Add new attributes to hwmon object for exposing QSFP module temperature
input, fault indication, critical and emergency thresholds. Temperature
input and fault indication are read from Management Temperature Bulk
Register. Temperature thresholds are read from Management Cable Info
Access Register.
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add new fan hwmon attribute for exposing fan faults (fault indication is
read from Fan Out of Range Event Register).
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename cooling device from "Fan" to "mlxsw_fan". Name "Fan" is too
common name, and such name is misleading, while it's interpreted by
user. For example name "Fan" could be used by ACPI.
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace thermal hardcoded temperature trip values with defines.
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Modify thermal zone trip points setting for better alignment with system
thermal requirement.
Add hysteresis thresholds for thermal trips in order to avoid throttling
around thermal trip point. If hysteresis temperature is not considered,
PWM can have side effect of flip up/down on thermal trip point boundary.
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add low frequency bus capability in order to allow core functionality
separation based on bus type. Driver could run over PCIe, which is
considered as high frequency bus or I2C, which is considered as low
frequency bus. In the last case time setting, for example, for thermal
polling interval, should be increased.
Use different thermal monitoring based on bus type. For I2C bus time is
set to 20 seconds, while for PCIe 1 second polling interval is used.
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add new API to read QSFP module's temperature thresholds - warning and
critical.
New internal API reads the temperature thresholds from the modules,
which are equipped with the thermal sensor. These thresholds will be
exposed via hwmon subsystem.
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add FORE (Fan Out of Range Event Register), which is used for fan fault
reading.
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add MTBR (Management Temperature Bulk Register), which is used for port
temperature reading in a bulk mode.
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move QSFP EEPROM definitions to common location from the spectrum driver
in order to make them available for other mlxsw modules. They are common
for all kind of chips and have relation to SFF specifications 8024,
8436, 8472, 8636, rather than to chip type.
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- fix memory leak in in batadv_dat_put_dhcp, by Martin Weinelt
- fix typo, by Sven Eckelmann
- netlink restructuring patch series (part 2), by Sven Eckelmann
(19 patches)
-----BEGIN PGP SIGNATURE-----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=+p14
-----END PGP SIGNATURE-----
Merge tag 'batadv-next-for-davem-20190213' of git://git.open-mesh.org/linux-merge
Simon Wunderlich says:
====================
This feature/cleanup patchset includes the following patches:
- fix memory leak in in batadv_dat_put_dhcp, by Martin Weinelt
- fix typo, by Sven Eckelmann
- netlink restructuring patch series (part 2), by Sven Eckelmann
(19 patches)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to set the error message on this path otherwise some of the
callers, such as test_hints_case(), print from an uninitialized pointer.
We had a similar bug earlier and set "errmsg" to NULL in the caller,
test_delta_action_item(). That code is no longer required so I have
removed it.
Fixes: 9069a3817d ("lib: objagg: implement optimization hints assembly and use hints for object creation")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a typo here. We intended to check "objagg2" but we instead
test "objagg" which is not an error pointer.
Fixes: 9069a3817d ("lib: objagg: implement optimization hints assembly and use hints for object creation")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to set the error code on this path otherwise we return
ERR_PTR(0) which would result in a NULL dereference in the caller.
Fixes: 9069a3817d ("lib: objagg: implement optimization hints assembly and use hints for object creation")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The value of ->num_ports comes from bcm_sf2_sw_probe() and it is less
than or equal to DSA_MAX_PORTS. The ds->ports[] array is used inside
the dsa_is_user_port() and dsa_is_cpu_port() functions. The ds->ports[]
array is allocated in dsa_switch_alloc() and it has ds->num_ports
elements so this leads to a static checker warning about a potential out
of bounds read.
Fixes: 8cfa94984c ("net: dsa: bcm_sf2: add suspend/resume callbacks")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
CR4_QSFP 10G Speed technology should be 10000baseKR_Full
And also report available FEC modes.
Signed-off-by: Vishal Kulkarni <vishal@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jesper Dangaard Brouer says:
====================
Fix page_pool API and dma address storage
As pointed out by David Miller in [1] the current page_pool implementation
stores dma_addr_t in page->private. This won't work on 32-bit platforms with
64-bit DMA addresses since the page->private is an unsigned long and the
dma_addr_t a u64.
Since no driver is yet using the DMA mapping capabilities of the API let's
fix this by storing the information in 'struct page' and use that to store
and retrieve DMA addresses from network drivers.
As long as the addresses returned from dma_map_page() are aligned the first
bit, used by the compound pages code should not be set.
Ilias tested the first two patches on Espressobin driver mvneta, for which
we have patches for using the DMA API of page_pool.
[1]: https://lore.kernel.org/netdev/20181207.230655.1261252486319967024.davem@davemloft.net/
====================
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
As pointed out by Alexander Duyck, the DMA mapping done in page_pool needs
to use the DMA attribute DMA_ATTR_SKIP_CPU_SYNC.
As the principle behind page_pool keeping the pages mapped is that the
driver takes over the DMA-sync steps.
Reported-by: Alexander Duyck <alexander.duyck@gmail.com>
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
As pointed out by David Miller the current page_pool implementation
stores dma_addr_t in page->private.
This won't work on 32-bit platforms with 64-bit DMA addresses since the
page->private is an unsigned long and the dma_addr_t a u64.
A previous patch is adding dma_addr_t on struct page to accommodate this.
This patch adapts the page_pool related functions to use the newly added
struct for storing and retrieving DMA addresses from network drivers.
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The page_pool API is using page->private to store DMA addresses.
As pointed out by David Miller we can't use that on 32-bit architectures
with 64-bit DMA
This patch adds a new dma_addr_t struct to allow storing DMA addresses
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Acked-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the introduction of flow_stats_update(), drivers now update the stats
fields of the passed tc_cls_flower_offload struct, rather than call
tcf_exts_stats_update() directly to update the stats of offloaded TC
flower rules. However, if multiple qdiscs are registered to a TC shared
block and a flower rule is applied, then, when getting stats for the rule,
multiple callbacks may be made.
Take this into consideration by modifying flow_stats_update to gather the
stats from all callbacks. Currently, the values in tc_cls_flower_offload
only account for the last stats callback in the list.
Fixes: 3b1903ef97 ("flow_offload: add statistics retrieval infrastructure and use it")
Signed-off-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Recently introduced tc_setup_flow_action() can fail when parsing tcf_exts
on some unsupported action commands. However, this should not affect the
case when user did not explicitly request hw offload by setting skip_sw
flag. Modify tc_setup_flow_action() callers to only propagate the error if
skip_sw flag is set for filter that is being offloaded, and set extack
error message in that case.
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Fixes: 3a7b68617d ("cls_api: add translator to flow_action representation")
Signed-off-by: David S. Miller <davem@davemloft.net>
With many active TCP sockets, fat TCP sockets could fool
__sk_mem_raise_allocated() thanks to an overflow.
They would increase their share of the memory, instead
of decreasing it.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are some statements that are indented incorrectly. Fix these.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are some statements in an if-block that are not correctly
indented. Fix these.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
dev_consume_skb_irq() should be called in eth_txdone_irq() when skb
xmit done. It makes drop profiles(dropwatch, perf) more friendly.
Signed-off-by: Yang Wei <yang.wei9@zte.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
dev_consume_skb_irq() should be called in at91ether_interrupt() when
skb xmit done. It makes drop profiles(dropwatch, perf) more friendly.
Signed-off-by: Yang Wei <yang.wei9@zte.com.cn>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
dev_consume_skb_irq() should be called when skb xmit done. It makes
drop profiles(dropwatch, perf) more friendly.
Signed-off-by: Yang Wei <yang.wei9@zte.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
dev_consume_skb_irq() should be called in intr_handler() when skb
xmit done. It makes drop profiles(dropwatch, perf) more friendly.
Signed-off-by: Yang Wei <yang.wei9@zte.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
dev_consume_skb_irq() should be called in moxart_tx_finished() when
skb xmit done. It makes drop profiles(dropwatch, perf) more friendly.
Signed-off-by: Yang Wei <yang.wei9@zte.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
dev_consume_skb_irq() should be called in mace_interrupt() when skb
xmit done. It makes drop profiles(dropwatch, perf) more friendly.
Signed-off-by: Yang Wei <yang.wei9@zte.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
dev_consume_skb_irq() should be called when skb xmit done. It makes
drop profiles(dropwatch, perf) more friendly.
Signed-off-by: Yang Wei <yang.wei9@zte.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
dev_consume_skb_irq() should be called in emac_mac_tx_process() when
skb xmit done. It makes drop profiles(dropwatch, perf) more friendly.
Signed-off-by: Yang Wei <yang.wei9@zte.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
dev_consume_skb_irq() should be called when skb xmit done. It makes
drop profiles(dropwatch, perf) more friendly.
Signed-off-by: Yang Wei <yang.wei9@zte.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
The GPIO interrupt controller on the espressobin board only supports edge interrupts.
If one enables the use of hardware interrupts in the device tree for the 88E6341, it is
possible to miss an edge. When this happens, the INTn pin on the Marvell switch is
stuck low and no further interrupts occur.
I found after adding debug statements to mv88e6xxx_g1_irq_thread_work() that there is
a race in handling device interrupts (e.g. PHY link interrupts). Some interrupts are
directly cleared by reading the Global 1 status register. However, the device interrupt
flag, for example, is not cleared until all the unmasked SERDES and PHY ports are serviced.
This is done by reading the relevant SERDES and PHY status register.
The code only services interrupts whose status bit is set at the time of reading its status
register. If an interrupt event occurs after its status is read and before all interrupts
are serviced, then this event will not be serviced and the INTn output pin will remain low.
This is not a problem with polling or level interrupts since the handler will be called
again to process the event. However, it's a big problem when using level interrupts.
The fix presented here is to add a loop around the code servicing switch interrupts. If
any pending interrupts remain after the current set has been handled, we loop and process
the new set. If there are no pending interrupts after servicing, we are sure that INTn has
gone high and we will get an edge when a new event occurs.
Tested on espressobin board.
Fixes: dc30c35be7 ("net: dsa: mv88e6xxx: Implement interrupt support.")
Signed-off-by: John David Anglin <dave.anglin@bell.net>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
phylib enables interrupts before phy_start() has been called, and if
we receive an interrupt in a non-started state, the interrupt handler
returns IRQ_NONE. This causes problems with at least one Marvell chip
as reported by Andrew.
Fix this by handling interrupts the same as in phy_mac_interrupt(),
basically always running the phylib state machine. It knows when it
has to do something and when not.
This change allows to handle interrupts gracefully even if they
occur in a non-started state.
Fixes: 2b3e88ea65 ("net: phy: improve phy state checking")
Reported-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In sctp_stream_init(), after sctp_stream_outq_migrate() freed the
surplus streams' ext, but sctp_stream_alloc_out() returns -ENOMEM,
stream->outcnt will not be set to 'outcnt'.
With the bigger value on stream->outcnt, when closing the assoc and
freeing its streams, the ext of those surplus streams will be freed
again since those stream exts were not set to NULL after freeing in
sctp_stream_outq_migrate(). Then the invalid-free issue reported by
syzbot would be triggered.
We fix it by simply setting them to NULL after freeing.
Fixes: 5bbbbe32a4 ("sctp: introduce stream scheduler foundations")
Reported-by: syzbot+58e480e7b28f2d890bfd@syzkaller.appspotmail.com
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jianlin reported a panic when running sctp gso over gre over vlan device:
[ 84.772930] RIP: 0010:do_csum+0x6d/0x170
[ 84.790605] Call Trace:
[ 84.791054] csum_partial+0xd/0x20
[ 84.791657] gre_gso_segment+0x2c3/0x390
[ 84.792364] inet_gso_segment+0x161/0x3e0
[ 84.793071] skb_mac_gso_segment+0xb8/0x120
[ 84.793846] __skb_gso_segment+0x7e/0x180
[ 84.794581] validate_xmit_skb+0x141/0x2e0
[ 84.795297] __dev_queue_xmit+0x258/0x8f0
[ 84.795949] ? eth_header+0x26/0xc0
[ 84.796581] ip_finish_output2+0x196/0x430
[ 84.797295] ? skb_gso_validate_network_len+0x11/0x80
[ 84.798183] ? ip_finish_output+0x169/0x270
[ 84.798875] ip_output+0x6c/0xe0
[ 84.799413] ? ip_append_data.part.50+0xc0/0xc0
[ 84.800145] iptunnel_xmit+0x144/0x1c0
[ 84.800814] ip_tunnel_xmit+0x62d/0x930 [ip_tunnel]
[ 84.801699] gre_tap_xmit+0xac/0xf0 [ip_gre]
[ 84.802395] dev_hard_start_xmit+0xa5/0x210
[ 84.803086] sch_direct_xmit+0x14f/0x340
[ 84.803733] __dev_queue_xmit+0x799/0x8f0
[ 84.804472] ip_finish_output2+0x2e0/0x430
[ 84.805255] ? skb_gso_validate_network_len+0x11/0x80
[ 84.806154] ip_output+0x6c/0xe0
[ 84.806721] ? ip_append_data.part.50+0xc0/0xc0
[ 84.807516] sctp_packet_transmit+0x716/0xa10 [sctp]
[ 84.808337] sctp_outq_flush+0xd7/0x880 [sctp]
It was caused by SKB_GSO_CB(skb)->csum_start not set in sctp_gso_segment.
sctp_gso_segment() calls skb_segment() with 'feature | NETIF_F_HW_CSUM',
which causes SKB_GSO_CB(skb)->csum_start not to be set in skb_segment().
For TCP/UDP, when feature supports HW_CSUM, CHECKSUM_PARTIAL will be set
and gso_reset_checksum will be called to set SKB_GSO_CB(skb)->csum_start.
So SCTP should do the same as TCP/UDP, to call gso_reset_checksum() when
computing checksum in sctp_gso_segment.
Reported-by: Jianlin Shi <jishi@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Maxime Chevallier says:
====================
net: phy: Add 2.5G/5GBASET PHYs support
The 802.3bz standard defines 2 modes based on the NBASET alliance work
that allow to use 2.5Gbps and 5Gbps speeds on Cat 5e, 6 and 7 cables.
This series adds the necessary infrastructure to handle these modes with
C45 PHYs. This series was originally part of a bigger one, that has
seen 2 iterations [1] [2] that added support for these modes on Marvell
Alaska PHYs.
Following some discussions with Heiner and Andrew [3], we decided to
split-out the generic parts so that we can work together on the
following steps to get these mode fully working with Aquantia and
Marvell PHYS.
The first 3 patches are reworking some of the internal network phy
infrastructure to handle the new modes in a more generic way.
The 4th patch adds all the C45 register definition and accesses that
follows the 802.3bz standard to support 2.5GBASET and 5GBASET.
[1] : https://lore.kernel.org/netdev/20190118152352.26417-1-maxime.chevallier@bootlin.com/
[2] : https://lore.kernel.org/netdev/20190207094939.27369-1-maxime.chevallier@bootlin.com/
[3] : https://lore.kernel.org/netdev/81c340ea-54b0-1abf-94af-b8dc4ee83e3a@gmail.com/
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The 802.3bz specification, based on previous by the NBASET alliance,
defines the 2.5GBaseT and 5GBaseT link modes for ethernet traffic on
cat5e, cat6 and cat7 cables.
These mode integrate with the already defined C45 MDIO PMA/PMD registers
set that added 10G support, by defining some previously reserved bits,
and adding a new register (2.5G/5G Extended abilities).
This commit adds the required definitions in include/uapi/linux/mdio.h
to support these modes, and detect when a link-partner advertises them.
It also adds support for these mode in the generic C45 PHY
infrastructure.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Marvell 10G PHY driver has a generic way of initializing the supported
link modes by reading the PHY's C45 PMA abilities. This can be made
generic, since these registers are part of the 802.3 specifications.
This commit extracts the config_init link_mode initialization code from
marvell10g and uses it to introduce the genphy_c45_pma_read_abilities
function.
Only PMA modes are read, it's still up to the caller to set the Pause
parameters.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since of_set_phy_supported was moved to phy-core.c, we can also move
of_set_phy_eee_broken to the same location, so that we have all OF
functions in the same place.
This patch doesn't intend to introduce any change in behaviour.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
When setting a PHY's max speed using either the max-speed DT property
or ethtool, we should mask-out all non-compatible modes according to the
settings table, instead of just the 10/100BASET modes.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Suggested-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter/IPVS fixes for net
The following patchset contains Netfilter/IPVS fixes for net:
1) Missing structure initialization in ebtables causes splat with
32-bit user level on a 64-bit kernel, from Francesco Ruggeri.
2) Missing dependency on nf_defrag in IPVS IPv6 codebase, from
Andrea Claudi.
3) Fix possible use-after-free from release path of target extensions.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJcZKsDAAoJEEg/ir3gV/o+gewH/3yQYIgVIjibdw1YF5S4vGXV
M0FOsx2OEcaxVjsm+GzWTthARtIO/d5NuYO/j7QsWLopGugTGCSc6SusrVQtH7PY
b5Fz/pR+ElArt0Ovx06A1twdO5gtoT920rP+E+Gvl/ZR78ceknHUGxJBnGEh2p9D
svM3Q4mdmJZ+a3ehMCxMWS2vf7If43fhHXyt9OKEMpbzAJ03MVLVagt3OGUNi6QP
vl4Fuq5OX6zumKLXPpql8kh+Fbu9QHc8vcuwPnG8GmsBetS083HSC6EPRUbo/EPR
3IzuAibltXoYWlvCPpotCjjSuyqvkOdVudD5jyM3gFIS3XuJdnwkn6k5gvPCk6E=
=W+Ws
-----END PGP SIGNATURE-----
Merge tag 'mlx5-fixes-2019-02-13' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
Mellanox, mlx5 fixes 2019-02-13
This series introduces some fixes to mlx5 driver.
For more information please see tag log below.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently mlx5 driver creates xdp redirect hw queues unconditionally on
netdevice open, This is great until someone starts redirecting XDP traffic
via ndo_xdp_xmit on mlx5 device and changes the device configuration at
the same time, this might cause crashes, since the other device's napi
is not aware of the mlx5 state change (resources un-availability).
To fix this we must synchronize with other devices napi's on the system.
Added a new flag under mlx5e_priv to determine XDP TX resources are
available, set/clear it up when necessary and use synchronize_rcu()
when the flag is turned off, so other napi's are in-sync with it, before
we actually cleanup the hw resources.
The flag is tested prior to committing to transmit on mlx5e_xdp_xmit, and
it is sufficient to determine if it safe to transmit or not. The other
two internal flags (MLX5E_STATE_OPENED and MLX5E_SQ_STATE_ENABLED) become
unnecessary. Thus, they are removed from data path.
Fixes: 58b99ee3e3 ("net/mlx5e: Add support for XDP_REDIRECT in device-out side")
Reported-by: Toke Høiland-Jørgensen <toke@redhat.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Eliminate the following compilation warning:
drivers/net/ethernet/mellanox/mlx5/core/events.c: warning: 'error_str'
may be used uninitialized in this function [-Wuninitialized]: => 238:3
Fixes: c2fb3db22d ("net/mlx5: Rework handling of port module events")
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Reviewed-by: Mikhael Goikhman <migo@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
When EEH is injected and PCI bus stalls, mlx5's pci error detect
function is called to deactivate the command interface and tear down
the device. The issue is that there can be a thread that already
passed MLX5_DEVICE_STATE_INTERNAL_ERROR check, it will send the command
and stuck in the wait_func.
Solution:
Add function mlx5_cmd_flush to disable command interface and clear all
the pending commands. When device state is set to
MLX5_DEVICE_STATE_INTERNAL_ERROR, call mlx5_cmd_flush to ensure all
pending threads waiting for firmware commands completion are terminated.
Fixes: c1d4d2e92a ("net/mlx5: Avoid calling sleeping function by the health poll thread")
Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Reviewed-by: Daniel Jurgens <danielj@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
New channels are applied to the priv channels only after they
are successfully opened. Then, the indirection table should be built
according to the new number of channels.
Currently, such build is preformed independently of whether the
channels opening is successful, and is not reverted on failure.
The bug is caused due to removal of rss params from channels struct
and moving it to priv struct. That change cause to independency between
channels and rss params.
This causes a crash on a later point, when accessing rqn of a non
existing channel.
This patch fixes it by moving the indirection table build right before
switching the priv channels to new channels struct, after the new set of
channels was successfully opened.
Fixes: bbeb53b8b2 ("net/mlx5e: Move RSS params to a dedicated struct")
Signed-off-by: Maria Pasechnik <mariap@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
