When running as a nested hypervisor, this avoids reading hypervisor
privileged registers (specifically HFSCR, LPIDR and LPCR) at startup;
instead reasonable default values are used. This also avoids writing
LPIDR in the single-vcpu entry/exit path.
Also, this removes the check for CPU_FTR_HVMODE in kvmppc_mmu_hv_init()
since its only caller already checks this.
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This is only done at level 0, since only level 0 knows which physical
CPU a vcpu is running on. This does for nested guests what L0 already
did for its own guests, which is to flush the TLB on a pCPU when it
goes to run a vCPU there, and there is another vCPU in the same VM
which previously ran on this pCPU and has now started to run on another
pCPU. This is to handle the situation where the other vCPU touched
a mapping, moved to another pCPU and did a tlbiel (local-only tlbie)
on that new pCPU and thus left behind a stale TLB entry on this pCPU.
This introduces a limit on the the vcpu_token values used in the
H_ENTER_NESTED hcall -- they must now be less than NR_CPUS.
[paulus@ozlabs.org - made prev_cpu array be short[] to reduce
memory consumption.]
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Suraj Jitindar Singh <sjitindarsingh@gmail.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This adds code to call the H_TLB_INVALIDATE hypercall when running as
a guest, in the cases where we need to invalidate TLBs (or other MMU
caches) as part of managing the mappings for a nested guest. Calling
H_TLB_INVALIDATE lets the nested hypervisor inform the parent
hypervisor about changes to partition-scoped page tables or the
partition table without needing to do hypervisor-privileged tlbie
instructions.
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
When running a nested (L2) guest the guest (L1) hypervisor will use
the H_TLB_INVALIDATE hcall when it needs to change the partition
scoped page tables or the partition table which it manages. It will
use this hcall in the situations where it would use a partition-scoped
tlbie instruction if it were running in hypervisor mode.
The H_TLB_INVALIDATE hcall can invalidate different scopes:
Invalidate TLB for a given target address:
- This invalidates a single L2 -> L1 pte
- We need to invalidate any L2 -> L0 shadow_pgtable ptes which map the L2
address space which is being invalidated. This is because a single
L2 -> L1 pte may have been mapped with more than one pte in the
L2 -> L0 page tables.
Invalidate the entire TLB for a given LPID or for all LPIDs:
- Invalidate the entire shadow_pgtable for a given nested guest, or
for all nested guests.
Invalidate the PWC (page walk cache) for a given LPID or for all LPIDs:
- We don't cache the PWC, so nothing to do.
Invalidate the entire TLB, PWC and partition table for a given/all LPIDs:
- Here we re-read the partition table entry and remove the nested state
for any nested guest for which the first doubleword of the partition
table entry is now zero.
The H_TLB_INVALIDATE hcall takes as parameters the tlbie instruction
word (of which only the RIC, PRS and R fields are used), the rS value
(giving the lpid, where required) and the rB value (giving the IS, AP
and EPN values).
[paulus@ozlabs.org - adapted to having the partition table in guest
memory, added the H_TLB_INVALIDATE implementation, removed tlbie
instruction emulation, reworded the commit message.]
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Suraj Jitindar Singh <sjitindarsingh@gmail.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
When a host (L0) page which is mapped into a (L1) guest is in turn
mapped through to a nested (L2) guest we keep a reverse mapping (rmap)
so that these mappings can be retrieved later.
Whenever we create an entry in a shadow_pgtable for a nested guest we
create a corresponding rmap entry and add it to the list for the
L1 guest memslot at the index of the L1 guest page it maps. This means
at the L1 guest memslot we end up with lists of rmaps.
When we are notified of a host page being invalidated which has been
mapped through to a (L1) guest, we can then walk the rmap list for that
guest page, and find and invalidate all of the corresponding
shadow_pgtable entries.
In order to reduce memory consumption, we compress the information for
each rmap entry down to 52 bits -- 12 bits for the LPID and 40 bits
for the guest real page frame number -- which will fit in a single
unsigned long. To avoid a scenario where a guest can trigger
unbounded memory allocations, we scan the list when adding an entry to
see if there is already an entry with the contents we need. This can
occur, because we don't ever remove entries from the middle of a list.
A struct nested guest rmap is a list pointer and an rmap entry;
----------------
| next pointer |
----------------
| rmap entry |
----------------
Thus the rmap pointer for each guest frame number in the memslot can be
either NULL, a single entry, or a pointer to a list of nested rmap entries.
gfn memslot rmap array
-------------------------
0 | NULL | (no rmap entry)
-------------------------
1 | single rmap entry | (rmap entry with low bit set)
-------------------------
2 | list head pointer | (list of rmap entries)
-------------------------
The final entry always has the lowest bit set and is stored in the next
pointer of the last list entry, or as a single rmap entry.
With a list of rmap entries looking like;
----------------- ----------------- -------------------------
| list head ptr | ----> | next pointer | ----> | single rmap entry |
----------------- ----------------- -------------------------
| rmap entry | | rmap entry |
----------------- -------------------------
Signed-off-by: Suraj Jitindar Singh <sjitindarsingh@gmail.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Consider a normal (L1) guest running under the main hypervisor (L0),
and then a nested guest (L2) running under the L1 guest which is acting
as a nested hypervisor. L0 has page tables to map the address space for
L1 providing the translation from L1 real address -> L0 real address;
L1
|
| (L1 -> L0)
|
----> L0
There are also page tables in L1 used to map the address space for L2
providing the translation from L2 real address -> L1 read address. Since
the hardware can only walk a single level of page table, we need to
maintain in L0 a "shadow_pgtable" for L2 which provides the translation
from L2 real address -> L0 real address. Which looks like;
L2 L2
| |
| (L2 -> L1) |
| |
----> L1 | (L2 -> L0)
| |
| (L1 -> L0) |
| |
----> L0 --------> L0
When a page fault occurs while running a nested (L2) guest we need to
insert a pte into this "shadow_pgtable" for the L2 -> L0 mapping. To
do this we need to:
1. Walk the pgtable in L1 memory to find the L2 -> L1 mapping, and
provide a page fault to L1 if this mapping doesn't exist.
2. Use our L1 -> L0 pgtable to convert this L1 address to an L0 address,
or try to insert a pte for that mapping if it doesn't exist.
3. Now we have a L2 -> L0 mapping, insert this into our shadow_pgtable
Once this mapping exists we can take rc faults when hardware is unable
to automatically set the reference and change bits in the pte. On these
we need to:
1. Check the rc bits on the L2 -> L1 pte match, and otherwise reflect
the fault down to L1.
2. Set the rc bits in the L1 -> L0 pte which corresponds to the same
host page.
3. Set the rc bits in the L2 -> L0 pte.
As we reuse a large number of functions in book3s_64_mmu_radix.c for
this we also needed to refactor a number of these functions to take
an lpid parameter so that the correct lpid is used for tlb invalidations.
The functionality however has remained the same.
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Suraj Jitindar Singh <sjitindarsingh@gmail.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
When we are running as a nested hypervisor, we use a hypercall to
enter the guest rather than code in book3s_hv_rmhandlers.S. This means
that the hypercall handlers listed in hcall_real_table never get called.
There are some hypercalls that are handled there and not in
kvmppc_pseries_do_hcall(), which therefore won't get processed for
a nested guest.
To fix this, we add cases to kvmppc_pseries_do_hcall() to handle those
hypercalls, with the following exceptions:
- The HPT hypercalls (H_ENTER, H_REMOVE, etc.) are not handled because
we only support radix mode for nested guests.
- H_CEDE has to be handled specially because the cede logic in
kvmhv_run_single_vcpu assumes that it has been processed by the time
that kvmhv_p9_guest_entry() returns. Therefore we put a special
case for H_CEDE in kvmhv_p9_guest_entry().
For the XICS hypercalls, if real-mode processing is enabled, then the
virtual-mode handlers assume that they are being called only to finish
up the operation. Therefore we turn off the real-mode flag in the XICS
code when running as a nested hypervisor.
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This adds code to call the H_IPI and H_EOI hypercalls when we are
running as a nested hypervisor (i.e. without the CPU_FTR_HVMODE cpu
feature) and we would otherwise access the XICS interrupt controller
directly or via an OPAL call.
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This adds a new hypercall, H_ENTER_NESTED, which is used by a nested
hypervisor to enter one of its nested guests. The hypercall supplies
register values in two structs. Those values are copied by the level 0
(L0) hypervisor (the one which is running in hypervisor mode) into the
vcpu struct of the L1 guest, and then the guest is run until an
interrupt or error occurs which needs to be reported to L1 via the
hypercall return value.
Currently this assumes that the L0 and L1 hypervisors are the same
endianness, and the structs passed as arguments are in native
endianness. If they are of different endianness, the version number
check will fail and the hcall will be rejected.
Nested hypervisors do not support indep_threads_mode=N, so this adds
code to print a warning message if the administrator has set
indep_threads_mode=N, and treat it as Y.
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This starts the process of adding the code to support nested HV-style
virtualization. It defines a new H_SET_PARTITION_TABLE hypercall which
a nested hypervisor can use to set the base address and size of a
partition table in its memory (analogous to the PTCR register).
On the host (level 0 hypervisor) side, the H_SET_PARTITION_TABLE
hypercall from the guest is handled by code that saves the virtual
PTCR value for the guest.
This also adds code for creating and destroying nested guests and for
reading the partition table entry for a nested guest from L1 memory.
Each nested guest has its own shadow LPID value, different in general
from the LPID value used by the nested hypervisor to refer to it. The
shadow LPID value is allocated at nested guest creation time.
Nested hypervisor functionality is only available for a radix guest,
which therefore means a radix host on a POWER9 (or later) processor.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
kvmppc_unmap_pte() does a sequence of operations that are open-coded in
kvm_unmap_radix(). This extends kvmppc_unmap_pte() a little so that it
can be used by kvm_unmap_radix(), and makes kvm_unmap_radix() call it.
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The radix page fault handler accounts for all cases, including just
needing to insert a pte. This breaks it up into separate functions for
the two main cases; setting rc and inserting a pte.
This allows us to make the setting of rc and inserting of a pte
generic for any pgtable, not specific to the one for this guest.
[paulus@ozlabs.org - reduced diffs from previous code]
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Suraj Jitindar Singh <sjitindarsingh@gmail.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
kvmppc_mmu_radix_xlate() is used to translate an effective address
through the process tables. The process table and partition tables have
identical layout. Exploit this fact to make the kvmppc_mmu_radix_xlate()
function able to translate either an effective address through the
process tables or a guest real address through the partition tables.
[paulus@ozlabs.org - reduced diffs from previous code]
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Suraj Jitindar Singh <sjitindarsingh@gmail.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
When destroying a VM we return the LPID to the pool, however we never
zero the partition table entry. This is instead done when we reallocate
the LPID.
Zero the partition table entry on VM teardown before returning the LPID
to the pool. This means if we were running as a nested hypervisor the
real hypervisor could use this to determine when it can free resources.
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Suraj Jitindar Singh <sjitindarsingh@gmail.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
When the 'regs' field was added to struct kvm_vcpu_arch, the code
was changed to use several of the fields inside regs (e.g., gpr, lr,
etc.) but not the ccr field, because the ccr field in struct pt_regs
is 64 bits on 64-bit platforms, but the cr field in kvm_vcpu_arch is
only 32 bits. This changes the code to use the regs.ccr field
instead of cr, and changes the assembly code on 64-bit platforms to
use 64-bit loads and stores instead of 32-bit ones.
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This adds a file called 'radix' in the debugfs directory for the
guest, which when read gives all of the valid leaf PTEs in the
partition-scoped radix tree for a radix guest, in human-readable
format. It is analogous to the existing 'htab' file which dumps
the HPT entries for a HPT guest.
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Currently the code for handling hypervisor instruction page faults
passes 0 for the flags indicating the type of fault, which is OK in
the usual case that the page is not mapped in the partition-scoped
page tables. However, there are other causes for hypervisor
instruction page faults, such as not being to update a reference
(R) or change (C) bit. The cause is indicated in bits in HSRR1,
including a bit which indicates that the fault is due to not being
able to write to a page (for example to update an R or C bit).
Not handling these other kinds of faults correctly can lead to a
loop of continual faults without forward progress in the guest.
In order to handle these faults better, this patch constructs a
"DSISR-like" value from the bits which DSISR and SRR1 (for a HISI)
have in common, and passes it to kvmppc_book3s_hv_page_fault() so
that it knows what caused the fault.
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This creates an alternative guest entry/exit path which is used for
radix guests on POWER9 systems when we have indep_threads_mode=Y. In
these circumstances there is exactly one vcpu per vcore and there is
no coordination required between vcpus or vcores; the vcpu can enter
the guest without needing to synchronize with anything else.
The new fast path is implemented almost entirely in C in book3s_hv.c
and runs with the MMU on until the guest is entered. On guest exit
we use the existing path until the point where we are committed to
exiting the guest (as distinct from handling an interrupt in the
low-level code and returning to the guest) and we have pulled the
guest context from the XIVE. At that point we check a flag in the
stack frame to see whether we came in via the old path and the new
path; if we came in via the new path then we go back to C code to do
the rest of the process of saving the guest context and restoring the
host context.
The C code is split into separate functions for handling the
OS-accessible state and the hypervisor state, with the idea that the
latter can be replaced by a hypercall when we implement nested
virtualization.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
[mpe: Fix CONFIG_ALTIVEC=n build]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Currently kvmppc_handle_exit_hv() is called with the vcore lock held
because it is called within a for_each_runnable_thread loop.
However, we already unlock the vcore within kvmppc_handle_exit_hv()
under certain circumstances, and this is safe because (a) any vcpus
that become runnable and are added to the runnable set by
kvmppc_run_vcpu() have their vcpu->arch.trap == 0 and can't actually
run in the guest (because the vcore state is VCORE_EXITING), and
(b) for_each_runnable_thread is safe against addition or removal
of vcpus from the runnable set.
Therefore, in order to simplify things for following patches, let's
drop the vcore lock in the for_each_runnable_thread loop, so
kvmppc_handle_exit_hv() gets called without the vcore lock held.
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This adds a parameter to __kvmppc_save_tm and __kvmppc_restore_tm
which allows the caller to indicate whether it wants the nonvolatile
register state to be preserved across the call, as required by the C
calling conventions. This parameter being non-zero also causes the
MSR bits that enable TM, FP, VMX and VSX to be preserved. The
condition register and DSCR are now always preserved.
With this, kvmppc_save_tm_hv and kvmppc_restore_tm_hv can be called
from C code provided the 3rd parameter is non-zero. So that these
functions can be called from modules, they now include code to set
the TOC pointer (r2) on entry, as they can call other built-in C
functions which will assume the TOC to have been set.
Also, the fake suspend code in kvmppc_save_tm_hv is modified here to
assume that treclaim in fake-suspend state does not modify any registers,
which is the case on POWER9. This enables the code to be simplified
quite a bit.
_kvmppc_save_tm_pr and _kvmppc_restore_tm_pr become much simpler with
this change, since they now only need to save and restore TAR and pass
1 for the 3rd argument to __kvmppc_{save,restore}_tm.
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This streamlines the first part of the code that handles a hypervisor
interrupt that occurred in the guest. With this, all of the real-mode
handling that occurs is done before the "guest_exit_cont" label; once
we get to that label we are committed to exiting to host virtual mode.
Thus the machine check and HMI real-mode handling is moved before that
label.
Also, the code to handle external interrupts is moved out of line, as
is the code that calls kvmppc_realmode_hmi_handler().
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This pulls out the assembler code that is responsible for saving and
restoring the PMU state for the host and guest into separate functions
so they can be used from an alternate entry path. The calling
convention is made compatible with C.
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Reviewed-by: Madhavan Srinivasan <maddy@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This is based on a patch by Suraj Jitindar Singh.
This moves the code in book3s_hv_rmhandlers.S that generates an
external, decrementer or privileged doorbell interrupt just before
entering the guest to C code in book3s_hv_builtin.c. This is to
make future maintenance and modification easier. The algorithm
expressed in the C code is almost identical to the previous
algorithm.
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This removes code that clears the external interrupt pending bit in
the pending_exceptions bitmap. This is left over from an earlier
iteration of the code where this bit was set when an escalation
interrupt arrived in order to wake the vcpu from cede. Currently
we set the vcpu->arch.irq_pending flag instead for this purpose.
Therefore there is no need to do anything with the pending_exceptions
bitmap.
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Currently we use two bits in the vcpu pending_exceptions bitmap to
indicate that an external interrupt is pending for the guest, one
for "one-shot" interrupts that are cleared when delivered, and one
for interrupts that persist until cleared by an explicit action of
the OS (e.g. an acknowledge to an interrupt controller). The
BOOK3S_IRQPRIO_EXTERNAL bit is used for one-shot interrupt requests
and BOOK3S_IRQPRIO_EXTERNAL_LEVEL is used for persisting interrupts.
In practice BOOK3S_IRQPRIO_EXTERNAL never gets used, because our
Book3S platforms generally, and pseries in particular, expect
external interrupt requests to persist until they are acknowledged
at the interrupt controller. That combined with the confusion
introduced by having two bits for what is essentially the same thing
makes it attractive to simplify things by only using one bit. This
patch does that.
With this patch there is only BOOK3S_IRQPRIO_EXTERNAL, and by default
it has the semantics of a persisting interrupt. In order to avoid
breaking the ABI, we introduce a new "external_oneshot" flag which
preserves the behaviour of the KVM_INTERRUPT ioctl with the
KVM_INTERRUPT_SET argument.
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
When doing nested virtualization, it is only necessary to do the
transactional memory hypervisor assist at level 0, that is, when
we are in hypervisor mode. Nested hypervisors can just use the TM
facilities as architected. Therefore we should clear the
CPU_FTR_P9_TM_HV_ASSIST bit when we are not in hypervisor mode,
along with the CPU_FTR_HVMODE bit.
Doing this will not change anything at this stage because the only
code that tests CPU_FTR_P9_TM_HV_ASSIST is in HV KVM, which currently
can only be used when when CPU_FTR_HVMODE is set.
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The kvmppc_gpa_to_ua() helper itself takes care of the permission
bits in the TCE and yet every single caller removes them.
This changes semantics of kvmppc_gpa_to_ua() so it takes TCEs
(which are GPAs + TCE permission bits) to make the callers simpler.
This should cause no behavioural change.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
At the moment if the PUT_TCE{_INDIRECT} handlers fail to update
the hardware tables, we print a warning once, clear the entry and
continue. This is so as at the time the assumption was that if
a VFIO device is hotplugged into the guest, and the userspace replays
virtual DMA mappings (i.e. TCEs) to the hardware tables and if this fails,
then there is nothing useful we can do about it.
However the assumption is not valid as these handlers are not called for
TCE replay (VFIO ioctl interface is used for that) and these handlers
are for new TCEs.
This returns an error to the guest if there is a request which cannot be
processed. By now the only possible failure must be H_TOO_HARD.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The userspace can request an arbitrary supported page size for a DMA
window and this works fine as long as the mapped memory is backed with
the pages of the same or bigger size; if this is not the case,
mm_iommu_ua_to_hpa{_rm}() fail and tables do not populated with
dangerously incorrect TCEs.
However since it is quite easy to misconfigure the KVM and we do not do
reverts to all changes made to TCE tables if an error happens in a middle,
we better do the acceptable page size validation before we even touch
the tables.
This enhances kvmppc_tce_validate() to check the hardware IOMMU page sizes
against the preregistered memory page sizes.
Since the new check uses real/virtual mode helpers, this renames
kvmppc_tce_validate() to kvmppc_rm_tce_validate() to handle the real mode
case and mirrors it for the virtual mode under the old name. The real
mode handler is not used for the virtual mode as:
1. it uses _lockless() list traversing primitives instead of RCU;
2. realmode's mm_iommu_ua_to_hpa_rm() uses vmalloc_to_phys() which
virtual mode does not have to use and since on POWER9+radix only virtual
mode handlers actually work, we do not want to slow down that path even
a bit.
This removes EXPORT_SYMBOL_GPL(kvmppc_tce_validate) as the validators
are static now.
From now on the attempts on mapping IOMMU pages bigger than allowed
will result in KVM exit.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
[mpe: Fix KVM_HV=n build]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
We return H_TOO_HARD from TCE update handlers when we think that
the next handler (realmode -> virtual mode -> user mode) has a chance to
handle the request; H_HARDWARE/H_CLOSED otherwise.
This changes the handlers to return H_TOO_HARD on every error giving
the userspace an opportunity to handle any request or at least log
them all.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The KVM TCE handlers are written in a way so they fail when either
something went horribly wrong or the userspace did some obvious mistake
such as passing a misaligned address.
We are going to enhance the TCE checker to fail on attempts to map bigger
IOMMU page than the underlying pinned memory so let's valitate TCE
beforehand.
This should cause no behavioral change.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
THP paths can defer splitting compound pages until after the actual
remap and TLB flushes to split a huge PMD/PUD. This causes radix
partition scope page table mappings to get out of synch with the host
qemu page table mappings.
This results in random memory corruption in the guest when running
with THP. The easiest way to reproduce is use KVM balloon to free up
a lot of memory in the guest and then shrink the balloon to give the
memory back, while some work is being done in the guest.
Cc: David Gibson <david@gibson.dropbear.id.au>
Cc: "Aneesh Kumar K.V" <aneesh.kumar@linux.ibm.com>
Cc: kvm-ppc@vger.kernel.org
Cc: linuxppc-dev@lists.ozlabs.org
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
At the moment the real mode handler of H_PUT_TCE calls iommu_tce_xchg_rm()
which in turn reads the old TCE and if it was a valid entry, marks
the physical page dirty if it was mapped for writing. Since it is in
real mode, realmode_pfn_to_page() is used instead of pfn_to_page()
to get the page struct. However SetPageDirty() itself reads the compound
page head and returns a virtual address for the head page struct and
setting dirty bit for that kills the system.
This adds additional dirty bit tracking into the MM/IOMMU API for use
in the real mode. Note that this does not change how VFIO and
KVM (in virtual mode) set this bit. The KVM (real mode) changes include:
- use the lowest bit of the cached host phys address to carry
the dirty bit;
- mark pages dirty when they are unpinned which happens when
the preregistered memory is released which always happens in virtual
mode;
- add mm_iommu_ua_mark_dirty_rm() helper to set delayed dirty bit;
- change iommu_tce_xchg_rm() to take the kvm struct for the mm to use
in the new mm_iommu_ua_mark_dirty_rm() helper;
- move iommu_tce_xchg_rm() to book3s_64_vio_hv.c (which is the only
caller anyway) to reduce the real mode KVM and IOMMU knowledge
across different subsystems.
This removes realmode_pfn_to_page() as it is not used anymore.
While we at it, remove some EXPORT_SYMBOL_GPL() as that code is for
the real mode only and modules cannot call it anyway.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Two small fixes for KVM on POWER machines; one fixes a bug where pages
might not get marked dirty, causing guest memory corruption on migration,
and the other fixes a bug causing reads from guest memory to use the
wrong guest real address for very large HPT guests (>256G of memory),
leading to failures in instruction emulation.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQEcBAABCAAGBQJbfVFcAAoJEJ2a6ncsY3GfwAcH/i4BDNm5bSXLbCZv1Zqc9iWM
ZqCNSlx9fuR5z+Bl3FWvm14CqfG7JFMd1pVXVD3AEGN6nv0mtLPotmoaw+BUWXIP
aD3BRIBSfOVHj90CiWJ1pqZGzE49vAKrjUGocuqHhBiqGjYmnnE7QKgD+lQ13SND
LWDV3XaQgoO9+NZdqtV6hsWMmKCmXWIHykkG9H+EVkD+341e2EBQf6r83qibAGz4
U5SHkr/3JqL8oC7RJixT8CS/dV5qCgmuL8Vs5NYDTUnc6DmKhdes2s7OiugK7nHg
twKe8K0aRVowmTA8yIwEN22OeH1FAUmYDClkgHozHFWyD2+u7O9kLrAYZxEN9Q4=
=61nR
-----END PGP SIGNATURE-----
Merge tag 'kvm-ppc-fixes-4.19-1' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc
PPC KVM fixes for 4.19
Two small fixes for KVM on POWER machines; one fixes a bug where pages
might not get marked dirty, causing guest memory corruption on migration,
and the other fixes a bug causing reads from guest memory to use the
wrong guest real address for very large HPT guests (>256G of memory),
leading to failures in instruction emulation.
The newly added code that emits ksymtab entries as pairs of 32-bit
relative references interacts poorly with the way powerpc lays out its
address space: when a module exports a per-CPU variable, the primary
module region covering the ksymtab entry -and thus the 32-bit relative
reference- is too far away from the actual per-CPU variable's base
address (to which the per-CPU offsets are applied to obtain the
respective address of each CPU's copy), resulting in corruption when the
module loader attempts to resolve symbol references of modules that are
loaded on top and link to the exported per-CPU symbol.
So let's disable this feature on powerpc. Even though it implements
CONFIG_RELOCATABLE, it does not implement CONFIG_RANDOMIZE_BASE and so
KASLR kernels (which are the main target of the feature) do not exist on
powerpc anyway.
Reported-by: Andreas Schwab <schwab@linux-m68k.org>
Suggested-by: Nicholas Piggin <nicholas.piggin@gmail.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull IDA updates from Matthew Wilcox:
"A better IDA API:
id = ida_alloc(ida, GFP_xxx);
ida_free(ida, id);
rather than the cumbersome ida_simple_get(), ida_simple_remove().
The new IDA API is similar to ida_simple_get() but better named. The
internal restructuring of the IDA code removes the bitmap
preallocation nonsense.
I hope the net -200 lines of code is convincing"
* 'ida-4.19' of git://git.infradead.org/users/willy/linux-dax: (29 commits)
ida: Change ida_get_new_above to return the id
ida: Remove old API
test_ida: check_ida_destroy and check_ida_alloc
test_ida: Convert check_ida_conv to new API
test_ida: Move ida_check_max
test_ida: Move ida_check_leaf
idr-test: Convert ida_check_nomem to new API
ida: Start new test_ida module
target/iscsi: Allocate session IDs from an IDA
iscsi target: fix session creation failure handling
drm/vmwgfx: Convert to new IDA API
dmaengine: Convert to new IDA API
ppc: Convert vas ID allocation to new IDA API
media: Convert entity ID allocation to new IDA API
ppc: Convert mmu context allocation to new IDA API
Convert net_namespace to new IDA API
cb710: Convert to new IDA API
rsxx: Convert to new IDA API
osd: Convert to new IDA API
sd: Convert to new IDA API
...
- add build_{menu,n,g,x}config targets for compile-testing Kconfig
- fix and improve recursive dependency detection in Kconfig
- fix parallel building of menuconfig/nconfig
- fix syntax error in clang-version.sh
- suppress distracting log from syncconfig
- remove obsolete "rpm" target
- remove VMLINUX_SYMBOL(_STR) macro entirely
- fix microblaze build with CONFIG_DYNAMIC_FTRACE
- move compiler test for dead code/data elimination to Kconfig
- rename well-known LDFLAGS variable to KBUILD_LDFLAGS
- misc fixes and cleanups
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Vsb2
-----END PGP SIGNATURE-----
Merge tag 'kbuild-v4.19-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull more Kbuild updates from Masahiro Yamada:
- add build_{menu,n,g,x}config targets for compile-testing Kconfig
- fix and improve recursive dependency detection in Kconfig
- fix parallel building of menuconfig/nconfig
- fix syntax error in clang-version.sh
- suppress distracting log from syncconfig
- remove obsolete "rpm" target
- remove VMLINUX_SYMBOL(_STR) macro entirely
- fix microblaze build with CONFIG_DYNAMIC_FTRACE
- move compiler test for dead code/data elimination to Kconfig
- rename well-known LDFLAGS variable to KBUILD_LDFLAGS
- misc fixes and cleanups
* tag 'kbuild-v4.19-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
kbuild: rename LDFLAGS to KBUILD_LDFLAGS
kbuild: pass LDFLAGS to recordmcount.pl
kbuild: test dead code/data elimination support in Kconfig
initramfs: move gen_initramfs_list.sh from scripts/ to usr/
vmlinux.lds.h: remove stale <linux/export.h> include
export.h: remove VMLINUX_SYMBOL() and VMLINUX_SYMBOL_STR()
Coccinelle: remove pci_alloc_consistent semantic to detect in zalloc-simple.cocci
kbuild: make sorting initramfs contents independent of locale
kbuild: remove "rpm" target, which is alias of "rpm-pkg"
kbuild: Fix LOADLIBES rename in Documentation/kbuild/makefiles.txt
kconfig: suppress "configuration written to .config" for syncconfig
kconfig: fix "Can't open ..." in parallel build
kbuild: Add a space after `!` to prevent parsing as file pattern
scripts: modpost: check memory allocation results
kconfig: improve the recursive dependency report
kconfig: report recursive dependency involving 'imply'
kconfig: error out when seeing recursive dependency
kconfig: add build-only configurator targets
scripts/dtc: consolidate include path options in Makefile
- An implementation for the newly added hv_ops->flush() for the OPAL hvc
console driver backends, I forgot to apply this after merging the hvc driver
changes before the merge window.
- Enable all PCI bridges at boot on powernv, to avoid races when multiple
children of a bridge try to enable it simultaneously. This is a workaround
until the PCI core can be enhanced to fix the races.
- A fix to query PowerVM for the correct system topology at boot before
initialising sched domains, seen in some configurations to cause broken
scheduling etc.
- A fix for pte_access_permitted() on "nohash" platforms.
- Two commits to fix SIGBUS when using remap_pfn_range() seen on Power9 due to
a workaround when using the nest MMU (GPUs, accelerators).
- Another fix to the VFIO code used by KVM, the previous fix had some bugs
which caused guests to not start in some configurations.
- A handful of other minor fixes.
Thanks to:
Aneesh Kumar K.V, Benjamin Herrenschmidt, Christophe Leroy, Hari Bathini, Luke
Dashjr, Mahesh Salgaonkar, Nicholas Piggin, Paul Mackerras, Srikar Dronamraju.
-----BEGIN PGP SIGNATURE-----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=1AUa
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.19-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
- An implementation for the newly added hv_ops->flush() for the OPAL
hvc console driver backends, I forgot to apply this after merging the
hvc driver changes before the merge window.
- Enable all PCI bridges at boot on powernv, to avoid races when
multiple children of a bridge try to enable it simultaneously. This
is a workaround until the PCI core can be enhanced to fix the races.
- A fix to query PowerVM for the correct system topology at boot before
initialising sched domains, seen in some configurations to cause
broken scheduling etc.
- A fix for pte_access_permitted() on "nohash" platforms.
- Two commits to fix SIGBUS when using remap_pfn_range() seen on Power9
due to a workaround when using the nest MMU (GPUs, accelerators).
- Another fix to the VFIO code used by KVM, the previous fix had some
bugs which caused guests to not start in some configurations.
- A handful of other minor fixes.
Thanks to: Aneesh Kumar K.V, Benjamin Herrenschmidt, Christophe Leroy,
Hari Bathini, Luke Dashjr, Mahesh Salgaonkar, Nicholas Piggin, Paul
Mackerras, Srikar Dronamraju.
* tag 'powerpc-4.19-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/mce: Fix SLB rebolting during MCE recovery path.
KVM: PPC: Book3S: Fix guest DMA when guest partially backed by THP pages
powerpc/mm/radix: Only need the Nest MMU workaround for R -> RW transition
powerpc/mm/books3s: Add new pte bit to mark pte temporarily invalid.
powerpc/nohash: fix pte_access_permitted()
powerpc/topology: Get topology for shared processors at boot
powerpc64/ftrace: Include ftrace.h needed for enable/disable calls
powerpc/powernv/pci: Work around races in PCI bridge enabling
powerpc/fadump: cleanup crash memory ranges support
powerpc/powernv: provide a console flush operation for opal hvc driver
powerpc/traps: Avoid rate limit messages from show unhandled signals
powerpc/64s: Fix PACA_IRQ_HARD_DIS accounting in idle_power4()
Also add these typos to spelling.txt so checkpatch.pl will look for them.
Link: http://lkml.kernel.org/r/88af06b9de34d870cb0afc46cfd24e0458be2575.1529471371.git.fthain@telegraphics.com.au
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Joe Perches <joe@perches.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit a0f97e06a4 ("kbuild: enable 'make CFLAGS=...' to add
additional options to CC") renamed CFLAGS to KBUILD_CFLAGS.
Commit 222d394d30 ("kbuild: enable 'make AFLAGS=...' to add
additional options to AS") renamed AFLAGS to KBUILD_AFLAGS.
Commit 06c5040cdb ("kbuild: enable 'make CPPFLAGS=...' to add
additional options to CPP") renamed CPPFLAGS to KBUILD_CPPFLAGS.
For some reason, LDFLAGS was not renamed.
Using a well-known variable like LDFLAGS may result in accidental
override of the variable.
Kbuild generally uses KBUILD_ prefixed variables for the internally
appended options, so here is one more conversion to sanitize the
naming convention.
I did not touch Makefiles under tools/ since the tools build system
is a different world.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Reviewed-by: Palmer Dabbelt <palmer@sifive.com>
The commit e7e8184747 ("powerpc/64s: move machine check SLB flushing
to mm/slb.c") introduced a bug in reloading bolted SLB entries. Unused
bolted entries are stored with .esid=0 in the slb_shadow area, and
that value is now used directly as the RB input to slbmte, which means
the RB[52:63] index field is set to 0, which causes SLB entry 0 to be
cleared.
Fix this by storing the index bits in the unused bolted entries, which
directs the slbmte to the right place.
The SLB shadow area is also used by the hypervisor, but PAPR is okay
with that, from LoPAPR v1.1, 14.11.1.3 SLB Shadow Buffer:
Note: SLB is filled sequentially starting at index 0
from the shadow buffer ignoring the contents of
RB field bits 52-63
Fixes: e7e8184747 ("powerpc/64s: move machine check SLB flushing to mm/slb.c")
Signed-off-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Commit 76fa4975f3 ("KVM: PPC: Check if IOMMU page is contained in
the pinned physical page", 2018-07-17) added some checks to ensure
that guest DMA mappings don't attempt to map more than the guest is
entitled to access. However, errors in the logic mean that legitimate
guest requests to map pages for DMA are being denied in some
situations. Specifically, if the first page of the range passed to
mm_iommu_get() is mapped with a normal page, and subsequent pages are
mapped with transparent huge pages, we end up with mem->pageshift ==
0. That means that the page size checks in mm_iommu_ua_to_hpa() and
mm_iommu_up_to_hpa_rm() will always fail for every page in that
region, and thus the guest can never map any memory in that region for
DMA, typically leading to a flood of error messages like this:
qemu-system-ppc64: VFIO_MAP_DMA: -22
qemu-system-ppc64: vfio_dma_map(0x10005f47780, 0x800000000000000, 0x10000, 0x7fff63ff0000) = -22 (Invalid argument)
The logic errors in mm_iommu_get() are:
(a) use of 'ua' not 'ua + (i << PAGE_SHIFT)' in the find_linux_pte()
call (meaning that find_linux_pte() returns the pte for the
first address in the range, not the address we are currently up
to);
(b) use of 'pageshift' as the variable to receive the hugepage shift
returned by find_linux_pte() - for a normal page this gets set
to 0, leading to us setting mem->pageshift to 0 when we conclude
that the pte returned by find_linux_pte() didn't match the page
we were looking at;
(c) comparing 'compshift', which is a page order, i.e. log base 2 of
the number of pages, with 'pageshift', which is a log base 2 of
the number of bytes.
To fix these problems, this patch introduces 'cur_ua' to hold the
current user address and uses that in the find_linux_pte() call;
introduces 'pteshift' to hold the hugepage shift found by
find_linux_pte(); and compares 'pteshift' with 'compshift +
PAGE_SHIFT' rather than 'compshift'.
The patch also moves the local_irq_restore to the point after the PTE
pointer returned by find_linux_pte() has been dereferenced because
otherwise the PTE could change underneath us, and adds a check to
avoid doing the find_linux_pte() call once mem->pageshift has been
reduced to PAGE_SHIFT, as an optimization.
Fixes: 76fa4975f3 ("KVM: PPC: Check if IOMMU page is contained in the pinned physical page")
Cc: stable@vger.kernel.org # v4.12+
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The Nest MMU workaround is only needed for RW upgrades. Avoid doing
that for other PTE updates.
We also avoid clearing the PTE while marking it invalid. This is
because other page table walkers will find this PTE none and can
result in unexpected behaviour due to that. Instead we clear
_PAGE_PRESENT and set the software PTE bit _PAGE_INVALID.
pte_present() is already updated to check for both bits. This makes
sure page table walkers will find the PTE present and things like
pte_pfn(pte) returns the right value.
Based on an original patch from Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
When splitting a huge pmd pte, we need to mark the pmd entry invalid. We
can do that by clearing _PAGE_PRESENT bit. But then that will be taken as a
swap pte. In order to differentiate between the two use a software pte bit
when invalidating.
For regular pte, due to bd5050e38a ("powerpc/mm/radix: Change pte relax
sequence to handle nest MMU hang") we need to mark the pte entry invalid when
relaxing access permission. Instead of marking pte_none which can result in
different page table walk routines possibly skipping this pte entry, invalidate
it but still keep it marked present.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Commit 5769beaf18 ("powerpc/mm: Add proper pte access check helper
for other platforms") replaced generic pte_access_permitted() by an
arch specific one.
The generic one is defined as
(pte_present(pte) && (!(write) || pte_write(pte)))
The arch specific one is open coded checking that _PAGE_USER and
_PAGE_WRITE (_PAGE_RW) flags are set, but lacking to check that
_PAGE_RO and _PAGE_PRIVILEGED are unset, leading to a useless test
on targets like the 8xx which defines _PAGE_RW and _PAGE_USER as 0.
Commit 5fa5b16be5 ("powerpc/mm/hugetlb: Use pte_access_permitted
for hugetlb access check") replaced some tests performed with
pte helpers by a call to pte_access_permitted(), leading to the same
issue.
This patch rewrites powerpc/nohash pte_access_permitted()
using pte helpers.
Fixes: 5769beaf18 ("powerpc/mm: Add proper pte access check helper for other platforms")
Fixes: 5fa5b16be5 ("powerpc/mm/hugetlb: Use pte_access_permitted for hugetlb access check")
Cc: stable@vger.kernel.org # v4.15+
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Reviewed-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Patch series "add support for relative references in special sections", v10.
This adds support for emitting special sections such as initcall arrays,
PCI fixups and tracepoints as relative references rather than absolute
references. This reduces the size by 50% on 64-bit architectures, but
more importantly, it removes the need for carrying relocation metadata for
these sections in relocatable kernels (e.g., for KASLR) that needs to be
fixed up at boot time. On arm64, this reduces the vmlinux footprint of
such a reference by 8x (8 byte absolute reference + 24 byte RELA entry vs
4 byte relative reference)
Patch #3 was sent out before as a single patch. This series supersedes
the previous submission. This version makes relative ksymtab entries
dependent on the new Kconfig symbol HAVE_ARCH_PREL32_RELOCATIONS rather
than trying to infer from kbuild test robot replies for which
architectures it should be blacklisted.
Patch #1 introduces the new Kconfig symbol HAVE_ARCH_PREL32_RELOCATIONS,
and sets it for the main architectures that are expected to benefit the
most from this feature, i.e., 64-bit architectures or ones that use
runtime relocations.
Patch #2 add support for #define'ing __DISABLE_EXPORTS to get rid of
ksymtab/kcrctab sections in decompressor and EFI stub objects when
rebuilding existing C files to run in a different context.
Patches #4 - #6 implement relative references for initcalls, PCI fixups
and tracepoints, respectively, all of which produce sections with order
~1000 entries on an arm64 defconfig kernel with tracing enabled. This
means we save about 28 KB of vmlinux space for each of these patches.
[From the v7 series blurb, which included the jump_label patches as well]:
For the arm64 kernel, all patches combined reduce the memory footprint
of vmlinux by about 1.3 MB (using a config copied from Ubuntu that has
KASLR enabled), of which ~1 MB is the size reduction of the RELA section
in .init, and the remaining 300 KB is reduction of .text/.data.
This patch (of 6):
Before updating certain subsystems to use place relative 32-bit
relocations in special sections, to save space and reduce the number of
absolute relocations that need to be processed at runtime by relocatable
kernels, introduce the Kconfig symbol and define it for some architectures
that should be able to support and benefit from it.
Link: http://lkml.kernel.org/r/20180704083651.24360-2-ard.biesheuvel@linaro.org
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Acked-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Will Deacon <will.deacon@arm.com>
Acked-by: Ingo Molnar <mingo@kernel.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Kees Cook <keescook@chromium.org>
Cc: Thomas Garnier <thgarnie@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "Serge E. Hallyn" <serge@hallyn.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Petr Mladek <pmladek@suse.com>
Cc: James Morris <jmorris@namei.org>
Cc: Nicolas Pitre <nico@linaro.org>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>,
Cc: James Morris <james.morris@microsoft.com>
Cc: Jessica Yu <jeyu@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Removes a custom spinlock and simplifies the code. Also fix an
error where we could allocate one ID too many.
Signed-off-by: Matthew Wilcox <willy@infradead.org>
ida_alloc_range is the perfect fit for this use case. Eliminates
a custom spinlock, a call to ida_pre_get and a local check for the
allocated ID exceeding a maximum.
Signed-off-by: Matthew Wilcox <willy@infradead.org>
Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
On a shared LPAR, Phyp will not update the CPU associativity at boot
time. Just after the boot system does recognize itself as a shared
LPAR and trigger a request for correct CPU associativity. But by then
the scheduler would have already created/destroyed its sched domains.
This causes
- Broken load balance across Nodes causing islands of cores.
- Performance degradation esp if the system is lightly loaded
- dmesg to wrongly report all CPUs to be in Node 0.
- Messages in dmesg saying borken topology.
- With commit 051f3ca02e ("sched/topology: Introduce NUMA identity
node sched domain"), can cause rcu stalls at boot up.
The sched_domains_numa_masks table which is used to generate cpumasks
is only created at boot time just before creating sched domains and
never updated. Hence, its better to get the topology correct before
the sched domains are created.
For example on 64 core Power 8 shared LPAR, dmesg reports
Brought up 512 CPUs
Node 0 CPUs: 0-511
Node 1 CPUs:
Node 2 CPUs:
Node 3 CPUs:
Node 4 CPUs:
Node 5 CPUs:
Node 6 CPUs:
Node 7 CPUs:
Node 8 CPUs:
Node 9 CPUs:
Node 10 CPUs:
Node 11 CPUs:
...
BUG: arch topology borken
the DIE domain not a subset of the NUMA domain
BUG: arch topology borken
the DIE domain not a subset of the NUMA domain
numactl/lscpu output will still be correct with cores spreading across
all nodes:
Socket(s): 64
NUMA node(s): 12
Model: 2.0 (pvr 004d 0200)
Model name: POWER8 (architected), altivec supported
Hypervisor vendor: pHyp
Virtualization type: para
L1d cache: 64K
L1i cache: 32K
NUMA node0 CPU(s): 0-7,32-39,64-71,96-103,176-183,272-279,368-375,464-471
NUMA node1 CPU(s): 8-15,40-47,72-79,104-111,184-191,280-287,376-383,472-479
NUMA node2 CPU(s): 16-23,48-55,80-87,112-119,192-199,288-295,384-391,480-487
NUMA node3 CPU(s): 24-31,56-63,88-95,120-127,200-207,296-303,392-399,488-495
NUMA node4 CPU(s): 208-215,304-311,400-407,496-503
NUMA node5 CPU(s): 168-175,264-271,360-367,456-463
NUMA node6 CPU(s): 128-135,224-231,320-327,416-423
NUMA node7 CPU(s): 136-143,232-239,328-335,424-431
NUMA node8 CPU(s): 216-223,312-319,408-415,504-511
NUMA node9 CPU(s): 144-151,240-247,336-343,432-439
NUMA node10 CPU(s): 152-159,248-255,344-351,440-447
NUMA node11 CPU(s): 160-167,256-263,352-359,448-455
Currently on this LPAR, the scheduler detects 2 levels of Numa and
created numa sched domains for all CPUs, but it finds a single DIE
domain consisting of all CPUs. Hence it deletes all numa sched
domains.
To address this, detect the shared processor and update topology soon
after CPUs are setup so that correct topology is updated just before
scheduler creates sched domain.
With the fix, dmesg reports:
numa: Node 0 CPUs: 0-7 32-39 64-71 96-103 176-183 272-279 368-375 464-471
numa: Node 1 CPUs: 8-15 40-47 72-79 104-111 184-191 280-287 376-383 472-479
numa: Node 2 CPUs: 16-23 48-55 80-87 112-119 192-199 288-295 384-391 480-487
numa: Node 3 CPUs: 24-31 56-63 88-95 120-127 200-207 296-303 392-399 488-495
numa: Node 4 CPUs: 208-215 304-311 400-407 496-503
numa: Node 5 CPUs: 168-175 264-271 360-367 456-463
numa: Node 6 CPUs: 128-135 224-231 320-327 416-423
numa: Node 7 CPUs: 136-143 232-239 328-335 424-431
numa: Node 8 CPUs: 216-223 312-319 408-415 504-511
numa: Node 9 CPUs: 144-151 240-247 336-343 432-439
numa: Node 10 CPUs: 152-159 248-255 344-351 440-447
numa: Node 11 CPUs: 160-167 256-263 352-359 448-455
and lscpu also reports:
Socket(s): 64
NUMA node(s): 12
Model: 2.0 (pvr 004d 0200)
Model name: POWER8 (architected), altivec supported
Hypervisor vendor: pHyp
Virtualization type: para
L1d cache: 64K
L1i cache: 32K
NUMA node0 CPU(s): 0-7,32-39,64-71,96-103,176-183,272-279,368-375,464-471
NUMA node1 CPU(s): 8-15,40-47,72-79,104-111,184-191,280-287,376-383,472-479
NUMA node2 CPU(s): 16-23,48-55,80-87,112-119,192-199,288-295,384-391,480-487
NUMA node3 CPU(s): 24-31,56-63,88-95,120-127,200-207,296-303,392-399,488-495
NUMA node4 CPU(s): 208-215,304-311,400-407,496-503
NUMA node5 CPU(s): 168-175,264-271,360-367,456-463
NUMA node6 CPU(s): 128-135,224-231,320-327,416-423
NUMA node7 CPU(s): 136-143,232-239,328-335,424-431
NUMA node8 CPU(s): 216-223,312-319,408-415,504-511
NUMA node9 CPU(s): 144-151,240-247,336-343,432-439
NUMA node10 CPU(s): 152-159,248-255,344-351,440-447
NUMA node11 CPU(s): 160-167,256-263,352-359,448-455
Reported-by: Manjunatha H R <manjuhr1@in.ibm.com>
Signed-off-by: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
[mpe: Trim / format change log]
Tested-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
