Make the chip info structure data optional by providing reasonable
defaults. Improve corresponding documentation, and highlight the drawback
of not providing explicit chipselect control.
DMA can determine appropriate dma_burst_size and thresholds automatically
so use DMA even if dma_burst_size is not specified.
Signed-off-by: Vernon Sauder <VernonInHand@gmail.com>
Reviewed-by: Ned Forrester <nforrester@whoi.edu>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Minor fixes: remove redundant local variable initialization, fix "can not"
to what I _think_ is a preferred spelling, output IRQ number if requesting
it failed.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@pengutronix.de>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add a pin configuration callback for the s3c24xx SPI driver, as there are
several options depending on the channel and the chip in use.
This is needed as the controller may not have been setup by the initial
bootloader and the fact that the SPI controller gets reset over
suspend/resume into slave mode but the GPIO function registers do not.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Modify spi_write_then_read() to use one transfer. This speeds up all
callers, and is a minor code shrink.
Signed-off-by: Vernon Sauder <Vernon.Sauder@gmail.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Now that arch/ppc is gone we don't need CONFIG_PPC_MERGE anymore
remove the dead code associated with !CONFIG_PPC_MERGE.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: David Brownell <david-b@pacbell.net>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The register definitions have been changed for the mpc5200 PSC ports
to cover some of the changes in the mpc5200b. One change is that the
ccr register is now a u32 instead of a u16. However, for the purposes
of this driver we want to continue to use 16 bit access to avoid
changing the existing (working) behaviour.
This patch allows the driver to continue to do 16 bit accesses without
the compiler complaining about it.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Accept zero (the default!) as a per-transfer clock speed override.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch fixes a build error in the pxa2xx-spi driver,
introduced by commit 7e96445533
("pxa2xx_spi: dma bugfixes")
CC drivers/spi/pxa2xx_spi.o
drivers/spi/pxa2xx_spi.c: In function 'map_dma_buffers':
drivers/spi/pxa2xx_spi.c:331: error: invalid operands to binary &
drivers/spi/pxa2xx_spi.c:331: error: invalid operands to binary &
drivers/spi/pxa2xx_spi.c: In function 'pump_transfers':
drivers/spi/pxa2xx_spi.c:897: warning: format '%lu' expects type 'long unsigned int', but argument 4 has type 'unsigned int'
[dbrownell@users.sourceforge.net: fix warning too ]
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Acked-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix the section mismatch warning generated by the incorrect naming of
s3c24xx_spidrv which should be s3c24xx_spi_driver:
WARNING: drivers/spi/spi_s3c24xx.o(.data+0x4):
Section mismatch in reference from the variable s3c24xx_spidrv
to the (unknown reference) .exit.text:(unknown)
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fixes two DMA bugs in the pxa2xx_spi driver. The first bug is in all
versions of this driver; the second was introduced in the 2.6.20 kernel,
and prevents using the driver with chips like m25p16 flash (which can
issue large DMA reads).
1. Zero length transfers are permitted for use to insert timing,
but pxa2xx_spi.c will fail if this is requested in DMA mode.
Fixed by using programmed I/O (PIO) mode for such transfers.
2. Transfers larger than 8191 are not permitted in DMA mode. A
test for length rejects all large transfers regardless of DMA
or PIO mode. Worked around by rejecting only large transfers
with DMA mapped buffers, and forcing all other transfers
larger than 8191 to use PIO mode. A rate limited warning is
issued for DMA transfers forced to PIO mode.
This patch should apply to all kernels back to and including 2.6.20;
it was test patched against 2.6.20. An additional patch would be
required for older kernels, but those versions are very buggy anyway.
Signed-off-by: Ned Forrester <nforrester@whoi.edu>
Cc: Vernon Sauder <vernoninhand@gmail.com>
Cc: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: <stable@kernel.org> [2.6.25.x, 2.6.26.x]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fixes several chipselect bugs in the pxa2xx_spi driver. These bugs are in
all versions of this driver and prevent using it with chips like m25p16
flash.
1. The spi_transfer.cs_change flag is handled too early:
before spi_transfer.delay_usecs applies, thus making the
delay ineffective at holding chip select.
2. spi_transfer.delay_usecs is ignored on the last transfer
of a message (likewise not holding chipselect long enough).
3. If spi_transfer.cs_change is set on the last transfer, the
chip select is always disabled, instead of the intended
meaning: optionally holding chip select enabled for the
next message.
Those first three bugs were fixed with a relocation of delays
and chip select de-assertions.
4. If a message has the cs_change flag set on the last transfer,
and had the chip select stayed enabled as requested (see 3,
above), it would not have been disabled if the next message is
for a different chip. Fixed by dropping chip select regardless
of cs_change at end of a message, if there is no next message
or if the next message is for a different chip.
This patch should apply to all kernels back to and including 2.6.20;
it was test patched against 2.6.20. An additional patch would be
required for older kernels, but those versions are very buggy anyway.
Signed-off-by: Ned Forrester <nforrester@whoi.edu>
Cc: Vernon Sauder <vernoninhand@gmail.com>
Cc: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: <stable@kernel.org> [2.6.25.x, 2.6.26.x]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Error out on transfer length != multiple of bytes per word with -EINVAL.
Fixes a buffer overrun crash if length < bytes per word.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Acked-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit a61f5345 (spi_mpc83xx clockrate fixes) broke clockrate calculation
for low speeds. SPMODE_DIV16 should be set if the divider is higher than
64, not only if the divider gets clipped to 1024.
Furthermore, the clipping check was off by a factor 16 as well.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When reviewing a recent patch I noticed a potential trouble spot in the
registration of new SPI devices. The SPI master driver is told to set
the device up before adding it to the driver model, so that it's always
properly set up when probe() is called. (This is important, because in
the case of inverted chipselects, this device can make the bus misbehave
until it's properly deselected. It's got to be set up even if no driver
binds to the device.)
The trouble spot is that it doesn't first verify that no other device
has been added using that chipselect. If such a device has been added,
its configuration gets trashed. (Fortunately this has not been a common
error!)
The fix here adds an explicit check, and a mutex to protect the relevant
critical region.
[akpm@linux-foundation.org: make the lock local to spi_add_device()]
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove includes of asm/hardware.h in addition to asm/arch/hardware.h.
Then, since asm/hardware.h only exists to include asm/arch/hardware.h,
update everything to directly include asm/arch/hardware.h and remove
asm/hardware.h.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This adds an SPI driver for the SPI controller found in various Marvell
Orion ARM SoCs. It currently supports only one slave, which must use SPI
mode 0.
[dbrownell@users.sourceforge.net: cleanups, meet specs, pass "sparse"]
Signed-off-by: Shadi Ammouri <shadi@marvell.com>
Signed-off-by: Saeed Bishara <saeed@marvell.com>
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
For some time my at91sam9260 board with JFFS2 on serial flash (m25p80)
would hang when accessing the serial flash and SPI bus. Slowing the SPI
clock down to 9 MHz reduced the occurrence of the hang from "always"
during boot to a nuisance level that allowed other SW development to
continue. Finally had to address this issue when an application stresses
the I/O to always cause a hang.
Hang seems to be caused by a missed SPI interrupt, so that the task ends
up waiting forever after calling spi_sync(). The fix has 2 parts. First
is to halt the DMA engine before the "current" PDC registers are loaded.
This ensures that the "next" registers are loaded before the DMA operation
takes off. The second part of the fix is a kludge that adds a
"completion" interrupt in case the ENDRX interrupt for the last segment of
the DMA chaining operation was missed.
The patch allows the SPI clock for the serial flash to be increased from 9
MHz to 15 MHz (or more?). No hangs or SPI overruns were encountered.
Haavard: while this patch does indeed improve things, I still see overruns
and CRC errors on my NGW100 board when running the DataFlash at 10 MHz.
However, I think some improvement is better than nothing, so I'm passing
this on for inclusion in 2.6.27.
Signed-off-by: Gerard Kam <gerardk5@verizon.net>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix a bug in the spi_s3c24xx driver where it does not reset the registers
of the hardware when resuming from suspend (this block has been reset over
suspend).
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The original "Pass the bus number we expect the S3C24XX SPI driver to
attach to via the platform data." [1] patch was mis-sent, and missed two
important parts of the diff, which was to actually set the bus_num field
and add the relevant field to the platform data.
The previous commit 50f426b55d promised to
add a bus_num field, but failed to include the two hunks that added this
field to include/asm-arm/arch-s3c2410/spi.h and then pass it to the spi
core when creating the new master field in drivers/spi/spi_s3c24xx.c.
[1] git commit 50f426b55d
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The block transfer routine in the mpc52xx psc spi driver misinterpret
the datasheet. According to the processor datasheet the chipselect is
held as long as the EOF is not written.
Theoretically blocks of any sizes can be transferred in this way. The
old routine however writes an EOF after every word, which has the size
of size_of_word. This makes the transfer slow.
Also fixed some duplicate code.
Signed-off-by: Luotao Fu <l.fu@pengutronix.de>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: <stable@kernel.org> [2.6.25.x, 2.6.26.x]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add per-device dma_mapping_ops support for CONFIG_X86_64 as POWER
architecture does:
This enables us to cleanly fix the Calgary IOMMU issue that some devices
are not behind the IOMMU (http://lkml.org/lkml/2008/5/8/423).
I think that per-device dma_mapping_ops support would be also helpful for
KVM people to support PCI passthrough but Andi thinks that this makes it
difficult to support the PCI passthrough (see the above thread). So I
CC'ed this to KVM camp. Comments are appreciated.
A pointer to dma_mapping_ops to struct dev_archdata is added. If the
pointer is non NULL, DMA operations in asm/dma-mapping.h use it. If it's
NULL, the system-wide dma_ops pointer is used as before.
If it's useful for KVM people, I plan to implement a mechanism to register
a hook called when a new pci (or dma capable) device is created (it works
with hot plugging). It enables IOMMUs to set up an appropriate
dma_mapping_ops per device.
The major obstacle is that dma_mapping_error doesn't take a pointer to the
device unlike other DMA operations. So x86 can't have dma_mapping_ops per
device. Note all the POWER IOMMUs use the same dma_mapping_error function
so this is not a problem for POWER but x86 IOMMUs use different
dma_mapping_error functions.
The first patch adds the device argument to dma_mapping_error. The patch
is trivial but large since it touches lots of drivers and dma-mapping.h in
all the architecture.
This patch:
dma_mapping_error() doesn't take a pointer to the device unlike other DMA
operations. So we can't have dma_mapping_ops per device.
Note that POWER already has dma_mapping_ops per device but all the POWER
IOMMUs use the same dma_mapping_error function. x86 IOMMUs use device
argument.
[akpm@linux-foundation.org: fix sge]
[akpm@linux-foundation.org: fix svc_rdma]
[akpm@linux-foundation.org: build fix]
[akpm@linux-foundation.org: fix bnx2x]
[akpm@linux-foundation.org: fix s2io]
[akpm@linux-foundation.org: fix pasemi_mac]
[akpm@linux-foundation.org: fix sdhci]
[akpm@linux-foundation.org: build fix]
[akpm@linux-foundation.org: fix sparc]
[akpm@linux-foundation.org: fix ibmvscsi]
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Muli Ben-Yehuda <muli@il.ibm.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Avi Kivity <avi@qumranet.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
spi_new_device() allocates and registers an spi device all in one swoop.
If the driver needs to add extra data to the spi_device before it is
registered, then this causes problems. This is needed for OF device
tree support so that the SPI device tree helper can add a pointer to
the device node after the device is allocated, but before the device
is registered. OF aware SPI devices can then retrieve data out of the
device node to populate a platform data structure.
This patch splits the allocation and registration portions of code out
of spi_new_device() and creates two new functions; spi_alloc_device()
and spi_register_device(). spi_new_device() is modified to use the new
functions for allocation and registration. None of the existing users
of spi_new_device() should be affected by this change.
Drivers using the new API can forego the use of spi_board_info
structure to describe the device layout and populate data into the
spi_device structure directly.
This change is in preparation for adding an OF device tree parser to
generate spi_devices based on data in the device tree.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Improve PIO transfer mode of au1550 spi controller by continuing of spi
transfer, instead of aborting transfer when transmit underflow interrupt
occurrs.
Verified by oscilloscope that the spi clock pauses on trasmit underflow,
so transfer continuation is perfectly valid even though au1550 datasheet
says that on tx underflow zeroes will be transfered.
Also make some error messages more specific.
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Jan Nikitenko <jan.nikitenko@gmail.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove the Au1550 resource table and instead extract MMIO/IRQ/DMA
resources from platform resource information like any well-behaved
platform driver.
Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: Jan Nikitenko <jan.nikitenko@gmail.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Another step to removing ->ioctl and to removing the BKL
[dbrownell@users.sourceforge.net: take final step; BKL not needed]
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently, 'modalias' in the spi_device structure is a 'const char *'.
The spi_new_device() function fills in the modalias value from a passed in
spi_board_info data block. Since it is a pointer copy, the new spi_device
remains dependent on the spi_board_info structure after the new spi_device
is registered (no other fields in spi_device directly depend on the
spi_board_info structure; all of the other data is copied).
This causes a problem when dynamically propulating the list of attached
SPI devices. For example, in arch/powerpc, the list of SPI devices can be
populated from data in the device tree. With the current code, the device
tree adapter must kmalloc() a new spi_board_info structure for each new
SPI device it finds in the device tree, and there is no simple mechanism
in place for keeping track of these allocations.
This patch changes modalias from a 'const char *' to a fixed char array.
By copying the modalias string instead of referencing it, the dependency
on the spi_board_info structure is eliminated and an outside caller does
not need to maintain a separate spi_board_info allocation for each device.
If searched through the code to the best of my ability for any references
to modalias which may be affected by this change and haven't found
anything. It has been tested with the lite5200b platform in arch/powerpc.
[dbrownell@users.sourceforge.net: cope with linux-next changes: KOBJ_NAME_LEN obliterated, etc]
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use "if SPI_MASTER" to remove numerous dependencies.
[dbrownell@users.sourceforge.net: remove a couple now-needless EXPERIMENTAL dependencies too]
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
xilinx_spi->irq is unsigned, so the test fails
Signed-off-by: Roel Kluin <12o3l@tiscali.nl>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Andrei Konovalov <akonovalov@ru.mvista.com>
Cc: Yuri Frolov <yfrolov@ru.mvista.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This updates the SPI clock rate calculations for the spi_mpc83xx driver.
Some boundary conditions were wrong, and in several cases divide-by-16
wasn't always needed
Signed-off-by: Chen Gong <g.chen@freescale.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This mirrors the functionality that driver_find_device has as well.
We add a start variable, and all callers of the function are fixed up at
the same time.
The block layer will be using this new functionality in a follow-on
patch.
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Switch over to use the shiny new device_create_drvdata() call
instead of the original device_create() calls, so this continues
to work after device_create() is removed.
Note that this driver never had the race which motivated removing
the original call; it locked correctly.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (241 commits)
[ARM] 5171/1: ep93xx: fix compilation of modules using clocks
[ARM] 5133/2: at91sam9g20 defconfig file
[ARM] 5130/4: Support for the at91sam9g20
[ARM] 5160/1: IOP3XX: gpio/gpiolib support
[ARM] at91: Fix NAND FLASH timings for at91sam9x evaluation kits.
[ARM] 5084/1: zylonite: Register AC97 device
[ARM] 5085/2: PXA: Move AC97 over to the new central device declaration model
[ARM] 5120/1: pxa: correct platform driver names for PXA25x and PXA27x UDC drivers
[ARM] 5147/1: pxaficp_ir: drop pxa_gpio_mode calls, as pin setting
[ARM] 5145/1: PXA2xx: provide api to control IrDA pins state
[ARM] 5144/1: pxaficp_ir: cleanup includes
[ARM] pxa: remove pxa_set_cken()
[ARM] pxa: allow clk aliases
[ARM] Feroceon: don't disable BPU on boot
[ARM] Orion: LED support for HP mv2120
[ARM] Orion: add RD88F5181L-FXO support
[ARM] Orion: add RD88F5181L-GE support
[ARM] Orion: add Netgear WNR854T support
[ARM] s3c2410_defconfig: update for current build
[ARM] Acer n30: Minor style and indentation fixes.
...
This got broken by the recent "fix rmmod $spi_driver while spidev-user is
active". I tested the rmmod & write path but didn't check the read path.
I am sorry. The read logic changed and spidev_sync_read() +
spidev_sync_write() do not return zero on success anymore but the number
of bytes that has been transfered over the bus. This patch changes the
logic and copy_to_user() gets called again.
The write path returns the number of bytes which are written to the
underlying device what may be less than the requested size. This patch
makes the same change to the read path or else we request a read of 20
bytes, get 10, don't call copy to user and report to the user that we read
10 bytes.
[akpm@linux-foundation.org: remove test of known-to-be-zero local]
Signed-off-by: Sebastian Siewior <bigeasy@linutronix.de>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
imx_dma_request_by_prio can return channel number by itself.
No need to supply variable address through parameters.
Also converted all drivers using this function.
Signed-off-by: Paulius Zaleckas <paulius.zaleckas@teltonika.lt>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This addresses other oopsing paths in "spidev" by changing how it manages
refcounting. It decouples the lifecycle of the per-device data from the
class device (not just the spi device):
- Use class_{create,destroy} not class_{register,unregister}.
- Use device_{create,destroy} not device_{register,unregister}.
- Free the per-device data only when TWO conditions are true:
* Driver is unbound from underlying SPI device, and
* Device is no longer open (new)
Also, spi_{get,set}_drvdata not dev_{get,set}_drvdata for simpler code.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Sebastian Siewior <bigeasy@tglx.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Somehow the spidev code forgot to include a critical mechanism: when the
underlying device is removed (e.g. spi_master rmmod), open file
descriptors must be prevented from issuing new I/O requests to that
device. On penalty of the oopsing reported by Sebastian Siewior
<bigeasy@tglx.de> ...
This is a partial fix, adding handshaking between the lower level (SPI
messaging) and the file operations using the spi_dev. (It also fixes an
issue where reads and writes didn't return the number of bytes sent or
received.)
There's still a refcounting issue to be addressed (separately).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Reported-by: Sebastian Siewior <bigeasy@tglx.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The current driver may cause glitches on SPI CLK line since one must disable
the SPI controller before changing any HW settings. Fix this by implementing
a local spi_transfer function that won't change speed and/or word size while
CS is active.
While doing that heavy lifting a few other issues were addressed too:
- Make word size 16 and 32 work too.
- Honor bits_per_word and speed_hz in spi transaction.
- Optimize the common path.
This also stops using the "bitbang" framework (except for a few constants).
[Roel Kluin <12o3l@tiscali.nl>: "irq" needs to be signed]
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There is a typo in pxa2xx_spi.c, comment says "Enable the SSP clock", code
says: clk_disable ... so after resume, the SSP is dead.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Ned Forrester <nforrester@whoi.edu>
Cc: Stephen Street <stephen@streetfiresound.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
