A warning would be printed for every packet that
is transmitted if the rate control information isn't
setup. Change this to WARN_ON_ONCE.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We do not know what max power to allow until a device is targeting
a channel, therefore only allow changing tx power if a channel is defined.
Also make use of the channel's max power setting as defined by
regulatory rules before allowing the user to use the requested power
setting. If the user asked us to figure it out we use the max allowed
by regulatory.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch add a check on the return value of dev_alloc_skb() in
ieee80211_sta_join_ibss() in net/mac80211/mlme.c.
Signed-off-by: Rami Rosen <ramirose@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It is unnecessary and of questionable value. Also remove
is_empty_ssid, as it is also unnecessary.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We never clearly defined the semantics of the sta_notify callback
and it was originally posted for iwlwifi which still doesn't use
it at all. With the recent HT rework ath9k started relying on it,
but I made a mistake there in that I made ath9k assume the HT
information has already been filled in at sta_notify time. This
isn't a hard thing to do, so do it.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We really only need to know the last request at each point in time.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This mutex is wrong, we use cfg80211_drv_mutex (which should
possibly be renamed to just cfg80211_mutex) everywhere except
in one place, fix that and get rid of the extra mutex.
Also get rid of a spurious regulatory_requests list definition.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This function requires an internal lock to be held, so it cannot
be published to other modules in the kernel.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The two new commands are NL80211_CMD_GET_MESH_PARAMS and
NL80211_CMD_SET_MESH_PARAMS. There is a new attribute enum,
NL80211_ATTR_MESH_PARAMS, which enumerates the various mesh configuration
parameters.
Moved struct mesh_config from mac80211/ieee80211_i.h to net/cfg80211.h.
nl80211_get_mesh_params and nl80211_set_mesh_params unpack the netlink messages
and ask the driver to get or set the configuration. This is done via two new
function stubs, get_mesh_params and set_mesh_params, in struct cfg80211_ops.
Signed-off-by: Colin McCabe <colin@cozybit.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
I noticed that when for some reason [1] the probe or auth times
out, wpa_supplicant doesn't realise this and only tries the next
AP when it runs into its own timeout, which is ten seconds, and
that's quite long. Fix this by making mac80211 notify userspace
that it didn't associate.
[1] my wrt350n in mixed B/G/HT mode often runs into this, maybe
it's because one of the antennas is broken off and for whatever
reason it decides to use that antenna to transmit the response
frames (auth, probe); I do see beacons fine so it's not totally
broken. Works fine in pure-G mode.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
"Clearing" the rate control algorithm is pointless, none of
the algorithms actually uses this operation and it's not even
invoked properly for all channel switching. Also, there's no
need to since rate control algorithms work per station.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch enhances minstrel's performance for non-MRR setups,
by preventing it from sampling slower rates with >95% success
probability and by putting at least 1 non-sample frame between
several sample frames.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
NLA_NESTED attributes cannot be empty, but we want to be able to
specify "no flags" (empty attribute) vs. "no change" (no attribute).
Therefore, remove the NLA_NESTED policy so it can work as an empty
attribute.
I guess I should have used a u32 for these flags instead, but we're
stuck with it now. Haven't noticed earlier because of a bug in iw...
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This makes CONFIG_IEEE80211 invisible. The drivers that require it
(ipw2100, ipw2200, hostap) select it, and everybody else really
shouldn't even think about using it. Also, since there really is
no point in compiling anything without crypto support these days,
remove the crypto options and just enable them, leaving only the
debugging option which only shows up when a driver is select that
requires it. This makes it hard to enable, but most people wouldn't
want to anyway.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
So after the previous changes we were still unhappy with how
convoluted the API is and decided to make things simpler for
everybody. This completely changes the rate control API, now
taking into account 802.11n with MCS rates and more control,
most drivers don't support that though.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Just to catch bugs when changing mac80211.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The HT handling has the following deficiencies, which I've
(partially) fixed:
* it always uses the AP info even if there is no AP,
hence has no chance of working as an AP
* it pretends to be HW config, but really is per-BSS
* channel sanity checking is left to the drivers
* it generally lets the driver control too much
HT enabling is still wrong with this patch if you have more than
one virtual STA mode interface, but that never happens currently.
Once WDS, IBSS or AP/VLAN gets HT capabilities, it will also be
wrong, see the comment in ieee80211_enable_ht().
Additionally, this fixes a number of bugs:
* mac80211: ieee80211_set_disassoc doesn't notify the driver any
more since the refactoring
* iwl-agn-rs: always uses the HT capabilities from the wrong stuff
mac80211 gives it rather than the actual peer STA
* ath9k: a number of bugs resulting from the broken HT API
I'm not entirely happy with putting the HT capabilities into
struct ieee80211_sta as restricted to our own HT TX capabilities,
but I see no cleaner solution for now.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Move bss_conf into the vif struct so that drivers can
access it during ->tx without having to store it in
the private data or similar. No driver updates because
this is only for when they want to start using it.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of having a separate callback, use the HW config callback
with a new flag to change retry limits.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This exports the local HT capabilities in nl80211.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
I've come to think that not providing sequence numbers for
the normal STA mode case was a mistake, at least two drivers
now had to implement code they wouldn't otherwise need, and
I believe at76_usb and adm8211 might be broken.
This patch makes mac80211 assign a sequence number to all
those frames that need one except beacons. That means that
if a driver only implements modes that do not do beaconing
it need not worry about the sequence number.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Limit the number of "expensive" rfkill workqueue operations per second, in
order to not hog system resources too much when faced with a rogue source
of rfkill input events.
The old rfkill-input code (before it was refactored) had such a limit in
place. It used to drop new events that were past the rate limit. This
behaviour was not implemented as an anti-DoS measure, but rather as an
attempt to work around deficiencies in input device drivers which would
issue multiple KEY_FOO events too soon for a given key FOO (i.e. ones that
do not implement mechanical debouncing properly).
However, we can't really expect such issues to be worked around by every
input handler out there, and also by every userspace client of input
devices. It is the input device driver's responsability to do debouncing
instead of spamming the input layer with bogus events.
The new limiter code is focused only on anti-DoS behaviour, and tries to
not lose events (instead, it coalesces them when possible).
The transmitters are updated once every 200ms, maximum. Care is taken not
to delay a request to _enter_ rfkill transmitter Emergency Power Off (EPO)
mode.
If mistriggered (e.g. by a jiffies counter wrap), the code delays processing
*once* by 200ms.
Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Cc: Ivo van Doorn <IvDoorn@gmail.com>
Cc: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rfkill_resume() would always restore the rfkill controller state to its
pre-suspend state.
Now that we know when we are under EPO, kick the rfkill controller to
SOFT_BLOCKED state instead of to its pre-suspend state when it is resumed
while EPO mode is active.
Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Cc: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add of software-based sanity to rfkill and rfkill-input so that it can
reproduce what hardware-based EPO switches do, blocking all transmitters
and locking down any further attempts to unblock them until the switch is
deactivated.
rfkill-input is responsible for issuing the EPO control requests, like
before.
While an rfkill EPO is active, all transmitters are locked to one of the
BLOCKED states and all attempts to change that through the rfkill API
(userspace and kernel) will be either ignored or return -EPERM errors.
The lock will be released upon receipt of EV_SW SW_RFKILL_ALL ON by
rfkill-input, or should modular rfkill-input be unloaded.
This makes rfkill and rfkill-input extend the operation of an existing
wireless master kill switch to all wireless devices in the system, even
those that are not under hardware or firmware control.
Since the above is the expected operational behavior for the master rfkill
switch, the EPO lock functionality is not optional.
Also, extend rfkill-input to allow for three different behaviors when it
receives an EV_SW SW_RFKILL_ALL ON input event. The user can set which
behavior he wants through the master_switch_mode parameter:
master_switch_mode = 0: EV_SW SW_RFKILL_ALL ON just unlocks rfkill
controller state changes (so that the rfkill userspace and kernel APIs can
now be used to change rfkill controller states again), but doesn't change
any of their states (so they will all remain blocked). This is the safest
mode of operation, as it requires explicit operator action to re-enable a
transmitter.
master_switch_mode = 1: EV_SW SW_RFKILL_ALL ON causes rfkill-input to
attempt to restore the system to the state before the last EV_SW
SW_RFKILL_ALL OFF event, or to the default global states if no EV_SW
SW_RFKILL_ALL OFF ever happened. This is the recommended mode of
operation for laptops.
master_switch_mode = 2: tries to unblock all rfkill controllers (i.e.
enable all transmitters) when an EV_SW SW_RFKILL_ALL ON event is received.
This is the default mode of operation, as it mimics the previous behavior
of rfkill-input.
In order to implement these features in a clean way, the entire event
handling of rfkill-input was refactored into a single worker function.
Protection against input event DoS (repeatedly firing rfkill events for
rfkill-input to process) was removed during the code refactoring. It will
be added back in a future patch.
Note that with these changes, rfkill-input doesn't need to explicitly
handle any radio types for which KEY_<radio type> or SW_<radio type> events
do not exist yet.
Code to handle EV_SW SW_{WLAN,WWAN,BLUETOOTH,WIMAX,...} was added as it
might be needed in the future (and its implementation is not that obvious),
but is currently #ifdef'd out to avoid wasting resources.
Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Cc: Ivo van Doorn <IvDoorn@gmail.com>
Cc: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Export the the global switch states to rfkill-input. This is needed to
properly implement KEY_* handling without disregarding the initial state.
Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Cc: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Apparently, many applications don't expect to get EAGAIN from fd read/write
operations, since POSIX doesn't mandate it.
Use mutex_lock_killable instead of mutex_lock_interruptible, which won't
cause issues.
Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Cc: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This makes mac80211 notify the driver which configuration
actually changed, e.g. channel etc.
No driver changes, this is just plumbing, driver authors are
expected to act on this if they want to.
Also remove the HW CONFIG debug printk, it's incorrect, often
we configure something else.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch cleans up a number of things:
* the unusable definition of the HT capabilities/HT information
information elements
* variable names that are hard to understand
* mac80211: move ieee80211_handle_ht to ht.c and remove the unused
enable_ht parameter
* mac80211: fix bug with MCS rate 32 in ieee80211_handle_ht
* mac80211: fix bug with casting the result of ieee80211_bss_get_ie
to an information element _contents_ rather than the
whole element, add size checking (another out-of-bounds
access bug fixed!)
* mac80211: remove some unused return values in favour of BUG_ON
checking
* a few minor other things
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch removes unused definition of struct sta_attribute
in net/mac80211/ieee80211_i.h.
Signed-off-by: Rami Rosen <ramirose@gmail.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch makes mac80211 handle short slot requests from the AP
properly. Also warn about uses of IEEE80211_CONF_SHORT_SLOT_TIME
and optimise out the code since it cannot ever be hit anyway.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The antenna gain isn't exactly configurable, despite the belief of
some unnamed individual who thinks that the EEPROM might influence
it.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Warn when ieee80211_hw_config returns an error, it shouldn't
happen; remove a number of printks that would happen in such
a case and one printk that is user-triggerable.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This isn't used by anyone, if we ever need it we can add
it back, until then it's useless.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Nothing very interesting, some checkpatch inspired stuff,
some other things.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
These parameters shouldn't be configurable via debugfs, if they
need to be configurable nl80211 support has to be added, if not
then they don't need to be writable here either.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: Javier Cardona <javier@cozybit.com>
Cc: Luis Carlos Cobo <luisca@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This code uses static variables and thus cannot be kept.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Using NIPQUAD() with NIPQUAD_FMT, %d.%d.%d.%d or %u.%u.%u.%u
can be replaced with %pI4
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using NIPQUAD() with NIPQUAD_FMT, %d.%d.%d.%d or %u.%u.%u.%u
can be replaced with %pI4
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using NIPQUAD() with NIPQUAD_FMT, %d.%d.%d.%d or %u.%u.%u.%u
can be replaced with %pI4
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using NIPQUAD() with NIPQUAD_FMT, %d.%d.%d.%d or %u.%u.%u.%u
can be replaced with %pI4
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds qdisc_peek_dequeued() wrapper to emulate peek method
with qdisc->dequeue() and storing "peeked" skb in qdisc->gso_skb until
dequeuing. This is mainly for compatibility reasons not to break some
strange configs because peeking is expected for non-work-conserving
parent qdiscs to query work-conserving child qdiscs.
This implementation requires using qdisc_dequeue_peeked() wrapper
instead of directly calling qdisc->dequeue() for all qdiscs ever
querried with qdisc->ops->peek() or qdisc_peek_dequeued().
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use qdisc->ops->peek() instead of ->dequeue() & ->requeue() pair.
After this patch the only remaining user of qdisc->ops->requeue() is
netem_enqueue(). Based on ideas of Herbert Xu, Patrick McHardy and
David S. Miller.
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add qdisc->ops->peek() implementation for work-conserving qdiscs.
With feedback from Patrick McHardy.
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>