The SOR supports multiple display modes, but only when driving an HDMI
monitor does it make sense to control the +5V power supply. eDP and DP
don't need this, so make it optional.
This fixes a crash observed during system suspend/resume.
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Upon system suspend, make sure the +5V HDMI regulator is disabled. This
avoids potentially leaking current to the HDMI connector. This also
makes sure that upon resume the regulator is enabled again, which in
some cases is necessary to properly restore the state of the supply on
resume.
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Thierry Reding <treding@nvidia.com>
In order to support different modes (DP in addition to HDMI), split out
the audio setup/teardown into callbacks.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The code to enable audio support is split into two parts, one being
generic for the SOR and another part that is specific whether the SOR is
in HDMI mode or in DP mode. Split out the common part in preparation for
reusing the code in DP mode.
Signed-off-by: Thierry Reding <treding@nvidia.com>
When the SOR is disabled in DP mode as part of an unplug event, do not
attempt to power the DP link down. Powering down the link requires the
DPAUX to transmit AUX messages which only works if there's a connected
sink.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The SOR0 on Tegra210 does, contrary to what was previously assumed, in
fact support DisplayPort. The difference between SOR0 and SOR1 is that
the latter supports audio and HDCP over DP, whereas the former doesn't.
The code for eDP and DP is now almost identical and the differences can
easily be parameterized based on the presence of a panel. There is no
need any longer to duplicate the code.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The correct I/O pad needs to be powered up before DP can be used. Make
sure the correct default is set for Tegra generations where the I/O pad
cannot be derived from the SOR instance.
Signed-off-by: Thierry Reding <treding@nvidia.com>
With the clocks modelled consistently across SoC generations, the clock
setup for eDP, HDMI and DP can now be unified.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The connector type detection code is duplicated in two places. Keeping
both places in sync is an extra maintenance burden that can be avoided
by comparing the connector type operations that are set upon the first
detection.
Signed-off-by: Thierry Reding <treding@nvidia.com>
So far the pad clock was only needed on the second SOR instance. The
clock does exist for all SOR instances, though, so make sure it is
always implemented. This prepares for further unification of the code
in subsequent patches.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The device tree bindings for the Tegra210 SOR don't require the
controller instance to be defined, since the instance can be derived
from the compatible string. The index is never used on Tegra210, so we
got away with it not getting set. However, subsequent patches will
change that, so make sure the proper index is used.
Signed-off-by: Thierry Reding <treding@nvidia.com>
It turns out that SOR1 is just another instance of the same block as the
SOR0, so there is no need to distinguish them.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The SOR found on Tegra SoCs does not support all the rates potentially
advertised by eDP 1.4. Make sure that the rates that are not supported
are filtered out.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Rework eDP code to correspond more closely to what's documented. This
also improves the reliability of modesets.
Signed-off-by: Thierry Reding <treding@nvidia.com>
This is necessary for the output abstraction to retrieve a list of valid
modes from the EDID of a connected panel/monitor. This will be useful in
conjunction with DisplayPort support that will be added in a subsequent
patch, so that the driver can read EDID via the AUX channel.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Make use of the DP link training helpers to implement full and fast link
training. While at it, refactor some of the code and remove various code
sequences that are not necessary.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Rather than storing capabilities as flags in an integer, use a separate
boolean per capability. This simplifies the code that checks for these
capabilities.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The hardware is not guaranteed to be enabled during execution of the
tegra_sor_init() function, which can lead to a crash on some Tegra SoCs.
Fix this by moving all register programming into code that is guaranteed
to only be executed when the hardware is enabled.
Signed-off-by: Thierry Reding <treding@nvidia.com>
During the discussion of patches that enhance the drm_dp_link helpers it
was concluded that these helpers aren't very useful to begin with. After
all other drivers have been converted not to use these helpers anymore,
move these helpers into the last remaining user: Tegra DRM.
If at some point these helpers are deemed more widely useful, they can
be moved out into the DRM DP helpers again.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20191021143437.1477719-14-thierry.reding@gmail.com
Drop use of the deprecated drmP.h header file.
For all touched files divide include files into blocks,
and sort them within the blocks.
Fix fallout.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Cc: linux-tegra@vger.kernel.org
Link: https://patchwork.freedesktop.org/patch/msgid/20190804094132.29463-3-sam@ravnborg.org
Based on 2 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation #
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 4122 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Enrico Weigelt <info@metux.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190604081206.933168790@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
By implementing the acquire/release protocol, the SOR reset can be
shared with other drivers that also adhere to this protocol, such as the
PMC driver that uses the same reset as part of the powergate and -ungate
implementation using generic power domains.
Runtime PM makes sure that the operations are executed in the right
order, and the reset core has error handling and WARNs in place to make
sure the acquire/release protocol is followed.
Signed-off-by: Thierry Reding <treding@nvidia.com>
This set of changes starts of with some refactoring of the CEC support
to make it reusable on Tegra210 and later. Following are a couple of
fixes for HDMI audio support (via HDA).
The bulk here is a set of preparatory patches working towards enabling
Tegra186 support for host1x and VIC. Additional patches will be needed
to fully enable this, but they're not quite ready yet.
To round things off, this also adds support for configuring the SOR
crossbar using device tree, and fixes a couple of job-related issues in
the host1x code.
-----BEGIN PGP SIGNATURE-----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=jS/6
-----END PGP SIGNATURE-----
Merge tag 'drm/tegra/for-5.1-rc1' of git://anongit.freedesktop.org/tegra/linux into drm-next
drm/tegra: Changes for v5.1-rc1
This set of changes starts of with some refactoring of the CEC support
to make it reusable on Tegra210 and later. Following are a couple of
fixes for HDMI audio support (via HDA).
The bulk here is a set of preparatory patches working towards enabling
Tegra186 support for host1x and VIC. Additional patches will be needed
to fully enable this, but they're not quite ready yet.
To round things off, this also adds support for configuring the SOR
crossbar using device tree, and fixes a couple of job-related issues in
the host1x code.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Thierry Reding <thierry.reding@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190208144721.25830-1-thierry.reding@gmail.com
The crossbar configuration is usually the same across all designs for a
given SoC generation. But sometimes there are designs that require some
other configuration.
Implement support for parsing the crossbar configuration from a device
tree. If the crossbar configuration is not present in the device tree,
fall back to the default crossbar configuration.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The HDA format data passed to the SOR from the HDA codec contains more
information than just the rate and number of channels. Parse all the
fields and store them in an internal structure for subsequent use.
While at it, also fix an off-by-one error in the number of channels.
Signed-off-by: Thierry Reding <treding@nvidia.com>
drm-next has been forwarded to 5.0-rc1, and we need it to apply the damage
helper for dirtyfb series from Noralf Trønnes.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Make life easier for drivers by simply passing the connector
to drm_hdmi_avi_infoframe_from_display_mode() and
drm_hdmi_avi_infoframe_quant_range(). That way drivers don't
need to worry about is_hdmi2_sink mess.
v2: Make is_hdmi2_sink() return true for sil-sii8620
Adapt to omap/vc4 changes
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: "David (ChunMing) Zhou" <David1.Zhou@amd.com>
Cc: Archit Taneja <architt@codeaurora.org>
Cc: Andrzej Hajda <a.hajda@samsung.com>
Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com>
Cc: Inki Dae <inki.dae@samsung.com>
Cc: Joonyoung Shim <jy0922.shim@samsung.com>
Cc: Seung-Woo Kim <sw0312.kim@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: CK Hu <ck.hu@mediatek.com>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: Rob Clark <robdclark@gmail.com>
Cc: Ben Skeggs <bskeggs@redhat.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Sandy Huang <hjc@rock-chips.com>
Cc: "Heiko Stübner" <heiko@sntech.de>
Cc: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Cc: Vincent Abriou <vincent.abriou@st.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Eric Anholt <eric@anholt.net>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Ilia Mirkin <imirkin@alum.mit.edu>
Cc: amd-gfx@lists.freedesktop.org
Cc: linux-arm-msm@vger.kernel.org
Cc: freedreno@lists.freedesktop.org
Cc: nouveau@lists.freedesktop.org
Cc: linux-tegra@vger.kernel.org
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190108172828.15184-1-ville.syrjala@linux.intel.com
If the SOR is already up and running when the kernel driver is probed,
setting a mode will typically fail. This can be seen for example on
Jetson TX2. Under certain circumstances the generic power domain code
will cause the SOR to be reset. However, if the power domain is never
powered off (this can happen if the HDA controller is enabled, which
is part of the same power domain as the SOR), then the SOR will end up
not getting reset and fail to properly set a mode.
To work around this, try to get the reset control and assert/deassert
it, irrespective of whether or not a generic power domain is attached
to the SOR. On platforms where the kernel implements generic power
domains (up to Tegra210) this will fail, because the power domain will
already have acquired an exclusive reference to the reset control. But
on recent platforms there the BPMP provides an ABI to control power
domains, it's possible to acquire the reset control from SOR and use
it to put the SOR into a known good state at probe time.
The proper solution for this is to make the SOR driver capable of
dealing with hardware that's already up and running (by first grace-
fully shutting it down, or perhaps by seamlessly transitioning to the
kernel driver and taking over the running display configuration). That
is fairly involved, though, so we'll go with this quickfix for now.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Remove the temporary workaround of storing the Tegra186 HDMI/DP I/O pad
ID in the SOR driver. The definition has long been available in the
soc/tegra/pmc.h header file.
Signed-off-by: Thierry Reding <treding@nvidia.com>
This code is very similar to the audio over HDMI support on older chips.
Interoperation with the audio codec is done via a pair of codec scratch
registers and an interrupt that is raised at the SOR when the codec has
written those registers.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The SOR implemented in Tegra194 is subtly different from its predecessor
found in Tegra186. Most notably some registers have been moved around so
it is no longer compatible.
Signed-off-by: Thierry Reding <treding@nvidia.com>
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJaW+iVAAoJEHm+PkMAQRiGCDsIAJALNpX7odTx/8y+yCSWbpBH
E57iwr4rmnI6tXJY6gqBUWTYnjAcf4b8IsHGCO6q3WIE3l/kt+m3eA21a32mF2Db
/bfPGTOWu5LoOnFqzgH2kiFuC3Y474toxpld2YtkQWYxi5W7SUtIHi/jGgkUprth
g15yPfwYgotJd/gpmPfBDMPlYDYvLlnPYbTG6ZWdMbg39m2RF2m0BdQ6aBFLHvbJ
IN0tjCM6hrLFBP0+6Zn60pevUW9/AFYotZn2ankNTk5QVCQm14rgQIP+Pfoa5WpE
I25r0DbkG2jKJCq+tlgIJjxHKD37GEDMc4T8/5Y8CNNeT9Q8si9EWvznjaAPazw=
=o5gx
-----END PGP SIGNATURE-----
BackMerge tag 'v4.15-rc8' into drm-next
Linux 4.15-rc8
Daniel requested this for so the intel CI won't fall over on drm-next
so often.
The SOR0 found on Tegra124 and Tegra210 only supports eDP and LVDS and
therefore has a slightly different clock tree than the SOR1 which does
not support eDP, but HDMI and DP instead.
Commit e1335e2f0c ("drm/tegra: sor: Reimplement pad clock") breaks
setups with eDP because the sor->clk_out clock is uninitialized and
therefore setting the parent clock (either the safe clock or either of
the display PLLs) fails, which can cause hangs later on since there is
no clock driving the module.
Fix this by falling back to the module clock for sor->clk_out on those
setups. This guarantees that the module will always be clocked by an
enabled clock and hence prevents those hangs.
Fixes: e1335e2f0c ("drm/tegra: sor: Reimplement pad clock")
Reported-by: Guillaume Tucker <guillaume.tucker@collabora.com>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Traditionally, windows were accessed indirectly, through a register
selection window that required a global register to be programmed with
the index of the window to access. Since the global register could be
written from modesetting functions as well as the interrupt handler
concurrently, accesses had to be serialized using a lock. Using direct
accesses to the window registers the lock can be avoided.
Signed-off-by: Thierry Reding <treding@nvidia.com>
In addition to using the SCDC helpers to enable support for scrambling
for HDMI 2.0 modes, take into account the high pixel clocks when
programming some of the registers.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The SOR found on Tegra186 is very similar to the one found on Tegra210
and earlier. However, due to some changes in the display architecture,
some programming sequences have changed and some register have moved
around.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Future Tegra generations have an increased number of display controllers
that can drive individual SORs. In order to support that, the offset and
layout of some registers has changed in backwards-incompatible ways. Use
parameterized register offsets to support this.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The ->late_register() and ->early_unregister() callbacks are called at
the right time to make sure userspace only accesses interfaces when it
should. Move debugfs registration and unregistration to these callback
functions to avoid potential races with userspace.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Rather create new files within the top-level DRM device's debugfs node,
add the SOR specific files to the connector's debugfs node. This avoids
the need to come up with subdirectory names and is also more intuitive.
Signed-off-by: Thierry Reding <treding@nvidia.com>
After commit 932f652913 ("drm/tegra: sor: Trace register accesses"),
the debugfs register dump implementation causes excessive stack usage
and can result in build warnings. To fix this, move the register
definitions into a table and iterate over the table while dumping the
registers to debugfs.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The current implementation of the pad clock isn't quite correct. This
has the side-effect of being incompatible with the implementation for
Tegra186 (provided by the BPMP) and therefore would require a massive
change to the driver to cope with the differences. Instead, simply do
what Tegra186 does and add some code to fallback to the old behaviour
for existing device trees.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Avoid some boilerplate by calling of_device_get_match_data() instead of
open-coding the equivalent in the driver.
Signed-off-by: Thierry Reding <treding@nvidia.com>
This contains a couple of fixes and improvements for host1x, with some
preparatory work for Tegra186 support.
The remainder is cleanup and minor bugfixes for Tegra DRM along with
enhancements to debuggability.
There have also been some enhancements to the kernel interfaces for
host1x job submissions and support for mmap'ing PRIME buffers directly,
all of which get the interfaces very close to ready for serious work.
-----BEGIN PGP SIGNATURE-----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=ZaxL
-----END PGP SIGNATURE-----
Merge tag 'drm/tegra/for-4.14-rc1' of git://anongit.freedesktop.org/tegra/linux into drm-next
drm/tegra: Changes for v4.14-rc1
This contains a couple of fixes and improvements for host1x, with some
preparatory work for Tegra186 support.
The remainder is cleanup and minor bugfixes for Tegra DRM along with
enhancements to debuggability.
There have also been some enhancements to the kernel interfaces for
host1x job submissions and support for mmap'ing PRIME buffers directly,
all of which get the interfaces very close to ready for serious work.
* tag 'drm/tegra/for-4.14-rc1' of git://anongit.freedesktop.org/tegra/linux: (21 commits)
drm/tegra: Prevent BOs from being freed during job submission
drm/tegra: gem: Implement mmap() for PRIME buffers
drm/tegra: Support render node
drm/tegra: sor: Trace register accesses
drm/tegra: dpaux: Trace register accesses
drm/tegra: dsi: Trace register accesses
drm/tegra: hdmi: Trace register accesses
drm/tegra: dc: Trace register accesses
drm/tegra: sor: Use unsigned int for register offsets
drm/tegra: hdmi: Use unsigned int for register offsets
drm/tegra: dsi: Use unsigned int for register offsets
drm/tegra: dpaux: Use unsigned int for register offsets
drm/tegra: dc: Use unsigned int for register offsets
drm/tegra: Fix NULL deref in debugfs/iova
drm/tegra: switch to drm_*_get(), drm_*_put() helpers
drm/tegra: Set MODULE_FIRMWARE for the VIC
drm/tegra: Add CONFIG_OF dependency
gpu: host1x: Support sub-devices recursively
gpu: host1x: fix error return code in host1x_probe()
gpu: host1x: Fix bitshift/mask multipliers
...
