Add cciss_allow_hpsa module parameter. This parameter causes
the cciss driver to ignore any Smart Array devices known to be
supported by the hpsa driver.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Fix multiple calls to pci_release_regions. If cciss_pci_init
fails, it already does any necessary call to pci_release_regions,
so this does not need to be done again in cciss_init_one in that
case.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
* 'for-linus' of git://git.kernel.dk/linux-2.6-block: (41 commits)
Revert "Seperate read and write statistics of in_flight requests"
cfq-iosched: don't delay async queue if it hasn't dispatched at all
block: Topology ioctls
cfq-iosched: use assigned slice sync value, not default
cfq-iosched: rename 'desktop' sysfs entry to 'low_latency'
cfq-iosched: implement slower async initiate and queue ramp up
cfq-iosched: delay async IO dispatch, if sync IO was just done
cfq-iosched: add a knob for desktop interactiveness
Add a tracepoint for block request remapping
block: allow large discard requests
block: use normal I/O path for discard requests
swapfile: avoid NULL pointer dereference in swapon when s_bdev is NULL
fs/bio.c: move EXPORT* macros to line after function
Add missing blk_trace_remove_sysfs to be in pair with blk_trace_init_sysfs
cciss: fix build when !PROC_FS
block: Do not clamp max_hw_sectors for stacking devices
block: Set max_sectors correctly for stacking devices
cciss: cciss_host_attr_groups should be const
cciss: Dynamically allocate the drive_info_struct for each logical drive.
cciss: Add usage_count attribute to each logical drive in /sys
...
Fix these build errors when CONFIG_PROC_FS is not set:
drivers/block/cciss.c: In function 'cciss_show_raid_level':
drivers/block/cciss.c:623: error: 'RAID_UNKNOWN' undeclared (first use in this function)
drivers/block/cciss.c:626: error: 'raid_label' undeclared (first use in this function)
drivers/block/cciss.c: In function 'cciss_geometry_inquiry':
drivers/block/cciss.c:2696: error: 'RAID_UNKNOWN' undeclared (first use in this function)
Signed-off-by: Alexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
cciss: Dynamically allocate the drive_info_struct for each logical drive.
This reduces the size of the per-hba ctlr_info structure from 106936
bytes to 8132 bytes. That's on 32-bit systems. On 64-bit systems, the
improvement is even bigger. Without this, the ctlr_info struct is so big
that the driver won't even load on a 64 bit system if CISS_MAX_LUN was
at it's current setting of 1024 logical drives.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Add usage_count attribute to each logical drive at
/sys/devices/<dev>/ccissX/cXdY/usage_count for controller X,
logical drive Y. The usage count is the number of times
the device has currently been opened.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
and change get rid of some magic numbers in raid lavel decoding.
Add raid_level attribute to each logical drive at
/sys/devices/<dev>/ccissX/cXdY/raid_level for controller X,
logical drive Y
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
cciss: fix some magic numbers in the raid-level decoding
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Add lunid attribute to each logical drive at
/sys/devices/<dev>/ccissX/cXdY/lunid for controller X,
logical drive Y
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Don't check h->busy_initializing in cciss_open(). Open won't be
called before things are ready, but h->busy_initializing won't be
unset until after the initial rebuild_lun_table is finished. But,
to read the partitions, cciss_open will be called for each logical
drive during rebuild_lun_table. If cciss_open checks h->busy_initializing,
then the reading of the partition information during the initial
rebuild_lun_table will fail, which is especially bad news if it
happens to be your boot device.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Preserve all 8 bytes of the LunID field returned
by CCISS_REPORT_LOGICAL instead of only saving 4 bytes.
This fixes a bug with logical volume addressing encountered on
an MSA2012.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Fix bug that free_hba was calling put_disk for all gendisk[]
pointers -- all 1024 of them -- regardless of whether the were
used or not (NULL). This bug could cause rmmod to oops if logical
drives had been deleted during the driver's lifetime.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
When rebuild_lun_table is reached via sysfs, the usage count that
is checked prior to messing with c0d0 has different constraints
(must be zero) than if rebuild_lun_table is reached via ioctl
(must be one.) Fix rebuild_lun_table to take that into account.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
When removing a logical drive, clear all the information that is
now exposed by sysfs (e.g. vendor, model, serial number.)
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
For c0dx where x is not 0, we handle deletion and addition simply,
but for c0d0, there is the special case that even when there's no
disk, the device node exists so that the controller may be accessed.
So, for c0d0, we only create the sysfs entries once, when a controller
is added, and only remove them once, when a controller is being
taken down.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Handle cases when cciss_add_disk fails.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Handle failure of blk_init_queue gracefully in cciss_add_disk.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Rearrange logical drive sysfs code to make the "changing a disk" path work.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Dynamically allocate struct device for each logical drive as needed
instead of allocating the maximum we would ever need at driver init time.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Remove some unused code in rebuild_lun_table()
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Added /sys/bus/pci/devices/<dev>/ccissX/rescan sysfs entry used
to kick off a rescan that discovers logical drive topology changes.
Signed-off-by: Andrew Patterson <andrew.patterson@hp.com>
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Acked-by: Mike Miller <mike.miller@hp.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Replace the use of one scan kthread per controller with one per driver.
Use a queue to hold a list of controllers that need to be rescanned with
routines to add and remove controllers from the queue.
Fix locking and completion handling to prevent a hang during rmmod.
Signed-off-by: Andrew Patterson <andrew.patterson@hp.com>
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Acked-by: Mike Miller <mike.miller@hp.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Sysfs entries for logical drives need to be removed when a drive is
deleted during driver cleanup.
Signed-off-by: Andrew Patterson <andrew.patterson@hp.com>
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Acked-by: Mike Miller <mike.miller@hp.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Change schedule_timeout() parameter to not be specific to HZ=1000.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: Mike Miller <mike.miller@hp.com>
Cc: Marcin Slusarz <marcin.slusarz@gmail.com>
Cc: "Cameron, Steve" <Steve.Cameron@hp.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Make all seq_operations structs const, to help mitigate against
revectoring user-triggerable function pointers.
This is derived from the grsecurity patch, although generated from scratch
because it's simpler than extracting the changes from there.
Signed-off-by: James Morris <jmorris@namei.org>
Acked-by: Serge Hallyn <serue@us.ibm.com>
Acked-by: Casey Schaufler <casey@schaufler-ca.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Let attribute group vectors be declared "const". We'd
like to let most attribute metadata live in read-only
sections... this is a start.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 22bece00dc
(cciss: fix regression firmware not displayed in procfs)
added a small memory leak in cciss_init_one()
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
* Remove smp_lock.h from files which don't need it (including some headers!)
* Add smp_lock.h to files which do need it
* Make smp_lock.h include conditional in hardirq.h
It's needed only for one kernel_locked() usage which is under CONFIG_PREEMPT
This will make hardirq.h inclusion cheaper for every PREEMPT=n config
(which includes allmodconfig/allyesconfig, BTW)
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When doing an unexpected shutdown like kexec the cciss
firmware might still have some commands in flight, which
it is trying to complete.
The driver is doing it's best on resetting the HBA,
but sadly there's a firmware issue causing the firmware
_not_ to abort or drop old commands.
So the firmware will send us commands which we haven't
accounted for, causing the driver to panic.
With this patch we're just ignoring these commands as
there is nothing we could be doing with them anyway.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Acked-by: Mike Miller <mike.miller@hp.com>
Signed-off-by: Jens Axboe <axboe@carl.(none)>
When porting blktrace to tracepoints, we changed to trace/block.h
for trace prober declarations.
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Now that the cciss SCSI error handling routines operate with interrupts
enabled, we no longer need to maintain the list of command completions that
sendcmd() might inadvertantly scoop up, since now it only runs at driver init
time, and there won't be any other commands for it to scoop up. So we
can remove that list and the code that adds to it and processes it.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cca.cpqcorp.net>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Change cciss scsi error handling routines to work with interrupts enabled.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cca.cpqcorp.net>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Separate the error processing from sendcmd_withirq_core from the code
which retries commands. The rationale for this is that the SCSI error
handling code can then be made to use sendcmd_withirq_core, but avoid
retrying commands.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cca.cpqcorp.net>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Factor out code to process target status of completed commands in sendcmd()
and sendcmd_withirq_core(), and fix problem that bad target status was ignored in
sendcmd_withirq_core.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cca.cpqcorp.net>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Simplify interfaces of sendcmd() and sendcmd_withirq() so that they
provide only one way to address commands instead of three ways.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cca.cpqcorp.net>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Factor the core of sendcmd_withirq out to provide a simpler interface
which provides access to full error information.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cca.cpqcorp.net>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Add sysfs entries to the cciss driver needed for the dm/multipath tools.
A file for vendor, model, rev, and unique_id is added for each logical
drive under directory /sys/bus/pci/devices/<dev>/ccissX/cXdY. Where X =
the controller (or host) number and Y is the logical drive number.
A link from /sys/bus/pci/devices/<dev>/ccissX/cXdY/block:cciss!cXdY to
/sys/block/cciss!cXdY/device is also created. A bus is created in
/sys/bus/cciss. A link is created from the pci ccissX entry to
/sys/bus/cciss/devices/ccissX. Please consider this for inclusion.
Signed-off-by: Mike Miller <mike.miller@hp.com>
Cc: Stephen M. Cameron <scameron@beardog.cca.cpqcorp.net>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Fix the SCSI reset error handler to send a working, properly addressed
reset message to the target device and add code to wait for the target
device to become ready by polling it with Test Unit Ready.
The existing reset code was broken in that it didn't bother to set the
8-byte LUN address to anything besides zero, so the command was addressed
to the controller, which pretended to the driver that the command
succeeded, while doing nothing. Ages ago I tested this code, but
unbeknownst to me, my test was flawed, and what I thought was a tape drive
getting reset was actually nothing of the sort. Unfortunately, there is
still lots of Smartarray firmware that doesn't handle doing target resets
right, and this code won't help in those cases, but it also shouldn't make
things worse in those cases than they already are.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cca.cpqcorp.net>
Cc: Mike Miller <mikem@beardog.cca.cpqcorp.net>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Factor out the core of sendcmd() to provide a simpler interface which
exposes all the error information to the caller and make the original
sendcmd use this new function. Rationale: The SCSI error handling
routines need to send commands with interrupts turned off, but they also
need access to the full error information.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cca.cpqcorp.net>
Cc: Mike Miller <mikem@beardog.cca.cpqcorp.net>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Until now we have had a 1:1 mapping between storage device physical
block size and the logical block sized used when addressing the device.
With SATA 4KB drives coming out that will no longer be the case. The
sector size will be 4KB but the logical block size will remain
512-bytes. Hence we need to distinguish between the physical block size
and the logical ditto.
This patch renames hardsect_size to logical_block_size.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Till now block layer allowed two separate modes of request execution.
A request is always acquired from the request queue via
elv_next_request(). After that, drivers are free to either dequeue it
or process it without dequeueing. Dequeue allows elv_next_request()
to return the next request so that multiple requests can be in flight.
Executing requests without dequeueing has its merits mostly in
allowing drivers for simpler devices which can't do sg to deal with
segments only without considering request boundary. However, the
benefit this brings is dubious and declining while the cost of the API
ambiguity is increasing. Segment based drivers are usually for very
old or limited devices and as converting to dequeueing model isn't
difficult, it doesn't justify the API overhead it puts on block layer
and its more modern users.
Previous patches converted all block low level drivers to dequeueing
model. This patch completes the API transition by...
* renaming elv_next_request() to blk_peek_request()
* renaming blkdev_dequeue_request() to blk_start_request()
* adding blk_fetch_request() which is combination of peek and start
* disallowing completion of queued (not started) requests
* applying new API to all LLDs
Renamings are for consistency and to break out of tree code so that
it's apparent that out of tree drivers need updating.
[ Impact: block request issue API cleanup, no functional change ]
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Mike Miller <mike.miller@hp.com>
Cc: unsik Kim <donari75@gmail.com>
Cc: Paul Clements <paul.clements@steeleye.com>
Cc: Tim Waugh <tim@cyberelk.net>
Cc: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Laurent Vivier <Laurent@lvivier.info>
Cc: Jeff Garzik <jgarzik@pobox.com>
Cc: Jeremy Fitzhardinge <jeremy@xensource.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Adrian McMenamin <adrian@mcmen.demon.co.uk>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Cc: Borislav Petkov <petkovbb@googlemail.com>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Alex Dubov <oakad@yahoo.com>
Cc: Pierre Ossman <drzeus@drzeus.cx>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Markus Lidel <Markus.Lidel@shadowconnect.com>
Cc: Stefan Weinhuber <wein@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Pete Zaitcev <zaitcev@redhat.com>
Cc: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
With recent cleanups, there is no place where low level driver
directly manipulates request fields. This means that the 'hard'
request fields always equal the !hard fields. Convert all
rq->sectors, nr_sectors and current_nr_sectors references to
accessors.
While at it, drop superflous blk_rq_pos() < 0 test in swim.c.
[ Impact: use pos and nr_sectors accessors ]
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Tested-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Tested-by: Adrian McMenamin <adrian@mcmen.demon.co.uk>
Acked-by: Adrian McMenamin <adrian@mcmen.demon.co.uk>
Acked-by: Mike Miller <mike.miller@hp.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Cc: Borislav Petkov <petkovbb@googlemail.com>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Eric Moore <Eric.Moore@lsi.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Pete Zaitcev <zaitcev@redhat.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Paul Clements <paul.clements@steeleye.com>
Cc: Tim Waugh <tim@cyberelk.net>
Cc: Jeff Garzik <jgarzik@pobox.com>
Cc: Jeremy Fitzhardinge <jeremy@xensource.com>
Cc: Alex Dubov <oakad@yahoo.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Dario Ballabio <ballabio_dario@emc.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: unsik Kim <donari75@gmail.com>
Cc: Laurent Vivier <Laurent@lvivier.info>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
rq->data_len served two purposes - the length of data buffer on issue
and the residual count on completion. This duality creates some
headaches.
First of all, block layer and low level drivers can't really determine
what rq->data_len contains while a request is executing. It could be
the total request length or it coulde be anything else one of the
lower layers is using to keep track of residual count. This
complicates things because blk_rq_bytes() and thus
[__]blk_end_request_all() relies on rq->data_len for PC commands.
Drivers which want to report residual count should first cache the
total request length, update rq->data_len and then complete the
request with the cached data length.
Secondly, it makes requests default to reporting full residual count,
ie. reporting that no data transfer occurred. The residual count is
an exception not the norm; however, the driver should clear
rq->data_len to zero to signify the normal cases while leaving it
alone means no data transfer occurred at all. This reverse default
behavior complicates code unnecessarily and renders block PC on some
drivers (ide-tape/floppy) unuseable.
This patch adds rq->resid_len which is used only for residual count.
While at it, remove now unnecessasry blk_rq_bytes() caching in
ide_pc_intr() as rq->data_len is not changed anymore.
Boaz : spotted missing conversion in osd
Sergei : spotted too early conversion to blk_rq_bytes() in ide-tape
[ Impact: cleanup residual count handling, report 0 resid by default ]
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Cc: Borislav Petkov <petkovbb@googlemail.com>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Mike Miller <mike.miller@hp.com>
Cc: Eric Moore <Eric.Moore@lsi.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Doug Gilbert <dgilbert@interlog.com>
Cc: Mike Miller <mike.miller@hp.com>
Cc: Eric Moore <Eric.Moore@lsi.com>
Cc: Darrick J. Wong <djwong@us.ibm.com>
Cc: Pete Zaitcev <zaitcev@redhat.com>
Cc: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
This is the second go through of the old DMA_nBIT_MASK macro,and there're not
so many of them left,so I put them into one patch.I hope this is the last round.
After this the definition of the old DMA_nBIT_MASK macro could be removed.
Signed-off-by: Yang Hongyang <yanghy@cn.fujitsu.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Tony Lindgren <tony@atomide.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Greg KH <greg@kroah.com>
Cc: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
loop: mutex already unlocked in loop_clr_fd()
cfq-iosched: don't let idling interfere with plugging
block: remove unused REQ_UNPLUG
cfq-iosched: kill two unused cfqq flags
cfq-iosched: change dispatch logic to deal with single requests at the time
mflash: initial support
cciss: change to discover first memory BAR
cciss: kernel scan thread for MSA2012
cciss: fix residual count for block pc requests
block: fix inconsistency in I/O stat accounting code
block: elevator quiescing helpers
Replace all DMA_32BIT_MASK macro with DMA_BIT_MASK(32)
Signed-off-by: Yang Hongyang<yanghy@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
