Strashko).
- Consolidation of device power management Kconfig options by making
CONFIG_PM_SLEEP select CONFIG_PM_RUNTIME and removing the latter
which is now redundant (Rafael J Wysocki and Kevin Hilman). That
is the first batch of the changes needed for this purpose.
- Core device runtime power management support code cleanup related
to the execution of callbacks (Andrzej Hajda).
- cpuidle ARM support improvements (Lorenzo Pieralisi).
- cpuidle cleanup related to the CPUIDLE_FLAG_TIME_VALID flag and
a new MAINTAINERS entry for ARM Exynos cpuidle (Daniel Lezcano and
Bartlomiej Zolnierkiewicz).
- New cpufreq driver callback (->ready) to be executed when the
cpufreq core is ready to use a given policy object and cpufreq-dt
driver modification to use that callback for cooling device
registration (Viresh Kumar).
- cpufreq core fixes and cleanups (Viresh Kumar, Vince Hsu,
James Geboski, Tomeu Vizoso).
- Assorted fixes and cleanups in the cpufreq-pcc, intel_pstate,
cpufreq-dt, pxa2xx cpufreq drivers (Lenny Szubowicz, Ethan Zhao,
Stefan Wahren, Petr Cvek).
- OPP (Operating Performance Points) framework modification to
allow OPPs to be removed too and update of a few cpufreq drivers
(cpufreq-dt, exynos5440, imx6q, cpufreq) to remove OPPs (added
during initialization) on driver removal (Viresh Kumar).
- Hibernation core fixes and cleanups (Tina Ruchandani and
Markus Elfring).
- PM Kconfig fix related to CPU power management (Pankaj Dubey).
- cpupower tool fix (Prarit Bhargava).
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=5dox
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management updates from Rafael Wysocki:
"This time we have some more new material than we used to have during
the last couple of development cycles.
The most important part of it to me is the introduction of a unified
interface for accessing device properties provided by platform
firmware. It works with Device Trees and ACPI in a uniform way and
drivers using it need not worry about where the properties come from
as long as the platform firmware (either DT or ACPI) makes them
available. It covers both devices and "bare" device node objects
without struct device representation as that turns out to be necessary
in some cases. This has been in the works for quite a few months (and
development cycles) and has been approved by all of the relevant
maintainers.
On top of that, some drivers are switched over to the new interface
(at25, leds-gpio, gpio_keys_polled) and some additional changes are
made to the core GPIO subsystem to allow device drivers to manipulate
GPIOs in the "canonical" way on platforms that provide GPIO
information in their ACPI tables, but don't assign names to GPIO lines
(in which case the driver needs to do that on the basis of what it
knows about the device in question). That also has been approved by
the GPIO core maintainers and the rfkill driver is now going to use
it.
Second is support for hardware P-states in the intel_pstate driver.
It uses CPUID to detect whether or not the feature is supported by the
processor in which case it will be enabled by default. However, it
can be disabled entirely from the kernel command line if necessary.
Next is support for a platform firmware interface based on ACPI
operation regions used by the PMIC (Power Management Integrated
Circuit) chips on the Intel Baytrail-T and Baytrail-T-CR platforms.
That interface is used for manipulating power resources and for
thermal management: sensor temperature reporting, trip point setting
and so on.
Also the ACPI core is now going to support the _DEP configuration
information in a limited way. Basically, _DEP it supposed to reflect
off-the-hierarchy dependencies between devices which may be very
indirect, like when AML for one device accesses locations in an
operation region handled by another device's driver (usually, the
device depended on this way is a serial bus or GPIO controller). The
support added this time is sufficient to make the ACPI battery driver
work on Asus T100A, but it is general enough to be able to cover some
other use cases in the future.
Finally, we have a new cpufreq driver for the Loongson1B processor.
In addition to the above, there are fixes and cleanups all over the
place as usual and a traditional ACPICA update to a recent upstream
release.
As far as the fixes go, the ACPI LPSS (Low-power Subsystem) driver for
Intel platforms should be able to handle power management of the DMA
engine correctly, the cpufreq-dt driver should interact with the
thermal subsystem in a better way and the ACPI backlight driver should
handle some more corner cases, among other things.
On top of the ACPICA update there are fixes for race conditions in the
ACPICA's interrupt handling code which might lead to some random and
strange looking failures on some systems.
In the cleanups department the most visible part is the series of
commits targeted at getting rid of the CONFIG_PM_RUNTIME configuration
option. That was triggered by a discussion regarding the generic
power domains code during which we realized that trying to support
certain combinations of PM config options was painful and not really
worth it, because nobody would use them in production anyway. For
this reason, we decided to make CONFIG_PM_SLEEP select
CONFIG_PM_RUNTIME and that lead to the conclusion that the latter
became redundant and CONFIG_PM could be used instead of it. The
material here makes that replacement in a major part of the tree, but
there will be at least one more batch of that in the second part of
the merge window.
Specifics:
- Support for retrieving device properties information from ACPI _DSD
device configuration objects and a unified device properties
interface for device drivers (and subsystems) on top of that. As
stated above, this works with Device Trees and ACPI and allows
device drivers to be written in a platform firmware (DT or ACPI)
agnostic way. The at25, leds-gpio and gpio_keys_polled drivers are
now going to use this new interface and the GPIO subsystem is
additionally modified to allow device drivers to assign names to
GPIO resources returned by ACPI _CRS objects (in case _DSD is not
present or does not provide the expected data). The changes in
this set are mostly from Mika Westerberg, Rafael J Wysocki, Aaron
Lu, and Darren Hart with some fixes from others (Fabio Estevam,
Geert Uytterhoeven).
- Support for Hardware Managed Performance States (HWP) as described
in Volume 3, section 14.4, of the Intel SDM in the intel_pstate
driver. CPUID is used to detect whether or not the feature is
supported by the processor. If supported, it will be enabled
automatically unless the intel_pstate=no_hwp switch is present in
the kernel command line. From Dirk Brandewie.
- New Intel Broadwell-H ID for intel_pstate (Dirk Brandewie).
- Support for firmware interface based on ACPI operation regions used
by the PMIC chips on the Intel Baytrail-T and Baytrail-T-CR
platforms for power resource control and thermal management (Aaron
Lu).
- Limited support for retrieving off-the-hierarchy dependencies
between devices from ACPI _DEP device configuration objects and
deferred probing support for the ACPI battery driver based on the
_DEP information to make that driver work on Asus T100A (Lan
Tianyu).
- New cpufreq driver for the Loongson1B processor (Kelvin Cheung).
- ACPICA update to upstream revision 20141107 which only affects
tools (Bob Moore).
- Fixes for race conditions in the ACPICA's interrupt handling code
and in the ACPI code related to system suspend and resume (Lv Zheng
and Rafael J Wysocki).
- ACPI core fix for an RCU-related issue in the ioremap() regions
management code that slowed down significantly after CPUs had been
allowed to enter idle states even if they'd had RCU callbakcs
queued and triggered some problems in certain proprietary graphics
driver (and elsewhere). The fix replaces synchronize_rcu() in that
code with synchronize_rcu_expedited() which makes the issue go
away. From Konstantin Khlebnikov.
- ACPI LPSS (Low-Power Subsystem) driver fix to handle power
management of the DMA engine included into the LPSS correctly. The
problem is that the DMA engine doesn't have ACPI PM support of its
own and it simply is turned off when the last LPSS device having
ACPI PM support goes into D3cold. To work around that, the PM
domain used by the ACPI LPSS driver is redesigned so at least one
device with ACPI PM support will be on as long as the DMA engine is
in use. From Andy Shevchenko.
- ACPI backlight driver fix to avoid using it on "Win8-compatible"
systems where it doesn't work and where it was used by default by
mistake (Aaron Lu).
- Assorted minor ACPI core fixes and cleanups from Tomasz Nowicki,
Sudeep Holla, Huang Rui, Hanjun Guo, Fabian Frederick, and Ashwin
Chaugule (mostly related to the upcoming ARM64 support).
- Intel RAPL (Running Average Power Limit) power capping driver fixes
and improvements including new processor IDs (Jacob Pan).
- Generic power domains modification to power up domains after
attaching devices to them to meet the expectations of device
drivers and bus types assuming devices to be accessible at probe
time (Ulf Hansson).
- Preliminary support for controlling device clocks from the generic
power domains core code and modifications of the ARM/shmobile
platform to use that feature (Ulf Hansson).
- Assorted minor fixes and cleanups of the generic power domains core
code (Ulf Hansson, Geert Uytterhoeven).
- Assorted minor fixes and cleanups of the device clocks control code
in the PM core (Geert Uytterhoeven, Grygorii Strashko).
- Consolidation of device power management Kconfig options by making
CONFIG_PM_SLEEP select CONFIG_PM_RUNTIME and removing the latter
which is now redundant (Rafael J Wysocki and Kevin Hilman). That
is the first batch of the changes needed for this purpose.
- Core device runtime power management support code cleanup related
to the execution of callbacks (Andrzej Hajda).
- cpuidle ARM support improvements (Lorenzo Pieralisi).
- cpuidle cleanup related to the CPUIDLE_FLAG_TIME_VALID flag and a
new MAINTAINERS entry for ARM Exynos cpuidle (Daniel Lezcano and
Bartlomiej Zolnierkiewicz).
- New cpufreq driver callback (->ready) to be executed when the
cpufreq core is ready to use a given policy object and cpufreq-dt
driver modification to use that callback for cooling device
registration (Viresh Kumar).
- cpufreq core fixes and cleanups (Viresh Kumar, Vince Hsu, James
Geboski, Tomeu Vizoso).
- Assorted fixes and cleanups in the cpufreq-pcc, intel_pstate,
cpufreq-dt, pxa2xx cpufreq drivers (Lenny Szubowicz, Ethan Zhao,
Stefan Wahren, Petr Cvek).
- OPP (Operating Performance Points) framework modification to allow
OPPs to be removed too and update of a few cpufreq drivers
(cpufreq-dt, exynos5440, imx6q, cpufreq) to remove OPPs (added
during initialization) on driver removal (Viresh Kumar).
- Hibernation core fixes and cleanups (Tina Ruchandani and Markus
Elfring).
- PM Kconfig fix related to CPU power management (Pankaj Dubey).
- cpupower tool fix (Prarit Bhargava)"
* tag 'pm+acpi-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (120 commits)
i2c-omap / PM: Drop CONFIG_PM_RUNTIME from i2c-omap.c
dmaengine / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
tools: cpupower: fix return checks for sysfs_get_idlestate_count()
drivers: sh / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
e1000e / igb / PM: Eliminate CONFIG_PM_RUNTIME
MMC / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
MFD / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
misc / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
media / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
input / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
leds: leds-gpio: Fix multiple instances registration without 'label' property
iio / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
hsi / OMAP / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
i2c-hid / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
drm / exynos / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
gpio / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
hwrandom / exynos / PM: Use CONFIG_PM in #ifdef
block / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
USB / PM: Drop CONFIG_PM_RUNTIME from the USB core
PM: Merge the SET*_RUNTIME_PM_OPS() macros
...
After commit b2b49ccbdd (PM: Kconfig: Set PM_RUNTIME if PM_SLEEP is
selected) PM_RUNTIME is always set if PM is set, so #ifdef blocks
depending on CONFIG_PM_RUNTIME may now be changed to depend on
CONFIG_PM.
Replace CONFIG_PM_RUNTIME with CONFIG_PM in drivers/gpio/gpio-omap.c.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Alexandre Courbot <acourbot@nvidia.com>
Acked-by: Javier Martinez Canillas <javier@dowhile0.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
The SET_PM_RUNTIME_PM_OPS() and SET_RUNTIME_PM_OPS() macros are
identical except that one of them is not empty for CONFIG_PM set,
while the other one is not empty for CONFIG_PM_RUNTIME set,
respectively.
However, after commit b2b49ccbdd (PM: Kconfig: Set PM_RUNTIME if
PM_SLEEP is selected) PM_RUNTIME is always set if PM is set, so one
of these macros is now redundant.
For this reason, replace SET_PM_RUNTIME_PM_OPS() with
SET_RUNTIME_PM_OPS() everywhere and redefine the SET_PM_RUNTIME_PM_OPS
symbol as SET_RUNTIME_PM_OPS in case new code is starting to use the
macro being removed here.
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Gpio-ranges property is useful to represent which GPIOs correspond
to which pins on which pin controllers. But there may be some gpios
without pinctrl operation. So check whether gpio-ranges property
exists in device node first.
Signed-off-by: Yunlei He <heyunlei@huawei.com>
Signed-off-by: Xinwei Kong <kong.kongxinwei@hisilicon.com>
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Default is active low, but if property is specified in DT set INTPOL flag.
Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Commit 14e85c0e69 ("gpio: remove gpio_descs global array") changed
gpio_to_desc()'s behavior to return NULL not only for GPIOs numbers
not in the valid range, but also for all GPIOs whose controller has not
been probed yet. Although this behavior is more correct (nothing hints
that these GPIO numbers will be populated later), this affects
gpio_request() and gpio_request_one() which call gpiod_request() with a
NULL descriptor, causing it to return -EINVAL instead of the expected
-EPROBE_DEFER for a non-probed GPIO.
gpiod_request() is only called with a descriptor obtained from
gpio_to_desc() from these two functions, so address the issue there.
Other ways to obtain GPIOs rely on well-defined mappings and can thus
return -EPROBE_DEFER only for relevant GPIOs, and are thus not affected
by this issue.
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Although gpiod_get_direction() can be considered side-effect free for
consumers, its internals involve setting or clearing bits in the
affected GPIO descriptor, for which we need to force-cast the const
descriptor variable to non-const. This could lead to incorrect behavior
if the compiler decides to optimize here, so remove this const
attribute. The intent is to make gpiod_get_direction() private anyway,
so it does not really matter.
Reported-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Replace the ARCH_NR_GPIOS-sized static array of GPIO descriptors by
dynamically-allocated arrays for each GPIO chip.
This change makes gpio_to_desc() perform in O(n) (where n is the number
of GPIO chips registered) instead of O(1), however since n is rarely
bigger than 1 or 2 no noticeable performance issue is expected.
Besides this provides more incentive for GPIO consumers to move to the
gpiod interface. One could use a O(log(n)) structure to link the GPIO
chips together, but considering the low limit of n the hypothetical
performance benefit is probably not worth the added complexity.
This patch uses kcalloc() in gpiochip_add(), which removes the ability
to add a chip before kcalloc() can operate. I am not aware of such
cases, but if someone bisects up to this patch then I will be proven
wrong...
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
gpiolib's gpiod_get_direction() function returns the EINVAL error
if .get_direction callback is not defined.
The patch implements the callback for mxs chip which is useful
for debugging.
Inspired by arch/arm/mach-at91/gpio.c
On the moment the patch is required to get the patch
"serial: mxs-auart: enable PPS support" working.
It is planned to introduce new mctrl_gpio helpers to avoid
gpiod_get_direction() function.
Signed-off-by: Janusz Uzycki <j.uzycki@elproma.com.pl>
Acked-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use dynamic allocation of GPIOs instead of looking at the gpio%u alias
in DT.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
It doesn't make much sense to make some (possible expensive) calls to
gpio_is_valid() first, and to ignore the result if the base number is
negative. Check for a positive base number first.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Currently this implementation only supports one IRQ for (all) SPI devices
using the same chip select.
Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Request a shared interrupt when requesting a mcp23s08 GPIO interrupt.
Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
If devm_request_threaded_irq fails for some reason we call
mcp23s08_irq_teardown afterwards.
Do not free the unrequested interrupt in this case. free_irq can also be
omitted for the error free case because we use devm_request_threaded_irq.
Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add a set_multiple function to the MPC8xxx GPIO chip driver and thereby allow
for actual performance improvements when setting multiple outputs
simultaneously. In my case the time needed to configure an FPGA goes down from
48 s to 20 s.
Change log:
v6: - rebase on current linux-gpio devel branch
v5: - no change
v4: - change interface of the set_multiple driver function to use
unsigned long as type for the bit fields
- use generic bitops (which also use unsigned long for bit fields)
v3: - change commit message
v2: - add this patch (v1 included only changes to gpiolib)
Signed-off-by: Rojhalat Ibrahim <imr@rtschenk.de>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Introduce new functions gpiod_set_array & gpiod_set_raw_array to the consumer
interface which allow setting multiple outputs with just one function call.
Also add an optional set_multiple function to the driver interface. Without an
implementation of that function in the chip driver outputs are set
sequentially.
Implementing the set_multiple function in a chip driver allows for:
- Improved performance for certain use cases. The original motivation for this
was the task of configuring an FPGA. In that specific case, where 9 GPIO
lines have to be set many times, configuration time goes down from 48 s to
20 s when using the new function.
- Simultaneous glitch-free setting of multiple pins on any kind of parallel
bus attached to GPIOs provided they all reside on the same chip and bank.
Limitations:
Performance is only improved for normal high-low outputs. Open drain and
open source outputs are always set separately from each other. Those kinds
of outputs could probably be accelerated in a similar way if we could
forgo the error checking when setting GPIO directions.
Change log:
v6: - rebase on current linux-gpio devel branch
v5: - check can_sleep property per chip
- remove superfluous checks
- supplement documentation
v4: - add gpiod_set_array function for setting logical values
- change interface of the set_multiple driver function to use
unsigned long as type for the bit fields
- use generic bitops (which also use unsigned long for bit fields)
- do not use ARCH_NR_GPIOS any more
v3: - add documentation
- change commit message
v2: - use descriptor interface
- allow arbitrary groups of GPIOs spanning multiple chips
Signed-off-by: Rojhalat Ibrahim <imr@rtschenk.de>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Reviewed-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
irq_of_parse_and_map() returns 0 on error, so testing for negative
result never works.
Signed-off-by: Dmitry Torokhov <dtor@chromium.org>
Acked-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The TC3589x driver is now a device tree-only driver, so we want
only dynamic IRQs and GPIO numbers from the tc3589x, no static
assignments.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch adds GPIO and IRQ support for the Diolan DLN-2 GPIO module.
Information about the USB protocol interface can be found in the
Programmer's Reference Manual [1], see section 2.9 for the GPIO
module commands and responses.
[1] https://www.diolan.com/downloads/dln-api-manual.pdf
Signed-off-by: Daniel Baluta <daniel.baluta@intel.com>
Signed-off-by: Octavian Purdila <octavian.purdila@intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The size_prop argument of the recently added function
acpi_dev_get_property_reference() is not used by the only current
caller of that function and is very unlikely to be used at any time
going forward.
Namely, for a property whose value is a list of items each containing
a references to a device object possibly accompanied by some integers,
the number of items in the list can always be computed as the number
of elements of type ACPI_TYPE_LOCAL_REFERENCE in the property package.
Thus it should never be necessary to provide an additional "cells"
property with a value equal to the number of items in that list. It
also should never be necessary to provide a "cells" property specifying
how many integers are supposed to be following each reference.
For this reason, drop the size_prop argument from
acpi_dev_get_property_reference() and update its caller accordingly.
Link: http://marc.info/?l=linux-kernel&m=141511255610556&w=2
Suggested-by: Grant Likely <grant.likely@linaro.org>
Acked-by: Grant Likely <grant.likely@linaro.org>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Provide a way for device drivers using GPIOs described by ACPI
GpioIo resources in _CRS to tell the GPIO subsystem what names
(connection IDs) to associate with specific GPIO pins defined
in there.
To do that, a driver needs to define a mapping table as a
NULL-terminated array of struct acpi_gpio_mapping objects
that each contain a name, a pointer to an array of line data
(struct acpi_gpio_params) objects and the size of that array.
Each struct acpi_gpio_params object consists of three fields,
crs_entry_index, line_index, active_low, representing the index of
the target GpioIo()/GpioInt() resource in _CRS starting from zero,
the index of the target line in that resource starting from zero,
and the active-low flag for that line, respectively.
Next, the mapping table needs to be passed as the second
argument to acpi_dev_add_driver_gpios() that will register it with
the ACPI device object pointed to by its first argument. That
should be done in the driver's .probe() routine.
On removal, the driver should unregister its GPIO mapping table
by calling acpi_dev_remove_driver_gpios() on the ACPI device
object where that table was previously registered.
Included are fixes from Mika Westerberg.
Acked-by: Alexandre Courbot <acourbot@nvidia.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Some drivers need to deal with only firmware representation of its
GPIOs. An example would be a GPIO button array driver where each button
is described as a separate firmware node in device tree. Typically these
child nodes do not have physical representation in the Linux device
model.
In order to help device drivers to handle such firmware child nodes we
add dev[m]_get_named_gpiod_from_child() that takes a child firmware
node pointer as its second argument (the first one is the parent device
itself), finds the GPIO using whatever is the underlying firmware
method, and requests the GPIO properly.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Alexandre Courbot <acourbot@nvidia.com>
Acked-by: Grant Likely <grant.likely@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This is actually a single device with two sets of identical registers,
which just happen to start from a different offset. Instead of having
separate GPIO chips created we consolidate them to be single GPIO chip.
In addition having a single GPIO chip allows us to handle ACPI GPIO
translation in the core in a more generic way, since the two GPIO chips
share the same parent ACPI device.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Grant Likely <grant.likely@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
With release of ACPI 5.1 and _DSD method we can finally name GPIOs (and
other things as well) returned by _CRS. Previously we were only able to
use integer index to find the corresponding GPIO, which is pretty error
prone if the order changes.
With _DSD we can now query GPIOs using name instead of an integer index,
like the below example shows:
// Bluetooth device with reset and shutdown GPIOs
Device (BTH)
{
Name (_HID, ...)
Name (_CRS, ResourceTemplate ()
{
GpioIo (Exclusive, PullUp, 0, 0, IoRestrictionInputOnly,
"\\_SB.GPO0", 0, ResourceConsumer) {15}
GpioIo (Exclusive, PullUp, 0, 0, IoRestrictionInputOnly,
"\\_SB.GPO0", 0, ResourceConsumer) {27, 31}
})
Name (_DSD, Package ()
{
ToUUID("daffd814-6eba-4d8c-8a91-bc9bbf4aa301"),
Package ()
{
Package () {"reset-gpio", Package() {^BTH, 1, 1, 0 }},
Package () {"shutdown-gpio", Package() {^BTH, 0, 0, 0 }},
}
})
}
The format of the supported GPIO property is:
Package () { "name", Package () { ref, index, pin, active_low }}
ref - The device that has _CRS containing GpioIo()/GpioInt() resources,
typically this is the device itself (BTH in our case).
index - Index of the GpioIo()/GpioInt() resource in _CRS starting from zero.
pin - Pin in the GpioIo()/GpioInt() resource. Typically this is zero.
active_low - If 1 the GPIO is marked as active_low.
Since ACPI GpioIo() resource does not have field saying whether it is
active low or high, the "active_low" argument can be used here. Setting
it to 1 marks the GPIO as active low.
In our Bluetooth example the "reset-gpio" refers to the second GpioIo()
resource, second pin in that resource with the GPIO number of 31.
This patch implements necessary support to gpiolib for extracting GPIOs
using _DSD device properties.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Grant Likely <grant.likely@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The GPIO resources (GpioIo/GpioInt) used in ACPI contain a GPIO number
which is relative to the hardware GPIO controller. Typically this number
can be translated directly to Linux GPIO number because the mapping is
pretty much 1:1.
However, when the GPIO driver is using pins exported by a pin controller
driver via set of GPIO ranges, the mapping might not be 1:1 anymore and
direct translation does not work.
In such cases we need to translate the ACPI GPIO number to be suitable for
the GPIO controller driver in question by checking all the pin controller
GPIO ranges under the given device and using those to get the proper GPIO
number.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This commit adds the implementation of ->suspend() and ->resume()
platform_driver hooks in order to save and restore the state of the
GPIO configuration. In order to achieve that, additional fields are
added to the mvebu_gpio_chip structure.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
irq_set_irq_wake() treats its second argument as a boolean. It is much
easier to read code when constant booleans are either 0 or 1!
This particular line of code distracted me somewhat when I was doing a bit of
work in a code browser since it (spuriously) got me worried that I had
misunderstood how irq_set_irq_wake() worked.
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
irq_set_irq_wake() treats its second argument as a boolean. It is much
easier to read code when constant booleans are either 0 or 1!
This particular line of code distracted me somewhat when I was doing a bit of
work in a code browser since it (spuriously) got me worried that I had
misunderstood how irq_set_irq_wake() worked.
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Alexandre Courbot <gnurou@gmail.com>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
[jkosina@suse.cz: alter subject to be more descriptive]
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This patch fix company name's spelling typo in module descriptions
and a Kconfig.
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Acked-by: Chris Snook <chris.snook@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This function actually operates on a gpio_chip, so its prefix should
reflect that fact for consistency with other functions defined in
gpio/driver.h.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Whereas the DWAPB driver does not really depend on the ARM
architecture, it uses [readl|writel]_relaxed() not found on
arch such as Blackfin, so restrict this to ARM until there is
another architecture that can make use of it.
It is also using the of_node of the gpiochip, so fix this
too by requiring OF_GPIO.
All error/warnings:
make.cross ARCH=blackfin
drivers/gpio/gpio-dwapb.c: In function 'dwapb_irq_handler':
drivers/gpio/gpio-dwapb.c:91:2: error: implicit declaration of function 'readl_relaxed' [-Werror=implicit-function-declaration]
drivers/gpio/gpio-dwapb.c: In function 'dwapb_configure_irqs':
drivers/gpio/gpio-dwapb.c:212:32: error: 'struct gpio_chip' has no member named 'of_node'
drivers/gpio/gpio-dwapb.c:221:16: error: 'struct gpio_chip' has no member named 'of_node'
drivers/gpio/gpio-dwapb.c: In function 'dwapb_gpio_add_port':
drivers/gpio/gpio-dwapb.c:331:14: error: 'struct gpio_chip' has no member named 'of_node'
cc1: some warnings being treated as errors
Cc: Jamie Iles <jamie@jamieiles.com>
Cc: Alan Tull <atull@altera.com>
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add a gpiolib and IRQ chip driver for Vybrid ARM SoC using the
Vybrid's GPIO and PORT module. The driver is instanced once per
each GPIO/PORT module pair and handles 32 GPIO's.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Acked-by: Shawn Guo <shawn.guo@freescale.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This change switches to devm_request_region to request region
and hence simplifies the module unload and does away with
release_region in remove function.
Cc: linux-gpio@vger.kernel.org
Signed-off-by: Pramod Gurav <pramod.gurav@smartplayin.com>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
