The SREV register in the WMAC register space does not contain the chip
revision, so it needs to be passed in from the kernel.
With an updated kernel, this fixes tx gain table selection.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Conflicts:
Documentation/devicetree/bindings/net/micrel-ks8851.txt
net/core/netpoll.c
The net/core/netpoll.c conflict is a bug fix in 'net' happening
to code which is completely removed in 'net-next'.
In micrel-ks8851.txt we simply have overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
Along with AR9340 and AR955x, this is also needed for
the QCA953x SoC.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The commit "ath9k: reduce baseband hang detection false positive rate"
added a delay in the loop checking the baseband state, however it was
unreachable due to previous 'continue' statements.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Check if the baseband state remains stable, and add a small delay
between register reads.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There is no benefit in retaining the legacy rate control module
in the driver codebase.
It is known to be buggy and has less than optimal performance
in real-world environments compared with minstrel. The only
reason that it was kept when we made the switch to minstrel
as default was that it showed higher throughput numbers in a
clean/ideal environment.
This is no longer the case and minstrel can push ath9k to
the same throughput levels. In TCP, with 3-stream cards, more than
295 Mbps can be obtained in open air, with 2-stream cards,
210 Mbps is easily reached. To test performance issues,
instead of using a broken rate control module, it is better
to use the fixed-rate interface provided by mac80211 anyway.
The ath9k RC has not received any bug fixes in years and is
just bit-rotting away - this patch removes it.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The threshold values for RX interrupt mitigation
are different for AR9003 and AR9002 families.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fast Channel Change across bands was enabled for
AR9462 recently, but this is causing baseband issues.
Disable it until this feature is tested well. Also,
remove the feature bit for AR9565 since it is
a single-band card and doesn't support this feature.
Cc: stable@vger.kernel.org
Reported-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
AR9100 requires a larger delay after waking up
the RTC.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Move initialization of config variables to
ath9k_hw_init_config().
* Move initialization of defaults to ath9k_hw_init_defaults().
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There is no point in trying to bring up the chip when
the MAC version is not present in the supported list.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The PHY restart workaround that handles baseband hangs
for packets with unsupported rates is required only
for a HW bug in AR9300 v2.2. All the subsequent chips in
the AR9003 family do not require this driver fix since
it has been addressed in the HW.
Since the value of the AR_PHY_RESTART register is written
with the default initvals, make sure that PHY restart is
always disabled once this particular BB hang signaure has
been encountered.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is required for adding separate hang check
routines for AR9002 and AR9003.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
HW hang checks have to be done on a per-chip basis.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since the unit is microseconds and not milliseconds, tv_sec needs to be
multiplied by 1000000, not 1000.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If a gentimer has both the trigger and the overflow bits set, only
mask out the trigger bit if an overflow handler is present.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath9k_hw should not depend on any ath9k data structures like ath_softc
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The delay that is required after issuing a RTC reset
varies for each chip. Handle this properly.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The small delay that is present between a RTC reset/clear
operation is required for the chip to settle and this is
needed for all chips, not just the AR9002 family.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove unused fields, pass timer info in usec instead of TU.
Preparation for fixing nexttbtt calculation
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove ah->config.spurmode and ah->config.spurchans, always use EEPROM
data.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The hardware does not have support for ATIM processing, and the driver
does not set up ah->atim_window anywhere. Additionally, the code can
clobber the timer used by P2P powersave.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
- Use generic bitops instead of custom hackery
- Move interrupt enable/disable logic from ath9k to ath9k_hw
- Decouple ISR call from btcoex
- Make the overflow callback optional (to prevent IRQ storms)
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Move ath9k_hw_set_rfmode() after ath9k_hw_process_ini() in order to avoid
AR_PHY_MODE register is overwritten with default values by
ar9003_hw_process_ini()
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Adjusting the CCA registers for maximum permissible
noise floor in ETSI/Japan domains has to be done for
all AR9003 family chips.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The CHANNEL_HT flag is insignificant for fast channel change conditions,
since it does not affect any important part of the hardware reset /
channel setup.
Scanning usually runs with HT disabled, so this change will slightly
improve scan time on many chipsets.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
A cold reset can be triggered because of DMA stop issues, and this leads
to TSF being cleared on all chipsets. To properly deal with this, always
save the TSF.
Additionally, account for the time it takes to do the actual chip reset,
which can be quite significant. On AR9344 it takes around 4.5 ms.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This HW config option is always set to true and is not needed.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Code in ath9k_hw_set_clockrate function indicates that ah->curchan
(and thus chan local variable) may be NULL. If that is indeed the
case, IS_CHAN_HT40(chan) check has to be performed only in branch
where chan is not NULL. Moving the code under already existing
if condition fixes this issue.
Signed-off-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add nf parameter to ath9k_hw_getchan_noise() in order to compute NF for EXT
chains with the same scale of noise floor calculated on CTL chains.
ath9k_hw_getchan_noise() will be used in ath_process_fft() for spectral scan on
HT40 channels
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Accessing it to get the current operating channel is racy and in the way
of further channel handling related changes
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There was some duplication between channelFlags and chanmode, as well as
a lot of redundant checks based on the combinations of flags.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The hardware is always configured with OFDM support enabled
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Hardware 802.11b-only mode isn't supported by the driver (the device is
configured for 802.11n/g instead). Simplify the code by removing checks
for it.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use wrappers where available. Simplifies code and helps with further
improvements to the channel data structure
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
