Fix sparse warning:
drivers/gpu/drm/bridge/sii902x.c:665:5: warning:
symbol 'sii902x_audio_digital_mute' was not declared. Should it be static?
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190614153623.28708-1-yuehaibing@huawei.com
When using an I2S source using a different clock source (usually the I2S
audio HW uses dedicated PLLs, different from the HDMI PHY PLL), fixed
CTS values will cause some frequent audio drop-out and glitches as
reported on Amlogic, Allwinner and Rockchip SoCs setups.
Setting the CTS in automatic mode will let the HDMI controller generate
automatically the CTS value to match the input audio clock.
The DesignWare DW-HDMI User Guide explains:
For Automatic CTS generation
Write "0" on the bit field "CTS_manual", Register 0x3205: AUD_CTS3
The DesignWare DW-HDMI Databook explains :
If "CTS_manual" bit equals 0b this registers contains "audCTS[19:0]"
generated by the Cycle time counter according to specified timing.
Cc: Jernej Skrabec <jernej.skrabec@siol.net>
Cc: Maxime Ripard <maxime.ripard@bootlin.com>
Cc: Jonas Karlman <jonas@kwiboo.se>
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Jernej Skrabec <jernej.skrabec@siol.net>
Tested-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190612085147.26971-1-narmstrong@baylibre.com
To get the chip into the expected state, even when the hardware reset pin
isn't connected, do a software reset in this case. It isn't as thorough as
the hardware reset, as the I2C communication block can not be reset for
obvious reasons, but it's getting the chip into a defined state.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190627085958.28331-1-l.stach@pengutronix.de
In contrast to all of the DSI panel drivers in drivers/gpu/drm/panel
which attach to the DSI host via mipi_dsi_attach() at probe time, the
ADV7533 bridge device does not. Instead it defers this to the point that
the upstream device connects to its bridge via drm_bridge_attach().
The generic Synopsys MIPI DSI host driver does not register it's own
drm_bridge until the MIPI DSI has attached. But it does not call
drm_bridge_attach() on the downstream device until the upstream device
has attached. This leads to a chicken and the egg failure and the DRM
pipeline does not complete.
Since all other mipi_dsi_device drivers call mipi_dsi_attach() in
probe(), make the adv7533 mipi_dsi_device do the same. This ensures that
the Synopsys MIPI DSI host registers it's bridge such that it is
available for the upstream device to connect to.
Signed-off-by: Matt Redfearn <matt.redfearn@thinci.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190627151740.2277-1-matt.redfearn@thinci.com
Transfer size of zero means a request to do an address-only
transfer. Since the HW support this, we probably shouldn't be just
ignoring such requests. While at it allow DP_AUX_I2C_MOT flag to pass
through, since it is supported by the HW as well.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Andrzej Hajda <a.hajda@samsung.com>
Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Andrey Gusakov <andrey.gusakov@cogentembedded.com>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: Cory Tusar <cory.tusar@zii.aero>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: dri-devel@lists.freedesktop.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190619052716.16831-16-andrew.smirnov@gmail.com
We don't need 8 byte array, DP_LINK_STATUS_SIZE (6) should be
enough. This also gets rid of a magic number as a bonus.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Andrzej Hajda <a.hajda@samsung.com>
Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Andrey Gusakov <andrey.gusakov@cogentembedded.com>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: Cory Tusar <cory.tusar@zii.aero>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: dri-devel@lists.freedesktop.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190619052716.16831-15-andrew.smirnov@gmail.com
tc_get_display_props() never reads more than a byte via AUX, so
there's no need to reserve 8 for that purpose. No function change
intended.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Andrzej Hajda <a.hajda@samsung.com>
Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Andrey Gusakov <andrey.gusakov@cogentembedded.com>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: Cory Tusar <cory.tusar@zii.aero>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: dri-devel@lists.freedesktop.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190619052716.16831-14-andrew.smirnov@gmail.com
We never pass anything but 100 as timeout_ms to tc_aux_wait_busy(), so
we may as well hardcode that value and simplify function's signature.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Andrzej Hajda <a.hajda@samsung.com>
Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Andrey Gusakov <andrey.gusakov@cogentembedded.com>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: Cory Tusar <cory.tusar@zii.aero>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: dri-devel@lists.freedesktop.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190619052716.16831-13-andrew.smirnov@gmail.com
tc_wait_pll_lock() is always called as a follow-up for updating
PLLUPDATE and PLLEN bit of a given PLL control register. To simplify
things, merge the two operation into a single helper function
tc_pllupdate() and convert the rest of the code to use it. No
functional change intended.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Andrzej Hajda <a.hajda@samsung.com>
Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Andrey Gusakov <andrey.gusakov@cogentembedded.com>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: Cory Tusar <cory.tusar@zii.aero>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: dri-devel@lists.freedesktop.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190619052716.16831-12-andrew.smirnov@gmail.com
Move common code converting clock rate to an appropriate constant and
configuring SYS_PLLPARAM register into a separate routine and convert
the rest of the code to use it. No functional change intended.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Andrzej Hajda <a.hajda@samsung.com>
Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Andrey Gusakov <andrey.gusakov@cogentembedded.com>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Cory Tusar <cory.tusar@zii.aero>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: dri-devel@lists.freedesktop.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190619052716.16831-11-andrew.smirnov@gmail.com
Don't assume that requested data transfer size is the same as amount
of data that was transferred. Change the code to get that information
from DP0_AUXSTATUS instead.
Since the check for AUX_BUSY in tc_aux_get_status() is pointless (it
will always called after tc_aux_wait_busy()) and there's only one user
of it, inline its code into tc_aux_transfer() instead of trying to
accommodate the change above.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Andrzej Hajda <a.hajda@samsung.com>
Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Andrey Gusakov <andrey.gusakov@cogentembedded.com>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: Cory Tusar <cory.tusar@zii.aero>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: dri-devel@lists.freedesktop.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190619052716.16831-10-andrew.smirnov@gmail.com
According to the datasheet tc358767 can transfer up to 16 bytes via
its AUX channel, so the artificial limit of 8 appears to be too
low. However only up to 15-bytes seem to be actually supported and
trying to use 16-byte transfers results in transfers failing
sporadically (with bogus status in case of I2C transfers), so limit it
to 15.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Andrzej Hajda <a.hajda@samsung.com>
Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Andrey Gusakov <andrey.gusakov@cogentembedded.com>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: Cory Tusar <cory.tusar@zii.aero>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: dri-devel@lists.freedesktop.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190619052716.16831-9-andrew.smirnov@gmail.com
Simplify AUX data write by dropping index arithmetic and shifting and
replacing it with a call to a helper function that does two things:
1. Copies user-provided data into a write buffer
2. Transfers contents of the write buffer to up to 4 32-bit
registers on the chip
Note that separate data endianness fix:
tmp = (tmp << 8) | buf[i];
that was reserved for DP_AUX_I2C_WRITE looks really strange, since it
will place data differently depending on the passed user-data
size. E.g. for a write of 1 byte, data transferred to the chip would
look like:
[byte0] [dummy1] [dummy2] [dummy3]
whereas for a write of 4 bytes we'd get:
[byte3] [byte2] [byte1] [byte0]
Since there's no indication in the datasheet that I2C write buffer
should be treated differently than AUX write buffer and no comment in
the original code explaining why it was done this way, that special
I2C write buffer transformation was dropped in this patch.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Andrzej Hajda <a.hajda@samsung.com>
Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Andrey Gusakov <andrey.gusakov@cogentembedded.com>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: Cory Tusar <cory.tusar@zii.aero>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: dri-devel@lists.freedesktop.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190619052716.16831-8-andrew.smirnov@gmail.com
Simplify AUX data read by removing index arithmetic and shifting with
a helper function that does two things:
1. Fetch data from up to 4 32-bit registers from the chip
2. Copy read data into user provided array.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Andrzej Hajda <a.hajda@samsung.com>
Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Andrey Gusakov <andrey.gusakov@cogentembedded.com>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: Cory Tusar <cory.tusar@zii.aero>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: dri-devel@lists.freedesktop.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190619052716.16831-7-andrew.smirnov@gmail.com
A very unfortunate aspect of tc_write()/tc_read() macro helpers is
that they capture quite a bit of context around them and thus require
the caller to have magic variables 'ret' and 'tc' as well as label
'err'. That makes a number of code paths rather counter-intuitive and
somewhat clunky, for example tc_stream_clock_calc() ends up being like
this:
int ret;
tc_write(DP0_VIDMNGEN1, 32768);
return 0;
err:
return ret;
which is rather surprising when you read the code for the first
time. Since those helpers arguably aren't really saving that much code
and there's no way of fixing them without making them too verbose to
be worth it change the driver code to not use them at all.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Andrzej Hajda <a.hajda@samsung.com>
Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Andrey Gusakov <andrey.gusakov@cogentembedded.com>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: Cory Tusar <cory.tusar@zii.aero>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: dri-devel@lists.freedesktop.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190619052716.16831-6-andrew.smirnov@gmail.com
Implementation of tc_poll_timeout() is almost a 100% copy-and-paste of
the code for regmap_read_poll_timeout(). Replace copied code with a
call to the original. While at it change tc_poll_timeout to accept
"struct tc_data *" instead of "struct regmap *" for brevity. No
functional change intended.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Andrzej Hajda <a.hajda@samsung.com>
Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Andrey Gusakov <andrey.gusakov@cogentembedded.com>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: Cory Tusar <cory.tusar@zii.aero>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: dri-devel@lists.freedesktop.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190619052716.16831-2-andrew.smirnov@gmail.com
The Synopsys MIPI DSI IP contains a video test pattern generator which
is helpful in debugging video timing with connected displays.
Add a debugfs directory containing files which allow the VPG to be
enabled and disabled, and its orientation to be changed.
Signed-off-by: Matt Redfearn <matt.redfearn@thinci.com>
Tested-by: Yannick Fertré <yannick.fertre@st.com>
Reviewed-by: Philippe Cornu <philippe.cornu@st.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190430081646.23845-1-matt.redfearn@thinci.com
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAl0Gj1MeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGctkH/0At3+SQPY2JJSy8
i6+TDeytFx9OggeGLPHChRfehkAlvMb/kd34QHnuEvDqUuCAMU6HZQJFKoK9mvFI
sDJVayPGDSqpm+iv8qLpMBPShiCXYVnGZeVfOdv36jUswL0k6wHV1pz4avFkDeZa
1F4pmI6O2XRkNTYQawbUaFkAngWUCBG9ECLnHJnuIY6ohShBvjI4+E2JUaht+8gO
M2h2b9ieddWmjxV3LTKgsK1v+347RljxdZTWnJ62SCDSEVZvsgSA9W2wnebVhBkJ
drSmrFLxNiM+W45mkbUFmQixRSmjv++oRR096fxAnodBxMw0TDxE1RiMQWE6rVvG
N6MC6xA=
=+B0P
-----END PGP SIGNATURE-----
Merge v5.2-rc5 into drm-next
Maarten needs -rc4 backmerged so he can pull in the fbcon notifier
removal topic branch into drm-misc-next.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
UAPI Changes:
Cross-subsystem Changes:
- Add code to signal all dma-fences when freed with pending signals.
- Annotate reservation object access in CONFIG_DEBUG_MUTEXES
Core Changes:
- Assorted documentation fixes.
- Use irqsave/restore spinlock to add crc entry.
- Move code around to drm_client, for internal modeset clients.
- Make drm_crtc.h and drm_debugfs.h self-contained.
- Remove drm_fb_helper_connector.
- Add bootsplash to todo.
- Fix lock ordering in pan_display_legacy.
- Support pinning buffers to current location in gem-vram.
- Remove the now unused locking functions from gem-vram.
- Remove the now unused kmap-object argument from vram helpers.
- Stop checking return value of debugfs_create.
- Add atomic encoder enable/disable helpers.
- pass drm_atomic_state to atomic connector check.
- Add atomic support for bridge enable/disable.
- Add self refresh helpers to core.
Driver Changes:
- Add extra delay to make MTP SDM845 work.
- Small fixes to virtio, vkms, sii902x, sii9234, ast, mcde, analogix, rockchip.
- Add zpos and ?BGR8888 support to meson.
- More removals of drm_os_linux and drmP headers for amd, radeon, sti, r128, r128, savage, sis.
- Allow synopsis to unwedge the i2c hdmi bus.
- Add orientation quirks for GPD panels.
- Edid cleanups and fixing handling for edid < 1.2.
- Add runtime pm to stm.
- Handle s/r in dw-hdmi.
- Add hooks for power on/off to dsi for stm.
- Remove virtio dirty tracking code, done in drm core.
- Rework BO handling in ast and mgag200.
-----BEGIN PGP SIGNATURE-----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=4uQX
-----END PGP SIGNATURE-----
Merge tag 'drm-misc-next-2019-06-14' of git://anongit.freedesktop.org/drm/drm-misc into drm-next
drm-misc-next for v5.3:
UAPI Changes:
Cross-subsystem Changes:
- Add code to signal all dma-fences when freed with pending signals.
- Annotate reservation object access in CONFIG_DEBUG_MUTEXES
Core Changes:
- Assorted documentation fixes.
- Use irqsave/restore spinlock to add crc entry.
- Move code around to drm_client, for internal modeset clients.
- Make drm_crtc.h and drm_debugfs.h self-contained.
- Remove drm_fb_helper_connector.
- Add bootsplash to todo.
- Fix lock ordering in pan_display_legacy.
- Support pinning buffers to current location in gem-vram.
- Remove the now unused locking functions from gem-vram.
- Remove the now unused kmap-object argument from vram helpers.
- Stop checking return value of debugfs_create.
- Add atomic encoder enable/disable helpers.
- pass drm_atomic_state to atomic connector check.
- Add atomic support for bridge enable/disable.
- Add self refresh helpers to core.
Driver Changes:
- Add extra delay to make MTP SDM845 work.
- Small fixes to virtio, vkms, sii902x, sii9234, ast, mcde, analogix, rockchip.
- Add zpos and ?BGR8888 support to meson.
- More removals of drm_os_linux and drmP headers for amd, radeon, sti, r128, r128, savage, sis.
- Allow synopsis to unwedge the i2c hdmi bus.
- Add orientation quirks for GPD panels.
- Edid cleanups and fixing handling for edid < 1.2.
- Add runtime pm to stm.
- Handle s/r in dw-hdmi.
- Add hooks for power on/off to dsi for stm.
- Remove virtio dirty tracking code, done in drm core.
- Rework BO handling in ast and mgag200.
Tiny conflict in drivers/gpu/drm/amd/display/dc/clk_mgr/clk_mgr.c,
needed #include <linux/slab.h> to make it compile.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
From: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/0e01de30-9797-853c-732f-4a5bd6e61445@linux.intel.com
This converts the Analogix display port to use GPIO descriptors
instead of DT-extracted numbers.
Cc: Douglas Anderson <dianders@chromium.org>
Cc: Sean Paul <seanpaul@chromium.org>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190609231339.22136-1-linus.walleij@linaro.org
This include is only used for some gpio drivers and consumers
that look up GPIO numbers directly from the device tree.
This driver does not use it and only needs <linux/gpio/consumer.h>.
Delete the unused include.
Cc: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Cc: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190609223254.8523-1-linus.walleij@linaro.org
Add power on & off optional physical operation functions, helpful to
program specific registers of the DSI physical part.
Signed-off-by: Yannick Fertré <yannick.fertre@st.com>
Reviewed-by: Philippe Cornu <philippe.cornu@st.com>
Tested-by: Philippe Cornu <philippe.cornu@st.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1558952499-15418-2-git-send-email-yannick.fertre@st.com
On Rockchip rk3288-based Chromebooks when you do a suspend/resume
cycle:
1. You lose the ability to detect an HDMI device being plugged in.
2. If you're using the i2c bus built in to dw_hdmi then it stops
working.
Let's add a hook to the core dw-hdmi driver so that we can call it in
dw_hdmi-rockchip in the next commit.
NOTE: the exact set of steps I've done here in resume come from
looking at the normal dw_hdmi init sequence in upstream Linux plus the
sequence that we did in downstream Chrome OS 3.14. Testing show that
it seems to work, but if an extra step is needed or something here is
not needed we could improve it.
As part of this change we'll refactor the hardware init bits of
dw-hdmi to happen all in one function and all at the same time. Since
we need to init the interrupt mutes before we request the IRQ, this
means moving the hardware init earlier in the function, but there
should be no problems with that. Also as part of this we now
unconditionally init the "i2c" parts of dw-hdmi, but again that ought
to be fine.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20190604204207.168085-1-dianders@chromium.org
In commit 50f9495efe ("drm/bridge/synopsys: dw-hdmi: Add "unwedge"
for ddc bus") I stupidly used IS_ERR() to check for whether we have an
"unwedge" pinctrl state even though on most flows through the driver
the unwedge state will just be NULL.
Fix it so that we consistently use NULL for no unwedge state.
Fixes: 50f9495efe ("drm/bridge/synopsys: dw-hdmi: Add "unwedge" for ddc bus")
Cc: Douglas Anderson <dianders@chromium.org>
Cc: Sean Paul <seanpaul@chromium.org>
Cc: Andrzej Hajda <a.hajda@samsung.com>
Cc: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Jonas Karlman <jonas@kwiboo.se>
Cc: Jernej Skrabec <jernej.skrabec@siol.net>
Cc: Sam Ravnborg <sam@ravnborg.org>
Reported-by: Erico Nunes <nunes.erico@gmail.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20190610175234.196844-1-dianders@chromium.org
Set a drm_bridge_timings in the drm_bridge, and use it to report the
input bus mode (single-link or dual-link). The other fields of the
timings structure are kept to 0 as they do not apply to LVDS buses.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Tested-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
The less than check for the variable num_lanes is always going to be
false because the variable is a u32. Fix this by making num_lanes an
int and also make loop index i an int too.
Addresses-Coverity: ("Unsigned compared against 0")
Fixes: ff5781634c ("drm/bridge: sii902x: Implement HDMI audio support")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Jyri Sarha <jsarha@ti.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190603142102.27191-1-colin.king@canonical.com
This should check that "i" is within bounds before checking reading from
the array.
Fixes: ff5781634c ("drm/bridge: sii902x: Implement HDMI audio support")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190607072704.GA25229@mwanda
See the PhD thesis in the comments in this patch for details, but to
summarize this adds a hacky "unwedge" feature to the dw_hdmi i2c bus to
workaround what appears to be a hardware errata. This relies on a
pinctrl entry to help change around muxing to perform the unwedge.
NOTE that the specific TV this was tested on was the "Samsung
UN40HU6950FXZA" and the specific port was the "STB" port.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20190502225336.206885-2-dianders@chromium.org
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 and
only version 2 as published by the free software foundation this
program is distributed in the hope that it will be useful but
without any warranty without even the implied warranty of
merchantability or fitness for a particular purpose see the gnu
general public license for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 294 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190529141900.825281744@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this software is licensed under the terms of the gnu general public
license version 2 as published by the free software foundation and
may be copied distributed and modified under those terms this
program is distributed in the hope that it will be useful but
without any warranty without even the implied warranty of
merchantability or fitness for a particular purpose see the gnu
general public license for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 285 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190529141900.642774971@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Implement HDMI audio support by using ASoC HDMI codec. The commit
implements the necessary callbacks and configuration for the HDMI
codec and registers a virtual platform device for the codec to attach.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/ef6895d016554b1e0c8b388d4993bcd6a3699341.1558964241.git.jsarha@ti.com
The pixel clock unit in the first two registers (0x00 and 0x01) of
sii9022 is 10kHz, not 1kHz as in struct drm_display_mode. Division by
10 fixes the issue.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1a2a8eae0b9d6333e7a5841026bf7fd65c9ccd09.1558964241.git.jsarha@ti.com
The driver always sets InputBusFmt:EDGE to 0 (falling edge).
Add drm_bridge_timings's input_bus_flags to reflect that the bridge
samples on falling edges.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/deb02a1fd508c514472a4e660092f301e6681361.1558964241.git.jsarha@ti.com
We need to know the link bandwidth to filter out modes we cannot
support, so we need to have read the display props before doing the
filtering.
To ensure we have up to date display props, call tc_get_display_props()
in the beginning of tc_connector_get_modes().
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190528082747.3631-22-tomi.valkeinen@ti.com
In tc_bridge_mode_set callback, we store the pointer to the given
drm_display_mode, and use the mode later. Storing a pointer in such a
way looks very suspicious to me, and I have observed odd issues where
the timings were apparently (at least mostly) zero.
Do a copy of the drm_display_mode instead to ensure we don't refer to
freed/modified data.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190528082747.3631-21-tomi.valkeinen@ti.com
drm_connector_helper_funcs.best_encoder is only needed when the
connector can have more than one encoder, and that is never the case
here.
So remove tc_connector_best_encoder.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190528082747.3631-20-tomi.valkeinen@ti.com
We have tc_connector_mode_valid() to filter out videomdoes that the
tc358767 cannot support. As it is a bridge limitation, change the code
to use drm_bridge_funcs's mode_valid instead.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190528082747.3631-19-tomi.valkeinen@ti.com
tc_main_link_enable() checks if videomode has been set, and fails if
there's no videomode. As tc_main_link_enable() no longer depends on the
videomode, we can drop the check.
Also, while tc_stream_enable() does depend on the videomode, we can
expect that a mode has been set before drm_bridge_funcs.enable is
called, so we don't need the check there either.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190528082747.3631-18-tomi.valkeinen@ti.com
The current link training code does unnecessary retry-loops, and does
extra writes to the registers. It is easier to follow the flow and
ensure it's similar to Toshiba's documentation if we deal with LT inside
tc_main_link_enable() function.
This patch adds tc_wait_link_training() which handles waiting for the LT
phase to finish, and does the necessary LT register setups in
tc_main_link_enable, without extra loops.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190528082747.3631-17-tomi.valkeinen@ti.com
The driver has a loop after ending link training, where it reads the
DPCD link status and prints an error if that status is not ok.
The loop is unnecessary, as far as I can understand from DP specs, so
let's remove it. We can also print the more specific errors to help
debugging.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190528082747.3631-16-tomi.valkeinen@ti.com
At the end of the link training, two steps have to be taken: 1)
tc358767's LT mode is disabled by a write to DP0_SRCCTRL, and 2) Remove
LT flag in DPCD 0x102.
Toshiba's documentation tells to first write the DPCD, then modify
DP0_SRCCTRL. In my testing this often causes issues, and the link
disconnects right after those steps.
If I reverse the steps, it works every time. There's a chance that this
is DP sink specific, though, but as my testing shows this sequence to be
much more reliable, let's change it.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190528082747.3631-15-tomi.valkeinen@ti.com
