Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2018-04-24
This series contains fixes to ixgbevf, igb and ice drivers.
Colin Ian King fixes the return value on error for the new XDP support
that went into ixgbevf for 4.17.
Vinicius provides a fix for queue 0 for igb, which was not receiving all
the credits it needed when QAV mode was enabled.
Anirudh provides several fixes for the new ice driver, starting with
properly initializing num_nodes_added to zero. Fixed up a code comment
to better reflect what is really going on in the code. Fixed how to
detect if an OICR interrupt has occurred to a more reliable method.
Md Fahad fixes the ice driver to allocate the right amount of memory
when reading and storing the devices MAC addresses. The device can have
up to 2 MAC addresses (LAN and WoL), while WoL is currently not
supported, we need to ensure it can be properly handled when support is
added.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
For the MAC read operation, the device can return up to two (LAN and WoL)
MAC addresses. Without access to adequate memory, the device will return
an error. Fixed this by allocating the right amount of memory. Also, logic
to detect and copy the LAN MAC address into the port_info structure has
been added. Note that the WoL MAC address is ignored currently as the WoL
feature isn't supported yet.
Fixes: dc49c77236 ("ice: Get MAC/PHY/link info and scheduler topology")
Signed-off-by: Md Fahad Iqbal Polash <md.fahad.iqbal.polash@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Associate an arbitrary ID with each ARFS filter, allowing to properly query
for expiry. The association is maintained in a hash table, which is
protected by a spinlock.
v3: fix build warnings when CONFIG_RFS_ACCEL is disabled (thanks lkp-robot).
v2: fixed uninitialised variable (thanks davem and lkp-robot).
Fixes: 3af0f34290 ("sfc: replace asynchronous filter operations")
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to the hardware spec, checking the INTEVENT bit isn't a
reliable way to detect if an OICR interrupt has occurred. This is
because this bit can be cleared by the hardware/firmware before the
interrupt service routine has run. So instead, just check for OICR
events every time.
Fixes: 940b61af02 ("ice: Initialize PF and setup miscellaneous interrupt")
Signed-off-by: Ben Shelton <benjamin.h.shelton@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Action type 5 defines large action generic values. Fix comment to
reflect that better.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
ice_sched_add_nodes_to_layer is used recursively, and so we start
with num_nodes_added being 0. This way, in case of an error or if
num_nodes is NULL, the function just returns 0 to indicate that no
nodes were added.
Fixes: 5513b920a4 ("ice: Update Tx scheduler tree for VSI multi-Tx queue support")
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When Qav mode is enabled, queue 0 should be kept on Stream Reservation
mode. From the i210 datasheet, section 8.12.19:
"Note: Queue0 QueueMode must be set to 1b when TransmitMode is set to
Qav." ("QueueMode 1b" represents the Stream Reservation mode)
The solution is to give queue 0 the all the credits it might need, so
it has priority over queue 1.
A situation where this can happen is when cbs is "installed" only on
queue 1, leaving queue 0 alone. For example:
$ tc qdisc replace dev enp2s0 handle 100: parent root mqprio num_tc 3 \
map 2 2 1 0 2 2 2 2 2 2 2 2 2 2 2 2 queues 1@0 1@1 2@2 hw 0
$ tc qdisc replace dev enp2s0 parent 100:2 cbs locredit -1470 \
hicredit 30 sendslope -980000 idleslope 20000 offload 1
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The current error handling for failed resource setup for xdp_ring
data is a break out of the loop and returning 0 indicated everything
was OK, when in fact it is not. Fix this by exiting via the
error exit label err_setup_tx that will clean up the resources
correctly and return and error status.
Detected by CoverityScan, CID#1466879 ("Logically dead code")
Fixes: 21092e9ce8 ("ixgbevf: Add support for XDP_TX action")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The SFP eeprom indicates the transceiver signals (Rx LOS, Tx Fault, etc.)
that it supports. Update the driver to include checking the eeprom data
when deciding whether to use a transceiver signal.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update xgbe-phy-v2.c to make use of the auto-negotiation (AN) phy hooks
to improve the ability to successfully complete Clause 73 AN when running
at 10gbps. Hardware can sometimes have issues with CDR lock when the
AN DME page exchange is being performed.
The AN and KR training hooks are used as follows:
- The pre AN hook is used to disable CDR tracking in the PHY so that the
DME page exchange can be successfully and consistently completed.
- The post KR training hook is used to re-enable the CDR tracking so that
KR training can successfully complete.
- The post AN hook is used to check for an unsuccessful AN which will
increase a CDR tracking enablement delay (up to a maximum value).
Add two debugfs entries to allow control over use of the CDR tracking
workaround. The debugfs entries allow the CDR tracking workaround to
be disabled and determine whether to re-enable CDR tracking before or
after link training has been initiated.
Also, with these changes the receiver reset cycle that is performed during
the link status check can be performed less often.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add hooks to the driver auto-negotiation (AN) flow to allow the different
phy implementations to perform any steps necessary to improve AN.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Avoid using value stored in the login response buffer when
cleaning TX and RX buffer pools since these could be inconsistent
depending on the device state. Instead use the field in the driver's
private data that tracks the number of active pools.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The CPDMA_TX_PRIORITY_MAP in real is vlan pcp field priority mapping
register and basically replaces vlan pcp field for tagged packets.
So, set it to be 1:1 mapping. Otherwise, it will cause unexpected
change of egress vlan tagged packets, like prio 2 -> prio 5.
Fixes: e05107e6b7 ("net: ethernet: ti: cpsw: add multi queue support")
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In some firmware images, the length of BNX_DIR_TYPE_PKG_LOG nvram type
could be greater than the fixed buffer length of 4096 bytes allocated by
the driver. This was causing HWRM_NVM_READ to copy more data to the buffer
than the allocated size, causing general protection fault.
Fix the issue by allocating the exact buffer length returned by
HWRM_NVM_FIND_DIR_ENTRY, instead of 4096. Move the kzalloc() call
into the bnxt_get_pkgver() function.
Fixes: 3ebf6f0a09 ("bnxt_en: Add installed-package firmware version reporting via Ethtool GDRVINFO")
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When longer interface names are used, the action names exposed in
/proc/interrupts and /proc/irq/* maybe truncated. For example, when
using the predictable name algorithm in systemd on a HiSilicon D05,
I see:
ubuntu@d05-3:~$ grep enahisic2i0-tx /proc/interrupts | sed 's/.* //'
enahisic2i0-tx0
enahisic2i0-tx1
[...]
enahisic2i0-tx8
enahisic2i0-tx9
enahisic2i0-tx1
enahisic2i0-tx1
enahisic2i0-tx1
enahisic2i0-tx1
enahisic2i0-tx1
enahisic2i0-tx1
Increase the max ring name length to allow for an interface name
of IFNAMSIZE. After this change, I now see:
$ grep enahisic2i0-tx /proc/interrupts | sed 's/.* //'
enahisic2i0-tx0
enahisic2i0-tx1
enahisic2i0-tx2
[...]
enahisic2i0-tx8
enahisic2i0-tx9
enahisic2i0-tx10
enahisic2i0-tx11
enahisic2i0-tx12
enahisic2i0-tx13
enahisic2i0-tx14
enahisic2i0-tx15
Signed-off-by: dann frazier <dann.frazier@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ACS Feature is currently enabled for GMAC >= 4 but the llc_snap status
is never checked in descriptor rx_status callback. This will cause
stmmac to always strip packets even that ACS feature is already
stripping them.
Lets be safe and disable the ACS feature for GMAC >= 4 and always strip
the packets for this GMAC version.
Fixes: 477286b53f ("stmmac: add GMAC4 core support")
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PPv2 TX/RX descriptors uses 40bits DMA addresses, but 41 bits masks were
used (GENMASK_ULL(40, 0)).
This commit fixes that by using the correct mask.
Fixes: e7c5359f2e ("net: mvpp2: introduce PPv2.2 HW descriptors and adapt accessors")
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the last rmnet device attached to a real device is removed, the
real device is unregistered from rmnet. As a result, the real device
lookup fails resulting in a warning when the fill_info handler is
called as part of the rmnet device unregistration.
Fix this by returning the rmnet flags as 0 when no real device is
present.
WARNING: CPU: 0 PID: 1779 at net/core/rtnetlink.c:3254
rtmsg_ifinfo_build_skb+0xca/0x10d
Modules linked in:
CPU: 0 PID: 1779 Comm: ip Not tainted 4.16.0-11872-g7ce2367 #1
Stack:
7fe655f0 60371ea3 00000000 00000000
60282bc6 6006b116 7fe65600 60371ee8
7fe65660 6003a68c 00000000 900000000
Call Trace:
[<6006b116>] ? printk+0x0/0x94
[<6001f375>] show_stack+0xfe/0x158
[<60371ea3>] ? dump_stack_print_info+0xe8/0xf1
[<60282bc6>] ? rtmsg_ifinfo_build_skb+0xca/0x10d
[<6006b116>] ? printk+0x0/0x94
[<60371ee8>] dump_stack+0x2a/0x2c
[<6003a68c>] __warn+0x10e/0x13e
[<6003a82c>] warn_slowpath_null+0x48/0x4f
[<60282bc6>] rtmsg_ifinfo_build_skb+0xca/0x10d
[<60282c4d>] rtmsg_ifinfo_event.part.37+0x1e/0x43
[<60282c2f>] ? rtmsg_ifinfo_event.part.37+0x0/0x43
[<60282d03>] rtmsg_ifinfo+0x24/0x28
[<60264e86>] dev_close_many+0xba/0x119
[<60282cdf>] ? rtmsg_ifinfo+0x0/0x28
[<6027c225>] ? rtnl_is_locked+0x0/0x1c
[<6026ca67>] rollback_registered_many+0x1ae/0x4ae
[<600314be>] ? unblock_signals+0x0/0xae
[<6026cdc0>] ? unregister_netdevice_queue+0x19/0xec
[<6026ceec>] unregister_netdevice_many+0x21/0xa1
[<6027c765>] rtnl_delete_link+0x3e/0x4e
[<60280ecb>] rtnl_dellink+0x262/0x29c
[<6027c241>] ? rtnl_get_link+0x0/0x3e
[<6027f867>] rtnetlink_rcv_msg+0x235/0x274
Fixes: be81a85f5f ("net: qualcomm: rmnet: Implement fill_info")
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
For some firmware variants - specifically 'capture packed stream' - RSS
filters are not valid. We must check if RSS is actually active rather
than merely enabled.
Fixes: 42356d9a13 ("sfc: support RSS spreading of ethtool ntuple filters")
Signed-off-by: Bert Kenward <bkenward@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Due to a firmware bug, the hypervisor can send an interrupt to a
transmit or receive queue just prior to a partition migration, not
allowing the device enough time to handle it and send an EOI. When
the partition migrates, the interrupt is lost but an "EOI-pending"
flag for the interrupt line is still set in firmware. No further
interrupts will be sent until that flag is cleared, effectively
freezing that queue. To workaround this, the driver will disable the
hardware interrupt and send an H_EOI signal prior to re-enabling it.
This will flush the pending EOI and allow the driver to continue
operation.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Marvell's PPv2 controller has a Packet Header parser, which uses a
fixed-size TCAM array of filter entries.
The mvpp2 driver reserves some ranges among the 256 TCAM entries to
perform MAC and VID filtering. The rest of the TCAM ids are freely usable
for other features, such as IPv4 proto matching.
This commit fixes the MVPP2_PE_LAST_FREE_TID define that sets the end of
the "free range", which included the MAC range. This could therefore allow
some other features to use entries dedicated to MAC filtering,
lowering the number of unicast/multicast addresses that could be allowed
before switching to promiscuous mode.
Fixes: 10fea26ce2 ("net: mvpp2: Add support for unicast filtering")
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A misconfigured system (e.g. with all interrupts affinitised to all CPUs)
may produce a storm of ARFS steering events. With the existing sfc ARFS
implementation, that could create a backlog of workitems that grinds the
system to a halt. To prevent this, limit the number of workitems that
may be in flight for a given SFC device to 8 (EFX_RPS_MAX_IN_FLIGHT), and
return EBUSY from our ndo_rx_flow_steer method if the limit is reached.
Given this limit, also store the workitems in an array of slots within the
struct efx_nic, rather than dynamically allocating for each request.
The limit should not negatively impact performance, because it is only
likely to be hit in cases where ARFS will be ineffective anyway.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we inserted an ARFS filter for ndo_rx_flow_steer(), we didn't know
what the filter ID would be, so we just returned 0. Thus, we must also
pass 0 as the filter ID when calling rps_may_expire_flow() for it, and
rely on the flow_id to identify what we're talking about.
Fixes: 3af0f34290 ("sfc: replace asynchronous filter operations")
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Necessary to allow redirecting a flow when the application moves.
Fixes: 3af0f34290 ("sfc: replace asynchronous filter operations")
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce a second skb list for handling control messages and limit the
number of allowed messages. Some control messages are considered more
crucial than others, resulting in the need for a second skb list. By
splitting the list into a separate high and low priority list we can
ensure that messages on the high list get added to the head of the list
that gets processed, this however has no functional impact. Previously
there was no limit on the number of messages allowed on the queue, this
could result in the queue growing boundlessly and eventually the host
running out of memory.
Fixes: b985f870a5 ("nfp: process control messages in workqueue in flower app")
Signed-off-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously we processed the route ack control messages in the workqueue,
this unnecessarily loads the workqueue. We can deal with these messages
sooner as we know we are going to drop them.
Fixes: 8e6a9046b6 ("nfp: flower vxlan neighbour offload")
Signed-off-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When waiting for an NFP mutex is interrupted print a message
to make root causing later error messages easier.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We currently allow signals to interrupt the wait for management FW
commands. Exiting the wait should not cause trouble, the FW will
just finish executing the command in the background and new commands
will wait for the old one to finish.
However, this may not be what users expect (Ctrl-C not actually stopping
the command). Moreover some systems routinely request link information
with signals pending (Ubuntu 14.04 runs a landscape-sysinfo python tool
from MOTD) worrying users with errors like these:
nfp 0000:04:00.0: nfp_nsp: Error -512 waiting for code 0x0007 to start
nfp 0000:04:00.0: nfp: reading port table failed -512
Make the wait for management FW responses non-interruptible.
Fixes: 1a64821c6a ("nfp: add support for service processor access")
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When attempting to change the driver parameters, such as the MTU
value or number of queues, do not call netdev_notify_peers().
Doing so will deadlock on the rtnl_lock.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a bug in handling the possible return codes from sending the
login CRQ. The current code treats any non-success return value,
minus failure to send the crq and a timeout waiting for a login response,
as a need to re-send the login CRQ. This can put the drive in an
infinite loop of trying to login when getting return values other
that a partial success such as a return code of aborted. For these
scenarios the login will not ever succeed at this point and the
driver would need to be reset again.
To resolve this loop trying to login is updated to only retry the
login if the driver gets a return code of a partial success. Other
return codes are treated as an error and the driver returns an error
from ibmvnic_login().
To avoid infinite looping in the partial success return cases, the
number of retries is capped at the maximum number of supported
queues. This value was chosen because the driver does a renegotiation
of capabilities which sets the number of queues possible and allows
the driver to attempt a login for possible value for the number
of queues supported.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The "name" field of struct vnic_login_client_data is a char array of
undefined length. This should be written as "char name[]" so the compiler
can make better decisions about the field (for example, not assuming
it's a single character). This was noticed while trying to tighten the
CONFIG_FORTIFY_SOURCE checking.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) In ip_gre tunnel, handle the conflict between TUNNEL_{SEQ,CSUM} and
GSO/LLTX properly. From Sabrina Dubroca.
2) Stop properly on error in lan78xx_read_otp(), from Phil Elwell.
3) Don't uncompress in slip before rstate is initialized, from Tejaswi
Tanikella.
4) When using 1.x firmware on aquantia, issue a deinit before we
hardware reset the chip, otherwise we break dirty wake WOL. From
Igor Russkikh.
5) Correct log check in vhost_vq_access_ok(), from Stefan Hajnoczi.
6) Fix ethtool -x crashes in bnxt_en, from Michael Chan.
7) Fix races in l2tp tunnel creation and duplicate tunnel detection,
from Guillaume Nault.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (22 commits)
l2tp: fix race in duplicate tunnel detection
l2tp: fix races in tunnel creation
tun: send netlink notification when the device is modified
tun: set the flags before registering the netdevice
lan78xx: Don't reset the interface on open
bnxt_en: Fix NULL pointer dereference at bnxt_free_irq().
bnxt_en: Need to include RDMA rings in bnxt_check_rings().
bnxt_en: Support max-mtu with VF-reps
bnxt_en: Ignore src port field in decap filter nodes
bnxt_en: do not allow wildcard matches for L2 flows
bnxt_en: Fix ethtool -x crash when device is down.
vhost: return bool from *_access_ok() functions
vhost: fix vhost_vq_access_ok() log check
vhost: Fix vhost_copy_to_user()
net: aquantia: oops when shutdown on already stopped device
net: aquantia: Regression on reset with 1.x firmware
cdc_ether: flag the Cinterion AHS8 modem by gemalto as WWAN
slip: Check if rstate is initialized before uncompressing
lan78xx: Avoid spurious kevent 4 "error"
lan78xx: Correctly indicate invalid OTP
...
- Rework the idle loop in order to prevent CPUs from spending too
much time in shallow idle states by making it stop the scheduler
tick before putting the CPU into an idle state only if the idle
duration predicted by the idle governor is long enough. That
required the code to be reordered to invoke the idle governor
before stopping the tick, among other things (Rafael Wysocki,
Frederic Weisbecker, Arnd Bergmann).
- Add the missing description of the residency sysfs attribute to
the cpuidle documentation (Prashanth Prakash).
- Finalize the cpufreq cleanup moving frequency table validation
from drivers to the core (Viresh Kumar).
- Fix a clock leak regression in the armada-37xx cpufreq driver
(Gregory Clement).
- Fix the initialization of the CPU performance data structures
for shared policies in the CPPC cpufreq driver (Shunyong Yang).
- Clean up the ti-cpufreq, intel_pstate and CPPC cpufreq drivers
a bit (Viresh Kumar, Rafael Wysocki).
- Mark the expected switch fall-throughs in the PM QoS core (Gustavo
Silva).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=Pnk4
-----END PGP SIGNATURE-----
Merge tag 'pm-4.17-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more power management updates from Rafael Wysocki:
"These include one big-ticket item which is the rework of the idle loop
in order to prevent CPUs from spending too much time in shallow idle
states. It reduces idle power on some systems by 10% or more and may
improve performance of workloads in which the idle loop overhead
matters. This has been in the works for several weeks and it has been
tested and reviewed quite thoroughly.
Also included are changes that finalize the cpufreq cleanup moving
frequency table validation from drivers to the core, a few fixes and
cleanups of cpufreq drivers, a cpuidle documentation update and a PM
QoS core update to mark the expected switch fall-throughs in it.
Specifics:
- Rework the idle loop in order to prevent CPUs from spending too
much time in shallow idle states by making it stop the scheduler
tick before putting the CPU into an idle state only if the idle
duration predicted by the idle governor is long enough.
That required the code to be reordered to invoke the idle governor
before stopping the tick, among other things (Rafael Wysocki,
Frederic Weisbecker, Arnd Bergmann).
- Add the missing description of the residency sysfs attribute to the
cpuidle documentation (Prashanth Prakash).
- Finalize the cpufreq cleanup moving frequency table validation from
drivers to the core (Viresh Kumar).
- Fix a clock leak regression in the armada-37xx cpufreq driver
(Gregory Clement).
- Fix the initialization of the CPU performance data structures for
shared policies in the CPPC cpufreq driver (Shunyong Yang).
- Clean up the ti-cpufreq, intel_pstate and CPPC cpufreq drivers a
bit (Viresh Kumar, Rafael Wysocki).
- Mark the expected switch fall-throughs in the PM QoS core (Gustavo
Silva)"
* tag 'pm-4.17-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (23 commits)
tick-sched: avoid a maybe-uninitialized warning
cpufreq: Drop cpufreq_table_validate_and_show()
cpufreq: SCMI: Don't validate the frequency table twice
cpufreq: CPPC: Initialize shared perf capabilities of CPUs
cpufreq: armada-37xx: Fix clock leak
cpufreq: CPPC: Don't set transition_latency
cpufreq: ti-cpufreq: Use builtin_platform_driver()
cpufreq: intel_pstate: Do not include debugfs.h
PM / QoS: mark expected switch fall-throughs
cpuidle: Add definition of residency to sysfs documentation
time: hrtimer: Use timerqueue_iterate_next() to get to the next timer
nohz: Avoid duplication of code related to got_idle_tick
nohz: Gather tick_sched booleans under a common flag field
cpuidle: menu: Avoid selecting shallow states with stopped tick
cpuidle: menu: Refine idle state selection for running tick
sched: idle: Select idle state before stopping the tick
time: hrtimer: Introduce hrtimer_next_event_without()
time: tick-sched: Split tick_nohz_stop_sched_tick()
cpuidle: Return nohz hint from cpuidle_select()
jiffies: Introduce USER_TICK_USEC and redefine TICK_USEC
...
When open fails during ethtool -L ring change, for example, the driver
may crash at bnxt_free_irq() because bp->bnapi is NULL.
If we fail to allocate all the new rings, bnxt_open_nic() will free
all the memory including bp->bnapi. Subsequent call to bnxt_close_nic()
will try to dereference bp->bnapi in bnxt_free_irq().
Fix it by checking for !bp->bnapi in bnxt_free_irq().
Fixes: e5811b8c09 ("bnxt_en: Add IRQ remapping logic.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With recent changes to reserve both L2 and RDMA rings, we need to include
the RDMA rings in bnxt_check_rings(). Otherwise we will under-estimate
the rings we need during ethtool -L and may lead to failure.
Fixes: fbcfc8e467 ("bnxt_en: Reserve completion rings and MSIX for bnxt_re RDMA driver.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While a VF is configured with a bigger mtu (> 1500), any packets that
are punted to the VF-rep (slow-path) get dropped by OVS kernel-datapath
with the following message: "dropped over-mtu packet". Fix this by
returning the max-mtu value for a VF-rep derived from its corresponding VF.
VF-rep's mtu can be changed using 'ip' command as shown in this example:
$ ip link set bnxt0_pf0vf0 mtu 9000
Signed-off-by: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver currently uses src port field (along with other fields) in the
decap tunnel key, while looking up and adding tunnel nodes. This leads to
redundant cfa_decap_filter_alloc() requests to the FW and flow-miss in the
flow engine. Fix this by ignoring the src port field in decap tunnel nodes.
Fixes: f484f6782e ("bnxt_en: add hwrm FW cmds for cfa_encap_record and decap_filter")
Signed-off-by: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before this patch the following commands would succeed as far as the
user was concerned:
$ tc qdisc add dev p1p1 ingress
$ tc filter add dev p1p1 parent ffff: protocol all \
flower skip_sw action drop
$ tc filter add dev p1p1 parent ffff: protocol ipv4 \
flower skip_sw src_mac 00:02:00:00:00:01/44 action drop
The current flow offload infrastructure used does not support wildcard
matching for ethernet headers, so do not allow the second or third
commands to succeed. If a user wants to drop traffic on that interface
the protocol and MAC addresses need to be specified explicitly:
$ tc qdisc add dev p1p1 ingress
$ tc filter add dev p1p1 parent ffff: protocol arp \
flower skip_sw action drop
$ tc filter add dev p1p1 parent ffff: protocol ipv4 \
flower skip_sw action drop
...
$ tc filter add dev p1p1 parent ffff: protocol ipv4 \
flower skip_sw src_mac 00:02:00:00:00:01 action drop
$ tc filter add dev p1p1 parent ffff: protocol ipv4 \
flower skip_sw src_mac 00:02:00:00:00:02 action drop
...
There are also checks for VLAN parameters in this patch as other callers
may wildcard those parameters even if tc does not. Using different
flow infrastructure could allow this to work in the future for L2 flows,
but for now it does not.
Fixes: 2ae7408fed ("bnxt_en: bnxt: add TC flower filter offload support")
Signed-off-by: Andy Gospodarek <gospo@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix ethtool .get_rxfh() crash by checking for valid indirection table
address before copying the data.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case netdev is closed at the moment of pci shutdown, aq_nic_stop
gets called second time. napi_disable in that case hangs indefinitely.
In other case, if device was never opened at all, we get oops because
of null pointer access.
We should invoke aq_nic_stop conditionally, only if device is running
at the moment of shutdown.
Reported-by: David Arcari <darcari@redhat.com>
Fixes: 90869ddfef ("net: aquantia: Implement pci shutdown callback")
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On ASUS XG-C100C with 1.5.44 firmware a special mode called "dirty wake"
is active. With this mode when motherboard gets powered (but no poweron
happens yet), NIC automatically enables powersave link and watches
for WOL packet.
This normally allows to powerup the PC after AC power failures.
Not all motherboards or bios settings gives power to PCI slots,
so this mode is not enabled on all the hardware.
4.16 linux driver introduced full hardware reset sequence
This is required since before that we had no NIC hardware
reset implemented and there were side effects of "not clean start".
But this full reset is incompatible with "dirty wake" WOL feature
it keeps the PHY link in a special mode forever. As a consequence,
driver sees no link and no traffic.
To fix this we forcibly change FW state to idle state before doing
the full reset. This makes FW to restore link state.
Fixes: c8c82eb net: aquantia: Introduce global AQC hardware reset sequence
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* pm-cpuidle:
tick-sched: avoid a maybe-uninitialized warning
cpuidle: Add definition of residency to sysfs documentation
time: hrtimer: Use timerqueue_iterate_next() to get to the next timer
nohz: Avoid duplication of code related to got_idle_tick
nohz: Gather tick_sched booleans under a common flag field
cpuidle: menu: Avoid selecting shallow states with stopped tick
cpuidle: menu: Refine idle state selection for running tick
sched: idle: Select idle state before stopping the tick
time: hrtimer: Introduce hrtimer_next_event_without()
time: tick-sched: Split tick_nohz_stop_sched_tick()
cpuidle: Return nohz hint from cpuidle_select()
jiffies: Introduce USER_TICK_USEC and redefine TICK_USEC
sched: idle: Do not stop the tick before cpuidle_idle_call()
sched: idle: Do not stop the tick upfront in the idle loop
time: tick-sched: Reorganize idle tick management code
* pm-qos:
PM / QoS: mark expected switch fall-throughs
Pull networking fixes from David Miller:
1) The sockmap code has to free socket memory on close if there is
corked data, from John Fastabend.
2) Tunnel names coming from userspace need to be length validated. From
Eric Dumazet.
3) arp_filter() has to take VRFs properly into account, from Miguel
Fadon Perlines.
4) Fix oops in error path of tcf_bpf_init(), from Davide Caratti.
5) Missing idr_remove() in u32_delete_key(), from Cong Wang.
6) More syzbot stuff. Several use of uninitialized value fixes all
over, from Eric Dumazet.
7) Do not leak kernel memory to userspace in sctp, also from Eric
Dumazet.
8) Discard frames from unused ports in DSA, from Andrew Lunn.
9) Fix DMA mapping and reset/failover problems in ibmvnic, from Thomas
Falcon.
10) Do not access dp83640 PHY registers prematurely after reset, from
Esben Haabendal.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (46 commits)
vhost-net: set packet weight of tx polling to 2 * vq size
net: thunderx: rework mac addresses list to u64 array
inetpeer: fix uninit-value in inet_getpeer
dp83640: Ensure against premature access to PHY registers after reset
devlink: convert occ_get op to separate registration
ARM: dts: ls1021a: Specify TBIPA register address
net/fsl_pq_mdio: Allow explicit speficition of TBIPA address
ibmvnic: Do not reset CRQ for Mobility driver resets
ibmvnic: Fix failover case for non-redundant configuration
ibmvnic: Fix reset scheduler error handling
ibmvnic: Zero used TX descriptor counter on reset
ibmvnic: Fix DMA mapping mistakes
tipc: use the right skb in tipc_sk_fill_sock_diag()
sctp: sctp_sockaddr_af must check minimal addr length for AF_INET6
net: dsa: Discard frames from unused ports
sctp: do not leak kernel memory to user space
soreuseport: initialise timewait reuseport field
ipv4: fix uninit-value in ip_route_output_key_hash_rcu()
dccp: initialize ireq->ir_mark
net: fix uninit-value in __hw_addr_add_ex()
...
It is too expensive to pass u64 values via linked list, instead
allocate array for them by overall number of mac addresses from netdev.
This eventually removes multiple kmalloc() calls, aviod memory
fragmentation and allow to put single null check on kmalloc
return value in order to prevent a potential null pointer dereference.
Addresses-Coverity-ID: 1467429 ("Dereference null return value")
Fixes: 37c3347eb2 ("net: thunderx: add ndo_set_rx_mode callback implementation for VF")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Vadim Lomovtsev <Vadim.Lomovtsev@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This resolves race during initialization where the resources with
ops are registered before driver and the structures used by occ_get
op is initialized. So keep occ_get callbacks registered only when
all structs are initialized.
The example flows, as it is in mlxsw:
1) driver load/asic probe:
mlxsw_core
-> mlxsw_sp_resources_register
-> mlxsw_sp_kvdl_resources_register
-> devlink_resource_register IDX
mlxsw_spectrum
-> mlxsw_sp_kvdl_init
-> mlxsw_sp_kvdl_parts_init
-> mlxsw_sp_kvdl_part_init
-> devlink_resource_size_get IDX (to get the current setup
size from devlink)
-> devlink_resource_occ_get_register IDX (register current
occupancy getter)
2) reload triggered by devlink command:
-> mlxsw_devlink_core_bus_device_reload
-> mlxsw_sp_fini
-> mlxsw_sp_kvdl_fini
-> devlink_resource_occ_get_unregister IDX
(struct mlxsw_sp *mlxsw_sp is freed at this point, call to occ get
which is using mlxsw_sp would cause use-after free)
-> mlxsw_sp_init
-> mlxsw_sp_kvdl_init
-> mlxsw_sp_kvdl_parts_init
-> mlxsw_sp_kvdl_part_init
-> devlink_resource_size_get IDX (to get the current setup
size from devlink)
-> devlink_resource_occ_get_register IDX (register current
occupancy getter)
Fixes: d9f9b9a4d0 ("devlink: Add support for resource abstraction")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This introduces a simpler and generic method for for finding (and mapping)
the TBIPA register.
Instead of relying of complicated logic for finding the TBIPA register
address based on the MDIO or MII register block base
address, which even in some cases relies on undocumented shadow registers,
a second "reg" entry for the mdio bus devicetree node specifies the TBIPA
register.
Backwards compatibility is kept, as the existing logic is applied when
only a single "reg" mapping is specified.
Signed-off-by: Esben Haabendal <eha@deif.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When resetting the ibmvnic driver after a partition migration occurs
there is no requirement to do a reset of the main CRQ. The current
driver code does the required re-enable of the main CRQ, then does
a reset of the main CRQ later.
What we should be doing for a driver reset after a migration is to
re-enable the main CRQ, release all the sub-CRQs, and then allocate
new sub-CRQs after capability negotiation.
This patch updates the handling of mobility resets to do the proper
work and not reset the main CRQ. To do this the initialization/reset
of the main CRQ had to be moved out of the ibmvnic_init routine
and in to the ibmvnic_probe and do_reset routines.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a failover case for a non-redundant pseries VNIC
configuration that was not being handled properly. The current
implementation assumes that the driver will always have a redandant
device to communicate with following a failover notification. There
are cases, however, when a non-redundant configuration can receive
a failover request. If that happens, the driver should wait until
it receives a signal that the device is ready for operation.
The driver is agnostic of its backing hardware configuration,
so this fix necessarily affects all device failover management.
The driver needs to wait until it receives a signal that the device
is ready for resetting. A flag is introduced to track this intermediary
state where the driver is waiting for an active device.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In some cases, if the driver is waiting for a reset following
a device parameter change, failure to schedule a reset can result
in a hang since a completion signal is never sent.
If the device configuration is being altered by a tool such
as ethtool or ifconfig, it could cause the console to hang
if the reset request does not get scheduled. Add some additional
error handling code to exit the wait_for_completion if there is
one in progress.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The counter that tracks used TX descriptors pending completion
needs to be zeroed as part of a device reset. This change fixes
a bug causing transmit queues to be stopped unnecessarily and in
some cases a transmit queue stall and timeout reset. If the counter
is not reset, the remaining descriptors will not be "removed",
effectively reducing queue capacity. If the queue is over half full,
it will cause the queue to stall if stopped.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
