Fix a very corner case when the port gets disconnected and the BFA and
FCS layers clean up references to the IT nexus. During this window if a
task management command is issued by the SCSI-ML and ends up referencing
a NULL itnim, it could lead to a crash.
Signed-off-by: Sudarsana Kalluru <sudarsana.kalluru@qlogic.com>
Signed-off-by: Anil Gurumurthy <anil.gurumurthy@qlogic.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Use the common function 'scsi_vpd_tpg_id()' instead of open-coding
it in scsi_dh_alua.
[mkp: Applied by hand]
Signed-off-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Implement scsi_vpd_tpg_id() to extract the target
port group id and the relative port id from
SCSI VPD page 0x83.
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Use scsi_vpd_lun_id() to export the world-wide unique id (wwid) to
sysfs. Note that this is the 'best' wwid according to the rules in
scsi_vpd_lun_id(), not every possible wwid presented by the drive.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add a function scsi_vpd_lun_id() to return a unique device
identifcation based on the designation descriptors of
VPD page 0x83.
As devices might implement several descriptors the order
of preference is:
- NAA IEE Registered Extended
- EUI-64 based 16-byte
- EUI-64 based 12-byte
- NAA IEEE Registered
- NAA IEEE Extended
A SCSI name string descriptor is preferred to all of them
if the identification is longer than 16 bytes.
The returned unique device identification will be formatted
as a SCSI Name string to avoid clashes between different
designator types.
[mkp: Fixed up kernel doc comment from Johannes]
Signed-off-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Ewan Milne <emilne@redhat.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Most sense code is already handled in the generic
code, so we shouldn't be adding special cases here.
However, when doing so we need to check for
unit attention whenever we're sending an internal
command.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Ewan Milne <emilne@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Instead of returning an error code in alua_check_tpgs() we should
rather return the tpgs mode directly and have a cleaner syntax.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Use 'get_unaligned_XX' and 'put_unaligned_XX' instead of
open-coding it.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
We should be using a flag when RTPG extended header is not
supported, that saves us sending RTPG twice for older arrays.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Bart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fixup copy-and-paste error in the description of stpg_endio().
Signed-off-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fixup submit_rtpg() to always return a standard SCSI return code.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Ewan Milne <emilne@redhat.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Use standard logging functions instead of hand-crafted ones.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Ewan Milne <emilne@redhat.com>
Reviewed-by: Bart Van Assche <bvanassche@sandisk.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The only check for a valid sense code is calling scsi_normalize_sense()
and check the return value. So drop the pointless checks and rely on
scsi_normalize_sense() to figure out if the sense code is valid.
With that we can also remove the 'senselen' field.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.com>
Reviewed-by: Bart van Assche <bvanassche@sandisk.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Issue different logging messages if ALUA is not supported
or the TPGS setting is invalid.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The SCSI device now has the VPD page 0x83 information attached,
so there is no need to query it again.
[mkp: Fixed a checkpatch warning]
Signed-off-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Non-disk devices might support ALUA, but the firmware
implementation is untested and frequently broken.
As we're don't actually need it disable ALUA support
for non-disk device for now.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Bart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
device handler initialisation might fail due to a number of
reasons. But as device_handlers are optional this shouldn't
cause us to disable the device entirely.
So just ignore errors from scsi_dh_add_device().
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
As scsi_dh.c is now always compiled in we should be moving
the 'dh_state' attribute to the generic code.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.com>
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The SCSI sd driver probes SCSI devices asynchronously. The sd_remove()
function, called indirectly by device_del(), waits until asynchronous
probing has finished. Since the block layer queue must only be cleaned
up after probing has finished, device_del() has to be called before
blk_cleanup_queue(). Hence revert commit bf2cf3baa2.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Fix a smatch warning:
drivers/scsi/mvsas/mv_sas.c:740 mvs_task_prep() warn: curly braces intended?
The code is correct, the indention is misleading. When the device is not
ready we want to return SAS_PHY_DOWN. But current indentation makes it
look like we only do so in the else branch of if (mvi_dev).
Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Minor issue, fix spelling mistake, Intialization -> Initialization
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The mpt2sas driver was recently folded into mpt3sas to reduce code
duplication.
To avoid problems for people that only have CONFIG_SCSI_MPT2SAS in their
.config we introduce a dummy option that will select MPT3SAS if MPT2SAS
was previously enabled.
This is a temporary measure and we will deprecate this config option in
4.6.
Reported-by: Peter Zijlstra <peterz@infradead.org>
Acked-by: Christoph Hellwig <hch@lst.de>
Acked-by: James Bottomley <James.Bottomley@hansenpartnership.com>
CC: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Change driver version to v1.30.00.22-20151126
Signed-off-by: Ching Huang <ching2048@areca.com.tw>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Split dma resource allocation and io register assignment from get_config
to a new function arcmsr_alloc_io_queue.
Signed-off-by: Ching Huang <ching2048@areca.com.tw>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Ching Huang <ching2048@areca.com.tw>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Changes driver version number.
Signed-off-by: Ching Huang <ching2048@areca.com.tw>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Hannes Reinicke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Support Areca's new PCIe to SATA RAID adapter ARC1203.
Signed-off-by: Ching Huang <ching2048@areca.com.tw>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Hannes Reinicke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Releasing allocated resource if get configuration data failed.
Signed-off-by: Ching Huang <ching2048@areca.com.tw>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Hannes Reinicke <hare@suse.de>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fixed getting wrong configuration data of adapter type B and type D.
Signed-off-by: Ching Huang <ching2048@areca.com.tw>
Reviewed-by: Hannes Reinicke <hare@suse.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Use scsi_host_{get,put}() instead of open-coding these functions.
Compile-tested only.
[mkp: Dropped CC:stable and fixed James Smart's email address]
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: James Smart <james.smart@avagotech.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Even for signed types we have to check for bigger positive value first.
Otherwise it will be never happened.
Signed-off-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Ewan Milne <emilne@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The VPD page information might change, so we need to be able to update
it. This patch implements a VPD page rescan whenever the 'rescan' sysfs
attribute is triggered.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Shane Seymour <shane.seymour@hpe.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
this patch fixes following regression
# targetcli
[Errno 13] Permission denied: '/sys/kernel/config/target/qla2xxx/21:00:00:0e:1e:08:c7:20/tpgt_1/enable'
Fixes: 2eafd72939 ("target: use per-attribute show and store methods")
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
do_div is the wrong way to divide a sector_t, as it is less efficient
when sector_t is 32-bit wide. With the upcoming do_div optimizations,
the kernel starts warning about this:
drivers/scsi/scsi_debug.c: In function 'dif_store':
include/asm-generic/div64.h:207:28: warning: comparison of distinct pointer types lacks a cast
This changes the code to use sector_div instead, which always produces
optimal code.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Hannes Reinicke <hare@suse.de>
Reviewed-by: Sagi Grimberg <sagig@mellanox.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Originally the driver would use of_irq_count to calculate how much
memory is required for storing the interrupt names, since the number of
interrupt sources for the controller is variable. Since of_irq_count
cannot be used by the driver, use fixed names.
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add handlers for fatal interrupts.
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add method for lldd_control_phy. Currently link rate control and spinup
hold is unsupported.
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add function methods for tmf's.
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add functions for scsi host template scan_finished and scan_start
methods.
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add support for smp function, which allows devices attached by expander
to be controlled.
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This is for expander broadcast event.
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add abnormal irq handler. This handler is concerned with phy down event.
Also add port formed and port deformed handlers.
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add functions to deal with lldd_dev_found and lldd_dev_gone.
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add cq interrupt handler and also slot error handler function.
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add path to send ssp command to HW.
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add code to interrupts, so now we can get a phy up interrupt when a disk
is connected.
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add module init code for v1 hw.
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Include initialisation.
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The SAS address for the HBA comes from the device tree.
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Each completion queue has a structure. This is mainly for passing to irq
handler so we know which queue the irq occured on.
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add functionality to init slot indexing.
Slot indexing is for the host to track which slots (or tags) are free
and which are used.
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch also includes relevant memory/pool freeing and sas/scsi host
removal.
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Scan the device tree for all properties. Also do this:
- do ioremap for SAS registers
- allocate memory for interrupt names
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add functionality to register device as a scsi host.
The SAS domain transport ops are empty at this point.
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch adds the initial bare main driver for the HiSilicon SAS
HBA. This only introduces the changes to build and load the main driver
module.
The complete driver consists of the core main module and also a module
platform driver for driving the hw.
The HBA is a platform device.
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The xfer_rdy, command, and task frame's iu structures are not available
in <scsi/sas.h>, but only aic94xx driver folder. Add them to
include/scsi/sas.h
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Move 870-specific init code to a separate function atp870_init()
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Reviewed-by: Hannes Reinicke <hare@suse.de>
Acked-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Move 885-specific init code to a separate function atp885_init()
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Reviewed-by: Hannes Reinicke <hare@suse.de>
Acked-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Move 880-specific init code to a separate function atp880_init()
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Reviewed-by: Hannes Reinicke <hare@suse.de>
Acked-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Call _init_tables before chip-specific initialization. This avoids code
duplication and fixes a bug(?) in 880 init where the values read from flash
into atpdev->sp are then overwritten by calling init_tables.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Reviewed-by: Hannes Reinicke <hare@suse.de>
Acked-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
scam_on is used only during probe, no need to keep it later.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Reviewed-by: Hannes Reinicke <hare@suse.de>
Acked-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Allocate IRQ later during probe to avoid code duplication and also
remove the need for weird locking in _probe.
(It was probably there to prevent race with the IRQ handler?)
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Reviewed-by: Hannes Reinicke <hare@suse.de>
Acked-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Use pci_request_regions and do it before accessing the I/O ports.
Also add missing pci_disable_device() call to atp870u_remove().
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Reviewed-by: Hannes Reinicke <hare@suse.de>
Acked-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Introduce chip type inline functions to simplify code, allowing to delete
dev_id from struct atp_unit.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Reviewed-by: Hannes Reinicke <hare@suse.de>
Acked-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Move shpnt common code to the top, remove base_io, use pci_resource_len.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Reviewed-by: Hannes Reinicke <hare@suse.de>
Acked-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
chip_ver is used for wide chip detection only. Remove it and use a local
variable instead (for 870; 880 and 885 are always wide).
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Reviewed-by: Hannes Reinicke <hare@suse.de>
Acked-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Reviewed-by: Hannes Reinicke <hare@suse.de>
Acked-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Move scsi_host_alloc() to the top of _probe() to remove code duplication,
*p and unneeded atpdev (de)allocation and copying. While at it, fix the
error paths to return real error codes and also add missing
pci_disble_device() call.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Reviewed-by: Hannes Reinicke <hare@suse.de>
Acked-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Reviewed-by: Hannes Reinicke <hare@suse.de>
Acked-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Reviewed-by: Hannes Reinicke <hare@suse.de>
Acked-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Reviewed-by: Hannes Reinicke <hare@suse.de>
Acked-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Reviewed-by: Hannes Reinicke <hare@suse.de>
Acked-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
tscam_885() is empty (except a delay) so remove it.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Reviewed-by: Hannes Reinicke <hare@suse.de>
Acked-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Reviewed-by: Hannes Reinicke <hare@suse.de>
Acked-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The code for setting host adapter ID is the same for all chips.
Move it to a common function.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Reviewed-by: Hannes Reinicke <hare@suse.de>
Acked-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The ioport region is 0x20 bytes long so accessing 0x3a register using
writeb_io is incorrect. Use writeb_base instead.
There's no change in behavior as 870 chips have ioport = baseport.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Reviewed-by: Hannes Reinicke <hare@suse.de>
Acked-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
tscam() is using port 0x80 access for delays but that's x86-only.
Use udelay(2) instead.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Reviewed-by: Hannes Reinicke <hare@suse.de>
Acked-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Reviewed-by: Hannes Reinicke <hare@suse.de>
Acked-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Now that all the is* functions except is885() are gone, rename is885() to
atp_is() to avoid confusion. Don't know what "is" means, though...
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Reviewed-by: Hannes Reinicke <hare@suse.de>
Acked-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Now that is885() supports everything from is870() and the rest of the code
is almost identical, remove is870() and use is885() instead.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Reviewed-by: Hannes Reinicke <hare@suse.de>
Acked-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Move few remaining 870-specific code lines out of is870()
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Reviewed-by: Hannes Reinicke <hare@suse.de>
Acked-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add remaining 870 support to is885():
- different synw, no synuw
- synu[4] = 0x0c
- atp_writeb_io(dev, c, 0x04, 0x00); instead of
atp_writeb_io(dev, c, 0x14, 0x00); (isn't that a bug?)
- atp_writeb_io(dev, c, 0x14, 0xff); instead of
atp_writeb_io(dev, c, 0x14, 0x06);
- different mbuf[3] and mbuf[4] checks
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Reviewed-by: Hannes Reinicke <hare@suse.de>
Acked-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Don't check chip_ver in is870() but add wide_chip parameter for that.
Then add the non-wide support to is885().
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Reviewed-by: Hannes Reinicke <hare@suse.de>
Acked-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Now that is880() and is885() are almost identical (except for some cpu_relax()
calls and debug printks), remove is880() and use is885() instead.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Reviewed-by: Hannes Reinicke <hare@suse.de>
Acked-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Move few chip-specifis lines out of is880() and is885() so they become
almost identical.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Reviewed-by: Hannes Reinicke <hare@suse.de>
Acked-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add channel parameter to is870() and is880() functions to simplify comparing
them with is885().
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Reviewed-by: Hannes Reinicke <hare@suse.de>
Acked-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Unify code formatting in is870(), is880() and is885() functions to simplify
comparing them.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Reviewed-by: Hannes Reinicke <hare@suse.de>
Acked-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Reviewed-by: Hannes Reinicke <hare@suse.de>
Acked-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Subtract 0x40 to use _io access wrappers. Now it's obvious that is870()
and is880() are very similar.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Reviewed-by: Hannes Reinicke <hare@suse.de>
Acked-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Reviewed-by: Hannes Reinicke <hare@suse.de>
Acked-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Introduce *_read? and *_write? wrappers to improve code readability.
Also make sure that baseport is always initialized, not only for ATP880.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Reviewed-by: Hannes Reinicke <hare@suse.de>
Acked-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Reviewed-by: Hannes Reinicke <hare@suse.de>
Acked-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Reviewed-by: Hannes Reinicke <hare@suse.de>
Acked-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Reviewed-by: Hannes Reinicke <hare@suse.de>
Acked-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Reviewed-by: Hannes Reinicke <hare@suse.de>
Acked-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Reviewed-by: Hannes Reinicke <hare@suse.de>
Acked-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Untangle the tmpcip crap so it becomes obvious what ports are accessed.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Reviewed-by: Hannes Reinicke <hare@suse.de>
Acked-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Untangle the tmpcip crap so it becomes obvious what ports are accessed.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Reviewed-by: Hannes Reinicke <hare@suse.de>
Acked-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Untangle the tmport crap so it becomes obvious what ports are accessed.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Reviewed-by: Hannes Reinicke <hare@suse.de>
Acked-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Untangle the tmport crap so it becomes obvious what ports are accessed.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Reviewed-by: Hannes Reinicke <hare@suse.de>
Acked-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Untangle the tmport crap so it becomes obvious what ports are accessed.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Reviewed-by: Hannes Reinicke <hare@suse.de>
Acked-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Untangle the tmport crap so it becomes obvious what ports are accessed.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Reviewed-by: Hannes Reinicke <hare@suse.de>
Acked-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Untangle the tmport crap so it becomes obvious what ports are accessed.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Reviewed-by: Hannes Reinicke <hare@suse.de>
Acked-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Untangle the tmport crap so it becomes obvious what ports are accessed.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Reviewed-by: Hannes Reinicke <hare@suse.de>
Acked-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Untangle the tmport crap so it becomes obvious what ports are accessed.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Reviewed-by: Hannes Reinicke <hare@suse.de>
Acked-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Untangle the tmport crap so it becomes obvious what ports are accessed.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Reviewed-by: Hannes Reinicke <hare@suse.de>
Acked-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Remove tmport1 temporary variable to simplify the code.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Reviewed-by: Hannes Reinicke <hare@suse.de>
Acked-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Remove workport temporary variable to simplify the code.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Reviewed-by: Hannes Reinicke <hare@suse.de>
Acked-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Commit 4f258a4634 ("sd: Fix maximum I/O size for BLOCK_PC requests")
had the unfortunate side-effect of removing an implicit clamp to
BLK_DEF_MAX_SECTORS for REQ_TYPE_FS requests in the block layer
code. This caused problems for some SMR drives.
Debugging this issue revealed a few problems with the existing
infrastructure since the block layer didn't know how to deal with
device-imposed limits, only limits set by the I/O controller.
- Introduce a new queue limit, max_dev_sectors, which is used by the
ULD to signal the maximum sectors for a REQ_TYPE_FS request.
- Ensure that max_dev_sectors is correctly stacked and taken into
account when overriding max_sectors through sysfs.
- Rework sd_read_block_limits() so it saves the max_xfer and opt_xfer
values for later processing.
- In sd_revalidate() set the queue's max_dev_sectors based on the
MAXIMUM TRANSFER LENGTH value in the Block Limits VPD. If this value
is not reported, fall back to a cap based on the CDB TRANSFER LENGTH
field size.
- In sd_revalidate(), use OPTIMAL TRANSFER LENGTH from the Block Limits
VPD--if reported and sane--to signal the preferred device transfer
size for FS requests. Otherwise use BLK_DEF_MAX_SECTORS.
- blk_limits_max_hw_sectors() is no longer used and can be removed.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=93581
Reviewed-by: Christoph Hellwig <hch@lst.de>
Tested-by: sweeneygj@gmx.com
Tested-by: Arzeets <anatol.pomozov@gmail.com>
Tested-by: David Eisner <david.eisner@oriel.oxon.org>
Tested-by: Mario Kicherer <dev@kicherer.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Ruediger Meier observed a regression with the PREVENT ALLOW MEDIUM
REMOVAL command in lk 3.19:
http://www.spinics.net/lists/util-linux-ng/msg11448.html
Inspection indicated the same regression with VERIFY(10).
The patch is against lk 3.19.3 and also works with lk 4.3.0 . With this
patch both commands are accepted and do nothing.
ChangeLog:
- fix the lk 3.19 regression so that the PREVENT ALLOW MEDIUM REMOVAL
command is supported once again
- same fix for VERIFY(10)
Signed-off-by: Douglas Gilbert <dgilbert@interlog.com>
Reviewed-by: Hannes Reinicke <hare@suse.de>
Reviewed-by: Ewan Milne <emilne@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
A device may report an OPTIMAL UNMAP GRANULARITY and UNMAP GRANULARITY
ALIGNMENT in the Block Limits VPD. These parameters describe the
device's internal provisioning allocation units. By default the block
layer will round and align any discard requests based on these limits.
If a device reports LBPRZ=1 to guarantee zeroes after discard, however,
it is imperative that the block layer does not leave out any parts of
the requested block range. Otherwise the device can not do the required
zeroing of any partial allocation units and this can lead to data
corruption.
Since the dm thinp personality relies on the block layer's current
behavior and is unable to deal with partial discard blocks we work
around the problem by setting the granularity to match the logical block
size when LBPRZ is enabled.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The hpsa driver recently started using the sas transport class, but it
does not ensure that the corresponding code is actually built, which
may lead to a link error:
drivers/built-in.o: In function `hpsa_free_sas_phy':
(.text+0x1ce874): undefined reference to `sas_port_delete_phy'
(.text+0x1ce87c): undefined reference to `sas_phy_free'
drivers/built-in.o: In function `hpsa_alloc_sas_port':
(.text+0x1ceb9c): undefined reference to `sas_port_alloc_num'
(.text+0x1ceba8): undefined reference to `sas_port_add'
drivers/built-in.o: In function `hpsa_init':
(.init.text+0x8838): undefined reference to `sas_attach_transport'
(.init.text+0x8868): undefined reference to `sas_release_transport
This adds 'select SCSI_SAS_ATTR' in the Kconfig entry, just like we do
for all other drivers using those functions.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: d04e62b9d6 ("hpsa: add in sas transport class")
Reviewed-by: Christoph Hellwig <hch@lst.de>
Acked-by: Don Brace <don.brace@pmcs.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The initio driver has for many years had two copies of the
same module device table. One of them is also used for registering
the other driver, the other one is entirely useless after the
large scale cleanup that Alan Cox did back in 2007.
The compiler warns about this whenever the driver is built-in:
drivers/scsi/initio.c:131:29: warning: 'i91u_pci_devices' defined but not used [-Wunused-variable]
This removes the extraneous table and the warning.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 72d39fea90 ("[SCSI] initio: Convert into a real Linux driver and update to modern style")
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The advansys drvier uses the request_dma function that is used on ISA
machines for the internal DMA controller, which causes build errors
on platforms that have ISA slots but do not provide the ISA DMA API:
drivers/scsi/advansys.c: In function 'advansys_board_found':
drivers/scsi/advansys.c:11300:10: error: implicit declaration of function 'request_dma' [-Werror=implicit-function-declaration]
The problem now showed up in ARM randconfig builds after commit
6571fb3f8b ("advansys: Update to version 3.5 and remove compilation
warning") made it possible to build on platforms that have neither
VIRT_TO_BUS nor ISA_DMA_API but that do have ISA.
This adds the missing dependency.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
On some host errors storvsc module tries to remove sdev by scheduling a job
which does the following:
sdev = scsi_device_lookup(wrk->host, 0, 0, wrk->lun);
if (sdev) {
scsi_remove_device(sdev);
scsi_device_put(sdev);
}
While this code seems correct the following crash is observed:
general protection fault: 0000 [#1] SMP DEBUG_PAGEALLOC
RIP: 0010:[<ffffffff81169979>] [<ffffffff81169979>] bdi_destroy+0x39/0x220
...
[<ffffffff814aecdc>] ? _raw_spin_unlock_irq+0x2c/0x40
[<ffffffff8127b7db>] blk_cleanup_queue+0x17b/0x270
[<ffffffffa00b54c4>] __scsi_remove_device+0x54/0xd0 [scsi_mod]
[<ffffffffa00b556b>] scsi_remove_device+0x2b/0x40 [scsi_mod]
[<ffffffffa00ec47d>] storvsc_remove_lun+0x3d/0x60 [hv_storvsc]
[<ffffffff81080791>] process_one_work+0x1b1/0x530
...
The problem comes with the fact that many such jobs (for the same device)
are being scheduled simultaneously. While scsi_remove_device() uses
shost->scan_mutex and scsi_device_lookup() will fail for a device in
SDEV_DEL state there is no protection against someone who did
scsi_device_lookup() before we actually entered __scsi_remove_device(). So
the whole scenario looks like that: two callers do simultaneous (or
preemption happens) calls to scsi_device_lookup() ant these calls succeed
for both of them, after that they try doing scsi_remove_device().
shost->scan_mutex only serializes their calls to __scsi_remove_device()
and we end up doing the cleanup path twice.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If cdev_add() returns an error, the code calls
cdev_del() passing the STm->cdevs[rew] pointer as parameter;
the problem is that the pointer has not been initialized yet.
This patch fixes the problem by moving the STm->cdevs[rew] pointer
initialization before the call to cdev_add().
It also sets STm->devs[rew] and STm->cdevs[rew] to NULL in
case of failure.
Signed-off-by: Maurizio Lombardi <mlombard@redhat.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Some host adapters (e.g. Hyper-V storvsc) are known for not respecting
the SPC-2/3/4 requirement for 'INQUIRY data (see table ...) shall
contain at least 36 bytes'. As a result we get tons on 'scsi 0:7:1:1:
scsi scan: INQUIRY result too short (5), using 36' messages on
console. This can be problematic for slow consoles. Introduce
short_inquiry flag in struct Scsi_Host to print the message once per
host.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Remove firmware binary names for the ISPs, which are not submitted to
linux-firmware.
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Reviewed-by: Julian Calaby <julian.calaby@gmail.com>
Reviewed-by: Xose Vazquez Perez <xose.vazquez@gmail.com>
Cc: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Its last user was removed 10 years ago, in commit
8b05b773b6 ("[SCSI] convert st to use scsi_execute_async").
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Acked-by: Kai Mäkisara <kai.makisara@kolumbus.fi>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Building the advansys driver in a big-endian configuration such as
ARM allmodconfig shows a warning:
drivers/scsi/advansys.c: In function 'adv_build_req':
include/uapi/linux/byteorder/big_endian.h:32:26: warning: large integer implicitly truncated to unsigned type [-Woverflow]
#define __cpu_to_le32(x) ((__force __le32)__swab32((x)))
drivers/scsi/advansys.c:7806:22: note: in expansion of macro 'cpu_to_le32'
scsiqp->sense_len = cpu_to_le32(SCSI_SENSE_BUFFERSIZE);
It turns out that the commit that introduced this used the cpu_to_le32()
incorrectly on an 8-bit field, which results in the sense_len to always
be set to zero, as the SCSI_SENSE_BUFFERSIZE value gets moved to upper
byte of the 32-bit intermediate.
This removes the cpu_to_le32() call to restore the original version.
I found this only by looking at the compiler output and have not done a
full review for possible further endianess bugs in the same driver.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 811ddc057a ("advansys: use DMA-API for mapping sense buffer")
Reviewed-by: Hannes Reinecke <hare@suse.de>
Cc: stable@vger.kernel.org # v4.2+
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Sorry for the delay in this patch which was mostly caused by getting the
merger of the mpt2/mpt3sas driver, which was seen as an essential item of
maintenance work to do before the drivers diverge too much. Unfortunately,
this caused a compile failure (detected by linux-next), which then had to be
fixed up and incubated. In addition to the mpt2/3sas rework, there are
updates from pm80xx, lpfc, bnx2fc, hpsa, ipr, aacraid, megaraid_sas, storvsc
and ufs plus an assortment of changes including some year 2038 issues, a fix
for a remove before detach issue in some drivers and a couple of other minor
issues.
Signed-off-by: James Bottomley <JBottomley@Odin.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQEcBAABAgAGBQJWRnpiAAoJEDeqqVYsXL0MJd0IAIkNP1q/6ksMw/lam2UlbdxN
zFsFOIhGM3xLnBFehbCx7JW3cmybA7WC5jhMjaa1OeJmYHLpwbTzvVwrLs2l/0y1
/S+G0wwxROZfIKj/1EO3oKbSPCu9N3lStxOnmNXt5PSUEzAXrTqSNTtnMf2ZGh7j
bQxTWEJe+66GckgGw4ozTXJHWXqM/Zs/FsYjn2h/WzFhFv8utr7zRSzHMVjcqpLG
TK/Lt03hiTGqiignKrV9W6JzdGTWf2LGIsj/njgR0dxv59cNH8PrHIjZyknSBxgn
lblinsCjxDHWnP4BSfTi9MQG1lEiZiWO3Y6TKkKJTgxZ9M0Eitspc+cLOiJ1mpg=
=HvQf
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull final round of SCSI updates from James Bottomley:
"Sorry for the delay in this patch which was mostly caused by getting
the merger of the mpt2/mpt3sas driver, which was seen as an essential
item of maintenance work to do before the drivers diverge too much.
Unfortunately, this caused a compile failure (detected by linux-next),
which then had to be fixed up and incubated.
In addition to the mpt2/3sas rework, there are updates from pm80xx,
lpfc, bnx2fc, hpsa, ipr, aacraid, megaraid_sas, storvsc and ufs plus
an assortment of changes including some year 2038 issues, a fix for a
remove before detach issue in some drivers and a couple of other minor
issues"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (141 commits)
mpt3sas: fix inline markers on non inline function declarations
sd: Clear PS bit before Mode Select.
ibmvscsi: set max_lun to 32
ibmvscsi: display default value for max_id, max_lun and max_channel.
mptfusion: don't allow negative bytes in kbuf_alloc_2_sgl()
scsi: pmcraid: replace struct timeval with ktime_get_real_seconds()
mvumi: 64bit value for seconds_since1970
be2iscsi: Fix bogus WARN_ON length check
scsi_scan: don't dump trace when scsi_prep_async_scan() is called twice
mpt3sas: Bump mpt3sas driver version to 09.102.00.00
mpt3sas: Single driver module which supports both SAS 2.0 & SAS 3.0 HBAs
mpt2sas, mpt3sas: Update the driver versions
mpt3sas: setpci reset kernel oops fix
mpt3sas: Added OEM Gen2 PnP ID branding names
mpt3sas: Refcount fw_events and fix unsafe list usage
mpt3sas: Refcount sas_device objects and fix unsafe list usage
mpt3sas: sysfs attribute to report Backup Rail Monitor Status
mpt3sas: Ported WarpDrive product SSS6200 support
mpt3sas: fix for driver fails EEH, recovery from injected pci bus error
mpt3sas: Manage MSI-X vectors according to HBA device type
...
Pull SCSI target updates from Nicholas Bellinger:
"This series contains HCH's changes to absorb configfs attribute
->show() + ->store() function pointer usage from it's original
tree-wide consumers, into common configfs code.
It includes usb-gadget, target w/ drivers, netconsole and ocfs2
changes to realize the improved simplicity, that now renders the
original include/target/configfs_macros.h CPP magic for fabric drivers
and others, unnecessary and obsolete.
And with common code in place, new configfs attributes can be added
easier than ever before.
Note, there are further improvements in-flight from other folks for
v4.5 code in configfs land, plus number of target fixes for post -rc1
code"
In the meantime, a new user of the now-removed old configfs API came in
through the char/misc tree in commit 7bd1d4093c ("stm class: Introduce
an abstraction for System Trace Module devices").
This merge resolution comes from Alexander Shishkin, who updated his stm
class tracing abstraction to account for the removal of the old
show_attribute and store_attribute methods in commit 517982229f
("configfs: remove old API") from this pull. As Alexander says about
that patch:
"There's no need to keep an extra wrapper structure per item and the
awkward show_attribute/store_attribute item ops are no longer needed.
This patch converts policy code to the new api, all the while making
the code quite a bit smaller and easier on the eyes.
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>"
That patch was folded into the merge so that the tree should be fully
bisectable.
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: (23 commits)
configfs: remove old API
ocfs2/cluster: use per-attribute show and store methods
ocfs2/cluster: move locking into attribute store methods
netconsole: use per-attribute show and store methods
target: use per-attribute show and store methods
spear13xx_pcie_gadget: use per-attribute show and store methods
dlm: use per-attribute show and store methods
usb-gadget/f_serial: use per-attribute show and store methods
usb-gadget/f_phonet: use per-attribute show and store methods
usb-gadget/f_obex: use per-attribute show and store methods
usb-gadget/f_uac2: use per-attribute show and store methods
usb-gadget/f_uac1: use per-attribute show and store methods
usb-gadget/f_mass_storage: use per-attribute show and store methods
usb-gadget/f_sourcesink: use per-attribute show and store methods
usb-gadget/f_printer: use per-attribute show and store methods
usb-gadget/f_midi: use per-attribute show and store methods
usb-gadget/f_loopback: use per-attribute show and store methods
usb-gadget/ether: use per-attribute show and store methods
usb-gadget/f_acm: use per-attribute show and store methods
usb-gadget/f_hid: use per-attribute show and store methods
...
HPSA_DIAG_OPTS_DISABLE_RLD_CACHING is a mask and bitwise AND was
intended here instead of logical &&. This bug is essentially harmless,
it means that sometimes we don't print a warning message which we wanted
to print.
Fixes: c2adae44e9 ('hpsa: disable report lun data caching')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Acked-by: Don Brace <don.brace@pmcs.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
There is a static checker warning here because "val" is controlled by
the user and we have a upper bound on it but allow negative numbers.
"val" appears to be a timeout in usec so this bug probably means we
have a longer timeout than we should. Let's fix this by changing "val"
to unsigned.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Jack Wang <jinpu.wang@profitbricks.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Before enabling MPI2_SCSIIO_CONTROL_TLR_ON flag in MPI SCSI IO request
message, check whether TLR is enabled on the drive using
'sas_is_tlr_enabled' API.
Actually in the driver code, driver is using below API's
1. sas_enable_tlr() - to enable the TLR
2. sas_disable_tlr() - to disable the TLR
3. sas_is_tlr_enabled() - to check whether TLR is enabled or not.
but in scsih_qcmd() we have missed to use sas_is_tlr_enabled() API,
instead we checking for TLR bit from flag field of driver's 'struct
MPT3SAS_DEVIC' structure. which is corrected with this patch.
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
After merging the scsi tree, today's linux-next build (powerpc
allyesconfig) failed like this:
In file included from drivers/scsi/mpt3sas/mpt3sas_scsih.c:59:0:
drivers/scsi/mpt3sas/mpt3sas_scsih.c: In function '_scsih_io_done':
drivers/scsi/mpt3sas/mpt3sas_base.h:1414:1: error: inlining failed in call to always_inline 'mpt3sas_scsi_direct_io_get': function body not available
mpt3sas_scsi_direct_io_get(struct MPT3SAS_ADAPTER *ioc, u16 smid);
^
drivers/scsi/mpt3sas/mpt3sas_scsih.c:4448:6: error: called from here
if (mpt3sas_scsi_direct_io_get(ioc, smid) &&
^
In file included from drivers/scsi/mpt3sas/mpt3sas_scsih.c:59:0:
drivers/scsi/mpt3sas/mpt3sas_base.h:1416:1: error: inlining failed in call to always_inline 'mpt3sas_scsi_direct_io_set': function body not available
mpt3sas_scsi_direct_io_set(struct MPT3SAS_ADAPTER *ioc, u16 smid, u8 direct_io);
^
drivers/scsi/mpt3sas/mpt3sas_scsih.c:4454:3: error: called from here
mpt3sas_scsi_direct_io_set(ioc, smid, 0);
^
In file included from drivers/scsi/mpt3sas/mpt3sas_scsih.c:5
9:0:
drivers/scsi/mpt3sas/mpt3sas_base.h:1416:1: error: inlining failed in call to always_inline 'mpt3sas_scsi_direct_io_set': function body not available
mpt3sas_scsi_direct_io_set(struct MPT3SAS_ADAPTER *ioc, u16 smid, u8 direct_io);
^
drivers/scsi/mpt3sas/mpt3sas_scsih.c:4454:3: error: called from here
mpt3sas_scsi_direct_io_set(ioc, smid, 0);
^
Presumably caused by commit
c84b06a48c ("mpt3sas: Single driver module which supports both SAS 2.0 & SAS 3.0 HBAs")
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
According to SPC-4, in a Mode Select, the PS bit in Mode Pages is
reserved and must be set to 0 by the driver. In the sd implementation,
function cache_type_store does a Mode Sense, which might set the PS bit
on the read buffer, followed by a Mode Select, which receives the same
buffer, without explicitly clearing the PS bit. So, in cases where
target supports saving the Mode Page to a non-volatile location, we end
up doing a Mode Select with the PS bit set, which could cause an illegal
request error if the target is checking this.
This was observed on a new firmware change, which was subsequently
reverted, but this changes sd.c to be more compliant with SPC-4.
This patch clears the PS bit in the buffer returned by Mode Select,
right before it is used in the Mode Select command.
Signed-off-by: Gabriel Krisman Bertazi <krisman@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
As defined in 4.6.9 of SAM-4, the encoding of LUN is
on 5 bits (max_lun=32) and the current value is only 8.
Set max_lun to IBMVSCSI_MAX_LUN (32).
Signed-off-by: Laurent Vivier <lvivier@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
As devices with values greater than that are silently ignored,
this gives some hints to the sys admin to know why he doesn't see
his devices...
Signed-off-by: Laurent Vivier <lvivier@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Replace the use of struct timeval and do_gettimeofday() with
64 bit ktime_get_real_seconds. Prevents 32-bit type overflow
in year 2038 on 32-bit systems.
Driver was using the seconds portion of struct timeval (.tv_secs)
to pass a millseconds timestamp to the firmware. This change maintains
that same behavior using ktime_get_real_seconds.
The structure used to pass the timestamp to firmware is 48 bits and
works fine as long as the top 16 bits are zero and they will be zero
for a long time..ie. thousands of years.
Alternative Change: Add sub second granularity to timestamp
As noted above, the driver only used the seconds portion of timeval,
ignores the microseconds portion, and by multiplying by 1000 effectively
does a <<10 and always writes zero into timestamp[0].
The alternative change would pass all the bits to the firmware:
struct timespec64 ts;
ktime_get_real_ts64(&ts);
timestamp = ts.tv_sec * MSEC_PER_SEC + ts.tv_nsec / NSEC_PER_MSEC;
Signed-off-by: Alison Schofield <amsfield22@gmail.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
struct mvumi_hs_page2 stores a "seconds_since1970" field which is of
type u64. It is however, written to, using 'struct timeval' which has
a 32-bit seconds field and whose value will overflow in year 2038.
This patch uses ktime_get_real_seconds() instead since it provides a
64-bit seconds value, which is 2038 safe.
Signed-off-by: Tina Ruchandani <ruchandani.tina@gmail.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
drivers/scsi/be2iscsi/be_main.c: In function 'be_sgl_create_contiguous':
drivers/scsi/be2iscsi/be_main.c:3187:18: warning: logical not is only applied to the left hand side of comparison [-Wlogical-not-parentheses]
WARN_ON(!length > 0);
gcc version 5.2.1
Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Cc: Jayamohan Kallickal <jayamohan.kallickal@avagotech.com>
Cc: Minh Tran <minh.tran@avagotech.com>
Cc: John Soni Jose <sony.john-n@avagotech.com>
Cc: "James E.J. Bottomley" <JBottomley@odin.com>
Reported-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Manoj Kumar <manoj@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The only user of scsi_prep_async_scan() is scsi_scan_host() and it
handles the situation correctly. Move 'called twice' reporting to debug
level as well.
The issue is observed on Hyper-V: on any device add/remove event storvsc
driver calls scsi_scan_host() and in case previous scan is still running
we get the message and stack dump on console.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Reviewed-by: K. Y. Srinivasan <kys@microsoft.com>
Tested-by: Alex Ng <alexng@microsoft.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Bump mpt3sas driver version to 09.102.00.00
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Modified the mpt3sas driver to have a single driver module which
supports both SAS 2.0 & SAS 3.0 HBA devices.
* Added SAS 2.0 HBA device IDs to the mpt3sas_pci_table pci table.
* Created two separate SCSI host templates for SAS2 and SAS3 HBAs so
that, during the driver load time driver can use corresponding host
template(based the pci device ID) while registering a scsi host
adapter instance for that pci device.
* Registered two IOCTL devices, mpt2ctl is for SAS2 HBAs & mpt3ctl for
SAS3 HBAs. Also updated the code to make sure that mpt2ctl device
processes only those ioctl cmds issued for the SAS2 HBAs and mpt3ctl
device processes only those ioctl cmds issued for the SAS3 HBAs.
* Added separate indexing for SAS2 and SAS3 HBAs.
* Replaced compile time check 'MPT2SAS_SCSI' to run time check
'hba_mpi_version_belonged' whereever needed.
* Aliased this merged driver to mpt2sas using MODULE_ALIAS.
* Moved global varaible 'driver_name' to per adapter instance variable.
* Created two raid function template and used corresponding raid
function templates based on the run time check
'hba_mpi_version_belonged'.
* Moved mpt2sas_warpdrive.c file from mpt2sas to mpt3sas folder and
renamed it as mpt3sas_warpdrive.c.
* Also renamed the functions in mpt3sas_warpdrive.c file to follow
current driver function name convention.
* Updated the Makefile to build mpt3sas_warpdrive.o file for these
WarpDrive-specific functions.
* Also in function mpt3sas_setup_direct_io(), used sector_div() API
instead of division operator (which gives compilation errors on 32 bit
machines).
* Removed mpt2sas files, mpt2sas directory & mpt3sas_module.c file.
* Added module parameter 'hbas_to_enumerate' which permits using this
merged driver as a legacy mpt2sas driver or as a legacy mpt3sas
driver.
Here are the available options for this module parameter:
0 - Merged driver which enumerates both SAS 2.0 & SAS 3.0 HBAs
1 - Acts as legacy mpt2sas driver, which enumerates only SAS 2.0 HBAs
2 - Acts as legacy mpt3sas driver, which enumerates only SAS 3.0 HBAs
* Removed mpt2sas entries from SCSI's Kconfig and Makefile files.
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Bump the mpt2sas driver version to 20.102.00.00 and
Bump the mpt3sas driver version to 9.101.00.00.
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Acked-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
setpci reset on nytro warpdrive card along with sysfs access and cli
ioctl access resulted in kernel oops
1. pci_access_mutex lock added to provide synchronization between IOCTL,
sysfs, PCI resource handling path
2. gioc_lock spinlock to protect list operations over multiple
controllers
This patch is ported from commit 6229b414b3 ("mpt2sas: setpci reset
kernel oops fix").
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Acked-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Added OEM Gen2 PnP ID branding names from mpt2sas driver.
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Acked-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The fw_event_work struct is concurrently referenced at shutdown. Add a
refcount to protect it and refactor the code to use it.
Additionally, refactor _scsih_fw_event_cleanup_queue() such that it no
longer iterates over the list without holding the lock since
_firmware_event_work() concurrently deletes items from the list.
This patch is ported from commit 008549f6e8 ("mpt2sas: Refcount
fw_events and fix unsafe list usage"). These changes are also required
for mpt3sas.
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Acked-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
sas_device objects can be referenced concurrently throughout the driver.
We need a way to make sure threads can't delete them out from under each
other. This patch adds the refcount and refactors the code to use it.
Additionally, we cannot iterate over the sas_device_list without holding
the lock or we risk corrupting random memory if items are added or
deleted as we iterate. This patch refactors _scsih_probe_sas() to use
the sas_device_list in a safe way.
This patch is ported from the following mpt2sas driver commit
d224fe0d60 ("mpt2sas: Refcount sas_device objects and fix unsafe list
usage").
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Acked-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
A new sysfs shost attribute called "BMR_status" is implemented to report
Backup Rail Monitor status.
This attribute is located in:
/sys/class/scsi_host/host#/BMR_status
When reading this adapter attribute, the driver will output the state of
GPIO[24]. It returns "0" if BMR is healthy and "1" for failure.
If it returns an empty string then it means that there was an error
while obtaining the BMR status. Check dmesg for what error has occurred.
This sysfs shost attribute is mainly for WarpDrive controllers.
This commit is a port of 6c265660c2 ("mpt2sas: Provide sysfs attribute
to report Backup Rail Monitor Status").
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Acked-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Ported the following list of WarpDrive-specific patches:
1. commit 0bdccdb0a0 ("mpt2sas: WarpDrive
New product SSS6200 support added")
2. commit 82a4525812 ("mpt2sas: WarpDrive
Infinite command retries due to wrong scsi command entry in MPI
message")
3. commit ba96bd0b1d ("mpt2sas: Support
for greater than 2TB capacity WarpDrive")
4. commit 4da7af9494 ("mpt2sas: Do not
retry a timed out direct IO for Warpdrive")
5. commit daeaa9df92 ("mpt2sas: Avoid type
casting for direct I/O commands").
Also set the mpt2_ioctl_iocinfo adapter_type to:
1. MPT3_IOCTL_INTERFACE_SAS3 for Gen3 HBAs
2. MPT2_IOCTL_INTERFACE_SAS2_SSS6200 for Warp Drive
3. MPT2_IOCTL_INTERFACE_SAS2 for other Gen2 HBAs
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Acked-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch stops the driver to invoke kthread (which remove the dead
ioc) for some time while EEH recovery has started.
This patch is a port of commit b4730fb6e5 ("mpt2sas: fix for driver
fails EEH, recovery from injected pci bus error")'.
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Acked-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
1. Do not enable MSI-X vectors for SAS2008 B0 controllers
2. Enable a single MSI-X vector for the following controller:
a. SAS2004
b. SAS2008
c. SAS2008_1
d. SAS2008_2
e. SAS2008_3
f. SAS2116_1
g. SAS2116_2
3. Enable Combined Reply Post Queue Support (i.e. 96 MSI-X vectors)
for Gen3 Invader/Fury C0 and above revision HBAs
4. Enable Combined Reply Post Queue Support (i.e. 96 MSI-X vectors)
for all Intruder and Cutlass HBAs
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Acked-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Avoid sending PHYDISK_HIDDEN RAID action requests to SAS2 controllers
since they don't support it.
Also enable fast_path only for SAS3 HBAs.
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Acked-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Gen2 HBAs use MPI scatter-gather lists whereas Gen3 HBAs use IEEE
scatter-gather lists. Modify the common code part in such a way that it
will build IEEE SGL tables for Gen3 HBAs and MPI SGL tables for Gen2
HBAs.
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Acked-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently there is a logging level option provided for each of our
drivers in the kernel configuration utility. Users can enable this
option to get more verbose information. By default it is enabled.
Only when this option is enabled will the functions which display the
required information get compiled in.
As we are merging the both drivers we can no longer provide this
configuration option. Remove the SCSI_MPTXSAS_LOGGING entry from Kconfig
and unconditionally enable logging (by removing the #ifdef
CONFIG_SCSI_MPT3SAS_LOGGING preprocessor check conditions) so that all
functions which are defined to display more verbose information get
compiled in.
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Acked-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
1. Use 'hba_mpi_version_belonged' IOC varable to uniquely identify each
individual generation driver functionality at runtime.
2. Declare global variable 'driver_name' and use this variable while
reserving PCI regions and while allocating the IRQs.
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Acked-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Remove .c and .h files which are no longer needed from mpt2sas
driver. We are reusing this code from mpt3sas.
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Acked-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
1. Create a mpt2sas_module.c file for mpt2sas where GEN2 HBA devices
register with PCI, SML, IOCTL subsystems.
2. Updated the Makefile to use the object files from mpt3sas folder.
3. Defined a compilation flag SCSI_MPT2SAS which can be used to not
include those sections of code from mpt3sas driver which are not
required for mpt2sas driver.
4. Inherited automatic diag buffer feature from mpt3sas driver.
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Acked-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Created a mpt3sas_module.c file for mpt3sas driver where it can register
SAS3 HBA devices with PCI, SML, IOCTL subsystems. Also removed the
corresponding interfaces from mpt3sas_scsih.c file.
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Acked-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
1. Added mpt2sas driver related macros in mpt3sas header files
2. Made scsi host's, raid class', pci's, ioctl's callback functions
global so that both drivers can use them.
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Acked-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Use a single set of the hardware description headers instead of having
them in the source tree twice.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@avagotech.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Function stex_gettime uses 'struct timeval' whose tv_sec value
will overflow on 32-bit systems in year 2038 and beyond. This patch
replaces the use of struct timeval and do_gettimeofday with
ktime_get_real_seconds, which returns a 64-bit seconds value.
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Tina Ruchandani <ruchandani.tina@gmail.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Writing a number to /sys/bus/scsi/devices/<sdev>/queue_ramp_up_period
returns the value of that number instead of the number of bytes written.
This behavior can confuse programs expecting POSIX write() semantics.
Fix this by returning the number of bytes written instead.
Signed-off-by: Peter Oberparleiter <oberpar@linux.vnet.ibm.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Explicit logouts from bnx2fc were causing race conditions in either returning
stale SCSI commands or not allowing a target to log back in.
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Change st driver to allow enabling or disabling debug output
via sysfs file /sys/bus/scsi/drivers/st/debug_flag.
Previously the only way to enable debug output was:
1. loading the driver with the module parameter debug_flag=1
2. an ioctl call (this method was also the only way to dynamically
disable debug output).
To use the ioctl you need a second tape drive (if you are
actively testing the first tape drive) since a second process
cannot open the first tape drive if it is in use.
The this change is only functional if the value of the macro
DEBUG in st.c is a non-zero value (which it is by default).
Signed-off-by: Shane Seymour <shane.seymour@hpe.com>
Reviewed-by: Laurence Oberman <oberman.l@gmail.com>
Acked-by: Kai Mäkisara <kai.makisara@kolumbus.fi>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Signed-off-by: Sebastian Herbszt <herbszt@gmx.de>
Acked-by: Vasu Dev <vasu.dev@intel.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
This patch changes the !blk-mq path to the same defaults as the blk-mq
I/O path by always enabling block tagging, and always using host wide
tags. We've had blk-mq available for a few releases so bugs with
this mode should have been ironed out, and this ensures we get better
coverage of over tagging setup over different configs.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Jens Axboe <axboe@kernel.dk>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
When the bnx2fc driver was changed to read the npiv table from
nvram, the stack of the __bnx2fc_enable function gained an
additional 1028 byte structure that gcc rightfully warns about:
drivers/scsi/bnx2fc/bnx2fc_fcoe.c: In function '__bnx2fc_enable':
drivers/scsi/bnx2fc/bnx2fc_fcoe.c:2134:1: warning: the frame size of 1128 bytes is larger than 1024 bytes [-Wframe-larger-than=]
In order to avoid a possible kernel stack overflow and to get rid
of the warning, this changes the function to use a dynamic allocation
of the structure using kzalloc.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 2971ff67bd ("bnx2fc: Read npiv table from nvram and create vports.")
Acked-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
kmalloc() can return NULL and without checking we were dereferencing it.
Moreover if kmalloc succeeds but the function fails in other parts then
we were returning the error code but we missed freeing lcb_context.
While at it fixed one related checkpatch warning.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Reviewed-by: James Smart <james.smart@avagotech.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
There is a label pointing to the start of a while loop and a goto
nested only in the loop. The goto jumps to the label in some cases.
Replace the goto and the label by simple continue.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Acked-by: Vasu Dev <vasu.dev@intel.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Previously, when this module was unloaded via 'rmmod' with at least one
drive attached, the SCSI error handler thread would become stuck in an
infinite recovery loop and lockup the system, necessitating a reboot.
Once the SAS layer is detached, the driver will fail any subsequent
commands since the target devices are removed. However, removing the
SCSI host generates a SYNCHRONIZE CACHE (10) command, which was failed
and left the error handler no method of recovery.
This patch simply removes the SCSI host first so that no more commands
can come down, prior to cleaning up the SAS layer. Note that the stack
is built up with the SCSI host first, and then the SAS layer. Perhaps
it should be reversed for symmetry, so that commands cannot be sent to
the pm80xx driver prior to attaching the SAS layer?
What was really strange about this bug was that it was introduced at
commit cff549e486 ("[SCSI]: proper state checking and module refcount
handling in scsi_device_get"). This commit appears to tinker with how
the reference counting is performed for SCSI device objects. My theory
is that prior to this commit, the refcount for a device object was
blindly incremented at some point during the teardown process which
coincidentially made the device stick around during the procedure, which
also coincidentially made any commands sent to the driver not fail
(since the device was technically still "there"). After this commit was
applied, my theory is the refcount for the device object is not being
incremented at a specific point anymore, which makes the device go away,
and thus made the pm80xx driver fail any subsequent commands.
You may also want to see the following for more details:
[1] http://www.spinics.net/lists/linux-scsi/msg37208.html
[2] http://marc.info/?l=linux-scsi&m=144416476406993&w=2
Signed-off-by: Benjamin Rood <brood@attotech.com>
Acked-by: Jack Wang <jinpu.wang@profitbricks.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
commit cff549e486 ("scsi: proper state checking and module refcount
handling in scsi_device_get") the reference count of scsi device was
changed, which could lead to when rmmod with at least on drive attached,
SCSI error handle will run into infinite loop, and lockup the system.
Fix it by remove scsi host first, this way scsi core will not send
commands down after detaching SAS transport.
This is a follow up fix for Benjamin's fix for pm80xx.
See also:
http://www.spinics.net/lists/linux-scsi/msg90088.html
Signed-off-by: Jack Wang <jinpu.wang@profitbricks.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
commit cff549e486 ("scsi: proper state checking and module refcount
handling in scsi_device_get") the reference count of scsi device was
changed, which could lead to when rmmod with at least on drive attached,
SCSI error handle will run into infinite loop, and lockup the system.
Fix it by remove scsi host first, this way scsi core will not send
commands down after detaching SAS transport.
This is a follow up fix for Benjamin's fix for pm80xx.
See also:
http://www.spinics.net/lists/linux-scsi/msg90088.html
Signed-off-by: Jack Wang <jinpu.wang@profitbricks.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
commit cff549e486 ("scsi: proper state checking and module refcount
handling in scsi_device_get") , the reference count of scsi device was
changed, which could lead to when rmmod with at least on drive attached,
SCSI error handle will run into infinite loop, and lockup the system.
Fix it by remove scsi host first, this way scsi core will not send
commands down after detaching SAS transport.
This is a follow up fix for Benjamin's fix for pm80xx.
See also:
http://www.spinics.net/lists/linux-scsi/msg90088.html
Signed-off-by: Jack Wang <jinpu.wang@profitbricks.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Gabriel Krisman Bertazi <krisman@linux.vnet.ibm.com>
Acked-by: Brian King <brking@linux.vnet.ibm.com>
Reviewed-by: Wen Xiong <wenxiong@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
We have been getting a warning about non ANSI function.
warning: non-ANSI function declaration of function 'FPT_SccbMgrTableInitAll'
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Acked-by: Khalid Aziz <khalid@gonehiking.org>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Some new adapters require a special Configure Cache Parameters command
to enable the adapter write cache, so send this during the adapter
initialization if the adapter requires it.
Signed-off-by: Gabriel Krisman Bertazi <krisman@linux.vnet.ibm.com>
Acked-by: Brian King <brking@linux.vnet.ibm.com>
Reviewed-by: Wen Xiong <wenxiong@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add an IOA Inquiry command for Page 0xC4 during IOA initialization to
collect cache capabilities, particularly to check if Sync IOA Write
Cache is supported.
Inquiry will happen right after Cap Inquiry on page 0xD0; and will
execute only if the "Supported Pages" field in Inquiry Page 0x0 shows
support for Page 0xC4. Otherwise, assume Sync IOA Write Cache is
not supported.
Signed-off-by: Gabriel Krisman Bertazi <krisman@linux.vnet.ibm.com>
Acked-by: Brian King <brking@linux.vnet.ibm.com>
Reviewed-by: Wen Xiong <wenxiong@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
According to the IPR specification, Inhibit Underlength Checking bit
must be disabled when issuing commands to vsets. Enabling it in this
case might cause SCSI commands to fail with an Illegal Request, so make
sure we keep this bit cleared when resource is a vset.
Signed-off-by: Gabriel Krisman Bertazi <krisman@linux.vnet.ibm.com>
Reviewed-by: Manoj Kumar <manoj@linux.vnet.ibm.com>
Acked-by: Brian King <brking@linux.vnet.ibm.com>
Reviewed-by: Wen Xiong <wenxiong@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add a holding pattern prior to collecting dump data, to wait for the IOA
indication that the Mailbox register is stable and won't change without
an explicit reset. This ensures we'll be collecting meaningful dump
data, even when dumping right after an adapter reset.
In the event of a timeout, we still force the dump, since a partial dump
still might be useful.
Signed-off-by: Gabriel Krisman Bertazi <krisman@linux.vnet.ibm.com>
Acked-by: Brian King <brking@linux.vnet.ibm.com>
Reviewed-by: Wen Xiong <wenxiong@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
SRB status can have additional information. Mask these out before processing
SRB status.
This patch was sent as part of a collection of patches more than a year ago.
While the rest of the patches in the set were comitted, this patch was not.
I woulod like to thank Olaf for noticing that this patch was not committed
upstream.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Reviewed-by: Long Li <longli@microsoft.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Storvsc driver needs to ensure there are no 'holes' in the presented
sg list (all segments in the middle of the list need to be of PAGE_SIZE).
When a hole is detected storvsc driver creates a 'bounce sgl' without
holes and copies data over with copy_{to,from}_bounce_buffer() functions.
Setting virt_boundary_mask to PAGE_SIZE - 1 guarantees we'll never see
such holes so we can significantly simplify the driver. This is also
supposed to bring us some performance improvement for certain workloads
as we eliminate copying.
Reported-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Reviewed-by: K. Y. Srinivasan <kys@microsoft.com>
Tested-by: Alex Ng <alexng@microsoft.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Don't set the SRB_FLAGS_QUEUE_ACTION_ENABLE flag since we are not specifying
tags. Without this, the qlogic driver doesn't work properly with storvsc.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Cc: stable@vger.kernel.org
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Driver blocks ioctls once it received shutdown/suspend request during
suspend/hybernation. This patch unblocks ioctls on resume path.
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Reviewed-by: Murthy Bhat <Murthy.Bhat@pmcs.com>
Reviewed-by: Karthikeya Sunkesula <Karthikeya.Sunkesula@pmcs.com>
Signed-off-by: Mahesh Rajashekhara <Mahesh.Rajashekhara@pmcs.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
If 'IsFastPath' bit is set, then response path assumes no error and skips
error check.
Reviewed-by: Murthy Bhat <Murthy.Bhat@pmcs.com>
Reviewed-by: Karthikeya Sunkesula <Karthikeya.Sunkesula@pmcs.com>
Signed-off-by: Mahesh Rajashekhara <Mahesh.Rajashekhara@pmcs.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
If writeq() not supported, then do atomic two 32bit write
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Reviewed-by: Murthy Bhat <Murthy.Bhat@pmcs.com>
Reviewed-by: Karthikeya Sunkesula <Karthikeya.Sunkesula@pmcs.com>
Signed-off-by: Mahesh Rajashekhara <Mahesh.Rajashekhara@pmcs.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Driver sends the right size of the response buffer.
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Reviewed-by: Murthy Bhat <Murthy.Bhat@pmcs.com>
Reviewed-by: Karthikeya Sunkesula <Karthikeya.Sunkesula@pmcs.com>
Signed-off-by: Mahesh Rajashekhara <Mahesh.Rajashekhara@pmcs.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Signed-off-by: John Soni Jose <sony.john@avagotech.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
While posting WRB the next_pointer of the current WRB should point
to itself and the previous WRB next_pointer should point to the
current WRB.
The next pointer value was retrieved during alloc_pdu and was updated
in wrb before ringing the doorbell. The fix retrieves the
next_pointer just before ringing the doorbell and updates in the WRB.
Signed-off-by: John Soni Jose <sony.john@avagotech.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
EXTRA_CFLAGS are intended to be used on the command line, not by Kbuild.
In case of cxgbi drivers, use of EXTRA_CFLAGS results in a compilation
failure:
drivers/scsi/cxgbi/cxgb4i/cxgb4i.c:24:21: fatal error: t4_regs.h: No such file or directory
when building like:
$ make drivers/scsi/cxgbi/ EXTRA_CFLAGS=-Wwhatever
Use ccflags-y instead of EXTRA_CFLAGS.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
New revisions of UFS host controller supports the new UniPro
hardware controller (referred as QUniPro). This patch adds
the support to enable this new UniPro controller hardware.
This change also adds power optimization for bus scaling feature,
as well as support for HS-G3 power mode.
Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org>
Reviewed-by: Gilad Broner <gbroner@codeaurora.org>
Signed-off-by: Yaniv Gardi <ygardi@codeaurora.org>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Adds support for configuring and reading the test bus and debug
registers. This change also adds another vops in order to print the
debug registers.
Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org>
Reviewed-by: Gilad Broner <gbroner@codeaurora.org>
Signed-off-by: Yaniv Gardi <ygardi@codeaurora.org>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This change turns the UFS variant (SCSI_UFS_QCOM) into a UFS
a platform device.
In order to do so a few additional changes are required:
1. The ufshcd-pltfrm is no longer serves as a platform device.
Now it only serves as a group of platform APIs such as PM APIs
(runtime suspend/resume, system suspend/resume etc), parsers of
clocks, regulators and pm_levels from DT.
2. What used to be the old platform "probe" is now "only"
a pltfrm_init() routine, that does exactly the same, but only
being called by the new probe function of the UFS variant.
Reviewed-by: Rob Herring <robherring2@gmail.com>
Reviewed-by: Gilad Broner <gbroner@codeaurora.org>
Signed-off-by: Yaniv Gardi <ygardi@codeaurora.org>
Tested-by: Alim Akhtar <alim.akhtar@samsung.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In order to simplify the code a set of wrapper functions is created
to test and call each of the variant operations.
Reviewed-by: Akinobu Mita <akinobu.mita@gmail.com>
Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org>
Reviewed-by: Gilad Broner <gbroner@codeaurora.org>
Signed-off-by: Yaniv Gardi <ygardi@codeaurora.org>
Tested-by: Alim Akhtar <alim.akhtar@samsung.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch adds ufshcd_get_variant() and ufshcd_set_variant()
routines in order to get/set the variant specific data.
Reviewed-by: Akinobu Mita <akinobu.mita@gmail.com>
Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org>
Reviewed-by: Gilad Broner <gbroner@codeaurora.org>
Signed-off-by: Yaniv Gardi <ygardi@codeaurora.org>
Tested-by: Alim Akhtar <alim.akhtar@samsung.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This change is required in order to be able to build the component
as a module.
Reviewed-by: Akinobu Mita <akinobu.mita@gmail.com>
Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org>
Reviewed-by: Gilad Broner <gbroner@codeaurora.org>
Signed-off-by: Yaniv Gardi <ygardi@codeaurora.org>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This change fixes a compilation warning that happens if SCSI_UFS_QCOM is
compiled as a module. Also this patch fixes an error happens when
insmod the module: "ufs_qcom: module license 'unspecified' taints
kernel."
Reviewed-by: Akinobu Mita <akinobu.mita@gmail.com>
Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org>
Reviewed-by: Gilad Broner <gbroner@codeaurora.org>
Signed-off-by: Yaniv Gardi <ygardi@codeaurora.org>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch fixes a 'general protection fault' issue by
moving the attribute to where it was likely meant.
Signed-off-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Don Brace <don.brace@pmcs.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Justin Lindley <justin.lindley@pmcs.com>
Reviewed-by: Scott Teel <scott.teel@pmcs.com>
Reviewed-by: Kevin Barnett <kevin.barnett@pmcs.com>
Reviewed-by: Gerry Morong <gerry.morong.pmcs.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: Don Brace <don.brace@pmcs.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Scott Teel <scott.teel@pmcs.com>
Reviewed-by: Justin Lindley <justin.lindley@pmcs.com>
Reviewed-by: Kevin Barnett <kevin.barnett@pmcs.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Reviewed-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: Don Brace <don.brace@pmcs.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
path_info_show() seems to be broken in multiple ways.
First, there's
817 return snprintf(buf, output_len+1, "%s%s%s%s%s%s%s%s",
818 path[0], path[1], path[2], path[3],
819 path[4], path[5], path[6], path[7]);
so hopefully output_len contains the combined length of the eight
strings. Otherwise, snprintf will stop copying to the output
buffer, but still end up reporting that combined length - which
in turn would result in user-space getting a bunch of useless nul
bytes (thankfully the upper sysfs layer seems to clear the output
buffer before passing it to the various ->show routines). But we have
767 output_len = snprintf(path[i],
768 PATH_STRING_LEN, "[%d:%d:%d:%d] %20.20s ",
769 h->scsi_host->host_no,
770 hdev->bus, hdev->target, hdev->lun,
771 scsi_device_type(hdev->devtype));
so output_len at best contains the length of the last string printed.
Inside the loop, we then otherwise add to output_len. By magic,
we still have PATH_STRING_LEN available every time... This
wouldn't really be a problem if the bean-counting has been done
properly and each line actually does fit in 50 bytes, and maybe
it does, but I don't immediately see why. Suppose we end up
taking this branch:
802 output_len += snprintf(path[i] + output_len,
803 PATH_STRING_LEN,
804 "BOX: %hhu BAY: %hhu %s\n",
805 box, bay, active);
An optimistic estimate says this uses strlen("BOX: 1 BAY: 2
Active\n") which is 21. Now add the 20 bytes guaranteed by the
%20.20s and then some for the rest of that format string, and
we're easily over 50 bytes. I don't think we can get over 100
bytes even being pessimistic, so this just means we'll scribble
into the next path[i+1] and maybe get that overwritten later,
leading to some garbled output (in fact, since we'd overwrite the
previous string's 0-terminator, we could end up with one very
long string and then print various suffixes of that, leading to
much more than 400 bytes of output). Except of course when we're
filling path[7], where overrunning it means writing random stuff
to the kernel stack, which is usually a lot of fun.
We can fix all of that and get rid of the 400 byte stack buffer by
simply writing directly to the given output buffer, which the upper
layer guarantees is at least PAGE_SIZE. s[c]nprintf doesn't care where
it is writing to, so this doesn't make the spin lock hold time any
longer. Using scnprintf ensures that output_len always represents the
number of bytes actually written to the buffer, so we'll report the
proper amount to the upper layer.
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Reviewed-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Don Brace <don.brace@pmcs.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Justin Lindley <justin.lindley@pmcs.com>
Reviewed-by: Scott Teel <scott.teel@pmcs.com>
Reviewed-by: Kevin Barnett <kevin.barnett@pmcs.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: Don Brace <don.brace@pmcs.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When external target arrays are present, disable the firmware's
normal behavior of returning a cached copy of the report lun data,
and force it to collect new data each time we request a report luns.
This is necessary for external arrays, since there may be no
reliable signal from the external array to the smart array when
lun configuration changes, and thus when driver requests
report luns, it may be stale data.
Use diag options to turn off RPL data caching.
Reviewed-by: Scott Teel <scott.teel@pmcs.com>
Reviewed-by: Justin Lindley <justin.lindley@pmcs.com>
Reviewed-by: Kevin Barnett <kevin.barnett@pmcs.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: Don Brace <don.brace@pmcs.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
There are problems with getting configuration change notification
in pass-through RAID environments. So, activate flag
h->discovery_polling when one of these devices is detected in
update_scsi_devices.
After discovery_polling is set, execute a report luns from
rescan_controller_worker (every 30 seconds).
If the data from report_luns is different than last
time (binary compare), execute a full rescan via update_scsi_devices.
Reviewed-by: Scott Teel <scott.teel@pmcs.com>
Reviewed-by: Justin Lindley <justin.lindley@pmcs.com>
Reviewed-by: Kevin Barnett <kevin.barnett@pmcs.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: Don Brace <don.brace@pmcs.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
We don't need to create fake enclosure devices at Lun0
in external target array configurations anymore.
This was done to support Pre-SCSI rev 5 controllers
that didn't suppoprt report luns commands, so the
SCSI layer had to scan targets. If there was no
LUN at LUN 0, then the target scan would stop, and
move to the next target. Lun0 enclosure device
was added to prevent sparsely-numbered LUNs from
being missed.
Reviewed-by: Scott Teel <scott.teel@pmcs.com>
Reviewed-by: Justin Lindley <justin.lindley@pmcs.com>
Reviewed-by: Kevin Barnett <kevin.barnett@pmcs.com>
Reviewed-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Don Brace <don.brace@pmcs.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
External array LUNs must use target and lun numbers assigned by the
external array. So the driver must treat these differently from
local LUNs when assigning lun/target.
LUN's 'model' field has been used to detect Lun types that need
special treatment, but the desire is to eliminate the need to reference
specific array models, and support any external array.
Pass-through RAID (PTRAID) luns are not luns of the local controller,
so they are not reported in LUN count of command 'ID controller'.
However, they ARE reported in "Report logical Luns" command.
Local luns are listed first, then PTRAID LUNs.
The number of luns from "Report LUNs" in excess of those reported by
'ID controller' are therefore the PTRAID LUNS.
We can now remove function is_ext_target, and the 'white list'
array of supported model names.
Reviewed-by: Scott Teel <scott.teel@pmcs.com>
Reviewed-by: Justin Lindley <justin.lindley@pmcs.com>
Reviewed-by: Kevin Barnett <kevin.barnett@pmcs.com>
Signed-off-by: Don Brace <don.brace@pmcs.com>
Reviewed-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
preparation for adding the sas transport class
Reviewed-by: Scott Teel <scott.teel@pmcs.com>
Reviewed-by: Justin Lindley <justin.lindley@pmcs.com>
Reviewed-by: Kevin Barnett <kevin.barnett@pmcs.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: Don Brace <don.brace@pmcs.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
setup for sas transport. Need to set the
bus and target accordingly.
Reviewed-by: Scott Teel <scott.teel@pmcs.com>
Reviewed-by: Justin Lindley <justin.lindley@pmcs.com>
Reviewed-by: Kevin Barnett <kevin.barnett@pmcs.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Don Brace <don.brace@pmcs.com>
Reviewed-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
use an index into vpd data for SAS/SATA drives
Reviewed-by: Scott Teel <scott.teel@pmcs.com>
Reviewed-by: Justin Lindley <justin.lindley@pmcs.com>
Reviewed-by: Kevin Barnett <kevin.barnett@pmcs.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Reviewed-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: Don Brace <don.brace@pmcs.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
simplify checking for logical/physical devices
Reviewed-by: Scott Teel <scott.teel@pmcs.com>
Reviewed-by: Justin Lindley <justin.lindley@pmcs.com>
Reviewed-by: Kevin Barnett <kevin.barnett@pmcs.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Reviewed-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Don Brace <don.brace@pmcs.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
remove repeated calculation that checks for physical
or logical devices.
Reviewed-by: Scott Teel <scott.teel@pmcs.com>
Reviewed-by: Justin Lindley <justin.lindley@pmcs.com>
Reviewed-by: Kevin Barnett <kevin.barnett@pmcs.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Reviewed-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Don Brace <don.brace@pmcs.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
remove macros and cleanup device exposure checking
Reviewed-by: Scott Teel <scott.teel@pmcs.com>
Reviewed-by: Justin Lindley <justin.lindley@pmcs.com>
Reviewed-by: Kevin Barnett <kevin.barnett@pmcs.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Don Brace <don.brace@pmcs.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Scott Teel <scott.teel@pmcs.com>
Reviewed-by: Justin Lindley <justin.lindley@pmcs.com>
Reviewed-by: Kevin Barnett <kevin.barnett@pmcs.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Don Brace <don.brace@pmcs.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver is using two MACROs which seemingly are looking in
the wrong location for the device_flags returned from
CISS_REPORT_PHYS. Both MACROs, NON_DISK_PHYS_DEV and
PHYS_IOACCEL, are using the pointer returned from figure_lunaddrbytes
which is the address of the LUN.lunid element in
the extended CISS_REPORT_PHYS. But the MACROS are using offsets
beyond the range of the element (offset 17 of an 8 byte element).
These MACROs actually are looking at the correct location but
they fail static checker analysis. It also will not work
if any new elements are added to the extended LUN structure.
Change the code to use the structure elements directly
since this MACRO is only used in one location.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Scott Teel <scott.teel@pmcs.com>
Reviewed-by: Justin Lindley <justin.lindley@pmcs.com>
Reviewed-by: Kevin Barnett <kevin.barnett@pmcs.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Don Brace <don.brace@pmcs.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Set reset type in device_reset_handler to do either
logical unit reset for logical devices, or physical
target reset, for physical devices.
Reviewed-by: Scott Teel <scott.teel@pmcs.com>
Reviewed-by: Justin Lindley <justin.lindley@pmcs.com>
Reviewed-by: Kevin Barnett <kevin.barnett@pmcs.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Don Brace <don.brace@pmcs.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fix a NULL pointer issue in the driver when devices are removed
during a reset.
Signed-off-by: Don Brace <don.brace@pmcs.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
handle block counts of 0. Cleanup block and block count calculations.
Reviewed-by: Scott Teel <scott.teel@pmcs.com>
Reviewed-by: Justin Lindley <justin.lindley@pmcs.com>
Reviewed-by: Kevin Barnett <kevin.barnett@pmcs.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Don Brace <don.brace@pmcs.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Abandon and reschedule rescan process only if device inquiries
fail due to mem alloc failures, which are likely to occur for
all devices.
Otherwise, skip device if inquiry fails for other reasons,
and continue rescanning process for other devices.
Reviewed-by: Scott Teel <scott.teel@pmcs.com>
Reviewed-by: Justin Lindley <justin.lindley@pmcs.com>
Reviewed-by: Kevin Barnett <kevin.barnett@pmcs.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Don Brace <don.brace@pmcs.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Scott Teel <scott.teel@pmcs.com>
Reviewed-by: Justin Lindley <justin.lindley@pmcs.com>
Reviewed-by: Kevin Barnett <kevin.barnett@pmcs.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Reviewed-by; Hannes Reinecke <hare@suse.de>
Signed-off-by: Don Brace <don.brace@pmcs.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Reviewed-by: Manoj Kumar <manoj@linux.vnet.ibm.com>
Signed-off-by: Don Brace <don.brace@pmcs.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Check for NULLs.
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Reviewed-by: Manoj Kumar <manoj@linux.vnet.ibm.com>
Signed-off-by: Don Brace <don.brace@pmcs.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This member is used in calls to scsi_device_type.
It should be unsigned since the kernel checks for upper bounds
and it should never be negative.
Suggested-by: Tomas Henzl <thenzl@redhat.com>
Suggested-by: Hannes Reinecke <hare@suse.de>
Suggested-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: Don Brace <don.brace@pmcs.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This function is no longer used.
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Don Brace <don.brace@pmcs.com>
Reviewed-by: Manoj Kumar <manoj@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
pulling the rug out from under the reset handler
likewise for ioaccel_cmds_out
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Don Brace <don.brace@pmcs.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This parameter was once used before scan_start was defined
but now it is no longer used.
Signed-off-by: Don Brace <don.brace@pmcs.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Writing a number to /sys/bus/scsi/devices/<sdev>/queue_ramp_up_period
returns the value of that number instead of the number of bytes written.
This behavior can confuse programs expecting POSIX write() semantics.
Fix this by returning the number of bytes written instead.
Signed-off-by: Peter Oberparleiter <oberpar@linux.vnet.ibm.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Cc: stable@vger.kernel.org
Reviewed-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Export the RAW SCSI Inquiry to sysfs as binfile. This way the data can be used
by userland without the need to have and ioctl or use the sg_inq tool.
Here is an example of the provided data
linux:~ # hexdump /sys/class/scsi_device/1\:0\:0\:0/device/inquiry
0000000 8005 3205 001f 0000 4551 554d 2020 2020
0000010 4551 554d 4420 4456 522d 4d4f 2020 2020
0000020 2e32 2e33
0000024
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The DELL PERC5 controller firmware does not list tape drives in response
to MR_DCMD_PD_LIST_QUERY. This causes tape drives not be exposed to the
OS when connected to a PERC5 controller.
This patch permits detection of tape drives connected to a PERC5
controller by exposing non-TYPE_DISK devices unconditionally.
Signed-off-by: Kashyap Desai <kashyap.desai@avagotech.com>
Signed-off-by: Sumit Saxena <sumit.saxena@avagotech.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Merge second patch-bomb from Andrew Morton:
- most of the rest of MM
- procfs
- lib/ updates
- printk updates
- bitops infrastructure tweaks
- checkpatch updates
- nilfs2 update
- signals
- various other misc bits: coredump, seqfile, kexec, pidns, zlib, ipc,
dma-debug, dma-mapping, ...
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (102 commits)
ipc,msg: drop dst nil validation in copy_msg
include/linux/zutil.h: fix usage example of zlib_adler32()
panic: release stale console lock to always get the logbuf printed out
dma-debug: check nents in dma_sync_sg*
dma-mapping: tidy up dma_parms default handling
pidns: fix set/getpriority and ioprio_set/get in PRIO_USER mode
kexec: use file name as the output message prefix
fs, seqfile: always allow oom killer
seq_file: reuse string_escape_str()
fs/seq_file: use seq_* helpers in seq_hex_dump()
coredump: change zap_threads() and zap_process() to use for_each_thread()
coredump: ensure all coredumping tasks have SIGNAL_GROUP_COREDUMP
signal: remove jffs2_garbage_collect_thread()->allow_signal(SIGCONT)
signal: introduce kernel_signal_stop() to fix jffs2_garbage_collect_thread()
signal: turn dequeue_signal_lock() into kernel_dequeue_signal()
signals: kill block_all_signals() and unblock_all_signals()
nilfs2: fix gcc uninitialized-variable warnings in powerpc build
nilfs2: fix gcc unused-but-set-variable warnings
MAINTAINERS: nilfs2: add header file for tracing
nilfs2: add tracepoints for analyzing reading and writing metadata files
...
Pull trivial updates from Jiri Kosina:
"Trivial stuff from trivial tree that can be trivially summed up as:
- treewide drop of spurious unlikely() before IS_ERR() from Viresh
Kumar
- cosmetic fixes (that don't really affect basic functionality of the
driver) for pktcdvd and bcache, from Julia Lawall and Petr Mladek
- various comment / printk fixes and updates all over the place"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial:
bcache: Really show state of work pending bit
hwmon: applesmc: fix comment typos
Kconfig: remove comment about scsi_wait_scan module
class_find_device: fix reference to argument "match"
debugfs: document that debugfs_remove*() accepts NULL and error values
net: Drop unlikely before IS_ERR(_OR_NULL)
mm: Drop unlikely before IS_ERR(_OR_NULL)
fs: Drop unlikely before IS_ERR(_OR_NULL)
drivers: net: Drop unlikely before IS_ERR(_OR_NULL)
drivers: misc: Drop unlikely before IS_ERR(_OR_NULL)
UBI: Update comments to reflect UBI_METAONLY flag
pktcdvd: drop null test before destroy functions
__GFP_WAIT was used to signal that the caller was in atomic context and
could not sleep. Now it is possible to distinguish between true atomic
context and callers that are not willing to sleep. The latter should
clear __GFP_DIRECT_RECLAIM so kswapd will still wake. As clearing
__GFP_WAIT behaves differently, there is a risk that people will clear the
wrong flags. This patch renames __GFP_WAIT to __GFP_RECLAIM to clearly
indicate what it does -- setting it allows all reclaim activity, clearing
them prevents it.
[akpm@linux-foundation.org: fix build]
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Mel Gorman <mgorman@techsingularity.net>
Acked-by: Michal Hocko <mhocko@suse.com>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Cc: Christoph Lameter <cl@linux.com>
Acked-by: David Rientjes <rientjes@google.com>
Cc: Vitaly Wool <vitalywool@gmail.com>
Cc: Rik van Riel <riel@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
